F3-PWE3-MIB

Imported modules

SNMPv2-CONF	SNMPv2-SMI	SNMPv2-TC
CM-ENTITY-MIB	CM-FACILITY-MIB	CM-COMMON-MIB
ADVA-MIB

Imported symbols

MODULE-COMPLIANCE	OBJECT-GROUP	NOTIFICATION-GROUP
MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
IpAddress	Integer32	Unsigned32
Counter64	DisplayString	TruthValue
RowStatus	StorageType	VariablePointer
MacAddress	DateAndTime	TEXTUAL-CONVENTION
neIndex	shelfIndex	slotIndex
cmEthernetAccPortIndex	cmEthernetNetPortIndex	IpVersion
CmPmIntervalType	CmPmBinAction	VlanId
VlanPriority	fsp150cm	AdminState
OperationalState	SecondaryState	PerfCounter64
IpPriorityMapMode

Defined Types

PWE3SatopDiscoveryType
Enumerations for PWE3 SATop Discovery Type.
TEXTUAL-CONVENTION
	INTEGER	dynamic(1), static(2)

PWE3SatopEncapsulationType
Enumerations for PWE3 SATop Encapsulation Type.
TEXTUAL-CONVENTION
	INTEGER	vlan-one-mpls-label(1), vlan-two-mpls-label(2), novlan-two-mpls-label(3)

PWE3SatopRTPTSUpdateFreqType
Enumerations for PWE3 SATop RTP Update Frequency.
TEXTUAL-CONVENTION
	INTEGER	freq-8kHz(1), freq-16kHz(2), freq-32kHz(3), freq-64kHz(4), freq-128kHz(5), freq-256kHz(6), freq-512kHz(7), freq-1024kHz(8)

PWE3SatopTransportMode
Enumerations for PWE3 SATop Transport Mode.
TEXTUAL-CONVENTION
	INTEGER	satop-e1(1), satop-t1(2), satop-octetalignt1(3)

MplsLabel
Definition of MPLS Label. The bits in network order (left-to-right) are, Label(20-bits):QOS(3-bits):Bottom-of-Stack(1-bit):TTL(8-bits) These constitute the 32-bit unsigned integer.
TEXTUAL-CONVENTION
	Unsigned32

F3Pwe3IdlePatternProfileEntry
SEQUENCE
	f3Pwe3IdlePatternProfileIndex	Integer32
	f3Pwe3IdlePatternProfileByte	Unsigned32

F3Pwe3ResyncProfileEntry
SEQUENCE
	f3Pwe3ResyncProfileIndex	Integer32
	f3Pwe3ResyncProfileIncreaseFactor	Unsigned32
	f3Pwe3ResyncProfileDecreaseFactor	Unsigned32
	f3Pwe3ResyncProfileResyncThreshold	Unsigned32

F3Pwe3LoopbackProfileEntry
SEQUENCE
	f3Pwe3LoopbackProfileIndex	Integer32
	f3Pwe3LoopbackProfileLength	Unsigned32
	f3Pwe3LoopbackProfilePattern	Unsigned32
	f3Pwe3LoopbackProfileRepeatTime	Unsigned32
	f3Pwe3LoopbackProfileClearLength	Unsigned32
	f3Pwe3LoopbackProfileClearPattern	Unsigned32

F3Pwe3LossProfileEntry
SEQUENCE
	f3Pwe3LossProfileIndex	Integer32
	f3Pwe3LossProfileLossStateEnterTime	Unsigned32
	f3Pwe3LossProfileLossStateExitTime	Unsigned32

F3Pwe3AisStabilizationProfileEntry
SEQUENCE
	f3Pwe3AisStabilizationProfileIndex	Integer32
	f3Pwe3AisStabilizationProfileEnterTime	Unsigned32
	f3Pwe3AisStabilizationProfileExitTime	Unsigned32

F3Pwe3SatopEntry
SEQUENCE
	f3Pwe3SatopIndex	Integer32
	f3Pwe3SatopAlias	DisplayString
	f3Pwe3SatopAdminState	AdminState
	f3Pwe3SatopOperationalState	OperationalState
	f3Pwe3SatopSecondaryState	SecondaryState
	f3Pwe3SatopTDMEntity	VariablePointer
	f3Pwe3SatopDiscoveryType	PWE3SatopDiscoveryType
	f3Pwe3SatopRemoteIpAddress	IpAddress
	f3Pwe3SatopRemoteMacAddress	MacAddress
	f3Pwe3SatopEncapsulationType	PWE3SatopEncapsulationType
	f3Pwe3SatopRTPEnabled	TruthValue
	f3Pwe3SatopRTPUpdateFrequency	PWE3SatopRTPTSUpdateFreqType
	f3Pwe3SatopControlWordEnabled	TruthValue
	f3Pwe3SatopJitterBufferSize	Unsigned32
	f3Pwe3SatopPayloadSize	Unsigned32
	f3Pwe3SatopVlanId	VlanId
	f3Pwe3SatopVlanPriority	VlanPriority
	f3Pwe3SatopRxMplsLabel1	MplsLabel
	f3Pwe3SatopRxMplsLabel2	MplsLabel
	f3Pwe3SatopTxMplsLabel1	MplsLabel
	f3Pwe3SatopTxMplsLabel2	MplsLabel
	f3Pwe3SatopAisStabilizationProfile	VariablePointer
	f3Pwe3SatopResyncProfile	VariablePointer
	f3Pwe3SatopLossProfile	VariablePointer
	f3Pwe3SatopTransportMode	PWE3SatopTransportMode
	f3Pwe3SatopStorageType	StorageType
	f3Pwe3SatopRowStatus	RowStatus

F3Pwe3SatopTDMEntitiesEntry
SEQUENCE
	f3Pwe3SatopTDMEntityIndex	Integer32
	f3Pwe3SatopTDMEntityObject	VariablePointer
	f3Pwe3SatopTDMEntityStorageType	StorageType
	f3Pwe3SatopTDMEntityRowStatus	RowStatus

F3Pwe3SatopStatsEntry
SEQUENCE
	f3Pwe3SatopStatsIndex	Integer32
	f3Pwe3SatopStatsIntervalType	CmPmIntervalType
	f3Pwe3SatopStatsValid	TruthValue
	f3Pwe3SatopStatsAction	CmPmBinAction
	f3Pwe3SatopStatsESs	PerfCounter64
	f3Pwe3SatopStatsSESs	PerfCounter64
	f3Pwe3SatopStatsEBs	PerfCounter64
	f3Pwe3SatopStatsResyncs	PerfCounter64
	f3Pwe3SatopStatsMaxJitter	Unsigned32
	f3Pwe3SatopStatsFramesTx	PerfCounter64
	f3Pwe3SatopStatsPayloadOctetsTx	PerfCounter64
	f3Pwe3SatopStatsFramesRx	PerfCounter64
	f3Pwe3SatopStatsPayloadOctetsRx	PerfCounter64
	f3Pwe3SatopStatsOutOfSeqFramesRx	PerfCounter64
	f3Pwe3SatopStatsLostFrames	PerfCounter64
	f3Pwe3SatopStatsLostFramesStateTrans	PerfCounter64
	f3Pwe3SatopStatsMalformedFramesRx	PerfCounter64
	f3Pwe3SatopStatsJitterBufferLateFrames	PerfCounter64

F3Pwe3SatopHistoryEntry
SEQUENCE
	f3Pwe3SatopHistoryIndex	Integer32
	f3Pwe3SatopHistoryTime	DateAndTime
	f3Pwe3SatopHistoryValid	TruthValue
	f3Pwe3SatopHistoryAction	CmPmBinAction
	f3Pwe3SatopHistoryESs	PerfCounter64
	f3Pwe3SatopHistorySESs	PerfCounter64
	f3Pwe3SatopHistoryEBs	PerfCounter64
	f3Pwe3SatopHistoryResyncs	PerfCounter64
	f3Pwe3SatopHistoryMaxJitter	Unsigned32
	f3Pwe3SatopHistoryFramesTx	PerfCounter64
	f3Pwe3SatopHistoryPayloadOctetsTx	PerfCounter64
	f3Pwe3SatopHistoryFramesRx	PerfCounter64
	f3Pwe3SatopHistoryPayloadOctetsRx	PerfCounter64
	f3Pwe3SatopHistoryOutOfSeqFramesRx	PerfCounter64
	f3Pwe3SatopHistoryLostFrames	PerfCounter64
	f3Pwe3SatopHistoryLostFramesStateTrans	PerfCounter64
	f3Pwe3SatopHistoryMalformedFramesRx	PerfCounter64
	f3Pwe3SatopHistoryJitterBufferLateFrames	PerfCounter64

F3Pwe3SatopThresholdEntry
SEQUENCE
	f3Pwe3SatopThresholdIndex	Integer32
	f3Pwe3SatopThresholdInterval	CmPmIntervalType
	f3Pwe3SatopThresholdVariable	VariablePointer
	f3Pwe3SatopThresholdValueLo	Unsigned32
	f3Pwe3SatopThresholdValueHi	Unsigned32
	f3Pwe3SatopThresholdMonValue	Counter64

Defined Values

f3Pwe3MIB		1.3.6.1.4.1.2544.1.12.19
This module provides the F3 Pseudo Wire definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA Optical Networking.
MODULE-IDENTITY

f3Pwe3ConfigObjects		1.3.6.1.4.1.2544.1.12.19.1
OBJECT IDENTIFIER

f3Pwe3PerformanceObjects		1.3.6.1.4.1.2544.1.12.19.2
OBJECT IDENTIFIER

f3Pwe3PerformanceNotifications		1.3.6.1.4.1.2544.1.12.19.3
OBJECT IDENTIFIER

f3Pwe3Conformance		1.3.6.1.4.1.2544.1.12.19.4
OBJECT IDENTIFIER

f3Pwe3IdlePatternProfileTable		1.3.6.1.4.1.2544.1.12.19.1.1
A list of entries corresponding to the PWE3 Idle Pattern Profile entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		F3Pwe3IdlePatternProfileEntry

f3Pwe3IdlePatternProfileEntry		1.3.6.1.4.1.2544.1.12.19.1.1.1
An entry containing information applicable to a particular PWE3 Idle Pattern Profile Entity. These profiles are used by PWE3 SAToP entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	F3Pwe3IdlePatternProfileEntry

f3Pwe3IdlePatternProfileIndex		1.3.6.1.4.1.2544.1.12.19.1.1.1.1
Unique index value associated with the PWE3 Idle Pattern Profile.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

f3Pwe3IdlePatternProfileByte		1.3.6.1.4.1.2544.1.12.19.1.1.1.2
This object allows SNMP management entities to specify the Idle Pattern Profile information.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3ResyncProfileTable		1.3.6.1.4.1.2544.1.12.19.1.2
A list of entries corresponding to the PWE3 Resync Profile entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		F3Pwe3ResyncProfileEntry

f3Pwe3ResyncProfileEntry		1.3.6.1.4.1.2544.1.12.19.1.2.1
An entry containing information applicable to a particular PWE3 Resync Profile Entity. These profiles are used by PWE3 SAToP entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	F3Pwe3ResyncProfileEntry

f3Pwe3ResyncProfileIndex		1.3.6.1.4.1.2544.1.12.19.1.2.1.1
Unique index value associated with the PWE3 Resync Profile.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

f3Pwe3ResyncProfileIncreaseFactor		1.3.6.1.4.1.2544.1.12.19.1.2.1.2
This object allows SNMP management entities to specify the PWE3 Resync Profile Increase Factor. This is used to define the fill rate of the leaky bucket algorithm associated with the Resync mechanism.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3ResyncProfileDecreaseFactor		1.3.6.1.4.1.2544.1.12.19.1.2.1.3
This object allows SNMP management entities to specify the PWE3 Resync Profile Decrease Factor. This is used to define the leak rate for the leaky bucket algorithm associated with the Resync mechanism.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3ResyncProfileResyncThreshold		1.3.6.1.4.1.2544.1.12.19.1.2.1.4
This object allows SNMP management entities to specify the PWE3 Resync Profile Resync Threshold. This is the threshold value at which point the pseudo-wire connection is deemed out of synchronization state.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3LoopbackProfileTable		1.3.6.1.4.1.2544.1.12.19.1.3
A list of entries corresponding to the PWE3 Loopback Profile entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		F3Pwe3LoopbackProfileEntry

f3Pwe3LoopbackProfileEntry		1.3.6.1.4.1.2544.1.12.19.1.3.1
An entry containing information applicable to a particular PWE3 Loopback Profile Entity. These profiles are used by PWE3 T1/E1 interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	F3Pwe3LoopbackProfileEntry

f3Pwe3LoopbackProfileIndex		1.3.6.1.4.1.2544.1.12.19.1.3.1.1
Unique index value associated with the PWE3 Loopback Profile.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

f3Pwe3LoopbackProfileLength		1.3.6.1.4.1.2544.1.12.19.1.3.1.2
This object allows SNMP management entities to specify the PWE3 Loopback Length.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3LoopbackProfilePattern		1.3.6.1.4.1.2544.1.12.19.1.3.1.3
This object allows SNMP management entities to specify the PWE3 Loopback Pattern.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3LoopbackProfileRepeatTime		1.3.6.1.4.1.2544.1.12.19.1.3.1.4
This object allows SNMP management entities to specify the PWE3 Loopback Profile Repeat Time (Duration).
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3LoopbackProfileClearLength		1.3.6.1.4.1.2544.1.12.19.1.3.1.5
This object allows SNMP management entities to specify the Loopback PWE3 Clear Length.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3LoopbackProfileClearPattern		1.3.6.1.4.1.2544.1.12.19.1.3.1.6
This object allows SNMP management entities to specify the PWE3 Loopback Clear Pattern.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3LossProfileTable		1.3.6.1.4.1.2544.1.12.19.1.4
A list of entries corresponding to the PWE3 Loss Profile entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		F3Pwe3LossProfileEntry

f3Pwe3LossProfileEntry		1.3.6.1.4.1.2544.1.12.19.1.4.1
An entry containing information applicable to a particular PWE3 Loss Profile Entity. These profiles are used by PWE3 SAToP entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	F3Pwe3LossProfileEntry

f3Pwe3LossProfileIndex		1.3.6.1.4.1.2544.1.12.19.1.4.1.1
Unique index value associated with the PWE3 Loss Profile.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

f3Pwe3LossProfileLossStateEnterTime		1.3.6.1.4.1.2544.1.12.19.1.4.1.2
This object allows SNMP management entities to specify the holdoff time that will be applied prior to the SAToP instance entering a Loss State.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3LossProfileLossStateExitTime		1.3.6.1.4.1.2544.1.12.19.1.4.1.3
This object allows SNMP management entities to specify the holdon time that will be applied when the conditon causing the loss state clears.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3AisStabilizationProfileTable		1.3.6.1.4.1.2544.1.12.19.1.5
A list of entries corresponding to the PWE3 AisStabilization Profile entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		F3Pwe3AisStabilizationProfileEntry

f3Pwe3AisStabilizationProfileEntry		1.3.6.1.4.1.2544.1.12.19.1.5.1
An entry containing information applicable to a particular PWE3 AisStabilization Profile Entity. These profiles are used by PWE3 SAToP entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	F3Pwe3AisStabilizationProfileEntry

f3Pwe3AisStabilizationProfileIndex		1.3.6.1.4.1.2544.1.12.19.1.5.1.1
Unique index value associated with the PWE3 AIS Stabilization Profile.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

f3Pwe3AisStabilizationProfileEnterTime		1.3.6.1.4.1.2544.1.12.19.1.5.1.2
This object allows SNMP management entities to specify the time (in hundreds of milliseconds) that will be applied on a LOS event, before the SAToP instance transmits all 1s pattern downstream (AIS). Range 0 to 3 seconds in 100 millisecond increments.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3AisStabilizationProfileExitTime		1.3.6.1.4.1.2544.1.12.19.1.5.1.3
This object allows SNMP management entities to specify the holdon time that will be applied when leaving the AIS Stabilization period. Range 0 to 3 seconds in 100 milliseconds increments (e.g. parameter range is 0 to 30).
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3SatopTable		1.3.6.1.4.1.2544.1.12.19.1.6
A list of entries corresponding to the PWE3 SAToP entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		F3Pwe3SatopEntry

f3Pwe3SatopEntry		1.3.6.1.4.1.2544.1.12.19.1.6.1
An entry containing information applicable to a particular PWE3 SAToP Entity.
Status: current	Access: not-accessible
OBJECT-TYPE
	F3Pwe3SatopEntry

f3Pwe3SatopIndex		1.3.6.1.4.1.2544.1.12.19.1.6.1.1
Unique index value associated with the SAToP Entity.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

f3Pwe3SatopAlias		1.3.6.1.4.1.2544.1.12.19.1.6.1.2
This object allows SNMP management entities to provide an alias to the PWE3 SAToP entity.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..256)

f3Pwe3SatopAdminState		1.3.6.1.4.1.2544.1.12.19.1.6.1.3
This object represents the Administrative State of the PWE3 SAToP entity.
Status: current	Access: read-write
OBJECT-TYPE
	AdminState

f3Pwe3SatopOperationalState		1.3.6.1.4.1.2544.1.12.19.1.6.1.4
This object represents the Operational State of the PWE3 SAToP entity.
Status: current	Access: read-only
OBJECT-TYPE
	OperationalState

f3Pwe3SatopSecondaryState		1.3.6.1.4.1.2544.1.12.19.1.6.1.5
This object represents the Secondary State of the PWE3 SAToP entity.
Status: current	Access: read-only
OBJECT-TYPE
	SecondaryState

f3Pwe3SatopTDMEntity		1.3.6.1.4.1.2544.1.12.19.1.6.1.6
This object allows specification of the T1/E1 entity associated with the SAToP. This is only used at SATop creation time. Result of get operation on this object will result with zeroDotZero since one Satop could have more then one associated TDM entity. Subsequently, the associated TDM entities are managed via f3Pwe3SatopTDMEntityTable.
Status: current	Access: read-create
OBJECT-TYPE
	VariablePointer

f3Pwe3SatopDiscoveryType		1.3.6.1.4.1.2544.1.12.19.1.6.1.7
This object allows ability to statically/dynamically determine the MAC address of the remote IP Address associated with the SAToP. In the case of static discovery type, f3Pwe3SatopRemoteMacAddress must be explicitly specified. In the case of dynamic discovery, the system will use ARP mechanism to obtain the remote Layer 2 MAC address.
Status: current	Access: read-create
OBJECT-TYPE
	PWE3SatopDiscoveryType

f3Pwe3SatopRemoteIpAddress		1.3.6.1.4.1.2544.1.12.19.1.6.1.8
This object allows ability to specify the remote IP Address. This is used in the PWE payload.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

f3Pwe3SatopRemoteMacAddress		1.3.6.1.4.1.2544.1.12.19.1.6.1.9
This object allows ability to specify the remote Layer 2 MAC Address. This must be specified in case of f3Pwe3SatopDiscoveryType as static. This is derived dynamically (via ARP) if f3Pwe3SatopDiscoveryType is dynamic, i.e. it does not have to be specified.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

f3Pwe3SatopEncapsulationType		1.3.6.1.4.1.2544.1.12.19.1.6.1.10
This object allows ability to specify the encapsulation type of the SATop. It can be encapsulated with VLAN and single MPLS label(vlan-one-mpls-label), VLAN and two MPLS labels (vlan-two-mpls-label), untagged and two MPLS labels (novlan-two-mpls-label) .
Status: current	Access: read-create
OBJECT-TYPE
	PWE3SatopEncapsulationType

f3Pwe3SatopRTPEnabled		1.3.6.1.4.1.2544.1.12.19.1.6.1.11
This object enables/disables RTP header for this SATop instance.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

f3Pwe3SatopRTPUpdateFrequency		1.3.6.1.4.1.2544.1.12.19.1.6.1.12
When f3Pwe3SatopRTPEnabled is true, this object allows specification of the RTP clock update frequency.
Status: current	Access: read-create
OBJECT-TYPE
	PWE3SatopRTPTSUpdateFreqType

f3Pwe3SatopControlWordEnabled		1.3.6.1.4.1.2544.1.12.19.1.6.1.13
This object is used for 3rd party interoperability, since earlier versions of PWE do not support control-word.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

f3Pwe3SatopJitterBufferSize		1.3.6.1.4.1.2544.1.12.19.1.6.1.14
This object allows definition of size of the jitter buffer in microseconds for this SATop instance.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

f3Pwe3SatopPayloadSize		1.3.6.1.4.1.2544.1.12.19.1.6.1.15
This object allows specification of the SATop payload size.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

f3Pwe3SatopVlanId		1.3.6.1.4.1.2544.1.12.19.1.6.1.16
This object allows specification of the SATop VLAN Id. Applicable for vlan based encapsulation types.
Status: current	Access: read-create
OBJECT-TYPE
	VlanId

f3Pwe3SatopVlanPriority		1.3.6.1.4.1.2544.1.12.19.1.6.1.17
This object allows specification of the SATop VLAN Priority. Applicable for vlan based encapsulation types.
Status: current	Access: read-create
OBJECT-TYPE
	VlanPriority

f3Pwe3SatopRxMplsLabel1		1.3.6.1.4.1.2544.1.12.19.1.6.1.18
This object allows specification of the expected receive MPLS Label. Applicable for single MPLS label encapsulation type.
Status: current	Access: read-create
OBJECT-TYPE
	MplsLabel

f3Pwe3SatopRxMplsLabel2		1.3.6.1.4.1.2544.1.12.19.1.6.1.19
This object allows specification of the expected receive MPLS Label. Applicable for dual MPLS label encapsulation types.
Status: current	Access: read-create
OBJECT-TYPE
	MplsLabel

f3Pwe3SatopTxMplsLabel1		1.3.6.1.4.1.2544.1.12.19.1.6.1.20
This object allows specification of the transmitted MPLS Label, used for multiplexing. Applicable for single MPLS label encapsulation type.
Status: current	Access: read-create
OBJECT-TYPE
	MplsLabel

f3Pwe3SatopTxMplsLabel2		1.3.6.1.4.1.2544.1.12.19.1.6.1.21
This object allows specification of the transmitted MPLS Label, used for multiplexing. Applicable for dual MPLS label encapsulation type.
Status: current	Access: read-create
OBJECT-TYPE
	MplsLabel

f3Pwe3SatopAisStabilizationProfile		1.3.6.1.4.1.2544.1.12.19.1.6.1.22
This object allows specification of the AIS stabilization Profile object. If no profile is associated, this value should be 0.0.
Status: current	Access: read-create
OBJECT-TYPE
	VariablePointer

f3Pwe3SatopResyncProfile		1.3.6.1.4.1.2544.1.12.19.1.6.1.23
This object allows specification of the Resync Profile object. If no profile is associated, this value should be 0.0.
Status: current	Access: read-create
OBJECT-TYPE
	VariablePointer

f3Pwe3SatopLossProfile		1.3.6.1.4.1.2544.1.12.19.1.6.1.24
This object allows specification of the Loss Profile object. If no profile is associated, this value should be 0.0.
Status: current	Access: read-create
OBJECT-TYPE
	VariablePointer

f3Pwe3SatopTransportMode		1.3.6.1.4.1.2544.1.12.19.1.6.1.25
This object allows specification of the SATop transport mode.
Status: current	Access: read-create
OBJECT-TYPE
	PWE3SatopTransportMode

f3Pwe3SatopStorageType		1.3.6.1.4.1.2544.1.12.19.1.6.1.26
The type of storage configured for this entry.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

f3Pwe3SatopRowStatus		1.3.6.1.4.1.2544.1.12.19.1.6.1.27
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3Pwe3SatopRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3Pwe3SatopRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3Pwe3SatopRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

f3Pwe3SatopTDMEntitiesTable		1.3.6.1.4.1.2544.1.12.19.1.7
A list of entries corresponding to the PWE3 SATop TDM entities .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		F3Pwe3SatopTDMEntitiesEntry

f3Pwe3SatopTDMEntitiesEntry		1.3.6.1.4.1.2544.1.12.19.1.7.1
An entry containing information applicable to a particular PWE3 SATop TDM entity.
Status: current	Access: not-accessible
OBJECT-TYPE
	F3Pwe3SatopTDMEntitiesEntry

f3Pwe3SatopTDMEntityIndex		1.3.6.1.4.1.2544.1.12.19.1.7.1.1
Unique index value associated with the PWE3 SATOP TDM Entity.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

f3Pwe3SatopTDMEntityObject		1.3.6.1.4.1.2544.1.12.19.1.7.1.2
This object points to the PWE3 SATOP TDM Entity. This is OID of the actual T1/E1 interface.
Status: current	Access: read-write
OBJECT-TYPE
	VariablePointer

f3Pwe3SatopTDMEntityStorageType		1.3.6.1.4.1.2544.1.12.19.1.7.1.3
The type of storage configured for this entry.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

f3Pwe3SatopTDMEntityRowStatus		1.3.6.1.4.1.2544.1.12.19.1.7.1.4
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3Pwe3SatopTDMEntityRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3Pwe3SatopTDMEntityRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3Pwe3SatopTDMEntityRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

f3Pwe3SatopStatsTable		1.3.6.1.4.1.2544.1.12.19.2.1
The PWE3 SATop Current data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		F3Pwe3SatopStatsEntry

f3Pwe3SatopStatsEntry		1.3.6.1.4.1.2544.1.12.19.2.1.1
A conceptual row in the f3Pwe3SatopStatsTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	F3Pwe3SatopStatsEntry

f3Pwe3SatopStatsIndex		1.3.6.1.4.1.2544.1.12.19.2.1.1.1
An index of the SATop current bin.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

f3Pwe3SatopStatsIntervalType		1.3.6.1.4.1.2544.1.12.19.2.1.1.2
Indicates the type of collection, i.e. whether it is 15 Min, 1 Day.
Status: current	Access: read-only
OBJECT-TYPE
	CmPmIntervalType

f3Pwe3SatopStatsValid		1.3.6.1.4.1.2544.1.12.19.2.1.1.3
Indicates the validity of the bin.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

f3Pwe3SatopStatsAction		1.3.6.1.4.1.2544.1.12.19.2.1.1.4
Allows the Manager to clear the bin.
Status: current	Access: read-write
OBJECT-TYPE
	CmPmBinAction

f3Pwe3SatopStatsESs		1.3.6.1.4.1.2544.1.12.19.2.1.1.5
The counter associated with the number of Errored Seconds encountered by the SATop in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopStatsSESs		1.3.6.1.4.1.2544.1.12.19.2.1.1.6
The counter associated with the number of Severely Errored Seconds encountered by the SATop in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopStatsEBs		1.3.6.1.4.1.2544.1.12.19.2.1.1.7
The counter associated with the number of Errored Blocsk encountered by the SATop in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopStatsResyncs		1.3.6.1.4.1.2544.1.12.19.2.1.1.8
The counter associated with the number of Resync count events encountered by the SATop in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopStatsMaxJitter		1.3.6.1.4.1.2544.1.12.19.2.1.1.9
The maximum absolute jitter on SATop in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

f3Pwe3SatopStatsFramesTx		1.3.6.1.4.1.2544.1.12.19.2.1.1.10
The counter associated with the number of Frames Transmitted in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopStatsPayloadOctetsTx		1.3.6.1.4.1.2544.1.12.19.2.1.1.11
The counter associated with the number of Payload Octets Transmitted in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopStatsFramesRx		1.3.6.1.4.1.2544.1.12.19.2.1.1.12
The counter associated with the number of Frames Received in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopStatsPayloadOctetsRx		1.3.6.1.4.1.2544.1.12.19.2.1.1.13
The counter associated with the number of Payload Octets Received in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopStatsOutOfSeqFramesRx		1.3.6.1.4.1.2544.1.12.19.2.1.1.14
The counter associated with the number of Out of Sequence Frames Received in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopStatsLostFrames		1.3.6.1.4.1.2544.1.12.19.2.1.1.15
The counter associated with the number of Lost Frames detected in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopStatsLostFramesStateTrans		1.3.6.1.4.1.2544.1.12.19.2.1.1.16
The counter associated with the number of transitions to Lost Frame State detected in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopStatsMalformedFramesRx		1.3.6.1.4.1.2544.1.12.19.2.1.1.17
The counter associated with the number of Malformed Frames received in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopStatsJitterBufferLateFrames		1.3.6.1.4.1.2544.1.12.19.2.1.1.18
The counter associated with the number of Jitter Buffer Late Frames in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopHistoryTable		1.3.6.1.4.1.2544.1.12.19.2.2
The PWE3 SATop History data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		F3Pwe3SatopHistoryEntry

f3Pwe3SatopHistoryEntry		1.3.6.1.4.1.2544.1.12.19.2.2.1
A conceptual row in the f3Pwe3SatopHistoryTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	F3Pwe3SatopHistoryEntry

f3Pwe3SatopHistoryIndex		1.3.6.1.4.1.2544.1.12.19.2.2.1.1
An index of the SATop current bin.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

f3Pwe3SatopHistoryTime		1.3.6.1.4.1.2544.1.12.19.2.2.1.2
Indicates the time of history bin creation.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

f3Pwe3SatopHistoryValid		1.3.6.1.4.1.2544.1.12.19.2.2.1.3
Indicates the validity of the bin.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

f3Pwe3SatopHistoryAction		1.3.6.1.4.1.2544.1.12.19.2.2.1.4
Allows the Manager to clear the bin.
Status: current	Access: read-write
OBJECT-TYPE
	CmPmBinAction

f3Pwe3SatopHistoryESs		1.3.6.1.4.1.2544.1.12.19.2.2.1.5
The counter associated with the number of Errored Seconds encountered by the SATop in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopHistorySESs		1.3.6.1.4.1.2544.1.12.19.2.2.1.6
The counter associated with the number of Severely Errored Seconds encountered by the SATop in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopHistoryEBs		1.3.6.1.4.1.2544.1.12.19.2.2.1.7
The counter associated with the number of Errored Blocsk encountered by the SATop in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopHistoryResyncs		1.3.6.1.4.1.2544.1.12.19.2.2.1.8
The counter associated with the number of Resync count events encountered by the SATop in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopHistoryMaxJitter		1.3.6.1.4.1.2544.1.12.19.2.2.1.9
The maximum absolute jitter on SATop in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

f3Pwe3SatopHistoryFramesTx		1.3.6.1.4.1.2544.1.12.19.2.2.1.10
The counter associated with the number of Frames Transmitted in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopHistoryPayloadOctetsTx		1.3.6.1.4.1.2544.1.12.19.2.2.1.11
The counter associated with the number of Payload Octets Transmitted in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopHistoryFramesRx		1.3.6.1.4.1.2544.1.12.19.2.2.1.12
The counter associated with the number of Frames Received in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopHistoryPayloadOctetsRx		1.3.6.1.4.1.2544.1.12.19.2.2.1.13
The counter associated with the number of Payload Octets Received in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopHistoryOutOfSeqFramesRx		1.3.6.1.4.1.2544.1.12.19.2.2.1.14
The counter associated with the number of Out of Sequence Frames Received in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopHistoryLostFrames		1.3.6.1.4.1.2544.1.12.19.2.2.1.15
The counter associated with the number of Lost Frames detected in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopHistoryLostFramesStateTrans		1.3.6.1.4.1.2544.1.12.19.2.2.1.16
The counter associated with the number of transitions to Lost Frame State detected in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopHistoryMalformedFramesRx		1.3.6.1.4.1.2544.1.12.19.2.2.1.17
The counter associated with the number of Malformed Frames received in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopHistoryJitterBufferLateFrames		1.3.6.1.4.1.2544.1.12.19.2.2.1.18
The counter associated with the number of Jitter Buffer Overruns in the current bin.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3Pwe3SatopThresholdTable		1.3.6.1.4.1.2544.1.12.19.2.3
A table of entries that allow manageability of SATop Thresholds.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		F3Pwe3SatopThresholdEntry

f3Pwe3SatopThresholdEntry		1.3.6.1.4.1.2544.1.12.19.2.3.1
A conceptual row in the f3Pwe3SatopThresholdTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	F3Pwe3SatopThresholdEntry

f3Pwe3SatopThresholdIndex		1.3.6.1.4.1.2544.1.12.19.2.3.1.1
An index that uniquely identifies an entry in the f3Pwe3SatopThresholdTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

f3Pwe3SatopThresholdInterval		1.3.6.1.4.1.2544.1.12.19.2.3.1.2
The interval over which monitored value is sampled and compared with the specified threshold.
Status: current	Access: read-only
OBJECT-TYPE
	CmPmIntervalType

f3Pwe3SatopThresholdVariable		1.3.6.1.4.1.2544.1.12.19.2.3.1.3
The object identifier of the particular variable to be sampled.
Status: current	Access: read-only
OBJECT-TYPE
	VariablePointer

f3Pwe3SatopThresholdValueLo		1.3.6.1.4.1.2544.1.12.19.2.3.1.4
Lower 32 bits of the threshold value.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3SatopThresholdValueHi		1.3.6.1.4.1.2544.1.12.19.2.3.1.5
Higher 32 bits of the threshold value.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

f3Pwe3SatopThresholdMonValue		1.3.6.1.4.1.2544.1.12.19.2.3.1.6
Monitored value corresponding to f3Pwe3SatopThresholdVariable.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

f3Pwe3SatopThresholdCrossingAlert		1.3.6.1.4.1.2544.1.12.19.3.1
This trap is sent each time a threshold on a PM condition on an PWE3 SATop is crossed.
Status: current	Access: read-only
NOTIFICATION-TYPE

f3Pwe3Compliances		1.3.6.1.4.1.2544.1.12.19.4.1
OBJECT IDENTIFIER

f3Pwe3Groups		1.3.6.1.4.1.2544.1.12.19.4.2
OBJECT IDENTIFIER

f3Pwe3Compliance		1.3.6.1.4.1.2544.1.12.19.4.1.1
Describes the requirements for conformance to the F3 PWE3 group.
Status: current	Access: read-only
MODULE-COMPLIANCE

f3Pwe3ObjectGroup		1.3.6.1.4.1.2544.1.12.19.4.2.1
A collection of objects used to manage the F3 PWE3 Configuration data.
Status: current	Access: read-only
OBJECT-GROUP

f3Pwe3PerfObjectGroup		1.3.6.1.4.1.2544.1.12.19.4.2.2
A collection of objects used to manage the F3 PWE3 Performance data.
Status: current	Access: read-only
OBJECT-GROUP

f3Pwe3PerfNotifGroup		1.3.6.1.4.1.2544.1.12.19.4.2.3
A collection of notifications related to F3 PWE3 Threshold Crossing Alerts.
Status: current	Access: read-only
NOTIFICATION-GROUP