EdgeSwitch-ROUTING-MIB

File: EdgeSwitch-ROUTING-MIB.mib (146815 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC EdgeSwitch-REF-MIB
RFC1213-MIB OSPF-MIB RIPv2-MIB
VRRP-MIB IF-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
IpAddress Integer32 TimeTicks
Gauge32 Unsigned32 Counter32
RowStatus TruthValue TEXTUAL-CONVENTION
fastPath DisplayString PhysAddress
ospfIfEntry ospfVirtIfEntry ospfAreaEntry
RouterID rip2IfConfEntry vrrpOperVrId
ifIndex InterfaceIndex InterfaceIndexOrZero

Defined Types

SpfTimerRange  
The range of intervals on which Spf timers can be configured.
TEXTUAL-CONVENTION    
  Integer32 0..65535  

AutoCostRefBw  
The value of reference bandwidth from which ospf calculates metric cost.
TEXTUAL-CONVENTION    
  Unsigned32 1..4294967  

AgentSwitchArpEntry  
SEQUENCE    
  agentSwitchArpAge TimeTicks
  agentSwitchArpIpAddress IpAddress
  agentSwitchArpMacAddress PhysAddress
  agentSwitchArpInterface Integer32
  agentSwitchArpType INTEGER
  agentSwitchArpStatus RowStatus

AgentSwitchLocalProxyArpEntry  
SEQUENCE    
  agentSwitchLocalProxyArpMode INTEGER

AgentSwitchIntfArpEntry  
SEQUENCE    
  agentSwitchIntfArpIpAddress IpAddress
  agentSwitchIntfArpIfIndex InterfaceIndex
  agentSwitchIntfArpAge TimeTicks
  agentSwitchIntfArpMacAddress PhysAddress
  agentSwitchIntfArpType INTEGER
  agentSwitchIntfArpStatus RowStatus

AgentSwitchIpInterfaceEntry  
SEQUENCE    
  agentSwitchIpInterfaceIfIndex Integer32
  agentSwitchIPAddressConfigMethod INTEGER
  agentSwitchIpInterfaceIpAddress IpAddress
  agentSwitchIpInterfaceNetMask IpAddress
  agentSwitchIpInterfaceClearIp INTEGER
  agentSwitchIpInterfaceRoutingMode INTEGER
  agentSwitchIpInterfaceProxyARPMode INTEGER
  agentSwitchIpInterfaceMtuValue Unsigned32
  agentSwitchIpInterfaceBandwidth Unsigned32
  agentSwitchIpInterfaceUnnumberedIfIndex InterfaceIndexOrZero
  agentSwitchIpInterfaceIcmpUnreachables INTEGER
  agentSwitchIpInterfaceIcmpRedirects INTEGER
  agentSwitchDhcpOperation INTEGER
  agentSwitchIpInterfaceSuppressed INTEGER
  agentSwitchIpInterfaceNumberOfFlaps Unsigned32
  agentSwitchIpInterfaceCurrentPenalty Unsigned32
  agentSwitchIpInterfaceReUseTime Unsigned32

AgentSwitchIpRouterDiscoveryEntry  
SEQUENCE    
  agentSwitchIpRouterDiscoveryIfIndex Integer32
  agentSwitchIpRouterDiscoveryAdvertiseMode INTEGER
  agentSwitchIpRouterDiscoveryMaxAdvertisementInterval Integer32
  agentSwitchIpRouterDiscoveryMinAdvertisementInterval Integer32
  agentSwitchIpRouterDiscoveryAdvertisementLifetime Integer32
  agentSwitchIpRouterDiscoveryPreferenceLevel Integer32
  agentSwitchIpRouterDiscoveryAdvertisementAddress IpAddress

AgentSwitchIpVlanEntry  
SEQUENCE    
  agentSwitchIpVlanId Integer32
  agentSwitchIpVlanIfIndex Integer32
  agentSwitchIpVlanRoutingStatus RowStatus

AgentSwitchSecondaryAddressEntry  
SEQUENCE    
  agentSwitchSecondaryIpAddress IpAddress
  agentSwitchSecondaryNetMask IpAddress
  agentSwitchSecondaryStatus RowStatus

AgentSwitchHelperAddressEntry  
SEQUENCE    
  agentSwitchHelperIpAddress IpAddress
  agentSwitchHelperStatus RowStatus

AgentSwitchIntfIpHelperAddressEntry  
SEQUENCE    
  agentSwitchIntfIpHelperIpAddress IpAddress
  agentSwitchIntfIpHelperUdpPort Unsigned32
  agentSwitchIntfIpHelperDiscard TruthValue
  agentSwitchIntfIpHelperHitCount Unsigned32
  agentSwitchIntfIpHelperStatus RowStatus

AgentRipRouteRedistEntry  
SEQUENCE    
  agentRipRouteRedistSource INTEGER
  agentRipRouteRedistMode INTEGER
  agentRipRouteRedistMetric Integer32
  agentRipRouteRedistMetricConfigured TruthValue
  agentRipRouteRedistMatchInternal INTEGER
  agentRipRouteRedistMatchExternal1 INTEGER
  agentRipRouteRedistMatchExternal2 INTEGER
  agentRipRouteRedistMatchNSSAExternal1 INTEGER
  agentRipRouteRedistMatchNSSAExternal2 INTEGER
  agentRipRouteRedistDistList Unsigned32
  agentRipRouteRedistDistListConfigured TruthValue

AgentRip2IfConfEntry  
SEQUENCE    
  agentRip2IfConfAuthKeyId INTEGER

AgentOspfRouteRedistEntry  
SEQUENCE    
  agentOspfRouteRedistSource INTEGER
  agentOspfRouteRedistMode INTEGER
  agentOspfRouteRedistMetric Integer32
  agentOspfRouteRedistMetricConfigured TruthValue
  agentOspfRouteRedistMetricType INTEGER
  agentOspfRouteRedistTag Unsigned32
  agentOspfRouteRedistSubnets TruthValue
  agentOspfRouteRedistDistList Unsigned32
  agentOspfRouteRedistDistListConfigured TruthValue

AgentOspfIfEntry  
SEQUENCE    
  agentOspfIfAuthKeyId INTEGER
  agentOspfIfIpMtuIgnoreFlag INTEGER
  agentOspfIfPassiveMode TruthValue
  agentOspfIfAdvertiseSecondaries INTEGER

AgentOspfVirtIfEntry  
SEQUENCE    
  agentOspfVirtIfAuthKeyId INTEGER

AgentOspfAreaOpaqueLsdbEntry  
SEQUENCE    
  agentOspfAreaOpaqueLsdbAreaId IpAddress
  agentOspfAreaOpaqueLsdbType INTEGER
  agentOspfAreaOpaqueLsdbLsid IpAddress
  agentOspfAreaOpaqueLsdbRouterId IpAddress
  agentOspfAreaOpaqueLsdbSequence Integer32
  agentOspfAreaOpaqueLsdbAge Integer32
  agentOspfAreaOpaqueLsdbChecksum Integer32
  agentOspfAreaOpaqueLsdbAdvertisement OCTET STRING

AgentOspfLocalLsdbEntry  
SEQUENCE    
  agentOspfLocalLsdbIpAddress IpAddress
  agentOspfLocalLsdbAddressLessIf InterfaceIndexOrZero
  agentOspfLocalLsdbType INTEGER
  agentOspfLocalLsdbLsid IpAddress
  agentOspfLocalLsdbRouterId RouterID
  agentOspfLocalLsdbSequence Integer32
  agentOspfLocalLsdbAge Integer32
  agentOspfLocalLsdbChecksum Integer32
  agentOspfLocalLsdbAdvertisement OCTET STRING

AgentOspfAsLsdbEntry  
SEQUENCE    
  agentOspfAsLsdbType INTEGER
  agentOspfAsLsdbLsid IpAddress
  agentOspfAsLsdbRouterId RouterID
  agentOspfAsLsdbSequence Integer32
  agentOspfAsLsdbAge Integer32
  agentOspfAsLsdbChecksum Integer32
  agentOspfAsLsdbAdvertisement OCTET STRING

AgentRouterVrrpConfiguredEntry  
SEQUENCE    
  agentRouterVrrpConfiguredPriority Integer32

AgentRouterVrrpOperEntry  
SEQUENCE    
  agentRouterVrrpOperPriority Integer32

AgentRouterVrrpTrackIntfEntry  
SEQUENCE    
  agentRouterVrrpTrackIntf InterfaceIndex
  agentRouterVrrpTrackIfPrioDec Integer32
  agentRouterVrrpTrackIfState TruthValue
  agentRouterVrrpTrackIfStatus RowStatus

AgentRouterVrrpTrackRouteEntry  
SEQUENCE    
  agentRouterVrrpTrackRtPfx IpAddress
  agentRouterVrrpTrackRtPfxLen Integer32
  agentRouterVrrpTrackRtPrioDec Integer32
  agentRouterVrrpTrackRtReachable TruthValue
  agentRouterVrrpTrackRtStatus RowStatus

AgentSwitchIpHelperAddressEntry  
SEQUENCE    
  agentSwitchIpHelperAddress IpAddress
  agentSwitchIpHelperUdpPort Unsigned32
  agentSwitchIpHelperHitCount Unsigned32
  agentSwitchIpHelperStatus RowStatus

AgentSwitchInternalVlanEntry  
SEQUENCE    
  agentSwitchInternalVlanId Integer32
  agentSwitchInternalVlanIfIndex Integer32

AgentOspfQueueEntry  
SEQUENCE    
  agentOspfQueueIndex Unsigned32
  agentOspfQueueName DisplayString
  agentOspfQueueLength Gauge32
  agentOspfQueueHigh Gauge32
  agentOspfQueueDrops Counter32
  agentOspfQueueLimit Unsigned32

AgentOspfSpfStatsEntry  
SEQUENCE    
  agentOspfSpfIndex Counter32
  agentOspfSpfStatsDeltaT Unsigned32
  agentOspfSpfStatsIntra Gauge32
  agentOspfSpfStatsSumm Gauge32
  agentOspfSpfStatsExt Gauge32
  agentOspfSpfStatsSpfTotal Gauge32
  agentOspfSpfStatsRibUpdate Gauge32
  agentOspfSpfStatsReason DisplayString

AgentEcmpCountEntry  
SEQUENCE    
  agentEcmpNextHopCount Unsigned32
  agentEcmpRouteCount Gauge32

Defined Values

fastPathRouting 1.3.6.1.4.1.4413.1.1.2
The Ubiquiti Private MIB for FastPath Routing
MODULE-IDENTITY    

agentSwitchArpGroup 1.3.6.1.4.1.4413.1.1.2.1
OBJECT IDENTIFIER    

agentSwitchArpAgeoutTime 1.3.6.1.4.1.4413.1.1.2.1.1
Configures the ARP entry ageout time in seconds. Allowable range: 15-21600
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 15..21600  

agentSwitchArpResponseTime 1.3.6.1.4.1.4413.1.1.2.1.2
Configures the ARP request response timeout in seconds. Allowable range: 1-10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..10  

agentSwitchArpMaxRetries 1.3.6.1.4.1.4413.1.1.2.1.3
Configures the ARP count of maximum request for retries. Allowable range: 0-10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10  

agentSwitchArpCacheSize 1.3.6.1.4.1.4413.1.1.2.1.4
Configures the ARP maximum number of entries in the cache. Allowable range is platform-specific.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

agentSwitchArpDynamicRenew 1.3.6.1.4.1.4413.1.1.2.1.5
This indicates the current setting of ARP dynamic renew mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchArpTotalEntryCountCurrent 1.3.6.1.4.1.4413.1.1.2.1.6
Current number of entries in the ARP cache.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentSwitchArpTotalEntryCountPeak 1.3.6.1.4.1.4413.1.1.2.1.7
Peak number of entries recorded in the ARP cache over time. This value is restarted whenever the ARP cache size is changed.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentSwitchArpStaticEntryCountCurrent 1.3.6.1.4.1.4413.1.1.2.1.8
Current number of configured static ARP entries.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentSwitchArpStaticEntryCountMax 1.3.6.1.4.1.4413.1.1.2.1.9
Maximum number of configurable static ARP entries.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentSwitchArpTable 1.3.6.1.4.1.4413.1.1.2.1.10
This table augments the MIB-II ipNetToMediaTable by providing per-interface ARP entry information.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchArpEntry

agentSwitchArpEntry 1.3.6.1.4.1.4413.1.1.2.1.10.1
Tok_String
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  AgentSwitchArpEntry  

agentSwitchArpAge 1.3.6.1.4.1.4413.1.1.2.1.10.1.1
This defines the time (in seconds) since the ARP entry was last refreshed. This value is 0 for ARP entries of type local(1) or static(3), since these entries are not subject to aging.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TimeTicks  

agentSwitchArpIpAddress 1.3.6.1.4.1.4413.1.1.2.1.10.1.2
The IP Address assigned to each interface.
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

agentSwitchArpMacAddress 1.3.6.1.4.1.4413.1.1.2.1.10.1.3
The hardware MAX Address that each interface maps to.
Status: obsolete Access: read-create
OBJECT-TYPE    
  PhysAddress  

agentSwitchArpInterface 1.3.6.1.4.1.4413.1.1.2.1.10.1.4
The Associated IfIndex which identified the ARP Entry.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32  

agentSwitchArpType 1.3.6.1.4.1.4413.1.1.2.1.10.1.5
The type of ARP entry.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER local(1), gateway(2), static(3), dynamic(4)  

agentSwitchArpStatus 1.3.6.1.4.1.4413.1.1.2.1.10.1.6
The status of this ARP entry. Setting this object destroy will remove the entry.
Status: obsolete Access: read-write
OBJECT-TYPE    
  RowStatus  

agentSwitchLocalProxyArpTable 1.3.6.1.4.1.4413.1.1.2.1.11
This table contains the per-interface configuration parameters for Local Proxy Arp.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchLocalProxyArpEntry

agentSwitchLocalProxyArpEntry 1.3.6.1.4.1.4413.1.1.2.1.11.1
Represents a logical row in the agentSwitchLocalProxyArpTable
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentSwitchLocalProxyArpEntry  

agentSwitchLocalProxyArpMode 1.3.6.1.4.1.4413.1.1.2.1.11.1.1
The Local Proxy Arp Mode for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchIntfArpTable 1.3.6.1.4.1.4413.1.1.2.1.12
This table augments the MIB-II ipNetToMediaTable by providing per-interface ARP entry information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchIntfArpEntry

agentSwitchIntfArpEntry 1.3.6.1.4.1.4413.1.1.2.1.12.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentSwitchIntfArpEntry  

agentSwitchIntfArpIpAddress 1.3.6.1.4.1.4413.1.1.2.1.12.1.1
The Type of Address assigned to this interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

agentSwitchIntfArpIfIndex 1.3.6.1.4.1.4413.1.1.2.1.12.1.2
The Associated IfIndex which identified the ARP Entry. This value must be specified for static ARP entries on an unnumbered interface
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

agentSwitchIntfArpAge 1.3.6.1.4.1.4413.1.1.2.1.12.1.3
This defines the time (in seconds) since the ARP entry was last refreshed. This value is 0 for ARP entries of type local(1) or static(3), since these entries are not subject to aging.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

agentSwitchIntfArpMacAddress 1.3.6.1.4.1.4413.1.1.2.1.12.1.4
The hardware MAX Address that each interface maps to.
Status: current Access: read-create
OBJECT-TYPE    
  PhysAddress  

agentSwitchIntfArpType 1.3.6.1.4.1.4413.1.1.2.1.12.1.5
The type of ARP entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER local(1), gateway(2), static(3), dynamic(4)  

agentSwitchIntfArpStatus 1.3.6.1.4.1.4413.1.1.2.1.12.1.6
The status of this ARP entry. Setting this object destroy will remove the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

agentSwitchIpGroup 1.3.6.1.4.1.4413.1.1.2.2
OBJECT IDENTIFIER    

agentSwitchIpRoutingMode 1.3.6.1.4.1.4413.1.1.2.2.1
Administratively enables/disables routing on the switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchIpDefaultGateway 1.3.6.1.4.1.4413.1.1.2.2.2
Specifies the Default Gateway manually configured.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

agentSwitchIpInterfaceTable 1.3.6.1.4.1.4413.1.1.2.2.3
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchIpInterfaceEntry

agentSwitchIpInterfaceEntry 1.3.6.1.4.1.4413.1.1.2.2.3.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentSwitchIpInterfaceEntry  

agentSwitchIpInterfaceIfIndex 1.3.6.1.4.1.4413.1.1.2.2.3.1.1
The IfIndex associated with this instance.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

agentSwitchIPAddressConfigMethod 1.3.6.1.4.1.4413.1.1.2.2.3.1.2
The Source of the IP Address. User can set the object to none(0) or dhcp(2). Option dhcp(2) enables Dhcp Client on the interface. Option none(0) disables Dhcp Client on the interface. Get on this object returns manual(1) only when the interface has a manually configured address.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), manual(1), dhcp(2)  

agentSwitchIpInterfaceIpAddress 1.3.6.1.4.1.4413.1.1.2.2.3.1.3
The IpAddress assigned to this interface. When setting this value, the value of agentSwitchIpInterfaceNetMask must be set at the same time.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

agentSwitchIpInterfaceNetMask 1.3.6.1.4.1.4413.1.1.2.2.3.1.4
The NetMask assigned to this interface. When setting this value, the value of agentSwitchIpInterfaceIpAddress must be set at the same time.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

agentSwitchIpInterfaceClearIp 1.3.6.1.4.1.4413.1.1.2.2.3.1.5
Sets the interfaces IpAddress and NetMask back to 0.0.0.0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchIpInterfaceRoutingMode 1.3.6.1.4.1.4413.1.1.2.2.3.1.6
Enables or disables routing for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchIpInterfaceProxyARPMode 1.3.6.1.4.1.4413.1.1.2.2.3.1.7
Enables or disables Proxy ARP for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchIpInterfaceMtuValue 1.3.6.1.4.1.4413.1.1.2.2.3.1.8
Configures the MTU value for this interface. The applicable range is 68 to the , in bytes. Get of this object returns the effective MTU value on the interface. Set of this object with a value of 0 resets the MTU to the default IP MTU value on the interface.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 68..9198  

agentSwitchIpInterfaceBandwidth 1.3.6.1.4.1.4413.1.1.2.2.3.1.9
Configures the Bandwidth value for this interface. If the value returned is 0 bandwidth for this interface is not Configured.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 1..10000000  

agentSwitchIpInterfaceUnnumberedIfIndex 1.3.6.1.4.1.4413.1.1.2.2.3.1.10
If this object is non-zero, it indicates that the interface is unnumbered, and specifies which interface the address is borrowed from.
Status: current Access: read-write
OBJECT-TYPE    
  InterfaceIndexOrZero  

agentSwitchIpInterfaceIcmpUnreachables 1.3.6.1.4.1.4413.1.1.2.2.3.1.11
If this object is enable, it indicates that ICMP unreachables can be sent on this interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchIpInterfaceIcmpRedirects 1.3.6.1.4.1.4413.1.1.2.2.3.1.12
If this object is enable and agentSwitchIpIcmpRedirectsMode is also enable ICMP Redirects can be sent on this interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchDhcpOperation 1.3.6.1.4.1.4413.1.1.2.2.3.1.13
Renew or Release the IP Address learned through DHCP. Get on this object always gives none. none means no operation is performed on dhcp.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER renew(1), release(2), none(3)  

agentSwitchIpInterfaceSuppressed 1.3.6.1.4.1.4413.1.1.2.2.3.1.14
This mib variable contains the following values, which has the meaning as: 'unsuppressed' - The interface is not suppressed 'suppressed' - The interface is suppressed
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unsuppressed(0), suppressed(1)  

agentSwitchIpInterfaceNumberOfFlaps 1.3.6.1.4.1.4413.1.1.2.2.3.1.15
This mib variable displays the number of flaps occurred on the interface
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

agentSwitchIpInterfaceCurrentPenalty 1.3.6.1.4.1.4413.1.1.2.2.3.1.16
This mib variable displays the current penalty of an interface
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..20000  

agentSwitchIpInterfaceReUseTime 1.3.6.1.4.1.4413.1.1.2.2.3.1.17
This mib variable displays the number of seconds until the interface is allowed to come up
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

agentSwitchIpRouterDiscoveryTable 1.3.6.1.4.1.4413.1.1.2.2.4
There is no global administrative flag for router discovery. The global routing flag (agentSwitchIpRoutingMode) will be used for this purpose. If routing is disabled, router discovery is disabled as well.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchIpRouterDiscoveryEntry

agentSwitchIpRouterDiscoveryEntry 1.3.6.1.4.1.4413.1.1.2.2.4.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentSwitchIpRouterDiscoveryEntry  

agentSwitchIpRouterDiscoveryIfIndex 1.3.6.1.4.1.4413.1.1.2.2.4.1.1
Interface Number to configure Router Discovery on.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

agentSwitchIpRouterDiscoveryAdvertiseMode 1.3.6.1.4.1.4413.1.1.2.2.4.1.2
Enable or disable router discovery on the interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchIpRouterDiscoveryMaxAdvertisementInterval 1.3.6.1.4.1.4413.1.1.2.2.4.1.3
Maximum time allowed between sending router advertisements from the interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..1800  

agentSwitchIpRouterDiscoveryMinAdvertisementInterval 1.3.6.1.4.1.4413.1.1.2.2.4.1.4
Minimum time allowed between sending router advertisements from the interface. This value must be less than or equal to agentSwitchIpRouterDiscoveryMaxAdvertisementInterval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..1800  

agentSwitchIpRouterDiscoveryAdvertisementLifetime 1.3.6.1.4.1.4413.1.1.2.2.4.1.5
Value of lifetime field of router advertsisement sent from the interface. This value must be greater than or equal to agentSwitchIpRouterDiscoveryMaxAdvertisementInterval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..9000  

agentSwitchIpRouterDiscoveryPreferenceLevel 1.3.6.1.4.1.4413.1.1.2.2.4.1.6
Preferability of the address as a default router address, related to other addresses on the same subnet. This is defined as the larger the number, the higher the preference.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

agentSwitchIpRouterDiscoveryAdvertisementAddress 1.3.6.1.4.1.4413.1.1.2.2.4.1.7
Address used when sending router advertisements from the interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

agentSwitchIpVlanTable 1.3.6.1.4.1.4413.1.1.2.2.5
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchIpVlanEntry

agentSwitchIpVlanEntry 1.3.6.1.4.1.4413.1.1.2.2.5.1
A Static VLAN for which routing can be enabled/disabled
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentSwitchIpVlanEntry  

agentSwitchIpVlanId 1.3.6.1.4.1.4413.1.1.2.2.5.1.1
The Vlan's Id.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

agentSwitchIpVlanIfIndex 1.3.6.1.4.1.4413.1.1.2.2.5.1.2
The IfIndex associated with this VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentSwitchIpVlanRoutingStatus 1.3.6.1.4.1.4413.1.1.2.2.5.1.3
Status of Routing mode per Vlan. active(1) - Vlan is enabled for routing createAndGo(4) - Adds Vlan entry for routing destroy(6) - Removes Vlan from routing
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

agentSwitchSecondaryAddressTable 1.3.6.1.4.1.4413.1.1.2.2.6
Contains a list of secondary IP Addresses associated with an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchSecondaryAddressEntry

agentSwitchSecondaryAddressEntry 1.3.6.1.4.1.4413.1.1.2.2.6.1
A secondary IP Address for a given interface. This IP Address must not conflict with the IP Address configured in the agentSwitchIpInterfaceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentSwitchSecondaryAddressEntry  

agentSwitchSecondaryIpAddress 1.3.6.1.4.1.4413.1.1.2.2.6.1.1
The Secondary IP Address assigned to this interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

agentSwitchSecondaryNetMask 1.3.6.1.4.1.4413.1.1.2.2.6.1.2
The Secondary Net Mask assigned to this interface. This value must be set during creation, and can not be changed.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

agentSwitchSecondaryStatus 1.3.6.1.4.1.4413.1.1.2.2.6.1.3
Creates a new entry in the Secondary Address table. Allowed values are: createAndGo(4) - Creates an entry in this table, associating the address with a given interface. The agentSwitchSecondaryNetMask object must be set during creation. destroy(6) - Removes the associated address from the interface.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

agentSwitchHelperAddressTable 1.3.6.1.4.1.4413.1.1.2.2.7
Replaced by agentSwitchIntfIpHelperAddressTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchHelperAddressEntry

agentSwitchHelperAddressEntry 1.3.6.1.4.1.4413.1.1.2.2.7.1
A Helper IP Address for a given interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  AgentSwitchHelperAddressEntry  

agentSwitchHelperIpAddress 1.3.6.1.4.1.4413.1.1.2.2.7.1.1
The Helper IP Address assigned to this interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  IpAddress  

agentSwitchHelperStatus 1.3.6.1.4.1.4413.1.1.2.2.7.1.2
Creates a new entry in the Helper Address table. Allowed values are: createAndGo(4) - Creates an entry in this table, associating the address with a given interface. The agentSwitchHelperNetMask object must be set during creation. destroy(6) - Removes the associated address from the interface.
Status: obsolete Access: read-create
OBJECT-TYPE    
  RowStatus  

agentSwitchIpIcmpControlGroup 1.3.6.1.4.1.4413.1.1.2.2.8
OBJECT IDENTIFIER    

agentSwitchIpIcmpEchoReplyMode 1.3.6.1.4.1.4413.1.1.2.2.8.1
Sets the administrative Echo Reply Mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchIpIcmpRedirectsMode 1.3.6.1.4.1.4413.1.1.2.2.8.2
Sets the administrative Mode for sending Redirects.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSwitchIpIcmpRateLimitInterval 1.3.6.1.4.1.4413.1.1.2.2.8.3
Specifies the time interval between tokens being placed in the bucket for ICMP Ratelimit.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..2147483647  

agentSwitchIpIcmpRateLimitBurstSize 1.3.6.1.4.1.4413.1.1.2.2.8.4
Specifies the number of tokens to be placed after timeout.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..200  

agentSwitchIntfIpHelperAddressTable 1.3.6.1.4.1.4413.1.1.2.2.10
Contains a list of IP helper addresses associated with an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchIntfIpHelperAddressEntry

agentSwitchIntfIpHelperAddressEntry 1.3.6.1.4.1.4413.1.1.2.2.10.1
An IP helper address for a given interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentSwitchIntfIpHelperAddressEntry  

agentSwitchIntfIpHelperIpAddress 1.3.6.1.4.1.4413.1.1.2.2.10.1.1
An IP helper address for packets received on this interface. An address of 0.0.0.0 identifies the entry as a discard entry. Packets that match a discard entry are dropped.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

agentSwitchIntfIpHelperUdpPort 1.3.6.1.4.1.4413.1.1.2.2.10.1.2
UDP port number. Received packets with this destination UDP port number are forwarded to the helper address in this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..65535  

agentSwitchIntfIpHelperDiscard 1.3.6.1.4.1.4413.1.1.2.2.10.1.3
Variable obsoleted. To create a discard entry, set the helper address to 0.0.0.0.
Status: obsolete Access: read-write
OBJECT-TYPE    
  TruthValue  

agentSwitchIntfIpHelperHitCount 1.3.6.1.4.1.4413.1.1.2.2.10.1.4
The number of times a packet has been forwarded or discarded according to this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentSwitchIntfIpHelperStatus 1.3.6.1.4.1.4413.1.1.2.2.10.1.5
Creates a new entry in the Helper Address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

agentSwitchClearIpDefaultGateway 1.3.6.1.4.1.4413.1.1.2.2.11
Resets the Global Default Gateway address.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentRouterRipConfigGroup 1.3.6.1.4.1.4413.1.1.2.3
OBJECT IDENTIFIER    

agentRouterRipAdminState 1.3.6.1.4.1.4413.1.1.2.3.1
Sets the administrative mode of RIP in the router.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentRouterRipSplitHorizonMode 1.3.6.1.4.1.4413.1.1.2.3.2
Sets the RIP split horizon operating mode in the router. A value of none(1) means split horizon processing is disabled. When set to simple(2), the simple split horizon technique is used. When set to poisonReverse(3), the split horizon with poison reverse technique is used. The default split horizon mode is simple(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), simple(2), poisonReverse(3)  

agentRouterRipAutoSummaryMode 1.3.6.1.4.1.4413.1.1.2.3.3
Sets the RIP auto summarization mode in the router. A value of enable(1) means that routes advertized by this RIP router are combined, or summarized, whenever possible into aggregates. When set to disable(2), routes are not aggregated in RIP updates generated by this router. The default auto summary mode is enable(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentRouterRipHostRoutesAcceptMode 1.3.6.1.4.1.4413.1.1.2.3.4
Sets the RIP host route acceptance mode in the router. A value of enable(1) means that host routes advertized to this RIP router will be accepted (learned) into its routing table. When set to disable(2), host routes advertized in RIP updates from neighboring routers are ignored. The default host routes accept mode is enable(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentRouterRipDefaultMetric 1.3.6.1.4.1.4413.1.1.2.3.5
Default metric of redistributed routes, when RIP redistributes from other protocols. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..15).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 1..15  

agentRouterRipDefaultMetricConfigured 1.3.6.1.4.1.4413.1.1.2.3.6
Flag to determine whether RIP default-metric is configured or not. Set to 'false' to unconfigure the default route metric. Set to 'true' is not allowed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentRouterRipDefaultInfoOriginate 1.3.6.1.4.1.4413.1.1.2.3.7
Flag to determine, whether RIP can advertise a default-route learned from another protocol.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentRipRouteRedistTable 1.3.6.1.4.1.4413.1.1.2.3.8
This table contains the MIB objects required to configure route-redistribution for RIP. Here, RIP is the Destination protocol and the source protocols can be any of : BGP, OSPF, Static, Connected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentRipRouteRedistEntry

agentRipRouteRedistEntry 1.3.6.1.4.1.4413.1.1.2.3.8.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentRipRouteRedistEntry  

agentRipRouteRedistSource 1.3.6.1.4.1.4413.1.1.2.3.8.1.1
Source route, from which RIP can redistribute routes. This object also acts as the identifier for the RIP redistribution Table entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER connected(1), static(2), ospf(3), bgp(4)  

agentRipRouteRedistMode 1.3.6.1.4.1.4413.1.1.2.3.8.1.2
User enabels/disables route-redistribution for a particular source protocol.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentRipRouteRedistMetric 1.3.6.1.4.1.4413.1.1.2.3.8.1.3
Metric used for redistributing a particular source protocol route into RIP. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..15).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 1..15  

agentRipRouteRedistMetricConfigured 1.3.6.1.4.1.4413.1.1.2.3.8.1.4
Flag to determine whether RIP redistribute-metric is configured or not. Set to 'false' to unconfigure redistribute metric. Set to 'true' is not allowed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentRipRouteRedistMatchInternal 1.3.6.1.4.1.4413.1.1.2.3.8.1.5
If this flag is true, RIP redistributes OSPF internal routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

agentRipRouteRedistMatchExternal1 1.3.6.1.4.1.4413.1.1.2.3.8.1.6
If this flag is true, RIP redistributes OSPF External1 routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

agentRipRouteRedistMatchExternal2 1.3.6.1.4.1.4413.1.1.2.3.8.1.7
If this flag is true, RIP redistributes OSPF External2 routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

agentRipRouteRedistMatchNSSAExternal1 1.3.6.1.4.1.4413.1.1.2.3.8.1.8
If this flag is true, RIP redistributes OSPF NSSA-External1 routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

agentRipRouteRedistMatchNSSAExternal2 1.3.6.1.4.1.4413.1.1.2.3.8.1.9
If this flag is true, RIP redistributes OSPF NSSA-External2 routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

agentRipRouteRedistDistList 1.3.6.1.4.1.4413.1.1.2.3.8.1.10
Access-list number of the access-list, which filters routes received from a source-protocol. A value of 0 indicates no distribute list is configured.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..199  

agentRipRouteRedistDistListConfigured 1.3.6.1.4.1.4413.1.1.2.3.8.1.11
Flag to determine whether Access-list is configured or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentRip2IfConfTable 1.3.6.1.4.1.4413.1.1.2.3.9
A list of subnets which require separate configuration in RIP. Augments rip2IfConfTable in the RIPv2-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentRip2IfConfEntry

agentRip2IfConfEntry 1.3.6.1.4.1.4413.1.1.2.3.9.1
A Single Routing Domain in a single Subnet. Augments rip2IfConfEntry in RIPv2-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentRip2IfConfEntry  

agentRip2IfConfAuthKeyId 1.3.6.1.4.1.4413.1.1.2.3.9.1.1
The identifier for the authentication key used on this interface. This field is only meaningful when the RIPv2-MIB rip2IfConfAuthType is md5(3); otherwise, the value is not used.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..255  

agentRouterRipRoutePref 1.3.6.1.4.1.4413.1.1.2.3.10
The route preference, sometimes called administrative distance, for RIP routes. A route with a preference of 255 is considered unreachable.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..255  

agentRouterOspfConfigGroup 1.3.6.1.4.1.4413.1.1.2.4
OBJECT IDENTIFIER    

agentOspfDefaultMetric 1.3.6.1.4.1.4413.1.1.2.4.1
Default metric of redistributed routes, when OSPF redistributes from other protocols. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..16777214).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 1..16777214  

agentOspfDefaultMetricConfigured 1.3.6.1.4.1.4413.1.1.2.4.2
Flag to determine whether OSPF default-metric is configured or not. Set to 'false' to unconfigure the OSPF default-metric. Set to 'true' is not allowed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentOspfDefaultInfoOriginate 1.3.6.1.4.1.4413.1.1.2.4.3
Flag to determine, whether OSPF can advertise a default-route learned from another protocol.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentOspfDefaultInfoOriginateAlways 1.3.6.1.4.1.4413.1.1.2.4.4
When this flag is true, the router advertises 0.0.0.0/0.0.0.0 always. Without this option, OSPF will only advertise 0.0.0.0/0.0.0.0 if the router's forwarding table contains a default route.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentOspfDefaultInfoOriginateMetric 1.3.6.1.4.1.4413.1.1.2.4.5
Metric of the default route, which OSPF advertises when learned from other protocol. (0) indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..16777214).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 1..16777214  

agentOspfDefaultInfoOriginateMetricConfigured 1.3.6.1.4.1.4413.1.1.2.4.6
Flag to determine whether OSPF default-info originate metric is configured or not. Setting to false unconfigures the default route metric. Setting to true is not allowed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentOspfDefaultInfoOriginateMetricType 1.3.6.1.4.1.4413.1.1.2.4.7
Metric Type of the default route,which OSPF advertises when learned from other protocol. It can be 1(external type 1) or 2(external type 2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER externalType1(1), externalType2(2)  

agentOspfRouteRedistTable 1.3.6.1.4.1.4413.1.1.2.4.8
This table contains the MIB objects required to configure route-redistribution for OSPF. Here, OSPF is the Destination protocol and the source protocols can be any of : BGP, RIP, Static, Connected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentOspfRouteRedistEntry

agentOspfRouteRedistEntry 1.3.6.1.4.1.4413.1.1.2.4.8.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentOspfRouteRedistEntry  

agentOspfRouteRedistSource 1.3.6.1.4.1.4413.1.1.2.4.8.1.1
Source protocol, from which OSPF can redistribute routes. This object also acts as the identifier for the OSPF redistribution Table entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER connected(1), static(2), rip(3), bgp(4)  

agentOspfRouteRedistMode 1.3.6.1.4.1.4413.1.1.2.4.8.1.2
User enabels/disables route-redistribution for a particular source protocol.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentOspfRouteRedistMetric 1.3.6.1.4.1.4413.1.1.2.4.8.1.3
Metric used for redistributing a particular source protocol route into OSPF.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..16777214  

agentOspfRouteRedistMetricConfigured 1.3.6.1.4.1.4413.1.1.2.4.8.1.4
Flag to determine whether OSPF redistribute-metric is configured or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentOspfRouteRedistMetricType 1.3.6.1.4.1.4413.1.1.2.4.8.1.5
Metric Type of routes,which OSPF redistributes from other source protocols. It can be 1(external type 1) or 2(external type 2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER externalType1(1), externalType2(2)  

agentOspfRouteRedistTag 1.3.6.1.4.1.4413.1.1.2.4.8.1.6
It specifies the tag field in routes redistributed by OSPF.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

agentOspfRouteRedistSubnets 1.3.6.1.4.1.4413.1.1.2.4.8.1.7
If this value is false, then OSPF will not redistribute subnetted routes.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentOspfRouteRedistDistList 1.3.6.1.4.1.4413.1.1.2.4.8.1.8
Access-list number of the access-list, which filters routes received from a source-protocol.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..199  

agentOspfRouteRedistDistListConfigured 1.3.6.1.4.1.4413.1.1.2.4.8.1.9
Flag to determine whether Access-list is configured or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentOspfIfTable 1.3.6.1.4.1.4413.1.1.2.4.9
The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF. Augments ospfIfTable from the OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentOspfIfEntry

agentOspfIfEntry 1.3.6.1.4.1.4413.1.1.2.4.9.1
The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF. Augments ospfIfEntry in OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentOspfIfEntry  

agentOspfIfAuthKeyId 1.3.6.1.4.1.4413.1.1.2.4.9.1.1
The identifier for the authentication key used on this interface. This field is only meaningful when the OSPF-MIB ospfIfAuthType is md5(2); otherwise, the value is not used.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..255  

agentOspfIfIpMtuIgnoreFlag 1.3.6.1.4.1.4413.1.1.2.4.9.1.2
Configures the IP MTU Ignore Flag value for this OSPF interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentOspfIfPassiveMode 1.3.6.1.4.1.4413.1.1.2.4.9.1.3
Flag to determine whether the interface is passive. A passive interface will not participate in the OSPF adjacency formation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentOspfIfAdvertiseSecondaries 1.3.6.1.4.1.4413.1.1.2.4.9.1.4
Configures the advertisability of the secondary addresses configured on this interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentOspfVirtIfTable 1.3.6.1.4.1.4413.1.1.2.4.10
Information about this router's virtual inter- faces. Augments ospfVirtIfTable from the OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentOspfVirtIfEntry

agentOspfVirtIfEntry 1.3.6.1.4.1.4413.1.1.2.4.10.1
Information about a single Virtual Interface. Augments ospfVirtIfEntry in OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentOspfVirtIfEntry  

agentOspfVirtIfAuthKeyId 1.3.6.1.4.1.4413.1.1.2.4.10.1.1
The identifier for the authentication key used on this virtual interface. This field is only meaningful when the OSPF-MIB ospfVirtIfAuthType is md5(2); otherwise, the value is not used.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..255  

agentRouterOspfRFC1583CompatibilityMode 1.3.6.1.4.1.4413.1.1.2.4.11
From RFC2328: Controls the preference rules used in Section 16.4 when choosing among multiple AS-external-LSAs advertising the same destination. When set to 'enabled', the preference rules remain those specified by RFC 1583 ([Ref9]). When set to 'disabled', the preference rules are those stated in Section 16.4.1, which prevent routing loops when AS- external-LSAs for the same destination have been originated from different areas. Set to 'enabled' by default. In order to minimize the chance of routing loops, all OSPF routers in an OSPF routing domain should have RFC1583Compatibility set identically. When there are routers present that have not been updated with the functionality specified in Section 16.4.1 of this memo, all routers should have RFC1583Compatibility set to 'enabled'. Otherwise, all routers should have RFC1583Compatibility set to 'disabled', preventing all routing loops.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentOspfSpfDelayTime 1.3.6.1.4.1.4413.1.1.2.4.12
Delay time (in seconds) between when OSPF receives a topology change and when it starts an SPF calculation. It can be an integer from 0 to 65535. The default time is 5 seconds. A value of 0 means that there is no delay; that is, the SPF calculation is started immediately.
Status: current Access: read-write
OBJECT-TYPE    
  SpfTimerRange  

agentOspfSpfHoldTime 1.3.6.1.4.1.4413.1.1.2.4.13
Minimum time (in seconds) between two consecutive SPF calculations. It can be an integer from 0 to 65535. The default time is 10 seconds. A value of 0 means that there is no delay; that is, two SPF calculations can be done, one immediately after the other.
Status: current Access: read-write
OBJECT-TYPE    
  SpfTimerRange  

agentOspfAutoCostRefBw 1.3.6.1.4.1.4413.1.1.2.4.14
Auto cost refernece bandwidth of the router interafaces for ospf metric calculations. It can be an integer from 1 to 4294967. The default reference bandwidth is 100 Mbps.
Status: current Access: read-write
OBJECT-TYPE    
  AutoCostRefBw  

agentOspfOpaqueLsaSupport 1.3.6.1.4.1.4413.1.1.2.4.15
The router's support for Opaque LSA types. This object is persistent and when written the entity SHOULD save the change to non-volatile storage.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentOspfAreaOpaqueLsdbTable 1.3.6.1.4.1.4413.1.1.2.4.16
The OSPF Process's Area Link State Database (LSDB). The LSDB contains type-10 Link State Advertisements from throughout the areas that the device is attached to.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentOspfAreaOpaqueLsdbEntry

agentOspfAreaOpaqueLsdbEntry 1.3.6.1.4.1.4413.1.1.2.4.16.1
A single AreaOpaque Link State Advertisement.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentOspfAreaOpaqueLsdbEntry  

agentOspfAreaOpaqueLsdbAreaId 1.3.6.1.4.1.4413.1.1.2.4.16.1.1
The 32 bit identifier of the Area from which the LSA was received.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

agentOspfAreaOpaqueLsdbType 1.3.6.1.4.1.4413.1.1.2.4.16.1.2
The type of the link state advertisement. Each link state type has a separate advertisement format.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER areaOpaqueLink(10)  

agentOspfAreaOpaqueLsdbLsid 1.3.6.1.4.1.4413.1.1.2.4.16.1.3
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

agentOspfAreaOpaqueLsdbRouterId 1.3.6.1.4.1.4413.1.1.2.4.16.1.4
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

agentOspfAreaOpaqueLsdbSequence 1.3.6.1.4.1.4413.1.1.2.4.16.1.5
The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentOspfAreaOpaqueLsdbAge 1.3.6.1.4.1.4413.1.1.2.4.16.1.6
This field is the age of the link state advertisement in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentOspfAreaOpaqueLsdbChecksum 1.3.6.1.4.1.4413.1.1.2.4.16.1.7
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentOspfAreaOpaqueLsdbAdvertisement 1.3.6.1.4.1.4413.1.1.2.4.16.1.8
The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..65535)  

agentOspfLocalLsdbTable 1.3.6.1.4.1.4413.1.1.2.4.17
The OSPF Process's Link-Local Link State Database for non-virtual links. This table is identical to the OSPF LSDB Table in format, but contains only Link-Local Link State Advertisements for non-virtual links. The purpose is to allow Link-Local LSAs to be displayed for each non-virtual interface. This table is implemented to support type-9 LSAs which are defined in 'The OSPF Opaque LSA Option'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentOspfLocalLsdbEntry

agentOspfLocalLsdbEntry 1.3.6.1.4.1.4413.1.1.2.4.17.1
A single Link State Advertisement.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentOspfLocalLsdbEntry  

agentOspfLocalLsdbIpAddress 1.3.6.1.4.1.4413.1.1.2.4.17.1.1
The IP Address of the interface from which the LSA was received if the interface is numbered.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

agentOspfLocalLsdbAddressLessIf 1.3.6.1.4.1.4413.1.1.2.4.17.1.2
The Interface Index of the interface from which the LSA was received if the interface is unnumbered.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

agentOspfLocalLsdbType 1.3.6.1.4.1.4413.1.1.2.4.17.1.3
The type of the link state advertisement. Each link state type has a separate advertise- ment format.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER localOpaqueLink(9)  

agentOspfLocalLsdbLsid 1.3.6.1.4.1.4413.1.1.2.4.17.1.4
The Link State ID is an LS Type Specific field containing a 32 bit identifier in IP address format; it identifies the piece of the routing domain that is being described by the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

agentOspfLocalLsdbRouterId 1.3.6.1.4.1.4413.1.1.2.4.17.1.5
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
Status: current Access: read-only
OBJECT-TYPE    
  RouterID  

agentOspfLocalLsdbSequence 1.3.6.1.4.1.4413.1.1.2.4.17.1.6
The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentOspfLocalLsdbAge 1.3.6.1.4.1.4413.1.1.2.4.17.1.7
This field is the age of the link state adver- tisement in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentOspfLocalLsdbChecksum 1.3.6.1.4.1.4413.1.1.2.4.17.1.8
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentOspfLocalLsdbAdvertisement 1.3.6.1.4.1.4413.1.1.2.4.17.1.9
The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..65535)  

agentOspfAsLsdbTable 1.3.6.1.4.1.4413.1.1.2.4.18
The OSPF Process's AS-scope LSA Link State Database. The Database contains the AS-scope Link State Advertisements from throughout the areas that the device is attached to. This table is identical to the OSPF LSDB Table in format, but contains only AS-scope Link State Advertisements. The purpose is to allow AS-scope LSAs to be displayed once for the router rather than once in each non-stub area.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentOspfAsLsdbEntry

agentOspfAsLsdbEntry 1.3.6.1.4.1.4413.1.1.2.4.18.1
A single Link State Advertisement.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentOspfAsLsdbEntry  

agentOspfAsLsdbType 1.3.6.1.4.1.4413.1.1.2.4.18.1.1
The type of the link state advertisement. Each link state type has a separate advertise- ment format.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER asOpaqueLink(11)  

agentOspfAsLsdbLsid 1.3.6.1.4.1.4413.1.1.2.4.18.1.2
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

agentOspfAsLsdbRouterId 1.3.6.1.4.1.4413.1.1.2.4.18.1.3
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
Status: current Access: read-only
OBJECT-TYPE    
  RouterID  

agentOspfAsLsdbSequence 1.3.6.1.4.1.4413.1.1.2.4.18.1.4
The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentOspfAsLsdbAge 1.3.6.1.4.1.4413.1.1.2.4.18.1.5
This field is the age of the link state adver- tisement in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentOspfAsLsdbChecksum 1.3.6.1.4.1.4413.1.1.2.4.18.1.6
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentOspfAsLsdbAdvertisement 1.3.6.1.4.1.4413.1.1.2.4.18.1.7
The entire Link State Advertisement, including its header.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..65535)  

agentOspfDefaultPassiveMode 1.3.6.1.4.1.4413.1.1.2.4.19
Flag to determine, whether all the interfaces are passive interfaces by default. A passive interface will not participate in the OSPF adjacency formation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentOspfRoutePrefIntraArea 1.3.6.1.4.1.4413.1.1.2.4.20
The route preference, sometimes called administrative distance, for intra-area OSPFv2 routes. A route with a preference of 255 is considered unreachable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

agentOspfRoutePrefInterArea 1.3.6.1.4.1.4413.1.1.2.4.21
The route preference, sometimes called administrative distance, for inter-area OSPFv2 routes. A route with a preference of 255 is considered unreachable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

agentOspfRoutePrefExternal 1.3.6.1.4.1.4413.1.1.2.4.22
The route preference, sometimes called administrative distance, for external OSPFv2 routes. A route with a preference of 255 is considered unreachable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

agentSnmpTrapFlagsConfigGroupLayer3 1.3.6.1.4.1.4413.1.1.2.5
OBJECT IDENTIFIER    

agentSnmpVRRPNewMasterTrapFlag 1.3.6.1.4.1.4413.1.1.2.5.1
This flag enables the sending of VRRP new master notification traps.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentSnmpVRRPAuthFailureTrapFlag 1.3.6.1.4.1.4413.1.1.2.5.2
This flag enables the sending of VRRP authentication failure notification traps.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentBootpDhcpRelayGroup 1.3.6.1.4.1.4413.1.1.2.6
OBJECT IDENTIFIER    

agentBootpDhcpRelayMaxHopCount 1.3.6.1.4.1.4413.1.1.2.6.1
The BOOTP/DHCP Max Hop Count. The relay agent silently discards BOOTREQUEST messages whose hops field exceeds the value 16 assuming that the request is looped through the intermediate agents. The default value is 4.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..16  

agentBootpDhcpRelayForwardingIp 1.3.6.1.4.1.4413.1.1.2.6.2
DHCP server addresses are now configured through IP helper.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

agentBootpDhcpRelayForwardMode 1.3.6.1.4.1.4413.1.1.2.6.3
The DHCP relay admin mode is replaced by the IP helper admin mode.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentBootpDhcpRelayMinWaitTime 1.3.6.1.4.1.4413.1.1.2.6.4
The BOOTP/DHCP Minimum Wait Time. When the BOOTP relay agent receives a BOOTREQUEST message, it MAY use the value of the 'secs' (seconds since client began booting) field of the request as a factor in deciding whether to relay the request or not.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

agentBootpDhcpRelayCircuitIdOptionMode 1.3.6.1.4.1.4413.1.1.2.6.5
The BOOTP/DHCP Circuit ID Option Mode. This flag is set to enable/disable the network element to add/remove the DHCP Relay agent Circuit ID sub-options.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentBootpDhcpRelayNumOfRequestsReceived 1.3.6.1.4.1.4413.1.1.2.6.6
Replaced by IP helper statistics.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32  

agentBootpDhcpRelayNumOfRequestsForwarded 1.3.6.1.4.1.4413.1.1.2.6.7
Replaced by IP helper statistics.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32  

agentBootpDhcpRelayNumOfDiscards 1.3.6.1.4.1.4413.1.1.2.6.8
Replaced by IP helper statistics.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32  

agentECMPGroup 1.3.6.1.4.1.4413.1.1.2.7
OBJECT IDENTIFIER    

agentECMPOspfMaxPaths 1.3.6.1.4.1.4413.1.1.2.7.1
It sets the number of paths that OSPF can report for a given destination where maxpaths is platform-dependent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

agentRouterVrrpConfigGroup 1.3.6.1.4.1.4413.1.1.2.8
OBJECT IDENTIFIER    

agentRouterVrrpAdminState 1.3.6.1.4.1.4413.1.1.2.8.1
Sets the administrative mode of VRRP in the router.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentRouterVrrpConfiguredTable 1.3.6.1.4.1.4413.1.1.2.8.2
Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of `agentRouterVrrpConfiguredEntry' items.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentRouterVrrpConfiguredEntry

agentRouterVrrpConfiguredEntry 1.3.6.1.4.1.4413.1.1.2.8.2.1
An entry in the table contains operational priority that is associated with a virtual router.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentRouterVrrpConfiguredEntry  

agentRouterVrrpConfiguredPriority 1.3.6.1.4.1.4413.1.1.2.8.2.1.1
This object specifies the value set by the vrrpOperPriority object. The GET operation on 'vrrpOperPriority' will be affected by both the tracking process and the configured priority set by the vrrpOperPriority object.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..254  

agentVrrpOperations 1.3.6.1.4.1.4413.1.1.2.9
OBJECT IDENTIFIER    

agentRouterVrrpOperTable 1.3.6.1.4.1.4413.1.1.2.9.1
Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of `agentRouterVrrpOperEntry' items.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentRouterVrrpOperEntry

agentRouterVrrpOperEntry 1.3.6.1.4.1.4413.1.1.2.9.1.1
An entry in the table contains operational priority that is associated with a virtual router.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  AgentRouterVrrpOperEntry  

agentRouterVrrpOperPriority 1.3.6.1.4.1.4413.1.1.2.9.1.1.1
This object specifies the operational priority of the VRRP router. This value will be afftected by both the tracking process and the configured priority set by the vrrpOperPriority object.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

agentRouterVrrpTrackGroup 1.3.6.1.4.1.4413.1.1.2.10
OBJECT IDENTIFIER    

agentRouterVrrpTrackIntfTable 1.3.6.1.4.1.4413.1.1.2.10.1
Tracking table for a VRRP router which consists of agentRouterVrrpTrackIntfEntry items.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentRouterVrrpTrackIntfEntry

agentRouterVrrpTrackIntfEntry 1.3.6.1.4.1.4413.1.1.2.10.1.1
An entry in the table contains tracked IP interfaces associated with a virtual router.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentRouterVrrpTrackIntfEntry  

agentRouterVrrpTrackIntf 1.3.6.1.4.1.4413.1.1.2.10.1.1.1
This object specifies the interface to be tracked.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

agentRouterVrrpTrackIfPrioDec 1.3.6.1.4.1.4413.1.1.2.10.1.1.2
This object specifies the decrement priority of the VRRP router.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..254  

agentRouterVrrpTrackIfState 1.3.6.1.4.1.4413.1.1.2.10.1.1.3
This object specifies the IP state of the tracked interface for the virtual router.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

agentRouterVrrpTrackIfStatus 1.3.6.1.4.1.4413.1.1.2.10.1.1.4
The row status variable, used in accordance to installation and removal conventions for conceptual rows. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). The newly created row will be in active state later. To destroy the row set this object to destroy.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

agentRouterVrrpTrackRouteTable 1.3.6.1.4.1.4413.1.1.2.10.2
Tracking table for a VRRP router which consists of a 'agentRouterVrrpTrackRouteEntry' items.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentRouterVrrpTrackRouteEntry

agentRouterVrrpTrackRouteEntry 1.3.6.1.4.1.4413.1.1.2.10.2.1
An entry in the table contains tracked Routes associated with a virtual router.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentRouterVrrpTrackRouteEntry  

agentRouterVrrpTrackRtPfx 1.3.6.1.4.1.4413.1.1.2.10.2.1.1
This object specifies the prefix of the route to be tracked.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

agentRouterVrrpTrackRtPfxLen 1.3.6.1.4.1.4413.1.1.2.10.2.1.2
This object specifies prefix length of the route to be tracked.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..32  

agentRouterVrrpTrackRtPrioDec 1.3.6.1.4.1.4413.1.1.2.10.2.1.3
This object specifies the decrement priority of the VRRP router.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..254  

agentRouterVrrpTrackRtReachable 1.3.6.1.4.1.4413.1.1.2.10.2.1.4
This object specifies the reachability of the tracked route.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

agentRouterVrrpTrackRtStatus 1.3.6.1.4.1.4413.1.1.2.10.2.1.5
The row status variable, used in accordance to installation and removal conventions for conceptual rows. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). The newly created row will be in active state later. To delete the tracked route set this object to destroy.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

agentIpHelperGroup 1.3.6.1.4.1.4413.1.1.2.11
OBJECT IDENTIFIER    

agentIpHelperAdminMode 1.3.6.1.4.1.4413.1.1.2.11.1
Administratively enable or disable IP helper.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

agentDhcpClientMsgsReceived 1.3.6.1.4.1.4413.1.1.2.11.2
The Number of DHCP Requests Received. Total number of DHCP requests received from all clients.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentDhcpClientMsgsRelayed 1.3.6.1.4.1.4413.1.1.2.11.3
The Number of DHCP Requests Forwarded. Total number of DHCP requests relayed to a server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentDhcpServerMsgsReceived 1.3.6.1.4.1.4413.1.1.2.11.4
The number of DHCP messages received from a server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentDhcpServerMsgsRelayed 1.3.6.1.4.1.4413.1.1.2.11.5
The number of DHCP messages relayed to a server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentUdpClientMsgsReceived 1.3.6.1.4.1.4413.1.1.2.11.6
The number of UDP messages received from all clients.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentUdpClientMsgsRelayed 1.3.6.1.4.1.4413.1.1.2.11.7
The number of UDP messages relayed to a server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentSwitchIpHelperAddressTable 1.3.6.1.4.1.4413.1.1.2.11.8
Contains a list of IP helper addresses configured globally.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchIpHelperAddressEntry

agentSwitchIpHelperAddressEntry 1.3.6.1.4.1.4413.1.1.2.11.8.1
An IP Helper address that applies to packets received on any interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentSwitchIpHelperAddressEntry  

agentSwitchIpHelperAddress 1.3.6.1.4.1.4413.1.1.2.11.8.1.1
The IP Helper address assigned to this interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

agentSwitchIpHelperUdpPort 1.3.6.1.4.1.4413.1.1.2.11.8.1.2
UDP port number.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

agentSwitchIpHelperHitCount 1.3.6.1.4.1.4413.1.1.2.11.8.1.3
The number of times a packet has been forwarded or discarded according to this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentSwitchIpHelperStatus 1.3.6.1.4.1.4413.1.1.2.11.8.1.4
Creates a new entry in the global IP Helper address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

agentUdpClientMsgsTtlExpired 1.3.6.1.4.1.4413.1.1.2.11.9
The number of UDP messages received with an expired TTL.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentUdpClientMsgsDiscarded 1.3.6.1.4.1.4413.1.1.2.11.10
The number of UDP messages that matched a discard entry.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentInternalVlanGroup 1.3.6.1.4.1.4413.1.1.2.12
OBJECT IDENTIFIER    

agentInternalVlanBase 1.3.6.1.4.1.4413.1.1.2.12.1
The VLAN ID internally assigned to the first port-based routing interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

agentInternalVlanPolicy 1.3.6.1.4.1.4413.1.1.2.12.2
Whether to search up or down from the base VLAN ID for a free VLAN ID to assign to a port-based routing interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ascending(0), descending(1)  

agentSwitchInternalVlanTable 1.3.6.1.4.1.4413.1.1.2.12.3
Contains a list of VLAN IDs used internally for port-based routing interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentSwitchInternalVlanEntry

agentSwitchInternalVlanEntry 1.3.6.1.4.1.4413.1.1.2.12.3.1
A VLAN ID internally assigned to a port-based routing interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentSwitchInternalVlanEntry  

agentSwitchInternalVlanId 1.3.6.1.4.1.4413.1.1.2.12.3.1.1
A VLAN ID internally assigned to a port-based routing interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

agentSwitchInternalVlanIfIndex 1.3.6.1.4.1.4413.1.1.2.12.3.1.2
Interface index of port-based routing interface using this VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentOspfQueueGroup 1.3.6.1.4.1.4413.1.1.2.13
OBJECT IDENTIFIER    

agentOspfQueueTable 1.3.6.1.4.1.4413.1.1.2.13.1
Table lists information about OSPFv2 message queue utilization.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentOspfQueueEntry

agentOspfQueueEntry 1.3.6.1.4.1.4413.1.1.2.13.1.1
Information on a specific OSPFv2 message queue.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentOspfQueueEntry  

agentOspfQueueIndex 1.3.6.1.4.1.4413.1.1.2.13.1.1.1
Index value for this message queue.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

agentOspfQueueName 1.3.6.1.4.1.4413.1.1.2.13.1.1.2
Name of an OSPFv2 message queue.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

agentOspfQueueLength 1.3.6.1.4.1.4413.1.1.2.13.1.1.3
The number of messages currently in the message queue.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfQueueHigh 1.3.6.1.4.1.4413.1.1.2.13.1.1.4
The high water mark of the number of messages in the message queue.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfQueueDrops 1.3.6.1.4.1.4413.1.1.2.13.1.1.5
The number of items dropped because the message queue was full.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfQueueLimit 1.3.6.1.4.1.4413.1.1.2.13.1.1.6
The maximum number of messages this queue can hold.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentOspfPacketStatsGroup 1.3.6.1.4.1.4413.1.1.2.14
OBJECT IDENTIFIER    

agentOspfCountersCleared 1.3.6.1.4.1.4413.1.1.2.14.1
The time since OSPFv2 counters were last cleared, in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentOspfLsaRetxCount 1.3.6.1.4.1.4413.1.1.2.14.2
The total number of LSAs retransmitted since OSPF counters were last cleared. If the same LSA is retransmitted to multiple neighbors, the count is incremented for each neighbor.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfHellosRx 1.3.6.1.4.1.4413.1.1.2.14.3
The total number of OSPFv2 Hello packets received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfHellosTx 1.3.6.1.4.1.4413.1.1.2.14.4
The total number of OSPFv2 Hello packets transmitted since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfDdRx 1.3.6.1.4.1.4413.1.1.2.14.5
The total number of OSPFv2 Database Description packets received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfDdTx 1.3.6.1.4.1.4413.1.1.2.14.6
The total number of OSPFv2 Database Description packets transmitted since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfLsReqRx 1.3.6.1.4.1.4413.1.1.2.14.7
The total number of OSPFv2 LS Request packets received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfLsReqTx 1.3.6.1.4.1.4413.1.1.2.14.8
The total number of OSPFv2 LS Request packets transmitted since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfLsUpdatesRx 1.3.6.1.4.1.4413.1.1.2.14.9
The total number of OSPFv2 LS Update packets received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfLsUpdatesTx 1.3.6.1.4.1.4413.1.1.2.14.10
The total number of OSPFv2 LS Update packets transmitted since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfLsAckRx 1.3.6.1.4.1.4413.1.1.2.14.11
The total number of OSPFv2 LS Acknowledgement packets received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfLsAckTx 1.3.6.1.4.1.4413.1.1.2.14.12
The total number of OSPFv2 LS Acknowledgement packets transmitted since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfLsUpdatesRxMax 1.3.6.1.4.1.4413.1.1.2.14.13
The maximum rate of OSPFv2 LS Update packets received over any 5-second interval since OSPF counters were last cleared. The rate is given in packets per second (that is, the number of packets received during the 5-second interval, divided by 5).
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfLsUpdatesTxMax 1.3.6.1.4.1.4413.1.1.2.14.14
The maximum rate of OSPFv2 LS Update packets transmitted over any 5-second interval since OSPF counters were last cleared. The rate is given in packets per second (that is, the number of packets transmitted during the 5-second interval, divided by 5).
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfType1LsasRx 1.3.6.1.4.1.4413.1.1.2.14.15
The number of type 1 (router) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfType2LsasRx 1.3.6.1.4.1.4413.1.1.2.14.16
The number of type 2 (network) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfType3LsasRx 1.3.6.1.4.1.4413.1.1.2.14.17
The number of type 3 (network summary) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfType4LsasRx 1.3.6.1.4.1.4413.1.1.2.14.18
The number of type 4 (ASBR summary) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfType5LsasRx 1.3.6.1.4.1.4413.1.1.2.14.19
The number of type 5 (external) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfType7LsasRx 1.3.6.1.4.1.4413.1.1.2.14.20
The number of type 7 (NSSA external) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfType9LsasRx 1.3.6.1.4.1.4413.1.1.2.14.21
The number of type 9 (Link Opaque) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfType10LsasRx 1.3.6.1.4.1.4413.1.1.2.14.22
The number of type 10 (Area Opaque) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfType11LsasRx 1.3.6.1.4.1.4413.1.1.2.14.23
The number of type 11 (AS Opaque) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentOspfSpfStatsTable 1.3.6.1.4.1.4413.1.1.2.15
Contains statistics for the twenty most recent SPF runs. Statistics are reported from the oldest SPF first to the most recent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentOspfSpfStatsEntry

agentOspfSpfStatsEntry 1.3.6.1.4.1.4413.1.1.2.15.1
Statistics for a single SPF run.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentOspfSpfStatsEntry  

agentOspfSpfIndex 1.3.6.1.4.1.4413.1.1.2.15.1.1
Integer that uniquely identifies an SPF run. This value is incremented each time OSPF runs a full routing table calculation.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

agentOspfSpfStatsDeltaT 1.3.6.1.4.1.4413.1.1.2.15.1.2
How long since this routing table calculation ran. The time is given in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentOspfSpfStatsIntra 1.3.6.1.4.1.4413.1.1.2.15.1.3
Number of milliseconds to compute intra-area routes.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfSpfStatsSumm 1.3.6.1.4.1.4413.1.1.2.15.1.4
Number of milliseconds to compute inter-area routes.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfSpfStatsExt 1.3.6.1.4.1.4413.1.1.2.15.1.5
Number of milliseconds to compute external routes.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfSpfStatsSpfTotal 1.3.6.1.4.1.4413.1.1.2.15.1.6
Number of milliseconds for entire routing table calculation.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfSpfStatsRibUpdate 1.3.6.1.4.1.4413.1.1.2.15.1.7
Number of milliseconds to update the common routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfSpfStatsReason 1.3.6.1.4.1.4413.1.1.2.15.1.8
Reasons why a routing table calculation was required. R - new router LSA, N - new Network LSA, SN - new network summary LSA, SA - new ASBR summary LSA, X - new external LSA.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

agentRoutingHeapGroup 1.3.6.1.4.1.4413.1.1.2.16
OBJECT IDENTIFIER    

agentRoutingHeapSize 1.3.6.1.4.1.4413.1.1.2.16.1
The size of the routing heap, in bytes. Unicast routing protocols and ARP allocate memory from the routing heap.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentRoutingHeapInUse 1.3.6.1.4.1.4413.1.1.2.16.2
The number of bytes currently allocated from the routing heap.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentRoutingHeapHigh 1.3.6.1.4.1.4413.1.1.2.16.3
High water mark for the number of bytes allocated from the routing heap.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentRoutingTableSummaryGroup 1.3.6.1.4.1.4413.1.1.2.17
OBJECT IDENTIFIER    

agentConnectedRoutes 1.3.6.1.4.1.4413.1.1.2.17.1
The number of connected routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentStaticRoutes 1.3.6.1.4.1.4413.1.1.2.17.2
The number of static routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentRipRoutes 1.3.6.1.4.1.4413.1.1.2.17.3
The number of RIP routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfRoutes 1.3.6.1.4.1.4413.1.1.2.17.4
The number of OSPFv2 routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfIntraRoutes 1.3.6.1.4.1.4413.1.1.2.17.5
The number of OSPFv2 intra-area routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfInterRoutes 1.3.6.1.4.1.4413.1.1.2.17.6
The number of OSPFv2 inter-area routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfExt1Routes 1.3.6.1.4.1.4413.1.1.2.17.7
The number of OSPFv2 external type 1 routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfExt2Routes 1.3.6.1.4.1.4413.1.1.2.17.8
The number of OSPFv2 external type 2 routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentBgpRoutes 1.3.6.1.4.1.4413.1.1.2.17.9
The number of BGP routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentEbgpRoutes 1.3.6.1.4.1.4413.1.1.2.17.10
The number of external BGP routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentIbgpRoutes 1.3.6.1.4.1.4413.1.1.2.17.11
The number of internal BGP routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentLocalBgpRoutes 1.3.6.1.4.1.4413.1.1.2.17.12
The number of local BGP routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentRejectRoutes 1.3.6.1.4.1.4413.1.1.2.17.13
The number of reject routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentTotalRoutes 1.3.6.1.4.1.4413.1.1.2.17.14
The number of routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentBestRoutes 1.3.6.1.4.1.4413.1.1.2.17.15
The number of IPv4 routes in the forwarding table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentBestRoutesHigh 1.3.6.1.4.1.4413.1.1.2.17.16
The highest number of IPv4 routes in the forwarding table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentAlternateRoutes 1.3.6.1.4.1.4413.1.1.2.17.17
The number of alternate routes in the IPv4 routing table. An alternate route is less preferred than the best route and is not used for forwarding.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentRouteAdds 1.3.6.1.4.1.4413.1.1.2.17.18
The number of routes added to the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentRouteModifies 1.3.6.1.4.1.4413.1.1.2.17.19
The number of routes changed in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentRouteDeletes 1.3.6.1.4.1.4413.1.1.2.17.20
The number of routes removed from the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentUnresolvedRouteAdds 1.3.6.1.4.1.4413.1.1.2.17.21
The number of IPv4 route adds that failed because none of the route's next hops were on a local subnet.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentInvalidRouteAdds 1.3.6.1.4.1.4413.1.1.2.17.22
The number of IPv4 routes adds that failed because the route was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentFailedRouteAdds 1.3.6.1.4.1.4413.1.1.2.17.23
The number of IPv4 routes adds that failed because of a resource limitation in the routing table
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentReservedLocals 1.3.6.1.4.1.4413.1.1.2.17.24
The number of IPv4 routing table entries reserved for a local subnet on a routing interface that is down.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentUniqueNextHops 1.3.6.1.4.1.4413.1.1.2.17.25
The number of distinct next hops used among all IPv4 routes currently in the routing table. These include local interfaces for local routes and neighbors for indirect routes.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentUniqueNextHopsHigh 1.3.6.1.4.1.4413.1.1.2.17.26
The highest count of unique next hops since counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentNextHopGroups 1.3.6.1.4.1.4413.1.1.2.17.27
The current number of next hop groups in use by one or more routes. Each next hop group includes one or more next hops.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentNextHopGroupsHigh 1.3.6.1.4.1.4413.1.1.2.17.28
The highest count of next hop groups since counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentEcmpGroups 1.3.6.1.4.1.4413.1.1.2.17.29
The number of next hop groups with multiple next hops.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentEcmpGroupsHigh 1.3.6.1.4.1.4413.1.1.2.17.30
The high water mark of the number of ECMP groups.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentEcmpRoutes 1.3.6.1.4.1.4413.1.1.2.17.31
The current number of IPv4 routes with multiple next hops.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentTruncEcmpRoutes 1.3.6.1.4.1.4413.1.1.2.17.32
The number of ECMP routes that are currently installed in the forwarding table with just one next hop. The forwarding table may limit the number of ECMP routes or the number of ECMP groups. When an ECMP route cannot be installed because such a limit is reached, the route is installed with a single next hop.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentEcmpRetries 1.3.6.1.4.1.4413.1.1.2.17.33
The number of ECMP routes that have been installed in the forwarding table after initially being installed with a single next hop.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

agentEcmpCountTable 1.3.6.1.4.1.4413.1.1.2.18
A count of the number of routes with each number of ECMP next hops.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentEcmpCountEntry

agentEcmpCountEntry 1.3.6.1.4.1.4413.1.1.2.18.1
Number of IPv4 routes with a given number of next hops.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentEcmpCountEntry  

agentEcmpNextHopCount 1.3.6.1.4.1.4413.1.1.2.18.1.1
The number of next hops in a route. From 0 to the maximum number of next hops in an ECMP route. The maximum varies by platform.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..128  

agentEcmpRouteCount 1.3.6.1.4.1.4413.1.1.2.18.1.2
The number of IPv4 routes with agentEcmpNextHopCount next hops.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

agentOspfStubRouterGroup 1.3.6.1.4.1.4413.1.1.2.19
OBJECT IDENTIFIER    

ospfStubRouterAdvertisement 1.3.6.1.4.1.4413.1.1.2.19.1
Specifies how the router LSAs are advertised by the router. The value doNotAdvertise indicates the advertisement of a standard router LSA and is the default value. The value advertise indicates the advertisement of a stub router LSA.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER doNotAdvertise(1), advertise(2)  

agentOspfStubRouterReason 1.3.6.1.4.1.4413.1.1.2.19.2
This indicates the reason because of which the router is in Stub mode. This is valid only if the agentOspfStubRouterMode is 'active'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER configured(0), startup(1), resource-limitation(2)  

agentOspfStubRouterStartupTimeRemaining 1.3.6.1.4.1.4413.1.1.2.19.3
The time remaining (in seconds) for the router to come out of the stub mode. This is valid only if the agentOspfStubRouterReason is 'startup'.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentOspfStubRouterDuration 1.3.6.1.4.1.4413.1.1.2.19.4
Time elapsed (in seconds) since the router last entered the stub router mode. This is valid only if the agentOspfStubRouterMode is 'active' and agentOspfStubRouterReason is 'resource-limitation'.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor