ES3528MO-MIB

File: ES3528MO-MIB.mib (521693 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC Q-BRIDGE-MIB
INET-ADDRESS-MIB IF-MIB P-BRIDGE-MIB
BRIDGE-MIB IEEE8021-PAE-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
Integer32 Counter32 IpAddress
Counter64 NOTIFICATION-TYPE enterprises
TimeTicks DisplayString RowStatus
TruthValue PortList VlanIndex
InetAddressType InetAddress InterfaceIndex
ifIndex EnabledStatus BridgeId
Timeout dot1dStpPort dot1dStpPortEntry
MacAddress dot1xAuthConfigEntry

Defined Types

KeySegment  
The total length of the key is 1024 characters, it is divided into 8 parts and stored in 8 separated mib variables as below: Key1: part 1 of the key (1-128) Key2: part 2 of the key (129-256) Key3: part 3 of the key (257-384) Key4: part 4 of the key (385-512) Key5: part 5 of the key (513-640) Key6: part 6 of the key (641-768) Key7: part 7 of the key (769-896) Key8: part 8 of the key (897-1024) Please note that if the key string is less then 1024 characters, the remaining part of the string will be filled by a zero-length string. For example, if the length of the key is 129, we will get a string of length 128 in Key1, and a string of length 1 in Key2, moreover, Key3 to Key8 will all be zero-length strings.
TEXTUAL-CONVENTION    
  DisplayString Size(0..128)  

ValidStatus  
A simple status value for the object to create and destroy a table entry. This is a simplified variant of RowStatus as it supports only two values. Setting it to valid(1) creates an entry. Setting it to invalid(2) destroys an entry.
TEXTUAL-CONVENTION    
  INTEGER valid(1), invalid(2)  

StaPathCostMode  
The path cost mode of a spanning tree algorithm, short(1) indicates that we retrieve/configure the spanning tree path cost as a 16 bit value and long(2) indicates that we retrieve/configure the spanning tree path cost as a 32 bit value.
TEXTUAL-CONVENTION    
  INTEGER short(1), long(2)  

FileCopyStatus  
The file copy result status.
TEXTUAL-CONVENTION    
  INTEGER fileCopyTftpUndefError(1), fileCopyTftpFileNotFound(2), fileCopyTftpAccessViolation(3), fileCopyTftpDiskFull(4), fileCopyTftpIllegalOperation(5), fileCopyTftpUnkownTransferId(6), fileCopyTftpFileExisted(7), fileCopyTftpNoSuchUser(8), fileCopyTftpTimeout(9), fileCopyTftpSendError(10), fileCopyTftpReceiverError(11), fileCopyTftpSocketOpenError(12), fileCopyTftpSocketBindError(13), fileCopyTftpUserCancel(14), fileCopyTftpCompleted(15), fileCopyParaError(16), fileCopyBusy(17), fileCopyUnknown(18), fileCopyReadFileError(19), fileCopySetStartupError(20), fileCopyFileSizeExceed(21), fileCopyMagicWordError(22), fileCopyImageTypeError(23), fileCopyHeaderChecksumError(24), fileCopyImageChecksumError(25), fileCopyWriteFlashFinish(26), fileCopyWriteFlashError(27), fileCopyWriteFlashProgramming(28), fileCopyError(29), fileCopySuccess(30), fileCopyCompleted(31)  

SwitchInfoEntry  
SEQUENCE    
  swUnitIndex Integer32
  swHardwareVer DisplayString
  swMicrocodeVer DisplayString
  swLoaderVer DisplayString
  swBootRomVer DisplayString
  swOpCodeVer DisplayString
  swPortNumber Integer32
  swPowerStatus INTEGER
  swRoleInSystem INTEGER
  swSerialNumber DisplayString
  swServiceTag DisplayString
  swModelNumber DisplayString
  swEpldVer DisplayString

SwitchIndivPowerEntry  
SEQUENCE    
  swIndivPowerUnitIndex Integer32
  swIndivPowerIndex INTEGER
  swIndivPowerStatus INTEGER

PortEntry  
SEQUENCE    
  portIndex Integer32
  portName DisplayString
  portType INTEGER
  portSpeedDpxCfg INTEGER
  portFlowCtrlCfg INTEGER
  portCapabilities BITS
  portAutonegotiation EnabledStatus
  portSpeedDpxStatus INTEGER
  portFlowCtrlStatus INTEGER
  portTrunkIndex Integer32
  portComboForcedMode INTEGER
  portMasterSlaveModeCfg INTEGER

CableDiagResultEntry  
SEQUENCE    
  cableDiagResultIfIndex Integer32
  cableDiagResultStatusPairA INTEGER
  cableDiagResultStatusPairB INTEGER
  cableDiagResultDistancePairA Integer32
  cableDiagResultDistancePairB Integer32
  cableDiagResultTime DisplayString

PortUtilEntry  
SEQUENCE    
  portUtilIfIndex Integer32
  portInOctetRate Counter64
  portInPacketRate Counter64
  portInUtil Integer32
  portOutOctetRate Counter64
  portOutPacketRate Counter64
  portOutUtil Integer32

TrunkEntry  
SEQUENCE    
  trunkIndex Integer32
  trunkPorts PortList
  trunkCreation INTEGER
  trunkStatus ValidStatus

LacpPortEntry  
SEQUENCE    
  lacpPortIndex Integer32
  lacpPortStatus EnabledStatus

StaPortEntry  
SEQUENCE    
  staPortFastForward EnabledStatus
  staPortProtocolMigration TruthValue
  staPortOperEdgePort TruthValue
  staPortAdminPointToPoint INTEGER
  staPortOperPointToPoint TruthValue
  staPortSystemStatus EnabledStatus
  staPortLongAdminPathCost Integer32
  staPortLongOperPathCost Integer32
  staPortRootGuardAdminStatus EnabledStatus
  staPortRootGuardOperStatus EnabledStatus
  staPortBpduGuard EnabledStatus
  staPortAdminEdgePortWithAuto INTEGER
  staPortBpduFilter EnabledStatus
  staPortBpduGuardAutoRecovery EnabledStatus
  staPortBpduGuardAutoRecoveryInterval Unsigned32

XstInstanceCfgEntry  
SEQUENCE    
  xstInstanceCfgIndex Integer32
  xstInstanceCfgPriority Integer32
  xstInstanceCfgTimeSinceTopologyChange TimeTicks
  xstInstanceCfgTopChanges Integer32
  xstInstanceCfgDesignatedRoot BridgeId
  xstInstanceCfgRootCost Integer32
  xstInstanceCfgRootPort Integer32
  xstInstanceCfgMaxAge Timeout
  xstInstanceCfgHelloTime Timeout
  xstInstanceCfgHoldTime Timeout
  xstInstanceCfgForwardDelay Timeout
  xstInstanceCfgBridgeMaxAge Timeout
  xstInstanceCfgBridgeHelloTime Timeout
  xstInstanceCfgBridgeForwardDelay Timeout
  xstInstanceCfgTxHoldCount Integer32
  xstInstanceCfgPathCostMethod StaPathCostMode

XstInstancePortEntry  
SEQUENCE    
  xstInstancePortInstance Integer32
  xstInstancePortPort Integer32
  xstInstancePortPriority Integer32
  xstInstancePortState INTEGER
  xstInstancePortEnable EnabledStatus
  xstInstancePortPathCost Integer32
  xstInstancePortDesignatedRoot BridgeId
  xstInstancePortDesignatedCost Integer32
  xstInstancePortDesignatedBridge BridgeId
  xstInstancePortDesignatedPort OCTET STRING
  xstInstancePortForwardTransitions Counter32
  xstInstancePortPortRole INTEGER
  xstInstancePortAdminPathCost Integer32
  xstInstancePortOperPathCost Integer32

MstInstanceEditEntry  
SEQUENCE    
  mstInstanceEditIndex Integer32
  mstInstanceEditVlansMap OCTET STRING
  mstInstanceEditVlansMap2k OCTET STRING
  mstInstanceEditVlansMap3k OCTET STRING
  mstInstanceEditVlansMap4k OCTET STRING
  mstInstanceEditRemainingHops Integer32

MstInstanceOperEntry  
SEQUENCE    
  mstInstanceOperIndex Integer32
  mstInstanceOperVlansMap OCTET STRING
  mstInstanceOperVlansMap2k OCTET STRING
  mstInstanceOperVlansMap3k OCTET STRING
  mstInstanceOperVlansMap4k OCTET STRING

StaLoopbackDetectionPortEntry  
SEQUENCE    
  staLoopbackDetectionPortIfIndex InterfaceIndex
  staLoopbackDetectionPortStatus EnabledStatus
  staLoopbackDetectionPortTrapStatus EnabledStatus
  staLoopbackDetectionPortReleaseMode INTEGER
  staLoopbackDetectionPortRelease INTEGER

MirrorEntry  
SEQUENCE    
  mirrorDestinationPort Integer32
  mirrorSourcePort Integer32
  mirrorType INTEGER
  mirrorStatus ValidStatus

VlanMirrorEntry  
SEQUENCE    
  vlanMirrorDestinationPort Integer32
  vlanMirrorSourceVlan Integer32
  vlanMirrorStatus ValidStatus

IgmpSnoopRouterCurrentEntry  
SEQUENCE    
  igmpSnoopRouterCurrentVlanIndex Unsigned32
  igmpSnoopRouterCurrentPorts PortList
  igmpSnoopRouterCurrentStatus PortList

IgmpSnoopRouterStaticEntry  
SEQUENCE    
  igmpSnoopRouterStaticVlanIndex Unsigned32
  igmpSnoopRouterStaticPorts PortList
  igmpSnoopRouterStaticStatus ValidStatus

IgmpSnoopMulticastCurrentEntry  
SEQUENCE    
  igmpSnoopMulticastCurrentVlanIndex Unsigned32
  igmpSnoopMulticastCurrentIpAddress IpAddress
  igmpSnoopMulticastCurrentPorts PortList
  igmpSnoopMulticastCurrentStatus PortList

IgmpSnoopMulticastStaticEntry  
SEQUENCE    
  igmpSnoopMulticastStaticVlanIndex Unsigned32
  igmpSnoopMulticastStaticIpAddress IpAddress
  igmpSnoopMulticastStaticPorts PortList
  igmpSnoopMulticastStaticStatus ValidStatus

IgmpSnoopCurrentVlanEntry  
SEQUENCE    
  igmpSnoopCurrentVlanIndex Unsigned32
  igmpSnoopCurrentVlanImmediateLeave EnabledStatus

IgmpSnoopProfileEntry  
SEQUENCE    
  igmpSnoopProfileId Unsigned32
  igmpSnoopProfileAction INTEGER
  igmpSnoopProfileStatus ValidStatus

IgmpSnoopProfileRangeEntry  
SEQUENCE    
  igmpSnoopProfileRangeProfileId Unsigned32
  igmpSnoopProfileRangeInetAddressType InetAddressType
  igmpSnoopProfileRangeStartInetAddress InetAddress
  igmpSnoopProfileRangeEndInetAddress InetAddress
  igmpSnoopProfileRangeAction INTEGER

IgmpSnoopFilterPortEntry  
SEQUENCE    
  igmpSnoopFilterPortIndex Unsigned32
  igmpSnoopFilterPortProfileId Integer32

IgmpSnoopThrottlePortEntry  
SEQUENCE    
  igmpSnoopThrottlePortIndex Unsigned32
  igmpSnoopThrottlePortRunningStatus INTEGER
  igmpSnoopThrottlePortAction INTEGER
  igmpSnoopThrottlePortMaxGroups Integer32
  igmpSnoopThrottlePortCurrentGroups Integer32

IgmpSnoopPortEntry  
SEQUENCE    
  igmpSnoopPortIndex Unsigned32
  igmpSnoopQueryDrop EnabledStatus

IgmpSnoopPortVlanEntry  
SEQUENCE    
  igmpSnoopPortVlanPortIndex Unsigned32
  igmpSnoopPortVlanVlanIndex Unsigned32
  igmpSnoopPortVlanQueryDrop EnabledStatus

NetConfigEntry  
SEQUENCE    
  netConfigIfIndex Integer32
  netConfigIPAddress IpAddress
  netConfigSubnetMask IpAddress
  netConfigPrimaryInterface INTEGER
  netConfigUnnumbered INTEGER
  netConfigStatus RowStatus

DhcpcInterfaceEntry  
SEQUENCE    
  dhcpcIfIndex Integer32
  dhcpcIfClientIdMode INTEGER
  dhcpcIfClientId OCTET STRING

DhcpOption82RelayServerAddrEntry  
SEQUENCE    
  dhcpOption82RelayServerAddrIndex Integer32
  dhcpOption82RelayServerAddrServerIp IpAddress

VlanEntry  
SEQUENCE    
  vlanIndex Unsigned32
  vlanAddressMethod INTEGER

VlanPortEntry  
SEQUENCE    
  vlanPortIndex Integer32
  vlanPortMode INTEGER
  vlanPortPrivateVlanType INTEGER

ProtocolVlanEntry  
SEQUENCE    
  protocolVlanGroupId Integer32
  protocolVlanGroupVid Integer32

VlanDot1qTunnelPortEntry  
SEQUENCE    
  vlanDot1qTunnelPortIndex Integer32
  vlanDot1qTunnelPortMode INTEGER
  vlanDot1qTunnelPortEtherType Unsigned32

VoiceVlanOuiEntry  
SEQUENCE    
  voiceVlanOuiAddress MacAddress
  voiceVlanOuiMask MacAddress
  voiceVlanOuiDescription DisplayString
  voiceVlanOuiStatus ValidStatus

VoiceVlanPortEntry  
SEQUENCE    
  voiceVlanPortIfIndex Integer32
  voiceVlanPortMode INTEGER
  voiceVlanPortSecurity EnabledStatus
  voiceVlanPortPriority INTEGER
  voiceVlanPortRuleOui EnabledStatus
  voiceVlanPortRuleLldp EnabledStatus

MacVlanEntry  
SEQUENCE    
  macVlanMacAddress MacAddress
  macVlanId Integer32
  macVlanStatus ValidStatus
  macVlanMacMask MacAddress

SubnetVlanEntry  
SEQUENCE    
  subnetVlanIpAddress IpAddress
  subnetVlanMask IpAddress
  subnetVlanId Integer32
  subnetVlanPriority Integer32
  subnetVlanStatus ValidStatus

VlanL2ProtocolTunnelPortEntry  
SEQUENCE    
  vlanL2ptPortIndex Integer32
  vlanL2ptPortSta EnabledStatus
  vlanL2ptPortLldp EnabledStatus
  vlanL2ptPortCdp EnabledStatus
  vlanL2ptPortVtp EnabledStatus
  vlanL2ptPortPvst EnabledStatus

PrioIpDscpEntry  
SEQUENCE    
  prioIpDscpPort Integer32
  prioIpDscpValue Integer32
  prioIpDscpCos Integer32

PrioWrrEntry  
SEQUENCE    
  prioWrrTrafficClass Integer32
  prioWrrWeight Integer32

TrapDestEntry  
SEQUENCE    
  trapDestAddress IpAddress
  trapDestCommunity OCTET STRING
  trapDestStatus ValidStatus
  trapDestVersion INTEGER
  trapDestUdpPort Integer32

RateLimitPortEntry  
SEQUENCE    
  rlPortIndex Integer32
  rlPortInputStatus EnabledStatus
  rlPortOutputStatus EnabledStatus
  rlPortInputLimitInKilo Integer32
  rlPortOutputLimitInKilo Integer32

DiffServPortEntry  
SEQUENCE    
  diffServPortIfIndex Integer32
  diffServPortPolicyMapIndex Integer32
  diffServPortIngressIpAclIndex Integer32
  diffServPortIngressMacAclIndex Integer32
  diffServPortIngressIpv6AclIndex Integer32

DiffServPolicyMapEntry  
SEQUENCE    
  diffServPolicyMapIndex Integer32
  diffServPolicyMapName DisplayString
  diffServPolicyMapDescription DisplayString
  diffServPolicyMapElementIndexList OCTET STRING
  diffServPolicyMapStatus RowStatus

DiffServPolicyMapElementEntry  
SEQUENCE    
  diffServPolicyMapElementIndex Integer32
  diffServPolicyMapElementClassMapIndex Integer32
  diffServPolicyMapElementMeterIndex Integer32
  diffServPolicyMapElementActionIndex Integer32
  diffServPolicyMapElementStatus RowStatus

DiffServClassMapEntry  
SEQUENCE    
  diffServClassMapIndex Integer32
  diffServClassMapName DisplayString
  diffServClassMapDescription DisplayString
  diffServClassMapMatchType INTEGER
  diffServClassMapElementIndexTypeList OCTET STRING
  diffServClassMapElementIndexList OCTET STRING
  diffServClassMapStatus RowStatus

DiffServAclEntry  
SEQUENCE    
  diffServAclIndex Integer32
  diffServAclName DisplayString
  diffServAclType INTEGER
  diffServAclAceIndexList OCTET STRING
  diffServAclStatus RowStatus

DiffServIpAceEntry  
SEQUENCE    
  diffServIpAceIndex Integer32
  diffServIpAceType INTEGER
  diffServIpAceAccess INTEGER
  diffServIpAceSourceIpAddr IpAddress
  diffServIpAceSourceIpAddrBitmask IpAddress
  diffServIpAceDestIpAddr IpAddress
  diffServIpAceDestIpAddrBitmask IpAddress
  diffServIpAceProtocol Integer32
  diffServIpAcePrec Integer32
  diffServIpAceTos Integer32
  diffServIpAceDscp Integer32
  diffServIpAceSourcePortOp INTEGER
  diffServIpAceMinSourcePort Integer32
  diffServIpAceSourcePortBitmask Integer32
  diffServIpAceDestPortOp INTEGER
  diffServIpAceMinDestPort Integer32
  diffServIpAceDestPortBitmask Integer32
  diffServIpAceControlCode Integer32
  diffServIpAceControlCodeBitmask Integer32
  diffServIpAceStatus RowStatus

DiffServMacAceEntry  
SEQUENCE    
  diffServMacAceIndex Integer32
  diffServMacAceAccess INTEGER
  diffServMacAcePktformat INTEGER
  diffServMacAceSourceMacAddr MacAddress
  diffServMacAceSourceMacAddrBitmask MacAddress
  diffServMacAceDestMacAddr MacAddress
  diffServMacAceDestMacAddrBitmask MacAddress
  diffServMacAceVidOp INTEGER
  diffServMacAceMinVid Integer32
  diffServMacAceVidBitmask Integer32
  diffServMacAceEtherTypeOp INTEGER
  diffServMacAceEtherTypeBitmask Integer32
  diffServMacAceMinEtherType Integer32
  diffServMacAceCosOp INTEGER
  diffServMacAceCosBitmask INTEGER
  diffServMacAceMinCos INTEGER
  diffServMacAceStatus RowStatus

DiffServActionEntry  
SEQUENCE    
  diffServActionIndex Integer32
  diffServActionList BITS
  diffServActionPktNewPri Integer32
  diffServActionPktNewDscp Integer32
  diffServActionRedPktNewDscp Integer32
  diffServActionRedDrop EnabledStatus
  diffServActionStatus RowStatus

DiffServMeterEntry  
SEQUENCE    
  diffServMeterIndex Integer32
  diffServMeterModel INTEGER
  diffServMeterRate Integer32
  diffServMeterBurstSize Integer32
  diffServMeterInterval Integer32
  diffServMeterStatus RowStatus

DiffServIpv6AceEntry  
SEQUENCE    
  diffServIpv6AceIndex Integer32
  diffServIpv6AceType INTEGER
  diffServIpv6AceAccess INTEGER
  diffServIpv6AceSourceIpAddr OCTET STRING
  diffServIpv6AceSourceIpAddrPrefixLen Integer32
  diffServIpv6AceDestIpAddr OCTET STRING
  diffServIpv6AceDestIpAddrPrefixLen Integer32
  diffServIpv6AceDscp Integer32
  diffServIpv6AceStatus RowStatus

DiffServArpAceEntry  
SEQUENCE    
  diffServArpAceIndex Integer32
  diffServArpAceAction INTEGER
  diffServArpAcePktType INTEGER
  diffServArpAceSourceIpAddr IpAddress
  diffServArpAceSourceIpAddrBitmask IpAddress
  diffServArpAceDestIpAddr IpAddress
  diffServArpAceDestIpAddrBitmask IpAddress
  diffServArpAceSourceMacAddr OCTET STRING
  diffServArpAceSourceMacAddrBitmask OCTET STRING
  diffServArpAceDestMacAddr OCTET STRING
  diffServArpAceDestMacAddrBitmask OCTET STRING
  diffServArpAceLogStatus EnabledStatus
  diffServArpAceStatus RowStatus

DiffServArpEntry  
SEQUENCE    
  diffServArpAclName DisplayString

PrivateVlanVlanEntry  
SEQUENCE    
  privateVlanVlanIndex Integer32
  privateVlanVlanType INTEGER
  privateVlanAssoicatedPrimaryVlan Integer32

PrivateVlanPrivatePortEntry  
SEQUENCE    
  privateVlanPrivatePortIfIndex Integer32
  privateVlanPrivatePortSecondaryVlan Integer32

PrivateVlanPromPortEntry  
SEQUENCE    
  privateVlanPromPortIfIndex Integer32
  privateVlanPromPortPrimaryVlanId Integer32
  privateVlanPromPortSecondaryRemap OCTET STRING
  privateVlanPromPortSecondaryRemap2k OCTET STRING
  privateVlanPromPortSecondaryRemap3k OCTET STRING
  privateVlanPromPortSecondaryRemap4k OCTET STRING

PrivateVlanSessionEntry  
SEQUENCE    
  privateVlanSessionId INTEGER
  privateVlanSessionUplinkPorts PortList
  privateVlanSessionDownlinkPorts PortList
  privateVlanSessionStatus ValidStatus

PortSecPortEntry  
SEQUENCE    
  portSecPortIndex Integer32
  portSecPortStatus EnabledStatus
  portSecAction INTEGER
  portSecMaxMacCount Integer32

RadiusServerEntry  
SEQUENCE    
  radiusServerIndex Integer32
  radiusServerAddress IpAddress
  radiusServerAuthPortNumber Integer32
  radiusServerAcctPortNumber Integer32
  radiusServerKey DisplayString
  radiusServerRetransmit Integer32
  radiusServerTimeout Integer32
  radiusServerStatus ValidStatus

TacacsPlusServerEntry  
SEQUENCE    
  tacacsPlusServerIndex Integer32
  tacacsPlusServerAddress IpAddress
  tacacsPlusServerPortNumber Integer32
  tacacsPlusServerKey DisplayString
  tacacsPlusServerStatus ValidStatus
  tacacsPlusServerRetransmit Integer32
  tacacsPlusServerTimeout Integer32

SshConnInfoEntry  
SEQUENCE    
  sshConnID Integer32
  sshConnMajorVersion Integer32
  sshConnMinorVersion Integer32
  sshConnStatus INTEGER
  sshConnEncryptionType INTEGER
  sshConnUserName DisplayString
  sshDisconnect INTEGER
  sshConnEncryptionTypeStr DisplayString

SshUserEntry  
SEQUENCE    
  sshUserName DisplayString
  sshUserRsaKey1 KeySegment
  sshUserRsaKey2 KeySegment
  sshUserRsaKey3 KeySegment
  sshUserRsaKey4 KeySegment
  sshUserRsaKey5 KeySegment
  sshUserRsaKey6 KeySegment
  sshUserRsaKey7 KeySegment
  sshUserRsaKey8 KeySegment
  sshUserDsaKey1 KeySegment
  sshUserDsaKey2 KeySegment
  sshUserDsaKey3 KeySegment
  sshUserDsaKey4 KeySegment
  sshUserDsaKey5 KeySegment
  sshUserDsaKey6 KeySegment
  sshUserDsaKey7 KeySegment
  sshUserDsaKey8 KeySegment
  sshUserKeyDelAction INTEGER

AaaMethodEntry  
SEQUENCE    
  aaaMethodIndex Integer32
  aaaMethodName DisplayString
  aaaMethodGroupName DisplayString
  aaaMethodMode INTEGER
  aaaMethodStatus ValidStatus
  aaaMethodClientType INTEGER
  aaaMethodPrivilegeLevel INTEGER

AaaRadiusGroupEntry  
SEQUENCE    
  aaaRadiusGroupIndex Integer32
  aaaRadiusGroupServerBitMap OCTET STRING
  aaaRadiusGroupName DisplayString
  aaaRadiusGroupStatus ValidStatus

AaaTacacsPlusGroupEntry  
SEQUENCE    
  aaaTacacsPlusGroupIndex Integer32
  aaaTacacsPlusGroupServerBitMap OCTET STRING
  aaaTacacsPlusGroupName DisplayString
  aaaTacacsPlusGroupStatus ValidStatus

AaaAccountEntry  
SEQUENCE    
  aaaAccountIfIndex Integer32
  aaaAccountMethodName DisplayString
  aaaAccountProtocol INTEGER
  aaaAccountStatus ValidStatus

AaaCommandPrivilegesEntry  
SEQUENCE    
  aaaCommandPrivilegesLevel INTEGER
  aaaCommandPrivilegesInterfaceIndex INTEGER
  aaaCommandPrivilegesMethodName DisplayString

AaaAccExecEntry  
SEQUENCE    
  aaaAccExecIndex INTEGER
  aaaAccExecMethodName DisplayString

IpFilterSnmpEntry  
SEQUENCE    
  ipFilterSnmpStartAddress IpAddress
  ipFilterSnmpEndAddress IpAddress
  ipFilterSnmpStatus ValidStatus

IpFilterHTTPEntry  
SEQUENCE    
  ipFilterHTTPStartAddress IpAddress
  ipFilterHTTPEndAddress IpAddress
  ipFilterHTTPStatus ValidStatus

IpFilterTelnetEntry  
SEQUENCE    
  ipFilterTelnetStartAddress IpAddress
  ipFilterTelnetEndAddress IpAddress
  ipFilterTelnetStatus ValidStatus

Dot1xAuthConfigExtEntry  
SEQUENCE    
  dot1xAuthConfigExtOperMode INTEGER
  dot1xAuthConfigExtMultiHostMaxCnt Integer32
  dot1xAuthConfigExtPortIntrusionAction INTEGER

Dot1xSuppConfigPortEntry  
SEQUENCE    
  dot1xSuppConfigPortIndex Integer32
  dot1xSuppConfigPortStatus EnabledStatus

NetworkAccessPortEntry  
SEQUENCE    
  networkAccessPortPortIndex Integer32
  networkAccessPortMaxMacCount INTEGER
  networkAccessPortMode EnabledStatus
  networkAccessPortMacFilter INTEGER
  networkAccessPortGuestVlan INTEGER
  networkAccessPortLinkDetectionStatus EnabledStatus
  networkAccessPortLinkDetectionMode INTEGER
  networkAccessPortLinkDetectionAciton INTEGER
  networkAccessPortDynamicQos EnabledStatus

NetworkAccessMacAddressEntry  
SEQUENCE    
  networkAccessMacAddressAddress MacAddress
  networkAccessMacAddressPort INTEGER
  networkAccessMacAddressInetAddressType InetAddressType
  networkAccessMacAddressRadiusServerInetAddress InetAddress
  networkAccessMacAddressTime DisplayString
  networkAccessMacAddressAttribute INTEGER

NetworkAccessMacFilterWithMaskEntry  
SEQUENCE    
  networkAccessMacFilterWithMaskID INTEGER
  networkAccessMacFilterWithMaskMacAddress MacAddress
  networkAccessMacFilterWithMaskMacAddressMask MacAddress
  networkAccessMacFilterWithMaskStatus INTEGER

MacAuthPortEntry  
SEQUENCE    
  macAuthPortIndex Integer32
  macAuthPortMaxMacCount INTEGER
  macAuthPortIntrusionAction INTEGER

WebAuthPortConfigEntry  
SEQUENCE    
  webAuthPortConfigPortIndex INTEGER
  webAuthPortConfigStatus INTEGER
  webAuthPortConfigAuthenticatedHostCount INTEGER

WebAuthPortInfoEntry  
SEQUENCE    
  webAuthPortInfoPortIndex INTEGER
  webAuthPortInfoPortAuthSuccessIndex INTEGER
  webAuthPortInfoInetAddressType InetAddressType
  webAuthPortInfoInetAddress InetAddress
  webAuthPortInfoRemainingSessiontime INTEGER
  webAuthPortInfoStatus INTEGER

RemoteLogServerEntry  
SEQUENCE    
  remoteLogServerIp IpAddress
  remoteLogServerStatus ValidStatus

SmtpServerIpEntry  
SEQUENCE    
  smtpServerIp IpAddress
  smtpServerIpStatus ValidStatus

SmtpDestEMailEntry  
SEQUENCE    
  smtpDestEMail DisplayString
  smtpDestEMailStatus ValidStatus

SntpServerEntry  
SEQUENCE    
  sntpServerIndex Integer32
  sntpServerIpAddress IpAddress

NtpServerEntry  
SEQUENCE    
  ntpServerIpAddress IpAddress
  ntpServerVersion Integer32
  ntpServerKeyId Integer32
  ntpServerStatus INTEGER

NtpAuthKeyEntry  
SEQUENCE    
  ntpAuthKeyId Integer32
  ntpAuthKeyWord OCTET STRING
  ntpAuthKeyStatus INTEGER

FileInfoEntry  
SEQUENCE    
  fileInfoUnitID Integer32
  fileInfoFileName DisplayString
  fileInfoFileType INTEGER
  fileInfoIsStartUp TruthValue
  fileInfoFileSize Integer32
  fileInfoCreationTime DisplayString
  fileInfoDelete INTEGER

FileAutoDownloadResultEntry  
SEQUENCE    
  fileAutoDownloadResultUnitID Integer32
  fileAutoDownloadResultAction INTEGER
  fileAutoDownloadResultStatus FileCopyStatus

DnsHostEntry  
SEQUENCE    
  dnsHostName DisplayString
  dnsHostIndex Integer32
  dnsHostIp IpAddress

DnsDomainListEntry  
SEQUENCE    
  dnsDomainListName DisplayString
  dnsDomainListStatus ValidStatus

DnsNameServerEntry  
SEQUENCE    
  dnsNameServerIndex Integer32
  dnsNameServerIp IpAddress

DnsCacheEntry  
SEQUENCE    
  dnsCacheIndex Integer32
  dnsCacheFlag Integer32
  dnsCacheType INTEGER
  dnsCacheIp IpAddress
  dnsCacheTtl Integer32
  dnsCacheDomain DisplayString

McastStormEntry  
SEQUENCE    
  mcastStormIfIndex Integer32
  mcastStormStatus EnabledStatus
  mcastStormOctetRate Integer32

BcastStormEntry  
SEQUENCE    
  bcastStormIfIndex Integer32
  bcastStormStatus EnabledStatus
  bcastStormOctetRate Integer32

UnknownUcastStormEntry  
SEQUENCE    
  unknownUcastStormIfIndex Integer32
  unknownUcastStormStatus EnabledStatus
  unknownUcastStormOctetRate INTEGER

AtcBcastStormEntry  
SEQUENCE    
  atcBcastStormIfIndex Integer32
  atcBcastStormEnable EnabledStatus
  atcBcastStormAutoRelease EnabledStatus
  atcBcastStormSampleType INTEGER
  atcBcastStormCurrentTrafficRate Integer32
  atcBcastStormAlarmFireThreshold Integer32
  atcBcastStormAlarmClearThreshold Integer32
  atcBcastStormTcAction INTEGER
  atcBcastStormAlarmFireTrapStatus EnabledStatus
  atcBcastStormAlarmClearTrapStatus EnabledStatus
  atcBcastStormTcApplyTrapStatus EnabledStatus
  atcBcastStormTcReleaseTrapStatus EnabledStatus

AtcMcastStormEntry  
SEQUENCE    
  atcMcastStormIfIndex Integer32
  atcMcastStormEnable EnabledStatus
  atcMcastStormAutoRelease EnabledStatus
  atcMcastStormSampleType INTEGER
  atcMcastStormCurrentTrafficRate Integer32
  atcMcastStormAlarmFireThreshold Integer32
  atcMcastStormAlarmClearThreshold Integer32
  atcMcastStormTcAction INTEGER
  atcMcastStormAlarmFireTrapStatus EnabledStatus
  atcMcastStormAlarmClearTrapStatus EnabledStatus
  atcMcastStormTcApplyTrapStatus EnabledStatus
  atcMcastStormTcReleaseTrapStatus EnabledStatus

MvrGroupStaticEntry  
SEQUENCE    
  mvrGroupStaticAddress IpAddress
  mvrGroupStaticPorts PortList
  mvrGroupStaticStatus INTEGER

MvrGroupCurrentEntry  
SEQUENCE    
  mvrGroupCurrentAddress IpAddress
  mvrGroupCurrentPorts PortList
  mvrGroupCurrentReceiverVlan Integer32

MvrPortEntry  
SEQUENCE    
  mvrIfIndex InterfaceIndex
  mvrPortType INTEGER
  mvrPortImmediateLeave EnabledStatus
  mvrPortActive INTEGER

MvrReceiverGroupEntry  
SEQUENCE    
  mvrReceiverGroupId IpAddress
  mvrReceiverGroupActive INTEGER

MvrReceiverGroupStaticEntry  
SEQUENCE    
  mvrReceiverGroupStaticAddress IpAddress
  mvrReceiverGroupStaticPorts PortList

MvrReceiverGroupCurrentEntry  
SEQUENCE    
  mvrReceiverGroupCurrentAddress IpAddress
  mvrReceiverGroupCurrentPorts PortList

MvrGroupCtlEntry  
SEQUENCE    
  mvrGroupStartIPAddress IpAddress
  mvrGroupEndIPAddress IpAddress
  mvrGroupCtlAction Integer32

MvrReceiverGroupCtlEntry  
SEQUENCE    
  mvrReceiverGroupIPAddress IpAddress
  mvrReceiverGroupMask IpAddress
  mvrReceiverGroupCtlAction Integer32

DhcpSnoopVlanConfigEntry  
SEQUENCE    
  dhcpSnoopVlanIndex VlanIndex
  dhcpSnoopVlanEnable EnabledStatus

DhcpSnoopPortConfigEntry  
SEQUENCE    
  dhcpSnoopPortIfIndex InterfaceIndex
  dhcpSnoopPortTrustEnable EnabledStatus
  dhcpSnoopPortCircuitIDMode INTEGER
  dhcpSnoopPortCircuitIDString OCTET STRING

DhcpSnoopBindingsEntry  
SEQUENCE    
  dhcpSnoopBindingsVlanIndex VlanIndex
  dhcpSnoopBindingsMacAddress MacAddress
  dhcpSnoopBindingsAddrType InetAddressType
  dhcpSnoopBindingsEntryType INTEGER
  dhcpSnoopBindingsIpAddress IpAddress
  dhcpSnoopBindingsPortIfIndex InterfaceIndex
  dhcpSnoopBindingsLeaseTime Unsigned32

ClusterCandidateEntry  
SEQUENCE    
  clusterCandidateMacAddr MacAddress
  clusterCandidateDesc DisplayString
  clusterCandidateRole INTEGER

ClusterMemberEntry  
SEQUENCE    
  clusterMemberId Unsigned32
  clusterMemberMacAddr MacAddress
  clusterMemberDesc DisplayString
  clusterMemberActive INTEGER

IpSrcGuardConfigEntry  
SEQUENCE    
  ipSrcGuardPortIfIndex InterfaceIndex
  ipSrcGuardMode INTEGER

IpSrcGuardAddrEntry  
SEQUENCE    
  ipSrcGuardBindingsVlanIndex VlanIndex
  ipSrcGuardBindingsMacAddress MacAddress
  ipSrcGuardBindingsAddrType InetAddressType
  ipSrcGuardBindingsEntryType INTEGER
  ipSrcGuardBindingsIpAddress IpAddress
  ipSrcGuardBindingsPortIfIndex InterfaceIndex
  ipSrcGuardBindingsLeaseTime Unsigned32
  ipSrcGuardBindingsStatus RowStatus

SFlowPortEntry  
SEQUENCE    
  sFlowPortIndex Integer32
  sFlowPortStatus EnabledStatus

DaiVlanEntry  
SEQUENCE    
  daiVlanIndex VlanIndex
  daiVlanStatus EnabledStatus
  daiVlanArpAclName DisplayString
  daiVlanArpAclStatus INTEGER

DaiPortEntry  
SEQUENCE    
  daiPortIfIndex InterfaceIndex
  daiPortTrustStatus EnabledStatus
  daiPortRateLimit Unsigned32

DaiLogEntry  
SEQUENCE    
  daiLogIndex Integer32
  daiLogVlan VlanIndex
  daiLogPort InterfaceIndex
  daiLogSrcIpAddress IpAddress
  daiLogDestIpAddress IpAddress
  daiLogSrcMacAddress MacAddress
  daiLogDestMacAddress MacAddress

ErpsDomainEntry  
SEQUENCE    
  erpsDomainIndex Integer32
  erpsDomainName DisplayString
  erpsDomainMegLevel INTEGER
  erpsDomainNodeId MacAddress
  erpsDomainWestRingPort Integer32
  erpsDomainEastRingPort Integer32
  erpsDomainRplOwner INTEGER
  erpsDomainRplPort INTEGER
  erpsDomainGuardTimer Integer32
  erpsDomainHoldoffTimer Integer32
  erpsDomainWtrTimer Integer32
  erpsDomainControlVlanID Integer32
  erpsDomainNodeState INTEGER
  erpsDomainWestRingPortState INTEGER
  erpsDomainEastRingPortState INTEGER
  erpsDomainRowStatus RowStatus
  erpsDomainMajorDomainIndex Integer32
  erpsDomainPropagateTC INTEGER
  erpsDomainWestMepId Integer32
  erpsDomainEastMepId Integer32
  erpsDomainNonErpsDevProtect INTEGER

LbdPortEntry  
SEQUENCE    
  lbdPortIfIndex InterfaceIndex
  lbdPortAdminState INTEGER
  lbdPortOperState INTEGER
  lbdPortLoopedVlan OCTET STRING

Defined Values

accton 7.1.259
OBJECT IDENTIFIER    

snmpMgt 7.1.259.6
OBJECT IDENTIFIER    

cheetahSwitchMgt 7.1.259.6.10
OBJECT IDENTIFIER    

es3528moMIB 7.1.259.6.10.94
The MIB module for ES3528MO.
MODULE-IDENTITY    

es3528moMIBObjects 7.1.259.6.10.94.1
OBJECT IDENTIFIER    

es3528moNotifications 7.1.259.6.10.94.2
OBJECT IDENTIFIER    

es3528moConformance 7.1.259.6.10.94.3
OBJECT IDENTIFIER    

switchMgt 7.1.259.6.10.94.1.1
OBJECT IDENTIFIER    

portMgt 7.1.259.6.10.94.1.2
OBJECT IDENTIFIER    

trunkMgt 7.1.259.6.10.94.1.3
OBJECT IDENTIFIER    

lacpMgt 7.1.259.6.10.94.1.4
OBJECT IDENTIFIER    

staMgt 7.1.259.6.10.94.1.5
OBJECT IDENTIFIER    

restartMgt 7.1.259.6.10.94.1.7
OBJECT IDENTIFIER    

mirrorMgt 7.1.259.6.10.94.1.8
OBJECT IDENTIFIER    

igmpSnoopMgt 7.1.259.6.10.94.1.9
OBJECT IDENTIFIER    

ipMgt 7.1.259.6.10.94.1.10
OBJECT IDENTIFIER    

vlanMgt 7.1.259.6.10.94.1.12
OBJECT IDENTIFIER    

priorityMgt 7.1.259.6.10.94.1.13
OBJECT IDENTIFIER    

trapDestMgt 7.1.259.6.10.94.1.14
OBJECT IDENTIFIER    

qosMgt 7.1.259.6.10.94.1.16
OBJECT IDENTIFIER    

securityMgt 7.1.259.6.10.94.1.17
OBJECT IDENTIFIER    

sysLogMgt 7.1.259.6.10.94.1.19
OBJECT IDENTIFIER    

lineMgt 7.1.259.6.10.94.1.20
OBJECT IDENTIFIER    

sysTimeMgt 7.1.259.6.10.94.1.23
OBJECT IDENTIFIER    

fileMgt 7.1.259.6.10.94.1.24
OBJECT IDENTIFIER    

dnsMgt 7.1.259.6.10.94.1.26
OBJECT IDENTIFIER    

stormMgt 7.1.259.6.10.94.1.33
OBJECT IDENTIFIER    

sysResourceMgt 7.1.259.6.10.94.1.39
OBJECT IDENTIFIER    

mvrMgt 7.1.259.6.10.94.1.44
OBJECT IDENTIFIER    

dhcpSnoopMgt 7.1.259.6.10.94.1.46
OBJECT IDENTIFIER    

clusterMgt 7.1.259.6.10.94.1.47
OBJECT IDENTIFIER    

ipSrcGuardMgt 7.1.259.6.10.94.1.48
OBJECT IDENTIFIER    

upnpMgt 7.1.259.6.10.94.1.49
OBJECT IDENTIFIER    

sFlowMgt 7.1.259.6.10.94.1.55
OBJECT IDENTIFIER    

dynamicArpInspectionMgt 7.1.259.6.10.94.1.56
OBJECT IDENTIFIER    

erpsMgt 7.1.259.6.10.94.1.62
OBJECT IDENTIFIER    

lbdMgt 7.1.259.6.10.94.1.63
OBJECT IDENTIFIER    

switchNumber 7.1.259.6.10.94.1.1.2
The total number of switches present on this system.
OBJECT-TYPE    
  Integer32  

switchInfoTable 7.1.259.6.10.94.1.1.3
Table of descriptive and status information about the switch units in this system.
OBJECT-TYPE    
  SEQUENCE OF  
    SwitchInfoEntry

switchInfoEntry 7.1.259.6.10.94.1.1.3.1
Table providing descriptions and status information for switch units.
OBJECT-TYPE    
  SwitchInfoEntry  

swUnitIndex 7.1.259.6.10.94.1.1.3.1.1
This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber.
OBJECT-TYPE    
  Integer32  

swHardwareVer 7.1.259.6.10.94.1.1.3.1.2
Hardware version of the main board.
OBJECT-TYPE    
  DisplayString Size(0..20)  

swMicrocodeVer 7.1.259.6.10.94.1.1.3.1.3
Microcode version of the main board.
OBJECT-TYPE    
  DisplayString Size(0..20)  

swLoaderVer 7.1.259.6.10.94.1.1.3.1.4
Loader version of the main board.
OBJECT-TYPE    
  DisplayString Size(0..20)  

swBootRomVer 7.1.259.6.10.94.1.1.3.1.5
Boot ROM code version of the main board.
OBJECT-TYPE    
  DisplayString Size(0..20)  

swOpCodeVer 7.1.259.6.10.94.1.1.3.1.6
Operation code version of the main board.
OBJECT-TYPE    
  DisplayString Size(0..20)  

swPortNumber 7.1.259.6.10.94.1.1.3.1.7
The number of ports on this switch.
OBJECT-TYPE    
  Integer32  

swPowerStatus 7.1.259.6.10.94.1.1.3.1.8
Indicates the switch using internalPower(1), redundantPower(2) or both(3)
OBJECT-TYPE    
  INTEGER internalPower(1), redundantPower(2), internalAndRedundantPower(3)  

swRoleInSystem 7.1.259.6.10.94.1.1.3.1.9
Indicates the switch is master(1), backupMaster(2) or slave(3) in this system.
OBJECT-TYPE    
  INTEGER master(1), backupMaster(2), slave(3)  

swSerialNumber 7.1.259.6.10.94.1.1.3.1.10
Serial number of the switch.
OBJECT-TYPE    
  DisplayString Size(0..80)  

swServiceTag 7.1.259.6.10.94.1.1.3.1.13
Service tag serial-number of the switch.
OBJECT-TYPE    
  DisplayString Size(0..80)  

swModelNumber 7.1.259.6.10.94.1.1.3.1.14
Model number of the switch.
OBJECT-TYPE    
  DisplayString Size(0..15)  

swEpldVer 7.1.259.6.10.94.1.1.3.1.15
The EPLD version of the switch.
OBJECT-TYPE    
  DisplayString Size(0..20)  

switchOperState 7.1.259.6.10.94.1.1.4
Global operation state of the switch.
OBJECT-TYPE    
  INTEGER other(1), unknown(2), ok(3), noncritical(4), critical(5), nonrecoverable(6)  

switchProductId 7.1.259.6.10.94.1.1.5
OBJECT IDENTIFIER    

swProdName 7.1.259.6.10.94.1.1.5.1
The product name of this switch.
OBJECT-TYPE    
  DisplayString Size(0..127)  

swProdManufacturer 7.1.259.6.10.94.1.1.5.2
The product manufacturer of this switch.
OBJECT-TYPE    
  DisplayString Size(0..127)  

swProdDescription 7.1.259.6.10.94.1.1.5.3
The product description of this switch.
OBJECT-TYPE    
  DisplayString Size(0..127)  

swProdVersion 7.1.259.6.10.94.1.1.5.4
The runtime code version of this switch.
OBJECT-TYPE    
  DisplayString Size(0..127)  

swProdUrl 7.1.259.6.10.94.1.1.5.5
The URL of this switch, which we can connect through a web browser.
OBJECT-TYPE    
  DisplayString Size(0..127)  

swIdentifier 7.1.259.6.10.94.1.1.5.6
A unique identifier of which switch in the chassis is currently being looked at.
OBJECT-TYPE    
  Integer32  

swChassisServiceTag 7.1.259.6.10.94.1.1.5.7
The service tag of the chassis this switch resides in.
OBJECT-TYPE    
  DisplayString Size(0..80)  

switchIndivPowerTable 7.1.259.6.10.94.1.1.6
Table about the status of individual powers.
OBJECT-TYPE    
  SEQUENCE OF  
    SwitchIndivPowerEntry

switchIndivPowerEntry 7.1.259.6.10.94.1.1.6.1
Table about the status of individual power.
OBJECT-TYPE    
  SwitchIndivPowerEntry  

swIndivPowerUnitIndex 7.1.259.6.10.94.1.1.6.1.1
This is defined as swUnitIndex.
OBJECT-TYPE    
  Integer32  

swIndivPowerIndex 7.1.259.6.10.94.1.1.6.1.2
1 means internal power, 2 means external power.
OBJECT-TYPE    
  INTEGER internalPower(1), externalPower(2)  

swIndivPowerStatus 7.1.259.6.10.94.1.1.6.1.3
notPresent(1) means not present, green(2) means up, red(3) means down.
OBJECT-TYPE    
  INTEGER notPresent(1), green(2), red(3)  

switchJumboFrameStatus 7.1.259.6.10.94.1.1.7
enable(1) means the Jumbo Frame has enabled, disabled(2) means the Jumbo Frame has disabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

amtrMgt 7.1.259.6.10.94.1.1.8
OBJECT IDENTIFIER    

amtrMacAddrAgingStatus 7.1.259.6.10.94.1.1.8.3
If this is enabled(1), the MAC address table will age out according to its timer. If this is disabled(2), the MAC address table will not age out.
OBJECT-TYPE    
  EnabledStatus  

amtrMacAddrDynamicCount 7.1.259.6.10.94.1.1.8.4
The number of dot1dTpFdbTable entries in the BRIDGE-MIB.
OBJECT-TYPE    
  Counter32  

amtrMacAddrStaticCount 7.1.259.6.10.94.1.1.8.5
The number of dot1dStaticTable entries in the BRIDGE-MIB.
OBJECT-TYPE    
  Counter32  

amtrMacAddrTotalCount 7.1.259.6.10.94.1.1.8.6
The sum of dot1dTpFdbTable and dot1dStaticTable entries.
OBJECT-TYPE    
  Counter32  

portTable 7.1.259.6.10.94.1.2.1
Table of descriptive and status information describing the configuration of each switch port. This table also contains information about each trunk.
OBJECT-TYPE    
  SEQUENCE OF  
    PortEntry

portEntry 7.1.259.6.10.94.1.2.1.1
An entry in the table, describing the configuration of one switch port or trunk.
OBJECT-TYPE    
  PortEntry  

portIndex 7.1.259.6.10.94.1.2.1.1.1
The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Integer32  

portName 7.1.259.6.10.94.1.2.1.1.2
The name of the port or trunk. This is the same as ifAlias in the IF-MIB (RFC2863 or later).
OBJECT-TYPE    
  DisplayString Size(0..64)  

portType 7.1.259.6.10.94.1.2.1.1.3
Indicates the port type of the configuration of the switch.
OBJECT-TYPE    
  INTEGER other(1), hundredBaseTX(2), hundredBaseFX(3), thousandBaseSX(4), thousandBaseLX(5), thousandBaseT(6), thousandBaseGBIC(7), thousandBaseSfp(8), hundredBaseFxScSingleMode(9), hundredBaseFxScMultiMode(10), thousandBaseCX(11), tenG(12)  

portSpeedDpxCfg 7.1.259.6.10.94.1.2.1.1.4
Configures the speed and duplex mode for a port or trunk, according to: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) - 100Mbps and full duplex mode halfDuplex1000(6) - 1000Mbps and half duplex mode fullDuplex1000(7) - 1000Mbps and full duplex mode halfDuplex10g(8) - 10g and half duplex mode fullDuplex10g(9) - 10g and full duplex mode hundredBaseTX port can be set as: halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) hundredBaseFX port can be set as: fullDuplex100(5) thousandBaseSX port can be set as: fullDuplex1000(7) thousandBaseLX port can be set as: fullDuplex1000(7) thousandBaseT port can be set as: halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) thousandBaseGBIC port can be set as: fullDuplex1000(7) thousandBaseSfp port can be set as: fullDuplex1000(7) hundredBaseFxScSingleMode port can be set as: fullDuplex100(5) hundredBaseFxScMultiMode port can be set as: fullDuplex100(5) thousandBaseCX port can be set as: fullDuplex1000(7) tenG port can be set as: halfDuplex10g(8) fullDuplex10g(9) The actual operating speed and duplex of the port is given by portSpeedDpxStatus.
OBJECT-TYPE    
  INTEGER reserved(1), halfDuplex10(2), fullDuplex10(3), halfDuplex100(4), fullDuplex100(5), halfDuplex1000(6), fullDuplex1000(7), halfDuplex10g(8), fullDuplex10g(9)  

portFlowCtrlCfg 7.1.259.6.10.94.1.2.1.1.5
(1) Flow control mechanism is enabled with tx and rx pause mechansim. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, the port uses IEEE 802.3x flow control mechanism. If the port type is hundredBaseFX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, Flow control mechanism will not function. (2) Flow control mechanism is disabled. (5) Flow control mechanism is enabled with tx pause mechanism only. (6) Flow control mechansim is enabled with rx pause mechansim only. Fast ethernet ports can be set as: enabled(1), disabled(2). Gigabit ethernet ports can be set as: enabled(1), disabled(2), tx(5), rx(6). The actual flow control mechanism is used given by portFlowCtrlStatus.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), tx(5), rx(6)  

portCapabilities 7.1.259.6.10.94.1.2.1.1.6
Port or trunk capabilities.
OBJECT-TYPE    
  BITS portCap10half(0), portCap10full(1), portCap100half(2), portCap100full(3), portCap1000half(4), portCap1000full(5), portCap10gHalf(6), portCap10gFull(7), reserved8(8), reserved9(9), reserved10(10), reserved11(11), reserved12(12), reserved13(13), portCapSym(14), portCapFlowCtrl(15)  

portAutonegotiation 7.1.259.6.10.94.1.2.1.1.7
Whether auto-negotiation is enabled.
OBJECT-TYPE    
  EnabledStatus  

portSpeedDpxStatus 7.1.259.6.10.94.1.2.1.1.8
The operating speed and duplex mode of the switched port or trunk. If the entry represents a trunk, the speed is that of its individual members unless the member ports have been inconsistently configured in which case the value is error(1).
OBJECT-TYPE    
  INTEGER error(1), halfDuplex10(2), fullDuplex10(3), halfDuplex100(4), fullDuplex100(5), halfDuplex1000(6), fullDuplex1000(7), halfDuplex10g(8), fullDuplex10g(9)  

portFlowCtrlStatus 7.1.259.6.10.94.1.2.1.1.9
(2) BackPressure flow control mechanism is used. (3) IEEE 802.3 flow control mechanism is used. (4) Flow control mechanism is disabled. If the entry represents a trunk and the member ports have been inconsistently configured then this value is error(1).
OBJECT-TYPE    
  INTEGER error(1), backPressure(2), dot3xFlowControl(3), none(4)  

portTrunkIndex 7.1.259.6.10.94.1.2.1.1.10
The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to a trunk in the trunkIndex, defined by the corresponding trunkPorts.
OBJECT-TYPE    
  Integer32  

portComboForcedMode 7.1.259.6.10.94.1.2.1.1.12
This determines the running mode of a combo port. For a non-combo port, this variable has a value of none(1), and setting this variable to none(1) has no effect. For a combo port, this has its own valid values not equal to none(1), and setting this variable to none(1) is not allowed. copperForced(2) is set if user want to force this combo port running in copper mode. copperPreferredAuto(3) is obsoleted, and user shall not set this state. sfpForced(4) is set if user want to force this combo port running in fiber mode. sfpPreferredAuto(5) is set if user want to change copper or fiber mode automatically by SFP transceiver present state. If SFP transceiver is present, this combo port will run in fiber mode, and if SFP transceiver is not present, this combo port will run in copper mode.
OBJECT-TYPE    
  INTEGER none(1), copperForced(2), copperPreferredAuto(3), sfpForced(4), sfpPreferredAuto(5)  

portMasterSlaveModeCfg 7.1.259.6.10.94.1.2.1.1.15
Configures the PHY mode when auto negotiation is disabled and speed-duplex is 1000full for giga copper port.
OBJECT-TYPE    
  INTEGER master(1), slave(2), auto(3), autoPreferMaster(4), autoPreferSlave(5)  

cableDiagMgt 7.1.259.6.10.94.1.2.3
OBJECT IDENTIFIER    

cableDiagCtlAction 7.1.259.6.10.94.1.2.3.1
To execute cable diagnostics on a port, assign cableDiagCtlAction to the value of ifIndex defined by the ifIndex in the IF-MIB. When read, this object always returns 0.
OBJECT-TYPE    
  Integer32  

cableDiagResultTable 7.1.259.6.10.94.1.2.3.2
Table for cable diagnostics result.
OBJECT-TYPE    
  SEQUENCE OF  
    CableDiagResultEntry

cableDiagResultEntry 7.1.259.6.10.94.1.2.3.2.1
Entry for cable diagnostics result.
OBJECT-TYPE    
  CableDiagResultEntry  

cableDiagResultIfIndex 7.1.259.6.10.94.1.2.3.2.1.1
This is defined as the ifIndex.
OBJECT-TYPE    
  Integer32  

cableDiagResultStatusPairA 7.1.259.6.10.94.1.2.3.2.1.2
The result of cable diagnostics. If there is no fault on the cable, the value is ok(2). Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Value short(4) means conductors are short-circuited together on the pair. Value openShort(5) means the pair has open and short issues. Value crosstalk(6) means the pair is incorrectly connected at one end. Value unknown(7) means pair has an error matching none of the above. Value impedanceMismatch(8) means different quality cables connected together. Value fail(9) means test failed. Value notSupport(10) means cable diagnostics is not supported.
OBJECT-TYPE    
  INTEGER notTestedYet(1), ok(2), open(3), short(4), openShort(5), crosstalk(6), unknown(7), impedanceMismatch(8), fail(9), notSupport(10)  

cableDiagResultStatusPairB 7.1.259.6.10.94.1.2.3.2.1.3
The result of cable diagnostics. If there is no fault on the cable, the value is ok(2). Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Value short(4) means conductors are short-circuited together on the pair. Value openShort(5) means the pair has open and short issues. Value crosstalk(6) means the pair is incorrectly connected at one end. Value unknown(7) means pair has an error matching none of the above. Value impedanceMismatch(8) means different quality cables connected together. Value fail(9) means test failed. Value notSupport(10) means cable diagnostics is not supported.
OBJECT-TYPE    
  INTEGER notTestedYet(1), ok(2), open(3), short(4), openShort(5), crosstalk(6), unknown(7), impedanceMismatch(8), fail(9), notSupport(10)  

cableDiagResultDistancePairA 7.1.259.6.10.94.1.2.3.2.1.6
Displays the fault distance of pair A of the cable in meters.
OBJECT-TYPE    
  Integer32  

cableDiagResultDistancePairB 7.1.259.6.10.94.1.2.3.2.1.7
Displays the fault distance of pair B of the cable in meters.
OBJECT-TYPE    
  Integer32  

cableDiagResultTime 7.1.259.6.10.94.1.2.3.2.1.11
Displays the last time of cable diagnostics. For example, 'Jan 1 02:03:04 2002'.
OBJECT-TYPE    
  DisplayString Size(0..20)  

portUtilTable 7.1.259.6.10.94.1.2.6
Dispalys port utilization during recent 300 seconds.
OBJECT-TYPE    
  SEQUENCE OF  
    PortUtilEntry

portUtilEntry 7.1.259.6.10.94.1.2.6.1
Dispalys port utilization during recent 300 seconds.
OBJECT-TYPE    
  PortUtilEntry  

portUtilIfIndex 7.1.259.6.10.94.1.2.6.1.1
The port and trunk interface of the portUtilTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Integer32  

portInOctetRate 7.1.259.6.10.94.1.2.6.1.2
The input octet rate (kbits/sec) of the port.
OBJECT-TYPE    
  Counter64  

portInPacketRate 7.1.259.6.10.94.1.2.6.1.3
The input packet rate (pkts/sec) of the port.
OBJECT-TYPE    
  Counter64  

portInUtil 7.1.259.6.10.94.1.2.6.1.4
The input utilization of the port, in one per hundred.
OBJECT-TYPE    
  Integer32  

portOutOctetRate 7.1.259.6.10.94.1.2.6.1.5
The output octet rate (kbits/sec) of the port.
OBJECT-TYPE    
  Counter64  

portOutPacketRate 7.1.259.6.10.94.1.2.6.1.6
The output packet rate (pkts/sec) of the port.
OBJECT-TYPE    
  Counter64  

portOutUtil 7.1.259.6.10.94.1.2.6.1.7
The output utilization of the port, in one per hundred.
OBJECT-TYPE    
  Integer32  

trunkMaxId 7.1.259.6.10.94.1.3.1
The maximum number for a trunk identifier.
OBJECT-TYPE    
  Integer32  

trunkValidNumber 7.1.259.6.10.94.1.3.2
The number of valid trunks.
OBJECT-TYPE    
  Integer32  

trunkTable 7.1.259.6.10.94.1.3.3
Table describing the configuration and status of each trunk.
OBJECT-TYPE    
  SEQUENCE OF  
    TrunkEntry

trunkEntry 7.1.259.6.10.94.1.3.3.1
An entry describing the configuration and status of a particular trunk.
OBJECT-TYPE    
  TrunkEntry  

trunkIndex 7.1.259.6.10.94.1.3.3.1.1
Identifies the trunk within the switch that is described by the table entry.
OBJECT-TYPE    
  Integer32  

trunkPorts 7.1.259.6.10.94.1.3.3.1.2
The complete set of ports currently associated with this trunk.
OBJECT-TYPE    
  PortList  

trunkCreation 7.1.259.6.10.94.1.3.3.1.3
A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk.
OBJECT-TYPE    
  INTEGER static(1), lacp(2)  

trunkStatus 7.1.259.6.10.94.1.3.3.1.4
Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. A trunk created by LACP cannot be manually destroyed or (re)configured.
OBJECT-TYPE    
  ValidStatus  

lacpPortTable 7.1.259.6.10.94.1.4.1
Table for LACP port configuration.
OBJECT-TYPE    
  SEQUENCE OF  
    LacpPortEntry

lacpPortEntry 7.1.259.6.10.94.1.4.1.1
Entry for LACP port configuration. While an entry may exist for a particular port, the port may not support LACP and an attempt to enable LACP may result in failure.
OBJECT-TYPE    
  LacpPortEntry  

lacpPortIndex 7.1.259.6.10.94.1.4.1.1.1
The port interface of the lacpPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Integer32  

lacpPortStatus 7.1.259.6.10.94.1.4.1.1.2
Whether 802.3ad LACP is enabled.
OBJECT-TYPE    
  EnabledStatus  

staSystemStatus 7.1.259.6.10.94.1.5.1
Global spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled.
OBJECT-TYPE    
  EnabledStatus  

staPortTable 7.1.259.6.10.94.1.5.2
The table manages port settings for Spanning Tree Protocol 802.1d, 802.1w or 802.1s depending on the value specified by staProtocolType.
OBJECT-TYPE    
  SEQUENCE OF  
    StaPortEntry

staPortEntry 7.1.259.6.10.94.1.5.2.1
The conceptual entry of staPortTable.
OBJECT-TYPE    
  StaPortEntry  

staPortFastForward 7.1.259.6.10.94.1.5.2.1.2
Whether fast forwarding is enabled.
OBJECT-TYPE    
  EnabledStatus  

staPortProtocolMigration 7.1.259.6.10.94.1.5.2.1.3
When operating in RSTP (version 2) mode, writing true(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns false(2) when read.
OBJECT-TYPE    
  TruthValue  

staPortOperEdgePort 7.1.259.6.10.94.1.5.2.1.5
The operational value of the edge port parameter. The object is initialized to the value of staPortAdminEdgePort and is set false when a BPDU is received.
OBJECT-TYPE    
  TruthValue  

staPortAdminPointToPoint 7.1.259.6.10.94.1.5.2.1.6
The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.
OBJECT-TYPE    
  INTEGER forceTrue(0), forceFalse(1), auto(2)  

staPortOperPointToPoint 7.1.259.6.10.94.1.5.2.1.7
The operational point-to-point status of the LAN segment attached to this port. This indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the staPortAdminPointToPoint object.
OBJECT-TYPE    
  TruthValue  

staPortSystemStatus 7.1.259.6.10.94.1.5.2.1.9
Per-port spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled.
OBJECT-TYPE    
  EnabledStatus  

staPortLongAdminPathCost 7.1.259.6.10.94.1.5.2.1.10
The admin value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This object is used to configure the spanning tree port path cost in the 32-bit value range when the staPathCostMethod is long(2). If the staPathCostMethod is short(1), this mib object is not instantiated. Setting this to 0 means that the path cost is automatically determined. In this case, read staPortLongOperPathCost to get the oper value.
OBJECT-TYPE    
  Integer32 0..200000000  

staPortLongOperPathCost 7.1.259.6.10.94.1.5.2.1.11
The oper value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This object is used to configure the spanning tree port path cost in the 32-bit value range when the staPathCostMethod is long(2). If the staPathCostMethod is short(1), this mib object is not instantiated.
OBJECT-TYPE    
  Integer32 1..200000000  

staPortRootGuardAdminStatus 7.1.259.6.10.94.1.5.2.1.13
Specifies the desired status of the root guard. This variable configures the root guard feature to enforce the root bridge placement in the network.
OBJECT-TYPE    
  EnabledStatus  

staPortRootGuardOperStatus 7.1.259.6.10.94.1.5.2.1.14
The current operational status of the root guard which provides a way to enforce the root bridge placement in the network.
OBJECT-TYPE    
  EnabledStatus  

staPortBpduGuard 7.1.259.6.10.94.1.5.2.1.15
A value of enabled(1) indicates that BPDU port guard feature is enabled for each port. A value of disabled(2) indicates that the feature is disabled.
OBJECT-TYPE    
  EnabledStatus  

staPortAdminEdgePortWithAuto 7.1.259.6.10.94.1.5.2.1.17
The administrative value of the edge port parameter. A value of enable(1) indicates that this port should be assumed as an edge-port, a value of disable(2) indicates that this port should be assumed as a non-edge-port and a value of auot (3) indicates this port in RSPT or MSTP mode should be assumed as an edge-port after migration or max age expire without receiving any BPDU and sending BPDU with proposal flag on.
OBJECT-TYPE    
  INTEGER true(1), false(2), auto(3)  

staPortBpduFilter 7.1.259.6.10.94.1.5.2.1.18
The administrative value of the BPDU filter parameter. A value of enabled(1) indicates that this port will avoid transmitting BPDUs on edge-port and the value of disabled(2) indicates that this port will not avoid transmitting BPDUs on edge-port.
OBJECT-TYPE    
  EnabledStatus  

staPortBpduGuardAutoRecovery 7.1.259.6.10.94.1.5.2.1.19
A value of enabled(1) indicates that BPDU port guard auto recovery mechanism is enabled for this port. A value of disabled(2) indicates that the mechanism is disabled.
OBJECT-TYPE    
  EnabledStatus  

staPortBpduGuardAutoRecoveryInterval 7.1.259.6.10.94.1.5.2.1.20
The interval in seconds used by BPDU guard auto recovery mechanism.
OBJECT-TYPE    
  Unsigned32 30..86400  

staProtocolType 7.1.259.6.10.94.1.5.3
The version of Spanning Tree Protocol the bridge is currently running. The value 'stp(1)' indicates the Spanning Tree Protocol is as specified in IEEE 802.1D,'rstp(2)' indicates that the Rapid Spanning Tree Protocol is as specified in IEEE 802.1w, and the value 'mstp(3)' indicates that the Multiple Spanning Tree Protocol is as specified in IEEE 802.1s. New values may be defined in the future as new or updated versions of the protocol become available.
OBJECT-TYPE    
  INTEGER stp(1), rstp(2), mstp(3)  

staTxHoldCount 7.1.259.6.10.94.1.5.4
The value used by the Port Transmit state machine to limit the maximum transmission rate.
OBJECT-TYPE    
  Integer32 1..10  

staPathCostMethod 7.1.259.6.10.94.1.5.5
Indicates the type of spanning tree path cost mode configured on the switch. This mode applies to all instances of the spanning tree protocol running on the switch. When the value of this MIB object is changed, the path cost of all ports will be reassigned to the default path cost values based on the new spanning tree path cost mode and the ports' speed. When the value of this MIB object is set to long(2), the staPortLongPathCost MIB object must be used to retrieve/configure the spanning tree port path cost as a 32-bit value. The set operation on dot1dStpPortPathCost in BRIDGE-MIB will be rejected. While retrieving the value of dot1dStpPortPathCost, the maximum value of 65535 will be returned if the value of staPortLongPathCost for the same instance exceeds 65535. When the value of this MIB object is set to short(1), the dot1dStpPortPathCost in BRIDGE-MIB must be used.
OBJECT-TYPE    
  StaPathCostMode  

xstMgt 7.1.259.6.10.94.1.5.6
OBJECT IDENTIFIER    

mstName 7.1.259.6.10.94.1.5.6.1
The name of the Multiple Spanning Tree region.
OBJECT-TYPE    
  DisplayString Size(0..32)  

mstRevision 7.1.259.6.10.94.1.5.6.2
The Revision number of the Multiple Spanning Tree region.
OBJECT-TYPE    
  Integer32  

mstMaxHops 7.1.259.6.10.94.1.5.6.3
The max hop number counts of the Multiple Spanning Tree region.
OBJECT-TYPE    
  Integer32 1..40  

xstInstanceCfgTable 7.1.259.6.10.94.1.5.6.4
This table is used to configure the property of a specific instance in Multiple Spanning Tree or Rapid Spanning Tree. If Rapid Spanning Tree protocol is in use, the mstInstanceEditIndex is always 0.
OBJECT-TYPE    
  SEQUENCE OF  
    XstInstanceCfgEntry

xstInstanceCfgEntry 7.1.259.6.10.94.1.5.6.4.1
A conceptual row containing the property of the RST or MST instance.
OBJECT-TYPE    
  XstInstanceCfgEntry  

xstInstanceCfgIndex 7.1.259.6.10.94.1.5.6.4.1.1
An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.
OBJECT-TYPE    
  Integer32 0..4094  

xstInstanceCfgPriority 7.1.259.6.10.94.1.5.6.4.1.2
The priority of a specific spanning tree instance. The value assigned should be in the range 0-61440 in steps of 4096.
OBJECT-TYPE    
  Integer32 0..61440  

xstInstanceCfgTimeSinceTopologyChange 7.1.259.6.10.94.1.5.6.4.1.3
The time (in hundredths of a second) since the last topology change detected by the bridge entity in RST or MST.
OBJECT-TYPE    
  TimeTicks  

xstInstanceCfgTopChanges 7.1.259.6.10.94.1.5.6.4.1.4
The total number of topology changes detected by this bridge in RST or MST since the management entity was last reset or initialized.
OBJECT-TYPE    
  Integer32  

xstInstanceCfgDesignatedRoot 7.1.259.6.10.94.1.5.6.4.1.5
The bridge identifier of the root of the spanning tree as determined by the Multiple Spanning Tree Protocol. (802.1s) or Rapid Spanning Tree Protocol (802.1w) executed by this node. This value is used as the root identifier parameter in all configuration bridge PDUs originated by this node.
OBJECT-TYPE    
  BridgeId  

xstInstanceCfgRootCost 7.1.259.6.10.94.1.5.6.4.1.6
The cost of the path to the root as seen from this bridge of the RST or MST.
OBJECT-TYPE    
  Integer32  

xstInstanceCfgRootPort 7.1.259.6.10.94.1.5.6.4.1.7
The number of the port which offers the lowest cost path from this bridge to the root bridge of the RST or MST.
OBJECT-TYPE    
  Integer32  

xstInstanceCfgMaxAge 7.1.259.6.10.94.1.5.6.4.1.8
The maximum age of Multiple Spanning Tree Protocol (802.1s) or Rapid Spanning Tree Protocol (802.1w) information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
OBJECT-TYPE    
  Timeout  

xstInstanceCfgHelloTime 7.1.259.6.10.94.1.5.6.4.1.9
The amount of time between the transmission of configuration bridge PDUs by this node on any port when it is the root of the specific spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using in RST or MST.
OBJECT-TYPE    
  Timeout  

xstInstanceCfgHoldTime 7.1.259.6.10.94.1.5.6.4.1.10
This time value determines the interval length during which no more than two configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
OBJECT-TYPE    
  Timeout  

xstInstanceCfgForwardDelay 7.1.259.6.10.94.1.5.6.4.1.11
For RST or MST protocol, this time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the forwarding state. The value determines how long the port stays in each of the listening and learning states, which precede the forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the forwarding database. This value is the current value being used by the bridge. xstInstanceCfgBridgeForwardDelay defines the value that this bridge and all others would start using if/when this bridge were to become the root.
OBJECT-TYPE    
  Timeout  

xstInstanceCfgBridgeMaxAge 7.1.259.6.10.94.1.5.6.4.1.12
For RST or MST protocol, the time (in hundredths of second) that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of xstInstanceCfgBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second.
OBJECT-TYPE    
  Timeout  

xstInstanceCfgBridgeHelloTime 7.1.259.6.10.94.1.5.6.4.1.13
For RST or MST protocol,the time (in hundredths of a second) that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second.
OBJECT-TYPE    
  Timeout  

xstInstanceCfgBridgeForwardDelay 7.1.259.6.10.94.1.5.6.4.1.14
For RST or MST protocol, the time (in hundredths of a second) that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of xstInstanceCfgBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second.
OBJECT-TYPE    
  Timeout  

xstInstanceCfgTxHoldCount 7.1.259.6.10.94.1.5.6.4.1.15
For RST or MST protocol, the value used by the port transmit state machine to limit the maximum transmission rate.
OBJECT-TYPE    
  Integer32  

xstInstanceCfgPathCostMethod 7.1.259.6.10.94.1.5.6.4.1.16
For RST or MST protocol, this indicates the type of spanning tree path cost mode used by the switch. The mode applies to all instances of the Spanning Tree protocol running on the switch. When the value of this MIB object is changed, the path cost of all ports will be reassigned to the default path cost values based on the new spanning tree path cost mode and the ports' speed. When the value of this MIB object is set to long(2), the xstInstancePortPathCost MIB object must be used in order to retrieve/configure the spanning tree port path cost as a 32-bit value. The set operation on dot1dStpPortPathCost in BRIDGE-MIB will be rejected. While retrieving the value of dot1dStpPortPathCost, the maximum value of 65535 will be returned if the value of xstInstancePortPathCost for the same instance exceeds 65535. When the value of this MIB object is set to short(1), the dot1dStpPortPathCost in BRIDGE-MIB must be used.
OBJECT-TYPE    
  StaPathCostMode  

xstInstancePortTable 7.1.259.6.10.94.1.5.6.5
The extension table for dot1dStpPortEntry to provide additional Spanning Tree information and configuration.
OBJECT-TYPE    
  SEQUENCE OF  
    XstInstancePortEntry

xstInstancePortEntry 7.1.259.6.10.94.1.5.6.5.1
The conceptual row for xstInstancePortTable.
OBJECT-TYPE    
  XstInstancePortEntry  

xstInstancePortInstance 7.1.259.6.10.94.1.5.6.5.1.1
The instance of the MSTP.
OBJECT-TYPE    
  Integer32  

xstInstancePortPort 7.1.259.6.10.94.1.5.6.5.1.2
The port and the trunk (excluding trunk member ports) interface of the mstInstancePortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1dStpPort in the BRIDGE-MIB.
OBJECT-TYPE    
  Integer32  

xstInstancePortPriority 7.1.259.6.10.94.1.5.6.5.1.3
Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest priority (i.e., lowest value) will be configured as an active link in the Spanning Tree. This makes a port with higher priority less likely to be blocked if the Spanning Tree Algorithm is detecting network loops. Where more than one port is assigned the highest priority, the port with lowest numeric identifier will be enabled.
OBJECT-TYPE    
  Integer32 0..240  

xstInstancePortState 7.1.259.6.10.94.1.5.6.5.1.4
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame: discarding(1): Port receives configuration messages, but does not forward packets. learning(2): Port has transmitted configuration messages for an interval set by the Forward Delay parameter without receiving contradictory information. Port address table is cleared, and the port begins learning addresses. forwarding(3): Port forwards packets, and continues learning addresses. For ports which are disabled (see xstInstancePortEnable), this object will have a value of discarding(1).
OBJECT-TYPE    
  INTEGER discarding(1), learning(2), forwarding(3)  

xstInstancePortEnable 7.1.259.6.10.94.1.5.6.5.1.5
The enabled/disabled status of the port.
OBJECT-TYPE    
  EnabledStatus  

xstInstancePortPathCost 7.1.259.6.10.94.1.5.6.5.1.6
The pathcost of the RST or MST in the range 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. (Path cost takes precedence over port priority).
OBJECT-TYPE    
  Integer32 1..200000000  

xstInstancePortDesignatedRoot 7.1.259.6.10.94.1.5.6.5.1.7
The unique bridge identifier of the bridge recorded as the root in the configuration BPDUs transmitted by the designated bridge for the segment to which the port is attached.
OBJECT-TYPE    
  BridgeId  

xstInstancePortDesignatedCost 7.1.259.6.10.94.1.5.6.5.1.8
The path cost of the designated port of the segment connected to this port. This value is compared to the root path cost field in received bridge PDUs.
OBJECT-TYPE    
  Integer32  

xstInstancePortDesignatedBridge 7.1.259.6.10.94.1.5.6.5.1.9
The bridge identifier of the bridge which this port considers to be the designated bridge for this port's segment.
OBJECT-TYPE    
  BridgeId  

xstInstancePortDesignatedPort 7.1.259.6.10.94.1.5.6.5.1.10
The port identifier of the port on the designated bridge for this port's segment.
OBJECT-TYPE    
  OCTET STRING Size(2)  

xstInstancePortForwardTransitions 7.1.259.6.10.94.1.5.6.5.1.11
The number of times this port has transitioned from the learning state to the forwarding state.
OBJECT-TYPE    
  Counter32  

xstInstancePortPortRole 7.1.259.6.10.94.1.5.6.5.1.12
The role of the port in the RST or MST protocol: (1) The port has no role within the spanning tree (2) The port is part of the active topology connecting the bridge to the root bridge (i.e., root port) (3) The port is connecting a LAN through the bridge to the root bridge (i.e., designated port) (4) The port may provide connectivity if other bridges, bridge ports, or LANs fail or are removed. (5) The port provides backup if other bridges, bridge ports, or LANs fail or are removed. (6) For MST protocol only, indicates whether this instance is in a master role.
OBJECT-TYPE    
  INTEGER disabled(1), root(2), designated(3), alternate(4), backup(5), master(6)  

xstInstancePortAdminPathCost 7.1.259.6.10.94.1.5.6.5.1.13
The admin value of the RST pathcost or MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. (Path cost takes precedence over port priority).
OBJECT-TYPE    
  Integer32 1..200000000  

xstInstancePortOperPathCost 7.1.259.6.10.94.1.5.6.5.1.14
The oper value of the RST pathcost or MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. (Path cost takes precedence over port priority).
OBJECT-TYPE    
  Integer32 1..200000000  

mstInstanceEditTable 7.1.259.6.10.94.1.5.6.6
The Multiple Spanning Tree region instance vlan configuration table. Please read the actual instance vlan mapped in the mstInstanceOperTable.
OBJECT-TYPE    
  SEQUENCE OF  
    MstInstanceEditEntry

mstInstanceEditEntry 7.1.259.6.10.94.1.5.6.6.1
A conceptual row containing the status of the MSTP instance.
OBJECT-TYPE    
  MstInstanceEditEntry  

mstInstanceEditIndex 7.1.259.6.10.94.1.5.6.6.1.1
An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.
OBJECT-TYPE    
  Integer32 0..4094  

mstInstanceEditVlansMap 7.1.259.6.10.94.1.5.6.6.1.2
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceEditVlansMap2k 7.1.259.6.10.94.1.5.6.6.1.3
A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceEditVlansMap3k 7.1.259.6.10.94.1.5.6.6.1.4
A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceEditVlansMap4k 7.1.259.6.10.94.1.5.6.6.1.5
A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceEditRemainingHops 7.1.259.6.10.94.1.5.6.6.1.6
The remaining hop count for this MST instance.
OBJECT-TYPE    
  Integer32  

mstInstanceOperTable 7.1.259.6.10.94.1.5.6.7
The Multiple Spanning Tree region instance vlan mapped table.
OBJECT-TYPE    
  SEQUENCE OF  
    MstInstanceOperEntry

mstInstanceOperEntry 7.1.259.6.10.94.1.5.6.7.1
A conceptual row containing the status of the MSTP instance.
OBJECT-TYPE    
  MstInstanceOperEntry  

mstInstanceOperIndex 7.1.259.6.10.94.1.5.6.7.1.1
An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.
OBJECT-TYPE    
  Integer32 0..4094  

mstInstanceOperVlansMap 7.1.259.6.10.94.1.5.6.7.1.2
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceOperVlansMap2k 7.1.259.6.10.94.1.5.6.7.1.3
A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceOperVlansMap3k 7.1.259.6.10.94.1.5.6.7.1.4
A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceOperVlansMap4k 7.1.259.6.10.94.1.5.6.7.1.5
A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

staLoopbackDetectionPortTable 7.1.259.6.10.94.1.5.7
A table provides the mechanism to configure the spanning tree loopback detection of each port or trunk
OBJECT-TYPE    
  SEQUENCE OF  
    StaLoopbackDetectionPortEntry

staLoopbackDetectionPortEntry 7.1.259.6.10.94.1.5.7.1
A conceptual row of staLoopbackDetectionPortTable.
OBJECT-TYPE    
  StaLoopbackDetectionPortEntry  

staLoopbackDetectionPortIfIndex 7.1.259.6.10.94.1.5.7.1.1
The port and the trunk interfaces of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  InterfaceIndex  

staLoopbackDetectionPortStatus 7.1.259.6.10.94.1.5.7.1.2
Status of the port on whether spanning tree loopback detection is enabled.
OBJECT-TYPE    
  EnabledStatus  

staLoopbackDetectionPortTrapStatus 7.1.259.6.10.94.1.5.7.1.3
The parameter indicates whether the trap has to be sent when the loopback BPDUs have been detected.
OBJECT-TYPE    
  EnabledStatus  

staLoopbackDetectionPortReleaseMode 7.1.259.6.10.94.1.5.7.1.4
Setting it to auto(1) indicates that this port can be released from discarding state automatically after loopback has occurred. Setting it to manual(2) indicates that this port can be released from discarding state manually after loopback has occurred.
OBJECT-TYPE    
  INTEGER auto(1), manual(2)  

staLoopbackDetectionPortRelease 7.1.259.6.10.94.1.5.7.1.5
Set this to release(2) to release the port from discarding state. noRelease(1) will always be obtained when reading this variable.
OBJECT-TYPE    
  INTEGER noRelease(1), release(2)  

restartOpCodeFile 7.1.259.6.10.94.1.7.1
Name of op-code file for start-up.
OBJECT-TYPE    
  DisplayString Size(0..127)  

restartConfigFile 7.1.259.6.10.94.1.7.2
Name of configuration file for start-up.
OBJECT-TYPE    
  DisplayString Size(0..127)  

restartControl 7.1.259.6.10.94.1.7.3
Setting this object to warmBoot(2) causes the device to reinitialize itself such that neither the agent configuration nor the protocol entity implementation is altered. Setting this object to coldBoot(3) causes the device to reinitialize itself such that the agent's configuration or the protocol entity implementation may be altered. When the device is running normally, this variable has a value of running(1).
OBJECT-TYPE    
  INTEGER running(1), warmBoot(2), coldBoot(3)  

mirrorTable 7.1.259.6.10.94.1.8.1
Table for port mirroring, enabling a port to be mirrored to/from another port. Not all ports can be mirrored and limitations may apply as to which ports can be used as either source or destination ports.
OBJECT-TYPE    
  SEQUENCE OF  
    MirrorEntry

mirrorEntry 7.1.259.6.10.94.1.8.1.1
The conceptual row of mirrorTable.
OBJECT-TYPE    
  MirrorEntry  

mirrorDestinationPort 7.1.259.6.10.94.1.8.1.1.1
The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Integer32  

mirrorSourcePort 7.1.259.6.10.94.1.8.1.1.2
The source port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Integer32  

mirrorType 7.1.259.6.10.94.1.8.1.1.3
If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), both receive and transmit packets will be mirrored.
OBJECT-TYPE    
  INTEGER rx(1), tx(2), both(3)  

mirrorStatus 7.1.259.6.10.94.1.8.1.1.4
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
OBJECT-TYPE    
  ValidStatus  

vlanMirrorTable 7.1.259.6.10.94.1.8.2
Table for VLAN mirroring, enabling a VLAN to be mirrored to a port.
OBJECT-TYPE    
  SEQUENCE OF  
    VlanMirrorEntry

vlanMirrorEntry 7.1.259.6.10.94.1.8.2.1
The conceptual row of vlanMirrorTable.
OBJECT-TYPE    
  VlanMirrorEntry  

vlanMirrorDestinationPort 7.1.259.6.10.94.1.8.2.1.1
The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Integer32  

vlanMirrorSourceVlan 7.1.259.6.10.94.1.8.2.1.2
The source VLAN for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB.
OBJECT-TYPE    
  Integer32  

vlanMirrorStatus 7.1.259.6.10.94.1.8.2.1.4
Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.
OBJECT-TYPE    
  ValidStatus  

igmpSnoopStatus 7.1.259.6.10.94.1.9.1
Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for IGMP ports.
OBJECT-TYPE    
  EnabledStatus  

igmpSnoopQuerier 7.1.259.6.10.94.1.9.2
Enables (disables) whether the switch acts as an IGMP querier.
OBJECT-TYPE    
  EnabledStatus  

igmpSnoopQueryCount 7.1.259.6.10.94.1.9.3
The query count from a querier, during which a response is expected from an endstation. If a querier has sent a number of counts defined by igmpSnoopQueryCount, but an endstation has not responded, a countdown timer is started using the time defined by igmpSnoopQueryMaxResponseTime. If the countdown finishes, and the endstation still has not responded, then that endstation is deemed to have left the multicast group.
OBJECT-TYPE    
  Integer32 2..10  

igmpSnoopQueryInterval 7.1.259.6.10.94.1.9.4
The interval (in seconds) between IGMP host-query messages sent by the switch.
OBJECT-TYPE    
  Integer32 60..125  

igmpSnoopQueryMaxResponseTime 7.1.259.6.10.94.1.9.5
The time after a query, during which a response is expected from an endstation. If a querier has sent a number of queries defined by igmpSnoopQueryCount, but an endstation has not responded, a countdown timer is started using an initial value set by igmpSnoopQueryMaxResponseTime. If the countdown finishes, and the endstation still has not responded, then that the endstation is deemed to have left the multicast group.
OBJECT-TYPE    
  Integer32 5..25  

igmpSnoopRouterPortExpireTime 7.1.259.6.10.94.1.9.6
Sets the time (in seconds) the switch waits after the previous querier has stopped querying before the router port (which received query packets from previous querier) expires.
OBJECT-TYPE    
  Integer32 300..500  

igmpSnoopVersion 7.1.259.6.10.94.1.9.7
IGMP version snooped
OBJECT-TYPE    
  Integer32 1..3  

igmpSnoopRouterCurrentTable 7.1.259.6.10.94.1.9.8
Table for current router ports.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopRouterCurrentEntry

igmpSnoopRouterCurrentEntry 7.1.259.6.10.94.1.9.8.1
Entry for current router ports.
OBJECT-TYPE    
  IgmpSnoopRouterCurrentEntry  

igmpSnoopRouterCurrentVlanIndex 7.1.259.6.10.94.1.9.8.1.1
The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRouterStaticTable.
OBJECT-TYPE    
  Unsigned32  

igmpSnoopRouterCurrentPorts 7.1.259.6.10.94.1.9.8.1.2
The set of ports which are current router ports, including static router ports. Please refer to igmpSnoopRouterStaticTable.
OBJECT-TYPE    
  PortList  

igmpSnoopRouterCurrentStatus 7.1.259.6.10.94.1.9.8.1.3
The set of ports which are static router ports.
OBJECT-TYPE    
  PortList  

igmpSnoopRouterStaticTable 7.1.259.6.10.94.1.9.9
Table for static router ports.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopRouterStaticEntry

igmpSnoopRouterStaticEntry 7.1.259.6.10.94.1.9.9.1
Entry for static router ports.
OBJECT-TYPE    
  IgmpSnoopRouterStaticEntry  

igmpSnoopRouterStaticVlanIndex 7.1.259.6.10.94.1.9.9.1.1
The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRouterStaticTable.
OBJECT-TYPE    
  Unsigned32  

igmpSnoopRouterStaticPorts 7.1.259.6.10.94.1.9.9.1.2
The set of ports which are static router ports.
OBJECT-TYPE    
  PortList  

igmpSnoopRouterStaticStatus 7.1.259.6.10.94.1.9.9.1.3
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
OBJECT-TYPE    
  ValidStatus  

igmpSnoopMulticastCurrentTable 7.1.259.6.10.94.1.9.10
Table for current multicast addresses.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopMulticastCurrentEntry

igmpSnoopMulticastCurrentEntry 7.1.259.6.10.94.1.9.10.1
Entry for current multicast addresses.
OBJECT-TYPE    
  IgmpSnoopMulticastCurrentEntry  

igmpSnoopMulticastCurrentVlanIndex 7.1.259.6.10.94.1.9.10.1.1
The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMulticastStaticTable.
OBJECT-TYPE    
  Unsigned32  

igmpSnoopMulticastCurrentIpAddress 7.1.259.6.10.94.1.9.10.1.2
IP address of multicast group.
OBJECT-TYPE    
  IpAddress  

igmpSnoopMulticastCurrentPorts 7.1.259.6.10.94.1.9.10.1.3
The set of ports which are members of a multicast group, including static members. Please refer to igmpSnoopMulticastStaticTable.
OBJECT-TYPE    
  PortList  

igmpSnoopMulticastCurrentStatus 7.1.259.6.10.94.1.9.10.1.4
The set of ports which are static members.
OBJECT-TYPE    
  PortList  

igmpSnoopMulticastStaticTable 7.1.259.6.10.94.1.9.11
Table for static multicast addresses.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopMulticastStaticEntry

igmpSnoopMulticastStaticEntry 7.1.259.6.10.94.1.9.11.1
Entry for static multicast addresses.
OBJECT-TYPE    
  IgmpSnoopMulticastStaticEntry  

igmpSnoopMulticastStaticVlanIndex 7.1.259.6.10.94.1.9.11.1.1
The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMulticastStaticTable.
OBJECT-TYPE    
  Unsigned32  

igmpSnoopMulticastStaticIpAddress 7.1.259.6.10.94.1.9.11.1.2
IP address of multicast group.
OBJECT-TYPE    
  IpAddress  

igmpSnoopMulticastStaticPorts 7.1.259.6.10.94.1.9.11.1.3
The set of ports which are members.
OBJECT-TYPE    
  PortList  

igmpSnoopMulticastStaticStatus 7.1.259.6.10.94.1.9.11.1.4
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
OBJECT-TYPE    
  ValidStatus  

igmpSnoopCurrentVlanTable 7.1.259.6.10.94.1.9.14
Table for enabling or disabling IGMP snooping per VLAN.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopCurrentVlanEntry

igmpSnoopCurrentVlanEntry 7.1.259.6.10.94.1.9.14.1
Entry for enabling or disabling IGMP snooping.
OBJECT-TYPE    
  IgmpSnoopCurrentVlanEntry  

igmpSnoopCurrentVlanIndex 7.1.259.6.10.94.1.9.14.1.1
Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.
OBJECT-TYPE    
  Unsigned32  

igmpSnoopCurrentVlanImmediateLeave 7.1.259.6.10.94.1.9.14.1.3
The parameter to enable or disable the Immediate-Leave feature on this VLAN.
OBJECT-TYPE    
  EnabledStatus  

igmpSnoopLeaveProxy 7.1.259.6.10.94.1.9.15
This enables or disables Leave Proxy for IGMP Snooping.
OBJECT-TYPE    
  EnabledStatus  

igmpSnoopFilterStatus 7.1.259.6.10.94.1.9.17
Parameter to enable or disable IGMP filtering on the device.
OBJECT-TYPE    
  EnabledStatus  

igmpSnoopProfileTable 7.1.259.6.10.94.1.9.18
The table for configuring the IGMP snooping profile.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopProfileEntry

igmpSnoopProfileEntry 7.1.259.6.10.94.1.9.18.1
The entry for configuring the IGMP snooping profile.
OBJECT-TYPE    
  IgmpSnoopProfileEntry  

igmpSnoopProfileId 7.1.259.6.10.94.1.9.18.1.1
The ID of the IGMP snooping profile.
OBJECT-TYPE    
  Unsigned32  

igmpSnoopProfileAction 7.1.259.6.10.94.1.9.18.1.2
The access mode of the IGMP snooping profile.
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

igmpSnoopProfileStatus 7.1.259.6.10.94.1.9.18.1.3
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
OBJECT-TYPE    
  ValidStatus  

igmpSnoopProfileCtl 7.1.259.6.10.94.1.9.19
OBJECT IDENTIFIER    

igmpSnoopProfileCtlId 7.1.259.6.10.94.1.9.19.1
The ID of the IGMP snooping profile.
OBJECT-TYPE    
  Unsigned32  

igmpSnoopProfileCtlInetAddressType 7.1.259.6.10.94.1.9.19.2
The address type is associated with this agent. Only ipv4(1) type is supported.
OBJECT-TYPE    
  InetAddressType  

igmpSnoopProfileCtlStartInetAddress 7.1.259.6.10.94.1.9.19.3
The specified addresses in the start of the controlled IP multicast addresses.
OBJECT-TYPE    
  InetAddress  

igmpSnoopProfileCtlEndInetAddress 7.1.259.6.10.94.1.9.19.4
The specified addresses in the end of the controlled IP multicast addresses.
OBJECT-TYPE    
  InetAddress  

igmpSnoopProfileCtlAction 7.1.259.6.10.94.1.9.19.5
Setting it to create(2) creates the range of the controlled IP multicast addresses. Setting it to destroy(3) destroys the range of the controlled IP multicast addresses. When the action is completed, this object becomes noAction(1).
OBJECT-TYPE    
  INTEGER noAction(1), create(2), destroy(3)  

igmpSnoopProfileRangeTable 7.1.259.6.10.94.1.9.20
The table for configuring the range of the IGMP snooping profile.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopProfileRangeEntry

igmpSnoopProfileRangeEntry 7.1.259.6.10.94.1.9.20.1
The entry for configuring the range of the IGMP snooping profile.
OBJECT-TYPE    
  IgmpSnoopProfileRangeEntry  

igmpSnoopProfileRangeProfileId 7.1.259.6.10.94.1.9.20.1.1
This is defined as igmpSnoopProfileId.
OBJECT-TYPE    
  Unsigned32  

igmpSnoopProfileRangeInetAddressType 7.1.259.6.10.94.1.9.20.1.2
The address type is associated with this agent. Only ipv4(1) type is supported.
OBJECT-TYPE    
  InetAddressType  

igmpSnoopProfileRangeStartInetAddress 7.1.259.6.10.94.1.9.20.1.3
The specified addresses in the start of the controlled IP multicast addresses.
OBJECT-TYPE    
  InetAddress  

igmpSnoopProfileRangeEndInetAddress 7.1.259.6.10.94.1.9.20.1.4
The specified addresses in the end of the controlled IP multicast addresses.
OBJECT-TYPE    
  InetAddress  

igmpSnoopProfileRangeAction 7.1.259.6.10.94.1.9.20.1.5
The access mode of the IGMP snooping profile.
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

igmpSnoopFilterPortTable 7.1.259.6.10.94.1.9.21
Table for port configuration in IGMP filtering.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopFilterPortEntry

igmpSnoopFilterPortEntry 7.1.259.6.10.94.1.9.21.1
Entry for port configuration in IGMP filtering.
OBJECT-TYPE    
  IgmpSnoopFilterPortEntry  

igmpSnoopFilterPortIndex 7.1.259.6.10.94.1.9.21.1.1
The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Unsigned32  

igmpSnoopFilterPortProfileId 7.1.259.6.10.94.1.9.21.1.2
The igmpSnoopProfileEntry identified by a particular value of this index is the same interface identified by the same value of the igmpSnoopProfileId object. If there is no corresponding entry in the igmpSnoopProfileTable, then no association exists. In particular, if this value is zero, no associated profile will be generated, as zero is not a valid profile index.
OBJECT-TYPE    
  Integer32  

igmpSnoopThrottlePortTable 7.1.259.6.10.94.1.9.22
Table for port configuration in IGMP throttling.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopThrottlePortEntry

igmpSnoopThrottlePortEntry 7.1.259.6.10.94.1.9.22.1
Entry for port configuration in IGMP throttling.
OBJECT-TYPE    
  IgmpSnoopThrottlePortEntry  

igmpSnoopThrottlePortIndex 7.1.259.6.10.94.1.9.22.1.1
The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Unsigned32  

igmpSnoopThrottlePortRunningStatus 7.1.259.6.10.94.1.9.22.1.2
Describes the running status of the IGMP throttling to the switch. A value of true(1) indicates the IGMP throttling mechanism is active. A value of false(2) indicates the IGMP throttling mechanism is inactive.
OBJECT-TYPE    
  TruthValue  

igmpSnoopThrottlePortAction 7.1.259.6.10.94.1.9.22.1.3
The action mode of the IGMP throttling. A value of replace(1) means to replace a joined multicast group randomly when an interface receives an IGMP report and the number of current joined multicast groups is equal to the maximum number of IGMP groups that the interface can join. A value of deny(2) means to deny the IGMP report request when an interface receives an IGMP report and the number of current joined multicast groups is equal to the maximum number of IGMP groups that the interface can join.
OBJECT-TYPE    
  INTEGER replace(1), deny(2)  

igmpSnoopThrottlePortMaxGroups 7.1.259.6.10.94.1.9.22.1.4
The maximum number of IGMP groups that the interface can join.
OBJECT-TYPE    
  Integer32 0..256  

igmpSnoopThrottlePortCurrentGroups 7.1.259.6.10.94.1.9.22.1.5
The current number of IGMP groups that the interface has joined.
OBJECT-TYPE    
  Integer32  

igmpSnoopPortTable 7.1.259.6.10.94.1.9.27
Table of IGMP Snooping service per port.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopPortEntry

igmpSnoopPortEntry 7.1.259.6.10.94.1.9.27.1
Entry of IGMP Snooping service per port.
OBJECT-TYPE    
  IgmpSnoopPortEntry  

igmpSnoopPortIndex 7.1.259.6.10.94.1.9.27.1.1
The port and the trunk (excluding trunk members) interface of the igmpSnoopPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Unsigned32  

igmpSnoopQueryDrop 7.1.259.6.10.94.1.9.27.1.3
Parameter to enable or disable dropping IGMP Query packet.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

igmpSnoopForwardingPriority 7.1.259.6.10.94.1.9.29
Configure IGMP snooping multicast stream forwarding priority. If value is 65535, it means the priority is disabled
OBJECT-TYPE    
  Integer32 0..6 | 65535  

igmpSnoopPortVlanTable 7.1.259.6.10.94.1.9.32
Table of IGMP Snooping service per port per VLAN.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopPortVlanEntry

igmpSnoopPortVlanEntry 7.1.259.6.10.94.1.9.32.1
Entry of IGMP Snooping service per port.
OBJECT-TYPE    
  IgmpSnoopPortVlanEntry  

igmpSnoopPortVlanPortIndex 7.1.259.6.10.94.1.9.32.1.1
The port and the trunk (excluding trunk members) interface of the igmpSnoopPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Unsigned32  

igmpSnoopPortVlanVlanIndex 7.1.259.6.10.94.1.9.32.1.2
The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB.
OBJECT-TYPE    
  Unsigned32  

igmpSnoopPortVlanQueryDrop 7.1.259.6.10.94.1.9.32.1.3
Parameter to enable or disable dropping IGMP Query packet.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

netConfigTable 7.1.259.6.10.94.1.10.1
A table of netConfigEntry.
OBJECT-TYPE    
  SEQUENCE OF  
    NetConfigEntry

netConfigEntry 7.1.259.6.10.94.1.10.1.1
A set of configuration parameters for a particular network interface on this device. If the device has no network interface, this table is empty. The index is composed of the ifIndex assigned to the corresponding interface.
OBJECT-TYPE    
  NetConfigEntry  

netConfigIfIndex 7.1.259.6.10.94.1.10.1.1.1
The VLAN interface being used by this table entry. Only the VLAN interfaces which have an IP configured will appear in the table.
OBJECT-TYPE    
  Integer32  

netConfigIPAddress 7.1.259.6.10.94.1.10.1.1.2
The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask is 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
OBJECT-TYPE    
  IpAddress  

netConfigSubnetMask 7.1.259.6.10.94.1.10.1.1.3
The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
OBJECT-TYPE    
  IpAddress  

netConfigPrimaryInterface 7.1.259.6.10.94.1.10.1.1.4
Whether this is a primary interface.
OBJECT-TYPE    
  INTEGER primary(1), secondary(2)  

netConfigUnnumbered 7.1.259.6.10.94.1.10.1.1.5
Whether this is an unnumbered interface.
OBJECT-TYPE    
  INTEGER unnumbered(1), notUnnumbered(2)  

netConfigStatus 7.1.259.6.10.94.1.10.1.1.6
The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
OBJECT-TYPE    
  RowStatus  

netDefaultGateway 7.1.259.6.10.94.1.10.2
The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0.
OBJECT-TYPE    
  IpAddress  

ipHttpState 7.1.259.6.10.94.1.10.3
Whether HTTP is enabled.
OBJECT-TYPE    
  EnabledStatus  

ipHttpPort 7.1.259.6.10.94.1.10.4
The port number for HTTP.
OBJECT-TYPE    
  Integer32 1..65535  

ipDhcpRestart 7.1.259.6.10.94.1.10.5
When set to restart(1) the DHCP server will restart. When read, this value always returns noRestart(2).
OBJECT-TYPE    
  INTEGER restart(1), noRestart(2)  

ipHttpsState 7.1.259.6.10.94.1.10.6
Whether HTTPS is enabled.
OBJECT-TYPE    
  EnabledStatus  

ipHttpsPort 7.1.259.6.10.94.1.10.7
The port number for HTTPS.
OBJECT-TYPE    
  Integer32 1..65535  

dhcpMgt 7.1.259.6.10.94.1.10.11
OBJECT IDENTIFIER    

dhcpClient 7.1.259.6.10.94.1.10.11.1
OBJECT IDENTIFIER    

dhcpOption82 7.1.259.6.10.94.1.10.11.4
OBJECT IDENTIFIER    

dhcpcOptions 7.1.259.6.10.94.1.10.11.1.1
OBJECT IDENTIFIER    

dhcpcInterfaceTable 7.1.259.6.10.94.1.10.11.1.1.1
Table for DHCP client information listed by interface. Depending on the nature of the product, this table may have only one entry(e.g. for the management VLAN), or may have many entries(e.g. for all ports, or for all static VLANs).
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpcInterfaceEntry

dhcpcInterfaceEntry 7.1.259.6.10.94.1.10.11.1.1.1.1
Entry for DHCP client information listed by interface.
OBJECT-TYPE    
  DhcpcInterfaceEntry  

dhcpcIfIndex 7.1.259.6.10.94.1.10.11.1.1.1.1.1
This is defined by ifIndex in the IF-MIB.(static vlan if index)
OBJECT-TYPE    
  Integer32  

dhcpcIfClientIdMode 7.1.259.6.10.94.1.10.11.1.1.1.1.2
Whether the Client ID is in text mode or in Hex mode.
OBJECT-TYPE    
  INTEGER notSpecify(1), text(2), hex(3)  

dhcpcIfClientId 7.1.259.6.10.94.1.10.11.1.1.1.1.3
The value that the DHCP client sets in the client_id option of DHCPDISCOVER and DHCPREQUEST messages. This value may be used by DHCP servers to uniquely identify the client.
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

dhcpOption82Status 7.1.259.6.10.94.1.10.11.4.1
Set enabled(1) to enable DHCP Relay Option 82, set disabled(2) to disable it.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dhcpOption82Policy 7.1.259.6.10.94.1.10.11.4.2
Provide three policies to handle packet
OBJECT-TYPE    
  INTEGER drop(1), replace(2), keep(3)  

dhcpOption82RemoteIDMode 7.1.259.6.10.94.1.10.11.4.3
Provide five mode for insertion remote-id sub-option of option 82. If configured-string(5) has been set, dhcpOption82RemoteIDString will take effect.
OBJECT-TYPE    
  INTEGER mac-address-in-hex(1), mac-address-in-ascii(2), ip-address-in-hex(3), ip-address-in-ascii(4), configured-string(5)  

dhcpOption82RemoteIDString 7.1.259.6.10.94.1.10.11.4.4
Set string to remote-id sub-option of option 82. It only take effect when dhcpOption82RemoteIDMode is set to configured-string(5)
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

dhcpOption82EncodeFormat 7.1.259.6.10.94.1.10.11.4.5
Set encode format for CID and RID in option82. Set extra-subtype-included(1) will have extra subtype and length field in CID and RID. Set no-extra-subtype-included(2) will only have TLV format for CID and RID.
OBJECT-TYPE    
  INTEGER extra-subtype-included(1), no-extra-subtype-included(2)  

dhcpOption82RelayServerAddrTable 7.1.259.6.10.94.1.10.11.4.6
This table is to specify relay server IP address, the maximum number of server IP addresses user can specify is 5.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpOption82RelayServerAddrEntry

dhcpOption82RelayServerAddrEntry 7.1.259.6.10.94.1.10.11.4.6.1
A conceptual row of dhcpOption82RelayServerAddrTable.
OBJECT-TYPE    
  DhcpOption82RelayServerAddrEntry  

dhcpOption82RelayServerAddrIndex 7.1.259.6.10.94.1.10.11.4.6.1.1
The index of the relay server IP address.
OBJECT-TYPE    
  Integer32 1..5  

dhcpOption82RelayServerAddrServerIp 7.1.259.6.10.94.1.10.11.4.6.1.2
The IP address of the relay server.
OBJECT-TYPE    
  IpAddress  

arpCacheDeleteAll 7.1.259.6.10.94.1.10.17
To delete all dynamic entries in the ARP cache, write this variable to delete(1). Writing this variable to noDelete(2) has no effect on the device. When read, this variable always returns noDelete(2). This object is only for Layer 2 switch.
OBJECT-TYPE    
  INTEGER delete(1), noDelete(2)  

vlanTable 7.1.259.6.10.94.1.12.1
Table for VLAN configuration.
OBJECT-TYPE    
  SEQUENCE OF  
    VlanEntry

vlanEntry 7.1.259.6.10.94.1.12.1.1
Entry for VLAN configuration.
OBJECT-TYPE    
  VlanEntry  

vlanIndex 7.1.259.6.10.94.1.12.1.1.1
Based on dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.
OBJECT-TYPE    
  Unsigned32  

vlanAddressMethod 7.1.259.6.10.94.1.12.1.1.2
Method to get the IP address.
OBJECT-TYPE    
  INTEGER user(1), bootp(2), dhcp(3)  

vlanPortTable 7.1.259.6.10.94.1.12.2
Table for port configuration in VLAN.
OBJECT-TYPE    
  SEQUENCE OF  
    VlanPortEntry

vlanPortEntry 7.1.259.6.10.94.1.12.2.1
Entry for port configuration in VLAN.
OBJECT-TYPE    
  VlanPortEntry  

vlanPortIndex 7.1.259.6.10.94.1.12.2.1.1
The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qPvid in the Q-BRIDGE-MIB.
OBJECT-TYPE    
  Integer32  

vlanPortMode 7.1.259.6.10.94.1.12.2.1.2
This variable sets the 802.1Q VLAN mode. Setting it to hybrid(1) sets a hybrid link. Setting it to dot1qTrunk(2) sets a trunk link. Setting it to access(3) sets an access link.
OBJECT-TYPE    
  INTEGER hybrid(1), dot1qTrunk(2), access(3)  

vlanPortPrivateVlanType 7.1.259.6.10.94.1.12.2.1.3
The port type defined for private VLAN.
OBJECT-TYPE    
  INTEGER normal(1), isolated(2), community(3), promiscous(4)  

protocolVlanTable 7.1.259.6.10.94.1.12.5
The configuration table which contains the binding entry of the protocol-group and VLANs.
OBJECT-TYPE    
  SEQUENCE OF  
    ProtocolVlanEntry

protocolVlanEntry 7.1.259.6.10.94.1.12.5.1
The binding entry of the protocol-group and VLANs.
OBJECT-TYPE    
  ProtocolVlanEntry  

protocolVlanGroupId 7.1.259.6.10.94.1.12.5.1.1
The specified protocol group of a binding entry.
OBJECT-TYPE    
  Integer32  

protocolVlanGroupVid 7.1.259.6.10.94.1.12.5.1.2
The vlan index of the binding entry. The vid zero is used to delete the binding entry.
OBJECT-TYPE    
  Integer32  

vlanDot1qTunnelGlobalConfig 7.1.259.6.10.94.1.12.7
OBJECT IDENTIFIER    

vlanDot1qTunnelStatus 7.1.259.6.10.94.1.12.7.1
This parameter is used to globally enable/disable 802.1Q Tunneling on the device.
OBJECT-TYPE    
  EnabledStatus  

vlanDot1qTunnelPortTable 7.1.259.6.10.94.1.12.8
Table for port configuration in 802.1Q Tunneling.
OBJECT-TYPE    
  SEQUENCE OF  
    VlanDot1qTunnelPortEntry

vlanDot1qTunnelPortEntry 7.1.259.6.10.94.1.12.8.1
Entry for port configuration in 802.1Q Tunneling.
OBJECT-TYPE    
  VlanDot1qTunnelPortEntry  

vlanDot1qTunnelPortIndex 7.1.259.6.10.94.1.12.8.1.1
The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Integer32  

vlanDot1qTunnelPortMode 7.1.259.6.10.94.1.12.8.1.2
This variable sets the 802.1Q Tunneling mode. Setting it to none(1) indicates no mode in this port. Setting it to dot1qTunnel(2) sets as dot1q-tunnel mode port which link to customer. Setting it to dot1qTunnelUplink(3) sets as dot1q-tunnel mode port which link to service-provider. If vlanDot1qTunnelStatus is disabled, it means vlanDot1qTunnelPortMode is inactive.
OBJECT-TYPE    
  INTEGER none(1), dot1qTunnel(2), dot1qTunnelUplink(3)  

vlanDot1qTunnelPortEtherType 7.1.259.6.10.94.1.12.8.1.3
TPID for 802.1Q encapsulation. It's used to select a nonstandard (nondefault) 2-byte ethertype to identify 802.1Q tagged frames.
OBJECT-TYPE    
  Unsigned32 0800..ffff  

voiceVlanMgt 7.1.259.6.10.94.1.12.6
OBJECT IDENTIFIER    

voiceVlanOuiTable 7.1.259.6.10.94.1.12.6.1
A table containing the mac address which can be identified by voice vlan.
OBJECT-TYPE    
  SEQUENCE OF  
    VoiceVlanOuiEntry

voiceVlanOuiEntry 7.1.259.6.10.94.1.12.6.1.1
A table containing the mac address which can be identified by voice vlan.
OBJECT-TYPE    
  VoiceVlanOuiEntry  

voiceVlanOuiAddress 7.1.259.6.10.94.1.12.6.1.1.1
MAC address can be identified by voice vlan.
OBJECT-TYPE    
  MacAddress  

voiceVlanOuiMask 7.1.259.6.10.94.1.12.6.1.1.2
The mask of MAC address.
OBJECT-TYPE    
  MacAddress  

voiceVlanOuiDescription 7.1.259.6.10.94.1.12.6.1.1.3
The description of oui.
OBJECT-TYPE    
  DisplayString Size(0..30)  

voiceVlanOuiStatus 7.1.259.6.10.94.1.12.6.1.1.4
Current operation status of the row.
OBJECT-TYPE    
  ValidStatus  

voiceVlanEnabledId 7.1.259.6.10.94.1.12.6.2
Voice vlan enable status: enabled (2..4095), disabled (-1).
OBJECT-TYPE    
  INTEGER  

voiceVlanAgingTime 7.1.259.6.10.94.1.12.6.3
Voice vlan aging time, the unit of which is minute.
OBJECT-TYPE    
  INTEGER 5..43200  

voiceVlanPortTable 7.1.259.6.10.94.1.12.6.7
A list of voice vlan mode entries.
OBJECT-TYPE    
  SEQUENCE OF  
    VoiceVlanPortEntry

voiceVlanPortEntry 7.1.259.6.10.94.1.12.6.7.1
An entry containing voice vlan mode information, which is applicable to a voice vlan enabled interface.
OBJECT-TYPE    
  VoiceVlanPortEntry  

voiceVlanPortIfIndex 7.1.259.6.10.94.1.12.6.7.1.1
The index of interface on which voice vlan function is enabled.
OBJECT-TYPE    
  Integer32 1..2147483647  

voiceVlanPortMode 7.1.259.6.10.94.1.12.6.7.1.2
Voice vlan configuration mode status.
OBJECT-TYPE    
  INTEGER auto(1), manual(2), none(3)  

voiceVlanPortSecurity 7.1.259.6.10.94.1.12.6.7.1.3
If the security is enabled, the port is only allow voice traffuc for the voice vlan.
OBJECT-TYPE    
  EnabledStatus  

voiceVlanPortPriority 7.1.259.6.10.94.1.12.6.7.1.4
The priority of the voice vlan traffic in the port.
OBJECT-TYPE    
  INTEGER 0..6  

voiceVlanPortRuleOui 7.1.259.6.10.94.1.12.6.7.1.5
The address of voice device is learned from Oui table.
OBJECT-TYPE    
  EnabledStatus  

voiceVlanPortRuleLldp 7.1.259.6.10.94.1.12.6.7.1.6
The address of voice device is learned from LLDP discovery.
OBJECT-TYPE    
  EnabledStatus  

voiceVlanRemarkIpDscpStatus 7.1.259.6.10.94.1.12.6.8
Set enabled(1) to enable remarking of IP DSCP for voice traffic. Set disabled(2) to disable it.
OBJECT-TYPE    
  EnabledStatus  

voiceVlanIpDscp 7.1.259.6.10.94.1.12.6.9
New IP DSCP value for voice traffic.
OBJECT-TYPE    
  INTEGER  

macVlanTable 7.1.259.6.10.94.1.12.11
A table that contains the settings for MAC-based VLAN.
OBJECT-TYPE    
  SEQUENCE OF  
    MacVlanEntry

macVlanEntry 7.1.259.6.10.94.1.12.11.1
A conceptual row in the macVlanTable.
OBJECT-TYPE    
  MacVlanEntry  

macVlanMacAddress 7.1.259.6.10.94.1.12.11.1.1
The MAC address that may specify an entry in the table which contains MAC-based VLAN information.
OBJECT-TYPE    
  MacAddress  

macVlanId 7.1.259.6.10.94.1.12.11.1.2
Specifies the VLAN ID which the MAC address associates with.
OBJECT-TYPE    
  Integer32 1..4092  

macVlanStatus 7.1.259.6.10.94.1.12.11.1.4
Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.
OBJECT-TYPE    
  ValidStatus  

macVlanMacMask 7.1.259.6.10.94.1.12.11.1.5
The MAC address mask that may specify an entry in the table which contains MAC-based VLAN information.
OBJECT-TYPE    
  MacAddress  

macVlanClearAction 7.1.259.6.10.94.1.12.12
Action for clearing macVlanTable. When this object is set to clear(2), all entries in macVlanTable will be cleared. When this object is read, the value of this object is always noClear(1).
OBJECT-TYPE    
  INTEGER noClear(1), clear(2)  

subnetVlanTable 7.1.259.6.10.94.1.12.13
A table that contains the settings for IP subnet-based VLAN.
OBJECT-TYPE    
  SEQUENCE OF  
    SubnetVlanEntry

subnetVlanEntry 7.1.259.6.10.94.1.12.13.1
A conceptual row in the subnetVlanTable.
OBJECT-TYPE    
  SubnetVlanEntry  

subnetVlanIpAddress 7.1.259.6.10.94.1.12.13.1.1
The IPv4 address of a subnet. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the subnetVlanMask object is not equal to x.
OBJECT-TYPE    
  IpAddress  

subnetVlanMask 7.1.259.6.10.94.1.12.13.1.2
The netmask of a subnet. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the subnetVlanIpAddress object is not equal to subnetVlanIpAddress.
OBJECT-TYPE    
  IpAddress  

subnetVlanId 7.1.259.6.10.94.1.12.13.1.3
Specifies the VLAN ID which the subnet associates with.
OBJECT-TYPE    
  Integer32 1..4094  

subnetVlanPriority 7.1.259.6.10.94.1.12.13.1.4
Specifies the priority whcich the subnet associates with.
OBJECT-TYPE    
  Integer32 0..7  

subnetVlanStatus 7.1.259.6.10.94.1.12.13.1.5
Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.
OBJECT-TYPE    
  ValidStatus  

subnetVlanClearAction 7.1.259.6.10.94.1.12.14
Action for clearing subnetVlanTable. When this object is set to clear(2), all entries in subnetVlanTable will be cleared. When this object is read, the value of this object is always noClear(1).
OBJECT-TYPE    
  INTEGER noClear(1), clear(2)  

vlanL2ProtocolTunnelPortTable 7.1.259.6.10.94.1.12.16
Table for port configuration in Layer 2 Protocol Tunneling.
OBJECT-TYPE    
  SEQUENCE OF  
    VlanL2ProtocolTunnelPortEntry

vlanL2ProtocolTunnelPortEntry 7.1.259.6.10.94.1.12.16.1
Entry for port configuration in Layer 2 Protocol Tunneling.
OBJECT-TYPE    
  VlanL2ProtocolTunnelPortEntry  

vlanL2ptPortIndex 7.1.259.6.10.94.1.12.16.1.1
The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Integer32  

vlanL2ptPortSta 7.1.259.6.10.94.1.12.16.1.2
Set enabled(1) to enable Layer 2 protocol tunneling for spanning-tree protocol. Set disabled(2) to disable Layer 2 protocol tunneling for spanning-tree protocol.
OBJECT-TYPE    
  EnabledStatus  

vlanL2ptPortLldp 7.1.259.6.10.94.1.12.16.1.3
Set enabled(1) to enable Layer 2 protocol tunneling for LLDP. Set disabled(2) to disable Layer 2 protocol tunneling for LLDP.
OBJECT-TYPE    
  EnabledStatus  

vlanL2ptPortCdp 7.1.259.6.10.94.1.12.16.1.4
Set enabled(1) to enable Layer 2 protocol tunneling for Cisco Discovery Protocol. Set disabled(2) to disable Layer 2 protocol tunneling for Cisco Discovery Protocol.
OBJECT-TYPE    
  EnabledStatus  

vlanL2ptPortVtp 7.1.259.6.10.94.1.12.16.1.5
Set enabled(1) to enable Layer 2 protocol tunneling for Cisco VTP. Set disabled(2) to disable Layer 2 protocol tunneling for Cisco VTP.
OBJECT-TYPE    
  EnabledStatus  

vlanL2ptPortPvst 7.1.259.6.10.94.1.12.16.1.6
Set enabled(1) to enable Layer 2 protocol tunneling for Cisco PVST+. Set disabled(2) to disable Layer 2 protocol tunneling for Cisco PVST+.
OBJECT-TYPE    
  EnabledStatus  

vlanL2ProtocolTunnelGlobalConfig 7.1.259.6.10.94.1.12.19
OBJECT IDENTIFIER    

vlanL2ProtocolTunnelAddress 7.1.259.6.10.94.1.12.19.1
Destination MAC address for PDU tunneling.
OBJECT-TYPE    
  MacAddress  

prioIpPrecDscpStatus 7.1.259.6.10.94.1.13.1
Selects whether no frame priority mapping, IP ToS precedence mapping or DSCP mapping is performed.
OBJECT-TYPE    
  INTEGER disabled(1), precedence(2), dscp(3)  

prioIpDscpTable 7.1.259.6.10.94.1.13.4
Table for IP DSCP priority mapping.
OBJECT-TYPE    
  SEQUENCE OF  
    PrioIpDscpEntry

prioIpDscpEntry 7.1.259.6.10.94.1.13.4.1
Entry for IP DSCP priority mapping.
OBJECT-TYPE    
  PrioIpDscpEntry  

prioIpDscpPort 7.1.259.6.10.94.1.13.4.1.1
The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Integer32  

prioIpDscpValue 7.1.259.6.10.94.1.13.4.1.2
Value of IP DSCP as specified in the packet header.
OBJECT-TYPE    
  Integer32 0..63  

prioIpDscpCos 7.1.259.6.10.94.1.13.4.1.3
Class of Service as defined by dot1dTrafficClassPriority in the P-BRIDGE-MIB. The prioIpDscpValue value in the same table row will be mapped to this Class of Service (CoS). This CoS is then further mapped to the hardware queue according to dot1dTrafficClassTable.
OBJECT-TYPE    
  Integer32 0..7  

prioIpDscpRestoreDefault 7.1.259.6.10.94.1.13.5
Enables the IP DSCP settings of a port to be reset to their defaults. To reset the IP DSCP settings of a port, assign the value of the relevant ifIndex defined by the ifIndex in the IF-MIB. For example, assigning the value 1 will result in the IP DSCP settings of port 1 being restored to their default. 0 will always be obtained when reading this variable
OBJECT-TYPE    
  Integer32  

prioCopy 7.1.259.6.10.94.1.13.8
OBJECT IDENTIFIER    

prioCopyIpDscp 7.1.259.6.10.94.1.13.8.2
Action to copy IP DSCP settings from a source port to many destination ports. The first four octets represent an integer for the source port in high-to-low (big-endian) order. Starting from the 5th octet is the destination port list in a form described by PortList in the Q-BRIDGE-MIB. Writing this object will perform copy. Reading this object will always get a zero-length octet string.
OBJECT-TYPE    
  OCTET STRING  

prioWrrTable 7.1.259.6.10.94.1.13.9
Table for weighted round robin (WRR).
OBJECT-TYPE    
  SEQUENCE OF  
    PrioWrrEntry

prioWrrEntry 7.1.259.6.10.94.1.13.9.1
Entry for weighted round robin (WRR).
OBJECT-TYPE    
  PrioWrrEntry  

prioWrrTrafficClass 7.1.259.6.10.94.1.13.9.1.1
Traffic class for this entry, as defined in dot1dTrafficClass in the P-BRIDGE-MIB. The actual maximum depends on the hardware, and is equal to dot1dPortNumTrafficClasses-1.
OBJECT-TYPE    
  Integer32 0..7  

prioWrrWeight 7.1.259.6.10.94.1.13.9.1.2
Weight for this entry.
OBJECT-TYPE    
  Integer32 1..255  

prioQueueMode 7.1.259.6.10.94.1.13.10
The global status for the prioQueue. wrr(1),strict(2)
OBJECT-TYPE    
  INTEGER wrr(1), strict(2)  

trapDestTable 7.1.259.6.10.94.1.14.1
A list of trap destination entries.
OBJECT-TYPE    
  SEQUENCE OF  
    TrapDestEntry

trapDestEntry 7.1.259.6.10.94.1.14.1.1
A destination entry describes the destination IP address, the community string, and SNMP version to use when sending a trap.
OBJECT-TYPE    
  TrapDestEntry  

trapDestAddress 7.1.259.6.10.94.1.14.1.1.1
The address to send traps.
OBJECT-TYPE    
  IpAddress  

trapDestCommunity 7.1.259.6.10.94.1.14.1.1.2
A community to which this destination address belongs.
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

trapDestStatus 7.1.259.6.10.94.1.14.1.1.3
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
OBJECT-TYPE    
  ValidStatus  

trapDestVersion 7.1.259.6.10.94.1.14.1.1.4
Determines the version of the trap that is to be sent to the trap receiver. If the value is 1, then an SNMP version 1 trap is sent and if the value is 2, an SNMP version 2 trap is sent.
OBJECT-TYPE    
  INTEGER version1(1), version2(2)  

trapDestUdpPort 7.1.259.6.10.94.1.14.1.1.5
Determines the UDP port number that the trap will be sent to.
OBJECT-TYPE    
  Integer32 1..65535  

trapVar 7.1.259.6.10.94.1.14.2
OBJECT IDENTIFIER    

trapIpFilterRejectMode 7.1.259.6.10.94.1.14.2.6
This variable is for trap var binding, indicated the ipfilter reject mode. web(1), snmp(2), telnet(3).
OBJECT-TYPE    
  INTEGER web(1), snmp(2), telnet(3)  

trapIpFilterRejectIp 7.1.259.6.10.94.1.14.2.7
This variable is for trap var binding, indicating the IP address that rejected by the ipfilter.
OBJECT-TYPE    
  Integer32  

trapAutoUpgradeResult 7.1.259.6.10.94.1.14.2.18
The parameter indicates which result triggers the trap.
OBJECT-TYPE    
  INTEGER succeeded(1), failed(2)  

trapAutoUpgradeNewVer 7.1.259.6.10.94.1.14.2.19
The parameter indicates new version which was upgraded to. When trapAutoUpgradeResult was failed(2), it would be null string.
OBJECT-TYPE    
  DisplayString Size(0..20)  

trapDhcpClientPortIfIndex 7.1.259.6.10.94.1.14.2.20
ifIndex for the port connected to DHCP rouge server.
OBJECT-TYPE    
  INTEGER  

trapDhcpServerIpAddress 7.1.259.6.10.94.1.14.2.21
The IP address of the rouge server.
OBJECT-TYPE    
  DisplayString  

trapMacNotifyVid 7.1.259.6.10.94.1.14.2.24
This variable is for trap var binding, indicated the VLAN id of MAC operation.
OBJECT-TYPE    
  Unsigned32  

trapMacNotifyMac 7.1.259.6.10.94.1.14.2.25
This variable is for trap var binding, indicated the MAC address of MAC operation.
OBJECT-TYPE    
  MacAddress  

trapMacNotifyAction 7.1.259.6.10.94.1.14.2.26
This variable is for trap var binding, indicated the action of MAC operation. add(1), remove(2).
OBJECT-TYPE    
  INTEGER add(1), remove(2)  

trapIfIndex 7.1.259.6.10.94.1.14.2.30
This variable is for trap var binding, indicating the index of an interface.
OBJECT-TYPE    
  Unsigned32  

trapVlanId 7.1.259.6.10.94.1.14.2.31
This variable is for trap var binding, indicating the identifier of a VLAN.
OBJECT-TYPE    
  Unsigned32  

trapPortSecurityIntrusionMac 7.1.259.6.10.94.1.14.2.29
This variable indicates the intrusion MAC address.
OBJECT-TYPE    
  MacAddress  

rateLimitMgt 7.1.259.6.10.94.1.16.1
OBJECT IDENTIFIER    

rateLimitPortTable 7.1.259.6.10.94.1.16.1.2
Table for rate limit of each port.
OBJECT-TYPE    
  SEQUENCE OF  
    RateLimitPortEntry

rateLimitPortEntry 7.1.259.6.10.94.1.16.1.2.1
Entry for rate limit of each port.
OBJECT-TYPE    
  RateLimitPortEntry  

rlPortIndex 7.1.259.6.10.94.1.16.1.2.1.1
The port and the trunk (including trunk member) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Integer32  

rlPortInputStatus 7.1.259.6.10.94.1.16.1.2.1.6
Whether input rate limit is enabled for this port.
OBJECT-TYPE    
  EnabledStatus  

rlPortOutputStatus 7.1.259.6.10.94.1.16.1.2.1.7
Whether output rate limit is enabled for this port.
OBJECT-TYPE    
  EnabledStatus  

rlPortInputLimitInKilo 7.1.259.6.10.94.1.16.1.2.1.10
Value of the input rate limit. Its unit is kilobits per second. For a 100 Mbps port, the range is 64 to 100000. For a 1000 Mbps port, the range is 64 to 1000000.
OBJECT-TYPE    
  Integer32  

rlPortOutputLimitInKilo 7.1.259.6.10.94.1.16.1.2.1.11
Value of the output rate limit. Its unit is kilobits per second. For a 100 Mbps port, the range is 64 to 100000. For a 1000 Mbps port, the range is 64 to 1000000.
OBJECT-TYPE    
  Integer32  

diffServMgt 7.1.259.6.10.94.1.16.4
OBJECT IDENTIFIER    

diffServPortTable 7.1.259.6.10.94.1.16.4.9
Table for differentiated services on each port.
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServPortEntry

diffServPortEntry 7.1.259.6.10.94.1.16.4.9.1
Entry for differentiated services on each port.
OBJECT-TYPE    
  DiffServPortEntry  

diffServPortIfIndex 7.1.259.6.10.94.1.16.4.9.1.1
This object is the interface index of diffServPortEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
OBJECT-TYPE    
  Integer32  

diffServPortPolicyMapIndex 7.1.259.6.10.94.1.16.4.9.1.2
Specifies the policy map binding to the interface. The policy map identified by a particular value of this index is associated with the same DiffServPolicyMapEntry as identified by the same value of diffServPolicyMapIndex.
OBJECT-TYPE    
  Integer32  

diffServPortIngressIpAclIndex 7.1.259.6.10.94.1.16.4.9.1.3
Specifies the ingress IP ACL binding to the interface. The ingress IP ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex.
OBJECT-TYPE    
  Integer32  

diffServPortIngressMacAclIndex 7.1.259.6.10.94.1.16.4.9.1.4
Specifies the ingress MAC ACL binding to the interface. The ingress MAC ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex.
OBJECT-TYPE    
  Integer32  

diffServPortIngressIpv6AclIndex 7.1.259.6.10.94.1.16.4.9.1.5
Specifies the ingress IPv6 ACL binding to the interface. The ingress IPv6 ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex.
OBJECT-TYPE    
  Integer32  

diffServPolicyMapTable 7.1.259.6.10.94.1.16.4.10
Table for policy map.
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServPolicyMapEntry

diffServPolicyMapEntry 7.1.259.6.10.94.1.16.4.10.1
Entry for policy map.
OBJECT-TYPE    
  DiffServPolicyMapEntry  

diffServPolicyMapIndex 7.1.259.6.10.94.1.16.4.10.1.1
An index that uniquely identifies an entry in this table.
OBJECT-TYPE    
  Integer32  

diffServPolicyMapName 7.1.259.6.10.94.1.16.4.10.1.2
The name of this entry.
OBJECT-TYPE    
  DisplayString Size(1..16)  

diffServPolicyMapDescription 7.1.259.6.10.94.1.16.4.10.1.3
The description of this entry.
OBJECT-TYPE    
  DisplayString Size(0..64)  

diffServPolicyMapElementIndexList 7.1.259.6.10.94.1.16.4.10.1.4
The octet string containes the diffServPolicyMapElementEntry indexes. Two octets express one index and it is represented in network order. This index list indicates the diffServPolicyMapEntrys which belong to this entry.
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

diffServPolicyMapStatus 7.1.259.6.10.94.1.16.4.10.1.5
This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active');it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
OBJECT-TYPE    
  RowStatus  

diffServPolicyMapAttachCtl 7.1.259.6.10.94.1.16.4.11
OBJECT IDENTIFIER    

diffServPolicyMapAttachCtlIndex 7.1.259.6.10.94.1.16.4.11.1
Index for attachment control. Specifies the policy map as the target to relate with the policy map element. The policy map identified by a particular value of this index is associated with the same diffServPolicyMapEntry as identified by the same value of diffServPolicyMapIndex.
OBJECT-TYPE    
  Integer32  

diffServPolicyMapAttachCtlElementIndex 7.1.259.6.10.94.1.16.4.11.2
Element Index for attachment control.Specifies the policy map element to relate with the policy map. The policy map element identified by a particular value of this index is associated with the same diffServPolicyMapElementEntry as identified by the same value of diffServPolicyMapElementIndex.
OBJECT-TYPE    
  Integer32  

diffServPolicyMapAttachCtlAction 7.1.259.6.10.94.1.16.4.11.3
Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular policy map element is attached to a particular policy map. When setting this object to detach(3) to begin the not attached operation, a particular policy map element is not attached to a particular policy map. When the action is finshed or no action is taken, the value of this object is noAction(1). A particular policy map is specified in the diffServPolicyMapAttachCtlIndex. A particularpolicy map element is specified in the diffServPolicyMapAttachCtlElementIndex.
OBJECT-TYPE    
  INTEGER noAction(1), attach(2), detach(3)  

diffServPolicyMapElementTable 7.1.259.6.10.94.1.16.4.12
Table for policy map element.
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServPolicyMapElementEntry

diffServPolicyMapElementEntry 7.1.259.6.10.94.1.16.4.12.1
Entry for policy map element.
OBJECT-TYPE    
  DiffServPolicyMapElementEntry  

diffServPolicyMapElementIndex 7.1.259.6.10.94.1.16.4.12.1.1
An index that uniquely identifies an entry in this table.
OBJECT-TYPE    
  Integer32  

diffServPolicyMapElementClassMapIndex 7.1.259.6.10.94.1.16.4.12.1.2
Specifies the class map binding to this entry. The class map identified by a particular value of this index is associated with the same diffServClassMapEntry as identified by the same value of diffServClassMapIndex.
OBJECT-TYPE    
  Integer32 1..65535  

diffServPolicyMapElementMeterIndex 7.1.259.6.10.94.1.16.4.12.1.3
Specifies the meter binding to this entry. The meter identified by a particular value of this index is associated with the same diffServMeterEntry as identified by the same value of diffServMeterIndex. If this value is zero, no associated meter will be associated, as zero is not a valid meter index.
OBJECT-TYPE    
  Integer32  

diffServPolicyMapElementActionIndex 7.1.259.6.10.94.1.16.4.12.1.4
Specifies the action binding to this entry. The action identified by a particular value of this index is associated with the same diffServActionEntry as identified by the same value of diffServActionIndex.
OBJECT-TYPE    
  Integer32 1..65535  

diffServPolicyMapElementStatus 7.1.259.6.10.94.1.16.4.12.1.5
This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
OBJECT-TYPE    
  RowStatus  

diffServClassMapTable 7.1.259.6.10.94.1.16.4.13
Table for class map.
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServClassMapEntry

diffServClassMapEntry 7.1.259.6.10.94.1.16.4.13.1
Entry for class map.
OBJECT-TYPE    
  DiffServClassMapEntry  

diffServClassMapIndex 7.1.259.6.10.94.1.16.4.13.1.1
An index that uniquely identifies an entry in this table.
OBJECT-TYPE    
  Integer32  

diffServClassMapName 7.1.259.6.10.94.1.16.4.13.1.2
The name of this entry.
OBJECT-TYPE    
  DisplayString Size(1..16)  

diffServClassMapDescription 7.1.259.6.10.94.1.16.4.13.1.3
The description of this entry.
OBJECT-TYPE    
  DisplayString Size(0..64)  

diffServClassMapMatchType 7.1.259.6.10.94.1.16.4.13.1.4
The map match type of this entry.
OBJECT-TYPE    
  INTEGER matchAny(1), matchAll(2)  

diffServClassMapElementIndexTypeList 7.1.259.6.10.94.1.16.4.13.1.5
The octet string containes the type of class map element indexes. Two octets which are represented in network order express one type of the class map element index in network order and it maps the index of differServClasssMapElementIndexList in order. When the type is macAce(1), the maping index of differServClasssMapElementIndexList is the diffServMacAceEntry. When the type is ipAce(2), the maping index of differServClasssMapElementIndexList is the diffServIpAceEntry. When the type is acl(3), the maping index of differServClasssMapElementIndexList is the diffServAclEntry.
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

diffServClassMapElementIndexList 7.1.259.6.10.94.1.16.4.13.1.6
The octet string containes the class map element indexes. Two octets express one index and it is represented in network order. This index list indicates the particular class map elements which belong to this table. The class map element uses type to indicate diffServAclEntry, the diffServIpAceEntry or diffServMacAceEntry. The type is two octet specified in differServClasssMapElementIndexTypeList in order. When the type is macAce(1), the maping index of differServClasssMapElementIndexList is the diffServMacAceEntry. When the type is ipAce(2), the maping index of differServClasssMapElementIndexList is the diffServIpAceEntry. When the type is acl(3), the maping index of differServClasssMapElementIndexList is the diffServAclEntry.
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

diffServClassMapStatus 7.1.259.6.10.94.1.16.4.13.1.7
This object is used to create a new row or modify or delete an existing row in this table.The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
OBJECT-TYPE    
  RowStatus  

diffServClassMapAttachCtl 7.1.259.6.10.94.1.16.4.14
OBJECT IDENTIFIER    

diffServClassMapAttachCtlIndex 7.1.259.6.10.94.1.16.4.14.1
Index for attachment control. Specifies the class map as the target to relate with class map elements. The class map identified by a particular value of this index is associated with the same diffServClassMapEntry as identified by the same value of diffServClassMapIndex.
OBJECT-TYPE    
  Integer32  

diffServClassMapAttachCtlElementIndexType 7.1.259.6.10.94.1.16.4.14.2
Element Index for attachment control. Specifies the type of class map element to relate with the class map. When type is macAce(1), the index of diffServClassMapAttachCtlElementIndex is the index of diffServMacAceEntry. When the type is ipAce(2), the index of diffServClassMapAttachCtlElementIndex is the index of diffServIpAceEntry. When the type is acl(3), the index of diffServClassMapAttachCtlElementIndex is the index of diffServAclEntry.
OBJECT-TYPE    
  INTEGER macAce(1), ipAce(2), acl(3)  

diffServClassMapAttachCtlElementIndex 7.1.259.6.10.94.1.16.4.14.3
Element Index for attachment control. Specifies the class map element related with the class map. The class map element uses type to indicate diffServAclEntry, the diffServIpAceEntry or diffServMacAceEntry. The type is specified in diffServClassMapAttachCtlElementIndexType. When the type is macAce(1), the maping index of differServClasssMapElementIndexList is the diffServMacAceEntry. When the type is ipAce(2), the maping index of differServClasssMapElementIndexList is the diffServIpAceEntry. When the type is acl(3), the maping index of differServClasssMapElementIndexList is the diffServAclEntry.
OBJECT-TYPE    
  Integer32  

diffServClassMapAttachCtlAction 7.1.259.6.10.94.1.16.4.14.4
Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular class map element is attached to a particular class map. When setting this object to detach(3) to begin the not attached operation, then a particular class map element is not attached to a particular class map. When the action is finshed whether successfully or not, or no action is taken, the value of this object always is noAction(1). The value of a particular class map is specified in the AclAttachCtlTargetIndex. The class map element is specified by diffServClassMapAttachCtlElementIndexType and diffServClassMapAttachCtlElementIndex.
OBJECT-TYPE    
  INTEGER noAction(1), attach(2), detach(3)  

diffServAclTable 7.1.259.6.10.94.1.16.4.15
Table for ACL.
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServAclEntry

diffServAclEntry 7.1.259.6.10.94.1.16.4.15.1
Entry for ACL.
OBJECT-TYPE    
  DiffServAclEntry  

diffServAclIndex 7.1.259.6.10.94.1.16.4.15.1.1
An index that uniquely identifies an entry in the ACL table.
OBJECT-TYPE    
  Integer32  

diffServAclName 7.1.259.6.10.94.1.16.4.15.1.2
The name of this entry.
OBJECT-TYPE    
  DisplayString Size(1..16)  

diffServAclType 7.1.259.6.10.94.1.16.4.15.1.3
The type of this entry. When the value of ACL type is modified, then the ACEs in the diffServAclAceIndexList of this entry will be auto-removed, and this entry will be auto- unbound from the diffServPortTable and the diffServClassMapTable.
OBJECT-TYPE    
  INTEGER mac(1), ipstandard(2), ipextended(3), ipv6standard(4), ipv6extended(5), arp(6)  

diffServAclAceIndexList 7.1.259.6.10.94.1.16.4.15.1.4
The octet string containes the ACE indexes. Two octets express one index and it is represented in network order. This index list indicates the particular ACEs which belong to this table. The ACE uses type to indicate the diffServMacAceEntry, the diffServIpAceEntry, the diffServIpv6AceEntry or the diffServArpAceEntry. The type is specified in diffServAclType. When the type is mac(1), the index of diffServAclAceIndexList is the diffServMacAceEntry. When the type is ipstandard(2) or ipextended(3), the index of diffServAclAceIndexList is the diffServIpAceEntry. When the type is ipv6standard(4) or ipv6extended(5), the index of diffServAclAceIndexList is the diffServIpv6AceEntry. When the type is arp(6), the index of diffServAclAceIndexList is the diffServArpAceEntry.
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

diffServAclStatus 7.1.259.6.10.94.1.16.4.15.1.5
This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
OBJECT-TYPE    
  RowStatus  

diffServAclAttachCtl 7.1.259.6.10.94.1.16.4.16
OBJECT IDENTIFIER    

diffServAclAttachCtlIndex 7.1.259.6.10.94.1.16.4.16.1
Index for attachment control. Specifies the ACL as the target to relate with the IP ACE, the MAC ACE or IPv6 ACE. The ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex.
OBJECT-TYPE    
  Integer32  

diffServAclAttachCtlAceType 7.1.259.6.10.94.1.16.4.16.2
Type for attachment control. Specifies the type of diffServAclAttachCtlAceIndex to relate with the diffServAclAttachCtlIndex. When the type is macAce(1), the index of diffServAclAceIndexList is the diffServMacAceEntry. When the type is ipAce(2), the index of diffServAclAceIndexList is the diffServIpAceEntry. When the type is ipv6Ace(3), the index of diffServAclAceIndexList is the diffServIpv6AceEntry. When the type is arpAce(4), the index of diffServAclAceIndexList is the diffServArpAceEntry.
OBJECT-TYPE    
  INTEGER macAce(1), ipAce(2), ipv6Ace(3), arpAce(4)  

diffServAclAttachCtlAceIndex 7.1.259.6.10.94.1.16.4.16.3
Index for attachment control. Specifies the ACE to relate with the diffServAclAttachCtlIndex. When diffServAclAttachCtlAceType is macAce(1), the value of diffServAclAttachCtlIndex is the diffServMacAceEntry. When diffServAclAttachCtlAceType is ipAce(2), the value of diffServAclAttachCtlIndex is the diffServIpAceEntry. When diffServAclAttachCtlAceType is ipv6Ace(3), the value of diffServAclAttachCtlIndex is the diffServIpv6AceEntry. When diffServAclAttachCtlAceType is arpAce(4), the value of diffServAclAttachCtlIndex is the diffServArpAceEntry.
OBJECT-TYPE    
  Integer32  

diffServAclAttachCtlAction 7.1.259.6.10.94.1.16.4.16.4
Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular ACE is attached to a particular ACL. When setting this object to detach(3) to begin the not attached operation, then a particular ACE is not attached to a particular ACL. When the action is finshed whether successfully or not, or no action is taken, the value of this object always is noAction(1), The value of a particular ACL is specified in the diffServAclAttachCtlAceType and diffServAclAttachCtlAceIndex.
OBJECT-TYPE    
  INTEGER noAction(1), attach(2), detach(3)  

diffServIpAceTable 7.1.259.6.10.94.1.16.4.17
Table for IP ACE.
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServIpAceEntry

diffServIpAceEntry 7.1.259.6.10.94.1.16.4.17.1
Entry for IP ACE.
OBJECT-TYPE    
  DiffServIpAceEntry  

diffServIpAceIndex 7.1.259.6.10.94.1.16.4.17.1.1
An index that uniquely identifies an entry in the IP ACE table.
OBJECT-TYPE    
  Integer32  

diffServIpAceType 7.1.259.6.10.94.1.16.4.17.1.2
The specified IP ACE type. When the type of this entry is modified, then this entry will be auto-unbound from the diffServAclEntry and the not supporting field of this entry will be set 0.
OBJECT-TYPE    
  INTEGER standard(1), extended(2)  

diffServIpAceAccess 7.1.259.6.10.94.1.16.4.17.1.3
Indicates the action to be taken if a packet matches this ACE.
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

diffServIpAceSourceIpAddr 7.1.259.6.10.94.1.16.4.17.1.4
The specified source IP address. The packet's source address is AND-ed with the value of IpAceSourceIpAddrBitmask and then compared against the value of this object.
OBJECT-TYPE    
  IpAddress  

diffServIpAceSourceIpAddrBitmask 7.1.259.6.10.94.1.16.4.17.1.5
The specified source IP address mask. The packet's source address is AND-ed with the value of IpAceSourceIpAddr and then compared against the value of this object.
OBJECT-TYPE    
  IpAddress  

diffServIpAceDestIpAddr 7.1.259.6.10.94.1.16.4.17.1.6
The specified destination IP address. The packet's destination address is AND-ed with the value of diffServIpAceDestIpAddrBitmask and then compared against the value of this object. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  IpAddress  

diffServIpAceDestIpAddrBitmask 7.1.259.6.10.94.1.16.4.17.1.7
The specified destination IP address mask. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  IpAddress  

diffServIpAceProtocol 7.1.259.6.10.94.1.16.4.17.1.8
The protocol number field in the IP header used to indicate the higher layer protocol as specified in RFC 1700. A value of 0 matches every IP packet. The object=256 means 'any'. For example: 0 is IP, 1 is ICMP, 2 is IGMP, 4 is IP in IP encapsulation, 6 is TCP, 9 is IGRP, 17 is UDP, 47 is GRE, 50 is ESP, 51 is AH, 88 is IGRP, 89 is OSPF, 94 is KA9Q/NOS compatible IP over IP, 103 is PIMv2, 108 is PCP. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  Integer32 0..256  

diffServIpAcePrec 7.1.259.6.10.94.1.16.4.17.1.9
Specifies the IP precedence value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 8. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  Integer32 0..8  

diffServIpAceTos 7.1.259.6.10.94.1.16.4.17.1.10
Specifies the IP ToS facility value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 9. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  Integer32 0..16  

diffServIpAceDscp 7.1.259.6.10.94.1.16.4.17.1.11
Specifies the DSCP value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 64. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  Integer32 0..64  

diffServIpAceSourcePortOp 7.1.259.6.10.94.1.16.4.17.1.12
Indicates how a packet's source TCP/UDP port number is to be compared. noOperator(1), which is the default value, means no comparison is to be made with the source TCP/UDP port number. equal(2), which is used the diffServIpAceSourcePortBitmask and the diffServIpAceMinSourcePort to match against. range(3),which is used the diffServIpAceMinSourcePort and the diffServIpAceMaxSourcePort to match against. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  INTEGER noOperator(1), equal(2), range(3)  

diffServIpAceMinSourcePort 7.1.259.6.10.94.1.16.4.17.1.13
If the diffServIpAceSourcePortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  Integer32 0..FFFF  

diffServIpAceSourcePortBitmask 7.1.259.6.10.94.1.16.4.17.1.15
If the diffServIpAceSourcePortOp is equal(2), this indicates the bitmask of the diffServIpAceMinSourcePort. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  Integer32 0..FFFF  

diffServIpAceDestPortOp 7.1.259.6.10.94.1.16.4.17.1.16
Indicates how a packet's destination TCP/UDP port number is to be compared. noOperator(1), which is the default value, means that no comparison is to be made with the destination TCP/UDP port number. equal(2), which is used the diffServIpAceSourcePortBitmask and the diffServIpAceMinDestPort to match against. range(3),which is used the diffServIpAceMinDestPort and the diffServIpAceMaxDestPort to match against. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  INTEGER noOperator(1), equal(2), range(3)  

diffServIpAceMinDestPort 7.1.259.6.10.94.1.16.4.17.1.17
If the diffServIpAceDestPortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  Integer32 0..FFFF  

diffServIpAceDestPortBitmask 7.1.259.6.10.94.1.16.4.17.1.19
If the diffServIpAceDestPortOp is equal(2), this indicates the bitmask of the diffServIpAceMinDestPort. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  Integer32 0..FFFF  

diffServIpAceControlCode 7.1.259.6.10.94.1.16.4.17.1.20
Indicates how the control flags of TCP packets are to be compared. diffServIpAceControlCode is AND-ed with diffServIpAceControlCodeBitmask. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  Integer32 0..63  

diffServIpAceControlCodeBitmask 7.1.259.6.10.94.1.16.4.17.1.21
Indicates how the control flags of TCP packets are to be compared. It can be used to check multiple flags of the FIN, SYN, RST, PSH, ACK, URG by the sum of FIN=1, SYN=2, RST=4, PSH=8, ACK=16, URG=32. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
OBJECT-TYPE    
  Integer32 0..63  

diffServIpAceStatus 7.1.259.6.10.94.1.16.4.17.1.22
This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
OBJECT-TYPE    
  RowStatus  

diffServMacAceTable 7.1.259.6.10.94.1.16.4.18
Table for MAC ACE.
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServMacAceEntry

diffServMacAceEntry 7.1.259.6.10.94.1.16.4.18.1
Entry for MAC ACE.
OBJECT-TYPE    
  DiffServMacAceEntry  

diffServMacAceIndex 7.1.259.6.10.94.1.16.4.18.1.1
An index that uniquely identifies an entry in the MAC ACE table.
OBJECT-TYPE    
  Integer32  

diffServMacAceAccess 7.1.259.6.10.94.1.16.4.18.1.2
Indicates the action to be taken if a packet matches this ACE.
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

diffServMacAcePktformat 7.1.259.6.10.94.1.16.4.18.1.3
Used to check the packet format of the packets. This object cannot be configured when the status of the entry, diffServMacAceStatus, is active(1).
OBJECT-TYPE    
  INTEGER any(1), untagged-Eth2(2), untagged802Dot3(3), tagggedEth2(4), tagged802Dot3(5)  

diffServMacAceSourceMacAddr 7.1.259.6.10.94.1.16.4.18.1.4
Indicates the 48-bit source MAC address. The specified source MAC of the packet. The packet's source MAC address is AND-ed with the value of diffServMacAceSourceMacAddrBitmask and then compared against the value of this object.
OBJECT-TYPE    
  MacAddress  

diffServMacAceSourceMacAddrBitmask 7.1.259.6.10.94.1.16.4.18.1.5
The specified source MAC address mask.
OBJECT-TYPE    
  MacAddress  

diffServMacAceDestMacAddr 7.1.259.6.10.94.1.16.4.18.1.6
Indicates the 48-bit destination MAC address. The specified destination MAC of the packet. The packet's destination MAC address is AND-ed with the value of diffServMacAceDestMacAddrBitmask and then compared against the value of this object.
OBJECT-TYPE    
  MacAddress  

diffServMacAceDestMacAddrBitmask 7.1.259.6.10.94.1.16.4.18.1.7
The specified destination MAC address mask.
OBJECT-TYPE    
  MacAddress  

diffServMacAceVidOp 7.1.259.6.10.94.1.16.4.18.1.8
Indicates how a packet's VID is to be compared. This object cannot be configured when the status of the entry, diffServMacAceStatus, is active(1).
OBJECT-TYPE    
  INTEGER noOperator(1), equal(2), range(3)  

diffServMacAceMinVid 7.1.259.6.10.94.1.16.4.18.1.9
Indicates the lower bound of the VID value range if the diffServMacAceVidOp is range(3).
OBJECT-TYPE    
  Integer32 1..4094  

diffServMacAceVidBitmask 7.1.259.6.10.94.1.16.4.18.1.10
The bit mask of the VID. The default value is 0.
OBJECT-TYPE    
  Integer32 0..0FFF  

diffServMacAceEtherTypeOp 7.1.259.6.10.94.1.16.4.18.1.12
Indicates how a packet's ether type is to be compared.
OBJECT-TYPE    
  INTEGER noOperator(1), equal(2), range(3)  

diffServMacAceEtherTypeBitmask 7.1.259.6.10.94.1.16.4.18.1.13
The bit mask of Ether type. The default value is 0.
OBJECT-TYPE    
  Integer32 0..FFFF  

diffServMacAceMinEtherType 7.1.259.6.10.94.1.16.4.18.1.14
Indicates the lower bound of the ether type value range if the diffServMacAceEtherTypeOp is range(3).
OBJECT-TYPE    
  Integer32 0000..FFFF  

diffServMacAceStatus 7.1.259.6.10.94.1.16.4.18.1.16
This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
OBJECT-TYPE    
  RowStatus  

diffServMacAceCosOp 7.1.259.6.10.94.1.16.4.18.1.17
Indicates how a packet's CoS is compared. If the object type of diffServMacAceCosOp is equal(2), diffServMacAceMinCos indicates the CoS value for comparing, and diffServMacAceCosBitmask is used as the bitmask of the CoS value. If the object type of diffServMacAceCosOp is range(3), diffServMacAceMinCos should be used as the lower bound of the CoS value.
OBJECT-TYPE    
  INTEGER noOperator(1), equal(2), range(3)  

diffServMacAceCosBitmask 7.1.259.6.10.94.1.16.4.18.1.18
Indicates the bitmask of the CoS value if the object type of diffServMacAceCosOp is equal(2). The default value is 0.
OBJECT-TYPE    
  INTEGER 0..7  

diffServMacAceMinCos 7.1.259.6.10.94.1.16.4.18.1.19
If the object type of diffServMacAceCosOp is equal(2), diffServMacAceMinCos indicates the CoS value for comparing. If the object type of diffServMacAceCosOp is range(3), diffServMacAceMinCos indicates the lower bound of the CoS value.
OBJECT-TYPE    
  INTEGER 0..7  

diffServActionTable 7.1.259.6.10.94.1.16.4.19
Table for action.
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServActionEntry

diffServActionEntry 7.1.259.6.10.94.1.16.4.19.1
Entry for action.
OBJECT-TYPE    
  DiffServActionEntry  

diffServActionIndex 7.1.259.6.10.94.1.16.4.19.1.1
An index that uniquely identifies an entry in the action table.
OBJECT-TYPE    
  Integer32  

diffServActionList 7.1.259.6.10.94.1.16.4.19.1.2
The bitmap value used to identify which action capabilities are enabled on the entry. The actionPktNewPri and actionPktNewDscp can not be enabled at the same time on the entry. The actionRedPktNewDscp and actionRedDrop can not be enabled at the same time on the entry.
OBJECT-TYPE    
  BITS actionPktNewPri(0), actionPktNewDscp(2), actionRedPktNewDscp(3), actionRedDrop(4)  

diffServActionPktNewPri 7.1.259.6.10.94.1.16.4.19.1.3
Specifies the new priority value for the packet when the action is satisfied. If the actionPktNewPri bit of the diffServActionList is not enabled, this object can not be set.
OBJECT-TYPE    
  Integer32 0..7  

diffServActionPktNewDscp 7.1.259.6.10.94.1.16.4.19.1.5
Specifies the new DSCP value for the packet when the action is satisfied. If the actionPktNewDscp bit of the diffServActionList is not enabled, this object can not be set.
OBJECT-TYPE    
  Integer32 0..63  

diffServActionRedPktNewDscp 7.1.259.6.10.94.1.16.4.19.1.6
Specifies the new DSCP value for the red marking packet when the action is satisfied. If the actionRedPktNewDscp bit of the diffServActionList is not enabled, this object can not be set.
OBJECT-TYPE    
  Integer32 0..63  

diffServActionRedDrop 7.1.259.6.10.94.1.16.4.19.1.7
The actionRedDrop bit of the diffServActionList is for configuring this object. If the value of this object is enabled, the red marking packet will be dropped.
OBJECT-TYPE   <