ERI-DNX-STS1-MIB

File: ERI-DNX-STS1-MIB.mib (38572 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC ERI-ROOT-SMI
ERI-DNX-SMC-MIB

Imported symbols

MODULE-IDENTITY OBJECT-IDENTITY OBJECT-TYPE
Integer32 Counter32 NOTIFICATION-TYPE
DisplayString TEXTUAL-CONVENTION eriMibs
devices PortStatus DecisionType
FunctionSwitch LinkPortAddress LinkCmdStatus
trapSequence

Defined Types

VtGroupType  
Indicates the type of Virtual Tributaries (VT) grouping option used on the links. VT 1.5 is used to group T1 links into 7 groups of 4 for the 28 links. VT 2.0 is used to group E1 links into 7 groups of 3 for the 21 links. Using the VT 2.0, links divisible by 4 are skipped over and not used.
TEXTUAL-CONVENTION    
  INTEGER vt2-0-e1(0), vt1-5-ds1(1)  

STS1MapperConfigEntry  
SEQUENCE    
  sts1MapperAddr LinkPortAddress
  sts1MapperResource Integer32
  sts1VtGroup1 VtGroupType
  sts1VtGroup2 VtGroupType
  sts1VtGroup3 VtGroupType
  sts1VtGroup4 VtGroupType
  sts1VtGroup5 VtGroupType
  sts1VtGroup6 VtGroupType
  sts1VtGroup7 VtGroupType
  sts1VtMapping INTEGER
  sts1Timing INTEGER
  sts1ShortCable FunctionSwitch
  sts1MaprCmdStatus LinkCmdStatus

STS1T1E1LinkConfigEntry  
SEQUENCE    
  sts1T1E1CfgLinkAddr LinkPortAddress
  sts1T1E1CfgResource Integer32
  sts1T1E1CfgLinkName DisplayString
  sts1T1E1Status PortStatus
  sts1T1E1Clear INTEGER
  sts1T1E1Framing INTEGER
  sts1T1E1NetLoop INTEGER
  sts1T1E1YelAlrm INTEGER
  sts1T1E1RecoverTime INTEGER
  sts1T1E1EsfFormat INTEGER
  sts1T1E1IdleCode INTEGER
  sts1T1E1CfgCmdStatus LinkCmdStatus
  sts1T1E1Gr303Facility DecisionType

STS1MapperStatusEntry  
SEQUENCE    
  sts1MapperStatusAddr LinkPortAddress
  sts1MapperStatusResource Integer32
  sts1MapperStatusState INTEGER
  sts1MapperStatusLOSErrs Counter32
  sts1MapperStatusOOFErrs Counter32
  sts1MapperStatusLOFErrs Counter32
  sts1MapperStatusLOPtrErrs Counter32
  sts1MapperStatusAISErrs Counter32
  sts1MapperStatusMultiFErrs Counter32
  sts1MapperStatusRxTraceErrs Counter32
  sts1MapperStatusTotErrSecs Counter32
  sts1MapperStatusCmdStatus INTEGER

STS1LIUEntry  
SEQUENCE    
  sts1LIUAddr LinkPortAddress
  sts1LIUResource Integer32
  sts1LIUBertState INTEGER
  sts1LIUBertErrSecs Counter32
  sts1LIUBertDuration Counter32
  sts1LIULoopType INTEGER
  sts1LIUDigitalErrs Counter32
  sts1LIUAnalogErrs Counter32
  sts1LIUExcessZeros Counter32
  sts1LIUCodingViolationErrs Counter32
  sts1LIUPRBSErrs Counter32
  sts1LIUCmdStatus INTEGER

Defined Values

eriDNXSts1MIB 1.3.6.1.4.1.644.3.4
The ERI Enterprise MIB Module for the DNX STS1 Device.
MODULE-IDENTITY    

dnxSTS1 1.3.6.1.4.1.644.2.4.2.3
OBJECT IDENTIFIER    

sts1Config 1.3.6.1.4.1.644.2.4.2.3.1
OBJECT IDENTIFIER    

sts1Diag 1.3.6.1.4.1.644.2.4.2.3.2
OBJECT IDENTIFIER    

sts1MapperConfigTable 1.3.6.1.4.1.644.2.4.2.3.1.1
This is the STS-1 Mapper LIU Configuration table which consists of an entry for each of the STS-1 cards. The total number of entries depends on the number of STS-1 cards in the nest.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    STS1MapperConfigEntry

sts1MapperConfigEntry 1.3.6.1.4.1.644.2.4.2.3.1.1.1
The conceptual row of the STS-1 Mapper LIU Configuration table. A row in this table cannot be added or deleted, only modified.
Status: current Access: not-accessible
OBJECT-TYPE    
  STS1MapperConfigEntry  

sts1MapperAddr 1.3.6.1.4.1.644.2.4.2.3.1.1.1.1
This number uniquely identifies a STS-1 slot/mapper.
Status: current Access: read-only
OBJECT-TYPE    
  LinkPortAddress  

sts1MapperResource 1.3.6.1.4.1.644.2.4.2.3.1.1.1.2
Uniquely identifies an STS1 Device in the system. This number is provided as key to allow the manager to map this entry to a corresponding Resource Table entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sts1VtGroup1 1.3.6.1.4.1.644.2.4.2.3.1.1.1.3
Indicates the type of grouping option used to on links 1 through 4. Using the VT 2.0, link 4 is not used.
Status: current Access: read-only
OBJECT-TYPE    
  VtGroupType  

sts1VtGroup2 1.3.6.1.4.1.644.2.4.2.3.1.1.1.4
Indicates the type of grouping option used to on links 5 through 8. Using the VT 2.0, link 8 is not used.
Status: current Access: read-only
OBJECT-TYPE    
  VtGroupType  

sts1VtGroup3 1.3.6.1.4.1.644.2.4.2.3.1.1.1.5
Indicates the type of grouping option used to on links 9 through 12. Using the VT 2.0, link 12 is not used.
Status: current Access: read-only
OBJECT-TYPE    
  VtGroupType  

sts1VtGroup4 1.3.6.1.4.1.644.2.4.2.3.1.1.1.6
Indicates the type of grouping option used to on links 13 through 16. Using the VT 2.0, link 16 is not used.
Status: current Access: read-only
OBJECT-TYPE    
  VtGroupType  

sts1VtGroup5 1.3.6.1.4.1.644.2.4.2.3.1.1.1.7
Indicates the type of grouping option used to on links 17 through 20. Using the VT 2.0, link 20 is not used.
Status: current Access: read-only
OBJECT-TYPE    
  VtGroupType  

sts1VtGroup6 1.3.6.1.4.1.644.2.4.2.3.1.1.1.8
Indicates the type of grouping option used to on links 21 through 24. Using the VT 2.0, link 24 is not used.
Status: current Access: read-only
OBJECT-TYPE    
  VtGroupType  

sts1VtGroup7 1.3.6.1.4.1.644.2.4.2.3.1.1.1.9
Indicates the type of grouping option used to on links 25 through 28. Using the VT 2.0, link 28 is not used.
Status: current Access: read-only
OBJECT-TYPE    
  VtGroupType  

sts1VtMapping 1.3.6.1.4.1.644.2.4.2.3.1.1.1.10
Indicates the Mapper Standard currently in use.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER standardVT(0), sequencialFrm(1)  

sts1Timing 1.3.6.1.4.1.644.2.4.2.3.1.1.1.11
Indicates whether the STS-1 device uses an internal or external clock source.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER internal(0), ec1-Line(1)  

sts1ShortCable 1.3.6.1.4.1.644.2.4.2.3.1.1.1.12
Indicates the line build out of the STS-1 transmitter. 'enable' when attached to a cable less than 50 feet long.
Status: current Access: read-write
OBJECT-TYPE    
  FunctionSwitch  

sts1MaprCmdStatus 1.3.6.1.4.1.644.2.4.2.3.1.1.1.13
The command status for this link configuration row/record. The value used in a SET will be replaced by a response value in the GET RESPONSE indicating success or failure. Default Response State used in GET RESPONSE Command ready-for-command (0) initial default status for a row STS1 Link Commands used in SET Command (1..199) update-link-config(1), Change existing Link Configuration Response States used in GET RESPONSE Command (200..399) update-successful (201) Link data has been successfully changed STS1 Mapper Config Error Codes used in GET RESPONSE Command (400..699) err-general-link-config-error (400) Unknown link configuration error occurred err-invalid-link-status (401) Unrecognized link status setting err-invalid-link-framing (402) Line framing type not valid for link type err-invalid-link-command (403) Unrecognized link command-action err-invalid-link-op-mode (407) Configured M13 Op mode not valid for port; verify other link parameters match desired new mode err-invalid-link-rem-loop (408) Remote Loop type not valid for sts1 frame type err-invalid-link-ais (409) Unrecognized sts1 AIS selection err-data-locked-by-another-user (450) Another administrative user is making changes to this part of the system via a terminal session. Check Event Log for user name err-snmp-parse-failed (500) Agent could not parse variable err-invalid-snmp-type (501) Variable ASN type does not match Agent defined type err-invalid-snmp-var-size (502) Variable size is too big
Status: current Access: read-write
OBJECT-TYPE    
  LinkCmdStatus  

sts1T1E1LinkConfigTable 1.3.6.1.4.1.644.2.4.2.3.1.2
This is the STS T1/E1 Link Configuration table which consists of an entry for each of the card's 28 links. The total number of entries depends on the number of STS1 cards in the nest.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    STS1T1E1LinkConfigEntry

sts1T1E1LinkConfigEntry 1.3.6.1.4.1.644.2.4.2.3.1.2.1
The conceptual row of the STS T1/E1 Link Configuration table. A row in this table cannot be added or deleted, only modified.
Status: current Access: not-accessible
OBJECT-TYPE    
  STS1T1E1LinkConfigEntry  

sts1T1E1CfgLinkAddr 1.3.6.1.4.1.644.2.4.2.3.1.2.1.1
This number uniquely identifies a STS T1/E1 link resource. This number will be used throughout the system to identify a unique resource.
Status: current Access: read-only
OBJECT-TYPE    
  LinkPortAddress  

sts1T1E1CfgResource 1.3.6.1.4.1.644.2.4.2.3.1.2.1.2
Uniquely identifies an STS T1/E1 Channel in the system. This number is provided as key to allow the manager to map this entry to a corresponding Resource Table entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sts1T1E1CfgLinkName 1.3.6.1.4.1.644.2.4.2.3.1.2.1.3
This is the user friendly text name to identify the link.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

sts1T1E1Status 1.3.6.1.4.1.644.2.4.2.3.1.2.1.4
Dictates the current status of the link, in-service or out-of-service.
Status: current Access: read-write
OBJECT-TYPE    
  PortStatus  

sts1T1E1Clear 1.3.6.1.4.1.644.2.4.2.3.1.2.1.5
Determines if the port supports T1 or E1 unframed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), framed(1), unframed(2)  

sts1T1E1Framing 1.3.6.1.4.1.644.2.4.2.3.1.2.1.6
Determines the type of framing used on the line. Choose between T1 SuperFrame 'D4', Extended SuperFrame (ESF), or T1 Unframed. Currently E1 is not supported. When value of sts1T1E1Clear is set to unframed (2), the only valid framing options are: e1Unframed(4) or t1Unframed(7).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER t1Esf(5), t1D4(6), t1Unframed(7)  

sts1T1E1NetLoop 1.3.6.1.4.1.644.2.4.2.3.1.2.1.7
Determines whether or not the module should respond to loop diagnostic commands received from the network supplier. Select 'enable' unless the commands are to be passed to another STS1 device.
Status: current Access: read-write
OBJECT-TYPE    
  FunctionSwitch  

sts1T1E1YelAlrm 1.3.6.1.4.1.644.2.4.2.3.1.2.1.8
Causes the module to discard data and send a yellow alarm if it is in a red alarm condition after a 3 second period. 'Yes' must be chosen if the network supplier is a common carrier, such as a telephone company.
Status: current Access: read-write
OBJECT-TYPE    
  DecisionType  

sts1T1E1RecoverTime 1.3.6.1.4.1.644.2.4.2.3.1.2.1.9
This is the red alarm timeout value. Determines the amount of seconds the port will wait to stop sending the yellow alarm when coming out of a red alarm condition.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER timeout-3-secs(3), timeout-10-secs(10), timeout-15-secs(15)  

sts1T1E1EsfFormat 1.3.6.1.4.1.644.2.4.2.3.1.2.1.10
Determines the type of ESF network commands the T-1 link will respond to. It has no meaning for D4 networks. With ESF networks, this information must be obtained from the network supplier.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER att-54016(0), ansi-t1-403(1)  

sts1T1E1IdleCode 1.3.6.1.4.1.644.2.4.2.3.1.2.1.11
Determines the whether the code that will be transmitted over the unused links will be 'idle' or 'busy' (all 1's).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER busy(0), idle(1)  

sts1T1E1CfgCmdStatus 1.3.6.1.4.1.644.2.4.2.3.1.2.1.12
The command status for this link configuration row/record. The value used in a SET will be replaced by a response value in the GET RESPONSE indicating success or failure. Default Response State used in GET RESPONSE Command ready-for-command (0) initial default status for a row STS1-T1 Link Commands used in SET Command (1..199) update(1) Change existing Link Configuration inServiceAll (7) Change Link Status to in-service for all 8 links. copyToAll (9) Copy T1 Link configuration to all other links within the same device outOfServiceAll (12) Change Link Status to out-of-service for all 8 links. Response States used in GET RESPONSE Command (100..199) update-successful (101) Link data has been successfully changed insvc-successful (107) All Links have been successfully placed In Service copy-successful (109) T1 Link data has been successfully copied to other links oos-successful (112) All Links have been successfully placed Out of Service STS1-T1 Link Config Error Codes used in GET RESPONSE Command (400..699) err-general-link-config-error (400) Unknown link configuration error occurred err-invalid-link-status (401) Unrecognized link status setting err-invalid-link-framing (402) Line framing type not valid for link type err-invalid-link-command (403) Unrecognized link command-action err-invalid-esf-format (405) ESF type not applicable to link type err-invalid-link-density (406) Unrecognized T1 link density setting err-invalid-network-loop (410) Unrecognized network loop setting err-invalid-yellow-alrm (411) Unrecognized yellow alarm setting err-invalid-red-timeout (412) Unrecognized red alarm timeout err-invalid-idle-code (413) Unrecognized idle code err-device-in-standby (414) Can't change config for designated Standby device err-data-locked-by-another-user (450) Another administrative user is making changes to this part of the system via a terminal session. Check Event Log for user name err-snmp-parse-failed (500) Agent could not parse variable err-invalid-snmp-type (501) Variable ASN type does not match Agent defined type err-invalid-snmp-var-size (502) Variable size is too big
Status: current Access: read-write
OBJECT-TYPE    
  LinkCmdStatus  

sts1T1E1Gr303Facility 1.3.6.1.4.1.644.2.4.2.3.1.2.1.13
Enables link to be configured as a Gr303 Facility
Status: obsolete Access: read-only
OBJECT-TYPE    
  DecisionType  

sts1MapperStatusTable 1.3.6.1.4.1.644.2.4.2.3.2.1
This is the STS-1 Mapper Status table which consists of a single entry for each card's Mapper Display. The total number of entries depends on the number of STS1 cards in the node.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    STS1MapperStatusEntry

sts1MapperStatusEntry 1.3.6.1.4.1.644.2.4.2.3.2.1.1
The conceptual row of the Mapper table. A row in this table cannot be added or deleted, only modified.
Status: current Access: not-accessible
OBJECT-TYPE    
  STS1MapperStatusEntry  

sts1MapperStatusAddr 1.3.6.1.4.1.644.2.4.2.3.2.1.1.1
This number uniquely identifies a STS1 Mapper resource. This number will be used throughout the system to identify a unique resource.
Status: current Access: read-only
OBJECT-TYPE    
  LinkPortAddress  

sts1MapperStatusResource 1.3.6.1.4.1.644.2.4.2.3.2.1.1.2
This number uniquely identifies a STS1 Mapper resource. This number is provided as key to allow the manager to map this entry to a corresponding Resource Table Entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sts1MapperStatusState 1.3.6.1.4.1.644.2.4.2.3.2.1.1.3
Determines the current line condition status of the Mapper. ok (0), lof (32), -- bit 5 lop (256), -- bit 8 oof (512), -- bit 9 ais (1024), -- bit 10 los (8192), -- bit 13 lomf (131072), -- bit 17 errors (2147483647) -- all
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), lof(32), lop(256), oof(512), ais(1024), los(8192), lomf(131072), errors(2147483647)  

sts1MapperStatusLOSErrs 1.3.6.1.4.1.644.2.4.2.3.2.1.1.4
This is the number of seconds a Loss of Signal was declared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1MapperStatusOOFErrs 1.3.6.1.4.1.644.2.4.2.3.2.1.1.5
This is the number of seconds an Out Of Frame alignement error was declared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1MapperStatusLOFErrs 1.3.6.1.4.1.644.2.4.2.3.2.1.1.6
This is the number of seconds a Loss of Frame was declared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1MapperStatusLOPtrErrs 1.3.6.1.4.1.644.2.4.2.3.2.1.1.7
This is the number of seconds a Loss of Pointer was declared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1MapperStatusAISErrs 1.3.6.1.4.1.644.2.4.2.3.2.1.1.8
This is the number of seconds an Alarm Indication Signal was declared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1MapperStatusMultiFErrs 1.3.6.1.4.1.644.2.4.2.3.2.1.1.9
This is the number of seconds a Near End Loss of Multi-Frame Signal was declared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1MapperStatusRxTraceErrs 1.3.6.1.4.1.644.2.4.2.3.2.1.1.10
This is the number of seconds an error has been detected in the receive path trace.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1MapperStatusTotErrSecs 1.3.6.1.4.1.644.2.4.2.3.2.1.1.11
This is the total number of Errored Seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1MapperStatusCmdStatus 1.3.6.1.4.1.644.2.4.2.3.2.1.1.12
This is the command status for the Mapper Row. The value used in a SET will be replaced by a response value in the GET RESPONSE indicating success or failure. Default Response State used in GET RESPONSE Command ready-for-command (0) initial default status for a row Action Commands used in SET Command (1..99) update (1) Can be used optionally when activating loops and berts in order to get status code back in response clearErrors (14) Resets all error counters to zero Response States used in GET RESPONSE Command (100..199) update-successful (101) Test action has been successfully performed clear-successful (114) Error counts have been successfully cleared The Error Codes used in GET RESPONSE Command (200..799) err-general-test-error (200) Unknown Test request error occurred. err-field-cannot-be-set (206) Read-only field was included in SET request err-snmp-parse-failed (500) Agent could not parse variable err-invalid-snmp-type (501) Variable ASN type does not match Agent defined type err-invalid-snmp-var-size (502) Variable size is too big
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ready-for-command(0), update(1), clearErrors(14), update-successful(101), clear-successful(114), err-general-test-error(200), err-field-cannot-be-set(206), err-snmp-parse-failed(500), err-invalid-snmp-type(501), err-invalid-snmp-var-size(502)  

sts1LIUTable 1.3.6.1.4.1.644.2.4.2.3.2.2
This is the STS1 LIU Diagnostic Status table which consists of an entry for each STS1 card's Line Interface Unit Display. The number of entries depends on the number of STS1 cards in the node.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    STS1LIUEntry

sts1LIUEntry 1.3.6.1.4.1.644.2.4.2.3.2.2.1
The conceptual row of the Mapper table. A row in this table cannot be added or deleted, only modified.
Status: current Access: not-accessible
OBJECT-TYPE    
  STS1LIUEntry  

sts1LIUAddr 1.3.6.1.4.1.644.2.4.2.3.2.2.1.1
This number uniquely identifies a STS1 Mapper resource address. This number will be used throughout the system to identify a unique resource.
Status: current Access: read-only
OBJECT-TYPE    
  LinkPortAddress  

sts1LIUResource 1.3.6.1.4.1.644.2.4.2.3.2.2.1.2
This number uniquely identifies a STS1 Mapper resource. This number is provided as a key to allow the manager to map this entry to a corresponding Resource Table Entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sts1LIUBertState 1.3.6.1.4.1.644.2.4.2.3.2.2.1.3
This is the LIU Bert State indicated by on/off.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(45), liu-bert(44)  

sts1LIUBertErrSecs 1.3.6.1.4.1.644.2.4.2.3.2.2.1.4
This is the number of LIU Bert Errored seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1LIUBertDuration 1.3.6.1.4.1.644.2.4.2.3.2.2.1.5
This is the number of seconds for the LIU Bert Duration.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1LIULoopType 1.3.6.1.4.1.644.2.4.2.3.2.2.1.6
Indicates the loopback status of the Mapper/LIU for this STS1 device. off (0) - indicates loopback is disabled mapper (1) - indicates Mapper local data is looped back to itself liu (39)- indicates Line Interface Unit local data is looped back to itself.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(0), mapper(1), liu(39)  

sts1LIUDigitalErrs 1.3.6.1.4.1.644.2.4.2.3.2.2.1.7
This is the number of seconds recorded for the LIU Digital Errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1LIUAnalogErrs 1.3.6.1.4.1.644.2.4.2.3.2.2.1.8
This is the number of seconds recorded for the LIU Analog Errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1LIUExcessZeros 1.3.6.1.4.1.644.2.4.2.3.2.2.1.9
This is the number of seconds LIU Excess zero errors were detected.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1LIUCodingViolationErrs 1.3.6.1.4.1.644.2.4.2.3.2.2.1.10
This is the total number of Errored Seconds for the LIU Coding Violation.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1LIUPRBSErrs 1.3.6.1.4.1.644.2.4.2.3.2.2.1.11
This is the total number of Errored Seconds for the LIU PRBS check.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sts1LIUCmdStatus 1.3.6.1.4.1.644.2.4.2.3.2.2.1.12
This is the command status for the LIU Mapper Row. The value used in a SET will be replaced by a response value in the GET RESPONSE indicating success or failure. Default Response State used in GET RESPONSE Command ready-for-command (0) initial default status for a row LIU Action Commands used in SET Command (1..99) update (1) Can be used optionally when activating loops and berts in order to get status code back in response clearErrors (14) Resets all error counters and bert test time to zero Response States used in GET RESPONSE Command (100..199) update-successful (101) Test action has been successfully performed clear-successful (114) Error counts have been successfully cleared LIU Test Error Codes used in GET RESPONSE Command (200..799) err-general-test-error (200) Unknown Test request error occurred. err-invalid-loop-type (202) Unrecognized loop selection err-invalid-bert-type (203) Unrecognized bert selection err-test-in-progress (205) Requested action cannot be performed during bert err-field-cannot-be-set (206) Read-only field was included in SET request err-snmp-parse-failed (500) Agent could not parse variable err-invalid-snmp-type (501) Variable ASN type does not match Agent defined type err-invalid-snmp-var-size (502) Variable size is too big
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ready-for-command(0), update(1), clearErrors(14), update-successful(101), clear-successful(114), err-general-test-error(200), err-invalid-loop-type(202), err-invalid-bert-type(203), err-test-in-progress(205), err-field-cannot-be-set(206), err-snmp-parse-failed(500), err-invalid-snmp-type(501), err-invalid-snmp-var-size(502)  

dnxSTS1Enterprise 1.3.6.1.4.1.644.2.4.2.3.0
ERI DNX STS1 Enterprise for Alarms/Events
Status: current Access: read-write
OBJECT-IDENTITY    

sts1MapperConfigTrap 1.3.6.1.4.1.644.2.4.2.3.0.1
This trap is used to notify a NMS that a user has updated the Link configuration for a given STS1 Mapper entry.
Status: current Access: read-write
NOTIFICATION-TYPE    

sts1T1E1ConfigTrap 1.3.6.1.4.1.644.2.4.2.3.0.2
This trap is used to notify a NMS that a user has updated the Link configuration for a given STS-1 T1 channel entry.
Status: current Access: read-write
NOTIFICATION-TYPE