ERI-DNX-HDS3-MIB

File: ERI-DNX-HDS3-MIB.mib (51235 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	ERI-ROOT-SMI
ERI-DNX-SMC-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-IDENTITY	OBJECT-TYPE
Integer32	Counter32	NOTIFICATION-TYPE
DisplayString	TEXTUAL-CONVENTION	eriMibs
devices	PortStatus	DecisionType
FunctionSwitch	LinkPortAddress	LinkCmdStatus
trapSequence	OneByteField

Defined Types

DS2GroupType
Indicates the type of DS2/G.747 group type option used on the links. VT 1.5 is used to group T1 links into 7 groups of 4 for the 28 links. VT 2.0 is used to group E1 links into 7 groups of 3 for the 21 links. Using the VT 2.0, links divisible by 4 are skipped over and not used.
TEXTUAL-CONVENTION
	INTEGER	e1(0), ds1(1)

HDS3PortConfigEntry
SEQUENCE
	hds3PortCfgAddr	LinkPortAddress
	hds3PortCfgResource	Integer32
	hds3PortCfgName	DisplayString
	hds3FacilityId	DisplayString
	hds3EquipmentId	DisplayString
	hds3Location	DisplayString
	hds3FrameId	DisplayString
	hds3UnitName	DisplayString
	hds3PortNumber	DisplayString
	hds3Generator	DisplayString
	hds3M13OpMode	INTEGER
	hds3RcvLoopTiming	FunctionSwitch
	hds3ShortCable	DecisionType
	hds3M13RemLoop	INTEGER
	hds3FEACLoopbackReq	FunctionSwitch
	hds3XmtAISLocalLoop	INTEGER
	hds3RcvAIS	INTEGER
	hds3XmtAIS	INTEGER
	hds3DS2Group1	DS2GroupType
	hds3DS2Group2	DS2GroupType
	hds3DS2Group3	DS2GroupType
	hds3DS2Group4	DS2GroupType
	hds3DS2Group5	DS2GroupType
	hds3DS2Group6	DS2GroupType
	hds3DS2Group7	DS2GroupType
	hds3CmdStatus	LinkCmdStatus

HDS3T1E1LinkConfigEntry
SEQUENCE
	hds3T1E1CfgLinkAddr	LinkPortAddress
	hds3T1E1CfgResource	Integer32
	hds3T1E1CfgLinkName	DisplayString
	hds3T1E1Status	PortStatus
	hds3T1E1Clear	INTEGER
	hds3T1E1Framing	INTEGER
	hds3T1E1NetLoop	INTEGER
	hds3T1E1YelAlrm	INTEGER
	hds3T1E1RecoverTime	INTEGER
	hds3T1E1EsfFormat	INTEGER
	hds3T1E1IdleCode	INTEGER
	hds3T1E1CfgCmdStatus	LinkCmdStatus
	hds3T1E1Gr303Facility	DecisionType
	hds3T1E1NationalBits	OneByteField
	hds3T1E1InterNational	OneByteField

HDS3FramerStatusEntry
SEQUENCE
	hds3FramerStatusAddr	LinkPortAddress
	hds3FramerStatusResource	Integer32
	hds3FramerStatusState	INTEGER
	hds3FramerStatusRedAlrmErrSecs	Counter32
	hds3FramerStatusLOSErrSecs	Counter32
	hds3FramerStatusOOFErrSecs	Counter32
	hds3FramerStatusAISErrSecs	Counter32
	hds3FramerStatusRcvIdleErrSecs	Counter32
	hds3FramerStatusFarEndRcvErrSecs	Counter32
	hds3FramerStatusCFAErrSecs	Counter32
	hds3FramerStatusTotErrSecs	Counter32
	hds3FramerStatusPbitParityErrs	Counter32
	hds3FramerStatusCbitParityErrs	Counter32
	hds3FramerStatusFebeErrs	Counter32
	hds3FramerStatusLCVErrs	Counter32
	hds3FramerStatusFramingErrs	Counter32
	hds3FramerStatusExcessZeroErrs	Counter32
	hds3FramerStatusInsErrMode	INTEGER
	hds3FramerStatusCmdStatus	INTEGER

HDS3LIUEntry
SEQUENCE
	hds3LIUAddr	LinkPortAddress
	hds3LIUResource	Integer32
	hds3LIUBertState	INTEGER
	hds3LIUBertErrSecs	Counter32
	hds3LIUBertDuration	Counter32
	hds3LIULoopType	INTEGER
	hds3LIUDigitalErrs	Counter32
	hds3LIUAnalogErrs	Counter32
	hds3LIUExcessZeroErrs	Counter32
	hds3LIUCodingViolationErrs	Counter32
	hds3LIUPRBSCheckErrs	Counter32
	hds3LIUCmdStatus	INTEGER

Defined Values

eriDNXHybridDS3MIB		1.3.6.1.4.1.644.3.5
The ERI Enterprise MIB Module for the DNX HDS3 Device.
MODULE-IDENTITY

dnxHDS3		1.3.6.1.4.1.644.2.4.2.2
OBJECT IDENTIFIER

hds3Config		1.3.6.1.4.1.644.2.4.2.2.1
OBJECT IDENTIFIER

hds3Diag		1.3.6.1.4.1.644.2.4.2.2.2
OBJECT IDENTIFIER

hds3PortConfigTable		1.3.6.1.4.1.644.2.4.2.2.1.1
This is the HDS-3 Port Configuration table which consists of an entry for each of the HDS-3 cards. The total number of entries depends on the number of HDS-3 cards in the nest. This is the HDS-3 DS2/G.747 Configuration table which consists of an entry for each of the HDS-3 cards. The total number of entries depends on the number of HDS-3 cards in the nest.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HDS3PortConfigEntry

hds3PortConfigEntry		1.3.6.1.4.1.644.2.4.2.2.1.1.1
The conceptual row of the HDS-3 Port Configuration table. A row in this table cannot be added or deleted, only modified.
Status: current	Access: not-accessible
OBJECT-TYPE
	HDS3PortConfigEntry

hds3PortCfgAddr		1.3.6.1.4.1.644.2.4.2.2.1.1.1.1
This number uniquely identifies a HDS-3 T1/E1 link resource. This number will be used throughout the system to identify a unique resource.
Status: current	Access: read-only
OBJECT-TYPE
	LinkPortAddress

hds3PortCfgResource		1.3.6.1.4.1.644.2.4.2.2.1.1.1.2
Uniquely identifies an HDS3 Port in the system. This number is provided as key to allow the manager to map this entry to a corresponding Resource Table entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hds3PortCfgName		1.3.6.1.4.1.644.2.4.2.2.1.1.1.3
This is the user friendly text name to identify the circuit.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

hds3FacilityId		1.3.6.1.4.1.644.2.4.2.2.1.1.1.4
This is a description of the facility where this equipment is located.
Status: obsolete	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..37)

hds3EquipmentId		1.3.6.1.4.1.644.2.4.2.2.1.1.1.5
This is a description of the equipment in use.
Status: obsolete	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..9)

hds3Location		1.3.6.1.4.1.644.2.4.2.2.1.1.1.6
This is the user description of the location for this equipment.
Status: obsolete	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

hds3FrameId		1.3.6.1.4.1.644.2.4.2.2.1.1.1.7
This is the description of the building where this equipment is located.
Status: obsolete	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..9)

hds3UnitName		1.3.6.1.4.1.644.2.4.2.2.1.1.1.8
This is the description of the bay or device this equipment is part of.
Status: obsolete	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..5)

hds3PortNumber		1.3.6.1.4.1.644.2.4.2.2.1.1.1.9
This is the user description of the HDS-3 port.
Status: obsolete	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..37)

hds3Generator		1.3.6.1.4.1.644.2.4.2.2.1.1.1.10
This is the user description of the number generated by this equipment.
Status: obsolete	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..37)

hds3M13OpMode		1.3.6.1.4.1.644.2.4.2.2.1.1.1.11
The framing selection for the DS1 to HDS-3 multiplexing.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	bellcoreM13(0), c-bitParity(1)

hds3RcvLoopTiming		1.3.6.1.4.1.644.2.4.2.2.1.1.1.12
Enables or disables the HDS-3 transmit timing provided by the receive clock. When disabled, timing is provided by an on-board oscillator.
Status: current	Access: read-write
OBJECT-TYPE
	FunctionSwitch

hds3ShortCable		1.3.6.1.4.1.644.2.4.2.2.1.1.1.13
Indicates the line build out of the HDS-3 transmitter. 'Yes' when attached to a cable less than 50 feet long.
Status: current	Access: read-write
OBJECT-TYPE
	DecisionType

hds3M13RemLoop		1.3.6.1.4.1.644.2.4.2.2.1.1.1.14
Controls line codes used to set and reset DS3 remote line loopback requests. This setting is provided by the carrier. These codes cause a DS3 loopback in remote DS3 equipment or respond to codes from remote DS3 equipment. This applies to Bellcore M13 mode only. Different manufacturers use different patterns in M13 mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	third-cbit-inverted(0), second-cbit-inverted(1), first-cbit-inverted(2)

hds3FEACLoopbackReq		1.3.6.1.4.1.644.2.4.2.2.1.1.1.15
Select enabled(1) to allow the module to respond to a Far End Alarm and Control loopback request.
Status: current	Access: read-write
OBJECT-TYPE
	FunctionSwitch

hds3XmtAISLocalLoop		1.3.6.1.4.1.644.2.4.2.2.1.1.1.16
The Transmitted bit pattern used when the HDS3 port is in Local Loop.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), framed-1010-cbitZero(1), framed-allones-cbitZero(2), unframed-allones(3)

hds3RcvAIS		1.3.6.1.4.1.644.2.4.2.2.1.1.1.17
The Received bit pattern to use to determine when the remote line is in error.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	framed1010-noOverheadBits(1), cbitZero-noPayloadBits(2), framed1010-cbitZero(3), framed1111-noOverheadBits(4), unframed-allones(5)

hds3XmtAIS		1.3.6.1.4.1.644.2.4.2.2.1.1.1.18
The Transmitted bit pattern that used when the HDS3 port is in error.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), framed-1010-cbitZero(1), framed-allones-cbitZero(2), unframed-allones(3)

hds3DS2Group1		1.3.6.1.4.1.644.2.4.2.2.1.1.1.19
Indicates the type of grouping option used to on links 1 through 4. Using the VT 2.0, link 4 is not used.
Status: current	Access: read-write
OBJECT-TYPE
	DS2GroupType

hds3DS2Group2		1.3.6.1.4.1.644.2.4.2.2.1.1.1.20
Indicates the type of grouping option used to on links 5 through 8. Using the VT 2.0, link 8 is not used.
Status: current	Access: read-write
OBJECT-TYPE
	DS2GroupType

hds3DS2Group3		1.3.6.1.4.1.644.2.4.2.2.1.1.1.21
Indicates the type of grouping option used to on links 9 through 12. Using the VT 2.0, link 12 is not used.
Status: current	Access: read-write
OBJECT-TYPE
	DS2GroupType

hds3DS2Group4		1.3.6.1.4.1.644.2.4.2.2.1.1.1.22
Indicates the type of grouping option used to on links 13 through 16. Using the VT 2.0, link 16 is not used.
Status: current	Access: read-write
OBJECT-TYPE
	DS2GroupType

hds3DS2Group5		1.3.6.1.4.1.644.2.4.2.2.1.1.1.23
Indicates the type of grouping option used to on links 17 through 20. Using the VT 2.0, link 20 is not used.
Status: current	Access: read-write
OBJECT-TYPE
	DS2GroupType

hds3DS2Group6		1.3.6.1.4.1.644.2.4.2.2.1.1.1.24
Indicates the type of grouping option used to on links 21 through 24. Using the VT 2.0, link 24 is not used.
Status: current	Access: read-write
OBJECT-TYPE
	DS2GroupType

hds3DS2Group7		1.3.6.1.4.1.644.2.4.2.2.1.1.1.25
Indicates the type of grouping option used to on links 25 through 28. Using the VT 2.0, link 28 is not used.
Status: current	Access: read-write
OBJECT-TYPE
	DS2GroupType

hds3CmdStatus		1.3.6.1.4.1.644.2.4.2.2.1.1.1.26
The command status for this link configuration row/record. The value used in a SET will be replaced by a response value in the GET RESPONSE indicating success or failure. Default Response State used in GET RESPONSE Command ready-for-command (0) initial default status for a row HDS3 Link Commands used in SET Command (1..199) update-link-config(1), Change existing Link Configuration Response States used in GET RESPONSE Command (200..399) update-successful (201) Link data has been successfully changed HDS3 Port Config Error Codes used in GET RESPONSE Command (400..699) err-general-link-config-error (400) Unknown link configuration error occurred err-invalid-link-status (401) Unrecognized link status setting err-invalid-link-framing (402) Line framing type not valid for link type err-invalid-link-command (403) Unrecognized link command-action err-invalid-link-op-mode (407) Configured M13 Op mode not valid for port; verify other link parameters match desired new mode err-invalid-link-rem-loop (408) Remote Loop type not valid for hds3 frame type err-invalid-link-ais (409) Unrecognized hds3 AIS selection err-data-locked-by-another-user (450) Another administrative user is making changes to this part of the system via a terminal session. Check Event Log for user name.
Status: current	Access: read-write
OBJECT-TYPE
	LinkCmdStatus

hds3T1E1LinkConfigTable		1.3.6.1.4.1.644.2.4.2.2.1.2
This is the HDS-3 T-1 Link Configuration table which consists of an entry for each of the card's 28 links. The total number of entries depends on the number of HDS3 cards in the nest.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HDS3T1E1LinkConfigEntry

hds3T1E1LinkConfigEntry		1.3.6.1.4.1.644.2.4.2.2.1.2.1
The conceptual row of the HDS-3 T-1 Link Configuration table. A row in this table cannot be added or deleted, only modified.
Status: current	Access: not-accessible
OBJECT-TYPE
	HDS3T1E1LinkConfigEntry

hds3T1E1CfgLinkAddr		1.3.6.1.4.1.644.2.4.2.2.1.2.1.1
This number uniquely identifies a HDS-3 T1/E1 link resource. This number will be used throughout the system to identify a unique resource.
Status: current	Access: read-only
OBJECT-TYPE
	LinkPortAddress

hds3T1E1CfgResource		1.3.6.1.4.1.644.2.4.2.2.1.2.1.2
Uniquely identifies an HDS-3 T1/E1 Channel in the system. This number is provided as key to allow the manager to map this entry to a corresponding Resource Table entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hds3T1E1CfgLinkName		1.3.6.1.4.1.644.2.4.2.2.1.2.1.3
This is the user friendly text name to identify the link.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

hds3T1E1Status		1.3.6.1.4.1.644.2.4.2.2.1.2.1.4
Dictates the current status of the link, in-service or out-of-service.
Status: current	Access: read-write
OBJECT-TYPE
	PortStatus

hds3T1E1Clear		1.3.6.1.4.1.644.2.4.2.2.1.2.1.5
Determines if the port supports T1 or E1 unframed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(0), framed(1), unframed(2)

hds3T1E1Framing		1.3.6.1.4.1.644.2.4.2.2.1.2.1.6
Determines the type of framing used on the line. Choose between T1 SuperFrame 'D4', Extended SuperFrame (ESF), or T1 Unframed. When value of hds3T1E1Clear is set to unframed (2), the only valid framing options are: e1Unframed(4) or t1Unframed(7).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	e1(0), e1Crc(1), e1Cas(2), e1CasCrc(3), e1Unframed(4), t1Esf(5), t1D4(6), t1Unframed(7)

hds3T1E1NetLoop		1.3.6.1.4.1.644.2.4.2.2.1.2.1.7
Determines whether or not the module should respond to loop diagnostic commands received from the network supplier. Select 'enable' unless the commands are to be passed to another HDS3 device.
Status: current	Access: read-write
OBJECT-TYPE
	FunctionSwitch

hds3T1E1YelAlrm		1.3.6.1.4.1.644.2.4.2.2.1.2.1.8
Causes the module to discard data and send a yellow alarm if it is in a red alarm condition after a 3 second period. 'Yes' must be chosen if the network supplier is a common carrier, such as a telephone company.
Status: current	Access: read-write
OBJECT-TYPE
	DecisionType

hds3T1E1RecoverTime		1.3.6.1.4.1.644.2.4.2.2.1.2.1.9
This is the red alarm timeout value. Determines the amount of seconds the port will wait to stop sending the yellow alarm when coming out of a red alarm condition. This field does not apply to E1 links.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	timeout-3-secs(3), timeout-10-secs(10), timeout-15-secs(15)

hds3T1E1EsfFormat		1.3.6.1.4.1.644.2.4.2.2.1.2.1.10
Determines the type of ESF network commands the T-1 link will respond to. It has no meaning for D4 networks. With ESF networks, this information must be obtained from the network supplier.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	att-54016(0), ansi-t1-403(1)

hds3T1E1IdleCode		1.3.6.1.4.1.644.2.4.2.2.1.2.1.11
Determines the whether the code that will be transmitted over the unused links will be 'idle' or 'busy' (all 1's).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	busy(0), idle(1)

hds3T1E1CfgCmdStatus		1.3.6.1.4.1.644.2.4.2.2.1.2.1.12
The command status for this link configuration row/record. The value used in a SET will be replaced by a response value in the GET RESPONSE indicating success or failure. Default Response State used in GET RESPONSE Command ready-for-command (0) initial default status for a row HDS3-T1E1 Link Commands used in SET Command (1..199) update(1) Change existing Link Configuration inServiceAll (7) Change Link Status to in-service for all 8 links. copyToAll (9) Copy T1 Link configuration to all other links within the same device outOfServiceAll (12) Change Link Status to out-of-service for all 8 links. Response States used in GET RESPONSE Command (100..199) update-successful (101) Link data has been successfully changed insvc-successful (107) All Links have been successfully placed In Service copy-successful (109) T1 Link data has been successfully copied to other links oos-successful (112) All Links have been successfully placed Out of Service HDS3-T1E1 Link Config Error Codes used in GET RESPONSE Command (400..699) err-general-link-config-error (400) Unknown link configuration error occurred err-invalid-link-status (401) Unrecognized link status setting err-invalid-link-framing (402) Line framing type not valid for link type err-invalid-link-command (403) Unrecognized link command-action err-invalid-esf-format (405) ESF type not applicable to link type err-invalid-link-density (406) Unrecognized T1 link density setting err-invalid-network-loop (410) Unrecognized network loop setting err-invalid-yellow-alrm (411) Unrecognized yellow alarm setting err-invalid-red-timeout (412) Unrecognized red alarm timeout err-invalid-idle-code (413) Unrecognized idle code err-device-in-standby (414) Can't change config for designated Standby device err-invalid-link-bits (427) Reserved E1 bits must be left at zero. err-data-locked-by-another-user (450) Another administrative user is making changes to this part of the system via a terminal session. Check Event Log for user name err-snmp-parse-failed (500) Agent could not parse variable err-invalid-snmp-type (501) Variable ASN type does not match Agent defined type err-invalid-snmp-var-size (502) Variable size is too big
Status: current	Access: read-write
OBJECT-TYPE
	LinkCmdStatus

hds3T1E1Gr303Facility		1.3.6.1.4.1.644.2.4.2.2.1.2.1.13
Enables link to be configured as a Gr303 Facility
Status: obsolete	Access: read-only
OBJECT-TYPE
	DecisionType

hds3T1E1NationalBits		1.3.6.1.4.1.644.2.4.2.2.1.2.1.14
Enables E1 National S-bits to be set to zero or one. This single byte field can be changed to set the values of the E1 NFA byte in odd frames as depicted below: sa8 sa7 sa6 sa5 sa4 reserved bits --- --- --- --- --- ------------- 1 1 1 1 1 0 0 0 = F8 (default) Values should be entered in Hex. If reserved bits are changed, an error code (427) will be returned in the command status.
Status: current	Access: read-write
OBJECT-TYPE
	OneByteField

hds3T1E1InterNational		1.3.6.1.4.1.644.2.4.2.2.1.2.1.15
Enables InterNational S(i) Spare bit to be set to zero or one. This single byte field can be changed to set the values of the Bit 1 of TS0 G.704 frame as depicted below: reserved bits S(i) -------------------------- ----- 0 0 0 0 0 0 0 1 = 01 (default) Values should be entered in Hex. If reserved bits are changed, an error code (427) will be returned in the command status.
Status: current	Access: read-write
OBJECT-TYPE
	OneByteField

hds3FramerStatusTable		1.3.6.1.4.1.644.2.4.2.2.2.1
This is the HDS-3 Framer Status table which consists of a single entry for each card's Framer Display. The total number of entries depends on the number of HDS3 cards in the nest.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HDS3FramerStatusEntry

hds3FramerStatusEntry		1.3.6.1.4.1.644.2.4.2.2.2.1.1
The conceptual row of the Framer table. A row in this table cannot be added or deleted, only modified.
Status: current	Access: not-accessible
OBJECT-TYPE
	HDS3FramerStatusEntry

hds3FramerStatusAddr		1.3.6.1.4.1.644.2.4.2.2.2.1.1.1
This number uniquely identifies a HDS-3 Framer resource. This number will be used throughout the system to identify a unique resource.
Status: current	Access: read-only
OBJECT-TYPE
	LinkPortAddress

hds3FramerStatusResource		1.3.6.1.4.1.644.2.4.2.2.2.1.1.2
This number uniquely identifies a HDS-3 Framer link resource. This number is provided as key to allow the manager to map this entry to a corresponding Resource Table Entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hds3FramerStatusState		1.3.6.1.4.1.644.2.4.2.2.2.1.1.3
Determines the current line condition status of the Framer. ok (0) - No Alarm ais (8) - Sending All Ones lof (32) - Loss/Out of Frame los (64) - Loss of Signal errors (2147483647) - Multiple Errors displays raw bit field value
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ok(0), ais(8), lof(32), los(64), errors(2147483647)

hds3FramerStatusRedAlrmErrSecs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.4
This is the number of seconds a Red Alarm condition was declared. Declared when out of frame condition persists for more than 13.5msec.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusLOSErrSecs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.5
This is the number of seconds a Loss of Signal condition was declared. Loss of signal declared after receipt of 175 contiguous zeroes.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusOOFErrSecs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.6
This is the number of seconds Frame alignment errors were detected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusAISErrSecs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.7
This is the number of seconds a Alarm Indication Signal condition was declared. Declared after optioned AIS pattern is detected for more than 13.5msec.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusRcvIdleErrSecs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.8
This is the number of seconds a Receive Idle Pattern condition was declared. Declared when DS3 1100 idle pattern detected for more than 13.5ms.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusFarEndRcvErrSecs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.9
This is the number of seconds a Far End Receive Failure condition was declared. Declared when both X-bits set to 0 in M13 and C-bit Parity frame format (i.e., yellow alarm indicator)
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusCFAErrSecs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.10
This is the number of seconds a Frame alignment change was detected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusTotErrSecs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.11
Total number of seconds in which any of the errored events have occurred.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusPbitParityErrs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.12
The number of P-bit Parity errors detected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusCbitParityErrs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.13
The number of C-bit Parity errors detected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusFebeErrs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.14
The number of Far End Block errors detected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusLCVErrs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.15
The number of Line Code Violation errors detected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusFramingErrs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.16
The number of Framing errors detected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusExcessZeroErrs		1.3.6.1.4.1.644.2.4.2.2.2.1.1.17
The number of Excessive Zero errors detected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3FramerStatusInsErrMode		1.3.6.1.4.1.644.2.4.2.2.2.1.1.18
Determines the status of the current Insert Error mode associated with the framer. In order to insert an error, the hds3FramerStatusCmdStatus must be sent in a SET PDU with a value of 'insertError'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	febe(1), p-bit-parity(2), c-bit-parity(3), multiframe-align(4), frame-alignment(5), allErrors(8)

hds3FramerStatusCmdStatus		1.3.6.1.4.1.644.2.4.2.2.2.1.1.19
This is the command status for the DS3 Framer Row. The value used in a SET will be replaced by a response value in the GET RESPONSE indicating success or failure. Default Response State used in GET RESPONSE Command ready-for-command (0) initial default status for a row DS3 Framer Action Commands used in SET Command (1..99) update (1) Can be used optionally when inserting errors in order to get status code back in response clearErrors (14) Resets all error counters and bert test time to zero insertError (16) Inserts the current invalid bit pattern as indicated by the value of hds3FramerStatusInsErrMode. Response States used in GET RESPONSE Command (100..199) update-successful (101) Action has been successfully performed clear-successful (114) Error counts have been successfully cleared insert-successful (116) Errored bits have been successfully inserted The Error Codes used in GET RESPONSE Command (200..799) err-general-framer-error (200) Unknown request error occurred. err-test-in-progress (205) Requested action cannot be performed during bert err-field-cannot-be-set (206) Read-only field was included in SET request err-invalid-command (208) Unrecognized framer Command requested err-snmp-parse-failed (500) Agent could not parse variable err-invalid-snmp-type (501) Variable ASN type does not match Agent defined type err-invalid-snmp-var-size (502) Variable size is too big
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ready-for-command(0), update(1), clearErrors(14), insertError(16), update-successful(101), clear-successful(114), insert-successful(116), err-general-framer-error(200), err-test-in-progress(205), err-field-cannot-be-set(206), err-invalid-command(208), err-snmp-parse-failed(500), err-invalid-snmp-type(501), err-invalid-snmp-var-size(502)

hds3LIUTable		1.3.6.1.4.1.644.2.4.2.2.2.2
This is the HDS-3 LIU Diagnostic Status Display table which consists of an entry for each HDS3 card's Line Interface Unit Display. The number of entries depends on the number of HDS3 cards in the nest.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HDS3LIUEntry

hds3LIUEntry		1.3.6.1.4.1.644.2.4.2.2.2.2.1
The conceptual row of the HDS3 LIU table. A row in this table cannot be added or deleted, only modified.
Status: current	Access: not-accessible
OBJECT-TYPE
	HDS3LIUEntry

hds3LIUAddr		1.3.6.1.4.1.644.2.4.2.2.2.2.1.1
This number uniquely identifies a HDS-3 LIU resource address. This number will be used throughout the system to identify a unique resource.
Status: current	Access: read-only
OBJECT-TYPE
	LinkPortAddress

hds3LIUResource		1.3.6.1.4.1.644.2.4.2.2.2.2.1.2
This number uniquely identifies a HDS-3 LIU resource. This number is provided as a key to allow the manager to map this entry to a corresponding Resource Table Entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hds3LIUBertState		1.3.6.1.4.1.644.2.4.2.2.2.2.1.3
This is the LIU Bert State indicated by liu-bert(on)/off. The LIU Bert is an 2^15-1 Unframed BERT.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	liu-bert(44), off(45)

hds3LIUBertErrSecs		1.3.6.1.4.1.644.2.4.2.2.2.2.1.4
This is the number of LIU Bert Errored seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3LIUBertDuration		1.3.6.1.4.1.644.2.4.2.2.2.2.1.5
This is the number of seconds for the LIU Bert Duration.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3LIULoopType		1.3.6.1.4.1.644.2.4.2.2.2.2.1.6
Indicates the loopback status of the DS3 Framer/LIU for this device. off (0) - indicates loopback is disabled ds3-local (1) - indicates DS3 local data is looped back to itself ds3-line (36)- entire DS3 Frame is looped, framing is not regenerated liu (39)- indicates Line Interface Unit local data is looped back to itself.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(0), ds3-local(1), ds3-line(36), liu(39)

hds3LIUDigitalErrs		1.3.6.1.4.1.644.2.4.2.2.2.2.1.7
This is the number of seconds recorded for the LIU Digital Errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3LIUAnalogErrs		1.3.6.1.4.1.644.2.4.2.2.2.2.1.8
This is the number of seconds recorded for the LIU Analog Errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3LIUExcessZeroErrs		1.3.6.1.4.1.644.2.4.2.2.2.2.1.9
This is the number of seconds LIU Excess zero errors were detected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3LIUCodingViolationErrs		1.3.6.1.4.1.644.2.4.2.2.2.2.1.10
This is the total number of Errored Seconds for the LIU Coding Violation.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3LIUPRBSCheckErrs		1.3.6.1.4.1.644.2.4.2.2.2.2.1.11
This is the total number of Errored Seconds for the LIU PRBS check.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hds3LIUCmdStatus		1.3.6.1.4.1.644.2.4.2.2.2.2.1.12
This is the command status for the LIU Framer Row. The value used in a SET will be replaced by a response value in the GET RESPONSE indicating success or failure. Default Response State used in GET RESPONSE Command ready-for-command (0) initial default status for a row Commands used in SET Command (1..99) update (1) Can be used optionally when activating loops and berts in order to get status code back in response clearErrors (14) Resets all error counters and bert test time to zero Response States used in GET RESPONSE Command (100..199) update-successful (101) Test action has been successfully performed clear-successful (114) Error counts have been successfully cleared Error Codes used in GET RESPONSE Command (200..799) err-general-liu-error (200) Unknown LIU request error occurred. err-invalid-loop-type (202) Unrecognized loop selection err-invalid-bert-type (203) Unrecognized bert selection err-test-in-progress (205) Requested action cannot be performed during bert err-field-cannot-be-set (206) Read-only field was included in SET request err-invalid-command (208) Unrecognized Test Command requested err-snmp-parse-failed (500) Agent could not parse variable err-invalid-snmp-type (501) Variable ASN type does not match Agent defined type err-invalid-snmp-var-size (502) Variable size is too big
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ready-for-command(0), update(1), clearErrors(14), update-successful(101), clear-successful(114), err-general-liu-error(200), err-invalid-loop-type(202), err-invalid-bert-type(203), err-test-in-progress(205), err-field-cannot-be-set(206), err-invalid-command(208), err-snmp-parse-failed(500), err-invalid-snmp-type(501), err-invalid-snmp-var-size(502)

dnxHDS3Enterprise		1.3.6.1.4.1.644.2.4.2.2.0
ERI DNX HDS3 Enterprise for Alarms/Events
Status: current	Access: read-write
OBJECT-IDENTITY

hds3PortConfigTrap		1.3.6.1.4.1.644.2.4.2.2.0.1
This trap is used to notify a NMS that a user has updated the configuration for a given HDS3 Port entry.
Status: current	Access: read-write
NOTIFICATION-TYPE

hds3T1E1ConfigTrap		1.3.6.1.4.1.644.2.4.2.2.0.2
This trap is used to notify a NMS that a user has updated the Link configuration for a given HDS3-T1/E1 channel entry.
Status: current	Access: read-write
NOTIFICATION-TYPE