ENTERASYS-IEEE802DOT11EXT-MIB

File: ENTERASYS-IEEE802DOT11EXT-MIB.mib (27913 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
SNMP-FRAMEWORK-MIB IF-MIB P-BRIDGE-MIB
IEEE802dot11-MIB ENTERASYS-MIB-NAMES

Imported symbols

MODULE-IDENTITY OBJECT-TYPE TEXTUAL-CONVENTION
TruthValue MacAddress AutonomousType
MODULE-COMPLIANCE OBJECT-GROUP SnmpAdminString
ifIndex EnabledStatus dot11WEPDefaultKeyIndex
etsysModules

Defined Types

EtsysDot11ExtLinkTestEntry  
SEQUENCE    
  etsysDot11ExtLTRemoteStationMAC MacAddress
  etsysDot11ExtLTRemoteStationName SnmpAdminString
  etsysDot11ExtLTTrigger INTEGER
  etsysDot11ExtLTRemoteContents OCTET STRING

EtsysDot11ExtGeneralEntry  
SEQUENCE    
  etsysDot11ExtPCCardType INTEGER
  etsysDot11ExtPCCardVersions SnmpAdminString
  etsysDot11ExtBridgeMode INTEGER
  etsysDot11ExtResetOptions INTEGER
  etsysDot11ExtSystemScale INTEGER
  etsysDot11ExtSecureAccess EnabledStatus
  etsysDot11ExtMulticastTxRate INTEGER
  etsysDot11ExtIntraBSSRelay EnabledStatus
  etsysDot11ExtStationName SnmpAdminString

EtsysDot11ExtBldgEntry  
SEQUENCE    
  etsysDot11ExtBldgRemoteMAC1 MacAddress
  etsysDot11ExtBldgRemoteMAC2 MacAddress
  etsysDot11ExtBldgRemoteMAC3 MacAddress
  etsysDot11ExtBldgRemoteMAC4 MacAddress
  etsysDot11ExtBldgRemoteMAC5 MacAddress
  etsysDot11ExtBldgRemoteMAC6 MacAddress
  etsysDot11ExtBldgMPActivationKey OCTET STRING

EtsysDot11ExtWEPDefaultKeysEntry  
SEQUENCE    
  etsysDot11ExtWEPKeyDefined TruthValue
  etsysDot11ExtWEPKeyValue OCTET STRING

EtsysDot11ExtWEPEnhancedEntry  
SEQUENCE    
  etsysDot11ExtWEPEnhancedImplemented TruthValue

EtsysDot11ExtOIDNotInEffectEntry  
SEQUENCE    
  etsysDot11ExtOIDIndex AutonomousType
  etsysDot11ExtOIDNotInEffect TruthValue

Defined Values

etsysDot11ExtMIB 1.3.6.1.4.1.5624.1.2.9
This mib module defines a portion of the SNMP enterprise MIBs under Enterasys Networks enterprise OID as an extension to the IEEE802Dot11 MIB. This Enterasys Networks Proprietary MIB was designed to be used for read-write access to configuration objects not provided by IEEE802.11 MIB, or any other standard MIB.
MODULE-IDENTITY    

etsysDot11ExtObjects 1.3.6.1.4.1.5624.1.2.9.1
OBJECT IDENTIFIER    

etsysDot11ExtLinkTest 1.3.6.1.4.1.5624.1.2.9.1.1
OBJECT IDENTIFIER    

etsysDot11ExtGeneral 1.3.6.1.4.1.5624.1.2.9.1.2
OBJECT IDENTIFIER    

etsysDot11ExtBldg 1.3.6.1.4.1.5624.1.2.9.1.3
OBJECT IDENTIFIER    

etsysDot11ExtWEP 1.3.6.1.4.1.5624.1.2.9.1.4
OBJECT IDENTIFIER    

etsysDot11ExtEffect 1.3.6.1.4.1.5624.1.2.9.1.5
OBJECT IDENTIFIER    

etsysDot11ExtLinkTestTable 1.3.6.1.4.1.5624.1.2.9.1.1.1
This table contains objects to test the link between a requester (entity which sends out the management request message) and a responder (entity which responds with the appropriate management response message). An entity could be either an Access Point(AP) or a station (STA).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysDot11ExtLinkTestEntry

etsysDot11ExtLinkTestEntry 1.3.6.1.4.1.5624.1.2.9.1.1.1.1
An Entry (conceptual row) in the LinkTest Table. By means of message transmission between requester and responder, the communication quality between the two stations can be determined. The requester and responder can be any combination of AP and STA except STA to STA in an Infrastructure Network (network which has at least one AP present.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysDot11ExtLinkTestEntry  

etsysDot11ExtLTRemoteStationMAC 1.3.6.1.4.1.5624.1.2.9.1.1.1.1.1
The MAC address for the remote station to participate in the Link Test. To initiate a search for a participating station, write the broadcast address (FF-FF-FF-FF-FF-FF) to this variable.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

etsysDot11ExtLTRemoteStationName 1.3.6.1.4.1.5624.1.2.9.1.1.1.1.2
The wireless station name of the remote station participating in the Link Test.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..20)  

etsysDot11ExtLTTrigger 1.3.6.1.4.1.5624.1.2.9.1.1.1.1.3
Writing a 1 to this variable causes a single Link Test request message to be sent to the remote station.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1  

etsysDot11ExtLTRemoteContents 1.3.6.1.4.1.5624.1.2.9.1.1.1.1.4
The exact byte-by-byte contents of the Link Test packet returned by the remote station.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(84)  

etsysDot11ExtGeneralTable 1.3.6.1.4.1.5624.1.2.9.1.2.1
This table contains all the objects that must be configured on every radio card installed in the Access Point regardless of the operating mode in use.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysDot11ExtGeneralEntry

etsysDot11ExtGeneralEntry 1.3.6.1.4.1.5624.1.2.9.1.2.1.1
An Entry (conceptual row) in the Dot11General Table. This allows for multiple instances of radio cards in the Access Point.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysDot11ExtGeneralEntry  

etsysDot11ExtPCCardType 1.3.6.1.4.1.5624.1.2.9.1.2.1.1.1
The type of PC card inserted in the Access Point.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), deprecatedValue1(2), deprecatedValue2(3), deprecatedValue3(4), ds80211b(5), ds80211a(6), unknown(15)  

etsysDot11ExtPCCardVersions 1.3.6.1.4.1.5624.1.2.9.1.2.1.1.2
Specifies the version identifiers for the PC card. This will indicate both the Hardware and the Firmware versions.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(1..80)  

etsysDot11ExtBridgeMode 1.3.6.1.4.1.5624.1.2.9.1.2.1.1.3
CURRENT Access Point bridge mode state. In workgroup mode all communications between clients passes through the Access Point. LAN-to-LAN mode is the improved name for 802.11. LAN-to-LAN used to be called full-bridge pre-802.11. This mode is a method of connecting two wired LAN's via a wireless link, also referred to as Point-to-Point mode. LAN-to-LAN-HUB mode allows the interconnection of multiple (ie. more than two) wired LAN's via wireless links, also referred to as Point-to-MultiPoint mode. When operating in multimode the Access Point can simultaneously operate in both workgroup mode and either Point-to-Point or Point-to-MultiPoint modes. This object must be saved across a system reset and/or a power cycle.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER workgroup(1), lanToLanEndpoint(2), lanToLanMultipoint(3)  

etsysDot11ExtResetOptions 1.3.6.1.4.1.5624.1.2.9.1.2.1.1.4
noReset (0) No reset is performed. A 'get' on this object always returns this value. resetRadioCardIfNecessary (1) Some parameters can only be given to the card at initialization time, and if any of these are changed, a card reset will be necessary for them to go into place. The card will be reset at this time if any of those parameters have indeed been changed. resetRadioCardRegardless (2) Forces the radio card to reset, even if no radio card parameters have been changed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noReset(0), resetRadioCardIfNecessary(1), resetRadioCardRegardless(2)  

etsysDot11ExtSystemScale 1.3.6.1.4.1.5624.1.2.9.1.2.1.1.5
Specifies the CURRENT Access Point density in the Extended Service Set (ESS). This object must be saved across a system reset and/or a power cycle.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER low(1), medium(2), high(3)  

etsysDot11ExtSecureAccess 1.3.6.1.4.1.5624.1.2.9.1.2.1.1.6
When this mode is set to enabled, the AP will only associate with stations that have the same network name as the AP. When this mode is set to disabled, a station with the network name of ANY is allowed to associate. This object must be saved across a system reset and/or a power cycle.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

etsysDot11ExtMulticastTxRate 1.3.6.1.4.1.5624.1.2.9.1.2.1.1.7
This value specifies the Multicast data transmission rate of the AP. It is implemented when cards that operate faster than the 2Mbit 802.11 standard are inserted. This object must be saved across a system reset and/or a power cycle.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fixed1Mbit(1), fixed2Mbit(2), fixedMediumRate(3), fixedHighRate(4)  

etsysDot11ExtIntraBSSRelay 1.3.6.1.4.1.5624.1.2.9.1.2.1.1.8
When this mode is enabled the AP entity within the PC Card will relay frames to destined for stations associated with it and will NOT forward them to the bridging entity within the AP. When this mode is set to disabled, the AP entity within the PC Card will not relay frames from wireless client(s) to station(s) associated with it, instead forwards frames to the bridging entity within the AP. This object must be saved across a system reset and/or a power cycle.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

etsysDot11ExtStationName 1.3.6.1.4.1.5624.1.2.9.1.2.1.1.9
DURABLE: The wireless station name sent out as part of the beacon messages. Valid only when a DS card is inserted in the Access Point.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..20)  

etsysDot11ExtBldgTable 1.3.6.1.4.1.5624.1.2.9.1.3.1
This table contains the objects required to enable the Access Point to operate in Point-to-MultiPoint mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysDot11ExtBldgEntry

etsysDot11ExtBldgEntry 1.3.6.1.4.1.5624.1.2.9.1.3.1.1
An Entry (conceptual row) in the Dot11Bldg Table. A collection of objects containing information for activating and using the Access Point in Point-to-MultiPoint mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysDot11ExtBldgEntry  

etsysDot11ExtBldgRemoteMAC1 1.3.6.1.4.1.5624.1.2.9.1.3.1.1.1
The MAC address for the remote station participating in a 802.11 Building-to-Building link. This object must be saved across a system reset and/or a power cycle.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

etsysDot11ExtBldgRemoteMAC2 1.3.6.1.4.1.5624.1.2.9.1.3.1.1.2
The MAC address for the remote station participating in a 802.11 Building-to-Building link. This object must be saved across a system reset and/or a power cycle.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

etsysDot11ExtBldgRemoteMAC3 1.3.6.1.4.1.5624.1.2.9.1.3.1.1.3
The MAC address for the remote station participating in a 802.11 Building-to-Building link. This object must be saved across a system reset and/or a power cycle.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

etsysDot11ExtBldgRemoteMAC4 1.3.6.1.4.1.5624.1.2.9.1.3.1.1.4
The MAC address for the remote station participating in a 802.11 Building-to-Building link. This object must be saved across a system reset and/or a power cycle.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

etsysDot11ExtBldgRemoteMAC5 1.3.6.1.4.1.5624.1.2.9.1.3.1.1.5
The MAC address for the remote station participating in a 802.11 Building-to-Building link. This object must be saved across a system reset and/or a power cycle.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

etsysDot11ExtBldgRemoteMAC6 1.3.6.1.4.1.5624.1.2.9.1.3.1.1.6
The MAC address for the remote station participating in a 802.11 Building-to-Building link. This object must be saved across a system reset and/or a power cycle.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

etsysDot11ExtBldgMPActivationKey 1.3.6.1.4.1.5624.1.2.9.1.3.1.1.7
Point-to-multipoint bridge mode requires an activation key to enable. A valid multipoint activation key must be entered as a string of ACSCII characters translating to the binary HEX value of the key before the Access Point will accept the point-to-multipoint bridge mode setting. Returns SNMP_BAD_VALUE if validation fails. This object must be saved across a system reset and/or a power cycle.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(16)  

etsysDot11ExtWEPDefaultKeysTable 1.3.6.1.4.1.5624.1.2.9.1.4.1
Conceptual table for WEP default keys. This table shall contain the four WEP default secret key values corresponding to the four possible KeyID values. The WEP default secret keys are logically WRITE-ONLY. Attempts to read the entries in this table shall return unsuccessful status and a value of null. The default value of each WEP default key shall be null.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysDot11ExtWEPDefaultKeysEntry

etsysDot11ExtWEPDefaultKeysEntry 1.3.6.1.4.1.5624.1.2.9.1.4.1.1
An Entry (conceptual row) in the WEP Default Keys Table. A collection of objects containing information used to determine if a WEPkey as been defined and if so, the value of the WEPkey.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysDot11ExtWEPDefaultKeysEntry  

etsysDot11ExtWEPKeyDefined 1.3.6.1.4.1.5624.1.2.9.1.4.1.1.1
The state column used for determining if an encryption key is set (true) or not (false), false is the default value.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

etsysDot11ExtWEPKeyValue 1.3.6.1.4.1.5624.1.2.9.1.4.1.1.2
A WEP default secret key value. For 40-bit encryption use 5 printable characters or 10 HEX digits. For 128-bit encryption use 13 printable characters or 26 HEX digits. This object must be saved across a system reset and/or a power cycle.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(5|13)  

etsysDot11ExtWEPEnhancedTable 1.3.6.1.4.1.5624.1.2.9.1.4.2
Conceptual table for WEP default keys. This table shall contain the four WEP default secret key values corresponding to the four possible KeyID values. The WEP default secret keys are logically WRITE-ONLY. Attempts to read the entries in this table shall return unsuccessful status and a value of null. The default value of each WEP default key shall be null.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysDot11ExtWEPEnhancedEntry

etsysDot11ExtWEPEnhancedEntry 1.3.6.1.4.1.5624.1.2.9.1.4.2.1
An Entry (conceptual row) in the WEP Default Keys Table. A collection of objects containing information used to determine if a WEPkey as been defined and if so, the value of the WEPkey.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysDot11ExtWEPEnhancedEntry  

etsysDot11ExtWEPEnhancedImplemented 1.3.6.1.4.1.5624.1.2.9.1.4.2.1.1
This value indicates whether the AP is capable of Enhanced Wireless Equivalent Privacy (WEP), using 128-bit keys.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

etsysDot11ExtOIDNotInEffectTable 1.3.6.1.4.1.5624.1.2.9.1.5.1
This table will be used to determine which wireless parameters have been modified but are not yet in effect. These parameters will not take effect until a reset has been performed.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysDot11ExtOIDNotInEffectEntry

etsysDot11ExtOIDNotInEffectEntry 1.3.6.1.4.1.5624.1.2.9.1.5.1.1
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysDot11ExtOIDNotInEffectEntry  

etsysDot11ExtOIDIndex 1.3.6.1.4.1.5624.1.2.9.1.5.1.1.1
This object will keep a list of OIDS
Status: current Access: not-accessible
OBJECT-TYPE    
  AutonomousType  

etsysDot11ExtOIDNotInEffect 1.3.6.1.4.1.5624.1.2.9.1.5.1.1.2
This object specifies if the OID being accesed currently has been changed but is not in effect.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

etsysDot11ExtConformance 1.3.6.1.4.1.5624.1.2.9.2
OBJECT IDENTIFIER    

etsysDot11ExtGroups 1.3.6.1.4.1.5624.1.2.9.2.1
OBJECT IDENTIFIER    

etsysDot11ExtCompliances 1.3.6.1.4.1.5624.1.2.9.2.2
OBJECT IDENTIFIER    

etsysDot11ExtBaseGroup 1.3.6.1.4.1.5624.1.2.9.2.1.1
The basic etsysDot11Ext stuff.
Status: current Access: read-only
OBJECT-GROUP    

etsysDot11ExtCompliance 1.3.6.1.4.1.5624.1.2.9.2.2.1
The compliance statement for devices that support 802Dot11 extensions.
Status: current Access: read-only
MODULE-COMPLIANCE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor