ENTERASYS-CONVERGENCE-END-POINT-MIB

File: ENTERASYS-CONVERGENCE-END-POINT-MIB.mib (44221 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB INET-ADDRESS-MIB P-BRIDGE-MIB
SNMP-FRAMEWORK-MIB ENTERASYS-MIB-NAMES

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
TEXTUAL-CONVENTION RowStatus MacAddress
DateAndTime TruthValue MODULE-COMPLIANCE
OBJECT-GROUP ifIndex InterfaceIndex
InetAddressType InetAddress EnabledStatus
SnmpAdminString etsysModules

Defined Types

ConvEndPointTypes  
Supported Convergence End Point products.
TEXTUAL-CONVENTION    
  BITS ciscoIPphone(0), siemensIPphone(1), avayaCLan(2), avayaMedPro(3), genericH323(4), sip(5), lldpMed(6)  

EtsysConvEndPointGlobalConfigEntry  
SEQUENCE    
  etsysConvEndPointGlobalEndPointType ConvEndPointTypes
  etsysConvEndPointGlobalDefaultPolicyIndex Integer32

EtsysConvEndPointProtocolConfigEntry  
SEQUENCE    
  etsysConvEndPointProtocolEndPointType ConvEndPointTypes
  etsysConvEndPointProtocolEnable EnabledStatus

EtsysConvEndPointConnMacEntry  
SEQUENCE    
  etsysConvEndPointConnMacMacAddress MacAddress
  etsysConvEndPointConnMacPortNumber InterfaceIndex
  etsysConvEndPointConnMacEndPointType ConvEndPointTypes
  etsysConvEndPointConnMacPolicyIndex Integer32
  etsysConvEndPointConnMacDiscoveryTime DateAndTime
  etsysConvEndPointConnMacFirmwareVersion SnmpAdminString
  etsysConvEndPointConnMacInetAddressType InetAddressType
  etsysConvEndPointConnMacInetAddress InetAddress

EtsysConvEndPointConnPortEntry  
SEQUENCE    
  etsysConvEndPointConnPortMacAddress MacAddress

EtsysCEPConnMacEntry  
SEQUENCE    
  etsysCEPConnMacEndPointType ConvEndPointTypes
  etsysCEPConnMacPolicyIndex Integer32
  etsysCEPConnMacDiscoveryTime DateAndTime
  etsysCEPConnMacFirmwareVersion SnmpAdminString
  etsysCEPConnMacInetAddressType InetAddressType
  etsysCEPConnMacInetAddress InetAddress

EtsysConvEndPointDetectionEntry  
SEQUENCE    
  etsysConvEndPointDetectionRuleIndex Integer32
  etsysConvEndPointDetectionEndPointType INTEGER
  etsysConvEndPointDetectionProtocol BITS
  etsysConvEndPointDetectionPortLow Integer32
  etsysConvEndPointDetectionPortHigh Integer32
  etsysConvEndPointDetectionAddrType InetAddressType
  etsysConvEndPointDetectionAddr InetAddress
  etsysConvEndPointDetectionAddrMaskType InetAddressType
  etsysConvEndPointDetectionAddrMask InetAddress
  etsysConvEndPointDetectionRowStatus RowStatus

EtsysCEPDetectionPortConfigEntry  
SEQUENCE    
  etsysCEPPortClearUsers TruthValue

EtsysCEPCdpPortConfigEntry  
SEQUENCE    
  etsysCEPCiscoCDPVoicePortVlan Integer32

Defined Values

etsysConvergenceEndPointMIB 1.3.6.1.4.1.5624.1.2.40
This MIB module defines a portion of the SNMP MIB under Enterasys Networks enterprise OID pertaining to Convergence End Point management.
MODULE-IDENTITY    

etsysConvEndPointObjects 1.3.6.1.4.1.5624.1.2.40.1
OBJECT IDENTIFIER    

etsysConvEndPointConfig 1.3.6.1.4.1.5624.1.2.40.1.1
OBJECT IDENTIFIER    

etsysConvEndPointStatus 1.3.6.1.4.1.5624.1.2.40.1.2
OBJECT IDENTIFIER    

etsysConvEndPointDetection 1.3.6.1.4.1.5624.1.2.40.1.3
OBJECT IDENTIFIER    

etsysConvEndPointGlobalConfigEnable 1.3.6.1.4.1.5624.1.2.40.1.1.1
When set to enabled(1) this object activates the current Convergence End Point configuration. When set to disabled(2) this MIB SHALL be configurable, but MUST NOT be applied, all entries will be removed from the etsysConvEndPointConnMacTable and the etsysConvEndPointConnPortTable, and any policies that have been changed as a result of End Point detection will revert to their default states. Maintaining the value of this object across agent reboots is REQUIRED.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

etsysConvEndPointGlobalConfigTable 1.3.6.1.4.1.5624.1.2.40.1.1.2
This table represents all Convergence End Point types supported by this entity, and provides a default policy profile for each Convergence End Point type.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysConvEndPointGlobalConfigEntry

etsysConvEndPointGlobalConfigEntry 1.3.6.1.4.1.5624.1.2.40.1.1.2.1
Defines the default policy to be applied when this type of Convergence End Point is detected or discovered.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysConvEndPointGlobalConfigEntry  

etsysConvEndPointGlobalEndPointType 1.3.6.1.4.1.5624.1.2.40.1.1.2.1.1
The Convergence End Point type. The value of this object is limited to a single enumerated bit in the ConvEndPointTypes textual convention.
Status: current Access: not-accessible
OBJECT-TYPE    
  ConvEndPointTypes  

etsysConvEndPointGlobalDefaultPolicyIndex 1.3.6.1.4.1.5624.1.2.40.1.1.2.1.2
The policy that should be applied for this type of Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If no such policy index exists, then no policy will be applied when this type of Convergence End Point is detected or discovered. The value zero is not a valid etsysPolicyProfileIndex, so zero indicates that no policy should be applied. Maintaining the value of this object across system reboots is REQUIRED.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 1..65535  

etsysConvEndPointProtocolConfigTable 1.3.6.1.4.1.5624.1.2.40.1.1.3
This table provides control of Convergence End Point detection and discovery on a per interface and per Convergence End Point type basis. Maintaining the values of this table across system reboots is REQUIRED.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysConvEndPointProtocolConfigEntry

etsysConvEndPointProtocolConfigEntry 1.3.6.1.4.1.5624.1.2.40.1.1.3.1
The current Convergence End Point detection and discovery status for an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysConvEndPointProtocolConfigEntry  

etsysConvEndPointProtocolEndPointType 1.3.6.1.4.1.5624.1.2.40.1.1.3.1.1
The Convergence End Point type.
Status: current Access: not-accessible
OBJECT-TYPE    
  ConvEndPointTypes  

etsysConvEndPointProtocolEnable 1.3.6.1.4.1.5624.1.2.40.1.1.3.1.2
When set to enabled(1), Convergence End Point detection and discovery will be enabled on this interface for the Convergence End Point type specified. When set to disabled(2), the Convergence End Points that have been discovered or detected on this interface of the type specified will be removed from the etsysConvEndPointConnMacTable and the etsysConvEndPointConnPortTable. After all of the End Points have been removed from an interface the policy on that interface will revert to its default state.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

etsysConvEndPointGlobalConfigAccountEnable 1.3.6.1.4.1.5624.1.2.40.1.1.4
When enabled(1), RADIUS accounting start, interim and stop frames are sent to the configured RADIUS server(s). When disabled(2), accounting packets are not sent to the RADIUS server.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

etsysConvEndPointConnMacTable 1.3.6.1.4.1.5624.1.2.40.1.2.1
This table provides information on each of the Convergence End Points that has been discovered or detected by this entity. Maintaining the value of this object across system reboots is NOT REQUIRED.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysConvEndPointConnMacEntry

etsysConvEndPointConnMacEntry 1.3.6.1.4.1.5624.1.2.40.1.2.1.1
Information about an individual Convergence End Point.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  EtsysConvEndPointConnMacEntry  

etsysConvEndPointConnMacMacAddress 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.1
The MAC address of this Convergence End Point.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  MacAddress  

etsysConvEndPointConnMacPortNumber 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.2
The interface on which this Convergence End Point was detected or discovered.
Status: deprecated Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

etsysConvEndPointConnMacEndPointType 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.3
The type of Convergence End Point described by this row.
Status: deprecated Access: read-only
OBJECT-TYPE    
  ConvEndPointTypes  

etsysConvEndPointConnMacPolicyIndex 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.4
The policy applied for this Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If the desired policy does not currently exist, or never did exist, then a zero MUST be returned.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

etsysConvEndPointConnMacDiscoveryTime 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.5
The time and date that this Convergence End Point was detected or discovered.
Status: deprecated Access: read-only
OBJECT-TYPE    
  DateAndTime  

etsysConvEndPointConnMacFirmwareVersion 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.6
This is the firmware version of the discovered Convergence End Point. If this information is not available via the detection protocol then a zero length string MUST be returned.
Status: deprecated Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

etsysConvEndPointConnMacInetAddressType 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.7
The address type of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return 'unknown'.
Status: deprecated Access: read-only
OBJECT-TYPE    
  InetAddressType  

etsysConvEndPointConnMacInetAddress 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.8
The address of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return a zero length string.
Status: deprecated Access: read-only
OBJECT-TYPE    
  InetAddress  

etsysConvEndPointConnPortTable 1.3.6.1.4.1.5624.1.2.40.1.2.2
This table provides a mapping from the entities interfaces to discovered Convergence End Points. Maintaining the value of this object across system reboots is NOT REQUIRED.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysConvEndPointConnPortEntry

etsysConvEndPointConnPortEntry 1.3.6.1.4.1.5624.1.2.40.1.2.2.1
Information about an individual Convergence End Point.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysConvEndPointConnPortEntry  

etsysConvEndPointConnPortMacAddress 1.3.6.1.4.1.5624.1.2.40.1.2.2.1.1
The MAC address of the discovered or detected Convergence End Point.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

etsysCEPConnMacTable 1.3.6.1.4.1.5624.1.2.40.1.2.3
This table provides information on each of the Convergence End Points that has been discovered or detected by this entity. Maintaining the value of this object across system reboots is NOT REQUIRED.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysCEPConnMacEntry

etsysCEPConnMacEntry 1.3.6.1.4.1.5624.1.2.40.1.2.3.1
Information about an individual Convergence End Point (CEP).
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysCEPConnMacEntry  

etsysCEPConnMacEndPointType 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.1
The type of Convergence End Point described by this row.
Status: current Access: read-only
OBJECT-TYPE    
  ConvEndPointTypes  

etsysCEPConnMacPolicyIndex 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.2
The policy applied for this Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If the desired policy does not currently exist, or never did exist, then a zero MUST be returned.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 1..65535  

etsysCEPConnMacDiscoveryTime 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.3
The time and date that this Convergence End Point was detected or discovered.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

etsysCEPConnMacFirmwareVersion 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.4
This is the firmware version of the discovered Convergence End Point. If this information is not available via the detection protocol then a zero length string MUST be returned.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

etsysCEPConnMacInetAddressType 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.5
The address type of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return 'unknown'.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

etsysCEPConnMacInetAddress 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.6
The address of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return a zero length string.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

etsysConvEndPointDetectionMaxEntries 1.3.6.1.4.1.5624.1.2.40.1.3.1
This value represents the maximum number of entries allowed in the etsysConvEndPointDetectionTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

etsysConvEndPointDetectionTable 1.3.6.1.4.1.5624.1.2.40.1.3.2
A table that describes the IP address and IP port based Convergence End Point detection parameters. Packets on interfaces that are configured to detect End Points, via the etsysConvEndPointProtocolConfigTable, that are defined in this table are inspected to determine if a Convergence End Point exists on that interface. Rules applying to Convergence End Point types that are configured for detection are evaluated according to the following: 1. If etsysConvEndPointDetectionProtocol does not have any bits set, this indicates that the port based detection should not be performed, proceed to step 2. Otherwise the value in etsysConvEndPointDetectionProtocol is evaluated against the protocol field in the IP header, if it is of a, or the, type specified then the destination port must be between the values of etsysConvEndPointDetectionPortLow and etsysConvEndPointDetectionPortHigh, inclusive. 2. If the etsysConvEndPointDetectionAddr is null, this indicates that no detection address check should be performed, consider the End Point detected. Otherwise the value the of etsysConvEndPointDetectionAddr will be masked with the value of etsysConvEndPointDetectionAddrMask, via a bitwise AND operation, and this value will be compared with the destination IP address that has also been masked with the value of etsysConvEndPointDetectionAddrMask, via a bitwise AND operation, if they are equal then consider the End Point detected. If there are no rows in this table that are in the active state then the following pseudo entries describe the behavior of the IP based Convergence End Point detection. EndPointType siemens Protocol { { udp, tcp } } PortLow 4060 PortHigh 4060 AddrType unknown Addr '' AddrMaskType unknown AddrMask '' EndPointType h323 Protocol { { udp, tcp } } PortLow 1718 PortHigh 1720 AddrType ipv4 Addr '224.0.1.41' AddrMaskType ipv4 AddrMask '255.255.255.255' EndPointType sip Protocol { { udp, tcp } } PortLow 5060 PortHigh 5060 AddrType ipv4 Addr '224.0.1.75' AddrMaskType ipv4 AddrMask '255.255.255.255' EndPointType h323 Protocol { { udp, tcp } } PortLow 1718 PortHigh 1720 AddrType unknown Addr '' AddrMaskType unknown AddrMask '' EndPointType sip Protocol { { udp, tcp } } PortLow 5060 PortHigh 5060 AddrType unknown Addr '' AddrMaskType unknown AddrMask '' If one or more entries in this table are active the active entries will define the IP based detection behavior in its entirety. Maintaining entries in this table across system reboots is REQUIRED for entries with an etsysConvEndPointDetectionRowStatus value of active(1).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysConvEndPointDetectionEntry

etsysConvEndPointDetectionEntry 1.3.6.1.4.1.5624.1.2.40.1.3.2.1
Each entry represents a describes parameters for detecting a Convergence End Point.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysConvEndPointDetectionEntry  

etsysConvEndPointDetectionRuleIndex 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.1
The index of this conceptual row. This row represents a single rule for determining if an incoming IP packet indicates the presence of a Convergence End Point device. The lower the numerical value of the index the greater the precedence of the rule. It is recommended that the lowest index be configured to most predominate protocol in the network for greater efficiency.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

etsysConvEndPointDetectionEndPointType 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.2
The Convergence End Point device type that a 'hit' on this rule will indicate the presence of.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER h323(0), siemens(1), sip(2)  

etsysConvEndPointDetectionProtocol 0.1.1.3.6.1.4.1.5624.1.2.40.1.3.2.1.3
The IP protocol type that the following port range applies to. If no bits are set then the destination port will not be evaluated as part of the detection process.
Status: current Access: read-create
OBJECT-TYPE    
  BITS udp(0), tcp(1)  

etsysConvEndPointDetectionPortLow 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.4
The low end of the range of the IP destination port that will be used for Convergence End Point detection. This value represents the low value in a range of port numbers that will be used to indicate this type of Convergence End Point. This value must be less than or equal to etsysConvEndPointDetectionPortHigh.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

etsysConvEndPointDetectionPortHigh 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.5
The high end of the range of the IP destination port that will be used for Convergence End Point detection. This value represents the high value in a range of port numbers that will be used to indicate this type of Convergence End Point. This value must be greater than or equal to etsysConvEndPointDetectionPortLow.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

etsysConvEndPointDetectionAddrType 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.6
The destination address type that will be used for Convergence End Point detection. If the address type is 'unknown', then this value will not be evaluated as part of the detection process.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

etsysConvEndPointDetectionAddr 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.7
The destination IP address that will be used for Convergence End Point detection. If this address is null, then this value will not be evaluated as part of the detection process.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

etsysConvEndPointDetectionAddrMaskType 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.8
The address type of the mask that will be applied to the destination IP address as part of the Convergence End Point detection process. If the address type is 'unknown', then this value will not be evaluated as part of the detection process.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

etsysConvEndPointDetectionAddrMask 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.9
The destination address mask that will be used for Convergence End Point detection. If the mask is null, then this value will not be evaluated as part of the detection process.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

etsysConvEndPointDetectionRowStatus 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.10
The status of this row as defined by the RowStatus textual convention. Rows in this table can only transition to 'notInService', or to 'active' if the etsysConvEndPointDetectionAddrType object and the etsysConvEndPointDetectionAddrMaskType object have the same value, and either their values are not 'unknown' or there is at least one bit set in the etsysConvEndPointDetectionProtocol object.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

etsysCEPDetectionPortConfigTable 1.3.6.1.4.1.5624.1.2.40.1.3.3
A table of per port configuration for Convergence End Point detection. Maintaining the value of this object across system reboots is NOT REQUIRED.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysCEPDetectionPortConfigEntry

etsysCEPDetectionPortConfigEntry 1.3.6.1.4.1.5624.1.2.40.1.3.3.1
An entry containing per port Convergence End Point data. Only interfaces that are able to detect Convergence End Points are represented in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysCEPDetectionPortConfigEntry  

etsysCEPPortClearUsers 1.3.6.1.4.1.5624.1.2.40.1.3.3.1.1
Setting this object to a value of true(1) will cause all detected or discovered Convergence End Points to be removed from the following status tables: etsysConvEndPointConnMacTable etsysConvEndPointConnPortTable etsysCEPConnMacTable Setting this object to a value of false(2) has no effect. This object will always return a value of false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

etsysCEPCdpPortConfigTable 1.3.6.1.4.1.5624.1.2.40.1.3.4
A table of per port configuration for Convergence End Point detection related to the Cisco CDP protocol. Only ports that are capable of participating in Cisco CDP protocol are represented in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysCEPCdpPortConfigEntry

etsysCEPCdpPortConfigEntry 1.3.6.1.4.1.5624.1.2.40.1.3.4.1
An entry containing per port Convergence End Point data. Only interfaces that are able to detect Convergence End Points are represented in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysCEPCdpPortConfigEntry  

etsysCEPCiscoCDPVoicePortVlan 1.3.6.1.4.1.5624.1.2.40.1.3.4.1.1
This object controls the behavior of the remote configuration of Cisco VOIP phones via Cisco CDP. Setting this object to a value of -1 will cause the device to not attempt to remotely configure a Cisco phone using CDP. Setting this object to a value of 0 will cause the device to configure the phone to send 802.1p priority tagged frames. A value of 4095 will cause the device to configure the phone to send untagged frames. A value in the range 1..4094 will cause the device to configure the phone to send 802.1Q tagged frames using that value as the VLAN ID encoded in the tag. This object SHOULD be maintained across device reboots.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 0 | 1..4094 | 4095  

etsysConvEndPointConformance 1.3.6.1.4.1.5624.1.2.40.2
OBJECT IDENTIFIER    

etsysConvEndPointGroups 1.3.6.1.4.1.5624.1.2.40.2.1
OBJECT IDENTIFIER    

etsysConvEndPointCompliances 1.3.6.1.4.1.5624.1.2.40.2.2
OBJECT IDENTIFIER    

etsysConvEndPointGlobalConfigGroup 1.3.6.1.4.1.5624.1.2.40.2.1.1
Objects which provide global control of the Convergence End Point features.
Status: deprecated Access: read-write
OBJECT-GROUP    

etsysConvEndPointConfigGroup 1.3.6.1.4.1.5624.1.2.40.2.1.2
Objects which provide overrides to the global Convergence End Point controls.
Status: current Access: read-write
OBJECT-GROUP    

etsysConvEndPointDetectionGroup 1.3.6.1.4.1.5624.1.2.40.2.1.3
Objects that provide configuration information specific to IP, port, and address based Convergence End Point detection.
Status: deprecated Access: read-write
OBJECT-GROUP    

etsysConvEndPointStatusGroup 1.3.6.1.4.1.5624.1.2.40.2.1.4
Objects that provide status information for discovered and detected Convergence End Points.
Status: deprecated Access: read-write
OBJECT-GROUP    

etsysConvEndPointStatusGroup2 1.3.6.1.4.1.5624.1.2.40.2.1.5
Objects that provide status information for discovered and detected Convergence End Points.
Status: current Access: read-write
OBJECT-GROUP    

etsysConvEndPointDetectionGroup2 1.3.6.1.4.1.5624.1.2.40.2.1.6
Objects that provide configuration information specific to IP, port, and address based Convergence End Point detection.
Status: current Access: read-write
OBJECT-GROUP    

etsysConvEndPointPortConfigGroup 1.3.6.1.4.1.5624.1.2.40.2.1.7
Objects that provide per port control for discovered and detected Convergence End Points.
Status: current Access: read-write
OBJECT-GROUP    

etsysConvEndPointCiscoVoiceVLANGroup 1.3.6.1.4.1.5624.1.2.40.2.1.8
Objects that provide per port control for configuring Cisco VOIP phones via Cisco CDP.
Status: current Access: read-write
OBJECT-GROUP    

etsysConvEndPointGlobalConfigGroup2 1.3.6.1.4.1.5624.1.2.40.2.1.9
Objects which provide global control of the Convergence End Point features.
Status: current Access: read-write
OBJECT-GROUP    

etsysConvEndPointCompliance 1.3.6.1.4.1.5624.1.2.40.2.2.1
This compliance statement has been deprecated in favor of the etsysConvEndPointCompliance2 group.
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

etsysConvEndPointCompliance2 1.3.6.1.4.1.5624.1.2.40.2.2.2
The compliance statement for entities which implement the Enterasys Convergence End Point Management MIB.
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

etsysConvEndPointPortConfigCompliance 1.3.6.1.4.1.5624.1.2.40.2.2.3
The compliance statement for devices that support per port configuration of Convergence End Point detection and discovery.
Status: current Access: read-write
MODULE-COMPLIANCE    

etsysConvEndPointCiscoVoiceVLANCompliance 1.3.6.1.4.1.5624.1.2.40.2.2.4
The compliance statement for devices that support detection and configuration of Cisco VOIP phones via Cisco CDP.
Status: current Access: read-write
MODULE-COMPLIANCE    

etsysConvEndPointCompliance3 1.3.6.1.4.1.5624.1.2.40.2.2.5
The compliance statement for entities which implement the Enterasys Convergence End Point Management MIB.
Status: current Access: read-write
MODULE-COMPLIANCE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor