ENGENIUS-PRIVATE-MIB

File: ENGENIUS-PRIVATE-MIB.mib (31568 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
RFC1213-MIB INET-ADDRESS-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
OBJECT-IDENTITY enterprises IpAddress
Counter32 Gauge32 TimeTicks
Integer32 Counter64 DisplayString
MacAddress TruthValue TimeStamp
TimeInterval DateAndTime RowStatus
TEXTUAL-CONVENTION MODULE-COMPLIANCE OBJECT-GROUP
ifIndex InetAddressType InetAddress

Defined Types

WLANTableEntry  
SEQUENCE    
  wlanTableIndex Integer32
  wlanEnable INTEGER
  wlanSSID DisplayString
  wlanHideSSID INTEGER
  wlanStaSeparation INTEGER
  wlanVLANID Integer32
  wlanAuth INTEGER
  wlanEncryption INTEGER
  wlanWepDefaultKeyIdx INTEGER
  wlanWepKey DisplayString
  wlanWpapskPassphrase DisplayString
  wlanWpaRadiusSrvIP IpAddress
  wlanWpaRadiusSrvPort Integer32
  wlanWpaRadiusSrvSecret DisplayString
  wlanWpaGroupKeyUpdateInterval Integer32

Defined Values

engeniusprivate 1.3.6.1.4.1.14125.2
The MIB module defines Senao implementation-specific metrics useful in managing IEEE 802.11 on Senao devices. This is used as a supplement to the standard 802.11 MIB proposed by IEEE.
MODULE-IDENTITY    

engenius 1.3.6.1.4.1.14125
OBJECT IDENTIFIER    

status 1.3.6.1.4.1.14125.2.1
OBJECT IDENTIFIER    

configuration 1.3.6.1.4.1.14125.2.2
OBJECT IDENTIFIER    

command 1.3.6.1.4.1.14125.2.3
OBJECT IDENTIFIER    

system 1.3.6.1.4.1.14125.2.1.1
OBJECT IDENTIFIER    

wan 1.3.6.1.4.1.14125.2.2.1
OBJECT IDENTIFIER    

pppoe 1.3.6.1.4.1.14125.2.2.2
OBJECT IDENTIFIER    

dns 1.3.6.1.4.1.14125.2.2.3
OBJECT IDENTIFIER    

mtu 1.3.6.1.4.1.14125.2.2.4
OBJECT IDENTIFIER    

landhcp 1.3.6.1.4.1.14125.2.2.5
OBJECT IDENTIFIER    

ntp 1.3.6.1.4.1.14125.2.2.6
OBJECT IDENTIFIER    

admin 1.3.6.1.4.1.14125.2.2.8
OBJECT IDENTIFIER    

wlan 1.3.6.1.4.1.14125.2.2.9
OBJECT IDENTIFIER    

wlansta 1.3.6.1.4.1.14125.2.2.10
OBJECT IDENTIFIER    

wlanmesh 1.3.6.1.4.1.14125.2.2.11
OBJECT IDENTIFIER    

wlanstawds 1.3.6.1.4.1.14125.2.2.14
OBJECT IDENTIFIER    

stp 1.3.6.1.4.1.14125.2.2.15
OBJECT IDENTIFIER    

snmp 1.3.6.1.4.1.14125.2.2.16
OBJECT IDENTIFIER    

wmm 1.3.6.1.4.1.14125.2.2.17
OBJECT IDENTIFIER    

logemail 1.3.6.1.4.1.14125.2.2.20
OBJECT IDENTIFIER    

vpn 1.3.6.1.4.1.14125.2.2.21
OBJECT IDENTIFIER    

traffic 1.3.6.1.4.1.14125.2.2.22
OBJECT IDENTIFIER    

saveCmd 1.3.6.1.4.1.14125.2.3.1
OBJECT IDENTIFIER    

resetCmd 1.3.6.1.4.1.14125.2.3.2
OBJECT IDENTIFIER    

rebootCmd 1.3.6.1.4.1.14125.2.3.3
OBJECT IDENTIFIER    

systemName 1.3.6.1.4.1.14125.2.1.1.1
The DUT's system name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..256)  

sysPassword 1.3.6.1.4.1.14125.2.1.1.2
The password that system manager own.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..256)  

errMsg 1.3.6.1.4.1.14125.2.1.1.3
The error message record
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..256)  

statusWLANSTAAssoc 1.3.6.1.4.1.14125.2.1.1.4
The status of wireless interface connect to AP
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

modelName 1.3.6.1.4.1.14125.2.1.1.5
Firmware model name
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..256)  

wirelessMacAddress 1.3.6.1.4.1.14125.2.1.1.6
The wireless MAC address
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..17)  

wanIPAddress 1.3.6.1.4.1.14125.2.1.1.7
The WAN IP address
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wanSubnetMask 1.3.6.1.4.1.14125.2.1.1.8
The WAN subnet mask
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wanConnectionType 1.3.6.1.4.1.14125.2.2.1.1
The wan connection type which one of Static IP/DHCP/PPPoE/PPTP
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dhcp(1), static(2), pppoe(3)  

wanGeneralAccount 1.3.6.1.4.1.14125.2.2.1.2
The DUT network Account ID
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..256)  

wanGeneralDomain 1.3.6.1.4.1.14125.2.2.1.3
The DUT network Domain Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..256)  

wanGeneralIP 1.3.6.1.4.1.14125.2.2.1.4
The DUT wan interface static IP address in static connection type
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

wanGeneralSubnetMask 1.3.6.1.4.1.14125.2.2.1.5
The DUT wan interface subnet mask in static connection type
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

wanGeneralGateway 1.3.6.1.4.1.14125.2.2.1.6
The DUT networks gateway IP address in static connection type
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

wanPPPoELoginName 1.3.6.1.4.1.14125.2.2.2.1
PPPoE user name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..256)  

wanPPPoEPassword 1.3.6.1.4.1.14125.2.2.2.2
PPPoE password
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..256)  

wanPPPoEServiceName 1.3.6.1.4.1.14125.2.2.2.3
Specifies the desired PPPoE service name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..256)  

wanPPPoEConnectionType 1.3.6.1.4.1.14125.2.2.2.4
PPPoE connection type which keep alive or on demand.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER keepalive(0), connectondemand(1)  

wanPPPoEMaxIdleTime 1.3.6.1.4.1.14125.2.2.2.5
The max idle time (minutes) in connect on demand connection type
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..99  

wanPPPoERedialPeriod 1.3.6.1.4.1.14125.2.2.2.6
The redial period (seconds) in keep alive connection type
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 30..180  

wanDNSSourc 1.3.6.1.4.1.14125.2.2.3.1
Automatically gets DNS IP address from ISP or user sepcisicify
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER isp(0), specified(1)  

wanPrimaryDNSIP 1.3.6.1.4.1.14125.2.2.3.2
The primary DNS IP address
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

wanSecondaryDNSIP 1.3.6.1.4.1.14125.2.2.3.3
The secondary DNS IP address
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

wanMTUMode 1.3.6.1.4.1.14125.2.2.4.1
Automatically setting MTU value or user sepcisicify
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(0), manual(1)  

wanMTU 1.3.6.1.4.1.14125.2.2.4.2
The Maximum Transmission Unit (MTU) in WAN interface
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 576..1500  

pppoeMTU 1.3.6.1.4.1.14125.2.2.4.3
The Maximum Transmission Unit (MTU) in PPPoE protocol
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 576..1492  

lanDHCPC 1.3.6.1.4.1.14125.2.2.5.1
Automatically get LAN IP address form DHCP server or set static IP address
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lanIP 1.3.6.1.4.1.14125.2.2.5.2
To setting static LAN IP address in DUT
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

lanSubnetmask 1.3.6.1.4.1.14125.2.2.5.3
To setting static Subnet Mask in DUT
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

lanGatewayIP 1.3.6.1.4.1.14125.2.2.5.4
To setting getway IP address in DUT
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

lanWINSAddr 1.3.6.1.4.1.14125.2.2.5.5
To setting WINS IP address in DUT
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

lanDHCPSrvEnable 1.3.6.1.4.1.14125.2.2.5.6
Enable / Disable DHCP server
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lanDHCPSrvStartAddr 1.3.6.1.4.1.14125.2.2.5.7
To setting DHCP server allocate IP address up bound
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

lanDHCPSrvStopAddr 1.3.6.1.4.1.14125.2.2.5.8
To setting DHCP server allocate IP address low bound
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

timeSettingMode 1.3.6.1.4.1.14125.2.2.6.1
Automatically get or manually set Date and Time
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER manual(0), auto(1)  

userNTPSrvMode 1.3.6.1.4.1.14125.2.2.6.2
Enable / Disable user sepcisicify NTP server
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

userNTPSrvIP 1.3.6.1.4.1.14125.2.2.6.3
User sepcisicify NTP server IP address
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

timeZone 1.3.6.1.4.1.14125.2.2.6.4
To setting time zone in DUT
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

username 1.3.6.1.4.1.14125.2.2.8.1
The User Name that system manager own
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..33)  

remoteManagementEnable 1.3.6.1.4.1.14125.2.2.8.3
Enable / Disable remote management DUT function
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

remoteUpgradeEnable 1.3.6.1.4.1.14125.2.2.8.4
Enable / Disable remote upgrade firmware
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

remoteManagementPort 1.3.6.1.4.1.14125.2.2.8.5
To setting remote management port
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

remoteManagementVLANID 1.3.6.1.4.1.14125.2.2.8.6
To setting management Tag on VLAN
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..4096  

wlanMode 1.3.6.1.4.1.14125.2.2.9.1
The wireless lan operation mode. (802.11a/b/g)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER wlan11a(1), wlan11b(2), wlan11bg(3), wlan11astaticturbo(5), wlan11gdynamicturbo(6), wlan11gstaticturbo(7), wlan11gpure(9)  

chanBwMode 1.3.6.1.4.1.14125.2.2.9.2
The WLAN narrow band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER wlan20MHz(0), wlan10MHz(1), wlan5MHz(2)  

wlanaSSID 1.3.6.1.4.1.14125.2.2.9.3
The SSID which station connect to
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..33)  

wlanOpMode 1.3.6.1.4.1.14125.2.2.9.4
The WLAN operation mode. (Access Point/ Client Bridge/ WDS Bridge/ Repeater/ AP Router / Client Router)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER accesspoint(0), clientbridge(1), wdsbridge(2), repeater(3), aprouter(4), clientrouter(5), mesh(6)  

wlanCountryCode 1.3.6.1.4.1.14125.2.2.9.5
The country code
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..5)  

wlanCountry 1.3.6.1.4.1.14125.2.2.9.6
The string of the country name
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

wlanChannel 1.3.6.1.4.1.14125.2.2.9.7
The wireless channel frequency
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

wlanACLMode 1.3.6.1.4.1.14125.2.2.9.8
The WLAN Mac filter mode. (Disable / Deny / Allow)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), allow(1), deny(2)  

wlanOutdoorDistance 1.3.6.1.4.1.14125.2.2.9.9
The distance between two DUTs
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1000..30000  

wlanDataRate 1.3.6.1.4.1.14125.2.2.9.10
The wireless LAN Data rate. The available input option: 1M, 2M, 5.5M, 6M, 9M, 11M, 12M, 18M, 24M, 36M, 48M, 54M, auto
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

wlanTxPower 1.3.6.1.4.1.14125.2.2.9.11
The WLAN transmission power
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..30  

antennasel 1.3.6.1.4.1.14125.2.2.9.12
The antenna which prefer to use
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER diversity(0), vertical(1), horizontal(2)  

wlanBeaconInterval 1.3.6.1.4.1.14125.2.2.9.13
The sent beacon interval time
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 25..500  

wlanRTSTh 1.3.6.1.4.1.14125.2.2.9.15
The WLAN RTS/CTS threshold
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..2346  

wlanFragLen 1.3.6.1.4.1.14125.2.2.9.16
The WLAN packages fragment length
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 256..2346  

wlanProtmode 1.3.6.1.4.1.14125.2.2.9.18
Protection transmittion on G band. (CTS or RTS/CTS)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), ctsonly(1), rtscts(2)  

wlanPreferBSSID 1.3.6.1.4.1.14125.2.2.9.19
The MAC address of the prefer connection AP
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

wlanTable 1.3.6.1.4.1.14125.2.2.9.21
This table display the wlan table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WLANTableEntry

wlanTableEntry 1.3.6.1.4.1.14125.2.2.9.21.1
Represent the entry in the wlan table.
Status: current Access: not-accessible
OBJECT-TYPE    
  WLANTableEntry  

wlanTableIndex 1.3.6.1.4.1.14125.2.2.9.21.1.1
Specify the index of the wlan table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..4  

wlanEnable 1.3.6.1.4.1.14125.2.2.9.21.1.2
Enable / Disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

wlanSSID 1.3.6.1.4.1.14125.2.2.9.21.1.3
The WLAN SSID
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..32)  

wlanHideSSID 1.3.6.1.4.1.14125.2.2.9.21.1.4
Enable / Disable broadcast SSID
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

wlanStaSeparation 1.3.6.1.4.1.14125.2.2.9.21.1.5
Enable / Disable STA separation
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

wlanVLANID 1.3.6.1.4.1.14125.2.2.9.21.1.6
The WLAN interface VLAN ID
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..4095  

wlanAuth 1.3.6.1.4.1.14125.2.2.9.21.1.7
The WLAN authentication type
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER open(1), shared(2), auto(3), wlan8021x(4), wpa(5), wpapsk(6), wpa2(7), wpa2psk(8), wpamixed(9), wpapskmixed(10)  

wlanEncryption 1.3.6.1.4.1.14125.2.2.9.21.1.8
The WLAN encryption type
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), wep(1), tkip(2), aes(3), auto(4)  

wlanWepDefaultKeyIdx 1.3.6.1.4.1.14125.2.2.9.21.1.9
The WLAN WEP Key index of combination
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER key1(1), key2(2), key3(3), key4(4)  

wlanWepKey 1.3.6.1.4.1.14125.2.2.9.21.1.10
The WLAN WEP Key combination. The input has to be 5,13,16 ascii keys, or 10,26,32 Hex keys
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(5|10|13|16|26|32)  

wlanWpapskPassphrase 1.3.6.1.4.1.14125.2.2.9.21.1.11
The WLAN WPA Key combination
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..64)  

wlanWpaRadiusSrvIP 1.3.6.1.4.1.14125.2.2.9.21.1.12
The WLAN WPA-Enterprise remote radius server IP
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

wlanWpaRadiusSrvPort 1.3.6.1.4.1.14125.2.2.9.21.1.13
The WLAN WPA-Enterprise remote radius server port
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

wlanWpaRadiusSrvSecret 1.3.6.1.4.1.14125.2.2.9.21.1.14
The WLAN WPA-Enterprise key combination
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..64)  

wlanWpaGroupKeyUpdateInterval 1.3.6.1.4.1.14125.2.2.9.21.1.15
The WLAN WPA-Enterprise group key update interval
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 30..3600  

wlanSTAAuth 1.3.6.1.4.1.14125.2.2.10.1
The WLAN STA authentication type
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER open(1), shared(2), wpapsk(6), wpa2psk(8), wpapskmixed(10)  

wlanSTAEncryption 1.3.6.1.4.1.14125.2.2.10.2
The WLAN STA encryption type
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), wep(1), tkip(2), aes(3), auto(4)  

wlanSTAWepDefaultKeyIdx 1.3.6.1.4.1.14125.2.2.10.3
The WLAN STA WEP Key index of combination
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER key1(1), key2(2), key3(3), key4(4)  

wlanSTAWepKey 1.3.6.1.4.1.14125.2.2.10.4
The WLAN STA WEP Key combination. The input has to be 5,13,16 ascii keys, or 10,26,32 Hex keys
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(5|10|13|16|26|32)  

wlanSTAWpapskPassphrase 1.3.6.1.4.1.14125.2.2.10.5
The WLAN STA WPA Key combination
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..64)  

wlanMESHSSID 1.3.6.1.4.1.14125.2.2.11.1
The string of the WLAN SSID in MESH mode
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..33)  

wlanMESHGateway 1.3.6.1.4.1.14125.2.2.11.2
The Gateway IP address in MESH mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

wlanMESHAuth 1.3.6.1.4.1.14125.2.2.11.4
The authentication type in MESH mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER open(1), shared(2)  

wlanMESHEncryption 1.3.6.1.4.1.14125.2.2.11.5
The encryption type in MESH mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), wep(1), aes(2)  

wlanMESHWepDefaultKeyIdx 1.3.6.1.4.1.14125.2.2.11.6
The WLAN WEP Key index of combination in MESH mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER key1(1), key2(2), key3(3), key4(4)  

wlanMESHWepKey 1.3.6.1.4.1.14125.2.2.11.7
The WLAN MESH WEP Key combination. The input has to be 5,13,16 ascii keys, or 10,26,32 Hex keys
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(5|10|13|16|26|32)  

wlanMESHWpapskPassphrase 1.3.6.1.4.1.14125.2.2.11.8
The WLAN WPA Key combination in MESH mode
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..64)  

staWDS 1.3.6.1.4.1.14125.2.2.14.1
Enable / Disable WDS link in Client Mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

stpMode 1.3.6.1.4.1.14125.2.2.15.1
Enable / Disable Spanning Tree
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

stpHelloTime 1.3.6.1.4.1.14125.2.2.15.2
The interval between periodic transmissions of Configuration Messages by Designated Ports. IEEE802.1D 17.13.6
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..10  

stpMaxAge 1.3.6.1.4.1.14125.2.2.15.3
The maximum age of the information transmitted by the Bridge when it is the Root Bridge. IEEE 802.1D 17.13.8
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 6..40  

stpForwardDelay 1.3.6.1.4.1.14125.2.2.15.4
The delay used by STP Bridges to transition Reoot and Designated Ports to Forwarding. IEEE 802.1D 17.13.5
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..30  

stpPriority 1.3.6.1.4.1.14125.2.2.15.5
The manageable component of the Port Identifier. IEEE 802.1D 17.13.10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

snmpEnable 1.3.6.1.4.1.14125.2.2.16.1
Enable / Disable SNMP agent
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

snmpCmntyRO 1.3.6.1.4.1.14125.2.2.16.2
The communication string for Read Only
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..33)  

snmpCmntyRW 1.3.6.1.4.1.14125.2.2.16.3
The communication string for Read Write
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..33)  

snmpTrapDstIP 1.3.6.1.4.1.14125.2.2.16.4
The IP address which snmp trap sent to
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

snmpTrapCmnty 1.3.6.1.4.1.14125.2.2.16.5
The communication string for trap message
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..33)  

snmpCont 1.3.6.1.4.1.14125.2.2.16.6
The snmp contact information
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..256)  

snmpLocation 1.3.6.1.4.1.14125.2.2.16.7
The snmp location information
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..256)  

sysObjectID 1.3.6.1.4.1.14125.2.2.16.8
The SNMP company OID
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

wmmEnable 1.3.6.1.4.1.14125.2.2.17.1
Enable / Disable WMM setting
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

logServerEnable 1.3.6.1.4.1.14125.2.2.20.1
Enable / Disable remote log server which log sent to
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

logServerIP 1.3.6.1.4.1.14125.2.2.20.2
Remote log server IP address
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

logLocalEnable 1.3.6.1.4.1.14125.2.2.20.3
Enable / Disable local log server
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

logLevel 1.3.6.1.4.1.14125.2.2.20.4
The level (all/ Debug/ Information/ Notice/ Warning/ Error/ Critical/ Alert/ Emergency) of log message
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER emergency(0), alert(1), critical(2), error(3), warning(4), notice(5), information(6), debug(7), all(8)  

vpnPassthroughPPTP 1.3.6.1.4.1.14125.2.2.21.1
Enable / Disable PPTP packages pass through
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

vpnPassthroughL2TP 1.3.6.1.4.1.14125.2.2.21.2
Enable / Disable L2TP packages pass through
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

vpnPassthroughIPSec 1.3.6.1.4.1.14125.2.2.21.3
Enable / Disable IPSec packages pass through
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

tcEnable 1.3.6.1.4.1.14125.2.2.22.1
Enable Traffic Shapping
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

tcInRate 1.3.6.1.4.1.14125.2.2.22.2
Incoming Traffic Limit, in kbits/s
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..999999  

tcInBurst 1.3.6.1.4.1.14125.2.2.22.3
Incoming Traffic Burst, in kBytes
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..999999  

tcOutRate 1.3.6.1.4.1.14125.2.2.22.4
Outgoing Traffic Limit, in kbits/s
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..999999  

tcOutBurst 1.3.6.1.4.1.14125.2.2.22.5
Outgoing Traffic Burst, in kBytes
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..999999  

executeSaveCmd 1.3.6.1.4.1.14125.2.3.1.1
SnmpSet with value 1 to execute the cfg_save() command.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1  

executeResetCmd 1.3.6.1.4.1.14125.2.3.2.1
SnmpSet with value 1 to execute the cfg_factory_default() command.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1  

executeRebootCmd 1.3.6.1.4.1.14125.2.3.3.1
Define the timeout (1~300seconds) and execute the reboot command.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..300