EICON-DIALER-MIB

File: EICON-DIALER-MIB.mib (128325 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB

Imported symbols

TimeTicks enterprises OBJECT-TYPE
DisplayString

Defined Types

PortRef  
INTEGER 1..48    

ActionState  
INTEGER done(1), failed(2), in-progress(3)    

DataEncoding  
INTEGER nrz(1), nrzi(2), fm0(3), fm1(4)    

ClockType  
INTEGER external(1), internal(2), ext-dpll(3), int-dpll(4)    

OnOff  
INTEGER on(1), off(2)    

FalseTrue  
INTEGER false(1), true(2)    

DisEnable  
INTEGER disable(1), enable(2)    

PrimBitRate  
INTEGER speed1200(1), speed2400(2), speed4800(3), speed7200(4), speed9600(5), speed12000(6), speed14400(7), not-supported(8)    

PrimCfg  
INTEGER v22bis(1), v32(2), v32tcm(3), v32bis(4), not-supported(5)    

IsdnSpidStatus  
INTEGER uninit(1), init(2), blocked(3), illegal(4)    

IsdnDnType  
INTEGER unknown(1), international(2), national(3), net-specific(4), subscriber(5), abbreviated(6), illegal(7)    

IsdnDnPlan  
INTEGER unknown(1), isdn-numbering(2), data-numbering(3), private-net(4), telex-numbering(5), nat-numbering(6), illegal(7)    

IsdnSubType  
INTEGER nsap(1), user-specified(2), osi(3), illegal(4)    

IsdnTnsNetId  
INTEGER user-specified(1), national(2), international(3), illegal(4)    

IsdnTnsIdPlan  
INTEGER unknown(1), interlata(2), data(3), illegal(4)    

IsdnCallType  
INTEGER circuit-switched(1), packet-switched(2), nailed-packet(3), circuit-spv(4), fax-3(5), fax-4(6), btx(7), teletex(8), videotex(9), illegal(10)    

IsdnCallSpeed  
INTEGER speed-56k(1), speed-64k(2), speed-illegal(3)    

IsdnBChannels  
INTEGER b1-channel(1), b2-channel(2), illegal(3)    

IsdnAnsEnable  
INTEGER disabled(1), enabled(2), enabled-illegal(3)    

IsdnScrStatus  
INTEGER disabled(1), enabled(2), illegal(3)    

IsdnCallOpt  
INTEGER opt(1), option(2), call-opt(3)    

IsdnStoDefined  
INTEGER stored(1)    

IsdnTeiStatus  
INTEGER unassigned(1), outstanding(2), assigned(3), illegal(4)    

IsdnL2State  
INTEGER null-state(1), tei-unassigned(2), assign-awaiting-tei(3), establish-awaiting-tei(4), tei-assigned(5), awaiting-established(6), awaiting-release(7), mutiple-frame-established(8), timer-recovery(9), illegal(10)    

IsdnL3State  
INTEGER null-state(1), call-init(2), overlap-sending(3), out-call-proc(4), call-delivered(5), undefined-state-5(6), call-present(7), call-received(8), connect-request(9), in-call-proc(10), call-active(11), disconnect-request(12), disconnect-ind(13), undefined-state-13(14), call-passive(15), suspend-request(16), undefined-state-16(17), resume-request(18), undefined-state-18(19), release-request(20), register-request(21), cancel-request(22), undefined-state-22(23), undefined-state-23(24), undefined-state-24(25), overlap-receive(26), idle-state(27), establish-wait(28), asai-tr1-state(29), u10-hold-request(30), u10-transfer-request(31), u10-conference-request(32), u10-reconnect-request(33), u10-awaiting-disc(34), u10-call-on-hold(35), broadcast-state(36), illegal(37)    

IsdnP3State  
INTEGER closed(1), opening(2), opened(3), tei-establishment(4), sw-activation(5), activated(6), deactivated(7), closing(8), illegal(9)    

IsdnActState  
INTEGER deactivated(1), activating(2), active(3), call-failed(4), activ-failed(5), illegal(6)    

IsdnNI1BCcState  
INTEGER null-state(1), idle(2), ringing(3), connected(4), dialing(5), lockout(6), offhook-releasing(7), onhook-releasing(8), originate(9), routing(10), call-queued(11), illegal(12)    

IsdnTR6BCcState  
INTEGER null-state(1), idle(2), ringing(3), connecting(4), connected(5), lockout(6), offhook-releasing(7), onhook-releasing(8), originate(9), routing(10), call-queued(11), illegal(12)    

IsdnVN3BCcState  
INTEGER null-state(1), idle(2), ringing(3), connecting(4), connected(5), lockout(6), offhook-releasing(7), onhook-releasing(8), originate(9), routing(10), call-queued(11), illegal(12)    

IsdnNET3BCcState  
INTEGER null-state(1), idle(2), ringing(3), connecting(4), connected(5), lockout(6), offhook-releasing(7), onhook-releasing(8), originate(9), routingout(10), call-queued(11), bell-releasing(12), illegal(13)    

IsdnTPHBCcState  
INTEGER null-state(1), idle(2), ringing(3), connected(4), dialing(5), lockout(6), offhook-releasing(7), onhook-releasing(8), originate(9), routing(10), call-queued(11), illegal(12)    

DialerInfoEntry  
SEQUENCE    
  dialerInfoPortRef PortRef
  dialerInfoType INTEGER
  dialerInfoTimeStart TimeTicks
  dialerInfoTimeConnect TimeTicks
  dialerInfoLineSpeed INTEGER
  dialerInfoDataEncoding DataEncoding
  dialerInfoClockType ClockType

DialerDirectInfoEntry  
SEQUENCE    
  dialerDirectPortRef PortRef
  dialerDirectIfType INTEGER
  dialerDirectMode INTEGER
  dialerDirectConnDelay INTEGER
  dialerDirectRtsDelay INTEGER
  dialerDirectState INTEGER

DialerDirectRs232InfoEntry  
SEQUENCE    
  dialerDirectRs232PortRef PortRef
  dialerDirectRs232DbounceDelay INTEGER
  dialerDirectRs232DtrSignal OnOff
  dialerDirectRs232DsrSignal OnOff
  dialerDirectRs232RiSignal OnOff

DialerDirectX21InfoEntry  
SEQUENCE    
  dialerDirectX21PortRef PortRef
  dialerDirectX21CtrlSignal OnOff
  dialerDirectX21IndicSignal OnOff

DialerV25bisInfoEntry  
SEQUENCE    
  dialerV25bisPortRef PortRef
  dialerV25bisPrimaryNum DisplayString
  dialerV25bisSecondaryNum DisplayString
  dialerV25bisAnsEnable FalseTrue
  dialerV25bisRetryAllowed FalseTrue
  dialerV25bisMaxRetries INTEGER
  dialerV25bisRetryDelay INTEGER
  dialerV25bisConnDelay INTEGER
  dialerV25bisOnOffDelay INTEGER
  dialerV25bisLossDelay INTEGER
  dialerV25bisMinDsrOnDelay INTEGER
  dialerV25bisRiDtrDelay INTEGER
  dialerV25bisHangupDelay INTEGER
  dialerV25bisDeltaRiDelay INTEGER
  dialerV25bisCtsOnDelay INTEGER
  dialerV25bisDtrSignal OnOff
  dialerV25bisDsrSignal OnOff
  dialerV25bisCtsSignal OnOff
  dialerV25bisRiSignal OnOff
  dialerV25bisState INTEGER

DialerAtCmdInfoEntry  
SEQUENCE    
  dialerAtCmdPortRef PortRef
  dialerAtCmdPrimaryNum DisplayString
  dialerAtCmdSecondaryNum DisplayString
  dialerAtCmdAnsEnable FalseTrue
  dialerAtCmdRetryAllowed FalseTrue
  dialerAtCmdMaxRetries INTEGER
  dialerAtCmdRetryDelay INTEGER
  dialerAtCmdConnDelay INTEGER
  dialerAtCmdOnOffDelay INTEGER
  dialerAtCmdLossDelay INTEGER
  dialerAtCmdMinDsrOnDelay INTEGER
  dialerAtCmdRiDtrDelay INTEGER
  dialerAtCmdHangupDelay INTEGER
  dialerAtCmdDeltaRiDelay INTEGER
  dialerAtCmdParity INTEGER
  dialerAtCmdBitsPerByte INTEGER
  dialerAtCmdModemSpeed INTEGER
  dialerAtCmdDtrSignal OnOff
  dialerAtCmdDsrSignal OnOff
  dialerAtCmdRiSignal OnOff
  dialerAtCmdState INTEGER

DialerV22BisDnaInfoEntry  
SEQUENCE    
  dialerV22BisDnaPortRef PortRef
  dialerV22BisDnaPrimaryNum DisplayString
  dialerV22BisDnaSecondaryNum DisplayString
  dialerV22BisDnaAnsEnable FalseTrue
  dialerV22BisDnaRetryAllowed FalseTrue
  dialerV22BisDnaMaxRetries INTEGER
  dialerV22BisDnaCallProgress FalseTrue
  dialerV22BisDnaDecadic FalseTrue
  dialerV22BisDnaMakeBreakRatio INTEGER
  dialerV22BisDnaRetryDelay INTEGER
  dialerV22BisDnaMinDialDelay INTEGER
  dialerV22BisDnaWaitDialTone INTEGER
  dialerV22BisDnaWaitCarrier INTEGER
  dialerV22BisDnaHndshkAbortTimer INTEGER
  dialerV22BisDnaGuardTone INTEGER
  dialerV22BisDnaPulseDelay INTEGER
  dialerV22BisDnaDTMFDuration INTEGER
  dialerV22BisDnaDTMFDelay INTEGER
  dialerV22BisDnaDTMFLevel INTEGER
  dialerV22BisDnaTxLevel INTEGER
  dialerV22BisDnaRxLevel FalseTrue
  dialerV22BisDnaRiNbr INTEGER
  dialerV22BisDnaDeltaRiDelay INTEGER
  dialerV22BisDnaRiDtrDelay INTEGER
  dialerV22BisDnaDsrRtsDelay INTEGER
  dialerV22BisDnaModemSpeed INTEGER
  dialerV22BisDnaDtrSignal OnOff
  dialerV22BisDnaDsrSignal OnOff
  dialerV22BisDnaRiSignal OnOff
  dialerV22BisDnaCdSignal OnOff
  dialerV22BisDnaToneInd OnOff
  dialerV22BisDnaDloInd OnOff
  dialerV22BisDnaState INTEGER

DialerV22BisImcInfoEntry  
SEQUENCE    
  dialerV22BisImcPortRef PortRef
  dialerV22BisImcPrimaryNum DisplayString
  dialerV22BisImcSecondaryNum DisplayString
  dialerV22BisImcAnsEnable FalseTrue
  dialerV22BisImcRetryAllowed FalseTrue
  dialerV22BisImcMaxRetries INTEGER
  dialerV22BisImcCallProgress FalseTrue
  dialerV22BisImcDecadic FalseTrue
  dialerV22BisImcMakeBreakRatio INTEGER
  dialerV22BisImcRetryDelay INTEGER
  dialerV22BisImcMinDialDelay INTEGER
  dialerV22BisImcWaitDialTone INTEGER
  dialerV22BisImcWaitCarrier INTEGER
  dialerV22BisImcHndshkAbortTimer INTEGER
  dialerV22BisImcGuardTone INTEGER
  dialerV22BisImcPulseDelay INTEGER
  dialerV22BisImcDTMFDuration INTEGER
  dialerV22BisImcDTMFDelay INTEGER
  dialerV22BisImcDTMFLevel INTEGER
  dialerV22BisImcTxLevel INTEGER
  dialerV22BisImcRxLevel INTEGER
  dialerV22BisImcRiNbr INTEGER
  dialerV22BisImcDeltaRiDelay INTEGER
  dialerV22BisImcRiDtrDelay INTEGER
  dialerV22BisImcDsrRtsDelay INTEGER
  dialerV22BisImcModemSpeed INTEGER
  dialerV22BisImcDtrSignal OnOff
  dialerV22BisImcDsrSignal OnOff
  dialerV22BisImcRiSignal OnOff
  dialerV22BisImcCdSignal OnOff
  dialerV22BisImcToneInd OnOff
  dialerV22BisImcDloInd OnOff
  dialerV22BisImcLineType INTEGER
  dialerV22BisImcLeasedOpertn INTEGER
  dialerV22BisImcSpeakerLevel INTEGER
  dialerV22BisImcState INTEGER

DialerV32BisInfoEntry  
SEQUENCE    
  dialerV32BisPortRef PortRef
  dialerV32BisPrimNum DisplayString
  dialerV32BisSecNum DisplayString
  dialerV32BisOverrNum DisplayString
  dialerV32BisCurrNum DisplayString
  dialerV32BisPrimBitRate PrimBitRate
  dialerV32BisSecBitRate PrimBitRate
  dialerV32BisOverrBitRate PrimBitRate
  dialerV32BisCurrBitRate PrimBitRate
  dialerV32BisPrimConfig PrimCfg
  dialerV32BisSecConfig PrimCfg
  dialerV32BisOverrConfig PrimCfg
  dialerV32BisCurrConfig PrimCfg
  dialerV32BisCurrRetry INTEGER
  dialerV32BisRingCount INTEGER
  dialerV32BisAnsEnable FalseTrue
  dialerV32BisDialMethod INTEGER
  dialerV32BisRetry FalseTrue
  dialerV32BisCallFailure INTEGER
  dialerV32BisCarrierDetect INTEGER
  dialerV32BisCarrierWait INTEGER
  dialerV32BisHangupVerify INTEGER
  dialerV32BisHangupSignal DisEnable
  dialerV32BisTxLevel INTEGER
  dialerV32BisRxLevel INTEGER
  dialerV32BisGuardTone INTEGER
  dialerV32BisLeasedLine INTEGER
  dialerV32BisLeaseMode INTEGER
  dialerV32BisLLTxLevel INTEGER
  dialerV32BisLLConfig PrimCfg
  dialerV32BisLLBitRate PrimBitRate
  dialerV32BisCallingTone DisEnable
  dialerV32BisAutoMode DisEnable
  dialerV32BisRetryAllowed DisEnable
  dialerV32BisMaxRetry INTEGER
  dialerV32BisDialTone DisEnable
  dialerV32BisDialToneWait INTEGER
  dialerV32BisRetryWait INTEGER
  dialerV32BisHangupWait INTEGER
  dialerV32BisDialPauseWait INTEGER
  dialerV32BisDeltaRiWait INTEGER
  dialerV32BisDTMFDuration INTEGER
  dialerV32BisDTMFDelay INTEGER
  dialerV32BisDTMFFreq1Level INTEGER
  dialerV32BisDTMFFreq2Level INTEGER
  dialerV32BisPulseMakeTime INTEGER
  dialerV32BisPulseBreakTime INTEGER
  dialerV32BisPulseDelay INTEGER
  dialerV32BisSpeakerLevel INTEGER
  dialerV32BisRiToAnswer INTEGER
  dialerV32BisAnswerBitRate PrimBitRate
  dialerV32BisAnswerConfig PrimCfg
  dialerV32BisRetrain OnOff
  dialerV32BisEqmLevel INTEGER
  dialerV32BisRiOnOffDetect OnOff
  dialerV32BisCdDetect OnOff
  dialerV32BisRingbackDetect OnOff
  dialerV32BisAnswerDetect OnOff
  dialerV32BisBusyDetect OnOff
  dialerV32BisDiscDetect OnOff
  dialerV32BisCdSignal OnOff
  dialerV32BisDsrSignal OnOff
  dialerV32BisState INTEGER

DialerControlEntry  
SEQUENCE    
  dialerCtrlPortRef PortRef
  dialerCtrlAction INTEGER
  dialerCtrlAnsEnable FalseTrue
  dialerCtrlDirectDSROnOff OnOff
  dialerCtrlNumber DisplayString
  dialerCtrlScriptFile DisplayString
  dialerCtrlActionState ActionState
  dialerCtrlActionError INTEGER
  dialerCtrlConfig PrimCfg
  dialerCtrlBitRate PrimBitRate
  dialerCtrlType IsdnDnType
  dialerCtrlPlan IsdnDnPlan
  dialerCtrlSub DisplayString
  dialerCtrlSubType IsdnSubType
  dialerCtrlTns DisplayString
  dialerCtrlNumberTemp DisplayString
  dialerCtrlDialMask INTEGER
  dialerCtrlCallSpeed INTEGER

DialerIsdnStatusEntry  
SEQUENCE    
  dialerIsdnStatusPortRef PortRef
  dialerIsdnStatusSwitchType INTEGER
  dialerIsdnStatusChType INTEGER
  dialerIsdnStatusL1State INTEGER
  dialerIsdnStatusState INTEGER

DialerIsdnNI1BChEntry  
SEQUENCE    
  dialerIsdnNI1BChPortRef PortRef
  dialerIsdnNI1BChSpid DisplayString
  dialerIsdnNI1BChSpidStatus IsdnSpidStatus
  dialerIsdnNI1BChLocalDn DisplayString
  dialerIsdnNI1BChLocalSub DisplayString
  dialerIsdnNI1BChTnsDigs DisplayString
  dialerIsdnNI1BChRemoteDn DisplayString
  dialerIsdnNI1BChRemoteSub DisplayString
  dialerIsdnNI1BChCallType IsdnCallType
  dialerIsdnNI1BChCallSpeed IsdnCallSpeed
  dialerIsdnNI1BChBChannel IsdnBChannels
  dialerIsdnNI1BChAnsEnable IsdnAnsEnable
  dialerIsdnNI1BChCcState IsdnNI1BCcState
  dialerIsdnNI1BChCcNbCause INTEGER
  dialerIsdnNI1BChCcCause OCTET STRING
  dialerIsdnNI1BChL3State IsdnL3State
  dialerIsdnNI1BChL2State IsdnL2State
  dialerIsdnNI1BChTeiValue INTEGER
  dialerIsdnNI1BChTeiStatus IsdnTeiStatus
  dialerIsdnNI1BChLocalDnType IsdnDnType
  dialerIsdnNI1BChLocalDnPlan IsdnDnPlan
  dialerIsdnNI1BChLocalSubType IsdnSubType
  dialerIsdnNI1BChTnsNetId IsdnTnsNetId
  dialerIsdnNI1BChTnsIdPlan IsdnTnsIdPlan
  dialerIsdnNI1BChRemoteDnType IsdnDnType
  dialerIsdnNI1BChRemoteDnPlan IsdnDnPlan
  dialerIsdnNI1BChRemoteSubType IsdnSubType
  dialerIsdnNI1BChScrStatus IsdnScrStatus
  dialerIsdnNI1BChCallOpt IsdnCallOpt
  dialerIsdnNI1BChStoDefined IsdnStoDefined
  dialerIsdnNI1BChStoDnType INTEGER
  dialerIsdnNI1BChStoDnPlan INTEGER
  dialerIsdnNI1BChStoDn DisplayString
  dialerIsdnNI1BChStoSubType INTEGER
  dialerIsdnNI1BChStoSub DisplayString
  dialerIsdnNI1BChStoTnsNetId INTEGER
  dialerIsdnNI1BChStoTnsPlan INTEGER
  dialerIsdnNI1BChStoDigs DisplayString
  dialerIsdnNI1BChStoBcType INTEGER
  dialerIsdnNI1BChStoBcOpt INTEGER

DialerIsdnNI1DChEntry  
SEQUENCE    
  dialerIsdnNI1DChPortRef PortRef
  dialerIsdnNI1DChTeiValue INTEGER
  dialerIsdnNI1DChTeiStatus IsdnTeiStatus
  dialerIsdnNI1DChL2State IsdnL2State
  dialerIsdnNI1DChP3State IsdnP3State
  dialerIsdnNI1DChActState IsdnActState

DialerIsdnTR6BChEntry  
SEQUENCE    
  dialerIsdnTR6BChPortRef PortRef
  dialerIsdnTR6BChLocalDn DisplayString
  dialerIsdnTR6BChRemoteDn DisplayString
  dialerIsdnTR6BChCallType IsdnCallType
  dialerIsdnTR6BChCallSpeed IsdnCallSpeed
  dialerIsdnTR6BChBChannel IsdnBChannels
  dialerIsdnTR6BChAnsEnable IsdnAnsEnable
  dialerIsdnTR6BChCcState IsdnTR6BCcState
  dialerIsdnTR6BChCcNbCause INTEGER
  dialerIsdnTR6BChCcCause OCTET STRING
  dialerIsdnTR6BChL3State IsdnL3State
  dialerIsdnTR6BChL2State IsdnL2State
  dialerIsdnTR6BChLocalDnType IsdnDnType
  dialerIsdnTR6BChLocalDnPlan IsdnDnPlan
  dialerIsdnTR6BChRemoteDnType IsdnDnType
  dialerIsdnTR6BChRemoteDnPlan IsdnDnPlan
  dialerIsdnTR6BChScrStatus IsdnScrStatus
  dialerIsdnTR6BChCallOpt IsdnCallOpt
  dialerIsdnTR6BChTeiValue INTEGER
  dialerIsdnTR6BChTeiStatus IsdnTeiStatus
  dialerIsdnTR6BChStoDefined IsdnStoDefined
  dialerIsdnTR6BChStoDnType INTEGER
  dialerIsdnTR6BChStoDnPlan INTEGER
  dialerIsdnTR6BChStoDn DisplayString
  dialerIsdnTR6BChStoBcType INTEGER
  dialerIsdnTR6BChStoBcOpt INTEGER

DialerIsdnVN3BChEntry  
SEQUENCE    
  dialerIsdnVN3BChPortRef PortRef
  dialerIsdnVN3BChLocalDnType IsdnDnType
  dialerIsdnVN3BChLocalDnPlan IsdnDnPlan
  dialerIsdnVN3BChLocalDn DisplayString
  dialerIsdnVN3BChLocalSubType IsdnSubType
  dialerIsdnVN3BChLocalSub DisplayString
  dialerIsdnVN3BChRemoteDnType IsdnDnType
  dialerIsdnVN3BChRemoteDnPlan IsdnDnPlan
  dialerIsdnVN3BChRemoteDn DisplayString
  dialerIsdnVN3BChRemoteSubType IsdnSubType
  dialerIsdnVN3BChRemoteSub DisplayString
  dialerIsdnVN3BChCallType IsdnCallType
  dialerIsdnVN3BChCallSpeed IsdnCallSpeed
  dialerIsdnVN3BChBChannel IsdnBChannels
  dialerIsdnVN3BChAnsEnable IsdnAnsEnable
  dialerIsdnVN3BChScrStatus IsdnScrStatus
  dialerIsdnVN3BChCallOpt IsdnCallOpt
  dialerIsdnVN3BChCcState IsdnVN3BCcState
  dialerIsdnVN3BChCcNbCause INTEGER
  dialerIsdnVN3BChCcCause OCTET STRING
  dialerIsdnVN3BChL3State IsdnL3State
  dialerIsdnVN3BChL2State IsdnL2State
  dialerIsdnVN3BChTeiValue INTEGER
  dialerIsdnVN3BChTeiStatus IsdnTeiStatus
  dialerIsdnVN3BChStoDefined IsdnStoDefined
  dialerIsdnVN3BChStoDnType INTEGER
  dialerIsdnVN3BChStoDnPlan INTEGER
  dialerIsdnVN3BChStoDn DisplayString
  dialerIsdnVN3BChStoSubType INTEGER
  dialerIsdnVN3BChStoSub DisplayString
  dialerIsdnVN3BChStoBcType INTEGER
  dialerIsdnVN3BChStoBcOpt INTEGER

DialerIsdnVN3DChEntry  
SEQUENCE    
  dialerIsdnVN3DChPortRef PortRef
  dialerIsdnVN3DChTeiValue INTEGER
  dialerIsdnVN3DChTeiStatus IsdnTeiStatus
  dialerIsdnVN3DChL2State IsdnL2State
  dialerIsdnVN3DChP3State IsdnP3State

DialerIsdnNET3BChEntry  
SEQUENCE    
  dialerIsdnNET3BChPortRef PortRef
  dialerIsdnNET3BChLocalDnType IsdnDnType
  dialerIsdnNET3BChLocalDnPlan IsdnDnPlan
  dialerIsdnNET3BChLocalDn DisplayString
  dialerIsdnNET3BChLocalSubType IsdnSubType
  dialerIsdnNET3BChLocalSub DisplayString
  dialerIsdnNET3BChRemoteDnType IsdnDnType
  dialerIsdnNET3BChRemoteDnPlan IsdnDnPlan
  dialerIsdnNET3BChRemoteDn DisplayString
  dialerIsdnNET3BChRemoteSubType IsdnSubType
  dialerIsdnNET3BChRemoteSub DisplayString
  dialerIsdnNET3BChCallType IsdnCallType
  dialerIsdnNET3BChCallSpeed IsdnCallSpeed
  dialerIsdnNET3BChBChannel IsdnBChannels
  dialerIsdnNET3BChAnsEnable IsdnAnsEnable
  dialerIsdnNET3BChTnsNetId IsdnTnsNetId
  dialerIsdnNET3BChTnsIdPlan IsdnTnsIdPlan
  dialerIsdnNET3BChTnsDigs DisplayString
  dialerIsdnNET3BChScrStatus IsdnScrStatus
  dialerIsdnNET3BChCallOpt IsdnCallOpt
  dialerIsdnNET3BChCcState IsdnNET3BCcState
  dialerIsdnNET3BChCcNbCause INTEGER
  dialerIsdnNET3BChCcCause OCTET STRING
  dialerIsdnNET3BChL3State IsdnL3State
  dialerIsdnNET3BChL2State IsdnL2State
  dialerIsdnNET3BChTeiValue INTEGER
  dialerIsdnNET3BChTeiStatus IsdnTeiStatus
  dialerIsdnNET3BChStoDefined IsdnStoDefined
  dialerIsdnNET3BChStoDnType INTEGER
  dialerIsdnNET3BChStoDnPlan INTEGER
  dialerIsdnNET3BChStoDn DisplayString
  dialerIsdnNET3BChStoSubType INTEGER
  dialerIsdnNET3BChStoSub DisplayString
  dialerIsdnNET3BChStoTnsNetId INTEGER
  dialerIsdnNET3BChStoTnsPlan INTEGER
  dialerIsdnNET3BChStoDigs DisplayString
  dialerIsdnNET3BChStoBcType INTEGER
  dialerIsdnNET3BChStoBcOpt INTEGER

DialerIsdnTPHBChEntry  
SEQUENCE    
  dialerIsdnTPHBChPortRef PortRef
  dialerIsdnTPHBChLocalDnType IsdnDnType
  dialerIsdnTPHBChLocalDnPlan IsdnDnPlan
  dialerIsdnTPHBChLocalDn DisplayString
  dialerIsdnTPHBChLocalSubType IsdnSubType
  dialerIsdnTPHBChLocalSub DisplayString
  dialerIsdnTPHBChRemoteDnType IsdnDnType
  dialerIsdnTPHBChRemoteDnPlan IsdnDnPlan
  dialerIsdnTPHBChRemoteDn DisplayString
  dialerIsdnTPHBChRemoteSubType IsdnSubType
  dialerIsdnTPHBChRemoteSub DisplayString
  dialerIsdnTPHBChCallType IsdnCallType
  dialerIsdnTPHBChCallSpeed IsdnCallSpeed
  dialerIsdnTPHBChBChannel IsdnBChannels
  dialerIsdnTPHBChAnsEnable IsdnAnsEnable
  dialerIsdnTPHBChScrStatus IsdnScrStatus
  dialerIsdnTPHBChCallOpt IsdnCallOpt
  dialerIsdnTPHBChCcState IsdnTPHBCcState
  dialerIsdnTPHBChCcNbCause INTEGER
  dialerIsdnTPHBChCcCause OCTET STRING
  dialerIsdnTPHBChL3State IsdnL3State
  dialerIsdnTPHBChL2State IsdnL2State
  dialerIsdnTPHBChTeiValue INTEGER
  dialerIsdnTPHBChTeiStatus IsdnTeiStatus
  dialerIsdnTPHBChStoDefined IsdnStoDefined
  dialerIsdnTPHBChStoDnType INTEGER
  dialerIsdnTPHBChStoDnPlan INTEGER
  dialerIsdnTPHBChStoDn DisplayString
  dialerIsdnTPHBChStoSubType INTEGER
  dialerIsdnTPHBChStoSub DisplayString
  dialerIsdnTPHBChStoBcType INTEGER
  dialerIsdnTPHBChStoBcOpt INTEGER

DialerIsdnTPHDChEntry  
SEQUENCE    
  dialerIsdnTPHDChPortRef PortRef
  dialerIsdnTPHDChTeiValue INTEGER
  dialerIsdnTPHDChTeiStatus IsdnTeiStatus
  dialerIsdnTPHDChL2State IsdnL2State
  dialerIsdnTPHDChP3State IsdnP3State

Defined Values

eicon 1.3.6.1.4.1.434
OBJECT IDENTIFIER    

management 1.3.6.1.4.1.434.2
OBJECT IDENTIFIER    

mibv2 1.3.6.1.4.1.434.2.2
OBJECT IDENTIFIER    

module 1.3.6.1.4.1.434.2.2.4
OBJECT IDENTIFIER    

dialer 1.3.6.1.4.1.434.2.2.4.16
OBJECT IDENTIFIER    

dialerInfoTable 1.3.6.1.4.1.434.2.2.4.16.1
General Information Table for dailer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerInfoEntry

dialerInfoEntry 1.3.6.1.4.1.434.2.2.4.16.1.1
The set of dialer configuration attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerInfoEntry  

dialerInfoPortRef 1.3.6.1.4.1.434.2.2.4.16.1.1.1
The id of the port, equal to portIndex from the port group. It identifies the port to which the configuration parameters apply.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerInfoType 1.3.6.1.4.1.434.2.2.4.16.1.1.2
Type of interface connecting the gateway to local or remote host computers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER direct(1), v25bis(2), v22bis(3), at-cmd(4), isdn-stat(5), v32bis(6), none(7), other(8)  

dialerInfoTimeStart 1.3.6.1.4.1.434.2.2.4.16.1.1.3
The time elapsed since the dialer was statrted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

dialerInfoTimeConnect 1.3.6.1.4.1.434.2.2.4.16.1.1.4
The time elapsed since the dialer established the current connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

dialerInfoLineSpeed 1.3.6.1.4.1.434.2.2.4.16.1.1.5
The speed setting of the driver (line speed), or the dialer (modem speed).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..99999  

dialerInfoDataEncoding 1.3.6.1.4.1.434.2.2.4.16.1.1.6
The type of data encoding used on the connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DataEncoding  

dialerInfoClockType 1.3.6.1.4.1.434.2.2.4.16.1.1.7
The type of clocking used by the modem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  ClockType  

dialerDirectInfoTable 1.3.6.1.4.1.434.2.2.4.16.2
General Information Table for Direct dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerDirectInfoEntry

dialerDirectInfoEntry 1.3.6.1.4.1.434.2.2.4.16.2.1
The set of dialer configuration attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerDirectInfoEntry  

dialerDirectPortRef 1.3.6.1.4.1.434.2.2.4.16.2.1.1
The id of the port, equal to portIndex from the port group. It identifies the port to which the configuration parameters apply.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerDirectIfType 1.3.6.1.4.1.434.2.2.4.16.2.1.2
Interface type of the Dialer
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER rs232(1), v35(2), x21(3)  

dialerDirectMode 1.3.6.1.4.1.434.2.2.4.16.2.1.3
States whether the modem is connected to a Leased or Dial-Up phone line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER leased(1), dial(2)  

dialerDirectConnDelay 1.3.6.1.4.1.434.2.2.4.16.2.1.4
Max time for connection in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerDirectRtsDelay 1.3.6.1.4.1.434.2.2.4.16.2.1.5
Delay between arrival of DSR and activation of RTS circuit in msec.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerDirectState 1.3.6.1.4.1.434.2.2.4.16.2.1.6
State of the Direct dialer: closed(1) - Modem signals on a dial modem were lost. opening(2) - Link is being set up (modem dialing). asnwering(3) - Accepting call from remote. delaying(4) - Waiting for a timer to expire. opened(5) - Physical link is established. Closing(6) - Disconnecting the physical link. ringing (7) - answer-wait (8) - originating (9) - connecting (10) - connect-delay (11) - connected (12) - disconnecting (13) - remote-disc (14) - local-disc (15) - connect-req (16) - incomming-call (17) - outgoing-call (18) - outgoing-delay (19) -
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER closed(1), opening(2), answering(3), delaying(4), opened(5), closing(6), ringing(7), answer-wait(8), originating(9), connecting(10), connect-delay(11), connected(12), disconnecting(13), remote-disc(14), local-disc(15), connect-req(16), incomming-call(17), outgoing-call(18), outgoing-delay(19)  

dialerDirectRs232InfoTable 1.3.6.1.4.1.434.2.2.4.16.3
General Information Table for Direct dialer RS232.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerDirectRs232InfoEntry

dialerDirectRs232InfoEntry 1.3.6.1.4.1.434.2.2.4.16.3.1
The set of dialer configuration attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerDirectRs232InfoEntry  

dialerDirectRs232PortRef 1.3.6.1.4.1.434.2.2.4.16.3.1.1
The id of the port, equal to portIndex from the port group. It identifies the port to which the configuration parameters apply.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerDirectRs232DbounceDelay 1.3.6.1.4.1.434.2.2.4.16.3.1.2
This applies to Leased line only. It is the amount of time, expressed in msecs, that DSR signal stays on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerDirectRs232DtrSignal 1.3.6.1.4.1.434.2.2.4.16.3.1.3
The current status of the DTR signal.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerDirectRs232DsrSignal 1.3.6.1.4.1.434.2.2.4.16.3.1.4
The current status of the DSR signal.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OnOff  

dialerDirectRs232RiSignal 1.3.6.1.4.1.434.2.2.4.16.3.1.5
The current status of the RI signal. This is set to ON when there is an incoming call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerDirectX21InfoTable 1.3.6.1.4.1.434.2.2.4.16.4
General Information Table for Direct dialer X21.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerDirectX21InfoEntry

dialerDirectX21InfoEntry 1.3.6.1.4.1.434.2.2.4.16.4.1
The set of dialer configuration attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerDirectX21InfoEntry  

dialerDirectX21PortRef 1.3.6.1.4.1.434.2.2.4.16.4.1.1
The id of the port, equal to portIndex from the port group. It identifies the port to which the configuration parameters apply.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerDirectX21CtrlSignal 1.3.6.1.4.1.434.2.2.4.16.4.1.2
The control circuit status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerDirectX21IndicSignal 1.3.6.1.4.1.434.2.2.4.16.4.1.3
The indication circuit status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV25bisInfoTable 1.3.6.1.4.1.434.2.2.4.16.5
General Information Table for V25Bis dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerV25bisInfoEntry

dialerV25bisInfoEntry 1.3.6.1.4.1.434.2.2.4.16.5.1
The set of dialer configuration attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerV25bisInfoEntry  

dialerV25bisPortRef 1.3.6.1.4.1.434.2.2.4.16.5.1.1
The Port Number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerV25bisPrimaryNum 1.3.6.1.4.1.434.2.2.4.16.5.1.2
The main telephone number stored in the dialer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerV25bisSecondaryNum 1.3.6.1.4.1.434.2.2.4.16.5.1.3
The alternate telephone number stored in the dialer. This number is dialed if the main number is busy of if there is no answer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerV25bisAnsEnable 1.3.6.1.4.1.434.2.2.4.16.5.1.4
States whether or not the dialer answers incoming calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FalseTrue  

dialerV25bisRetryAllowed 1.3.6.1.4.1.434.2.2.4.16.5.1.5
Indicates whether or not the dialer will try to redial a number that is busy or does not answer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FalseTrue  

dialerV25bisMaxRetries 1.3.6.1.4.1.434.2.2.4.16.5.1.6
Specifies how many times a number will be redialed if it is busy or otherwise unresponsive.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV25bisRetryDelay 1.3.6.1.4.1.434.2.2.4.16.5.1.7
The amount of time in msecs between redial attempts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV25bisConnDelay 1.3.6.1.4.1.434.2.2.4.16.5.1.8
Maximum delay for connection establishment (secs).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV25bisOnOffDelay 1.3.6.1.4.1.434.2.2.4.16.5.1.9
The delay allowed in seconds for the DSR to go off before hangup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV25bisLossDelay 1.3.6.1.4.1.434.2.2.4.16.5.1.10
Amount of delay in msecs before DSR debouncing for OFF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV25bisMinDsrOnDelay 1.3.6.1.4.1.434.2.2.4.16.5.1.11
Amount of delay in msecs before DSR debouncing for ON.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV25bisRiDtrDelay 1.3.6.1.4.1.434.2.2.4.16.5.1.12
Amount of delay in msec before raising DTR when RING occurs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV25bisHangupDelay 1.3.6.1.4.1.434.2.2.4.16.5.1.13
Amount of delay in secs before hangup, if DSR goes OFF in connected state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV25bisDeltaRiDelay 1.3.6.1.4.1.434.2.2.4.16.5.1.14
Delay in msecs before rings are no longer occur.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV25bisCtsOnDelay 1.3.6.1.4.1.434.2.2.4.16.5.1.15
Maximum delay in msecs for sending a message to the modem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV25bisDtrSignal 1.3.6.1.4.1.434.2.2.4.16.5.1.16
DTR status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV25bisDsrSignal 1.3.6.1.4.1.434.2.2.4.16.5.1.17
DSR status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV25bisCtsSignal 1.3.6.1.4.1.434.2.2.4.16.5.1.18
CTS status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV25bisRiSignal 1.3.6.1.4.1.434.2.2.4.16.5.1.19
RI status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV25bisState 1.3.6.1.4.1.434.2.2.4.16.5.1.20
The status of the V.25bis modem: on-hook (1) - Modem not active ready (2) - Connection established dialing (3) - Dialing a number connect (4) - Successful dial attemp data-tran (5) - Data transfer state enabled retrying (6) - Awaiting call attempt ringing (7) - Incoming call present ans-start (8) - Connect request received ans-cplt (9) - Call establised. hanging-up (10) - Dialer disconnecting from DCE ignore-ring (11) - Ringing signal ignored collision (12) - Collision between connection request and incoming call ans-accepting (13) - Accepted incoming call prog-rdy (14) - Dialer ready to communicate with modem program (15) - Modem ready to communicate with dialer prog-ring (16) - Signal detected from DCE prog-not-rdy (17) - Dialer not ready to communicate with modem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on-hook(1), ready(2), dialing(3), connect(4), data-tran(5), retrying(6), ringing(7), ans-start(8), ans-cplt(9), hanging-up(10), ignore-ring(11), collision(12), ans-accepting(13), prog-rdy(14), program(15), prog-ring(16), prog-not-rdy(17)  

dialerAtCmdInfoTable 1.3.6.1.4.1.434.2.2.4.16.6
General Information Table for AT-CMD dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerAtCmdInfoEntry

dialerAtCmdInfoEntry 1.3.6.1.4.1.434.2.2.4.16.6.1
The set of dialer configuration attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerAtCmdInfoEntry  

dialerAtCmdPortRef 1.3.6.1.4.1.434.2.2.4.16.6.1.1
The Port Number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerAtCmdPrimaryNum 1.3.6.1.4.1.434.2.2.4.16.6.1.2
The main telephone number stored in the dialer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerAtCmdSecondaryNum 1.3.6.1.4.1.434.2.2.4.16.6.1.3
The alternate telephone number stored in the dialer. This number is dialed if the main number is busy or if there is no answer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerAtCmdAnsEnable 1.3.6.1.4.1.434.2.2.4.16.6.1.4
States whether or not the dialer answers incoming calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FalseTrue  

dialerAtCmdRetryAllowed 1.3.6.1.4.1.434.2.2.4.16.6.1.5
Indicates whether or not the dialer will try to redial a number that is busy or does not answer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FalseTrue  

dialerAtCmdMaxRetries 1.3.6.1.4.1.434.2.2.4.16.6.1.6
Specifies how many times a number will be redialed if it is busy or otherwise unresponsive.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerAtCmdRetryDelay 1.3.6.1.4.1.434.2.2.4.16.6.1.7
The amount of time in msecs between redial attempts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerAtCmdConnDelay 1.3.6.1.4.1.434.2.2.4.16.6.1.8
Maximum delay for connection establishment (secs).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerAtCmdOnOffDelay 1.3.6.1.4.1.434.2.2.4.16.6.1.9
The delay allowed in seconds for the DSR signal to go off before hangup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerAtCmdLossDelay 1.3.6.1.4.1.434.2.2.4.16.6.1.10
Number of msecs allowed before DSR debouncing for OFF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerAtCmdMinDsrOnDelay 1.3.6.1.4.1.434.2.2.4.16.6.1.11
msecs DSR debouncing for ON before going OFF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerAtCmdRiDtrDelay 1.3.6.1.4.1.434.2.2.4.16.6.1.12
Amount of delay in msec, before raising DTR when RING occurs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerAtCmdHangupDelay 1.3.6.1.4.1.434.2.2.4.16.6.1.13
Amount of delay in secs before hangup, if DSR goes OFF in connected state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerAtCmdDeltaRiDelay 1.3.6.1.4.1.434.2.2.4.16.6.1.14
delay in msecs before rings no longer occur.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerAtCmdParity 1.3.6.1.4.1.434.2.2.4.16.6.1.15
The parity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), odd(2), even(3)  

dialerAtCmdBitsPerByte 1.3.6.1.4.1.434.2.2.4.16.6.1.16
The number of data bits per byte.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER data7(1), data8(2)  

dialerAtCmdModemSpeed 1.3.6.1.4.1.434.2.2.4.16.6.1.17
Modem Speed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerAtCmdDtrSignal 1.3.6.1.4.1.434.2.2.4.16.6.1.18
DTR status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerAtCmdDsrSignal 1.3.6.1.4.1.434.2.2.4.16.6.1.19
DSR status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerAtCmdRiSignal 1.3.6.1.4.1.434.2.2.4.16.6.1.20
RI status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerAtCmdState 1.3.6.1.4.1.434.2.2.4.16.6.1.21
The status of the AT modem: on-hook (1) - modem not active dialing (2) - dialing a number answering (3) - accepting call from remote ringing (4) - incoming call present retrying (5) - awaiting new call attempt off-hook (6) - Modem active hanging-up (7) - Disconnecting from DCE
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on-hook(1), dialing(2), answering(3), ringing(4), retrying(5), off-hook(6), hanging-up(7)  

dialerV22BisDnaInfoTable 1.3.6.1.4.1.434.2.2.4.16.7
General Information Table for V22BISDNA dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerV22BisDnaInfoEntry

dialerV22BisDnaInfoEntry 1.3.6.1.4.1.434.2.2.4.16.7.1
The set of dialer configuration attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerV22BisDnaInfoEntry  

dialerV22BisDnaPortRef 1.3.6.1.4.1.434.2.2.4.16.7.1.1
The Port Number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerV22BisDnaPrimaryNum 1.3.6.1.4.1.434.2.2.4.16.7.1.2
The main telephone number stored in the dialer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerV22BisDnaSecondaryNum 1.3.6.1.4.1.434.2.2.4.16.7.1.3
The alternate telephone number stored in the dialer. This number is dialed if the main number is busy or if there is no answer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerV22BisDnaAnsEnable 1.3.6.1.4.1.434.2.2.4.16.7.1.4
States whether or not the dialer answers incoming calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FalseTrue  

dialerV22BisDnaRetryAllowed 1.3.6.1.4.1.434.2.2.4.16.7.1.5
Indicates whether or not the dialer will try to redial a number that is busy or does not answer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FalseTrue  

dialerV22BisDnaMaxRetries 1.3.6.1.4.1.434.2.2.4.16.7.1.6
Specifies how many times a number will be redialed if it is busy or otherwise unresponsive.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaCallProgress 1.3.6.1.4.1.434.2.2.4.16.7.1.7
Call progress tone detection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FalseTrue  

dialerV22BisDnaDecadic 1.3.6.1.4.1.434.2.2.4.16.7.1.8
Indicates whether Decadic dialing is active or not. Decadic dialing does the following: each digit you dial is subtracted from 10, and the result is the number actually dialed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FalseTrue  

dialerV22BisDnaMakeBreakRatio 1.3.6.1.4.1.434.2.2.4.16.7.1.9
Ratio for PULSE and DIAL make and break time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaRetryDelay 1.3.6.1.4.1.434.2.2.4.16.7.1.10
The amount of time in msecs between redial attempts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaMinDialDelay 1.3.6.1.4.1.434.2.2.4.16.7.1.11
The length of delay (msec) associated with a comma placed in a dialing command.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaWaitDialTone 1.3.6.1.4.1.434.2.2.4.16.7.1.12
The amount of time (msec) the modem waits when it encounters the wait for dial tone modifier in dial string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaWaitCarrier 1.3.6.1.4.1.434.2.2.4.16.7.1.13
The amount of time (msec) the modem waits for valid carrier after completing a dial.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaHndshkAbortTimer 1.3.6.1.4.1.434.2.2.4.16.7.1.14
The amount of time (sec) allowed before the call is aborted if DSR does not go ON.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaGuardTone 1.3.6.1.4.1.434.2.2.4.16.7.1.15
Indicates a guard tone frequency.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaPulseDelay 1.3.6.1.4.1.434.2.2.4.16.7.1.16
The delay (msec) between digits dialed on a pulse line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaDTMFDuration 1.3.6.1.4.1.434.2.2.4.16.7.1.17
The tone duration (msec) used in DMTF dialing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaDTMFDelay 1.3.6.1.4.1.434.2.2.4.16.7.1.18
The delay (msec) between digits dialed when in tone dial mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaDTMFLevel 1.3.6.1.4.1.434.2.2.4.16.7.1.19
The tone dialing level attenuation in dB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaTxLevel 1.3.6.1.4.1.434.2.2.4.16.7.1.20
The attenuation level (Db) on data transmission, once the handshake is completed with the remote modem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaRxLevel 1.3.6.1.4.1.434.2.2.4.16.7.1.21
Minimum acceptable receiver threshold value. This indicates whether a 3dB attenuation is used on the receive signal at line input.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FalseTrue  

dialerV22BisDnaRiNbr 1.3.6.1.4.1.434.2.2.4.16.7.1.22
The number of rings required before the modem answers, if it is set to auto-answer mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaDeltaRiDelay 1.3.6.1.4.1.434.2.2.4.16.7.1.23
delay in msecs before rings no longer occur.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaRiDtrDelay 1.3.6.1.4.1.434.2.2.4.16.7.1.24
Amount of delay in msec, before raising DTR when RING occurs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaDsrRtsDelay 1.3.6.1.4.1.434.2.2.4.16.7.1.25
Delay between arrival of DSR and activation of RTS circuit in msec.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaModemSpeed 1.3.6.1.4.1.434.2.2.4.16.7.1.26
Modem Speed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisDnaDtrSignal 1.3.6.1.4.1.434.2.2.4.16.7.1.27
DTR status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV22BisDnaDsrSignal 1.3.6.1.4.1.434.2.2.4.16.7.1.28
DSR status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV22BisDnaRiSignal 1.3.6.1.4.1.434.2.2.4.16.7.1.29
RI status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV22BisDnaCdSignal 1.3.6.1.4.1.434.2.2.4.16.7.1.30
Carrier detect status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV22BisDnaToneInd 1.3.6.1.4.1.434.2.2.4.16.7.1.31
Tone indication.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV22BisDnaDloInd 1.3.6.1.4.1.434.2.2.4.16.7.1.32
Dial line occupied indication.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV22BisDnaState 1.3.6.1.4.1.434.2.2.4.16.7.1.33
Status of the V22bis Dna modem: dialing-phone (1) - Dialing a number on the phone attached to the DNA phone plug. dialing-mdm (2) - Dialing a remote modem retrying (3) - Awaiting call attempt ringing (4) - Incoming call present line-busy (5) - Busy signal encountered off-hook (6) - Modem active on-hook (7) - Modem not active answering (8) - Accepting call from remote delaying (9) - Waiting for timer to expire voice-com (10) - the line is already used by a voice connection. handshaking (11) - Synchronizing calls with remote wait-ringback (12) - Awaiting remote response initialising (13) - initializing modem
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dialing-phone(1), dialing-mdm(2), retrying(3), ringing(4), line-busy(5), off-hook(6), on-hook(7), answering(8), delaying(9), voice-com(10), handshaking(11), wait-ringback(12), initialising(13)  

dialerV22BisImcInfoTable 1.3.6.1.4.1.434.2.2.4.16.8
General Information Table for V22BISIMC dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerV22BisImcInfoEntry

dialerV22BisImcInfoEntry 1.3.6.1.4.1.434.2.2.4.16.8.1
The set of dialer configuration attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerV22BisImcInfoEntry  

dialerV22BisImcPortRef 1.3.6.1.4.1.434.2.2.4.16.8.1.1
The Port Number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerV22BisImcPrimaryNum 1.3.6.1.4.1.434.2.2.4.16.8.1.2
The main telephone number stored in the dialer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerV22BisImcSecondaryNum 1.3.6.1.4.1.434.2.2.4.16.8.1.3
The alternate telephone number stored in the dialer. This number is dialed if the main number is busy or if there is no answer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerV22BisImcAnsEnable 1.3.6.1.4.1.434.2.2.4.16.8.1.4
States whether or not the dialer answers incoming calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FalseTrue  

dialerV22BisImcRetryAllowed 1.3.6.1.4.1.434.2.2.4.16.8.1.5
Indicates whether or not the dialer will try to redial a number that is busy or does not answer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FalseTrue  

dialerV22BisImcMaxRetries 1.3.6.1.4.1.434.2.2.4.16.8.1.6
Specifies how many times a number will be redialed if it is busy or otherwise unresponsive.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcCallProgress 1.3.6.1.4.1.434.2.2.4.16.8.1.7
Call progress tone detection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FalseTrue  

dialerV22BisImcDecadic 1.3.6.1.4.1.434.2.2.4.16.8.1.8
Indicates whether Decadic dialing is active or not. Decadic dialing does the following: each digit you dial is subtracted from 10, and the result is the number actually dialed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FalseTrue  

dialerV22BisImcMakeBreakRatio 1.3.6.1.4.1.434.2.2.4.16.8.1.9
Ratio of PULSE and DIAL make and break time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcRetryDelay 1.3.6.1.4.1.434.2.2.4.16.8.1.10
The amount of time in msecs between redial attempts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcMinDialDelay 1.3.6.1.4.1.434.2.2.4.16.8.1.11
The length of delay (msec) associated with a comma placed in a dialing command.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcWaitDialTone 1.3.6.1.4.1.434.2.2.4.16.8.1.12
The amount of time (msec) the modem waits when it encounters the wait for dial tone modifier in dial string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcWaitCarrier 1.3.6.1.4.1.434.2.2.4.16.8.1.13
The amount of time (msec) the modem waits for valid carrier after completing a dial.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcHndshkAbortTimer 1.3.6.1.4.1.434.2.2.4.16.8.1.14
The amount of time (sec) allowed before the call is aborted if DSR does not go ON.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcGuardTone 1.3.6.1.4.1.434.2.2.4.16.8.1.15
Indicates a guard tone frequency.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcPulseDelay 1.3.6.1.4.1.434.2.2.4.16.8.1.16
The delay between (msec) digits dialed on a pulse line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcDTMFDuration 1.3.6.1.4.1.434.2.2.4.16.8.1.17
The tone (msec) duration used in DMTF dialing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcDTMFDelay 1.3.6.1.4.1.434.2.2.4.16.8.1.18
The delay (msec) between digits dialed when in tone dial mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcDTMFLevel 1.3.6.1.4.1.434.2.2.4.16.8.1.19
The tone dialing level attenuation in dB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcTxLevel 1.3.6.1.4.1.434.2.2.4.16.8.1.20
The attenuation level (Db) on data transmission, once the handshake is completed with the remote modem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcRxLevel 1.3.6.1.4.1.434.2.2.4.16.8.1.21
Minimum acceptable receiver threshold value. This indicates whether a 3dB attenuation is used on the receive signal at line input.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcRiNbr 1.3.6.1.4.1.434.2.2.4.16.8.1.22
The numbet of rings required before the modem answers, if it is set to auto-answer mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcDeltaRiDelay 1.3.6.1.4.1.434.2.2.4.16.8.1.23
delay in msecs before rings no longer occur.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcRiDtrDelay 1.3.6.1.4.1.434.2.2.4.16.8.1.24
Amount of delay in msec, before raising DTR when RING occurs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcDsrRtsDelay 1.3.6.1.4.1.434.2.2.4.16.8.1.25
Delay between arrival of DSR and activation of RTS circuit in msec.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcModemSpeed 1.3.6.1.4.1.434.2.2.4.16.8.1.26
Modem Speed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV22BisImcDtrSignal 1.3.6.1.4.1.434.2.2.4.16.8.1.27
DTR status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV22BisImcDsrSignal 1.3.6.1.4.1.434.2.2.4.16.8.1.28
DSR status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV22BisImcRiSignal 1.3.6.1.4.1.434.2.2.4.16.8.1.29
RI status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV22BisImcCdSignal 1.3.6.1.4.1.434.2.2.4.16.8.1.30
Carrier Detect status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV22BisImcToneInd 1.3.6.1.4.1.434.2.2.4.16.8.1.31
Tone indication.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV22BisImcDloInd 1.3.6.1.4.1.434.2.2.4.16.8.1.32
Dial line occupied indication.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV22BisImcLineType 1.3.6.1.4.1.434.2.2.4.16.8.1.33
States whether the modem is connected to a Leased or Dial-Up phone line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dial(1), leased(2)  

dialerV22BisImcLeasedOpertn 1.3.6.1.4.1.434.2.2.4.16.8.1.34
This applies to Leased line type only. This field states whether the dialer will go off-hook in Originate or Answer mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER answer(1), originate(2)  

dialerV22BisImcSpeakerLevel 1.3.6.1.4.1.434.2.2.4.16.8.1.35
The volume level of the Eiconcard's speaker.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER low(1), high(2)  

dialerV22BisImcState 1.3.6.1.4.1.434.2.2.4.16.8.1.36
Status of the V22bis Imc modem: dialing-phone (1) - Dialing a number on the phone attached to the DNA phone plug. dialing-mdm (2) - Dialing a remote modem retrying (3) - Awaiting call attempt ringing (4) - Incoming call present line-busy (5) - Busy signal encountered off-hook (6) - Modem active on-hook (7) - Modem not active answering (8) - Accepting call from remote delaying (9) - Waiting for timer to expire voice-com (10) - the line is already used by a voice connection. handshaking (11) - Syncronizing calls with remote wait-ringback (12) - Awaiting remote response initialising (13) - initializing modem
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dialing-phone(1), dialing-mdm(2), retrying(3), ringing(4), line-busy(5), off-hook(6), on-hook(7), answering(8), delaying(9), voice-com(10), handshaking(11), wait-ringback(12), initialising(13)  

dialerV32BisInfoTable 1.3.6.1.4.1.434.2.2.4.16.9
General Information Table for V32Bis dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerV32BisInfoEntry

dialerV32BisInfoEntry 1.3.6.1.4.1.434.2.2.4.16.9.1
The set of dialer configuration attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerV32BisInfoEntry  

dialerV32BisPortRef 1.3.6.1.4.1.434.2.2.4.16.9.1.1
The Port Number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerV32BisPrimNum 1.3.6.1.4.1.434.2.2.4.16.9.1.2
The main telephone number stored in the dialer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerV32BisSecNum 1.3.6.1.4.1.434.2.2.4.16.9.1.3
The alternate telephone number stored in the dialer. This number is dialed if the main number is busy or if there is no answer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerV32BisOverrNum 1.3.6.1.4.1.434.2.2.4.16.9.1.4
Override number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerV32BisCurrNum 1.3.6.1.4.1.434.2.2.4.16.9.1.5
Current number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerV32BisPrimBitRate 1.3.6.1.4.1.434.2.2.4.16.9.1.6
Default bit rate for primary number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PrimBitRate  

dialerV32BisSecBitRate 1.3.6.1.4.1.434.2.2.4.16.9.1.7
Default bit rate for secondary number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PrimBitRate  

dialerV32BisOverrBitRate 1.3.6.1.4.1.434.2.2.4.16.9.1.8
Default bit rate for override number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PrimBitRate  

dialerV32BisCurrBitRate 1.3.6.1.4.1.434.2.2.4.16.9.1.9
Default bit rate for current number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PrimBitRate  

dialerV32BisPrimConfig 1.3.6.1.4.1.434.2.2.4.16.9.1.10
Dial modem primary configuration
Status: mandatory Access: read-only
OBJECT-TYPE    
  PrimCfg  

dialerV32BisSecConfig 1.3.6.1.4.1.434.2.2.4.16.9.1.11
Dial modem secondary configuration
Status: mandatory Access: read-only
OBJECT-TYPE    
  PrimCfg  

dialerV32BisOverrConfig 1.3.6.1.4.1.434.2.2.4.16.9.1.12
Dial modem override configuration
Status: mandatory Access: read-only
OBJECT-TYPE    
  PrimCfg  

dialerV32BisCurrConfig 1.3.6.1.4.1.434.2.2.4.16.9.1.13
Dial modem current configuration
Status: mandatory Access: read-only
OBJECT-TYPE    
  PrimCfg  

dialerV32BisCurrRetry 1.3.6.1.4.1.434.2.2.4.16.9.1.14
Current number of retries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisRingCount 1.3.6.1.4.1.434.2.2.4.16.9.1.15
Incoming ring counter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisAnsEnable 1.3.6.1.4.1.434.2.2.4.16.9.1.16
States whether or not the dialer answers incoming calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FalseTrue  

dialerV32BisDialMethod 1.3.6.1.4.1.434.2.2.4.16.9.1.17
The method used for dialing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dtmf(1), pulse(2)  

dialerV32BisRetry 1.3.6.1.4.1.434.2.2.4.16.9.1.18
Indicates whether or not the dialer will try to redial a number that is busy or does not answer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FalseTrue  

dialerV32BisCallFailure 1.3.6.1.4.1.434.2.2.4.16.9.1.19
Reason for last call failure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisCarrierDetect 1.3.6.1.4.1.434.2.2.4.16.9.1.20
Delay in msec to wait for verification of carrier detect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisCarrierWait 1.3.6.1.4.1.434.2.2.4.16.9.1.21
Delay in msec to wait for carrier detect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisHangupVerify 1.3.6.1.4.1.434.2.2.4.16.9.1.22
Delay in msec to wait to verify for hangup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisHangupSignal 1.3.6.1.4.1.434.2.2.4.16.9.1.23
Hangup signal state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisEnable  

dialerV32BisTxLevel 1.3.6.1.4.1.434.2.2.4.16.9.1.24
The attenuation level (Db) on data transmission, once the handshake is completed with the remote modem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisRxLevel 1.3.6.1.4.1.434.2.2.4.16.9.1.25
Minimum acceptable receiver threshold value. This indicates whether a 3dB attenuation is used on the receive signal at line input.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisGuardTone 1.3.6.1.4.1.434.2.2.4.16.9.1.26
Indicates a guard tone frequency.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisLeasedLine 1.3.6.1.4.1.434.2.2.4.16.9.1.27
Dial or leased line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER two-w-ll(1), four-w-ll(2)  

dialerV32BisLeaseMode 1.3.6.1.4.1.434.2.2.4.16.9.1.28
This applies to Leased line type only. This field states whether the dialer will go off-hook in Originate or Answer mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER answer(1), originate(2)  

dialerV32BisLLTxLevel 1.3.6.1.4.1.434.2.2.4.16.9.1.29
The attenuation level (Db) on data transmission once the handshake is completed with the remote modem (for leased line).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisLLConfig 1.3.6.1.4.1.434.2.2.4.16.9.1.30
Leased line configuration
Status: mandatory Access: read-only
OBJECT-TYPE    
  PrimCfg  

dialerV32BisLLBitRate 1.3.6.1.4.1.434.2.2.4.16.9.1.31
Leased line bit rate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PrimBitRate  

dialerV32BisCallingTone 1.3.6.1.4.1.434.2.2.4.16.9.1.32
Calling tone state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisEnable  

dialerV32BisAutoMode 1.3.6.1.4.1.434.2.2.4.16.9.1.33
Auto mode state (fallback/forward).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisEnable  

dialerV32BisRetryAllowed 1.3.6.1.4.1.434.2.2.4.16.9.1.34
Indicates whether or not the dialer will try to redial a number that is busy or does not answer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisEnable  

dialerV32BisMaxRetry 1.3.6.1.4.1.434.2.2.4.16.9.1.35
Specifies how many times a number will be redialed if it is busy or otherwise unresponsive.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisDialTone 1.3.6.1.4.1.434.2.2.4.16.9.1.36
The dial tone state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisEnable  

dialerV32BisDialToneWait 1.3.6.1.4.1.434.2.2.4.16.9.1.37
The amount of time (msec) the modem waits when it encounters the wait for dial tone modifier in dial string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisRetryWait 1.3.6.1.4.1.434.2.2.4.16.9.1.38
Retry timer delay.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisHangupWait 1.3.6.1.4.1.434.2.2.4.16.9.1.39
Hangup timer delay.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisDialPauseWait 1.3.6.1.4.1.434.2.2.4.16.9.1.40
maximum delay before dial.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisDeltaRiWait 1.3.6.1.4.1.434.2.2.4.16.9.1.41
Maximum delay (msec) between 2 rings.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisDTMFDuration 1.3.6.1.4.1.434.2.2.4.16.9.1.42
The tone duration (msec) used in DMTF dialing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisDTMFDelay 1.3.6.1.4.1.434.2.2.4.16.9.1.43
The delay (msec) between digits dialed when in tone dial mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisDTMFFreq1Level 1.3.6.1.4.1.434.2.2.4.16.9.1.44
DTMF high frequency power level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisDTMFFreq2Level 1.3.6.1.4.1.434.2.2.4.16.9.1.45
DTMF low frequency power level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisPulseMakeTime 1.3.6.1.4.1.434.2.2.4.16.9.1.46
Pulse make time (msec).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisPulseBreakTime 1.3.6.1.4.1.434.2.2.4.16.9.1.47
Pulse break time (msec).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisPulseDelay 1.3.6.1.4.1.434.2.2.4.16.9.1.48
Pulse interdigit delay (msec).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisSpeakerLevel 1.3.6.1.4.1.434.2.2.4.16.9.1.49
The volume level of the Eiconcard's speaker.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER low(1), high(2)  

dialerV32BisRiToAnswer 1.3.6.1.4.1.434.2.2.4.16.9.1.50
Number of rings befor answering.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerV32BisAnswerBitRate 1.3.6.1.4.1.434.2.2.4.16.9.1.51
Answer bit rate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PrimBitRate  

dialerV32BisAnswerConfig 1.3.6.1.4.1.434.2.2.4.16.9.1.52
Answer configuration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PrimCfg  

dialerV32BisRetrain 1.3.6.1.4.1.434.2.2.4.16.9.1.53
.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV32BisEqmLevel 1.3.6.1.4.1.434.2.2.4.16.9.1.54
.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disable(1), low-quality(2), medium-quality(3), high-quality(4)  

dialerV32BisRiOnOffDetect 1.3.6.1.4.1.434.2.2.4.16.9.1.55
Ring signal status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV32BisCdDetect 1.3.6.1.4.1.434.2.2.4.16.9.1.56
Carrier detect status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV32BisRingbackDetect 1.3.6.1.4.1.434.2.2.4.16.9.1.57
Ringback signal detect status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV32BisAnswerDetect 1.3.6.1.4.1.434.2.2.4.16.9.1.58
Answer tone detect status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV32BisBusyDetect 1.3.6.1.4.1.434.2.2.4.16.9.1.59
Busy tone detect status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV32BisDiscDetect 1.3.6.1.4.1.434.2.2.4.16.9.1.60
Disconnect detect status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV32BisCdSignal 1.3.6.1.4.1.434.2.2.4.16.9.1.61
CD signal status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV32BisDsrSignal 1.3.6.1.4.1.434.2.2.4.16.9.1.62
DSR signal status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OnOff  

dialerV32BisState 1.3.6.1.4.1.434.2.2.4.16.9.1.63
State of the V32bis dialer: m-closed (1) - Dialer not active m-opened (2) - No connection establised m-local-test (3) - Local analog loopback m-ringing (4) - Incoming call present m-dialing (5) - Dialing a number m-answering (6) - Call answer in progress m-originating (7) - Call originate in progress m-retrying (8) - Awaiting call attempt m-connected (9) - connection present m-retraining (10) - performing retrain m-remote-test (11) - Remote digital loopback m-remote-disc (12) - Remote has disconnected m-local-disc (13) - Local has disconnected m-hangup-idle (14) - Idle after hangup m-closing (15) - Awaiting local disconnect m-offhook-idle (16) - Modem goes off hook on command
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER m-closed(1), m-opened(2), m-local-test(3), m-ringing(4), m-dialing(5), m-answering(6), m-originating(7), m-retrying(8), m-connected(9), m-retraining(10), m-remote-test(11), m-remote-disc(12), m-local-disc(13), m-hangup-idle(14), m-closing(15), m-offhook-idle(16)  

dialerControlTable 1.3.6.1.4.1.434.2.2.4.16.10
The table for dynamic dialing entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerControlEntry

dialerControlEntry 1.3.6.1.4.1.434.2.2.4.16.10.1
The set of attributes for one entry per port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerControlEntry  

dialerCtrlPortRef 1.3.6.1.4.1.434.2.2.4.16.10.1.1
The Port number of the dialer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerCtrlAction 1.3.6.1.4.1.434.2.2.4.16.10.1.2
The Action states. exec (1) - This action executes the script file which would be set in dialerCtrlScriptFile. dial (2) - This action dials the number stored in dialerCtrlMainNumber. if dialerCtrlMainNumber is not set then the dialerCtrlPrimary number is dialed by the dialer. ISDN dialer dials the number stored by the card. hangup (3) - This action hangs-up the current connection. store (6) - This action stores the parameters in the card. ISDN dialer only.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER exec(1), dial(2), hangup(3), start(4), idle(5), store(6), other(7)  

dialerCtrlAnsEnable 1.3.6.1.4.1.434.2.2.4.16.10.1.3
States whether or not the dialer answers incoming calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FalseTrue  

dialerCtrlDirectDSROnOff 1.3.6.1.4.1.434.2.2.4.16.10.1.4
Defines the setting of the Data Rate Select signal. Setting this mib is valid only if the dialer type is Direct and the interface is RS-232.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OnOff  

dialerCtrlNumber 1.3.6.1.4.1.434.2.2.4.16.10.1.5
The primary Phone Number
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerCtrlScriptFile 1.3.6.1.4.1.434.2.2.4.16.10.1.6
The Complete path where the Dialer Script file resides.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..80)  

dialerCtrlActionState 1.3.6.1.4.1.434.2.2.4.16.10.1.7
The state of the action operation performed by the Agent as a result of setting the values to the dialerCtrlAction. The Management station will poll that variable after initiating an action. The value done(1) indicates that the action terminated successfully. The value failed(2) indicates that the action terminated with an error. The variable dialerCtrlActionError indicates the error code.
Status: mandatory Access: read-only
OBJECT-TYPE    
  ActionState  

dialerCtrlActionError 1.3.6.1.4.1.434.2.2.4.16.10.1.8
If the value is 0, this means no error. Otherwise, the value indicates the error code returned after the action operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerCtrlConfig 1.3.6.1.4.1.434.2.2.4.16.10.1.9
The config to which the V32 dialer will have to be set. This information is only used when using a V32 dialer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PrimCfg  

dialerCtrlBitRate 1.3.6.1.4.1.434.2.2.4.16.10.1.10
The Bit Rate to which the V32 dialer will have to be set. This information is only used when using a V32 dialer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PrimBitRate  

dialerCtrlType 1.3.6.1.4.1.434.2.2.4.16.10.1.11
The remote directory number type. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnDnType  

dialerCtrlPlan 1.3.6.1.4.1.434.2.2.4.16.10.1.12
The remote directory number plan. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnDnPlan  

dialerCtrlSub 1.3.6.1.4.1.434.2.2.4.16.10.1.13
The remote subaddress. When in the connected state, the remote subaddress dialer is displayed. Otherwise, the stored subaddress is displayed. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerCtrlSubType 1.3.6.1.4.1.434.2.2.4.16.10.1.14
The local subaddress type. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnSubType  

dialerCtrlTns 1.3.6.1.4.1.434.2.2.4.16.10.1.15
The string identifying the selected long distance carrier. In ISDN terms, it is called the Transit Network Selection. This string is usually made of 3 digits and is assigned by Bellcore. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

dialerCtrlNumberTemp 1.3.6.1.4.1.434.2.2.4.16.10.1.16
The temporary Phone Number. DEFINED ONLY FOR ISDN TESTS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..50)  

dialerCtrlDialMask 1.3.6.1.4.1.434.2.2.4.16.10.1.17
Read the mask state. DEFINED ONLY FOR TESTS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerCtrlCallSpeed 1.3.6.1.4.1.434.2.2.4.16.10.1.18
Read the mask state. DEFINED ONLY FOR TESTS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnStatusTable 1.3.6.1.4.1.434.2.2.4.16.11
The table for ISDN dialer Status.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerIsdnStatusEntry

dialerIsdnStatusEntry 1.3.6.1.4.1.434.2.2.4.16.11.1
The set of attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerIsdnStatusEntry  

dialerIsdnStatusPortRef 1.3.6.1.4.1.434.2.2.4.16.11.1.1
The port number for which isdn status is displayed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerIsdnStatusSwitchType 1.3.6.1.4.1.434.2.2.4.16.11.1.2
The current switch type in use for isdn.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ni1(1), nt(2), att(3), tr6(4), vn3(5), net3(6), tph(7), illegal(8)  

dialerIsdnStatusChType 1.3.6.1.4.1.434.2.2.4.16.11.1.3
The isdn channel type, B channel or D channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER b-channel(1), d-channel(2), illegal(3), unused(4)  

dialerIsdnStatusL1State 1.3.6.1.4.1.434.2.2.4.16.11.1.4
The current state of layer 1 subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER deactivated(1), await-info2(2), await-info4(3), activate(4), illegal(5)  

dialerIsdnStatusState 1.3.6.1.4.1.434.2.2.4.16.11.1.5
The current state of the ISDN dialer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER isdn-deact-closed(1), isdn-deact-opened(2), isdn-wait-act-closed(3), isdn-wait-act-opened(4), isdn-release-closed(5), isdn-release-opened(6), isdn-closed(7), isdn-opened(8), isdn-connecting(9), isdn-connected(10), isdn-ringing(11), isdn-disconnecting(12), isdn-closing(13), isdn-loopback(14), isdn-linking-deact(15), isdn-linking-act(16), isdn-test(17), isdn-linking-ring(18), isdn-illegal(19)  

dialerIsdnNI1BChTable 1.3.6.1.4.1.434.2.2.4.16.12
The table for the ISDN NI1 BChannel dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerIsdnNI1BChEntry

dialerIsdnNI1BChEntry 1.3.6.1.4.1.434.2.2.4.16.12.1
The set of attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerIsdnNI1BChEntry  

dialerIsdnNI1BChPortRef 1.3.6.1.4.1.434.2.2.4.16.12.1.1
The port number which is configured for NI1-BChannel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerIsdnNI1BChSpid 1.3.6.1.4.1.434.2.2.4.16.12.1.2
The Terminal's Service Profile IDentification.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnNI1BChSpidStatus 1.3.6.1.4.1.434.2.2.4.16.12.1.3
The current SPID status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnSpidStatus  

dialerIsdnNI1BChLocalDn 1.3.6.1.4.1.434.2.2.4.16.12.1.4
The local directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnNI1BChLocalSub 1.3.6.1.4.1.434.2.2.4.16.12.1.5
The local subaddress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnNI1BChTnsDigs 1.3.6.1.4.1.434.2.2.4.16.12.1.6
The string identifying the selected long distance carrier. In ISDN terms, it is called the Transit Network Selection. This string is usually made of 3 digits and is assigned by Bellcore.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

dialerIsdnNI1BChRemoteDn 1.3.6.1.4.1.434.2.2.4.16.12.1.7
When in the connected state, the number dialed is displayed. Otherwise, the stored number is displayed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnNI1BChRemoteSub 1.3.6.1.4.1.434.2.2.4.16.12.1.8
When in the connected state, the remote subaddress dialer is displayed. Otherwise, the stored subaddress is displayed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnNI1BChCallType 1.3.6.1.4.1.434.2.2.4.16.12.1.9
The current call type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnCallType  

dialerIsdnNI1BChCallSpeed 1.3.6.1.4.1.434.2.2.4.16.12.1.10
The current call speed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnCallSpeed  

dialerIsdnNI1BChBChannel 1.3.6.1.4.1.434.2.2.4.16.12.1.11
The current B channel connected to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnBChannels  

dialerIsdnNI1BChAnsEnable 1.3.6.1.4.1.434.2.2.4.16.12.1.12
Answer Enable Status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnAnsEnable  

dialerIsdnNI1BChCcState 1.3.6.1.4.1.434.2.2.4.16.12.1.13
The state of call control subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnNI1BCcState  

dialerIsdnNI1BChCcNbCause 1.3.6.1.4.1.434.2.2.4.16.12.1.14
The number of causes saved.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNI1BChCcCause 1.3.6.1.4.1.434.2.2.4.16.12.1.15
Last causes saved.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..10)  

dialerIsdnNI1BChL3State 1.3.6.1.4.1.434.2.2.4.16.12.1.16
The state of layer 3 subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnL3State  

dialerIsdnNI1BChL2State 1.3.6.1.4.1.434.2.2.4.16.12.1.17
The state of layer 2 subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnL2State  

dialerIsdnNI1BChTeiValue 1.3.6.1.4.1.434.2.2.4.16.12.1.18
The value of the terminal is dynamic TEI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNI1BChTeiStatus 1.3.6.1.4.1.434.2.2.4.16.12.1.19
The status of the terminal's dynamic TEI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTeiStatus  

dialerIsdnNI1BChLocalDnType 1.3.6.1.4.1.434.2.2.4.16.12.1.20
The local directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnDnType  

dialerIsdnNI1BChLocalDnPlan 1.3.6.1.4.1.434.2.2.4.16.12.1.21
The local directory number plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnDnPlan  

dialerIsdnNI1BChLocalSubType 1.3.6.1.4.1.434.2.2.4.16.12.1.22
The local subaddress type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnSubType  

dialerIsdnNI1BChTnsNetId 1.3.6.1.4.1.434.2.2.4.16.12.1.23
The transit network id.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTnsNetId  

dialerIsdnNI1BChTnsIdPlan 1.3.6.1.4.1.434.2.2.4.16.12.1.24
The transit network plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTnsIdPlan  

dialerIsdnNI1BChRemoteDnType 1.3.6.1.4.1.434.2.2.4.16.12.1.25
The remote directory number type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnDnType  

dialerIsdnNI1BChRemoteDnPlan 1.3.6.1.4.1.434.2.2.4.16.12.1.26
The remote directory number plan.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnDnPlan  

dialerIsdnNI1BChRemoteSubType 1.3.6.1.4.1.434.2.2.4.16.12.1.27
The local subaddress type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnSubType  

dialerIsdnNI1BChScrStatus 1.3.6.1.4.1.434.2.2.4.16.12.1.28
The status of call screening.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnScrStatus  

dialerIsdnNI1BChCallOpt 1.3.6.1.4.1.434.2.2.4.16.12.1.29
The current call option.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnCallOpt  

dialerIsdnNI1BChStoDefined 1.3.6.1.4.1.434.2.2.4.16.12.1.30
The validity of sto- elements.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnStoDefined  

dialerIsdnNI1BChStoDnType 1.3.6.1.4.1.434.2.2.4.16.12.1.31
The stored directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNI1BChStoDnPlan 1.3.6.1.4.1.434.2.2.4.16.12.1.32
The stored directory number plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNI1BChStoDn 1.3.6.1.4.1.434.2.2.4.16.12.1.33
The stored directory number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnNI1BChStoSubType 1.3.6.1.4.1.434.2.2.4.16.12.1.34
The stored subaddress type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNI1BChStoSub 1.3.6.1.4.1.434.2.2.4.16.12.1.35
The stored subaddress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnNI1BChStoTnsNetId 1.3.6.1.4.1.434.2.2.4.16.12.1.36
The stored transit network id.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNI1BChStoTnsPlan 1.3.6.1.4.1.434.2.2.4.16.12.1.37
The stored transit network plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNI1BChStoDigs 1.3.6.1.4.1.434.2.2.4.16.12.1.38
The stored transit network address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

dialerIsdnNI1BChStoBcType 1.3.6.1.4.1.434.2.2.4.16.12.1.39
The stored bearer cap. type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNI1BChStoBcOpt 1.3.6.1.4.1.434.2.2.4.16.12.1.40
The stored bearer cap. option.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNI1DChTable 1.3.6.1.4.1.434.2.2.4.16.13
The table for the ISDN NI1 DChannel dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerIsdnNI1DChEntry

dialerIsdnNI1DChEntry 1.3.6.1.4.1.434.2.2.4.16.13.1
The set of attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerIsdnNI1DChEntry  

dialerIsdnNI1DChPortRef 1.3.6.1.4.1.434.2.2.4.16.13.1.1
The port number configured for the NI1 DChannel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerIsdnNI1DChTeiValue 1.3.6.1.4.1.434.2.2.4.16.13.1.2
The static TEI value on the D Channel for data communications.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNI1DChTeiStatus 1.3.6.1.4.1.434.2.2.4.16.13.1.3
The status of TEI - always ASSIGNED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTeiStatus  

dialerIsdnNI1DChL2State 1.3.6.1.4.1.434.2.2.4.16.13.1.4
The current layer 2 state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnL2State  

dialerIsdnNI1DChP3State 1.3.6.1.4.1.434.2.2.4.16.13.1.5
The current Packet layer state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnP3State  

dialerIsdnNI1DChActState 1.3.6.1.4.1.434.2.2.4.16.13.1.6
The current activation FSM state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnActState  

dialerIsdnTR6BChTable 1.3.6.1.4.1.434.2.2.4.16.14
The table for the ISDN TR6 BChannel dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerIsdnTR6BChEntry

dialerIsdnTR6BChEntry 1.3.6.1.4.1.434.2.2.4.16.14.1
The set of attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerIsdnTR6BChEntry  

dialerIsdnTR6BChPortRef 1.3.6.1.4.1.434.2.2.4.16.14.1.1
The port number for which the 1TR6 BChannel info is displayed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerIsdnTR6BChLocalDn 1.3.6.1.4.1.434.2.2.4.16.14.1.2
The local directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnTR6BChRemoteDn 1.3.6.1.4.1.434.2.2.4.16.14.1.3
When in the connected state, the number dialed is displayed. Otherwise, the stored number is displayed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnTR6BChCallType 1.3.6.1.4.1.434.2.2.4.16.14.1.4
The current call type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnCallType  

dialerIsdnTR6BChCallSpeed 1.3.6.1.4.1.434.2.2.4.16.14.1.5
The current call speed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnCallSpeed  

dialerIsdnTR6BChBChannel 1.3.6.1.4.1.434.2.2.4.16.14.1.6
The current B Channel connected to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnBChannels  

dialerIsdnTR6BChAnsEnable 1.3.6.1.4.1.434.2.2.4.16.14.1.7
Answer enable status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnAnsEnable  

dialerIsdnTR6BChCcState 1.3.6.1.4.1.434.2.2.4.16.14.1.8
The state of call control subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTR6BCcState  

dialerIsdnTR6BChCcNbCause 1.3.6.1.4.1.434.2.2.4.16.14.1.9
The number of causes saved.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTR6BChCcCause 1.3.6.1.4.1.434.2.2.4.16.14.1.10
Last causes saved.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..10)  

dialerIsdnTR6BChL3State 1.3.6.1.4.1.434.2.2.4.16.14.1.11
The state of layer 3 subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnL3State  

dialerIsdnTR6BChL2State 1.3.6.1.4.1.434.2.2.4.16.14.1.12
The state of layer 2 subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnL2State  

dialerIsdnTR6BChLocalDnType 1.3.6.1.4.1.434.2.2.4.16.14.1.13
The local directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnDnType  

dialerIsdnTR6BChLocalDnPlan 1.3.6.1.4.1.434.2.2.4.16.14.1.14
The local directory number plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnDnPlan  

dialerIsdnTR6BChRemoteDnType 1.3.6.1.4.1.434.2.2.4.16.14.1.15
The remote directory number type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnDnType  

dialerIsdnTR6BChRemoteDnPlan 1.3.6.1.4.1.434.2.2.4.16.14.1.16
The remote directory number plan.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnDnPlan  

dialerIsdnTR6BChScrStatus 1.3.6.1.4.1.434.2.2.4.16.14.1.17
The status of call screening.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnScrStatus  

dialerIsdnTR6BChCallOpt 1.3.6.1.4.1.434.2.2.4.16.14.1.18
The current call option.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnCallOpt  

dialerIsdnTR6BChTeiValue 1.3.6.1.4.1.434.2.2.4.16.14.1.19
The static TEI value on the D Channel for data communications.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTR6BChTeiStatus 1.3.6.1.4.1.434.2.2.4.16.14.1.20
The status of TEI - always ASSIGNED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTeiStatus  

dialerIsdnTR6BChStoDefined 1.3.6.1.4.1.434.2.2.4.16.14.1.21
The validity of sto- elements.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnStoDefined  

dialerIsdnTR6BChStoDnType 1.3.6.1.4.1.434.2.2.4.16.14.1.22
The stored directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTR6BChStoDnPlan 1.3.6.1.4.1.434.2.2.4.16.14.1.23
The stored directory number plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTR6BChStoDn 1.3.6.1.4.1.434.2.2.4.16.14.1.24
The stored directory number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnTR6BChStoBcType 1.3.6.1.4.1.434.2.2.4.16.14.1.25
The stored bearer cap. type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTR6BChStoBcOpt 1.3.6.1.4.1.434.2.2.4.16.14.1.26
The stored bearer cap. option.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnVN3BChTable 1.3.6.1.4.1.434.2.2.4.16.15
The table for the ISDN VN3 BChannel dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerIsdnVN3BChEntry

dialerIsdnVN3BChEntry 1.3.6.1.4.1.434.2.2.4.16.15.1
The set of attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerIsdnVN3BChEntry  

dialerIsdnVN3BChPortRef 1.3.6.1.4.1.434.2.2.4.16.15.1.1
The port number for which the VN3 BChannel info is displayed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerIsdnVN3BChLocalDnType 1.3.6.1.4.1.434.2.2.4.16.15.1.2
The local directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnDnType  

dialerIsdnVN3BChLocalDnPlan 1.3.6.1.4.1.434.2.2.4.16.15.1.3
The local directory number plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnDnPlan  

dialerIsdnVN3BChLocalDn 1.3.6.1.4.1.434.2.2.4.16.15.1.4
The local directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnVN3BChLocalSubType 1.3.6.1.4.1.434.2.2.4.16.15.1.5
The local subaddress type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnSubType  

dialerIsdnVN3BChLocalSub 1.3.6.1.4.1.434.2.2.4.16.15.1.6
The local directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnVN3BChRemoteDnType 1.3.6.1.4.1.434.2.2.4.16.15.1.7
The local directory number type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnDnType  

dialerIsdnVN3BChRemoteDnPlan 1.3.6.1.4.1.434.2.2.4.16.15.1.8
The local directory number plan.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnDnPlan  

dialerIsdnVN3BChRemoteDn 1.3.6.1.4.1.434.2.2.4.16.15.1.9
The local directory number type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnVN3BChRemoteSubType 1.3.6.1.4.1.434.2.2.4.16.15.1.10
The local subaddress type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnSubType  

dialerIsdnVN3BChRemoteSub 1.3.6.1.4.1.434.2.2.4.16.15.1.11
The local directory number type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnVN3BChCallType 1.3.6.1.4.1.434.2.2.4.16.15.1.12
The current call type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnCallType  

dialerIsdnVN3BChCallSpeed 1.3.6.1.4.1.434.2.2.4.16.15.1.13
The current call speed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnCallSpeed  

dialerIsdnVN3BChBChannel 1.3.6.1.4.1.434.2.2.4.16.15.1.14
The current B Channel connected to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnBChannels  

dialerIsdnVN3BChAnsEnable 1.3.6.1.4.1.434.2.2.4.16.15.1.15
Answer enable status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnAnsEnable  

dialerIsdnVN3BChScrStatus 1.3.6.1.4.1.434.2.2.4.16.15.1.16
The status of call screening.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnScrStatus  

dialerIsdnVN3BChCallOpt 1.3.6.1.4.1.434.2.2.4.16.15.1.17
The current call option.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnCallOpt  

dialerIsdnVN3BChCcState 1.3.6.1.4.1.434.2.2.4.16.15.1.18
The state of call control subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnVN3BCcState  

dialerIsdnVN3BChCcNbCause 1.3.6.1.4.1.434.2.2.4.16.15.1.19
The number of causes saved.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnVN3BChCcCause 1.3.6.1.4.1.434.2.2.4.16.15.1.20
Last causes saved.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..10)  

dialerIsdnVN3BChL3State 1.3.6.1.4.1.434.2.2.4.16.15.1.21
The state of layer 3 subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnL3State  

dialerIsdnVN3BChL2State 1.3.6.1.4.1.434.2.2.4.16.15.1.22
The state of layer 2 subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnL2State  

dialerIsdnVN3BChTeiValue 1.3.6.1.4.1.434.2.2.4.16.15.1.23
The static TEI value on the D Channel for data communications.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnVN3BChTeiStatus 1.3.6.1.4.1.434.2.2.4.16.15.1.24
The status of TEI - always ASSIGNED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTeiStatus  

dialerIsdnVN3BChStoDefined 1.3.6.1.4.1.434.2.2.4.16.15.1.25
The validity of sto- elements.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnStoDefined  

dialerIsdnVN3BChStoDnType 1.3.6.1.4.1.434.2.2.4.16.15.1.26
The stored directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnVN3BChStoDnPlan 1.3.6.1.4.1.434.2.2.4.16.15.1.27
The stored directory number plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnVN3BChStoDn 1.3.6.1.4.1.434.2.2.4.16.15.1.28
The stored directory number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnVN3BChStoSubType 1.3.6.1.4.1.434.2.2.4.16.15.1.29
The stored subaddress type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnVN3BChStoSub 1.3.6.1.4.1.434.2.2.4.16.15.1.30
The stored subaddress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnVN3BChStoBcType 1.3.6.1.4.1.434.2.2.4.16.15.1.31
The stored bearer cap type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnVN3BChStoBcOpt 1.3.6.1.4.1.434.2.2.4.16.15.1.32
The stored bearer cap option.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnVN3DChTable 1.3.6.1.4.1.434.2.2.4.16.16
The table for the ISDN VN3 DChannel dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerIsdnVN3DChEntry

dialerIsdnVN3DChEntry 1.3.6.1.4.1.434.2.2.4.16.16.1
The set of attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerIsdnVN3DChEntry  

dialerIsdnVN3DChPortRef 1.3.6.1.4.1.434.2.2.4.16.16.1.1
The port number for which the VN3 DChannel info is displayed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerIsdnVN3DChTeiValue 1.3.6.1.4.1.434.2.2.4.16.16.1.2
The static TEI value on the D Channel for data communications.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnVN3DChTeiStatus 1.3.6.1.4.1.434.2.2.4.16.16.1.3
The status of TEI - always ASSIGNED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTeiStatus  

dialerIsdnVN3DChL2State 1.3.6.1.4.1.434.2.2.4.16.16.1.4
The state of layer 2 subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnL2State  

dialerIsdnVN3DChP3State 1.3.6.1.4.1.434.2.2.4.16.16.1.5
The current Packet layer state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnP3State  

dialerIsdnNET3BChTable 1.3.6.1.4.1.434.2.2.4.16.17
The table for the ISDN NET3 BChannel dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerIsdnNET3BChEntry

dialerIsdnNET3BChEntry 1.3.6.1.4.1.434.2.2.4.16.17.1
The set of attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerIsdnNET3BChEntry  

dialerIsdnNET3BChPortRef 1.3.6.1.4.1.434.2.2.4.16.17.1.1
The port number for which the NET3 BChannel info is displayed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerIsdnNET3BChLocalDnType 1.3.6.1.4.1.434.2.2.4.16.17.1.2
The local directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnDnType  

dialerIsdnNET3BChLocalDnPlan 1.3.6.1.4.1.434.2.2.4.16.17.1.3
The local directory number plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnDnPlan  

dialerIsdnNET3BChLocalDn 1.3.6.1.4.1.434.2.2.4.16.17.1.4
The local directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnNET3BChLocalSubType 1.3.6.1.4.1.434.2.2.4.16.17.1.5
The local subaddress type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnSubType  

dialerIsdnNET3BChLocalSub 1.3.6.1.4.1.434.2.2.4.16.17.1.6
The local directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnNET3BChRemoteDnType 1.3.6.1.4.1.434.2.2.4.16.17.1.7
The local directory number type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnDnType  

dialerIsdnNET3BChRemoteDnPlan 1.3.6.1.4.1.434.2.2.4.16.17.1.8
The local directory number plan.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnDnPlan  

dialerIsdnNET3BChRemoteDn 1.3.6.1.4.1.434.2.2.4.16.17.1.9
The local directory number type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnNET3BChRemoteSubType 1.3.6.1.4.1.434.2.2.4.16.17.1.10
The local subaddress type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnSubType  

dialerIsdnNET3BChRemoteSub 1.3.6.1.4.1.434.2.2.4.16.17.1.11
The local directory number type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnNET3BChCallType 1.3.6.1.4.1.434.2.2.4.16.17.1.12
The current call type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnCallType  

dialerIsdnNET3BChCallSpeed 1.3.6.1.4.1.434.2.2.4.16.17.1.13
The current call speed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnCallSpeed  

dialerIsdnNET3BChBChannel 1.3.6.1.4.1.434.2.2.4.16.17.1.14
The current B Channel connected to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnBChannels  

dialerIsdnNET3BChAnsEnable 1.3.6.1.4.1.434.2.2.4.16.17.1.15
Answer enable status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnAnsEnable  

dialerIsdnNET3BChTnsNetId 1.3.6.1.4.1.434.2.2.4.16.17.1.16
The transit network id.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTnsNetId  

dialerIsdnNET3BChTnsIdPlan 1.3.6.1.4.1.434.2.2.4.16.17.1.17
The transit network plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTnsIdPlan  

dialerIsdnNET3BChTnsDigs 1.3.6.1.4.1.434.2.2.4.16.17.1.18
The string identifying the selected long distance carrier. In ISDN terms, it is called the Transit Network Selection. This string is usually made of 3 digits and is assigned by Bellcore.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

dialerIsdnNET3BChScrStatus 1.3.6.1.4.1.434.2.2.4.16.17.1.19
The status of call screening.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnScrStatus  

dialerIsdnNET3BChCallOpt 1.3.6.1.4.1.434.2.2.4.16.17.1.20
The current call option.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnCallOpt  

dialerIsdnNET3BChCcState 1.3.6.1.4.1.434.2.2.4.16.17.1.21
The state of call control subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnNET3BCcState  

dialerIsdnNET3BChCcNbCause 1.3.6.1.4.1.434.2.2.4.16.17.1.22
The number of causes saved.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNET3BChCcCause 1.3.6.1.4.1.434.2.2.4.16.17.1.23
Last causes saved.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..10)  

dialerIsdnNET3BChL3State 1.3.6.1.4.1.434.2.2.4.16.17.1.24
The state of layer 3 subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnL3State  

dialerIsdnNET3BChL2State 1.3.6.1.4.1.434.2.2.4.16.17.1.25
The state of layer 2 subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnL2State  

dialerIsdnNET3BChTeiValue 1.3.6.1.4.1.434.2.2.4.16.17.1.26
The static TEI value on the D Channel for data communications.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNET3BChTeiStatus 1.3.6.1.4.1.434.2.2.4.16.17.1.27
The status of TEI - always ASSIGNED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTeiStatus  

dialerIsdnNET3BChStoDefined 1.3.6.1.4.1.434.2.2.4.16.17.1.28
The validity of sto- elements.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnStoDefined  

dialerIsdnNET3BChStoDnType 1.3.6.1.4.1.434.2.2.4.16.17.1.29
The stored directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNET3BChStoDnPlan 1.3.6.1.4.1.434.2.2.4.16.17.1.30
The stored directory number plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNET3BChStoDn 1.3.6.1.4.1.434.2.2.4.16.17.1.31
The stored directory number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnNET3BChStoSubType 1.3.6.1.4.1.434.2.2.4.16.17.1.32
The stored subaddress type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNET3BChStoSub 1.3.6.1.4.1.434.2.2.4.16.17.1.33
The stored subaddress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnNET3BChStoTnsNetId 1.3.6.1.4.1.434.2.2.4.16.17.1.34
The stored transit network id.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNET3BChStoTnsPlan 1.3.6.1.4.1.434.2.2.4.16.17.1.35
The stored transit network plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNET3BChStoDigs 1.3.6.1.4.1.434.2.2.4.16.17.1.36
The stored transit network address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

dialerIsdnNET3BChStoBcType 1.3.6.1.4.1.434.2.2.4.16.17.1.37
The stored bearer cap. type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnNET3BChStoBcOpt 1.3.6.1.4.1.434.2.2.4.16.17.1.38
The stored bearer cap. option.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTPHBChTable 1.3.6.1.4.1.434.2.2.4.16.18
The table for the ISDN TPH BChannel dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerIsdnTPHBChEntry

dialerIsdnTPHBChEntry 1.3.6.1.4.1.434.2.2.4.16.18.1
The set of attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerIsdnTPHBChEntry  

dialerIsdnTPHBChPortRef 1.3.6.1.4.1.434.2.2.4.16.18.1.1
The port number for which the TPH BChannel info is displayed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerIsdnTPHBChLocalDnType 1.3.6.1.4.1.434.2.2.4.16.18.1.2
The local directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnDnType  

dialerIsdnTPHBChLocalDnPlan 1.3.6.1.4.1.434.2.2.4.16.18.1.3
The local directory number plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnDnPlan  

dialerIsdnTPHBChLocalDn 1.3.6.1.4.1.434.2.2.4.16.18.1.4
The local directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnTPHBChLocalSubType 1.3.6.1.4.1.434.2.2.4.16.18.1.5
The local subaddress type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnSubType  

dialerIsdnTPHBChLocalSub 1.3.6.1.4.1.434.2.2.4.16.18.1.6
The local directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnTPHBChRemoteDnType 1.3.6.1.4.1.434.2.2.4.16.18.1.7
The local directory number type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnDnType  

dialerIsdnTPHBChRemoteDnPlan 1.3.6.1.4.1.434.2.2.4.16.18.1.8
The local directory number plan.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnDnPlan  

dialerIsdnTPHBChRemoteDn 1.3.6.1.4.1.434.2.2.4.16.18.1.9
The local directory number type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnTPHBChRemoteSubType 1.3.6.1.4.1.434.2.2.4.16.18.1.10
The local subaddress type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnSubType  

dialerIsdnTPHBChRemoteSub 1.3.6.1.4.1.434.2.2.4.16.18.1.11
The local directory number type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnTPHBChCallType 1.3.6.1.4.1.434.2.2.4.16.18.1.12
The current call type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnCallType  

dialerIsdnTPHBChCallSpeed 1.3.6.1.4.1.434.2.2.4.16.18.1.13
The current call speed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IsdnCallSpeed  

dialerIsdnTPHBChBChannel 1.3.6.1.4.1.434.2.2.4.16.18.1.14
The current B Channel connected to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnBChannels  

dialerIsdnTPHBChAnsEnable 1.3.6.1.4.1.434.2.2.4.16.18.1.15
Answer enable status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnAnsEnable  

dialerIsdnTPHBChScrStatus 1.3.6.1.4.1.434.2.2.4.16.18.1.16
The status of call screening.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnScrStatus  

dialerIsdnTPHBChCallOpt 1.3.6.1.4.1.434.2.2.4.16.18.1.17
The current call option.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnCallOpt  

dialerIsdnTPHBChCcState 1.3.6.1.4.1.434.2.2.4.16.18.1.18
The state of call control subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTPHBCcState  

dialerIsdnTPHBChCcNbCause 1.3.6.1.4.1.434.2.2.4.16.18.1.19
The number of causes saved.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTPHBChCcCause 1.3.6.1.4.1.434.2.2.4.16.18.1.20
Last causes saved.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..10)  

dialerIsdnTPHBChL3State 1.3.6.1.4.1.434.2.2.4.16.18.1.21
The state of layer 3 subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnL3State  

dialerIsdnTPHBChL2State 1.3.6.1.4.1.434.2.2.4.16.18.1.22
The state of layer 2 subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnL2State  

dialerIsdnTPHBChTeiValue 1.3.6.1.4.1.434.2.2.4.16.18.1.23
The static TEI value on the D Channel for data communications.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTPHBChTeiStatus 1.3.6.1.4.1.434.2.2.4.16.18.1.24
The status of TEI - always ASSIGNED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTeiStatus  

dialerIsdnTPHBChStoDefined 1.3.6.1.4.1.434.2.2.4.16.18.1.25
The validity of sto- elements.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnStoDefined  

dialerIsdnTPHBChStoDnType 1.3.6.1.4.1.434.2.2.4.16.18.1.26
The stored directory number type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTPHBChStoDnPlan 1.3.6.1.4.1.434.2.2.4.16.18.1.27
The stored directory number plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTPHBChStoDn 1.3.6.1.4.1.434.2.2.4.16.18.1.28
The stored directory number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnTPHBChStoSubType 1.3.6.1.4.1.434.2.2.4.16.18.1.29
The stored subaddress type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTPHBChStoSub 1.3.6.1.4.1.434.2.2.4.16.18.1.30
The stored subaddress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..21)  

dialerIsdnTPHBChStoBcType 1.3.6.1.4.1.434.2.2.4.16.18.1.31
The stored bearer cap. type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTPHBChStoBcOpt 1.3.6.1.4.1.434.2.2.4.16.18.1.32
The stored bearer cap. option.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTPHDChTable 1.3.6.1.4.1.434.2.2.4.16.19
The table for the ISDN TPH DChannel dialer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DialerIsdnTPHDChEntry

dialerIsdnTPHDChEntry 1.3.6.1.4.1.434.2.2.4.16.19.1
The set of attributes for one port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DialerIsdnTPHDChEntry  

dialerIsdnTPHDChPortRef 1.3.6.1.4.1.434.2.2.4.16.19.1.1
The port number for which the TPH DChannel info is displayed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortRef  

dialerIsdnTPHDChTeiValue 1.3.6.1.4.1.434.2.2.4.16.19.1.2
The static TEI value on the D Channel for data communications.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dialerIsdnTPHDChTeiStatus 1.3.6.1.4.1.434.2.2.4.16.19.1.3
The status of TEI - always ASSIGNED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnTeiStatus  

dialerIsdnTPHDChL2State 1.3.6.1.4.1.434.2.2.4.16.19.1.4
The state of layer 2 subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnL2State  

dialerIsdnTPHDChP3State 1.3.6.1.4.1.434.2.2.4.16.19.1.5
The current Packet layer state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IsdnP3State