EGRESSACL-MIB

File: EGRESSACL-MIB.mib (104576 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC RFC1213-MIB
SNMP-FRAMEWORK-MIB Q-BRIDGE-MIB IPV6-TC
DLINK-ID-REC-MIB

Imported symbols

Counter32 Counter64 TimeTicks
NOTIFICATION-TYPE MODULE-IDENTITY OBJECT-TYPE
IpAddress Unsigned32 MacAddress
RowStatus DisplayString SnmpAdminString
PortList VlanIdOrNone Ipv6Address
dlink-common-mgmt

Defined Types

SwEgressACLEthernetEntry  
SEQUENCE    
  swEgressACLEthernetProfileID INTEGER
  swEgressACLEthernetRowStatus RowStatus
  swEgressACLEthernetProfileName DisplayString
  swEgressACLEthernetUsevlan INTEGER
  swEgressACLEthernetVlanMask OCTET STRING
  swEgressACLEthernetUse8021p INTEGER
  swEgressACLEthernetUseEthernetType INTEGER
  swEgressACLEthernetMacAddrMaskState INTEGER
  swEgressACLEthernetSrcMacAddrMask MacAddress
  swEgressACLEthernetDstMacAddrMask MacAddress
  swEgressACLEthernetUnusedRuleEntries INTEGER

SwEgressACLIpEntry  
SEQUENCE    
  swEgressACLIpProfileID INTEGER
  swEgressACLIpRowStatus RowStatus
  swEgressACLIpProfileName DisplayString
  swEgressACLIpUsevlan INTEGER
  swEgressACLIpVlanMask OCTET STRING
  swEgressACLIpIpAddrMaskState INTEGER
  swEgressACLIpSrcIpAddrMask IpAddress
  swEgressACLIpDstIpAddrMask IpAddress
  swEgressACLIpUseDSCP INTEGER
  swEgressACLIpUseProtoType INTEGER
  swEgressACLIpIcmpOption INTEGER
  swEgressACLIpIgmpOption INTEGER
  swEgressACLIpTcpOption INTEGER
  swEgressACLIpUdpOption INTEGER
  swEgressACLIpTCPorUDPSrcPortMask OCTET STRING
  swEgressACLIpTCPorUDPDstPortMask OCTET STRING
  swEgressACLIpTCPFlagBit INTEGER
  swEgressACLIpTCPFlagBitMask INTEGER
  swEgressACLIpProtoIDOption INTEGER
  swEgressACLIpProtoID INTEGER
  swEgressACLIpProtoIDMask OCTET STRING
  swEgressACLIpUnusedRuleEntries INTEGER

SwEgressACLIpv6MaskEntry  
SEQUENCE    
  swEgressACLIpv6MaskProfileID INTEGER
  swEgressACLIpv6MaskRowStatus RowStatus
  swEgressACLIpv6MaskProfileName DisplayString
  swEgressACLIpv6MaskClass INTEGER
  swEgressACLIpv6IpAddrMaskState INTEGER
  swEgressACLIpv6MaskSrcIpv6Mask Ipv6Address
  swEgressACLIpv6MaskDstIpv6Mask Ipv6Address
  swEgressACLIpv6MaskUseProtoType INTEGER
  swEgressACLIpv6MaskIcmpOption INTEGER
  swEgressACLIpv6MaskTcpOption INTEGER
  swEgressACLIpv6MaskUdpOption INTEGER
  swEgressACLIpv6MaskTCPorUDPSrcPortMask OCTET STRING
  swEgressACLIpv6MaskTCPorUDPDstPortMask OCTET STRING
  swEgressACLIpv6MaskUnusedRuleEntries INTEGER

SwEgressACLEtherRuleEntry  
SEQUENCE    
  swEgressACLEtherRuleProfileID INTEGER
  swEgressACLEtherRuleAccessID INTEGER
  swEgressACLEtherRuleRowStatus RowStatus
  swEgressACLEtherRuleMatchVID VlanIdOrNone
  swEgressACLEtherRuleMatchVlanMask OCTET STRING
  swEgressACLEtherRuleSrcMacAddress MacAddress
  swEgressACLEtherRuleMaskSrcMacAddress MacAddress
  swEgressACLEtherRuleDstMacAddress MacAddress
  swEgressACLEtherRuleMaskDstMacAddress MacAddress
  swEgressACLEtherRule8021P INTEGER
  swEgressACLEtherRuleEtherType OCTET STRING
  swEgressACLEtherRuleVID VlanIdOrNone
  swEgressACLEtherRulePort INTEGER
  swEgressACLEtherRulePortGroup INTEGER
  swEgressACLEtherRulePermit INTEGER
  swEgressACLEtherRuleEnableReplacePriority INTEGER
  swEgressACLEtherRuleReplacePriority INTEGER
  swEgressACLEtherRuleEnableReplaceDscp INTEGER
  swEgressACLEtherRuleReplaceDscp INTEGER
  swEgressAclEtherRuleTimeRangeName DisplayString

SwEgressACLIpRuleEntry  
SEQUENCE    
  swEgressACLIpRuleProfileID INTEGER
  swEgressACLIpRuleAccessID INTEGER
  swEgressACLIpRuleRowStatus RowStatus
  swEgressACLIpRuleMatchVID VlanIdOrNone
  swEgressACLIpMatchVlanMask OCTET STRING
  swEgressACLIpRuleSrcIpaddress IpAddress
  swEgressACLIpRuleMaskSrcIpaddress IpAddress
  swEgressACLIpRuleDstIpaddress IpAddress
  swEgressACLIpRuleMaskDstIpaddress IpAddress
  swEgressACLIpRuleDscp INTEGER
  swEgressACLIpRuleProtocol INTEGER
  swEgressACLIpRuleType INTEGER
  swEgressACLIpRuleCode INTEGER
  swEgressACLIpRuleSrcPort INTEGER
  swEgressACLIpRuleMaskSrcPort OCTET STRING
  swEgressACLIpRuleDstPort INTEGER
  swEgressACLIpRuleMaskDstPort OCTET STRING
  swEgressACLIpRuleFlagBits INTEGER
  swEgressACLIpRuleProtoID INTEGER
  swEgressACLIpRuleUserDefine OCTET STRING
  swEgressACLIpRuleUserDefineMask OCTET STRING
  swEgressACLIpRuleVID VlanIdOrNone
  swEgressACLIpRulePort INTEGER
  swEgressACLIpRulePortGroup INTEGER
  swEgressACLIpRulePermit INTEGER
  swEgressACLIpRuleEnableReplacePriority INTEGER
  swEgressACLIpRuleReplacePriority INTEGER
  swEgressACLIpRuleEnableReplaceDscp INTEGER
  swEgressACLIpRuleReplaceDscp INTEGER
  swEgressAclIpRuleTimeRangeName DisplayString

SwEgressACLIpv6RuleEntry  
SEQUENCE    
  swEgressACLIpv6RuleProfileID INTEGER
  swEgressACLIpv6RuleAccessID INTEGER
  swEgressACLIpv6RuleRowStatus RowStatus
  swEgressACLIpv6RuleClass INTEGER
  swEgressACLIpv6RuleSrcIpv6Addr Ipv6Address
  swEgressACLIpv6RuleMaskSrcIpv6Addr Ipv6Address
  swEgressACLIpv6RuleDstIpv6Addr Ipv6Address
  swEgressACLIpv6RuleMaskDstIpv6Addr Ipv6Address
  swEgressACLIpv6RuleProtocol INTEGER
  swEgressACLIpv6RuleType INTEGER
  swEgressACLIpv6RuleCode INTEGER
  swEgressACLIpv6RuleSrcPort INTEGER
  swEgressACLIpv6RuleMaskSrcPort OCTET STRING
  swEgressACLIpv6RuleDstPort INTEGER
  swEgressACLIpv6RuleMaskDstPort OCTET STRING
  swEgressACLIpv6RuleVID VlanIdOrNone
  swEgressACLIpv6RulePort INTEGER
  swEgressACLIpv6RulePortGroup INTEGER
  swEgressACLIpv6RulePermit INTEGER
  swEgressACLIpv6RuleEnableReplacePriority INTEGER
  swEgressACLIpv6RuleReplacePriority INTEGER
  swEgressACLIpv6RuleEnableReplaceDscp INTEGER
  swEgressACLIpv6RuleReplaceDscp INTEGER
  swEgressAclIpv6RuleTimeRangeName DisplayString

SwEgressACLCounterEntry  
SEQUENCE    
  swEgressACLCounterProfileID INTEGER
  swEgressACLCounterAccessID INTEGER
  swEgressACLCounterState INTEGER
  swEgressACLCounterTotalCounter Counter64
  swEgressACLCounterGreenCounter Counter64
  swEgressACLCounterYellowCounter Counter64
  swEgressACLCounterRedCounter Counter64

SwEgressAclMeterEntry  
SEQUENCE    
  swEgressAclMeterProfileID INTEGER
  swEgressAclMeterAccessID INTEGER
  swEgressAclMeterRowStatus RowStatus
  swEgressAclMeterMode INTEGER
  swEgressAclMeterTrtcmCir INTEGER
  swEgressAclMeterTrtcmCbs INTEGER
  swEgressAclMeterTrtcmPir INTEGER
  swEgressAclMeterTrtcmPbs INTEGER
  swEgressAclMeterTrtcmColorMode INTEGER
  swEgressAclMeterTrtcmConformState INTEGER
  swEgressAclMeterTrtcmConformReplaceDscp INTEGER
  swEgressAclMeterTrtcmConformCounterState INTEGER
  swEgressAclMeterTrtcmExceedState INTEGER
  swEgressAclMeterTrtcmExceedReplaceDscp INTEGER
  swEgressAclMeterTrtcmExceedCounterState INTEGER
  swEgressAclMeterTrtcmViolateState INTEGER
  swEgressAclMeterTrtcmViolateReplaceDscp INTEGER
  swEgressAclMeterTrtcmViolateCounterState INTEGER
  swEgressAclMeterSrtcmCir INTEGER
  swEgressAclMeterSrtcmCbs INTEGER
  swEgressAclMeterSrtcmEbs INTEGER
  swEgressAclMeterSrtcmColorMode INTEGER
  swEgressAclMeterSrtcmConformState INTEGER
  swEgressAclMeterSrtcmConformReplaceDscp INTEGER
  swEgressAclMeterSrtcmConformCounterState INTEGER
  swEgressAclMeterSrtcmExceedState INTEGER
  swEgressAclMeterSrtcmExceedReplaceDscp INTEGER
  swEgressAclMeterSrtcmExceedCounterState INTEGER
  swEgressAclMeterSrtcmViolateState INTEGER
  swEgressAclMeterSrtcmViolateReplaceDscp INTEGER
  swEgressAclMeterSrtcmViolateCounterState INTEGER

SwEgressAclRateEntry  
SEQUENCE    
  swEgressAclRateProfileID INTEGER
  swEgressAclRateAccessID INTEGER
  swEgressAclRateRowStatus RowStatus
  swEgressAclRate INTEGER
  swEgressAclBurstSize INTEGER
  swEgressAclRateActionForRateExceed INTEGER
  swEgressAclRateRemarkDscp INTEGER

Defined Values

swEgressAclMgmtMIB 1.3.6.1.4.1.171.12.89
The structure of Egress Access Control List information for the proprietary enterprise.
MODULE-IDENTITY    

swEgressAclInfo 1.3.6.1.4.1.171.12.89.1
OBJECT IDENTIFIER    

swEgressAclMaskMgmt 1.3.6.1.4.1.171.12.89.2
OBJECT IDENTIFIER    

swEgressAclRuleMgmt 1.3.6.1.4.1.171.12.89.3
OBJECT IDENTIFIER    

swEgressAclMeteringMgmt 1.3.6.1.4.1.171.12.89.4
OBJECT IDENTIFIER    

swEgressACLTotalUsedRuleEntries 1.3.6.1.4.1.171.12.89.1.1
The total number of used egress ACL rule entries.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swEgressACLTotalUnusedRuleEntries 1.3.6.1.4.1.171.12.89.1.2
The total number of unused egress ACL rule entries.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swEgressACLEthernetTable 1.3.6.1.4.1.171.12.89.2.1
This table contains egress ACL mask Ethernet information. The access profile will be created on the switch to define which part of each outgoing frame's layer 2 header will be examined by the switch. Masks entered will be combined with the values the switch finds in the specified frame header fields.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwEgressACLEthernetEntry

swEgressACLEthernetEntry 1.3.6.1.4.1.171.12.89.2.1.1
A list of information about the egress ACL for Ethernet.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwEgressACLEthernetEntry  

swEgressACLEthernetProfileID 1.3.6.1.4.1.171.12.89.2.1.1.1
The ID of the egress ACL mask entry unique to the mask list. The maximum value of this object depends on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

swEgressACLEthernetRowStatus 1.3.6.1.4.1.171.12.89.2.1.1.2
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swEgressACLEthernetProfileName 1.3.6.1.4.1.171.12.89.2.1.1.3
The name of the egress ACL mask entry unique to the mask list.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..32)  

swEgressACLEthernetUsevlan 1.3.6.1.4.1.171.12.89.2.1.1.4
Specifies that the switch will examine the VLAN part of each packet header.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLEthernetVlanMask 1.3.6.1.4.1.171.12.89.2.1.1.5
The mask used for the VLAN ID. Valid values are from 0x0000 to 0x0FFF. The default value is 0x0FFF
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(2)  

swEgressACLEthernetUse8021p 1.3.6.1.4.1.171.12.89.2.1.1.6
Specifies if the switch will examine the 802.1p priority value in the frame's header or not.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLEthernetUseEthernetType 1.3.6.1.4.1.171.12.89.2.1.1.7
Specifies if the switch will examine the Ethernet type value in each frame's header or not.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLEthernetMacAddrMaskState 1.3.6.1.4.1.171.12.89.2.1.1.8
This object indicates the status of the MAC address mask. other (1) - Neither source MAC address nor destination MAC address is masked. dst-mac-addr (2) - Destination MAC addresses within received frames are to be filtered when matched with the MAC address entry for the table. src-mac-addr (3) - Source MAC addresses within received frames are to be filtered when matched with the MAC address entry for the table. dst-src-mac-addr (4) - Source or destination MAC addresses within received frames are to be filtered when matched with the MAC address entry of the table.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), dst-mac-addr(2), src-mac-addr(3), dst-src-mac-addr(4)  

swEgressACLEthernetSrcMacAddrMask 1.3.6.1.4.1.171.12.89.2.1.1.9
This object specifies the MAC address mask for the source MAC address.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

swEgressACLEthernetDstMacAddrMask 1.3.6.1.4.1.171.12.89.2.1.1.10
This object specifies the MAC address mask for the destination MAC address.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

swEgressACLEthernetUnusedRuleEntries 1.3.6.1.4.1.171.12.89.2.1.1.11
The number of unused rule entries of this Ethernet profile entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swEgressACLIpTable 1.3.6.1.4.1.171.12.89.2.2
This table contains the egress ACL mask for IP information. Access profiles will be created on the switch to define which part of the outgoing frame's IP layer packet header will be examined by the switch. Masks entered will be combined with the values the switch finds in the specified frame header fields.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwEgressACLIpEntry

swEgressACLIpEntry 1.3.6.1.4.1.171.12.89.2.2.1
A list of information about the egress ACL of the IP layer.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwEgressACLIpEntry  

swEgressACLIpProfileID 1.3.6.1.4.1.171.12.89.2.2.1.1
The ID of the egress ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

swEgressACLIpRowStatus 1.3.6.1.4.1.171.12.89.2.2.1.2
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swEgressACLIpProfileName 1.3.6.1.4.1.171.12.89.2.2.1.3
The name of the egress ACL mask entry unique to the mask list.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..32)  

swEgressACLIpUsevlan 1.3.6.1.4.1.171.12.89.2.2.1.4
This object indicates if the IP layer VLAN part is examined or not.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLIpVlanMask 1.3.6.1.4.1.171.12.89.2.2.1.5
The mask used for the VLAN ID. Valid values are from 0x0000 to 0x0FFF. The default value is 0x0FFF.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(2)  

swEgressACLIpIpAddrMaskState 1.3.6.1.4.1.171.12.89.2.2.1.6
This object indicates the status of IP address mask. other (1) - Neither source IP address nor destination IP address is masked. dst-ip-addr (2) - Destination IP addresses within received frames are to be filtered when matched with the IP address entry of the table. src-ip-addr (3) - Source IP addresses within received frames are to be filtered when matched with the IP address entry of the table. dst-src-ip-addr (4) - Destination or source IP addresses within received frames are to be filtered when matched with the IP address entry of the table.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), dst-ip-addr(2), src-ip-addr(3), dst-src-ip-addr(4)  

swEgressACLIpSrcIpAddrMask 1.3.6.1.4.1.171.12.89.2.2.1.7
This object specifies the IP address mask for the source IP address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

swEgressACLIpDstIpAddrMask 1.3.6.1.4.1.171.12.89.2.2.1.8
This object specifies the IP address mask for the destination IP address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

swEgressACLIpUseDSCP 1.3.6.1.4.1.171.12.89.2.2.1.9
This object indicates if the DSCP protocol in the packet header is to be examined or not.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLIpUseProtoType 1.3.6.1.4.1.171.12.89.2.2.1.10
That object indicates which protocol will be examined.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), icmp(2), igmp(3), tcp(4), udp(5), protocolId(6)  

swEgressACLIpIcmpOption 1.3.6.1.4.1.171.12.89.2.2.1.11
This object indicates which fields are defined for ICMP. none (1)- Both fields are null. type (2)- Type field identified. code (3)- Code field identified. type-code (4)- Both ICMP fields identified.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), type(2), code(3), type-code(4)  

swEgressACLIpIgmpOption 1.3.6.1.4.1.171.12.89.2.2.1.12
Indicates if the IGMP options field is identified or not.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLIpTcpOption 1.3.6.1.4.1.171.12.89.2.2.1.13
This object indicates the status of the filtered address of TCP. other (1) - Neither source port nor destination port is masked. dst-addr (2) - Packets will be filtered if this destination port is identified in received frames. src-addr (3) - Packets will be filtered if this source port is identified in received frames. dst-src-addr (4) - Packets will be filtered if this destination or source port is identified in received frames.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), dst-addr(2), src-addr(3), dst-src-addr(4)  

swEgressACLIpUdpOption 1.3.6.1.4.1.171.12.89.2.2.1.14
This object indicates the status of the filtered address of UDP . other (1) - Neither source port nor destination port is masked. dst-addr (2) - Packets will be filtered if this destination port is identified in received frames. src-addr (3) - Packets will be filtered if this source port is identified in received frames. dst-src-addr (4) - Packets will be filtered if this destination or source port is identified in received frames.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), dst-addr(2), src-addr(3), dst-src-addr(4)  

swEgressACLIpTCPorUDPSrcPortMask 1.3.6.1.4.1.171.12.89.2.2.1.15
Specifies a TCP port mask for the source port if swEgressACLIpUseProtoType is TCP Specifies a UDP port mask for the source port if swEgressACLIpUseProtoType is UDP.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(2)  

swEgressACLIpTCPorUDPDstPortMask 1.3.6.1.4.1.171.12.89.2.2.1.16
Specifies a TCP port mask for the destination port if swEgressACLIpUseProtoType is TCP Specifies a UDP port mask for the destination port if swEgressACLIpUseProtoType is UDP.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(2)  

swEgressACLIpTCPFlagBit 1.3.6.1.4.1.171.12.89.2.2.1.17
Specifies a TCP connection flag mask.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLIpTCPFlagBitMask 1.3.6.1.4.1.171.12.89.2.2.1.18
A value which indicates the set of TCP flags that this entity may potentially offer. The value is a sum of flag bits. This sum initially takes the value zero. Then, for each flag, L, is added in the range 1 through 6, for which this node performs transactions where 2^(L-1) is added to the sum. Note that values should be calculated accordingly: Flag functionality 6 urg bit 5 ack bit 4 psh bit 3 rst bit 2 syn bit 1 fin bit For example, if you want to enable urg bit and ack bit, you should set value 48{2^(5-1) + 2^(6-1)}.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..63  

swEgressACLIpProtoIDOption 1.3.6.1.4.1.171.12.89.2.2.1.19
Specifies if the switch will examine each frame's protocol ID field or not.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLIpProtoID 1.3.6.1.4.1.171.12.89.2.2.1.20
Specifies that the rule applies to the IP protocol ID behind the IP header.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..255  

swEgressACLIpProtoIDMask 1.3.6.1.4.1.171.12.89.2.2.1.21
Specifies that the rule applies to the IP protocol ID and the mask options behind the IP header.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(4)  

swEgressACLIpUnusedRuleEntries 1.3.6.1.4.1.171.12.89.2.2.1.22
The number of unused rule entries this IP profile entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swEgressACLIpv6MaskTable 1.3.6.1.4.1.171.12.89.2.3
This table contains IPv6 egress ACL mask information. An access profile will be created on the switch to define which parts of each outgoing frame's IPv6 part of the packet header will be examined by the switch. Masks entered will be combined with the values the switch finds in the specified frame header fields.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwEgressACLIpv6MaskEntry

swEgressACLIpv6MaskEntry 1.3.6.1.4.1.171.12.89.2.3.1
A list of information about egress ACL for IPv6.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwEgressACLIpv6MaskEntry  

swEgressACLIpv6MaskProfileID 1.3.6.1.4.1.171.12.89.2.3.1.1
The ID of the egress ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

swEgressACLIpv6MaskRowStatus 1.3.6.1.4.1.171.12.89.2.3.1.2
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swEgressACLIpv6MaskProfileName 1.3.6.1.4.1.171.12.89.2.3.1.3
The name of egress ACL mask entry unique to the mask list.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..32)  

swEgressACLIpv6MaskClass 1.3.6.1.4.1.171.12.89.2.3.1.4
This object indicates if the class field in the IPv6 packet header is to be examined or not.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLIpv6IpAddrMaskState 1.3.6.1.4.1.171.12.89.2.3.1.5
This object indicates the status of the IPv6 address mask. other (1) - Neither source IPv6 address nor destination IPv6 address is masked. dst-ipv6-addr (2) - Received frame destination IPv6 address is currently used to be filtered as it meets with the IPv6 address entry of the table. src-ipv6-addr (3) - Received frame source IPv6 address is currently used to be filtered as it meets with the IPv6 address entry of the table. dst-src-ipv6-addr (4) - Received frame destination IPv6 address or source IPv6 address is currently used to be filtered as it meets with the IPv6 address entry of the table.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), dst-ipv6-addr(2), src-ipv6-addr(3), dst-src-ipv6-addr(4)  

swEgressACLIpv6MaskSrcIpv6Mask 1.3.6.1.4.1.171.12.89.2.3.1.6
This object specifies the IPv6 address mask for the source IPv6 address.
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

swEgressACLIpv6MaskDstIpv6Mask 1.3.6.1.4.1.171.12.89.2.3.1.7
This object specifies the IPv6 address mask for the destination IPv6 address.
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

swEgressACLIpv6MaskUseProtoType 1.3.6.1.4.1.171.12.89.2.3.1.8
That object indicates which protocol will be examined.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), tcp(2), udp(3), icmp(4)  

swEgressACLIpv6MaskIcmpOption 1.3.6.1.4.1.171.12.89.2.3.1.9
This object indicates which fields are defined for ICMP. none (1)- Both fields are null. type (2)- Type field identified. code (3)- Code field identified. type-code (4)- Both ICMP fields identified.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), type(2), code(3), type-code(4)  

swEgressACLIpv6MaskTcpOption 1.3.6.1.4.1.171.12.89.2.3.1.10
This object indicates the status of the filtered address of TCP. other (1) - Neither source port nor destination port is masked. dst-addr (2) - Packets will be filtered if this destination port is identified in received frames. src-addr (3) - Packets will be filtered if this source port is identified in received frames. dst-src-addr (4) - Packets will be filtered if this destination or source port is identified in received frames.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), dst-addr(2), src-addr(3), dst-src-addr(4)  

swEgressACLIpv6MaskUdpOption 1.3.6.1.4.1.171.12.89.2.3.1.11
This object indicates the status of the filtered address of UDP. other (1) - Neither source port nor destination port is masked. dst-addr (2) - Packets will be filtered if this destination port is identified in received frames. src-addr (3) - Packets will be filtered if this source port is identified in received frames. dst-src-addr (4) - Packets will be filtered if this destination or source port is identified in received frames.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), dst-addr(2), src-addr(3), dst-src-addr(4)  

swEgressACLIpv6MaskTCPorUDPSrcPortMask 1.3.6.1.4.1.171.12.89.2.3.1.12
Specifies a TCP port mask for the source port if swEgressACLIpv6MaskUseProtoType is TCP Specifies a UDP port mask for the source port if swEgressACLIpv6MaskUseProtoType is UDP.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(2)  

swEgressACLIpv6MaskTCPorUDPDstPortMask 1.3.6.1.4.1.171.12.89.2.3.1.13
Specifies a TCP port mask for the destination port if swEgressACLIpv6MaskUseProtoType is TCP Specifies a UDP port mask for the destination port if swEgressACLIpv6MaskUseProtoType is UDP.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(2)  

swEgressACLIpv6MaskUnusedRuleEntries 1.3.6.1.4.1.171.12.89.2.3.1.14
The number of unused rule entries of this IPv6 profile entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swEgressACLMaskDelAllState 1.3.6.1.4.1.171.12.89.2.4
Used to delete all egress ACL masks.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), start(2)  

swEgressACLEtherRuleTable 1.3.6.1.4.1.171.12.89.3.1
This table contains Ethernet egress ACL information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwEgressACLEtherRuleEntry

swEgressACLEtherRuleEntry 1.3.6.1.4.1.171.12.89.3.1.1
A list of information about the egress ACL rule of the layer 2 part of each packet.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwEgressACLEtherRuleEntry  

swEgressACLEtherRuleProfileID 1.3.6.1.4.1.171.12.89.3.1.1.1
The ID of the egress ACL rule entry, which is unique to the mask list. The maximum value of this object depends on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

swEgressACLEtherRuleAccessID 1.3.6.1.4.1.171.12.89.3.1.1.2
The ID of the the egress ACL rule entry relates to the swEgressACLEtherRuleProfileID. When row creation is set to 0, this indicates the access ID will be assigned automatically. When set from 1 to 65535, an access ID will be created for the rule.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..65535  

swEgressACLEtherRuleRowStatus 1.3.6.1.4.1.171.12.89.3.1.1.3
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swEgressACLEtherRuleMatchVID 1.3.6.1.4.1.171.12.89.3.1.1.4
Specifies that the access rule will apply only to packets with this VLAN ID. It is applied to the specified ports configured by swEgressACLEtherRulePortGroup. Note:A value of 0 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  VlanIdOrNone  

swEgressACLEtherRuleMatchVlanMask 1.3.6.1.4.1.171.12.89.3.1.1.5
Specifies the per rule mask for the VLAN field as defined in swEgressACLEtherRuleVlan object. The value of this object when not in use is the corresponding mask in the profile mask. Once the value of this object is modified, the per rule mask will take effect.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(2)  

swEgressACLEtherRuleSrcMacAddress 1.3.6.1.4.1.171.12.89.3.1.1.6
Specifies that the access rule will apply to only packets with this source MAC address.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

swEgressACLEtherRuleMaskSrcMacAddress 1.3.6.1.4.1.171.12.89.3.1.1.7
Specifies the per rule mask for the source MAC addres field as defined in swEgressACLEtherRuleSrcMacAddress object. The value of this object when not in use is the corresponding mask in the profile mask. Once the value of this object is modified, the per rule mask will take effect.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

swEgressACLEtherRuleDstMacAddress 1.3.6.1.4.1.171.12.89.3.1.1.8
Specifies that the access rule will apply to packets with this destination MAC address.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

swEgressACLEtherRuleMaskDstMacAddress 1.3.6.1.4.1.171.12.89.3.1.1.9
Specifies the per rule mask for the destination MAC addres field as defined in swEgressACLEtherRuleDstMacAddress object. The value of this object when not in use is the corresponding mask in the profile mask. Once the value of this object is modified, the per rule mask will take effect.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

swEgressACLEtherRule8021P 1.3.6.1.4.1.171.12.89.3.1.1.10
Specifies that the access rule will apply to packets with this 802.1p priority value. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..7  

swEgressACLEtherRuleEtherType 1.3.6.1.4.1.171.12.89.3.1.1.11
Specifies that the access rule will apply to packets with this hexadecimal 802.1Q Ethernet type value in the packet header.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(2)  

swEgressACLEtherRuleVID 1.3.6.1.4.1.171.12.89.3.1.1.12
Specifies the VLAN-based ACL rule. There are two conditions: 1. this rule will apply to all the ports; 2. packets must belong to this VLAN. This object and swEgressACLEtherRulePortGroup,swEgressACLEtherRulePort cannot be set together. When you set swEgressACLEtherRulePortGroup or swEgressACLEtherRulePort, the value of this object will change to 0 automatically. This object cannot be set to 0.
Status: current Access: read-create
OBJECT-TYPE    
  VlanIdOrNone  

swEgressACLEtherRulePort 1.3.6.1.4.1.171.12.89.3.1.1.13
Specifies that the access rule will only apply to the port. This object and swEgressACLEtherRuleVID,swEgressACLEtherRulePortGroup can not be set together. When you set swEgressACLEtherRuleVID or swEgressACLEtherRulePortGroup, the value of this object will change to 0 automatically. This object can not be set to 0. A value of 0 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressACLEtherRulePortGroup 1.3.6.1.4.1.171.12.89.3.1.1.14
Specifies that the access rule will only apply to port(s) which belong to this port group. This object and swEgressACLEtherRuleVID, swEgressACLEtherRulePort can not be set together.When you set swEgressACLEtherRuleVID or swEgressACLEtherRulePort the value of this object will change to 0 automatically. Note:The range of this object is (0..N). The value N means the max number. It is determined by the project itself.A value of 0 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressACLEtherRulePermit 1.3.6.1.4.1.171.12.89.3.1.1.15
This object indicates if the result of the packet examination is 'permit' or 'deny'. The default is 'permit'. deny - Specifies that packets matching the access profile are not permitted to be forwarded by the switch and will be filtered. permit - Specifies that packets matching the access profile are permitted to be forwarded by the switch.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

swEgressACLEtherRuleEnableReplacePriority 1.3.6.1.4.1.171.12.89.3.1.1.16
Specifies if the switch will change priorities of packets that match the access profile 802.1p priority tag field or not .
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLEtherRuleReplacePriority 1.3.6.1.4.1.171.12.89.3.1.1.17
Specifies that the priority will be changed in packets while the swEgressACLEtherRuleEnablePriority is enabled.A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..7  

swEgressACLEtherRuleEnableReplaceDscp 1.3.6.1.4.1.171.12.89.3.1.1.18
Specifies if the switch will change priorities of packets that match the access profile DSCP field or not.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLEtherRuleReplaceDscp 1.3.6.1.4.1.171.12.89.3.1.1.19
Specifies a value to be written to the DSCP field of an outgoing packet that meets the criteria specified in the first part of the command. This value will over-write the value in the DSCP field of the packet. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..63  

swEgressAclEtherRuleTimeRangeName 1.3.6.1.4.1.171.12.89.3.1.1.20
Specifies a name of a time-range associated with a specific egress ACL entry. The time-range name must first be created before being associated with the access rule. If this name is an empty string, the time-range profile will no longer be associated with the access rule. When a rule is de-associated with a time range, the access rule will be enabled all the time.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

swEgressACLIpRuleTable 1.3.6.1.4.1.171.12.89.3.2
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwEgressACLIpRuleEntry

swEgressACLIpRuleEntry 1.3.6.1.4.1.171.12.89.3.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SwEgressACLIpRuleEntry  

swEgressACLIpRuleProfileID 1.3.6.1.4.1.171.12.89.3.2.1.1
The ID of the egress ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

swEgressACLIpRuleAccessID 1.3.6.1.4.1.171.12.89.3.2.1.2
The ID of the egress ACL rule entry relates to the swEgressACLEtherRuleProfileID. When row creation is set to 0, this indicates the access ID will be assigned automatically. When set from 1 to 65535, an access ID will be created for the rule.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..65535  

swEgressACLIpRuleRowStatus 1.3.6.1.4.1.171.12.89.3.2.1.3
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swEgressACLIpRuleMatchVID 1.3.6.1.4.1.171.12.89.3.2.1.4
Specifies that the access rule will apply only to packets with this VLAN ID. It is applied to the specified ports configured by swEgressACLIpRulePortGroup. Note:A value of 0 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  VlanIdOrNone  

swEgressACLIpMatchVlanMask 1.3.6.1.4.1.171.12.89.3.2.1.5
Specifies the per rule mask for the VLAN as defined in swEgressACLIpRuleVlan object. The value of this object when not in use is the corresponding mask in the profile mask. Once the value of this object is modified, the per rule mask will take effect. This object is writeable only once.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(2)  

swEgressACLIpRuleSrcIpaddress 1.3.6.1.4.1.171.12.89.3.2.1.6
Specifies an IP source address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

swEgressACLIpRuleMaskSrcIpaddress 1.3.6.1.4.1.171.12.89.3.2.1.7
Specifies the per rule mask for the source IP address as defined in swEgressACLIpRuleSrcIpaddress object. The value of this object when not in use is the corresponding mask in the profile mask. Once the value of this object is modified, the per rule mask will take effect. This object is writeable only once.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

swEgressACLIpRuleDstIpaddress 1.3.6.1.4.1.171.12.89.3.2.1.8
Specifies an IP destination address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

swEgressACLIpRuleMaskDstIpaddress 1.3.6.1.4.1.171.12.89.3.2.1.9
Specifies the per rule mask for the destination IP address as defined in swEgressACLIpRuleMaskDstIpaddress object. The value of this object when not in use is the corresponding mask in the profile mask. Once the value of this object is modified, the per rule mask will take effect. This object is writeable only once.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

swEgressACLIpRuleDscp 1.3.6.1.4.1.171.12.89.3.2.1.10
Specifies the value of DSCP. The value can be configured from 0 to 63. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..63  

swEgressACLIpRuleProtocol 1.3.6.1.4.1.171.12.89.3.2.1.11
Specifies the IP protocol.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), icmp(2), igmp(3), tcp(4), udp(5), protocolId(6)  

swEgressACLIpRuleType 1.3.6.1.4.1.171.12.89.3.2.1.12
Specifies that the rule applies to the value of ICMP/IGMP type traffic. A value of -1 denotes that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..255  

swEgressACLIpRuleCode 1.3.6.1.4.1.171.12.89.3.2.1.13
Specifies that the rule applies to the value of ICMP code traffic. A value of -1 denotes that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..255  

swEgressACLIpRuleSrcPort 1.3.6.1.4.1.171.12.89.3.2.1.14
Specifies that the rule applies to the range of the TCP/UDP source ports. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..65535  

swEgressACLIpRuleMaskSrcPort 1.3.6.1.4.1.171.12.89.3.2.1.15
Specifies the per rule mask for the L4 source port as defined in swEgressACLIpRuleSrcPort object. The value of this object when not in use is the corresponding mask in the profile mask. Once the value of this object is modified, the per rule mask will take effect. This object is writeable only once.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(2)  

swEgressACLIpRuleDstPort 1.3.6.1.4.1.171.12.89.3.2.1.16
Specifies the TCP/UDP destination port range. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..65535  

swEgressACLIpRuleMaskDstPort 1.3.6.1.4.1.171.12.89.3.2.1.17
Specifies the per rule mask for the L4 destination port as defined in swEgressACLIpRuleDstPort object. The value of this object when not in use is the corresponding mask in the profile mask. Once the value of this object is modified, the per rule mask will take effect. This object is writeable only once.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(2)  

swEgressACLIpRuleFlagBits 1.3.6.1.4.1.171.12.89.3.2.1.18
A value which indicates the set of TCP flags that this entity may potentially offer. The value is a sum of flag bits. This sum initially takes the value zero. Then, for each flag, L is added in the range 1 through 6, for which this node performs transactions, where 2^(L - 1) is added to the sum. Note that values should be calculated accordingly: Flag functionality 6 urg bit 5 ack bit 4 psh bit 3 rst bit 2 syn bit 1 fin bit For example, it you want to enable urg bit and ack bit, you should set value 48{2^(5-1) + 2^(6-1)}.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..63  

swEgressACLIpRuleProtoID 1.3.6.1.4.1.171.12.89.3.2.1.19
Specifies that the rule applies to the value of IP protocol ID traffic. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..255  

swEgressACLIpRuleUserDefine 1.3.6.1.4.1.171.12.89.3.2.1.20
Specifies that the rule applies to the first four byte behind the IP header.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(4)  

swEgressACLIpRuleUserDefineMask 1.3.6.1.4.1.171.12.89.3.2.1.21
Specifies the per rule mask for the first four byte behind the IP header as defined in swEgressACLIpRuleUserDefine object.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(4)  

swEgressACLIpRuleVID 1.3.6.1.4.1.171.12.89.3.2.1.22
Specifies the VLAN-based rule. There are two conditions: 1. this rule will apply to all the ports; 2. packets must belong to this VLAN. This object and swEgressACLIpRulePortGroup,swEgressACLIpRulePort cannot be set together. When you set swEgressACLIpRulePortGroup or swEgressACLIpRulePort , the value of this object will change to 0 automatically. This object cannot be set 0.
Status: current Access: read-create
OBJECT-TYPE    
  VlanIdOrNone  

swEgressACLIpRulePort 1.3.6.1.4.1.171.12.89.3.2.1.23
Specifies that the access rule will only apply to the port. This object and swEgressACLIpRuleVID,swEgressACLIpRulePortGroup can not be set together.When you set swEgressACLIpRuleVID or swEgressACLIpRulePortGroup, the value of this object will change to 0 automatically. This object can not be set to 0. A value of 0 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressACLIpRulePortGroup 1.3.6.1.4.1.171.12.89.3.2.1.24
Specifies that the access rule will only apply to port(s)which belong to this port group. This object and swEgressACLIpRuleVID,swEgressACLIpRulePort can not be set together. When you set swEgressACLIpRuleVID or swEgressACLIpRulePort , the value of this object will change to 0 automatically. Note:The range of this object is (0..N).The value N means the max number.It is determined by the project itself. A value of 0 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressACLIpRulePermit 1.3.6.1.4.1.171.12.89.3.2.1.25
This object indicates if the result of the packet examination is 'permit' or 'deny'. The default is 'permit'. deny - Specifies that packets matching the access profile are not permitted to be forwarded by the switch and will be filtered. permit - Specifies that packets matching the access profile are permitted to be forwarded by the switch.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

swEgressACLIpRuleEnableReplacePriority 1.3.6.1.4.1.171.12.89.3.2.1.26
Specifies whether the packets that match the access profile will change the 802.1p priority tag field by the switch or not.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLIpRuleReplacePriority 1.3.6.1.4.1.171.12.89.3.2.1.27
Specifies the priority will change in packets while the swEgressACLIpRuleEnablePriority is enabled.A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..7  

swEgressACLIpRuleEnableReplaceDscp 1.3.6.1.4.1.171.12.89.3.2.1.28
Specifies if the switch will change priorities of packets that match the access profile DSCP field or not.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLIpRuleReplaceDscp 1.3.6.1.4.1.171.12.89.3.2.1.29
Specifies a value to be written to the DSCP field of an outgoing packet that meets the criteria specified in the first part of the command. This value will over-write the value in the DSCP field of the packet. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..63  

swEgressAclIpRuleTimeRangeName 1.3.6.1.4.1.171.12.89.3.2.1.30
Specifies a name of a time-range associated with a specific egress ACL entry. The time-range name must first be created before being associated with the access rule. If this name is an empty string, the time-range profile will no longer be associated with the access rule. When a rule is de-associated with a time range, the access rule will be enabled all the time.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

swEgressACLIpv6RuleTable 1.3.6.1.4.1.171.12.89.3.3
This table contains the IPv6 egress ACL rule information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwEgressACLIpv6RuleEntry

swEgressACLIpv6RuleEntry 1.3.6.1.4.1.171.12.89.3.3.1
A list of information about egress ACL rules regarding the IPv6 part of each packet.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwEgressACLIpv6RuleEntry  

swEgressACLIpv6RuleProfileID 1.3.6.1.4.1.171.12.89.3.3.1.1
The ID of the egress ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

swEgressACLIpv6RuleAccessID 1.3.6.1.4.1.171.12.89.3.3.1.2
The ID of the the egress ACL rule entry relates to the swEgressACLEtherRuleProfileID. When row creation is set to 0, this indicates the access ID will be assigned automatically. When set from 1 to 65535, an access ID will be created for the rule.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..65535  

swEgressACLIpv6RuleRowStatus 1.3.6.1.4.1.171.12.89.3.3.1.3
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swEgressACLIpv6RuleClass 1.3.6.1.4.1.171.12.89.3.3.1.4
Specifies that the rule applies to the IPv6 class field. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..255  

swEgressACLIpv6RuleSrcIpv6Addr 1.3.6.1.4.1.171.12.89.3.3.1.5
Specifies that the rule applies to the source IPv6 address.
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

swEgressACLIpv6RuleMaskSrcIpv6Addr 1.3.6.1.4.1.171.12.89.3.3.1.6
Specifies that the per rule mask of swEgressACLIpv6RuleSrcIpv6Addr. The value of this object when not in use is the corresponding mask in the profile mask. Once the value of this object is modified, the per rule mask will take effect. This object is writeable only once.
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

swEgressACLIpv6RuleDstIpv6Addr 1.3.6.1.4.1.171.12.89.3.3.1.7
Specifies that the rule applies to the destination IPv6 address.
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

swEgressACLIpv6RuleMaskDstIpv6Addr 1.3.6.1.4.1.171.12.89.3.3.1.8
Specifies that the rule applies to the destination IPv6 address.
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

swEgressACLIpv6RuleProtocol 1.3.6.1.4.1.171.12.89.3.3.1.9
Specifies the IPv6 protocol.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), tcp(2), udp(3), icmp(4)  

swEgressACLIpv6RuleType 1.3.6.1.4.1.171.12.89.3.3.1.10
Specifies that the rule applies to the value of ICMP type traffic. A value of -1 denotes that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..255  

swEgressACLIpv6RuleCode 1.3.6.1.4.1.171.12.89.3.3.1.11
Specifies that the rule applies to the value of ICMP code traffic. A value of -1 denotes that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..255  

swEgressACLIpv6RuleSrcPort 1.3.6.1.4.1.171.12.89.3.3.1.12
Specifies that the rule applies to the range of the TCP/UDP source ports. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..65535  

swEgressACLIpv6RuleMaskSrcPort 1.3.6.1.4.1.171.12.89.3.3.1.13
Specifies that the per rule mask of swEgressACLIpv6RuleSrcPort. The value of this object when not in use is the corresponding mask in the profile mask. Once the value of this object is modified, the per rule mask will take effect. This object is writeable only once.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(2)  

swEgressACLIpv6RuleDstPort 1.3.6.1.4.1.171.12.89.3.3.1.14
Specifies the TCP/UDP destination port range. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..65535  

swEgressACLIpv6RuleMaskDstPort 1.3.6.1.4.1.171.12.89.3.3.1.15
Specifies the per rule mask of swEgressACLIpv6RuleDstPort. The value of this object when not in use is the corresponding mask in the profile mask. Once the value of this object is modified, the per rule mask will take effect. This object is writeable only once.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(2)  

swEgressACLIpv6RuleVID 1.3.6.1.4.1.171.12.89.3.3.1.16
Specifies this rule only applies to the specified VLAN. There are two conditions: 1.only the portlist that belongs to this VLAN will be included; 2.packets must belong to this VLAN. This object and swEgressACLIpv6RulePortGroup,swEgressACLIpv6RulePort cannot be set together. When you set swEgressACLIpv6RulePortGroup or swEgressACLIpv6RulePort, the value of this object will change to 0 automatically. The object cannot be set 0.
Status: current Access: read-create
OBJECT-TYPE    
  VlanIdOrNone  

swEgressACLIpv6RulePort 1.3.6.1.4.1.171.12.89.3.3.1.17
Specifies that the access rule will only apply to the port. This object and swEgressACLIpv6RuleVID,swEgressACLIpv6RulePortGroup can not be set together.When you set swEgressACLIpv6RuleVID or swEgressACLIpv6RulePortGroup, the value of this object will change to 0 automatically. This object can not be set to 0. A value of 0 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressACLIpv6RulePortGroup 1.3.6.1.4.1.171.12.89.3.3.1.18
Specifies that the access rule will apply only to port(s)which belong to this port group. This object and swEgressACLIpv6RuleVID,swEgressACLIpv6RulePort can not be set together. When you set swEgressACLIpv6RuleVID or swEgressACLIpv6RulePort, the value of this object will change to 0 automatically. Note:The range of this object is (0..N).The value N means the max number.It is determined by the project itself.A value of 0 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressACLIpv6RulePermit 1.3.6.1.4.1.171.12.89.3.3.1.19
This object indicates if the result of the packet examination is 'permit' or 'deny'. The default is 'permit'. deny - Specifies that packets matching the access profile are not permitted to be forwarded by the switch and will be filtered. permit - Specifies that packets matching the access profile are permitted to be forwarded by the switch.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

swEgressACLIpv6RuleEnableReplacePriority 1.3.6.1.4.1.171.12.89.3.3.1.20
Specifies if the switch will change priorities of packets that match the access profile 802.1p priority tag or not.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLIpv6RuleReplacePriority 1.3.6.1.4.1.171.12.89.3.3.1.21
Specifies the priority will change in packets while the swEgressACLIpv6RuleReplacePriority is enabled.A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..7  

swEgressACLIpv6RuleEnableReplaceDscp 1.3.6.1.4.1.171.12.89.3.3.1.22
Specifies if the switch will change priorities of packets that match the access profile DSCP field or not.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLIpv6RuleReplaceDscp 1.3.6.1.4.1.171.12.89.3.3.1.23
Specifies a value to be written to the DSCP field of an outgoing packet that meets the criteria specified in the first part of the command. This value will over-write the value in the DSCP field of the packet. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..63  

swEgressAclIpv6RuleTimeRangeName 1.3.6.1.4.1.171.12.89.3.3.1.24
Specifies a name of a time-range associated with a specific egress ACL entry. The time-range name must first be created before being associated with the access rule. If this name is an empty string, the time-range profile will no longer be associated with the access rule. When a rule is de-associated with a time range, the access rule will be enabled all the time.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

swEgressACLCounterTable 1.3.6.1.4.1.171.12.89.3.4
This table maintains counter information associated with a specific rule in the egress ACL rule table. Please refer to the swEgressACLEtherRuleTable, swEgressACLIpRuleTable, swEgressACLIpv6RuleTable for detailed ACL rule information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwEgressACLCounterEntry

swEgressACLCounterEntry 1.3.6.1.4.1.171.12.89.3.4.1
The entry maintains counter information associated with the egress ACL rule table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwEgressACLCounterEntry  

swEgressACLCounterProfileID 1.3.6.1.4.1.171.12.89.3.4.1.1
The ID of the egress ACL mask entry, which is unique in the mask list.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

swEgressACLCounterAccessID 1.3.6.1.4.1.171.12.89.3.4.1.2
The ID of the egress ACL rule entry as related to the swEgressACLCounterProfileID.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..65535  

swEgressACLCounterState 1.3.6.1.4.1.171.12.89.3.4.1.3
Specifies whether the counter feature will be enabled or disabled. 1. This is optional. The default is 'disabled'. 2. If the rule is not bound with flow-meter, then all packets that match will be counted. If the rule is bound with flow-meter, then the 'counter' will be overridden.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressACLCounterTotalCounter 1.3.6.1.4.1.171.12.89.3.4.1.4
The number of matched packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

swEgressACLCounterGreenCounter 1.3.6.1.4.1.171.12.89.3.4.1.5
The number of matched green packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

swEgressACLCounterYellowCounter 1.3.6.1.4.1.171.12.89.3.4.1.6
The number of matched yellow packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

swEgressACLCounterRedCounter 1.3.6.1.4.1.171.12.89.3.4.1.7
The number of matched red packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

swEgressAclMeterTable 1.3.6.1.4.1.171.12.89.4.1
This table is used to configure the flow-based metering function. The access rule must first be created before the parameters of this function can be applied. Users may set the preferred bandwidth for this rule, in Kbps; once the bandwidth has been exceeded, overflow packets will be either dropped or set for a drop precedence, depending on user configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwEgressAclMeterEntry

swEgressAclMeterEntry 1.3.6.1.4.1.171.12.89.4.1.1
This entry displays parameters and configurations set for the flow metering function.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwEgressAclMeterEntry  

swEgressAclMeterProfileID 1.3.6.1.4.1.171.12.89.4.1.1.1
The ID of the ACL mask entry is unique in the mask list. The maximum value of this object depends on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

swEgressAclMeterAccessID 1.3.6.1.4.1.171.12.89.4.1.1.2
The ID of the egress ACL rule entry as related to the swEgressAclMeterProfileID.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..65535  

swEgressAclMeterRowStatus 1.3.6.1.4.1.171.12.89.4.1.1.3
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swEgressAclMeterMode 1.3.6.1.4.1.171.12.89.4.1.1.4
tr-tcm: two rate three color mode; sr-tcm: single rate three color mode;
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), tr-tcm(2), sr-tcm(3)  

swEgressAclMeterTrtcmCir 1.3.6.1.4.1.171.12.89.4.1.1.5
Specifies the 'committed information rate' of 'two rate three color mode'. The unit is Kbps.A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressAclMeterTrtcmCbs 1.3.6.1.4.1.171.12.89.4.1.1.6
Specifies the 'committed burst size' of 'two rate three color mode'. 1. The unit is Kbytes. That is to say, 1 means 1Kbytes. 2. This parameter is an optional parameter. The default value is 4kbytes. Note:The set value range is 0..N. The value N is determined by project. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressAclMeterTrtcmPir 1.3.6.1.4.1.171.12.89.4.1.1.7
Specifies the 'Peak Information Rate' of 'two rate three color mode'. The unit is Kbps.A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressAclMeterTrtcmPbs 1.3.6.1.4.1.171.12.89.4.1.1.8
Specifies the 'peak burst size' of 'two rate three color mode'. 1. The unit is Kbytes. That is to say, 1 means 1kbytes. 2. This parameter is an optional parameter. The default value is 4kbytes. Note:The set value range is 0..N.The value N is determined by project. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressAclMeterTrtcmColorMode 1.3.6.1.4.1.171.12.89.4.1.1.9
Specifies the meter mode. The default is color-blind mode. The final color of the packet is determined by the initial color of the packet and the metering result.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER color-blind(1), color-aware(2)  

swEgressAclMeterTrtcmConformState 1.3.6.1.4.1.171.12.89.4.1.1.10
Specifies the action state when packet is in 'green color'. permit: permit the packet. replace-dscp: change the DSCP value of packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), permit(2), replace-dscp(3)  

swEgressAclMeterTrtcmConformReplaceDscp 1.3.6.1.4.1.171.12.89.4.1.1.11
Specifies the DSCP value of the packet when the packet is in 'green color'. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..63  

swEgressAclMeterTrtcmConformCounterState 1.3.6.1.4.1.171.12.89.4.1.1.12
Specifies the counter state when the packet is in 'green color'. 1. This is optional. The default is 'disabled'. 2. The resource may be limited so that the counter cannot be turned on. The limitation is project dependent. 3. counter will be cleared when the function is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressAclMeterTrtcmExceedState 1.3.6.1.4.1.171.12.89.4.1.1.13
Specifies the action state when packet is in 'yellow color'. permit: permit the packet. replace-dscp: change the DSCP value of the packet. drop: drop the packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), permit(2), replace-dscp(3), drop(4)  

swEgressAclMeterTrtcmExceedReplaceDscp 1.3.6.1.4.1.171.12.89.4.1.1.14
Specifies the DSCP value of packet when packet is in 'yellow color'. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..63  

swEgressAclMeterTrtcmExceedCounterState 1.3.6.1.4.1.171.12.89.4.1.1.15
Specifies the counter state when packet is in 'yellow color'. 1. This is optional. The default is 'disabled'. 2. The resource may be limited so that the counter cannot be turned on. The limitation is project dependent. 3. counter will be cleared when the function is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressAclMeterTrtcmViolateState 1.3.6.1.4.1.171.12.89.4.1.1.16
Specifies the action state when packet is in 'red color'. permit: permit the packet. replace-dscp: change the DSCP value of packet. drop: drop the packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), permit(2), replace-dscp(3), drop(4)  

swEgressAclMeterTrtcmViolateReplaceDscp 1.3.6.1.4.1.171.12.89.4.1.1.17
Specifies the DSCP value of the packet when packet is in 'red color'. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..63  

swEgressAclMeterTrtcmViolateCounterState 1.3.6.1.4.1.171.12.89.4.1.1.18
Specifies the counter state when packet is in 'red color'. 1. This is optional. The default is 'disabled'. 2. The resource may be limited so that the counter cannot be turned on. The limitation is project dependent. 3. counter will be cleared when the function is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressAclMeterSrtcmCir 1.3.6.1.4.1.171.12.89.4.1.1.19
Specifies the 'committed information rate' of 'single rate three color mode'. The unit is Kbps. A value of -1 indicates that this object is not active
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressAclMeterSrtcmCbs 1.3.6.1.4.1.171.12.89.4.1.1.20
Specifies the 'committed burst size' of 'single rate three color mode'. The unit is Kbytes. That is to say, 1 means 1Kbytes. The set value range is 0..N.The value N is determined by project. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressAclMeterSrtcmEbs 1.3.6.1.4.1.171.12.89.4.1.1.21
Specifies the 'Excess burst size' of 'single rate three color mode'. The unit is Kbytes. That is to say, 1 means 1kbytes. The set value range is 0..N.The value N is determined by project. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressAclMeterSrtcmColorMode 1.3.6.1.4.1.171.12.89.4.1.1.22
Specifies the meter mode. The default is color-blind mode. The final color of packet is determined by the initial color of the packet and the metering result.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER color-blind(1), color-aware(2)  

swEgressAclMeterSrtcmConformState 1.3.6.1.4.1.171.12.89.4.1.1.23
Specifies the action state when the packet is in 'green color'. permit: permit the packet. replace-dscp: change the DSCP value of packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), permit(2), replace-dscp(3)  

swEgressAclMeterSrtcmConformReplaceDscp 1.3.6.1.4.1.171.12.89.4.1.1.24
Specifies the DSCP value of the packet when packet is in 'green color'. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..63  

swEgressAclMeterSrtcmConformCounterState 1.3.6.1.4.1.171.12.89.4.1.1.25
Specifies the counter state when the packet is in 'green color'. 1. This is optional. The default is 'disabled'. 2. The resource may be limited such that counter cannot be turned on. The limitation is project dependent. 3. counter will be cleared when the function is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressAclMeterSrtcmExceedState 1.3.6.1.4.1.171.12.89.4.1.1.26
Specifies the action state when the packet is in 'yellow color'. permit: permit the packet. replace-dscp: change the DSCP value of packet. drop: drop the packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), permit(2), replace-dscp(3), drop(4)  

swEgressAclMeterSrtcmExceedReplaceDscp 1.3.6.1.4.1.171.12.89.4.1.1.27
Specifies the DSCP value of the packet when packet is in 'yellow color'. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..63  

swEgressAclMeterSrtcmExceedCounterState 1.3.6.1.4.1.171.12.89.4.1.1.28
Specifies the counter state when the packet is in 'yellow color'. 1. This is optional. The default is 'disabled'. 2. The resource may be limited such that counter cannot be turned on. The limitation is project dependent. 3. counter will be cleared when the function is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressAclMeterSrtcmViolateState 1.3.6.1.4.1.171.12.89.4.1.1.29
Specifies the action state when the packet is in 'red color'. permit: permit the packet. replace-dscp: change the DSCP value of packet. drop: drop the packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), permit(2), replace-dscp(3), drop(4)  

swEgressAclMeterSrtcmViolateReplaceDscp 1.3.6.1.4.1.171.12.89.4.1.1.30
Specifies the DSCP value of the packet when packet is in 'red color'. A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..63  

swEgressAclMeterSrtcmViolateCounterState 1.3.6.1.4.1.171.12.89.4.1.1.31
Specifies the counter state when the packet is in 'red color'. 1. This is optional. The default is 'diabled'. 2. The resource may be limited so that the counter cannot be turned on. The limitation is project dependent. 3. counter will be cleared when the function is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swEgressAclRateTable 1.3.6.1.4.1.171.12.89.4.2
This table is used to configure the single rate two color metering function. The egress access rule must first be created before the parameters of this function can be applied. Users may set the preferred bandwidth for this rule, in Kbps; once the bandwidth has been exceeded, overflow packets will be either dropped or set for a drop precedence, depending on user configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwEgressAclRateEntry

swEgressAclRateEntry 1.3.6.1.4.1.171.12.89.4.2.1
This entry displays parameters and configurations set for the single rate two color function.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwEgressAclRateEntry  

swEgressAclRateProfileID 1.3.6.1.4.1.171.12.89.4.2.1.1
The ID of the egress ACL mask entry is unique in the mask list. The maximum value of this object depends on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

swEgressAclRateAccessID 1.3.6.1.4.1.171.12.89.4.2.1.2
The ID of the egress ACL rule entry as related to the swEgressAclRateProfileID.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..65535  

swEgressAclRateRowStatus 1.3.6.1.4.1.171.12.89.4.2.1.3
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swEgressAclRate 1.3.6.1.4.1.171.12.89.4.2.1.4
Specifies the committed bandwidth in Kbps for the flow. A value of -1 indicates that this object is not active. NOTE: Users must set the swEgressAclRateActionForRateExceed object to activate this entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressAclBurstSize 1.3.6.1.4.1.171.12.89.4.2.1.5
This specifies the burst size for the single rate two color mode. The unit is Kbytes. That is to say, 1 means 1kbytes. The set value range is 0..N, the value N is determined by project. A value of -1 indicates that this object is not active. This parameter is an optional parameter. The default value is 4kbytes.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swEgressAclRateActionForRateExceed 1.3.6.1.4.1.171.12.89.4.2.1.6
Specifies the action to take for those packets exceeding the committed rate. drop-packet: drop the packet. replace-dscp: change the DSCP value of the packet. NOTE: Users must set the swEgressAclRate to activate this entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), drop-packet(2), remark-dscp(3)  

swEgressAclRateRemarkDscp 1.3.6.1.4.1.171.12.89.4.2.1.7
Mark the packet with a specified DSCP. It can be set when swEgressAclRateActionForRateExceed sets remark-dscp(3). A value of -1 indicates that this object is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..63  

swEgressAclMeteringNumOfEntryInUse 1.3.6.1.4.1.171.12.89.4.3
Used to display total entries of the flow metering.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor