EATON-EPDU-MIB

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
EATON-OIDS

Imported symbols

OBJECT-TYPE	NOTIFICATION-TYPE	MODULE-IDENTITY
Counter32	Unsigned32	Integer32
NOTIFICATION-GROUP	OBJECT-GROUP	MODULE-COMPLIANCE
TEXTUAL-CONVENTION	DateAndTime	DisplayString
pduAgent

Defined Types

UnixTimeStamp
Unix time stamp. Measured in seconds since January 1, 1970.
TEXTUAL-CONVENTION
	Counter32

UnitEntry
SEQUENCE
	strappingIndex	Integer32
	productName	OCTET STRING
	partNumber	OCTET STRING
	serialNumber	OCTET STRING
	firmwareVersion	OCTET STRING
	unitName	OCTET STRING
	lcdControl	INTEGER
	clockValue	DateAndTime
	temperatureScale	INTEGER
	unitType	INTEGER
	inputCount	Integer32
	groupCount	Integer32
	outletCount	Integer32
	temperatureCount	Integer32
	humidityCount	Integer32
	contactCount	Integer32
	communicationStatus	INTEGER
	internalStatus	INTEGER
	strappingStatus	INTEGER
	userName	OCTET STRING
	commInterface	INTEGER

UnitControlEntry
SEQUENCE
	unitControlOffCmd	Integer32
	unitControlOnCmd	Integer32

InputEntry
SEQUENCE
	inputIndex	Integer32
	inputType	INTEGER
	inputFrequency	Integer32
	inputFrequencyStatus	INTEGER
	inputVoltageCount	Integer32
	inputCurrentCount	Integer32
	inputPowerCount	Integer32
	inputPlugType	INTEGER

InputVoltageEntry
SEQUENCE
	inputVoltageIndex	Integer32
	inputVoltageMeasType	INTEGER
	inputVoltage	Integer32
	inputVoltageThStatus	INTEGER
	inputVoltageThLowerWarning	Integer32
	inputVoltageThLowerCritical	Integer32
	inputVoltageThUpperWarning	Integer32
	inputVoltageThUpperCritical	Integer32

InputCurrentEntry
SEQUENCE
	inputCurrentIndex	Integer32
	inputCurrentMeasType	INTEGER
	inputCurrentCapacity	Integer32
	inputCurrent	Integer32
	inputCurrentThStatus	INTEGER
	inputCurrentThLowerWarning	Integer32
	inputCurrentThLowerCritical	Integer32
	inputCurrentThUpperWarning	Integer32
	inputCurrentThUpperCritical	Integer32
	inputCurrentCrestFactor	Integer32
	inputCurrentPercentLoad	Integer32

InputPowerEntry
SEQUENCE
	inputPowerIndex	Integer32
	inputPowerMeasType	INTEGER
	inputVA	Integer32
	inputWatts	Integer32
	inputWh	Unsigned32
	inputWhTimer	UnixTimeStamp
	inputPowerFactor	Integer32
	inputVAR	Integer32

InputTotalPowerEntry
SEQUENCE
	inputTotalVA	Integer32
	inputTotalWatts	Integer32
	inputTotalWh	Unsigned32
	inputTotalWhTimer	UnixTimeStamp
	inputTotalPowerFactor	Integer32
	inputTotalVAR	Integer32

GroupEntry
SEQUENCE
	groupIndex	Integer32
	groupID	DisplayString
	groupName	OCTET STRING
	groupType	INTEGER
	groupBreakerStatus	INTEGER
	groupChildCount	Integer32

GroupChildEntry
SEQUENCE
	groupChildIndex	Integer32
	groupChildType	INTEGER
	groupChildOID	OBJECT IDENTIFIER

GroupVoltageEntry
SEQUENCE
	groupVoltageMeasType	INTEGER
	groupVoltage	Integer32
	groupVoltageThStatus	INTEGER
	groupVoltageThLowerWarning	Integer32
	groupVoltageThLowerCritical	Integer32
	groupVoltageThUpperWarning	Integer32
	groupVoltageThUpperCritical	Integer32

GroupCurrentEntry
SEQUENCE
	groupCurrentCapacity	Integer32
	groupCurrent	Integer32
	groupCurrentThStatus	INTEGER
	groupCurrentThLowerWarning	Integer32
	groupCurrentThLowerCritical	Integer32
	groupCurrentThUpperWarning	Integer32
	groupCurrentThUpperCritical	Integer32
	groupCurrentCrestFactor	Integer32
	groupCurrentPercentLoad	Integer32

GroupPowerEntry
SEQUENCE
	groupVA	Integer32
	groupWatts	Integer32
	groupWh	Unsigned32
	groupWhTimer	UnixTimeStamp
	groupPowerFactor	Integer32
	groupVAR	Integer32

GroupControlEntry
SEQUENCE
	groupControlStatus	INTEGER
	groupControlOffCmd	Integer32
	groupControl0nCmd	Integer32
	groupControlRebootCmd	Integer32

OutletEntry
SEQUENCE
	outletIndex	Integer32
	outletID	DisplayString
	outletName	OCTET STRING
	outletParentCount	Integer32
	outletType	INTEGER

OutletParentEntry
SEQUENCE
	outletParentIndex	Integer32
	outletParentType	INTEGER
	outletParentOID	OBJECT IDENTIFIER

OutletVoltageEntry
SEQUENCE
	outletVoltage	Integer32
	outletVoltageThStatus	INTEGER
	outletVoltageThLowerWarning	Integer32
	outletVoltageThLowerCritical	Integer32
	outletVoltageThUpperWarning	Integer32
	outletVoltageThUpperCritical	Integer32

OutletCurrentEntry
SEQUENCE
	outletCurrentCapacity	Integer32
	outletCurrent	Integer32
	outletCurrentThStatus	INTEGER
	outletCurrentThLowerWarning	Integer32
	outletCurrentThLowerCritical	Integer32
	outletCurrentThUpperWarning	Integer32
	outletCurrentThUpperCritical	Integer32
	outletCurrentCrestFactor	Integer32
	outletCurrentPercentLoad	Integer32

OutletPowerEntry
SEQUENCE
	outletVA	Integer32
	outletWatts	Integer32
	outletWh	Unsigned32
	outletWhTimer	UnixTimeStamp
	outletPowerFactor	Integer32
	outletVAR	Integer32

OutletControlEntry
SEQUENCE
	outletControlStatus	INTEGER
	outletControlOffCmd	Integer32
	outletControlOnCmd	Integer32
	outletControlRebootCmd	Integer32
	outletControlPowerOnState	INTEGER
	outletControlSequenceDelay	Integer32
	outletControlRebootOffTime	Integer32
	outletControlSwitchable	INTEGER
	outletControlShutoffDelay	Integer32

TemperatureEntry
SEQUENCE
	temperatureIndex	Integer32
	temperatureName	OCTET STRING
	temperatureProbeStatus	INTEGER
	temperatureValue	Integer32
	temperatureThStatus	INTEGER
	temperatureThLowerWarning	Integer32
	temperatureThLowerCritical	Integer32
	temperatureThUpperWarning	Integer32
	temperatureThUpperCritical	Integer32

HumidityEntry
SEQUENCE
	humidityIndex	Integer32
	humidityName	OCTET STRING
	humidityProbeStatus	INTEGER
	humidityValue	Integer32
	humidityThStatus	INTEGER
	humidityThLowerWarning	Integer32
	humidityThLowerCritical	Integer32
	humidityThUpperWarning	Integer32
	humidityThUpperCritical	Integer32

ContactEntry
SEQUENCE
	contactIndex	Integer32
	contactName	OCTET STRING
	contactProbeStatus	INTEGER
	contactState	INTEGER

Defined Values

eatonEpdu		1.3.6.1.4.1.534.6.6.7
The MIB module for Eaton ePDUs (Enclosure Power Distribution Units).
MODULE-IDENTITY

notifications		1.3.6.1.4.1.534.6.6.7.0
OBJECT IDENTIFIER

units		1.3.6.1.4.1.534.6.6.7.1
OBJECT IDENTIFIER

inputs		1.3.6.1.4.1.534.6.6.7.3
OBJECT IDENTIFIER

groups		1.3.6.1.4.1.534.6.6.7.5
OBJECT IDENTIFIER

outlets		1.3.6.1.4.1.534.6.6.7.6
OBJECT IDENTIFIER

environmental		1.3.6.1.4.1.534.6.6.7.7
OBJECT IDENTIFIER

conformance		1.3.6.1.4.1.534.6.6.7.25
OBJECT IDENTIFIER

objectGroups		1.3.6.1.4.1.534.6.6.7.25.5
OBJECT IDENTIFIER

notifyUserLogin		1.3.6.1.4.1.534.6.6.7.0.1
Sent whenever a user logs in.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyUserLogout		1.3.6.1.4.1.534.6.6.7.0.2
Sent whenever a user logs out.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyFailedLogin		1.3.6.1.4.1.534.6.6.7.0.3
Sent when someone attempts to log in and fails. On some models, may be sent after three failed login attempts.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyBootUp		1.3.6.1.4.1.534.6.6.7.0.4
Sent whenever an ePDU finishes booting up (hard or soft reboot).
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyInputVoltageThStatus		1.3.6.1.4.1.534.6.6.7.0.11
Sent whenever an input voltage threshold status changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyInputCurrentThStatus		1.3.6.1.4.1.534.6.6.7.0.12
Sent whenever an input current threshold status changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyInputFrequencyStatus		1.3.6.1.4.1.534.6.6.7.0.13
Sent whenever the input frequency status changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyGroupVoltageThStatus		1.3.6.1.4.1.534.6.6.7.0.21
Sent whenever a group voltage threshold status changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyGroupCurrentThStatus		1.3.6.1.4.1.534.6.6.7.0.22
Sent whenever a group current threshold status changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyGroupBreakerStatus		1.3.6.1.4.1.534.6.6.7.0.23
Sent whenever a group status changes to indicate whether the circuit breaker is on or off.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyOutletVoltageThStatus		1.3.6.1.4.1.534.6.6.7.0.31
Sent whenever an outlet voltage threshold status changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyOutletCurrentThStatus		1.3.6.1.4.1.534.6.6.7.0.32
Sent whenever an outlet current threshold status changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyOutletControlStatus		1.3.6.1.4.1.534.6.6.7.0.33
Sent whenever an outlet state On / Off changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyTemperatureThStatus		1.3.6.1.4.1.534.6.6.7.0.41
Sent whenever a temperature threshold status changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyHumidityThStatus		1.3.6.1.4.1.534.6.6.7.0.42
Sent whenever a humidity threshold status changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyContactState		1.3.6.1.4.1.534.6.6.7.0.43
Sent whenever a contact sensor state changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyProbeStatus		1.3.6.1.4.1.534.6.6.7.0.44
Sent whenever the environment probe status changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyCommunicationStatus		1.3.6.1.4.1.534.6.6.7.0.51
Sent whenever the PDU communication status changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyInternalStatus		1.3.6.1.4.1.534.6.6.7.0.52
Sent whenever the PDU internal status changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyTest		1.3.6.1.4.1.534.6.6.7.0.53
Sent whenever the trap test feature is used by the communication card.
Status: current	Access: read-write
NOTIFICATION-TYPE

notifyStrappingStatus		1.3.6.1.4.1.534.6.6.7.0.54
Sent whenever the strapping communication status changes.
Status: current	Access: read-write
NOTIFICATION-TYPE

unitsPresent		1.3.6.1.4.1.534.6.6.7.1.1
Each unit is identified by a Strapping Index. This object returns a comma-delimited list of the Strapping Indexes of all units present in the strapping group. For example, if units 0, 1, 5, and 7 are present, this value will be '0,1,5,7'. For units that do not support strapping, a Strapping Index of '0' is assumed.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

unitTable		1.3.6.1.4.1.534.6.6.7.1.2
A list of units. In most cases this list will only contain one entry. However, some units have a 'strapping' feature which allow units to be daisy-chained together such that all of them can be accessed through the SNMP interface of the master. If strapping is enabled, the strapping indexes of the units that can be accessed will be listed in the unitsPresent object.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UnitEntry

unitEntry		1.3.6.1.4.1.534.6.6.7.1.2.1
An entry for a PDU.
Status: current	Access: not-accessible
OBJECT-TYPE
	UnitEntry

strappingIndex		1.3.6.1.4.1.534.6.6.7.1.2.1.1
For units that support 'strapping' functionality, this will be a unique value for each unit. If units do not support 'strapping', this will always be '0'.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32	0..23

productName		1.3.6.1.4.1.534.6.6.7.1.2.1.2
Name of the product.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1..127)

partNumber		1.3.6.1.4.1.534.6.6.7.1.2.1.3
Part number of the unit.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

serialNumber		1.3.6.1.4.1.534.6.6.7.1.2.1.4
Serial number of the unit.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

firmwareVersion		1.3.6.1.4.1.534.6.6.7.1.2.1.5
Firmware version.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

unitName		1.3.6.1.4.1.534.6.6.7.1.2.1.6
Descriptive name for the unit.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..63)

lcdControl		1.3.6.1.4.1.534.6.6.7.1.2.1.7
Control the local LCD.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(0), lcdScreenOff(1), lcdKeyLock(2), lcdScreenOffAndKeyLock(3)

clockValue		1.3.6.1.4.1.534.6.6.7.1.2.1.8
Clock value. This could be from either a real-time clock (in which case it is likely writeable) or from a time server via NTP (probably read-only).
Status: current	Access: read-write
OBJECT-TYPE
	DateAndTime

temperatureScale		1.3.6.1.4.1.534.6.6.7.1.2.1.9
Scale used to return temperature objects.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	celsius(0), fahrenheit(1)

unitType		1.3.6.1.4.1.534.6.6.7.1.2.1.10
Technical capabilities of the PDU. Functionality is as follows: Monitored (MI) - input and usually section/group monitoring. Advanced Monitored (AM) - input, section/group, and outlet monitoring. Switched (SW) - input and section/group monitoring, outlet switching. Managed (MA) - input, section/group, and outlet monitoring plug outlet switching.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), switched(1), advancedMonitored(2), managed(3), monitored(4)

inputCount		1.3.6.1.4.1.534.6.6.7.1.2.1.20
Number of inputs on this ePDU.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

groupCount		1.3.6.1.4.1.534.6.6.7.1.2.1.21
Number of groups on this ePDU. Groups include breakers, outlet sections, and user-defined groups.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

outletCount		1.3.6.1.4.1.534.6.6.7.1.2.1.22
Number of outlets on this ePDU.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

temperatureCount		1.3.6.1.4.1.534.6.6.7.1.2.1.23
Max number of temperature measurements on this ePDU.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

humidityCount		1.3.6.1.4.1.534.6.6.7.1.2.1.24
Max number of humidity measurements on this ePDU.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

contactCount		1.3.6.1.4.1.534.6.6.7.1.2.1.25
Max number of contact sensors on this ePDU.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

communicationStatus		1.3.6.1.4.1.534.6.6.7.1.2.1.30
Status of the internal communication with the PDU.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	good(0), communicationLost(1)

internalStatus		1.3.6.1.4.1.534.6.6.7.1.2.1.31
Status of the internal failure inside the PDU.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	good(0), internalFailure(1)

strappingStatus		1.3.6.1.4.1.534.6.6.7.1.2.1.32
Status of the external communication with a strapping unit.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	good(0), communicationLost(1)

userName		1.3.6.1.4.1.534.6.6.7.1.2.1.40
Username used to log into the PDU.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	OCTET STRING	Size(0..31)

commInterface		1.3.6.1.4.1.534.6.6.7.1.2.1.41
Communications interface used to log into the PDU.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	serial(0), usb(1), telnet(2), web(3), ftp(4), xml(5)

unitControlTable		1.3.6.1.4.1.534.6.6.7.1.3
A list of units that have controllable outlets.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UnitControlEntry

unitControlEntry		1.3.6.1.4.1.534.6.6.7.1.3.1
An entry for a PDU which has controllable outlets.
Status: current	Access: not-accessible
OBJECT-TYPE
	UnitControlEntry

unitControlOffCmd		1.3.6.1.4.1.534.6.6.7.1.3.1.2
Unit-level outlet control command. Once the command is issued, outlets will turn Off. 0-n : Time in seconds until the outlet Sequence Off command is issued -1 : Cancel a pending unit-level Off command When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control commands. These will respond with an error if a command value of > 0 is written to this object.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..99999

unitControlOnCmd		1.3.6.1.4.1.534.6.6.7.1.3.1.3
Unit-level outlet control command. Once the command is issued, outlets will turn On according to their outletControlSequenceDelay value. 0-n : Time in seconds until the outlet Sequence On command is issued -1 : Cancel a pending unit-level On command When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control commands. These will respond with an error if a command value of > 0 is written to this object.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..99999

inputTable		1.3.6.1.4.1.534.6.6.7.3.1
List of inputs to the PDU.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		InputEntry

inputEntry		1.3.6.1.4.1.534.6.6.7.3.1.1
An entry for a particular input.
Status: current	Access: not-accessible
OBJECT-TYPE
	InputEntry

inputIndex		1.3.6.1.4.1.534.6.6.7.3.1.1.1
A unique value for each input. Its value ranges from 1 to inputCount.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32	1..2

inputType		1.3.6.1.4.1.534.6.6.7.3.1.1.2
Type of input - single phase, split phase, three phase delta, or three phase wye.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	singlePhase(1), splitPhase(2), threePhaseDelta(3), threePhaseWye(4)

inputFrequency		1.3.6.1.4.1.534.6.6.7.3.1.1.3
Units are 0.1 Hz; divide by ten to get Hz.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputFrequencyStatus		1.3.6.1.4.1.534.6.6.7.3.1.1.4
Status of the measured input frequency relative to the nominal frequency and the admitted tolerance.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	good(0), outOfRange(1)

inputVoltageCount		1.3.6.1.4.1.534.6.6.7.3.1.1.5
Number of input voltage measurements on this ePDU.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputCurrentCount		1.3.6.1.4.1.534.6.6.7.3.1.1.6
Number of input current measurements on this ePDU.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputPowerCount		1.3.6.1.4.1.534.6.6.7.3.1.1.7
Number of rows in the inputPowerTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputPlugType		1.3.6.1.4.1.534.6.6.7.3.1.1.8
Identifies which plug is on the input.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other1Phase(100), other2Phase(200), other3Phase(300), iecC14Inlet(101), iecC20Inlet(102), iec316P6(103), iec332P6(104), iec360P6(105), iecC14Plug(106), iecC20Plug(107), nema515(120), nemaL515(121), nema520(122), nemaL520(123), nema615(124), nemaL615(125), nemaL530(126), nema620(127), nemaL620(128), nemaL630(129), cs8265(130), french(150), schuko(151), uk(152), nemaL1420(201), nemaL1430(202), iec516P6(301), iec460P9(302), iec560P9(303), iec532P6(304), iec563P6(306), nemaL1520(320), nemaL2120(321), nemaL1530(322), nemaL2130(323), cs8365(324), nemaL2220(325), nemaL2230(326), bladeUps208V(350), bladeUps400V(351)

inputVoltageTable		1.3.6.1.4.1.534.6.6.7.3.2
A list of input voltage measurements. The number of entries is given by inputVoltageCount.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		InputVoltageEntry

inputVoltageEntry		1.3.6.1.4.1.534.6.6.7.3.2.1
An entry for a particular input voltage measurement.
Status: current	Access: not-accessible
OBJECT-TYPE
	InputVoltageEntry

inputVoltageIndex		1.3.6.1.4.1.534.6.6.7.3.2.1.1
A unique value for each input voltage measurement. Its value ranges from 1 to inputVoltageCount.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32	1..3

inputVoltageMeasType		1.3.6.1.4.1.534.6.6.7.3.2.1.2
Value indicates what input voltage is being measured in this table row - single phase voltage, phase 1 to neutral, phase 2 to neutral, phase 3 to neutral, phase 1 to phase 2, phase 2 to phase 3, or phase 3 to phase 1.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	singlePhase(1), phase1toN(2), phase2toN(3), phase3toN(4), phase1to2(5), phase2to3(6), phase3to1(7)

inputVoltage		1.3.6.1.4.1.534.6.6.7.3.2.1.3
An input voltage measurement value. Units are millivolts.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputVoltageThStatus		1.3.6.1.4.1.534.6.6.7.3.2.1.4
Status of the measured input voltage relative to the configured thresholds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	good(0), lowWarning(1), lowCritical(2), highWarning(3), highCritical(4)

inputVoltageThLowerWarning		1.3.6.1.4.1.534.6.6.7.3.2.1.5
Lower warning threshold. Units are millivolts. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..500000

inputVoltageThLowerCritical		1.3.6.1.4.1.534.6.6.7.3.2.1.6
Lower critical threshold. Units are millivolts. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..500000

inputVoltageThUpperWarning		1.3.6.1.4.1.534.6.6.7.3.2.1.7
Upper warning threshold. Units are millivolts. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..500000

inputVoltageThUpperCritical		1.3.6.1.4.1.534.6.6.7.3.2.1.8
Upper critical threshold. Units are millivolts. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..500000

inputCurrentTable		1.3.6.1.4.1.534.6.6.7.3.3
A list of input current measurements. The number of entries is given by inputCurrentCount.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		InputCurrentEntry

inputCurrentEntry		1.3.6.1.4.1.534.6.6.7.3.3.1
An entry for a particular input current measurement.
Status: current	Access: not-accessible
OBJECT-TYPE
	InputCurrentEntry

inputCurrentIndex		1.3.6.1.4.1.534.6.6.7.3.3.1.1
A unique value for each input current measurement. Its value ranges from 1 to inputCurrentCount.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32	1..4

inputCurrentMeasType		1.3.6.1.4.1.534.6.6.7.3.3.1.2
Which input wire is being measured in this table row - single phase, neutral, phase 1, phase 2, or phase 3.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	singlePhase(1), neutral(2), phase1(3), phase2(4), phase3(5)

inputCurrentCapacity		1.3.6.1.4.1.534.6.6.7.3.3.1.3
Rated current capacity of the input. A negative value indicates that the hardware current capacity is unknown. Units are milliamps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputCurrent		1.3.6.1.4.1.534.6.6.7.3.3.1.4
An input current measurement value. Units are milliamps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputCurrentThStatus		1.3.6.1.4.1.534.6.6.7.3.3.1.5
Status of the measured input current relative to the configured thresholds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	good(0), lowWarning(1), lowCritical(2), highWarning(3), highCritical(4)

inputCurrentThLowerWarning		1.3.6.1.4.1.534.6.6.7.3.3.1.6
Lower warning threshold. Units are milliamps. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..100000

inputCurrentThLowerCritical		1.3.6.1.4.1.534.6.6.7.3.3.1.7
Lower critical threshold. Units are milliamps. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..100000

inputCurrentThUpperWarning		1.3.6.1.4.1.534.6.6.7.3.3.1.8
Upper warning threshold. Units are milliamps. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..100000

inputCurrentThUpperCritical		1.3.6.1.4.1.534.6.6.7.3.3.1.9
Upper critical threshold. Units are milliamps. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..100000

inputCurrentCrestFactor		1.3.6.1.4.1.534.6.6.7.3.3.1.10
Current crest factor. Units are in milli, for example a crest factor of 1.414 will be returned as 1414. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputCurrentPercentLoad		1.3.6.1.4.1.534.6.6.7.3.3.1.11
Current percent load, based on the rated current capacity. Units are percentage, for example 80% will be returned as 80. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputPowerTable		1.3.6.1.4.1.534.6.6.7.3.4
A list of input power measurements. The number of entries is given by inputPowerCount.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		InputPowerEntry

inputPowerEntry		1.3.6.1.4.1.534.6.6.7.3.4.1
An entry for an input power measurement.
Status: current	Access: not-accessible
OBJECT-TYPE
	InputPowerEntry

inputPowerIndex		1.3.6.1.4.1.534.6.6.7.3.4.1.1
A unique value for each input power measurement. Its value ranges from 1 to inputPowerCount.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..12

inputPowerMeasType		1.3.6.1.4.1.534.6.6.7.3.4.1.2
Value indicates what is being measured in this table row.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), phase1(1), phase2(2), phase3(3), total(4)

inputVA		1.3.6.1.4.1.534.6.6.7.3.4.1.3
An input VA value. Units are VA. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputWatts		1.3.6.1.4.1.534.6.6.7.3.4.1.4
An input Watts value. Units are Watts. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputWh		1.3.6.1.4.1.534.6.6.7.3.4.1.5
Units are Watt-hours. This object is writable so that it can be reset to 0. When it is written to, the inputWhTimer will be reset updated as well.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967295

inputWhTimer		1.3.6.1.4.1.534.6.6.7.3.4.1.6
Timestamp of when input Watt-hours (inputWh) was last reset.
Status: current	Access: read-only
OBJECT-TYPE
	UnixTimeStamp

inputPowerFactor		1.3.6.1.4.1.534.6.6.7.3.4.1.7
An input PF value. Units are in thousandths, for example a power factor of 0.958 would be returned as 958, and 0.92 would be returned as 920. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputVAR		1.3.6.1.4.1.534.6.6.7.3.4.1.8
An input VAR value. Units are VAR. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputTotalPowerTable		1.3.6.1.4.1.534.6.6.7.3.5
A list of total input power measurements.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		InputTotalPowerEntry

inputTotalPowerEntry		1.3.6.1.4.1.534.6.6.7.3.5.1
An entry for a total input power measurement.
Status: current	Access: not-accessible
OBJECT-TYPE
	InputTotalPowerEntry

inputTotalVA		1.3.6.1.4.1.534.6.6.7.3.5.1.3
An input VA value. Units are VA. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputTotalWatts		1.3.6.1.4.1.534.6.6.7.3.5.1.4
An input Watts value. Units are Watts. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputTotalWh		1.3.6.1.4.1.534.6.6.7.3.5.1.5
Units are Watt-hours. This object is writable so that it can be reset to 0. When it is written to, the inputWhTimer will be reset updated as well.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967295

inputTotalWhTimer		1.3.6.1.4.1.534.6.6.7.3.5.1.6
Timestamp of when input Watt-hours (inputWh) was last reset.
Status: current	Access: read-only
OBJECT-TYPE
	UnixTimeStamp

inputTotalPowerFactor		1.3.6.1.4.1.534.6.6.7.3.5.1.7
An input PF value. Units are in thousandths, for example a power factor of 0.958 would be returned as 958, and 0.92 would be returned as 920. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

inputTotalVAR		1.3.6.1.4.1.534.6.6.7.3.5.1.8
An input VAR value. Units are VAR. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

groupTable		1.3.6.1.4.1.534.6.6.7.5.1
A list of groups. The number of entries is given by groupCount.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		GroupEntry

groupEntry		1.3.6.1.4.1.534.6.6.7.5.1.1
An entry for a particular group.
Status: current	Access: not-accessible
OBJECT-TYPE
	GroupEntry

groupIndex		1.3.6.1.4.1.534.6.6.7.5.1.1.1
A unique value for each group. Its value ranges from 1 to groupCount.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32	1..64

groupID		1.3.6.1.4.1.534.6.6.7.5.1.1.2
Alphanumeric designator for the group. This value may be written on the face of the unit.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(2..4)

groupName		1.3.6.1.4.1.534.6.6.7.5.1.1.3
A descriptive name for the group.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..31)

groupType		1.3.6.1.4.1.534.6.6.7.5.1.1.4
The type of the group.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), breaker1pole(1), breaker2pole(2), breaker3pole(3), outletSection(4), userDefined(5)

groupBreakerStatus		1.3.6.1.4.1.534.6.6.7.5.1.1.5
Only applicable to breaker-groups. Indicates whether a breaker is turned off or on.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(0), breakerOn(1), breakerOff(2)

groupChildCount		1.3.6.1.4.1.534.6.6.7.5.1.1.6
Number of children for this group.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

groupChildTable		1.3.6.1.4.1.534.6.6.7.5.2
A list of children for this group. For example, this table will link to all of the outlets that are contained in a particular group.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		GroupChildEntry

groupChildEntry		1.3.6.1.4.1.534.6.6.7.5.2.1
An entry for a particular child.
Status: current	Access: not-accessible
OBJECT-TYPE
	GroupChildEntry

groupChildIndex		1.3.6.1.4.1.534.6.6.7.5.2.1.1
A unique value for each child. Its value ranges from 1 to groupChildCount.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..32

groupChildType		1.3.6.1.4.1.534.6.6.7.5.2.1.2
The type of the child.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), section(2), custom(3), outlet(4)

groupChildOID		1.3.6.1.4.1.534.6.6.7.5.2.1.3
Object ID of a child object.
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

groupVoltageTable		1.3.6.1.4.1.534.6.6.7.5.3
A list of group voltage measurements. There can be only one voltage measurement for each group.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		GroupVoltageEntry

groupVoltageEntry		1.3.6.1.4.1.534.6.6.7.5.3.1
An entry for a group voltage measurement.
Status: current	Access: not-accessible
OBJECT-TYPE
	GroupVoltageEntry

groupVoltageMeasType		1.3.6.1.4.1.534.6.6.7.5.3.1.2
Value indicates what voltage is being measured in this table row.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), singlePhase(1), phase1toN(2), phase2toN(3), phase3toN(4), phase1to2(5), phase2to3(6), phase3to1(7)

groupVoltage		1.3.6.1.4.1.534.6.6.7.5.3.1.3
Units are millivolts.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

groupVoltageThStatus		1.3.6.1.4.1.534.6.6.7.5.3.1.4
Status of the measured group voltage relative to the configured thresholds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	good(0), lowWarning(1), lowCritical(2), highWarning(3), highCritical(4)

groupVoltageThLowerWarning		1.3.6.1.4.1.534.6.6.7.5.3.1.5
Lower warning threshold. Units are millivolts. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..500000

groupVoltageThLowerCritical		1.3.6.1.4.1.534.6.6.7.5.3.1.6
Lower critical threshold. Units are millivolts. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..500000

groupVoltageThUpperWarning		1.3.6.1.4.1.534.6.6.7.5.3.1.7
Upper warning threshold. Units are millivolts. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..500000

groupVoltageThUpperCritical		1.3.6.1.4.1.534.6.6.7.5.3.1.8
Upper critical threshold. Units are millivolts. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..500000

groupCurrentTable		1.3.6.1.4.1.534.6.6.7.5.4
A list of group current measurements. There can be only one current measurement for each group.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		GroupCurrentEntry

groupCurrentEntry		1.3.6.1.4.1.534.6.6.7.5.4.1
An entry for a group current measurement.
Status: current	Access: not-accessible
OBJECT-TYPE
	GroupCurrentEntry

groupCurrentCapacity		1.3.6.1.4.1.534.6.6.7.5.4.1.2
Rated current capacity of the group. Units are milliamps. A negative value indicates that the hardware current capacity is unknown (it will always be unknown for custom groups).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

groupCurrent		1.3.6.1.4.1.534.6.6.7.5.4.1.3
A group current measurement value. Units are milliamps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

groupCurrentThStatus		1.3.6.1.4.1.534.6.6.7.5.4.1.4
Status of the measured group current relative to the configured thresholds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	good(0), lowWarning(1), lowCritical(2), highWarning(3), highCritical(4)

groupCurrentThLowerWarning		1.3.6.1.4.1.534.6.6.7.5.4.1.5
Lower warning threshold. Units are milliamps. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..100000

groupCurrentThLowerCritical		1.3.6.1.4.1.534.6.6.7.5.4.1.6
Lower critical threshold. Units are milliamps. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..100000

groupCurrentThUpperWarning		1.3.6.1.4.1.534.6.6.7.5.4.1.7
Upper warning threshold. Units are milliamps. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..100000

groupCurrentThUpperCritical		1.3.6.1.4.1.534.6.6.7.5.4.1.8
Upper critical threshold. Units are milliamps. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..100000

groupCurrentCrestFactor		1.3.6.1.4.1.534.6.6.7.5.4.1.9
Current crest factor. Units are in milli, for example a crest factor of 1.414 will be returned as 1414. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

groupCurrentPercentLoad		1.3.6.1.4.1.534.6.6.7.5.4.1.10
Current percent load, based on the rated current capacity. Units are percentage, for example 80% will be returned as 80. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

groupPowerTable		1.3.6.1.4.1.534.6.6.7.5.5
A list of group power measurements. There can be only one power measurement for each group.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		GroupPowerEntry

groupPowerEntry		1.3.6.1.4.1.534.6.6.7.5.5.1
An entry for a group power measurement.
Status: current	Access: not-accessible
OBJECT-TYPE
	GroupPowerEntry

groupVA		1.3.6.1.4.1.534.6.6.7.5.5.1.2
A group VA value. Units are VA. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

groupWatts		1.3.6.1.4.1.534.6.6.7.5.5.1.3
A group Watts value. Units are Watts. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

groupWh		1.3.6.1.4.1.534.6.6.7.5.5.1.4
Units are Watt-hours. This object is writable so that it can be reset to 0. When it is written to, the inputWhTotalTimer will be reset to 0 as well.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967295

groupWhTimer		1.3.6.1.4.1.534.6.6.7.5.5.1.5
Timestamp of when group Watt-hours (groupWh) was last reset.
Status: current	Access: read-only
OBJECT-TYPE
	UnixTimeStamp

groupPowerFactor		1.3.6.1.4.1.534.6.6.7.5.5.1.6
A group PF value. Units are in thousandths, for example a power factor of 0.958 would be returned as 958, and 0.92 would be returned as 920. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

groupVAR		1.3.6.1.4.1.534.6.6.7.5.5.1.7
A group VAR value. Units are VAR. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

groupControlTable		1.3.6.1.4.1.534.6.6.7.5.6
A list of controllable groups.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		GroupControlEntry

groupControlEntry		1.3.6.1.4.1.534.6.6.7.5.6.1
An entry for a controllable group.
Status: current	Access: not-accessible
OBJECT-TYPE
	GroupControlEntry

groupControlStatus		1.3.6.1.4.1.534.6.6.7.5.6.1.2
Current state of a controlled group. A value of 'mixed' means that that the outlets within the group have differing states.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1), rebooting(2), mixed(3)

groupControlOffCmd		1.3.6.1.4.1.534.6.6.7.5.6.1.3
Group-level outlet control command. Once the command is issued, the outlets in the group will turn Off immediately. 0-n : Time in seconds until the group command is issued -1 : Cancel a pending group-level Off command When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control commands. These will respond with an error if a command value of > 0 is written to this object.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..99999

groupControl0nCmd		1.3.6.1.4.1.534.6.6.7.5.6.1.4
Group-level outlet control command. Once the command is issued, the outlets in the group will turn On immediately. 0-n : Time in seconds until the group command is issued -1 : Cancel a pending group-level On command When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control commands. These will respond with an error if a command value of > 0 is written to this object.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..99999

groupControlRebootCmd		1.3.6.1.4.1.534.6.6.7.5.6.1.5
Group-level outlet control command. For outlets that are On prior to the Reboot command, they will switch Off immediately when the command is issued, remain Off for outletControlRebootOffTime seconds, and then turn back On. For outlets that are Off prior to the Reboot command, they will turn On after a delay of outletControlRebootOffTime seconds from when the command is issued. 0-n : Time in seconds until the Reboot command is issued -1 : Cancel a pending group-level Reboot command When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control commands. These will respond with an error if a command value of > 0 is written to this object.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..0

outletTable		1.3.6.1.4.1.534.6.6.7.6.1
A list of outlets. The number of entries is given by outletCount.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OutletEntry

outletEntry		1.3.6.1.4.1.534.6.6.7.6.1.1
An entry for a particular outlet.
Status: current	Access: not-accessible
OBJECT-TYPE
	OutletEntry

outletIndex		1.3.6.1.4.1.534.6.6.7.6.1.1.1
A unique value for each outlet. its value ranges from 1 to outletCount.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32	1..64

outletID		1.3.6.1.4.1.534.6.6.7.6.1.1.2
Alphanumeric designator for the outlet.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(2..4)

outletName		1.3.6.1.4.1.534.6.6.7.6.1.1.3
A descriptive name for the outlet.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..31)

outletParentCount		1.3.6.1.4.1.534.6.6.7.6.1.1.4
Number of parents for this outlet.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

outletType		1.3.6.1.4.1.534.6.6.7.6.1.1.5
The physical type of outlet.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), iecC13(1), iecC19(2), uk(10), french(11), schuko(12), nema515(20), nema51520(21), nema520(22), nemaL520(23), nemaL530(24), nema615(25), nema620(26), nemaL620(27), nemaL630(28), nemaL715(29), rf203p277(30)

outletParentTable		1.3.6.1.4.1.534.6.6.7.6.2
A list of parents for this outlet. For example, this table will link to all of the groups that have this outlet as a child.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OutletParentEntry

outletParentEntry		1.3.6.1.4.1.534.6.6.7.6.2.1
An entry for a particular parent.
Status: current	Access: not-accessible
OBJECT-TYPE
	OutletParentEntry

outletParentIndex		1.3.6.1.4.1.534.6.6.7.6.2.1.1
A unique value for each parent. Its value ranges from 1 to outletParentCount.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..32

outletParentType		1.3.6.1.4.1.534.6.6.7.6.2.1.2
The type of the parent.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), breaker(1), section(2), custom(3)

outletParentOID		1.3.6.1.4.1.534.6.6.7.6.2.1.3
Object ID of a parent object.
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

outletVoltageTable		1.3.6.1.4.1.534.6.6.7.6.3
A list of outlet voltage measurements.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OutletVoltageEntry

outletVoltageEntry		1.3.6.1.4.1.534.6.6.7.6.3.1
An entry for an outlet voltage measurement.
Status: current	Access: not-accessible
OBJECT-TYPE
	OutletVoltageEntry

outletVoltage		1.3.6.1.4.1.534.6.6.7.6.3.1.2
Units are millivolts.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

outletVoltageThStatus		1.3.6.1.4.1.534.6.6.7.6.3.1.3
Status of the measured outlet voltage relative to the configured thresholds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	good(0), lowWarning(1), lowCritical(2), highWarning(3), highCritical(4)

outletVoltageThLowerWarning		1.3.6.1.4.1.534.6.6.7.6.3.1.4
Lower warning threshold. Units are millivolts. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..500000

outletVoltageThLowerCritical		1.3.6.1.4.1.534.6.6.7.6.3.1.5
Lower critical threshold. Units are millivolts. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..500000

outletVoltageThUpperWarning		1.3.6.1.4.1.534.6.6.7.6.3.1.6
Upper warning threshold. Units are millivolts. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..500000

outletVoltageThUpperCritical		1.3.6.1.4.1.534.6.6.7.6.3.1.7
Upper critical threshold. Units are millivolts. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..500000

outletCurrentTable		1.3.6.1.4.1.534.6.6.7.6.4
A list of outlet current measurements.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OutletCurrentEntry

outletCurrentEntry		1.3.6.1.4.1.534.6.6.7.6.4.1
An entry for an outlet current measurement.
Status: current	Access: not-accessible
OBJECT-TYPE
	OutletCurrentEntry

outletCurrentCapacity		1.3.6.1.4.1.534.6.6.7.6.4.1.2
Rated current capacity of the outlet. Units are milliamps. A negative value indicates that the hardware current capacity is unknown.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

outletCurrent		1.3.6.1.4.1.534.6.6.7.6.4.1.3
An outlet current measurement value. Units are milliamps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

outletCurrentThStatus		1.3.6.1.4.1.534.6.6.7.6.4.1.4
Status of the measured outlet current relative to the configured thresholds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	good(0), lowWarning(1), lowCritical(2), highWarning(3), highCritical(4)

outletCurrentThLowerWarning		1.3.6.1.4.1.534.6.6.7.6.4.1.5
Lower warning threshold. Units are milliamps. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..100000

outletCurrentThLowerCritical		1.3.6.1.4.1.534.6.6.7.6.4.1.6
Lower critical threshold. Units are milliamps. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..100000

outletCurrentThUpperWarning		1.3.6.1.4.1.534.6.6.7.6.4.1.7
Upper warning threshold. Units are milliamps. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..100000

outletCurrentThUpperCritical		1.3.6.1.4.1.534.6.6.7.6.4.1.8
Upper critical threshold. Units are milliamps. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..100000

outletCurrentCrestFactor		1.3.6.1.4.1.534.6.6.7.6.4.1.9
Current crest factor. Units are in milli, for example a crest factor of 1.414 will be returned as 1414. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

outletCurrentPercentLoad		1.3.6.1.4.1.534.6.6.7.6.4.1.10
Current percent load, based on the rated current capacity. Units are percentage, for example 80% will be returned as 80. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

outletPowerTable		1.3.6.1.4.1.534.6.6.7.6.5
A list of outlet power measurements.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OutletPowerEntry

outletPowerEntry		1.3.6.1.4.1.534.6.6.7.6.5.1
An entry for an outlet power measurement.
Status: current	Access: not-accessible
OBJECT-TYPE
	OutletPowerEntry

outletVA		1.3.6.1.4.1.534.6.6.7.6.5.1.2
An outlet VA value. Units are VA. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

outletWatts		1.3.6.1.4.1.534.6.6.7.6.5.1.3
An outlet Watts value. Units are Watts. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

outletWh		1.3.6.1.4.1.534.6.6.7.6.5.1.4
Units are Watt-hours. This object is writable so that it can be reset to 0. When it is written to, the inputWhTotalTimer will be reset to 0 as well.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967295

outletWhTimer		1.3.6.1.4.1.534.6.6.7.6.5.1.5
Timestamp of when outlet Watt-hours (outletWh) was last reset.
Status: current	Access: read-only
OBJECT-TYPE
	UnixTimeStamp

outletPowerFactor		1.3.6.1.4.1.534.6.6.7.6.5.1.6
An outlet PF value. Units are in thousandths, for example a power factor of 0.958 would be returned as 958, and 0.92 would be returned as 920. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

outletVAR		1.3.6.1.4.1.534.6.6.7.6.5.1.7
An outlet VAR value. Units are VAR. A negative value indicates that this object is not available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

outletControlTable		1.3.6.1.4.1.534.6.6.7.6.6
A list of controllable outlets.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OutletControlEntry

outletControlEntry		1.3.6.1.4.1.534.6.6.7.6.6.1
An entry for a controllable outlet.
Status: current	Access: not-accessible
OBJECT-TYPE
	OutletControlEntry

outletControlStatus		1.3.6.1.4.1.534.6.6.7.6.6.1.2
Current state of a controlled outlet.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1), pendingOff(2), pendingOn(3)

outletControlOffCmd		1.3.6.1.4.1.534.6.6.7.6.6.1.3
Outlet control command. Once the command is issued, the outlet will turn Off immediately. 0-n : Time in seconds until the outlet command is issued -1 : Cancel a pending outlet Off command When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control commands. These will respond with an error if a command value of > 0 is written to this object.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..99999

outletControlOnCmd		1.3.6.1.4.1.534.6.6.7.6.6.1.4
Outlet control command. Once the command is issued, the outlet will turn On immediately. 0-n : Time in seconds until the outlet command is issued -1 : Cancel a pending outlet On command When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control commands. These will respond with an error if a command value of > 0 is written to this object.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..99999

outletControlRebootCmd		1.3.6.1.4.1.534.6.6.7.6.6.1.5
Outlet control command. For outlets that are On prior to this Reboot command, they will switch Off immediately when the command is issued, remain Off for outletControlRebootOffTime seconds, and then turn back On. For outlets that are Off prior to the Reboot command, they will turn On after a delay of outletControlRebootOffTime seconds from when the command is issued. 0-n : Time in seconds until the Reboot command is issued -1 : Cancel a pending outlet Reboot command When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control commands. These will respond with an error if a command value of > 0 is written to this object.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..99999

outletControlPowerOnState		1.3.6.1.4.1.534.6.6.7.6.6.1.6
Determines the outlet state when power is applied to the unit. 0 : not restart at device startup 1 : should sequence back ON in line with outletControlSequenceTime 2 : should take the state the outlet had when power was lost. If the state was ON, should sequence back ON in line with outletControlSequenceTime.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(0), on(1), lastState(2)

outletControlSequenceDelay		1.3.6.1.4.1.534.6.6.7.6.6.1.7
Time delay in seconds from when a Global Sequence On command is issued to when the command is executed on this outlet. This delay is also used as a power-on delay. Set to -1 to exclude this outlet from Global Sequence On commands.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..99999

outletControlRebootOffTime		1.3.6.1.4.1.534.6.6.7.6.6.1.8
Time delay in seconds that the outlet should remain in the Off state when executing a Reboot command.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..99999

outletControlSwitchable		1.3.6.1.4.1.534.6.6.7.6.6.1.9
Determines the outlet capability to be controlled On/Off from the communication channels. 1 : control On/Off enabled 2 : control On/Off disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	switchable(1), notSwitchable(2)

outletControlShutoffDelay		1.3.6.1.4.1.534.6.6.7.6.6.1.10
Time delay in seconds that could be taken in account before shutting of the outlet. An application which need to shutoff properly an outlet will read this parameter first then write it to the command outletControlOffCmd.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..99999

temperatureTable		1.3.6.1.4.1.534.6.6.7.7.1
A list of temperature probe measurements. The number of entries is given by temperatureCount.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TemperatureEntry

temperatureEntry		1.3.6.1.4.1.534.6.6.7.7.1.1
An entry for a temperature measurement.
Status: current	Access: not-accessible
OBJECT-TYPE
	TemperatureEntry

temperatureIndex		1.3.6.1.4.1.534.6.6.7.7.1.1.1
A unique value for each temperature probe measurement. Its value ranges from 1 to temperatureCount.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32	1..2

temperatureName		1.3.6.1.4.1.534.6.6.7.7.1.1.2
A descriptive name for the temperature probe.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..31)

temperatureProbeStatus		1.3.6.1.4.1.534.6.6.7.7.1.1.3
Indicates whether a probe is connected or not.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	bad(-1), disconnected(0), connected(1)

temperatureValue		1.3.6.1.4.1.534.6.6.7.7.1.1.4
Units are in tenths of a degree according to the scale specified by temperatureScale (either Fahrenheit or Celsius). Divide by ten to get degrees.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

temperatureThStatus		1.3.6.1.4.1.534.6.6.7.7.1.1.5
Status of the measured temperature relative to the configured thresholds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	good(0), lowWarning(1), lowCritical(2), highWarning(3), highCritical(4)

temperatureThLowerWarning		1.3.6.1.4.1.534.6.6.7.7.1.1.6
Lower warning threshold. Units are tenths of a degree. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..150000

temperatureThLowerCritical		1.3.6.1.4.1.534.6.6.7.7.1.1.7
Lower critical threshold. Units are tenths of a degree. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..150000

temperatureThUpperWarning		1.3.6.1.4.1.534.6.6.7.7.1.1.8
Upper warning threshold. Units are tenths of a degree. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..150000

temperatureThUpperCritical		1.3.6.1.4.1.534.6.6.7.7.1.1.9
Upper critical threshold. Units are tenths of a degree. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..150000

humidityTable		1.3.6.1.4.1.534.6.6.7.7.2
A list of humidity probe measurements. The number of entries is given by humidityCount.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HumidityEntry

humidityEntry		1.3.6.1.4.1.534.6.6.7.7.2.1
An entry for a humidity measurement.
Status: current	Access: not-accessible
OBJECT-TYPE
	HumidityEntry

humidityIndex		1.3.6.1.4.1.534.6.6.7.7.2.1.1
A unique value for each humidity probe measurement. Its value ranges from 1 to humidityCount.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32	1..2

humidityName		1.3.6.1.4.1.534.6.6.7.7.2.1.2
A descriptive name for the humidity probe.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..31)

humidityProbeStatus		1.3.6.1.4.1.534.6.6.7.7.2.1.3
Indicates whether a probe is connected or not.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	bad(-1), disconnected(0), connected(1)

humidityValue		1.3.6.1.4.1.534.6.6.7.7.2.1.4
Units are tenths of a percent relative humidity. Divide the value by 10 to get %RH.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

humidityThStatus		1.3.6.1.4.1.534.6.6.7.7.2.1.5
Status of the measured humidity relative to the configured thresholds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	good(0), lowWarning(1), lowCritical(2), highWarning(3), highCritical(4)

humidityThLowerWarning		1.3.6.1.4.1.534.6.6.7.7.2.1.6
Lower warning threshold. Units are 0.1 %RH. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..1000

humidityThLowerCritical		1.3.6.1.4.1.534.6.6.7.7.2.1.7
Lower critical threshold. Units are 0.1 %RH. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..1000

humidityThUpperWarning		1.3.6.1.4.1.534.6.6.7.7.2.1.8
Upper warning threshold. Units are 0.1 %RH. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..1000

humidityThUpperCritical		1.3.6.1.4.1.534.6.6.7.7.2.1.9
Upper critical threshold. Units are 0.1 %RH. A negative value indicates that this object is not available.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..1000

contactTable		1.3.6.1.4.1.534.6.6.7.7.3
A list of contact sensors. The number of entries is given by contactCount.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ContactEntry

contactEntry		1.3.6.1.4.1.534.6.6.7.7.3.1
An entry for a contact sensor
Status: current	Access: not-accessible
OBJECT-TYPE
	ContactEntry

contactIndex		1.3.6.1.4.1.534.6.6.7.7.3.1.1
A unique value for each contact sensor. Its value ranges from 1 to contactCount.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32	1..3

contactName		1.3.6.1.4.1.534.6.6.7.7.3.1.2
A descriptive name for the contact sensor.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..31)

contactProbeStatus		1.3.6.1.4.1.534.6.6.7.7.3.1.3
Indicates whether a probe is connected or not. Will not be returned if the contact sensor is internal to the ePDU, in that case only contactState should be read.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	bad(-1), disconnected(0), connected(1)

contactState		1.3.6.1.4.1.534.6.6.7.7.3.1.4
The state of the contact sensor.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	contactBad(-1), contactOpen(0), contactClosed(1)

eatonEpduCompliances		1.3.6.1.4.1.534.6.6.7.25.1
The requirements for conforming to the ePDU MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

epduRequiredGroup		1.3.6.1.4.1.534.6.6.7.25.5.1
Minimal objects are required to conform to this MIB.
Status: current	Access: read-only
OBJECT-GROUP

epduOptionalGroup		1.3.6.1.4.1.534.6.6.7.25.5.2
Most objects in this MIB are optional.
Status: current	Access: read-only
OBJECT-GROUP

epduNotifyGroup		1.3.6.1.4.1.534.6.6.7.25.5.3
These notifications will be supported depending on the features of the ePDU. Check the web interface for options to turn these notifications on/off. If an option is not listed, then the ePDU likely does not support that notification.
Status: current	Access: read-only
NOTIFICATION-GROUP