DeltaUPS-MIB

File: DeltaUPS-MIB.mib (46507 bytes)

Imported modules

RFC1155-SMI	RFC1213-MIB	RFC-1212
RFC-1215

Imported symbols

enterprises	IpAddress	DisplayString
OBJECT-TYPE	TRAP-TYPE

Defined Values

delta		1.3.6.1.4.1.2254
OBJECT IDENTIFIER

ups		1.3.6.1.4.1.2254.2
OBJECT IDENTIFIER

upsv4		1.3.6.1.4.1.2254.2.4
OBJECT IDENTIFIER

dupsIdent		1.3.6.1.4.1.2254.2.4.1
OBJECT IDENTIFIER

dupsControl		1.3.6.1.4.1.2254.2.4.2
OBJECT IDENTIFIER

dupsConfig		1.3.6.1.4.1.2254.2.4.3
OBJECT IDENTIFIER

dupsInput		1.3.6.1.4.1.2254.2.4.4
OBJECT IDENTIFIER

dupsOutput		1.3.6.1.4.1.2254.2.4.5
OBJECT IDENTIFIER

dupsBypass		1.3.6.1.4.1.2254.2.4.6
OBJECT IDENTIFIER

dupsBattery		1.3.6.1.4.1.2254.2.4.7
OBJECT IDENTIFIER

dupsTest		1.3.6.1.4.1.2254.2.4.8
OBJECT IDENTIFIER

dupsAlarm		1.3.6.1.4.1.2254.2.4.9
OBJECT IDENTIFIER

dupsEnvironment		1.3.6.1.4.1.2254.2.4.10
OBJECT IDENTIFIER

dupsTraps		1.3.6.1.4.1.2254.2.4.20
OBJECT IDENTIFIER

dupsIdentManufacturer		1.3.6.1.4.1.2254.2.4.1.1
The name of the UPS manufacturer.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

dupsIdentModel		1.3.6.1.4.1.2254.2.4.1.2
The UPS Model designation.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..31)

dupsIdentUPSSoftwareVersion		1.3.6.1.4.1.2254.2.4.1.3
The UPS firmware/software version(s). This variable may or may not has the same value as upsIdentAgentSoftwareVersion in some implementations.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..15)

dupsIdentAgentSoftwareVersion		1.3.6.1.4.1.2254.2.4.1.4
The UPS agent software version. This variable may or may not has the same value as upsIdentUPSSoftwareVersion in some implementations.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..15)

dupsIdentName		1.3.6.1.4.1.2254.2.4.1.5
A string identifying the UPS. This object should be set by the administrator.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..63)

dupsAttachedDevices		1.3.6.1.4.1.2254.2.4.1.6
A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..63)

dupsRatingOutputVA		1.3.6.1.4.1.2254.2.4.1.7
The magnitude of the nominal output VA rating.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsRatingOutputVoltage		1.3.6.1.4.1.2254.2.4.1.8
The magnitude of the nominal output voltage rating.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsRatingOutputFrequency		1.3.6.1.4.1.2254.2.4.1.9
The magnitude of the nominal output frequency rating.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsRatingInputVoltage		1.3.6.1.4.1.2254.2.4.1.10
The magnitude of the nominal input voltage rating.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsRatingInputFrequency		1.3.6.1.4.1.2254.2.4.1.11
The magnitude of the nominal input frequency rating.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsRatingBatteryVoltage		1.3.6.1.4.1.2254.2.4.1.12
The magnitude of the nominal battery voltage rating.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsLowTransferVoltUpBound		1.3.6.1.4.1.2254.2.4.1.13
The minimum input line voltage upper bound allowed before the UPS system transfers to battery backup.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsLowTransferVoltLowBound		1.3.6.1.4.1.2254.2.4.1.14
The minimum input line voltage lower bound allowed before the UPS system transfers to battery backup.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsHighTransferVoltUpBound		1.3.6.1.4.1.2254.2.4.1.15
The maximum input line voltage upper bound allowed before the UPS system transfers to battery backup.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsHighTransferVoltLowBound		1.3.6.1.4.1.2254.2.4.1.16
The maximum input line voltage lower bound allowed before the UPS system transfers to battery backup.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsLowBattTime		1.3.6.1.4.1.2254.2.4.1.17
Minutes, time from low battery to low battery shutdown.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutletRelays		1.3.6.1.4.1.2254.2.4.1.18
Number of outlet relay. If it is 0, the function is not available for the UPS.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsType		1.3.6.1.4.1.2254.2.4.1.19
Indicate the UPS type.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on-line(1), off-line(2), line-interactive(3), phase3(4), splite-phase(5)

dupsShutdownType		1.3.6.1.4.1.2254.2.4.2.1
This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	output(1), system(2)

dupsAutoReboot		1.3.6.1.4.1.2254.2.4.2.2
In backup mode, the UPS may shutdown normally by SDA command, dry-contact remote shutdown signal or low battery shutdown. This command is used to determine the unit should restart or not next time when the power restores
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

dupsShutdownAction		1.3.6.1.4.1.2254.2.4.2.3
If the value is greater than 0 the UPS performs shutdown action that defined by ShutdownType after the seconds. 0, aborted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dupsRestartAction		1.3.6.1.4.1.2254.2.4.2.4
UPS will restart after the indicated number of minutes. -1, aborted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dupsSetOutletRelay		1.3.6.1.4.1.2254.2.4.2.5
Indicate which outlet relay, from 1,2,3... .
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dupsRelayOffDelay		1.3.6.1.4.1.2254.2.4.2.6
Turn the relay off after the seconds. The relay was indicated by SetOutletRelay.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dupsRelayOnDelay		1.3.6.1.4.1.2254.2.4.2.7
Turn the relay on after the seconds. The relay was indicated by SetOutletRelay.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dupsConfigBuzzerAlarm		1.3.6.1.4.1.2254.2.4.3.1
UPS will keep silence but will alarm again when next power event is occurred
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	alarm(1), silence(2)

dupsConfigBuzzerState		1.3.6.1.4.1.2254.2.4.3.2
If it is disabled then the UPS is always muted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

dupsConfigSensitivity		1.3.6.1.4.1.2254.2.4.3.3
The seneitivity of the UPS to utility line abnormalities or noises.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(0), reduced(1), low(2)

dupsConfigLowVoltageTransferPoint		1.3.6.1.4.1.2254.2.4.3.4
The minimum input line voltage allowed before the UPS system transfers to battery backup.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dupsConfigHighVoltageTransferPoint		1.3.6.1.4.1.2254.2.4.3.5
The maximum line voltage allowed before the UPS system transfers to battery backup.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dupsConfigShutdownOSDelay		1.3.6.1.4.1.2254.2.4.3.6
The operating system shutdown delay time when the input power fail. -1 will disable this option.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dupsConfigUPSBootDelay		1.3.6.1.4.1.2254.2.4.3.7
Delay the UPS startup after power restores. The power quality may not stable when power restores, this feature let the UPS wait a period of time to startup the system.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dupsConfigExternalBatteryPack		1.3.6.1.4.1.2254.2.4.3.8
Indicate the number of external battery pack.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dupsInputNumLines		1.3.6.1.4.1.2254.2.4.4.1
The number of input lines utilized in this device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsInputFrequency1		1.3.6.1.4.1.2254.2.4.4.2
The current input line 1 frequency to the UPS system in 1/10 Hz.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsInputVoltage1		1.3.6.1.4.1.2254.2.4.4.3
The Input line 1 voltage of the UPS system in 1/10 V.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsInputCurrent1		1.3.6.1.4.1.2254.2.4.4.4
The Input line 1 current to the UPS system in 1/10 A.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsInputFrequency2		1.3.6.1.4.1.2254.2.4.4.5
The current input line 2 frequency to the UPS system in 1/10 Hz.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsInputVoltage2		1.3.6.1.4.1.2254.2.4.4.6
The Input line 2 voltage of the UPS system in 1/10 V.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsInputCurrent2		1.3.6.1.4.1.2254.2.4.4.7
The Input line 2 current to the UPS system in 1/10 A.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsInputFrequency3		1.3.6.1.4.1.2254.2.4.4.8
The current input line 3 frequency to the UPS system in 1/10 Hz.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsInputVoltage3		1.3.6.1.4.1.2254.2.4.4.9
The Input line 3 voltage of the UPS system in 1/10 V.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsInputCurrent3		1.3.6.1.4.1.2254.2.4.4.10
The Input line 3 current to the UPS system in 1/10 A.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputSource		1.3.6.1.4.1.2254.2.4.5.1
The present source of output power. The enumeration none(7) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	normal(0), battery(1), bypass(2), reducing(3), boosting(4), manualBypass(5), other(6), none(7)

dupsOutputFrequency		1.3.6.1.4.1.2254.2.4.5.2
The present output frequency in 1/10 Hz.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputNumLines		1.3.6.1.4.1.2254.2.4.5.3
The number of output lines utilized in this device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputVoltage1		1.3.6.1.4.1.2254.2.4.5.4
The Output line 1 voltage of the UPS system in 1/10 V.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputCurrent1		1.3.6.1.4.1.2254.2.4.5.5
The Output line 1 current of the UPS system in 1/10 A.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputPower1		1.3.6.1.4.1.2254.2.4.5.6
The Output line 1 real power of the UPS system in watts.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputLoad1		1.3.6.1.4.1.2254.2.4.5.7
The current UPS output line 1 load expressed in percent of rated capacity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputVoltage2		1.3.6.1.4.1.2254.2.4.5.8
The Output line 2 voltage of the UPS system in 1/10 V.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputCurrent2		1.3.6.1.4.1.2254.2.4.5.9
The Output line 2 current of the UPS system in 1/10 A.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputPower2		1.3.6.1.4.1.2254.2.4.5.10
The Output line 2 real power of the UPS system in watts.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputLoad2		1.3.6.1.4.1.2254.2.4.5.11
The current UPS output line 2 load expressed in percent of rated capacity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputVoltage3		1.3.6.1.4.1.2254.2.4.5.12
The Output line 3 voltage of the UPS system in 1/10 V.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputCurrent3		1.3.6.1.4.1.2254.2.4.5.13
The Output line 3 current of the UPS system in 1/10 A.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputPower3		1.3.6.1.4.1.2254.2.4.5.14
The Output line 3 real power of the UPS system in watts.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsOutputLoad3		1.3.6.1.4.1.2254.2.4.5.15
The current UPS output line 3 load expressed in percent of rated capacity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBypassFrequency		1.3.6.1.4.1.2254.2.4.6.1
The present bypass frequency in 1/10 Hz.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBypassNumLines		1.3.6.1.4.1.2254.2.4.6.2
The number of bypass lines utilized in this device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBypassVoltage1		1.3.6.1.4.1.2254.2.4.6.3
The bypass line 1 voltage of the UPS system in 1/10 V.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBypassCurrent1		1.3.6.1.4.1.2254.2.4.6.4
The bypass line 1 current of the UPS system in 1/10 A.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBypassPower1		1.3.6.1.4.1.2254.2.4.6.5
The bypass line 1 real power of the UPS system in watts.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBypassVoltage2		1.3.6.1.4.1.2254.2.4.6.6
The bypass line 2 voltage of the UPS system in 1/10 V.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBypassCurrent2		1.3.6.1.4.1.2254.2.4.6.7
The bypass line 2 current of the UPS system in 1/10 A.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBypassPower2		1.3.6.1.4.1.2254.2.4.6.8
The bypass line 2 real power of the UPS system in watts.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBypassVoltage3		1.3.6.1.4.1.2254.2.4.6.9
The bypass line 3 voltage of the UPS system in 1/10 V.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBypassCurrent3		1.3.6.1.4.1.2254.2.4.6.10
The bypass line 3 current of the UPS system in 1/10 A.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBypassPower3		1.3.6.1.4.1.2254.2.4.6.11
The bypass line 3 real power of the UPS system in watts.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBatteryCondiction		1.3.6.1.4.1.2254.2.4.7.1
The indication of the capacity remaining in the UPS system's batteries when AC normal.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	good(0), weak(1), replace(2)

dupsBatteryStatus		1.3.6.1.4.1.2254.2.4.7.2
The indication of the capacity remaining in the UPS system's batteries when AC failed. A value of ok indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of low indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of depleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(0), low(1), depleted(2)

dupsBatteryCharge		1.3.6.1.4.1.2254.2.4.7.3
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	floating(0), charging(1), resting(2), discharging(3)

dupsSecondsOnBattery		1.3.6.1.4.1.2254.2.4.7.4
If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBatteryEstimatedTime		1.3.6.1.4.1.2254.2.4.7.5
Estimated time from backup to low battery shutdown.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBatteryVoltage		1.3.6.1.4.1.2254.2.4.7.6
The magnitude of the present battery voltage in 1/10 V.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBatteryCurrent		1.3.6.1.4.1.2254.2.4.7.7
The present battery current in 1/10 A.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsBatteryCapacity		1.3.6.1.4.1.2254.2.4.7.8
An estimate of the battery charge remaining expressed as a percent of full charge.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..100

dupsTemperature		1.3.6.1.4.1.2254.2.4.7.9
The ambient temperature at or near the UPS Battery casing.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsLastReplaceDate		1.3.6.1.4.1.2254.2.4.7.10
The last battery replacement date. The format is YYYYMMDD.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..8)

dupsNextReplaceDate		1.3.6.1.4.1.2254.2.4.7.11
The next battery replacement date. The format is YYYYMMDD.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..8)

dupsTestType		1.3.6.1.4.1.2254.2.4.8.1
Perform the UPS Test procedure.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	abort(0), generalTest(1), batteryTest(2), testFor10sec(3), testUntilBattlow(4)

dupsTestResultsSummary		1.3.6.1.4.1.2254.2.4.8.2
The results of the current or last UPS diagnostics test performed. The values for donePass(1), generalTestFail(3), and batteryTestFail(4) indicate that the test completed either successfully, with a warning, or with an error, respectively.Tests which have not yet concluded are indicated by inProgress(2). The value noTestsInitiated(0) indicates that no previous test results are available.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noTestsInitiated(0), donePass(1), inProgress(2), generalTestFail(3), batteryTestFail(4), deepBatteryTestFail(5)

dupsTestResultsDetail		1.3.6.1.4.1.2254.2.4.8.3
Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

dupsAlarmDisconnect		1.3.6.1.4.1.2254.2.4.9.1
Does the UPS disconnect?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmPowerFail		1.3.6.1.4.1.2254.2.4.9.2
Does the input power fail?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmBatteryLow		1.3.6.1.4.1.2254.2.4.9.3
Are the UPS batteries low?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmLoadWarning		1.3.6.1.4.1.2254.2.4.9.4
Does the UPS load percent over the load warning value?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmLoadSeverity		1.3.6.1.4.1.2254.2.4.9.5
Does the UPS load percent over the load severity value?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmLoadOnBypass		1.3.6.1.4.1.2254.2.4.9.6
Does the UPS load on bypass?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmUPSFault		1.3.6.1.4.1.2254.2.4.9.7
Does the UPS general fail?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmBatteryGroundFault		1.3.6.1.4.1.2254.2.4.9.8
Does the UPS battery ground fault?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmTestInProgress		1.3.6.1.4.1.2254.2.4.9.9
Does the UPS test in progress?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmBatteryTestFail		1.3.6.1.4.1.2254.2.4.9.10
Does the UPS test fail?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmFuseFailure		1.3.6.1.4.1.2254.2.4.9.11
Does the UPS fuse failure?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmOutputOverload		1.3.6.1.4.1.2254.2.4.9.12
Does the UPS output overload?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmOutputOverCurrent		1.3.6.1.4.1.2254.2.4.9.13
Does the UPS output overcurrent?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmInverterAbnormal		1.3.6.1.4.1.2254.2.4.9.14
Does the UPS inverter abnormal?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmRectifierAbnormal		1.3.6.1.4.1.2254.2.4.9.15
Does the UPS rectifier abnormal?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmReserveAbnormal		1.3.6.1.4.1.2254.2.4.9.16
Does the UPS reserve abnormal?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmLoadOnReserve		1.3.6.1.4.1.2254.2.4.9.17
Does the UPS load on reserve?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmOverTemperature		1.3.6.1.4.1.2254.2.4.9.18
Does the UPS over heat?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmOutputBad		1.3.6.1.4.1.2254.2.4.9.19
Is the UPS output abnormal?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmBypassBad		1.3.6.1.4.1.2254.2.4.9.20
Is the UPS bypass bad?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmUPSOff		1.3.6.1.4.1.2254.2.4.9.21
Is the UPS in standby mode?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmChargerFail		1.3.6.1.4.1.2254.2.4.9.22
Does the UPS charger fail?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmFanFail		1.3.6.1.4.1.2254.2.4.9.23
Does the UPS fan fail?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmEconomicMode		1.3.6.1.4.1.2254.2.4.9.24
Indicates whether the UPS is in the economic mode.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmOutputOff		1.3.6.1.4.1.2254.2.4.9.25
Indicates whether the UPS output is turned off or not.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmSmartShutdown		1.3.6.1.4.1.2254.2.4.9.26
Indicates whether the Smart Shutdown is in progress.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmEmergencyPowerOff		1.3.6.1.4.1.2254.2.4.9.27
UPS emergency power off.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmUPSShutdown		1.3.6.1.4.1.2254.2.4.9.28
UPS shutdown.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsEnvTemperature		1.3.6.1.4.1.2254.2.4.10.1
The ambient environmental temperature.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsEnvHumidity		1.3.6.1.4.1.2254.2.4.10.2
The environmental humidity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dupsEnvSetTemperatureLimit		1.3.6.1.4.1.2254.2.4.10.3
Alarm dupsAlarmOverTemperature on when the environmental temperature over the value.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dupsEnvSetHumidityLimit		1.3.6.1.4.1.2254.2.4.10.4
Alarm dupsAlarmOverHumidity on when the environmental humidity over the value.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dupsEnvSetEnvRelay1		1.3.6.1.4.1.2254.2.4.10.5
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normalOpen(0), normalClose(1)

dupsEnvSetEnvRelay2		1.3.6.1.4.1.2254.2.4.10.6
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normalOpen(0), normalClose(1)

dupsEnvSetEnvRelay3		1.3.6.1.4.1.2254.2.4.10.7
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normalOpen(0), normalClose(1)

dupsEnvSetEnvRelay4		1.3.6.1.4.1.2254.2.4.10.8
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normalOpen(0), normalClose(1)

dupsAlarmOverEnvTemperature		1.3.6.1.4.1.2254.2.4.10.9
Does the environment over temperature?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmOverEnvHumidity		1.3.6.1.4.1.2254.2.4.10.10
Does the environment over humidity?
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmEnvRelay1		1.3.6.1.4.1.2254.2.4.10.11
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmEnvRelay2		1.3.6.1.4.1.2254.2.4.10.12
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmEnvRelay3		1.3.6.1.4.1.2254.2.4.10.13
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsAlarmEnvRelay4		1.3.6.1.4.1.2254.2.4.10.14
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

dupsCommunicationLost		1
SEVER: Communication with the UPS failed.
TRAP-TYPE

dupsCommunicationEstablished		2
INFORMATION: Communication with the UPS reestablished.
TRAP-TYPE

dupsPowerFail		3
WARNING: Power failed! The UPS is operating on battery power.
TRAP-TYPE

dupsPowerRestored		4
INFORMATION: Power restored! The utility power restored.
TRAP-TYPE

dupsLowBattery		5
SEVER: The UPS batteries are low and will soon be exhausted.
TRAP-TYPE

dupsReturnFromLowBattery		6
INFORMATION: The UPS has returned from a low battery condition.
TRAP-TYPE

dupsLoadWarning		7
INFORMATION: Loading percent of the UPS over the Load Warning value.
TRAP-TYPE

dupsNoLongerLoadWarning		8
INFORMATION: Returnd from Load Warning condition.
TRAP-TYPE

dupsLoadSeverity		9
Warning: Loading percent of the UPS over the Load Severity value.
TRAP-TYPE

dupsNoLongerLoadSeverity		10
INFORMATION: Returned from Load Severity condition.
TRAP-TYPE

dupsLoadOnBypass		11
SEVER: The UPS loads on bypass.
TRAP-TYPE

dupsNoLongerLoadOnBypass		12
INFORMATION: The UPS is not on bypass mode.
TRAP-TYPE

dupsUPSFault		13
SEVER: A general fault caused in the UPS.
TRAP-TYPE

dupsReturnFromUPSFault		14
INFORMATION: The UPS is returned from general fault.
TRAP-TYPE

dupsBatteryGroundFault		15
SEVER: The UPS battery ground fault.
TRAP-TYPE

dupsNoLongerBatteryFault		16
INFORMATION: The UPS recovered from battery ground fault.
TRAP-TYPE

dupsTestInProgress		17
INFORMATION: The UPS test in progress.
TRAP-TYPE

dupsBatteryTestFail		18
SEVER: The UPS test fail.
TRAP-TYPE

dupsFuseFailure		19
SEVER: The UPS fuse failed.
TRAP-TYPE

dupsFuseRecovered		20
INFORMATION: The UPS fuse recovered.
TRAP-TYPE

dupsOutputOverload		21
SEVER: The UPS overload!.
TRAP-TYPE

dupsNoLongerOverload		22
INFORMATION: Recovered from UPS overload.
TRAP-TYPE

dupsOutputOverCurrent		23
SEVER: The UPS output overcurrent.
TRAP-TYPE

dupsNoLongerOutputOverCurrent		24
INFORMATION: Recovered from UPS overcurrent.
TRAP-TYPE

dupsInverterAbnormal		25
SEVER: The UPS inverter abnormal.
TRAP-TYPE

dupsInverterRecovered		26
INFORMATION: Recovered from UPS inverter abnormal.
TRAP-TYPE

dupsRectifierAbnormal		27
SEVER: The UPS rectifier abnormal.
TRAP-TYPE

dupsRectifierRecovered		28
INFORMATION: The UPS recovered from rectifier abnormal.
TRAP-TYPE

dupsReserveAbnormal		29
SEVER: The UPS rectifier abnormal.
TRAP-TYPE

dupsReserveRecovered		30
INFORMATION: The UPS rectifier abnormal.
TRAP-TYPE

dupsLoadOnReserve		31
SEVER: The UPS load on reserve.
TRAP-TYPE

dupsNoLongerLoadOnReserve		32
INFORMATION: The UPS no longer load on reserve.
TRAP-TYPE

dupsEnvOverTemperature		33
WARNING: The environment overtemperature.
TRAP-TYPE

dupsNoLongerEnvOverTemperature		34
INFORMATION: The environment recovered from overtemperature.
TRAP-TYPE

dupsEnvOverHumidity		35
WARNING: The environment overhumidity.
TRAP-TYPE

dupsNoLongerEnvOverHumidity		36
INFORMATION: The environment recovered from overhumidity.
TRAP-TYPE

dupsEnvRelay1Alarm		37
INFORMATION: The environment relay1 is not in normal state.
TRAP-TYPE

dupsEnvRelay1Normal		38
INFORMATION: The environment relay1 is in normal state.
TRAP-TYPE

dupsEnvRelay2Alarm		39
INFORMATION: The environment relay2 is not in normal state.
TRAP-TYPE

dupsEnvRelay2Normal		40
INFORMATION: The environment relay2 is in normal state.
TRAP-TYPE

dupsEnvRelay3Alarm		41
INFORMATION: The environment relay3 is not in normal state.
TRAP-TYPE

dupsEnvRelay3Normal		42
INFORMATION: The environment relay3 is in normal state.
TRAP-TYPE

dupsEnvRelay4Alarm		43
INFORMATION: The environment relay4 is not in normal state.
TRAP-TYPE

dupsEnvRelay4Normal		44
INFORMATION: The environment relay4 is in normal state.
TRAP-TYPE

dupsSmartShutdown		45
SEVER: Smart Shutdown is initiated.
TRAP-TYPE

dupsCancelShutdown		46
INFORMATION: Cancel UPS Shutdown.
TRAP-TYPE

dupsTestCompleted		47
INFORMATION: This trap is sent upon completion of a UPS diagnostic test.
TRAP-TYPE

dupsEPOON		48
INFORMATION: This trap is sent when emergency power off is on.
TRAP-TYPE

dupsEPOOFF		49
INFORMATION: This trap is sent when UPS recover from emergency power off.
TRAP-TYPE

dupsOverTemperature		50
SEVER: This trap is sent when the UPS is over heat.
TRAP-TYPE

dupsNormalTemperature		51
INFORMATION: This trap is sent when UPS recover from over heat.
TRAP-TYPE

dupsBattReplace		52
WARNING: The battery needs to be replaced.
TRAP-TYPE

dupsReturnFromBattReplace		53
INFORMATION: The UPS recovered from battery replacement.
TRAP-TYPE

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor