DLINKSW-SWITCHPORT-MIB
File:
DLINKSW-SWITCHPORT-MIB.mib (6933 bytes)
Imported modules
Imported symbols
Defined Types
DSwPortIfEntry |
|
SEQUENCE |
|
|
|
|
dSwPortIfB1000baseTCtrl |
INTEGER |
|
|
dSwPortIfB10GbaseTCtrl |
INTEGER |
|
|
dSwPortIfMdix |
INTEGER |
|
|
dSwPortIfJumboFrameSize |
Unsigned32 |
|
|
dSwPortIfSpeedAutoDowngrade |
TruthValue |
|
Defined Values
dlinkSwSwitchPortMIB |
1.3.6.1.4.1.171.14.11 |
This MIB module defines objects for per-port configuration which
are not covered by standard MIB(s). |
MODULE-IDENTITY |
|
|
|
dSwPortIfTable |
1.3.6.1.4.1.171.14.11.1.1 |
A list of physical port interface entries. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
DSwPortIfEntry |
|
dSwPortIfEntry |
1.3.6.1.4.1.171.14.11.1.1.1 |
An entry in dSwPortIfTable contains port-specific configuration
which cannot be covered by standard MIBs (EtherLike or MAU-MIB). |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
DSwPortIfEntry |
|
|
dSwPortIfB1000baseTCtrl |
1.3.6.1.4.1.171.14.11.1.1.1.1 |
This object can be modified when port speed is configured to 1000BASE-T.
other(1) - the port is not 1000BASE-T or master/slave timing mode
is not specified.
b1000baseTMaster(2) - configure the port operate as master timing.
b1000baseTSlave(3) - configure the port operate as slave timing.
|
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), b1000baseTMaster(2), b1000baseTSlave(3) |
|
dSwPortIfB10GbaseTCtrl |
1.3.6.1.4.1.171.14.11.1.1.1.2 |
This object can be modified when port speed is configured to 10GBASE-T.
other(1) - the port is not 10GBASE-T or master/slave timing mode
is not specified.
b10GbaseTMaster(2) - configure the port operate as master timing.
b10GbaseTSlave(3) - configure the port operate as slave timing.
|
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), b10GbaseTMaster(2), b10GbaseTSlave(3) |
|
dSwPortIfMdix |
1.3.6.1.4.1.171.14.11.1.1.1.3 |
Uses the object to configure the state of Media-Dependent Interface
Crossover (MDIX) of the port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
auto(1), normal(2), cross(3) |
|
dSwPortIfJumboFrameSize |
1.3.6.1.4.1.171.14.11.1.1.1.4 |
The size of the largest packet which can be received on the
interface, specified in octets. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
dSwPortIfSpeedAutoDowngrade |
1.3.6.1.4.1.171.14.11.1.1.1.5 |
This object indicates whether automatically downgrade the advertised
speed in case a link cannot be established at the available speed.
|
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
dSwPortCompliance |
1.3.6.1.4.1.171.14.11.2.1.1 |
The compliance statement for entities which implement the
DLINKSW-SWITCHPORT-MIB. |
Status: current |
Access: read-only |
MODULE-COMPLIANCE |
|
|
|
dSwPortBasicGroup |
1.3.6.1.4.1.171.14.11.2.2.1 |
This group contains the collection of fundamental port configuration
objects which are not covered by standard MIBs. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|