DLINK-AGENT-MIB

File: DLINK-AGENT-MIB.mib (58355 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI SNMPv2-TC
RFC1213-MIB DLINK-ID-REC-MIB

Imported symbols

IpAddress NOTIFICATION-TYPE MODULE-IDENTITY
OBJECT-TYPE Integer32 TruthValue
DisplayString AgentNotifyLevel RowStatus
dlink-common-mgmt MacAddress

Defined Types

AgentMibCapabilityEntry  
SEQUENCE    
  agentMibCapabilityIndex Integer32
  agentMibCapabilityDescr DisplayString
  agentMibCapabilityVersion Integer32
  agentMibCapabilityType INTEGER

AgentPORTutilizationEntry  
SEQUENCE    
  agentPORTutilizationProtIndex INTEGER
  agentPORTutilizationTX INTEGER
  agentPORTutilizationRX INTEGER
  agentPORTutilizationUtil INTEGER

AgentDRAMutilizationEntry  
SEQUENCE    
  agentDRAMutilizationUnitID INTEGER
  agentDRAMutilizationTotalDRAM INTEGER
  agentDRAMutilizationUsedDRAM INTEGER
  agentDRAMutilization INTEGER

AgentBscSwFileEntry  
SEQUENCE    
  agentBscSwFileIndex Integer32
  agentBscSwFileDscr DisplayString
  agentBscSwFileAddr IpAddress
  agentBscSwFileTransferType INTEGER
  agentBscSwFile DisplayString
  agentBscSwFileLocateId INTEGER
  agentBscSwFileLoadType INTEGER
  agentBscSwFileCtrl INTEGER
  agentBscSwFileBIncrement TruthValue
  agentMultiImageCtrlID INTEGER

SwMultiImageInfoEntry  
SEQUENCE    
  swMultiImageInfoID INTEGER
  swMultiImageVersion DisplayString
  swMultiImageSize Integer32
  swMultiImageUpdateTime DisplayString
  swMultiImageFrom DisplayString
  swMultiImageSendUser DisplayString

AgentTrustHostEntry  
SEQUENCE    
  agentTrustHostIndex INTEGER
  agentTrustHostIPAddress IpAddress
  agentTrustHostRowStatus RowStatus
  agentTrustHostIPSubnetMask IpAddress
  agentTrustHostForSNMP INTEGER
  agentTrustHostForTELNET INTEGER
  agentTrustHostForSSH INTEGER
  agentTrustHostForHTTP INTEGER
  agentTrustHostForHTTPS INTEGER

AgentGratuitousARPEntry  
SEQUENCE    
  agentGratuitousARPInterfaceName DisplayString
  agentGratuitousARPPeriodicalSendInterval INTEGER
  agentGratuitousARPTrapState INTEGER
  agentGratuitousARPLogState INTEGER

Defined Values

agentGeneralMgmt 1.3.6.1.4.1.171.12.1
The Structure of Common Management Information for the D-Link enterprise.
MODULE-IDENTITY    

agentBasicInfo 1.3.6.1.4.1.171.12.1.1
OBJECT IDENTIFIER    

agentMgmtProtocolCapability 1.3.6.1.4.1.171.12.1.1.1
The network management protocol(s) supported by this agent.
OBJECT-TYPE    
  INTEGER other(1), snmp-ip(2), snmp-ipx(3), snmp-ip-ipx(4)  

agentMibCapabilityTable 1.3.6.1.4.1.171.12.1.1.2
A list of MIB capability entries supported by this agent.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentMibCapabilityEntry

agentMibCapabilityEntry 1.3.6.1.4.1.171.12.1.1.2.1
A MIB capability entry contains objects describing a particular MIB supported by this agent.
OBJECT-TYPE    
  AgentMibCapabilityEntry  

agentMibCapabilityIndex 1.3.6.1.4.1.171.12.1.1.2.1.1
A list of agentMibCapabilityDescr entries.
OBJECT-TYPE    
  Integer32  

agentMibCapabilityDescr 1.3.6.1.4.1.171.12.1.1.2.1.2
The name of the MIB supported by the agent.
OBJECT-TYPE    
  DisplayString Size(0..35)  

agentMibCapabilityVersion 1.3.6.1.4.1.171.12.1.1.2.1.3
The version of the MIB specified in this entry.
OBJECT-TYPE    
  Integer32  

agentMibCapabilityType 1.3.6.1.4.1.171.12.1.1.2.1.4
The type of the MIB specified in this entry.
OBJECT-TYPE    
  INTEGER other(1), standard(2), proprietary(3), experiment(4)  

agentStatusConsoleInUse 1.3.6.1.4.1.171.12.1.1.3
This indicates whether the console is currently in-use.
OBJECT-TYPE    
  INTEGER other(1), in-use(2), not-in-use(3)  

agentStatusSaveCfg 1.3.6.1.4.1.171.12.1.1.4
This indicates the status of the device configuration. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. proceeding(2) - the device configuration is being currently saved into the NV-RAM. completed(3) - all of the device configuration parameters have been saved into NV-RAM. failed(4) - The process to save device configuration has failed.
OBJECT-TYPE    
  INTEGER other(1), proceeding(2), completed(3), failed(4)  

agentStatusFileTransfer 1.3.6.1.4.1.171.12.1.1.5
The status of the firmware download control. If the value is 'other', this means the firmware has not been updated since the device started up.
OBJECT-TYPE    
  INTEGER other(1), in-process(2), invalid-file(3), violation(4), file-not-found(5), disk-full(6), complete(7), time-out(8), not-format(9), memory-full(10)  

agentCPUutilization 1.3.6.1.4.1.171.12.1.1.6
OBJECT IDENTIFIER    

agentCPUutilizationIn5sec 1.3.6.1.4.1.171.12.1.1.6.1
The unit of time is 5 seconds. The value will be between 0% (idle) and 100% (very busy).
OBJECT-TYPE    
  Integer32  

agentCPUutilizationIn1min 1.3.6.1.4.1.171.12.1.1.6.2
The unit of time is 1 minute. The value will be between 0% (idle) and 100% (very busy).
OBJECT-TYPE    
  Integer32  

agentCPUutilizationIn5min 1.3.6.1.4.1.171.12.1.1.6.3
The unit of time is 5 minutes. The value will be between 0% (idle) and 100% (very busy).
OBJECT-TYPE    
  Integer32  

agentPORTutilizationTable 1.3.6.1.4.1.171.12.1.1.7
The table specifies the port's utilization function.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentPORTutilizationEntry

agentPORTutilizationEntry 1.3.6.1.4.1.171.12.1.1.7.1
A list of information about the port's utilization function.
OBJECT-TYPE    
  AgentPORTutilizationEntry  

agentPORTutilizationProtIndex 1.3.6.1.4.1.171.12.1.1.7.1.1
This object indicates the module's port number.
OBJECT-TYPE    
  INTEGER 1..65535  

agentPORTutilizationTX 1.3.6.1.4.1.171.12.1.1.7.1.2
The real-time gauges of transmitted frames on the specific port.
OBJECT-TYPE    
  INTEGER  

agentPORTutilizationRX 1.3.6.1.4.1.171.12.1.1.7.1.3
The real-time gauges of recieved frames on the specific port.
OBJECT-TYPE    
  INTEGER  

agentPORTutilizationUtil 1.3.6.1.4.1.171.12.1.1.7.1.4
The real-time percentage of the port statistics.
OBJECT-TYPE    
  INTEGER 0..100  

agentDRAMutilizationTable 1.3.6.1.4.1.171.12.1.1.9
Information about DRAM memory.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentDRAMutilizationEntry

agentDRAMutilizationEntry 1.3.6.1.4.1.171.12.1.1.9.1
A list of information about DRAM memory.
OBJECT-TYPE    
  AgentDRAMutilizationEntry  

agentDRAMutilizationUnitID 1.3.6.1.4.1.171.12.1.1.9.1.1
Specifies the unit ID. If the ID equals zero, it means the current device.
OBJECT-TYPE    
  INTEGER  

agentDRAMutilizationTotalDRAM 1.3.6.1.4.1.171.12.1.1.9.1.2
The size of the total DRAM memory.
OBJECT-TYPE    
  INTEGER  

agentDRAMutilizationUsedDRAM 1.3.6.1.4.1.171.12.1.1.9.1.3
The size of the used DRAM memory.
OBJECT-TYPE    
  INTEGER  

agentDRAMutilization 1.3.6.1.4.1.171.12.1.1.9.1.4
The percentage of used DRAM memory of the total DRAM memory available. The value will be between 0%(idle) and 100%(very busy).
OBJECT-TYPE    
  INTEGER  

agentStatusReset 1.3.6.1.4.1.171.12.1.1.11
This indicates the status of 'agentReset'.
OBJECT-TYPE    
  INTEGER proceeding(1), completed(2), failed(3)  

agentSerialNumber 1.3.6.1.4.1.171.12.1.1.12
A text string containing the serial number of this device.
OBJECT-TYPE    
  DisplayString  

agentBasicConfig 1.3.6.1.4.1.171.12.1.2
OBJECT IDENTIFIER    

agentBscSwFileTable 1.3.6.1.4.1.171.12.1.2.1
A list of MIB basic config entries that support file update by this agent.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentBscSwFileEntry

agentBscSwFileEntry 1.3.6.1.4.1.171.12.1.2.1.1
A basic configuration entry contains objects describing a particular MIB supported by this agent.
OBJECT-TYPE    
  AgentBscSwFileEntry  

agentBscSwFileIndex 1.3.6.1.4.1.171.12.1.2.1.1.1
The table index for the file entry.
OBJECT-TYPE    
  Integer32  

agentBscSwFileDscr 1.3.6.1.4.1.171.12.1.2.1.1.2
The description for the purpose of the software file in this entry. Note: For systems which do not support change of this object, setting values to this object will cause the system to return a bad-value error message.
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscSwFileAddr 1.3.6.1.4.1.171.12.1.2.1.1.3
The IP address where the file to be downloaded is located, or the IP address where the file will be uploaded to.
OBJECT-TYPE    
  IpAddress  

agentBscSwFileTransferType 1.3.6.1.4.1.171.12.1.2.1.1.4
The channel through which the file will be downloaded or uploaded. Note: For systems which do not support all channels, setting values to the unsupported channel will cause the system to return a bad-value error message.
OBJECT-TYPE    
  INTEGER other(1), network-load(2), out-of-band-load(3)  

agentBscSwFile 1.3.6.1.4.1.171.12.1.2.1.1.5
The name of the file to be downloaded from the TFTP server, or to be uploaded to.
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscSwFileLocateId 1.3.6.1.4.1.171.12.1.2.1.1.6
This object describes the type of the file. runtime-code(1), log-file(2), cfg-file(3) Note: For a system which does not support change of this object, setting a value to this object will cause the system to return a bad-value error message.
OBJECT-TYPE    
  INTEGER 1..16  

agentBscSwFileLoadType 1.3.6.1.4.1.171.12.1.2.1.1.7
This object allows the user to select the download or upload function for the file. Note: For a system which does not support change of this object, setting a value to this object will cause the system to return a bad-value error message.
OBJECT-TYPE    
  INTEGER other(1), upload(2), download(3)  

agentBscSwFileCtrl 1.3.6.1.4.1.171.12.1.2.1.1.8
This object allows the user to download runtime software. The setting will take effect when the system restarts. See Note (1) below Note: For systems which do not support change of this object to some value, setting these values causes the system to return bad-value error messages. start - start to action. delete(4) - delete the firmware by indicated firmware ID. config-as-bootup-fw(5) - configured as bootup firmware by indicated firmware(ID).
OBJECT-TYPE    
  INTEGER other(1), inactive(2), start(3), delete(4), config-as-bootup-fw(5)  

agentBscSwFileBIncrement 1.3.6.1.4.1.171.12.1.2.1.1.9
The object indicates whether the previous configuration will be valid or not after downloading the configuration file. True: keep valid False: erase.
OBJECT-TYPE    
  TruthValue  

agentMultiImageCtrlID 1.3.6.1.4.1.171.12.1.2.1.1.10
The section ID of the firmware image.
OBJECT-TYPE    
  INTEGER  

agentFileTransfer 1.3.6.1.4.1.171.12.1.2.2
This object will execute the download or upload action. If start(2), it will begin to download/upload, but no reset follows. If start-and-reset(3), then the reset will activate after download or upload. No action if (4). Note: Because these functions will be limited by the system support, some of the selected items will be invalid. When the user selects one of the items, it will respond with bad-value status.
OBJECT-TYPE    
  INTEGER other(1), start(2), start-and-reset(3), noaction(4)  

agentSystemReset 1.3.6.1.4.1.171.12.1.2.3
This object indicates the agent system reset state. Setting this object to no-reset(4) has no effect. Setting this object to cold-start(2) or warm-start(3) will reset the agent. The agent always returns no-reset(4) when this object is read.
OBJECT-TYPE    
  INTEGER other(1), cold-start(2), warm-start(3), no-reset(4)  

agentRs232PortConfig 1.3.6.1.4.1.171.12.1.2.4
This object indicates the RS-232C mode when the device has restarted.
OBJECT-TYPE    
  INTEGER other(1), console(2), out-of-band(3), notAvail(4)  

agentOutOfBandBaudRateConfig 1.3.6.1.4.1.171.12.1.2.5
This object allows the user to the specify out-of-band baud rate. It will take effect when the system is restarted. Note: Because these functions will be limited by the system support, some of the selected items will be invalid. When the user selects one of the items, it will respond with a bad-value status.
OBJECT-TYPE    
  INTEGER other(1), baudRate-2400(2), baudRate-9600(3), baudRate-19200(4), baudRate-38400(5), baudRate-115200(6)  

agentSaveCfg 1.3.6.1.4.1.171.12.1.2.6
As the object is set to 'set(3)', the current device configuration will be saved into to NV-RAM.
OBJECT-TYPE    
  INTEGER other(1), idle(2), set(3)  

swMultiImageInfoTable 1.3.6.1.4.1.171.12.1.2.7
Tok_String
OBJECT-TYPE    
  SEQUENCE OF  
    SwMultiImageInfoEntry

swMultiImageInfoEntry 1.3.6.1.4.1.171.12.1.2.7.1
A list of information about multiple image management.
OBJECT-TYPE    
  SwMultiImageInfoEntry  

swMultiImageInfoID 1.3.6.1.4.1.171.12.1.2.7.1.1
The section ID of the firmware image.
OBJECT-TYPE    
  INTEGER  

swMultiImageVersion 1.3.6.1.4.1.171.12.1.2.7.1.2
The record of the downloaded firmware version.
OBJECT-TYPE    
  DisplayString Size(0..32)  

swMultiImageSize 1.3.6.1.4.1.171.12.1.2.7.1.3
The record of the downloaded firmware size.
OBJECT-TYPE    
  Integer32  

swMultiImageUpdateTime 1.3.6.1.4.1.171.12.1.2.7.1.4
The record of the firmware updated time.
OBJECT-TYPE    
  DisplayString Size(0..32)  

swMultiImageFrom 1.3.6.1.4.1.171.12.1.2.7.1.5
The record of the IP address of the TFTP server.
OBJECT-TYPE    
  DisplayString Size(0..32)  

swMultiImageSendUser 1.3.6.1.4.1.171.12.1.2.7.1.6
The record of the user who downloaded the firmware.
OBJECT-TYPE    
  DisplayString Size(0..32)  

agentTrustHostMgmt 1.3.6.1.4.1.171.12.1.2.10
OBJECT IDENTIFIER    

agentTrustHostTable 1.3.6.1.4.1.171.12.1.2.10.1
This table contains trusted host information.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentTrustHostEntry

agentTrustHostEntry 1.3.6.1.4.1.171.12.1.2.10.1.1
A list of information about trusted host.
OBJECT-TYPE    
  AgentTrustHostEntry  

agentTrustHostIndex 1.3.6.1.4.1.171.12.1.2.10.1.1.1
The index of the trusted host entry.
OBJECT-TYPE    
  INTEGER 1..10  

agentTrustHostIPAddress 1.3.6.1.4.1.171.12.1.2.10.1.1.2
Specifies the IP address of the trusted host.
OBJECT-TYPE    
  IpAddress  

agentTrustHostRowStatus 1.3.6.1.4.1.171.12.1.2.10.1.1.3
Indicates the status of this entry. When creating a trusted host entry, the IP address should be set, too.
OBJECT-TYPE    
  RowStatus  

agentTrustHostIPSubnetMask 1.3.6.1.4.1.171.12.1.2.10.1.1.4
Specifies the IP subnet mask of the trusted host.
OBJECT-TYPE    
  IpAddress  

agentTrustHostForSNMP 1.3.6.1.4.1.171.12.1.2.10.1.1.5
Specifies the trusted host for SNMP.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrustHostForTELNET 1.3.6.1.4.1.171.12.1.2.10.1.1.6
Specifies the trusted host for TELNET.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrustHostForSSH 1.3.6.1.4.1.171.12.1.2.10.1.1.7
Specifies the trusted host for SSH.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrustHostForHTTP 1.3.6.1.4.1.171.12.1.2.10.1.1.8
Specifies the trusted host for HTTP.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrustHostForHTTPS 1.3.6.1.4.1.171.12.1.2.10.1.1.9
Specifies the trusted host for HTTPS.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentFDBMgmt 1.3.6.1.4.1.171.12.1.2.11
OBJECT IDENTIFIER    

agentFDBClearAllState 1.3.6.1.4.1.171.12.1.2.11.1
Used to clear all FDB entries.
OBJECT-TYPE    
  INTEGER other(1), start(2)  

agentARPMgmt 1.3.6.1.4.1.171.12.1.2.12
OBJECT IDENTIFIER    

agentARPClearAllState 1.3.6.1.4.1.171.12.1.2.12.1
Used to clear all ARP entries.
OBJECT-TYPE    
  INTEGER other(1), start(2)  

agentGratuitousARPMgmt 1.3.6.1.4.1.171.12.1.2.12.2
OBJECT IDENTIFIER    

agentGratuitousARPSendIpifStatusUpState 1.3.6.1.4.1.171.12.1.2.12.2.1
It is used to enable/disable sending of gratuitous ARP request packets while IPIF interface come up. This is used to automatically announce the interface's IP address to other nodes. By default, the state is enabled, and only one ARP packet will be broadcast.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentGratuitousARPSendDupIpDetectedState 1.3.6.1.4.1.171.12.1.2.12.2.2
It is used to enable/disable sending of gratuitous ARP request packets while a duplicate IP is detected. By default, the state is enabled. The duplicate IP detected means that the system received a ARP request packet that is sent by an IP address that matches the system's own IP address. In this case, the system knows that somebody out there is using an IP address that is in conflict with the system. In order to reclaim the correct host of this IP address, the system can send out the gratuitous ARP request packet for this duplicate IP address.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentGratuitousARPLearningState 1.3.6.1.4.1.171.12.1.2.12.2.3
It is used to enable/disable learning of an ARP entry in the ARP cache based on the received gratuitous ARP packet. If the switch receives a gratuitous ARP request/reply packet and the sender's IP address is in its ARP table, it should update the ARP entry. By default, the state is disabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentGratuitousARPTable 1.3.6.1.4.1.171.12.1.2.12.2.4
Gratuitous ARP Table Information.
OBJECT-TYPE    
  SEQUENCE OF  
    AgentGratuitousARPEntry

agentGratuitousARPEntry 1.3.6.1.4.1.171.12.1.2.12.2.4.1
A list of information from the Gratuitous ARP Table.
OBJECT-TYPE    
  AgentGratuitousARPEntry  

agentGratuitousARPInterfaceName 1.3.6.1.4.1.171.12.1.2.12.2.4.1.1
The name of the IP interface.
OBJECT-TYPE    
  DisplayString  

agentGratuitousARPPeriodicalSendInterval 1.3.6.1.4.1.171.12.1.2.12.2.4.1.2
It is used to configure the interval for the periodic sending of gratuitous ARP request packets. 0 means not send gratuitous ARP periodically.
OBJECT-TYPE    
  INTEGER 0..65535  

agentGratuitousARPTrapState 1.3.6.1.4.1.171.12.1.2.12.2.4.1.3
It indicates the state of the gratuitous ARP trap. The switch can trap the IP conflict event to inform the administrator. By default, the trap is disabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentGratuitousARPLogState 1.3.6.1.4.1.171.12.1.2.12.2.4.1.4
It indicates the state of the gratuitous Log trap. The switch can log the IP conflict event to inform the administrator. By default, the event log is enabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentReboot 1.3.6.1.4.1.171.12.1.2.19
Used to restart the switch.
OBJECT-TYPE    
  INTEGER none(1), start(2)  

agentReset 1.3.6.1.4.1.171.12.1.2.20
Used to reset all switch parameters. none(1) : No action. This is the default value of this object. config(2): All parameters are reset to default settings, but the device will neither save nor reboot. system(3): All parameters are reset to default settings. The switch will then do a factory reset, save, and reboot. reset(4) : All parameters will be reset to default settings except IP address, user account, and history log, but the device will neither save nor reboot. system-exlude-vlan(5) : All parameters are reset to default settings except VLAN. The switch will then save its settings and reboot. system-_exlude-ip(6) : All parameters are reset to default settings except IP address. The switch will then save its settings and reboot. system-exlude-vlan-ip(7): All parameters are reset to default settings except VLAN and IP address. The switch will then save its settings and reboot.
OBJECT-TYPE    
  INTEGER none(1), config(2), system(3), reset(4), system-exclude-vlan(5), system-exclude-ip(6), system-exclude-vlan-ip(7)  

agentSnmpTrapState 1.3.6.1.4.1.171.12.1.2.22
This object indicates the state of snmp trap is enabled or disabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrustHostDelAllState 1.3.6.1.4.1.171.12.1.2.10.2
Used to delete all trusted host entries.
OBJECT-TYPE    
  INTEGER none(1), start(2)  

agentIpProtoConfig 1.3.6.1.4.1.171.12.1.3
OBJECT IDENTIFIER    

agentIpNumOfIf 1.3.6.1.4.1.171.12.1.3.1
The total number of IP interfaces supported by this agent.
OBJECT-TYPE    
  Integer32  

agentIpTftpServerAddr 1.3.6.1.4.1.171.12.1.3.2
The IP Address of the TFTP server.
OBJECT-TYPE    
  IpAddress  

agentIpGetIpFrom 1.3.6.1.4.1.171.12.1.3.3
This object indicates whether the agent get its system IP address from BOOTP/DHCP server at start up.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), bootp(3), dhcp(4)  

agentIpAutoconfig 1.3.6.1.4.1.171.12.1.3.4
Tok_String
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentNotify 1.3.6.1.4.1.171.12.1.4
OBJECT IDENTIFIER    

agentNotifMgmt 1.3.6.1.4.1.171.12.1.4.1
OBJECT IDENTIFIER    

agentNotifFirmware 1.3.6.1.4.1.171.12.1.4.2
OBJECT IDENTIFIER    

agentNotifyPrefix 1.3.6.1.4.1.171.12.1.4.2.0
OBJECT IDENTIFIER    

systemTrapsSeverity 1.3.6.1.4.1.171.12.1.4.1.1
Indicates the level of system severity control. The system has a severity level control and each trap should be associated with a severity control. When a trap event occurs and its severity is higher than the system severity control level, the trap works as defined. If the event severity is lower than the system severity control level, the event is ignored as if it did not occur.
OBJECT-TYPE    
  AgentNotifyLevel  

systemLogsSeverity 1.3.6.1.4.1.171.12.1.4.1.2
Indicates the level of system severity control. The system has a severity level control and each log should be associated with a severity control. When a log event occurs and its severity is higher than the system severity control level, the log works as defined. If the event severity is lower than the system severity control level, the event is ignored as if it did not occur.
OBJECT-TYPE    
  AgentNotifyLevel  

agentGratuitousARPTrap 1.3.6.1.4.1.171.12.1.4.2.0.5
The trap is sent when there is an IP address conflict.
NOTIFICATION-TYPE    

notificationBidings 1.3.6.1.4.1.171.12.1.4.2.1
OBJECT IDENTIFIER    

agentGratuitousARPIpAddr 1.3.6.1.4.1.171.12.1.4.2.1.3
Duplicate IP address with the switch.
OBJECT-TYPE    
  IpAddress  

agentGratuitousARPMacAddr 1.3.6.1.4.1.171.12.1.4.2.1.4
The MAC address of the device which has the duplicate IP address.
OBJECT-TYPE    
  MacAddress  

agentGratuitousARPPortNumber 1.3.6.1.4.1.171.12.1.4.2.1.5
It indicates the portNum with a string, For example, if the device is in standalone mode, and the port number is 23, the string should be 23. If the device is in stack mode, and the unit ID is 2, and the port number is 3, the string should be 2:3.
OBJECT-TYPE    
  DisplayString