DKT-FE-MIB
File:
DKT-FE-MIB.mib (43923 bytes)
Imported modules
Imported symbols
Defined Values
feMIB |
1.3.6.1.4.1.27304.12 |
DKT Fast Ethernet MIB. |
MODULE-IDENTITY |
|
|
|
feATU |
1.3.6.1.4.1.27304.12.1.1 |
Dumps the Address Translation Unit (ATU) Switch table in semi colon format |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..20480) |
|
feUnicastDelete |
1.3.6.1.4.1.27304.12.1.2 |
Removes a unicast MAC address from the Address Translation Unit (ATU) Switch table. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feMulticastDelete |
1.3.6.1.4.1.27304.12.1.3 |
Removes a multicast IP address from the Address Translation Unit (ATU) Switch table. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
feIGMPSnooping |
1.3.6.1.4.1.27304.12.1.4 |
Starts/stops IGMP snooping, input parameter 0 = stops IGMP snooping, 1 = starts IGMP snooping. Per Default IGMP snooping is enabled, but has to be configured per port |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feVTU |
1.3.6.1.4.1.27304.12.1.5 |
Dumps the VLAN Table Unit (VTU) Switch table in semi colon format |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..9600) |
|
feVLANCreate |
1.3.6.1.4.1.27304.12.1.6 |
Creates a VLAN, input parameters are: VID:WAN:LAN1:LAN2:LAN3:LAN4:CPU:NRL-ENABLE |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feVLANDelete |
1.3.6.1.4.1.27304.12.1.7 |
Deletes a VLAN, input parameter is VLAN VID: 0 - 4095 |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..4095 |
|
feClearVTU |
1.3.6.1.4.1.27304.12.1.8 |
Clears the VLAN Table Unit (VTU) Switch table, input parameter 1 = clear VTU table |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1 |
|
feDumpPIRLBuckets |
1.3.6.1.4.1.27304.12.1.9 |
Dumps a list of the active buckets. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
feDisablePIRLBucket |
1.3.6.1.4.1.27304.12.1.10 |
Disables an already defined Port Ingress Rate Limitation (PIRL) bucket, input parameter bucket 0 - 11. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..11 |
|
feVLANProviderMode |
1.3.6.1.4.1.27304.12.1.11 |
Enable/disable VLAN provider mode, input parameter 0 = disable VLAN provider mode, 1 = enable VLAN provider mode. Per Default VLAN provider mode is disabled. NOTE: Provider VLAN ID should be setup in port default VID for the originating port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
fePorts |
1.3.6.1.4.1.27304.12.2 |
OBJECT IDENTIFIER |
|
|
|
feCPUPort |
1.3.6.1.4.1.27304.12.2.1 |
OBJECT IDENTIFIER |
|
|
|
feCPUPortAutoNegotiation |
1.3.6.1.4.1.27304.12.2.1.1 |
Enables/disables auto negotiation on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..10 |
|
feCPUPortSpeedMode |
1.3.6.1.4.1.27304.12.2.1.2 |
Sets/gets the speed and duplex mode on the port. Input parameters are: 100FD|100HD|10FD|10HD|AUTO|FD|HD |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
feCPUPortLinkStatus |
1.3.6.1.4.1.27304.12.2.1.3 |
Gets the Link status for the port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feCPUPortFlowControl |
1.3.6.1.4.1.27304.12.2.1.4 |
Enables/disables flow control on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feCPUPortIEEEQoSPriority |
1.3.6.1.4.1.27304.12.2.1.5 |
Enables prioritized frames based on there IEEE priority tags. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feCPUPortIPQoSPriority |
1.3.6.1.4.1.27304.12.2.1.6 |
Enables prioritized frames based on their IP4/IP6 priority fields. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feCPUPortFramePriorityOverwrite |
1.3.6.1.4.1.27304.12.2.1.7 |
Source Address(SA) or Destination Address(DA) Frame Priority Override on an ATU match. XX_FRAME_PRIO_OVERRIDE=0..1. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feCPUPortQueuePriorityOverwrite |
1.3.6.1.4.1.27304.12.2.1.8 |
Source Address(SA) or Destination Address(SA) Queue Priority Override on an ATU match. XX_QUEUE_PRIO_OVERRIDE=0..1. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feCPUPortQueuePriority |
1.3.6.1.4.1.27304.12.2.1.9 |
Queue priority, input parameters: PRIO:ENABLE PRIO: 0 - 7 ENABLE: 0 - 1 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feCPUPortQoSPortMapRule |
1.3.6.1.4.1.27304.12.2.1.10 |
Forces queue priority for a port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feCPUPortVIDNRLEnable |
1.3.6.1.4.1.27304.12.2.1.11 |
Enables/disables per port the Non rate limit for VLANs with the NRL bit enabled. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feCPUPortMap2PIRL |
1.3.6.1.4.1.27304.12.2.1.12 |
Adds/maps the port to a Port Ingress Rate Limitation (PIRL) bucket. Input parameter is PIRL bucket no 0 - 11. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..11 |
|
feCPUPortDeletePortMap2PIRL |
1.3.6.1.4.1.27304.12.2.1.13 |
Deletes the port from a Port Ingress Rate Limitation (PIRL) bucket. Input parameter is PIRL bucket no 0 - 11. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..11 |
|
feCPUPortEgressRateLimitation |
1.3.6.1.4.1.27304.12.2.1.14 |
Sets the egress limitation rate for the port. Input parameter is value in kbps |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
feCPUPortIngressRateLimitation |
1.3.6.1.4.1.27304.12.2.1.15 |
Sets a Port Input Rate Limit(PIRL) bucket. Input parameters are: bucket:rate:layer:(DROP|FC) |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feCPUPortDefaultVLAN |
1.3.6.1.4.1.27304.12.2.1.16 |
Sets the default VLAN ID(VID) for the port. Input parameter is 0 - 4095 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
feCPUPortForceDefaultVID |
1.3.6.1.4.1.27304.12.2.1.17 |
Forces the tagging of VID on all frames on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feCPUPortVLANPortMode |
1.3.6.1.4.1.27304.12.2.1.18 |
Sets the 802.1Q mode for the ingress port.
Mode either 0=disable,
1=fallback,
2=check,
3=secure |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..3 |
|
feCPUPortBlockAllUnknown |
1.3.6.1.4.1.27304.12.2.1.19 |
This will make sure that all frames received on the port are blocked, unless they are tagged with the correct VID. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feCPUPortIGMPSnooping |
1.3.6.1.4.1.27304.12.2.1.20 |
Enables/disables IGMP snooping. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feCPUPortAddUnicast |
1.3.6.1.4.1.27304.12.2.1.21 |
Adds the unicast mac address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aa:bb:cc:dd:ee:ff |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feCPUPortAddMulticast |
1.3.6.1.4.1.27304.12.2.1.22 |
Adds the IP multicast address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aaa.bbb.ccc.ddd |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
feWANPort |
1.3.6.1.4.1.27304.12.2.2 |
OBJECT IDENTIFIER |
|
|
|
feWANPortAutoNegotiation |
1.3.6.1.4.1.27304.12.2.2.1 |
Enables/disables auto negotiation on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..10 |
|
feWANPortSpeedMode |
1.3.6.1.4.1.27304.12.2.2.2 |
Sets/gets the speed and duplex mode on the port. Valid values are (100FD|100HD|10FD|10HD|AUTO|FD|HD) |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
feWANPortLinkStatus |
1.3.6.1.4.1.27304.12.2.2.3 |
Gets the Link status for the port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feWANPortFlowControl |
1.3.6.1.4.1.27304.12.2.2.4 |
Enables/disables flow control on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feWANPortIEEEQoSPriority |
1.3.6.1.4.1.27304.12.2.2.5 |
Enables prioritized frames based on there IEEE priority tags. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feWANPortIPQoSPriority |
1.3.6.1.4.1.27304.12.2.2.6 |
Enables prioritized frames based on their IP4/IP6 priority fields. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feWANPortFramePriorityOverwrite |
1.3.6.1.4.1.27304.12.2.2.7 |
Source Address(SA) or Destination Address(DA) Frame Priority Override on an ATU match. XX_FRAME_PRIO_OVERRIDE=0..1. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feWANPortQueuePriorityOverwrite |
1.3.6.1.4.1.27304.12.2.2.8 |
Source Address(SA) or Destination Address(SA) Queue Priority Override on an ATU match. XX_QUEUE_PRIO_OVERRIDE=0..1. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feWANPortQueuePriority |
1.3.6.1.4.1.27304.12.2.2.9 |
Queue priority, input parameters: PRIO:ENABLE PRIO: 0 - 7 ENABLE: 0 - 1 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feWANPortQoSPortMapRule |
1.3.6.1.4.1.27304.12.2.2.10 |
Forces queue priority for a port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feWANPortVIDNRLEnable |
1.3.6.1.4.1.27304.12.2.2.11 |
Enables/disables per port the Non rate limit for VLANs with the NRL bit enabled. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feWANPortMap2PIRL |
1.3.6.1.4.1.27304.12.2.2.12 |
Adds/maps the port to a Port Ingress Rate Limitation (PIRL) bucket. Input parameter is PIRL bucket no 0 - 11. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..11 |
|
feWANPortDeletePortMap2PIRL |
1.3.6.1.4.1.27304.12.2.2.13 |
Deletes the port from a Port Ingress Rate Limitation (PIRL) bucket. Input parameter is PIRL bucket no 0 - 11. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..11 |
|
feWANPortEgressRateLimitation |
1.3.6.1.4.1.27304.12.2.2.14 |
Sets the egress limitation rate for the port. Input parameter is value in kbps |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
feWANPortIngressRateLimitation |
1.3.6.1.4.1.27304.12.2.2.15 |
Sets a Port Input Rate Limit(PIRL) bucket. Input parameters are: bucket:rate:layer:(DROP|FC) |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feWANPortDefaultVLAN |
1.3.6.1.4.1.27304.12.2.2.16 |
Sets the default VLAN ID(VID) for the port. Input parameter is 0 - 4095 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
feWANPortForceDefaultVID |
1.3.6.1.4.1.27304.12.2.2.17 |
Forces the tagging of VID on all frames on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feWANPortVLANPortMode |
1.3.6.1.4.1.27304.12.2.2.18 |
Sets the 802.1Q mode for the ingress port.
Mode either 0=disable,
1=fallback,
2=check,
3=secure |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..3 |
|
feWANPortBlockAllUnknown |
1.3.6.1.4.1.27304.12.2.2.19 |
This will make sure that all frames received on the port are blocked, unless they are tagged with the correct VID. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feWANPortIGMPSnooping |
1.3.6.1.4.1.27304.12.2.2.20 |
Enables/disables IGMP snooping. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feWANPortAddUnicast |
1.3.6.1.4.1.27304.12.2.2.21 |
Adds the unicast mac address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aa:bb:cc:dd:ee:ff |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feWANPortAddMulticast |
1.3.6.1.4.1.27304.12.2.2.22 |
Adds the IP multicast address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aaa.bbb.ccc.ddd |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
feWANPortArpMirroring |
1.3.6.1.4.1.27304.12.2.2.23 |
Mirror ARP packets seen on the port to the CPU port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN1Port |
1.3.6.1.4.1.27304.12.2.3 |
OBJECT IDENTIFIER |
|
|
|
feLAN1PortAutoNegotiation |
1.3.6.1.4.1.27304.12.2.3.1 |
Enables/disables auto negotiation on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..10 |
|
feLAN1PortSpeedMode |
1.3.6.1.4.1.27304.12.2.3.2 |
Sets/gets the speed and duplex mode on the port. Valid values are (100FD|100HD|10FD|10HD|AUTO|FD|HD) |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
feLAN1PortLinkStatus |
1.3.6.1.4.1.27304.12.2.3.3 |
Gets the Link status for the port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN1PortFlowControl |
1.3.6.1.4.1.27304.12.2.3.4 |
Enables/disables flow control on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN1PortIEEEQoSPriority |
1.3.6.1.4.1.27304.12.2.3.5 |
Enables prioritized frames based on there IEEE priority tags. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN1PortIPQoSPriority |
1.3.6.1.4.1.27304.12.2.3.6 |
Enables prioritized frames based on their IP4/IP6 priority fields. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN1PortFramePriorityOverwrite |
1.3.6.1.4.1.27304.12.2.3.7 |
Source Address(SA) or Destination Address(DA) Frame Priority Override on an ATU match. XX_FRAME_PRIO_OVERRIDE=0..1. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN1PortQueuePriorityOverwrite |
1.3.6.1.4.1.27304.12.2.3.8 |
Source Address(SA) or Destination Address(SA) Queue Priority Override on an ATU match. XX_QUEUE_PRIO_OVERRIDE=0..1. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN1PortQueuePriority |
1.3.6.1.4.1.27304.12.2.3.9 |
Queue priority, input parameters: PRIO:ENABLE PRIO: 0 - 7 ENABLE: 0 - 1 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN1PortQoSPortMapRule |
1.3.6.1.4.1.27304.12.2.3.10 |
Forces queue priority for a port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN1PortVIDNRLEnable |
1.3.6.1.4.1.27304.12.2.3.11 |
Enables/disables per port the Non rate limit for VLANs with the NRL bit enabled. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN1PortMap2PIRL |
1.3.6.1.4.1.27304.12.2.3.12 |
Adds/maps the port to a Port Ingress Rate Limitation (PIRL) bucket. Input parameter is PIRL bucket no 0 - 11. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..11 |
|
feLAN1PortDeletePortMap2PIRL |
1.3.6.1.4.1.27304.12.2.3.13 |
Deletes the port from a Port Ingress Rate Limitation (PIRL) bucket. Input parameter is PIRL bucket no 0 - 11. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..11 |
|
feLAN1PortIngressRateLimitation |
1.3.6.1.4.1.27304.12.2.3.15 |
Sets a Port Input Rate Limit(PIRL) bucket. Input parameters are: bucket:rate:layer:(DROP|FC) |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN1PortDefaultVLAN |
1.3.6.1.4.1.27304.12.2.3.16 |
Sets the default VLAN ID(VID) for the port. Input parameter is 0 - 4095 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
feLAN1PortForceDefaultVID |
1.3.6.1.4.1.27304.12.2.3.17 |
Forces the tagging of VID on all frames on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN1PortVLANPortMode |
1.3.6.1.4.1.27304.12.2.3.18 |
Sets the 802.1Q mode for the ingress port.
Mode either 0=disable,
1=fallback,
2=check,
3=secure |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..3 |
|
feLAN1PortBlockAllUnknown |
1.3.6.1.4.1.27304.12.2.3.19 |
This will make sure that all frames received on the port are blocked, unless they are tagged with the correct VID. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN1PortIGMPSnooping |
1.3.6.1.4.1.27304.12.2.3.20 |
Enables/disables IGMP snooping. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN1PortAddUnicast |
1.3.6.1.4.1.27304.12.2.3.21 |
Adds the unicast mac address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aa:bb:cc:dd:ee:ff |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN1PortAddMulticast |
1.3.6.1.4.1.27304.12.2.3.22 |
Adds the IP multicast address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aaa.bbb.ccc.ddd |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
feLAN1PortArpMirroring |
1.3.6.1.4.1.27304.12.2.3.23 |
Mirror ARP packets seen on the port to the CPU port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN2Port |
1.3.6.1.4.1.27304.12.2.4 |
OBJECT IDENTIFIER |
|
|
|
feLAN2PortAutoNegotiation |
1.3.6.1.4.1.27304.12.2.4.1 |
Enables/disables auto negotiation on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..10 |
|
feLAN2PortSpeedMode |
1.3.6.1.4.1.27304.12.2.4.2 |
Sets/gets the speed and duplex mode on the port. Valid values are (100FD|100HD|10FD|10HD|AUTO|FD|HD) |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
feLAN2PortLinkStatus |
1.3.6.1.4.1.27304.12.2.4.3 |
Gets the Link status for the port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN2PortFlowControl |
1.3.6.1.4.1.27304.12.2.4.4 |
Enables/disables flow control on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN2PortIEEEQoSPriority |
1.3.6.1.4.1.27304.12.2.4.5 |
Enables prioritized frames based on there IEEE priority tags. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN2PortIPQoSPriority |
1.3.6.1.4.1.27304.12.2.4.6 |
Enables prioritized frames based on their IP4/IP6 priority fields. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN2PortFramePriorityOverwrite |
1.3.6.1.4.1.27304.12.2.4.7 |
Source Address(SA) or Destination Address(DA) Frame Priority Override on an ATU match. XX_FRAME_PRIO_OVERRIDE=0..1. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN2PortQueuePriorityOverwrite |
1.3.6.1.4.1.27304.12.2.4.8 |
Source Address(SA) or Destination Address(SA) Queue Priority Override on an ATU match. XX_QUEUE_PRIO_OVERRIDE=0..1. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN2PortQueuePriority |
1.3.6.1.4.1.27304.12.2.4.9 |
Queue priority, input parameters: PRIO:ENABLE PRIO: 0 - 7 ENABLE: 0 - 1 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN2PortQoSPortMapRule |
1.3.6.1.4.1.27304.12.2.4.10 |
Forces queue priority for a port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN2PortVIDNRLEnable |
1.3.6.1.4.1.27304.12.2.4.11 |
Enables/disables per port the Non rate limit for VLANs with the NRL bit enabled. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN2PortMap2PIRL |
1.3.6.1.4.1.27304.12.2.4.12 |
Adds/maps the port to a Port Ingress Rate Limitation (PIRL) bucket. Input parameter is PIRL bucket no 0 - 11. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..11 |
|
feLAN2PortDeletePortMap2PIRL |
1.3.6.1.4.1.27304.12.2.4.13 |
Deletes the port from a Port Ingress Rate Limitation (PIRL) bucket. Input parameter is PIRL bucket no 0 - 11. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..11 |
|
feLAN2PortIngressRateLimitation |
1.3.6.1.4.1.27304.12.2.4.15 |
Sets a Port Input Rate Limit(PIRL) bucket. Input parameters are: bucket:rate:layer:(DROP|FC) |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN2PortDefaultVLAN |
1.3.6.1.4.1.27304.12.2.4.16 |
Sets the default VLAN ID(VID) for the port. Input parameter is 0 - 4095 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
feLAN2PortForceDefaultVID |
1.3.6.1.4.1.27304.12.2.4.17 |
Forces the tagging of VID on all frames on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN2PortVLANPortMode |
1.3.6.1.4.1.27304.12.2.4.18 |
Sets the 802.1Q mode for the ingress port.
Mode either 0=disable,
1=fallback,
2=check,
3=secure |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..3 |
|
feLAN2PortBlockAllUnknown |
1.3.6.1.4.1.27304.12.2.4.19 |
This will make sure that all frames received on the port are blocked, unless they are tagged with the correct VID. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN2PortIGMPSnooping |
1.3.6.1.4.1.27304.12.2.4.20 |
Enables/disables IGMP snooping. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN2PortAddUnicast |
1.3.6.1.4.1.27304.12.2.4.21 |
Adds the unicast mac address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aa:bb:cc:dd:ee:ff |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN2PortAddMulticast |
1.3.6.1.4.1.27304.12.2.4.22 |
Adds the IP multicast address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aaa.bbb.ccc.ddd |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
feLAN2PortArpMirroring |
1.3.6.1.4.1.27304.12.2.4.23 |
Mirror ARP packets seen on the port to the CPU port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN3Port |
1.3.6.1.4.1.27304.12.2.5 |
OBJECT IDENTIFIER |
|
|
|
feLAN3PortAutoNegotiation |
1.3.6.1.4.1.27304.12.2.5.1 |
Enables/disables auto negotiation on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..10 |
|
feLAN3PortSpeedMode |
1.3.6.1.4.1.27304.12.2.5.2 |
Sets/gets the speed and duplex mode on the port. Valid values are (100FD|100HD|10FD|10HD|AUTO|FD|HD) |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
feLAN3PortLinkStatus |
1.3.6.1.4.1.27304.12.2.5.3 |
Gets the Link status for the port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN3PortFlowControl |
1.3.6.1.4.1.27304.12.2.5.4 |
Enables/disables flow control on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN3PortIEEEQoSPriority |
1.3.6.1.4.1.27304.12.2.5.5 |
Enables prioritized frames based on there IEEE priority tags. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN3PortIPQoSPriority |
1.3.6.1.4.1.27304.12.2.5.6 |
Enables prioritized frames based on their IP4/IP6 priority fields. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN3PortFramePriorityOverwrite |
1.3.6.1.4.1.27304.12.2.5.7 |
Source Address(SA) or Destination Address(DA) Frame Priority Override on an ATU match. XX_FRAME_PRIO_OVERRIDE=0..1. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN3PortQueuePriorityOverwrite |
1.3.6.1.4.1.27304.12.2.5.8 |
Source Address(SA) or Destination Address(SA) Queue Priority Override on an ATU match. XX_QUEUE_PRIO_OVERRIDE=0..1. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN3PortQueuePriority |
1.3.6.1.4.1.27304.12.2.5.9 |
Queue priority, input parameters: PRIO:ENABLE PRIO: 0 - 7 ENABLE: 0 - 1 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN3PortQoSPortMapRule |
1.3.6.1.4.1.27304.12.2.5.10 |
Forces queue priority for a port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN3PortVIDNRLEnable |
1.3.6.1.4.1.27304.12.2.5.11 |
Enables/disables per port the Non rate limit for VLANs with the NRL bit enabled. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN3PortMap2PIRL |
1.3.6.1.4.1.27304.12.2.5.12 |
Adds/maps the port to a Port Ingress Rate Limitation (PIRL) bucket. Input parameter is PIRL bucket no 0 - 11. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..11 |
|
feLAN3PortDeletePortMap2PIRL |
1.3.6.1.4.1.27304.12.2.5.13 |
Deletes the port from a Port Ingress Rate Limitation (PIRL) bucket. Input parameter is PIRL bucket no 0 - 11. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..11 |
|
feLAN3PortIngressRateLimitation |
1.3.6.1.4.1.27304.12.2.5.15 |
Sets a Port Input Rate Limit(PIRL) bucket. Input parameters are: bucket:rate:layer:(DROP|FC) |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN3PortDefaultVLAN |
1.3.6.1.4.1.27304.12.2.5.16 |
Sets the default VLAN ID(VID) for the port. Input parameter is 0 - 4095 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
feLAN3PortForceDefaultVID |
1.3.6.1.4.1.27304.12.2.5.17 |
Forces the tagging of VID on all frames on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN3PortVLANPortMode |
1.3.6.1.4.1.27304.12.2.5.18 |
Sets the 802.1Q mode for the ingress port.
Mode either 0=disable,
1=fallback,
2=check,
3=secure |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..3 |
|
feLAN3PortBlockAllUnknown |
1.3.6.1.4.1.27304.12.2.5.19 |
This will make sure that all frames received on the port are blocked, unless they are tagged with the correct VID. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN3PortIGMPSnooping |
1.3.6.1.4.1.27304.12.2.5.20 |
Enables/disables IGMP snooping. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN3PortAddUnicast |
1.3.6.1.4.1.27304.12.2.5.21 |
Adds the unicast mac address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aa:bb:cc:dd:ee:ff |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN3PortAddMulticast |
1.3.6.1.4.1.27304.12.2.5.22 |
Adds the IP multicast address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aaa.bbb.ccc.ddd |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
feLAN3PortArpMirroring |
1.3.6.1.4.1.27304.12.2.5.23 |
Mirror ARP packets seen on the port to the CPU port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN4Port |
1.3.6.1.4.1.27304.12.2.6 |
OBJECT IDENTIFIER |
|
|
|
feLAN4PortAutoNegotiation |
1.3.6.1.4.1.27304.12.2.6.1 |
Enables/disables auto negotiation on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..10 |
|
feLAN4PortSpeedMode |
1.3.6.1.4.1.27304.12.2.6.2 |
Sets/gets the speed and duplex mode on the port. Valid values are (100FD|100HD|10FD|10HD|AUTO|FD|HD) |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
feLAN4PortLinkStatus |
1.3.6.1.4.1.27304.12.2.6.3 |
Gets the Link status for the port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN4PortFlowControl |
1.3.6.1.4.1.27304.12.2.6.4 |
Enables/disables flow control on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN4PortIEEEQoSPriority |
1.3.6.1.4.1.27304.12.2.6.5 |
Enables prioritized frames based on there IEEE priority tags. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN4PortIPQoSPriority |
1.3.6.1.4.1.27304.12.2.6.6 |
Enables prioritized frames based on their IP4/IP6 priority fields. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN4PortFramePriorityOverwrite |
1.3.6.1.4.1.27304.12.2.6.7 |
Source Address(SA) or Destination Address(DA) Frame Priority Override on an ATU match. XX_FRAME_PRIO_OVERRIDE=0..1. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN4PortQueuePriorityOverwrite |
1.3.6.1.4.1.27304.12.2.6.8 |
Source Address(SA) or Destination Address(SA) Queue Priority Override on an ATU match. XX_QUEUE_PRIO_OVERRIDE=0..1. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN4PortQueuePriority |
1.3.6.1.4.1.27304.12.2.6.9 |
Queue priority, input parameters: PRIO:ENABLE PRIO: 0 - 7 ENABLE: 0 - 1 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN4PortQoSPortMapRule |
1.3.6.1.4.1.27304.12.2.6.10 |
Forces queue priority for a port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN4PortVIDNRLEnable |
1.3.6.1.4.1.27304.12.2.6.11 |
Enables/disables per port the Non rate limit for VLANs with the NRL bit enabled. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN4PortMap2PIRL |
1.3.6.1.4.1.27304.12.2.6.12 |
Adds/maps the port to a Port Ingress Rate Limitation (PIRL) bucket. Input parameter is PIRL bucket no 0 - 11. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..11 |
|
feLAN4PortDeletePortMap2PIRL |
1.3.6.1.4.1.27304.12.2.6.13 |
Deletes the port from a Port Ingress Rate Limitation (PIRL) bucket. Input parameter is PIRL bucket no 0 - 11. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..11 |
|
feLAN4PortIngressRateLimitation |
1.3.6.1.4.1.27304.12.2.6.15 |
Sets a Port Input Rate Limit(PIRL) bucket. Input parameters are: bucket:rate:layer:(DROP|FC) |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN4PortDefaultVLAN |
1.3.6.1.4.1.27304.12.2.6.16 |
Sets the default VLAN ID(VID) for the port. Input parameter is 0 - 4095 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
feLAN4PortForceDefaultVID |
1.3.6.1.4.1.27304.12.2.6.17 |
Forces the tagging of VID on all frames on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN4PortVLANPortMode |
1.3.6.1.4.1.27304.12.2.6.18 |
Sets the 802.1Q mode for the ingress port.
Mode either 0=disable,
1=fallback,
2=check,
3=secure |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..3 |
|
feLAN4PortBlockAllUnknown |
1.3.6.1.4.1.27304.12.2.6.19 |
This will make sure that all frames received on the port are blocked, unless they are tagged with the correct VID. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN4PortIGMPSnooping |
1.3.6.1.4.1.27304.12.2.6.20 |
Enables/disables IGMP snooping. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feLAN4PortAddUnicast |
1.3.6.1.4.1.27304.12.2.6.21 |
Adds the unicast mac address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aa:bb:cc:dd:ee:ff |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
feLAN4PortAddMulticast |
1.3.6.1.4.1.27304.12.2.6.22 |
Adds the IP multicast address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aaa.bbb.ccc.ddd |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
feLAN4PortArpMirroring |
1.3.6.1.4.1.27304.12.2.6.23 |
Mirror ARP packets seen on the port to the CPU port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
feModuleGroup |
1.3.6.1.4.1.27304.12.4 |
The objects are related to the DKTCOMEGA Fast Ethernet module, MIB rev 02_00. |
Status: current |
Access: read-write |
OBJECT-GROUP |
|
|
|