DKSF-70-6-X-X-1

File: DKSF-70-6-X-X-1.mib (35395 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-MIB

Imported symbols

enterprises MODULE-IDENTITY OBJECT-TYPE
Counter32 Gauge32 Counter64
Integer32 TimeTicks NOTIFICATION-TYPE
TEXTUAL-CONVENTION DisplayString TruthValue
TimeStamp snmpTraps

Defined Types

FixedPoint1000  
Fixed-point value as Integer, 3 decimal gigits after point (i.e. value*1000 rounded to Integer)
TEXTUAL-CONVENTION    
  INTEGER  

NpRelayEntry  
SEQUENCE    
  npRelayN INTEGER
  npRelayMode INTEGER
  npRelayStartReset INTEGER
  npRelayMemo DisplayString
  npRelayState INTEGER

NpThermoEntry  
SEQUENCE    
  npThermoSensorN INTEGER
  npThermoValue INTEGER
  npThermoStatus INTEGER
  npThermoLow INTEGER
  npThermoHigh INTEGER
  npThermoMemo DisplayString
  npThermoValuePrecise FixedPoint1000

NpIoEntry  
SEQUENCE    
  npIoLineN INTEGER
  npIoLevelIn INTEGER
  npIoLevelOut INTEGER
  npIoMemo DisplayString
  npIoPulseCounter Counter32
  npIoSinglePulseDuration INTEGER
  npIoSinglePulseStart INTEGER

NpCurLoopEntry  
SEQUENCE    
  npCurLoopN INTEGER
  npCurLoopStatus INTEGER
  npCurLoopI INTEGER
  npCurLoopV INTEGER
  npCurLoopR INTEGER
  npCurLoopPower INTEGER

NpSmokeEntry  
SEQUENCE    
  npSmokeSensorN INTEGER
  npSmokeStatus INTEGER
  npSmokePower INTEGER
  npSmokeReset INTEGER
  npSmokeMemo DisplayString

NpRelHumEntry  
SEQUENCE    
  npRelHumN INTEGER
  npRelHumValue INTEGER
  npRelHumStatus INTEGER
  npRelHumTempValue INTEGER
  npRelHumTempStatus INTEGER
  npRelHumMemo DisplayString
  npRelHumSafeRangeHigh INTEGER
  npRelHumSafeRangeLow INTEGER
  npRelHumTempSafeRangeHigh INTEGER
  npRelHumTempSafeRangeLow INTEGER

Defined Values

uniPingServerSolutionV3 1.3.6.1.4.1.25728.70
Generic MIB for NetPing remote sensing and control
MODULE-IDENTITY    

lightcom 1.3.6.1.4.1.25728
OBJECT IDENTIFIER    

npTrapInfo 1.3.6.1.4.1.25728.90
OBJECT IDENTIFIER    

npTrapEmailTo 1.3.6.1.4.1.25728.90.1
user-specified e-mail for NetPing Trap Forwarding Service
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npRelay 1.3.6.1.4.1.25728.5500
OBJECT IDENTIFIER    

npRelayTable 1.3.6.1.4.1.25728.5500.5
Watchdog and outlet/relay control table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NpRelayEntry

npRelayEntry 1.3.6.1.4.1.25728.5500.5.1
Relay/outlet table row
Status: current Access: not-accessible
OBJECT-TYPE    
  NpRelayEntry  

npRelayN 1.3.6.1.4.1.25728.5500.5.1.1
The N of output relay
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

npRelayMode 1.3.6.1.4.1.25728.5500.5.1.2
Control of relay: -1 - flip between on(1) and off(0) 0 - manual off 1 - manual on 2 - watchdog 3 - schedule 4 - both schedule and watchdog (while switched on by schedule) 5 - logic
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER flip(-1), off(0), on(1), watchdog(2), schedule(3), scheduleAndWatchdog(4), logic(5)  

npRelayStartReset 1.3.6.1.4.1.25728.5500.5.1.3
Write 1 to start reset (switch relay off for some time)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

npRelayMemo 1.3.6.1.4.1.25728.5500.5.1.6
Relay memo
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npRelayState 1.3.6.1.4.1.25728.5500.5.1.15
Actual relay state at the moment, regardless of source of control. 0 - relay is off 1 - relay is on
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER off(0), on(1)  

npThermo 1.3.6.1.4.1.25728.8800
OBJECT IDENTIFIER    

npThermoTable 1.3.6.1.4.1.25728.8800.1
Thermo Sensors Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NpThermoEntry

npThermoEntry 1.3.6.1.4.1.25728.8800.1.1
Thermo Sensors Table Row
Status: current Access: not-accessible
OBJECT-TYPE    
  NpThermoEntry  

npThermoSensorN 1.3.6.1.4.1.25728.8800.1.1.1
The id of temperature sensor, 1 to 8
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

npThermoValue 1.3.6.1.4.1.25728.8800.1.1.2
Temperature, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..280  

npThermoStatus 1.3.6.1.4.1.25728.8800.1.1.3
Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER failed(0), low(1), norm(2), high(3)  

npThermoLow 1.3.6.1.4.1.25728.8800.1.1.4
Bottom margin of normal temperature range, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..280  

npThermoHigh 1.3.6.1.4.1.25728.8800.1.1.5
Top margin of normal temperature range, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..280  

npThermoMemo 1.3.6.1.4.1.25728.8800.1.1.6
T channel memo
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npThermoValuePrecise 1.3.6.1.4.1.25728.8800.1.1.7
Temperature, deg.C, with fractional part 3 digits after point
Status: current Access: read-only
OBJECT-TYPE    
  FixedPoint1000  

npThermoTraps 1.3.6.1.4.1.25728.8800.2
OBJECT IDENTIFIER    

npThermoTrapPrefix 1.3.6.1.4.1.25728.8800.2.0
OBJECT IDENTIFIER    

npThermoTrapSensorN 1.3.6.1.4.1.25728.8800.2.1
The id of temperature sensor, 1 to 8
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

npThermoTrapValue 1.3.6.1.4.1.25728.8800.2.2
Temperature, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..280  

npThermoTrapStatus 1.3.6.1.4.1.25728.8800.2.3
Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER failed(0), low(1), norm(2), high(3)  

npThermoTrapLow 1.3.6.1.4.1.25728.8800.2.4
Bottom margin of normal temperature range, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..280  

npThermoTrapHigh 1.3.6.1.4.1.25728.8800.2.5
Top margin of normal temperature range, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..280  

npThermoTrapMemo 1.3.6.1.4.1.25728.8800.2.6
T channel memo
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npThermoTrap 1.3.6.1.4.1.25728.8800.2.0.1
Status of Thermo sensor is changed (crossing of normal temp. range)
Status: current Access: read-only
NOTIFICATION-TYPE    

npIo 1.3.6.1.4.1.25728.8900
OBJECT IDENTIFIER    

npIoTable 1.3.6.1.4.1.25728.8900.1
Digital Input/output Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NpIoEntry

npIoEntry 1.3.6.1.4.1.25728.8900.1.1
Digital Input/output Table Row
Status: current Access: not-accessible
OBJECT-TYPE    
  NpIoEntry  

npIoLineN 1.3.6.1.4.1.25728.8900.1.1.1
Number of IO line, from 1 to max supported
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

npIoLevelIn 1.3.6.1.4.1.25728.8900.1.1.2
Input level, 0 or 1
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

npIoLevelOut 1.3.6.1.4.1.25728.8900.1.1.3
Output level, 0 or 1. Write -1 to flip output.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER flip(-1), low(0), high(1)  

npIoMemo 1.3.6.1.4.1.25728.8900.1.1.6
IO line memo
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npIoPulseCounter 1.3.6.1.4.1.25728.8900.1.1.9
Pulse Counter on IO input line (counts positive fronts) Write 0 to reset.
Status: current Access: read-write
OBJECT-TYPE    
  Counter32  

npIoSinglePulseDuration 1.3.6.1.4.1.25728.8900.1.1.12
Set duration of single pulse on IO output line, 100ms to 25500ms, min. step is 100ms
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 100..25500  

npIoSinglePulseStart 1.3.6.1.4.1.25728.8900.1.1.13
Write 1 to start single pulse on IO output. Output will be inverted for time, specified by npIoSinglePulseDuration
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

npIoTraps 1.3.6.1.4.1.25728.8900.2
OBJECT IDENTIFIER    

npIoTrapPrefix 1.3.6.1.4.1.25728.8900.2.0
OBJECT IDENTIFIER    

npIoTrapLineN 1.3.6.1.4.1.25728.8900.2.1
Trap data, Number of IO line
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

npIoTrapLevelIn 1.3.6.1.4.1.25728.8900.2.2
Trap data, new Input level, 0 or 1
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

npIoTrapMemo 1.3.6.1.4.1.25728.8900.2.6
Trap data, IO line memo
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npIoTrapLevelLegend 1.3.6.1.4.1.25728.8900.2.7
Legend for current logic level on the IO line
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npIoTrap 1.3.6.1.4.1.25728.8900.2.0.1
Input state of IO line is changed
Status: current Access: read-only
NOTIFICATION-TYPE    

npCurLoop 1.3.6.1.4.1.25728.8300
OBJECT IDENTIFIER    

npCurLoopTable 1.3.6.1.4.1.25728.8300.1
Current loop sensors Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NpCurLoopEntry

npCurLoopEntry 1.3.6.1.4.1.25728.8300.1.1
Current loop sensors Table Row
Status: current Access: not-accessible
OBJECT-TYPE    
  NpCurLoopEntry  

npCurLoopN 1.3.6.1.4.1.25728.8300.1.1.1
Index of current loop, 1 to max supported
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

npCurLoopStatus 1.3.6.1.4.1.25728.8300.1.1.2
Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), alert(1), cut(2), short(3), notPowered(4)  

npCurLoopI 1.3.6.1.4.1.25728.8300.1.1.3
Loop current, mA
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..99999  

npCurLoopV 1.3.6.1.4.1.25728.8300.1.1.4
Voltage drop on the loop, mV
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..99999  

npCurLoopR 1.3.6.1.4.1.25728.8300.1.1.5
Resistance of the loop, Ohm
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..99999  

npCurLoopPower 1.3.6.1.4.1.25728.8300.1.1.7
Control of loop power 0=Off, 1=On, 2=reset by off/on power
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1), cyclePower(2)  

npCurLoopTraps 1.3.6.1.4.1.25728.8300.2
OBJECT IDENTIFIER    

npCurLoopTrapPrefix 1.3.6.1.4.1.25728.8300.2.0
OBJECT IDENTIFIER    

npCurLoopTrapN 1.3.6.1.4.1.25728.8300.2.1
Index of current loop, which status has changed
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

npCurLoopTrapStatus 1.3.6.1.4.1.25728.8300.2.2
Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), alert(1), cut(2), short(3), notPowered(4)  

npCurLoopTrapI 1.3.6.1.4.1.25728.8300.2.3
Loop current, mA
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..99999  

npCurLoopTrapV 1.3.6.1.4.1.25728.8300.2.4
Voltage drop on the loop, mV
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..99999  

npCurLoopTrapR 1.3.6.1.4.1.25728.8300.2.5
Resistance of the loop, Ohm
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..99999  

npCurLoopTrapPower 1.3.6.1.4.1.25728.8300.2.7
Status of loop power 0=Off, 1=On
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

npCurLoopTrap 1.3.6.1.4.1.25728.8300.2.0.1
Status of current loop N has changed!
Status: current Access: read-write
NOTIFICATION-TYPE    

npSmoke 1.3.6.1.4.1.25728.8200
OBJECT IDENTIFIER    

npSmokeTable 1.3.6.1.4.1.25728.8200.1
Smoke Sensors Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NpSmokeEntry

npSmokeEntry 1.3.6.1.4.1.25728.8200.1.1
Smoke Sensors Table Row
Status: current Access: not-accessible
OBJECT-TYPE    
  NpSmokeEntry  

npSmokeSensorN 1.3.6.1.4.1.25728.8200.1.1.1
The id of 1Wire Smoke sensor, 1 to 4
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

npSmokeStatus 1.3.6.1.4.1.25728.8200.1.1.2
Status of Smoke sensor
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), alarm(1), off(4), failed(5)  

npSmokePower 1.3.6.1.4.1.25728.8200.1.1.3
Controls power on Smoke sensor current loop
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

npSmokeReset 1.3.6.1.4.1.25728.8200.1.1.4
Write 1 to switch off for approx. 10s to reset sensor
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

npSmokeMemo 1.3.6.1.4.1.25728.8200.1.1.6
Smoke sensor memo
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npSmokeTraps 1.3.6.1.4.1.25728.8200.2
OBJECT IDENTIFIER    

npSmokeTrapPrefix 1.3.6.1.4.1.25728.8200.2.0
OBJECT IDENTIFIER    

npSmokeTrapSensorN 1.3.6.1.4.1.25728.8200.2.1
The id of 1Wire Smoke sensor, 1 to 4
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

npSmokeTrapStatus 1.3.6.1.4.1.25728.8200.2.2
New status of Smoke sensor
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), alarm(1), off(4), failed(5)  

npSmokeTrapMemo 1.3.6.1.4.1.25728.8200.2.6
Smoke sensor memo
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npSmokeTrap 1.3.6.1.4.1.25728.8200.2.0.1
Status of 1W Smoke sensor has changed
Status: current Access: read-only
NOTIFICATION-TYPE    

npRelHumidity 1.3.6.1.4.1.25728.8400
OBJECT IDENTIFIER    

npRelHumTable 1.3.6.1.4.1.25728.8400.1
Humidity+Temperature Sensors Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NpRelHumEntry

npRelHumEntry 1.3.6.1.4.1.25728.8400.1.1
Humidity+Temperature Sensors Table Row
Status: current Access: not-accessible
OBJECT-TYPE    
  NpRelHumEntry  

npRelHumN 1.3.6.1.4.1.25728.8400.1.1.1
Index of Humidity+Temperature sensor, 1 to max supported
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

npRelHumValue 1.3.6.1.4.1.25728.8400.1.1.2
Relative humidity value, %
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

npRelHumStatus 1.3.6.1.4.1.25728.8400.1.1.3
Status of Relative Humiduty
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sensorFailed(0), belowSafeRange(1), inSafeRange(2), aboveSafeRange(3)  

npRelHumTempValue 1.3.6.1.4.1.25728.8400.1.1.4
Sensor temperature, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..200  

npRelHumTempStatus 1.3.6.1.4.1.25728.8400.1.1.5
Status of Relative Humiduty
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sensorFailed(0), belowSafeRange(1), inSafeRange(2), aboveSafeRange(3)  

npRelHumMemo 1.3.6.1.4.1.25728.8400.1.1.6
Sensor Memo/Location
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npRelHumSafeRangeHigh 1.3.6.1.4.1.25728.8400.1.1.7
Relative Humidity safe range, top margin, %RH
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

npRelHumSafeRangeLow 1.3.6.1.4.1.25728.8400.1.1.8
Relative Humidity safe range, bottom margin, %RH
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

npRelHumTempSafeRangeHigh 1.3.6.1.4.1.25728.8400.1.1.9
Temperature safe range, top margin, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -55..150  

npRelHumTempSafeRangeLow 1.3.6.1.4.1.25728.8400.1.1.10
Temperature safe range, bottom margin, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -55..150  

npRelHumTrapData 1.3.6.1.4.1.25728.8400.3
OBJECT IDENTIFIER    

npRelHumTrapDataN 1.3.6.1.4.1.25728.8400.3.1
Index of Humidity+Temperature sensor, 1 to max supported
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

npRelHumTrapDataValue 1.3.6.1.4.1.25728.8400.3.2
Sensor humidity, %RH, or temperature, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

npRelHumTrapDataStatus 1.3.6.1.4.1.25728.8400.3.4
Status of humidity or temperature
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sensorFailed(0), belowSafeRange(1), inSafeRange(2), aboveSafeRange(3)  

npRelHumTrapDataMemo 1.3.6.1.4.1.25728.8400.3.6
Sensor Memo/Location
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npRelHumTrapDataSafeRangeHigh 1.3.6.1.4.1.25728.8400.3.7
Relative Humidity safe range, top margin, %RH or deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

npRelHumTrapDataSafeRangeLow 1.3.6.1.4.1.25728.8400.3.8
Relative Humidity safe range, bottom margin, %RH or deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

npRelHumTrap 1.3.6.1.4.1.25728.8400.6
OBJECT IDENTIFIER    

npRelHumTrapAllEvents 1.3.6.1.4.1.25728.8400.6.127
OBJECT IDENTIFIER    

npRelHumTrapTemp 1.3.6.1.4.1.25728.8400.7
OBJECT IDENTIFIER    

npRelHumTrapTempAllEvents 1.3.6.1.4.1.25728.8400.7.127
OBJECT IDENTIFIER    

npRelHumTrapAllChannels 1.3.6.1.4.1.25728.8400.6.127.99
Status of Humidity has changed!
Status: current Access: read-only
NOTIFICATION-TYPE    

npRelHumTrapAboveSafe 1.3.6.1.4.1.25728.8400.6.103
Humidity above the Safe range
Status: current Access: read-only
NOTIFICATION-TYPE    

npRelHumTrapSafe 1.3.6.1.4.1.25728.8400.6.102
Humidity in the Safe range
Status: current Access: read-only
NOTIFICATION-TYPE    

npRelHumTrapBelowSafe 1.3.6.1.4.1.25728.8400.6.101
Humidity below the Safe range
Status: current Access: read-only
NOTIFICATION-TYPE    

npRelHumTrapFail 1.3.6.1.4.1.25728.8400.6.100
Rel.Humidity sensor failed!
Status: current Access: read-only
NOTIFICATION-TYPE    

npRelHumTrapTempAllChannels 1.3.6.1.4.1.25728.8400.7.127.99
Status of Temperature has changed!
Status: current Access: read-only
NOTIFICATION-TYPE    

npRelHumTrapTempAboveSafe 1.3.6.1.4.1.25728.8400.7.103
Temperature above the Safe range
Status: current Access: read-only
NOTIFICATION-TYPE    

npRelHumTrapTempSafe 1.3.6.1.4.1.25728.8400.7.102
Temperature in the Safe range
Status: current Access: read-only
NOTIFICATION-TYPE    

npRelHumTrapTempBelowSafe 1.3.6.1.4.1.25728.8400.7.101
Temperature below the Safe range
Status: current Access: read-only
NOTIFICATION-TYPE    

npRelHumTrapTempFail 1.3.6.1.4.1.25728.8400.7.100
Sensor failed!
Status: current Access: read-only
NOTIFICATION-TYPE    

npGsm 1.3.6.1.4.1.25728.3800
OBJECT IDENTIFIER    

npGsmInfo 1.3.6.1.4.1.25728.3800.1
OBJECT IDENTIFIER    

npGsmFailed 1.3.6.1.4.1.25728.3800.1.1
Firmware's GSM module status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), failed(1), fatalError(2)  

npGsmRegistration 1.3.6.1.4.1.25728.3800.1.2
Status of modem registration in GSM network (AT+CREG? result)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER impossible(0), homeNetwork(1), searching(2), denied(3), unknown(4), roaming(5), infoUpdate(255)  

npGsmStrength 1.3.6.1.4.1.25728.3800.1.3
GSM signal strength. 0..31 = 0..100%, 99 = unknown or n/a, 255 = updating info
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

npGsmSendSmsUtf8 1.3.6.1.4.1.25728.3800.1.9
Send arbitrary SMS. Format: [phone_number,phone_number,...] Message One to four destination phone numbers If [] and numbers omitted, mesagge will be sent to preset numbers from SMS setup Cyrillic characters must be in UTF8 encoding.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

npGsmSendSmsWin1251 1.3.6.1.4.1.25728.3800.1.10
Send arbitrary SMS. Format: [phone_number,phone_number,...] Message One to four destination phone numbers If [] and numbers omitted, mesagge will be sent to preset numbers from SMS setup Cyrillic characters must be in Win1251 encoding.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

npGsmTraps 1.3.6.1.4.1.25728.3800.2
OBJECT IDENTIFIER    

npGsmTrapPrefix 1.3.6.1.4.1.25728.3800.2.0
OBJECT IDENTIFIER    

npGsmTrap 1.3.6.1.4.1.25728.3800.2.0.1
GSM modem or SMS firmware problems
Status: current Access: read-write
NOTIFICATION-TYPE    

npIr 1.3.6.1.4.1.25728.7900
OBJECT IDENTIFIER    

npIrCtrl 1.3.6.1.4.1.25728.7900.1
OBJECT IDENTIFIER    

npIrPlayCmd 1.3.6.1.4.1.25728.7900.1.1
Write IR command number to send IR command
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16  

npIrReset 1.3.6.1.4.1.25728.7900.1.2
Write 1 to reset IR transiever. After reset, send IR command and check npIrStatus.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

npIrStatus 1.3.6.1.4.1.25728.7900.1.3
IR transiever status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER commandCompleted(0), protocolError(1), commandAccepted(2), errorUnknown(16), errorBadNumber(17), errorEmptyRecord(18), errorFlashChip(19), errorTimeout(20), errorExtBusBusy(21)  

npReboot 1.3.6.1.4.1.25728.911
OBJECT IDENTIFIER    

npSoftReboot 1.3.6.1.4.1.25728.911.1
Write 1 to reboot device after current operations completition
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

npResetStack 1.3.6.1.4.1.25728.911.2
Write 1 to re-initialize network stack
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

npForcedReboot 1.3.6.1.4.1.25728.911.3
Write 1 to immediate forced reboot
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER