DGS3024-L2MGMT-MIB

File: DGS3024-L2MGMT-MIB.mib (62228 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC DLINK-ID-REC-MIB
SWDGS3024PRIMGMT-MIB

Imported symbols

IpAddress TimeTicks Integer32
MODULE-IDENTITY OBJECT-TYPE DisplayString
RowStatus AgentNotifyLevel dgs-3024Mgmt

Defined Types

MacAddress  
OCTET STRING Size(6)    

VlanId  
INTEGER 1..4094    

PortList  
OCTET STRING Size(0..127)    

SwL2PortInfoEntry  
SEQUENCE    
  swL2PortInfoPortIndex INTEGER
  swL2PortInfoUnitID INTEGER
  swL2PortInfoType INTEGER
  swL2PortInfoLinkStatus INTEGER
  swL2PortInfoNwayStatus INTEGER

SwL2PortCtrlEntry  
SEQUENCE    
  swL2PortCtrlPortIndex INTEGER
  swL2PortCtrlUnitIndex INTEGER
  swL2PortCtrlAdminState INTEGER
  swL2PortCtrlNwayState INTEGER
  swL2PortCtrlFlowCtrlState INTEGER
  swL2PortCtrlMACNotifyState INTEGER
  swL2PortCtrlDescription DisplayString

SwL2QOSBandwidthControlEntry  
SEQUENCE    
  swL2QOSBandwidthPortIndex INTEGER
  swL2QOSBandwidthRxRate INTEGER

SwL2QOSSchedulingEntry  
SEQUENCE    
  swL2QOSSchedulingClassIndex INTEGER
  swL2QOSSchedulingMaxPkts INTEGER

SwL2QOS8021pUserPriorityEntry  
SEQUENCE    
  swL2QOS8021pUserPriorityIndex INTEGER
  swL2QOS8021pUserPriorityClass INTEGER

SwL2QOS8021pDefaultPriorityEntry  
SEQUENCE    
  swL2QOS8021pDefaultPriorityIndex INTEGER
  swL2QOS8021pDefaultPriority INTEGER

SwL2TrunkCtrlEntry  
SEQUENCE    
  swL2TrunkIndex INTEGER
  swL2TrunkName DisplayString
  swL2TrunkMasterPort INTEGER
  swL2TrunkMember PortList
  swL2TrunkFloodingPort INTEGER
  swL2TrunkType INTEGER
  swL2TrunkState RowStatus

SwL2TrunkLACPPortEntry  
SEQUENCE    
  swL2TrunkLACPPortIndex INTEGER
  swL2TrunkLACPPortState INTEGER

SwL2IGMPCtrlEntry  
SEQUENCE    
  swL2IGMPCtrlVid INTEGER
  swL2IGMPQueryInterval INTEGER
  swL2IGMPMaxResponseTime INTEGER
  swL2IGMPRobustness INTEGER
  swL2IGMPLastMemberQueryInterval INTEGER
  swL2IGMPHostTimeout INTEGER
  swL2IGMPRouteTimeout INTEGER
  swL2IGMPLeaveTimer INTEGER
  swL2IGMPQueryState INTEGER
  swL2IGMPCurrentState INTEGER
  swL2IGMPCtrlState INTEGER

SwL2IGMPQueryInfoEntry  
SEQUENCE    
  swL2IGMPInfoVid INTEGER
  swL2IGMPInfoQueryCount INTEGER
  swL2IGMPInfoTxQueryCount INTEGER

SwL2IGMPInfoEntry  
SEQUENCE    
  swL2IGMPVid INTEGER
  swL2IGMPGroupIpAddr IpAddress
  swL2IGMPMacAddr MacAddress
  swL2IGMPPortMap PortList
  swL2IGMPIpGroupReportCount INTEGER

SwL2TrafficPortCtrlEntry  
SEQUENCE    
  swL2TrafficCtrlGroupIndex INTEGER
  swL2TrafficCtrlPortStatus INTEGER

Defined Values

swL2MgmtMIB 1.3.6.1.4.1.171.11.68.1.2
The Structure of Layer 2 Network Management Information
MODULE-IDENTITY    

swL2DevMgmt 1.3.6.1.4.1.171.11.68.1.2.1
OBJECT IDENTIFIER    

swL2PortMgmt 1.3.6.1.4.1.171.11.68.1.2.3
OBJECT IDENTIFIER    

swL2QOSMgmt 1.3.6.1.4.1.171.11.68.1.2.6
OBJECT IDENTIFIER    

swL2TrunkMgmt 1.3.6.1.4.1.171.11.68.1.2.9
OBJECT IDENTIFIER    

swL2MirrorMgmt 1.3.6.1.4.1.171.11.68.1.2.10
OBJECT IDENTIFIER    

swL2IGMPMgmt 1.3.6.1.4.1.171.11.68.1.2.11
OBJECT IDENTIFIER    

swL2TrafficMgmt 1.3.6.1.4.1.171.11.68.1.2.13
OBJECT IDENTIFIER    

swL2MgmtMIBTraps 1.3.6.1.4.1.171.11.68.1.2.15
OBJECT IDENTIFIER    

swL2DevInfo 1.3.6.1.4.1.171.11.68.1.2.1.1
OBJECT IDENTIFIER    

swDevInfoTotalNumOfPort 1.3.6.1.4.1.171.11.68.1.2.1.1.1
The number of ports within this switch. This value is the sum of the ports within this switch.
OBJECT-TYPE    
  INTEGER 0..65535  

swDevInfoNumOfPortInUse 1.3.6.1.4.1.171.11.68.1.2.1.1.2
The number of ports in this switch connected to the segment or the end stations.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2DevCtrl 1.3.6.1.4.1.171.11.68.1.2.1.2
OBJECT IDENTIFIER    

swL2DevCtrlStpState 1.3.6.1.4.1.171.11.68.1.2.1.2.1
This object can be enabled or disabled spanning tree algorithm during runtime of the system.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlIGMPSnooping 1.3.6.1.4.1.171.11.68.1.2.1.2.2
This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlRmonState 1.3.6.1.4.1.171.11.68.1.2.1.2.3
This object can be enabled or disabled RMON.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlCleanAllStatisticCounter 1.3.6.1.4.1.171.11.68.1.2.1.2.4
As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.
OBJECT-TYPE    
  INTEGER normal(1), active(2)  

swL2DevCtrlVlanIdOfFDBTbl 1.3.6.1.4.1.171.11.68.1.2.1.2.5
Indicates the VLAN ID which the Dot1dTpFdbTable belongs to ; The default value is DEFAULT_VLAN_ID of system .
OBJECT-TYPE    
  VlanId  

swL2MACNotifyState 1.3.6.1.4.1.171.11.68.1.2.1.2.6
This object can enabled or disabled MAC Notification.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2MACNotifyHistorySize 1.3.6.1.4.1.171.11.68.1.2.1.2.7
This object indicates the history size of variation MAC in address table. The default value is 1 .
OBJECT-TYPE    
  INTEGER 1..500  

swL2MACNotifyInterval 1.3.6.1.4.1.171.11.68.1.2.1.2.8
This object indicates the time interval in second for trigger the MAC notify message.
OBJECT-TYPE    
  INTEGER 1..2147483647  

swL2PortCtrlMulticastfilter 1.3.6.1.4.1.171.11.68.1.2.1.2.9
This object decide the multicast packets filtering mode on all port .
OBJECT-TYPE    
  INTEGER forward-unregistered-groups(2), filter-unregistered-groups(3)  

swL2DevAlarm 1.3.6.1.4.1.171.11.68.1.2.1.3
OBJECT IDENTIFIER    

swL2DevAlarmNewRoot 1.3.6.1.4.1.171.11.68.1.2.1.3.1
When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevAlarmTopologyChange 1.3.6.1.4.1.171.11.68.1.2.1.3.2
This object determine to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port tranition, the device doesn't send the trap if this object value is disabled or other.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevAlarmLinkChange 1.3.6.1.4.1.171.11.68.1.2.1.3.3
This object determine to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device doesn't send the trap if this object value is disabled or other.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortInfoTable 1.3.6.1.4.1.171.11.68.1.2.3.1
A table that contains information about every port.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortInfoEntry

swL2PortInfoEntry 1.3.6.1.4.1.171.11.68.1.2.3.1.1
A list of information for each port of the device.
OBJECT-TYPE    
  SwL2PortInfoEntry  

swL2PortInfoPortIndex 1.3.6.1.4.1.171.11.68.1.2.3.1.1.1
This object indicates the module's port number.(1..Max port number in the module)
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortInfoUnitID 1.3.6.1.4.1.171.11.68.1.2.3.1.1.2
Indicates ID of the unit in the system
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortInfoType 1.3.6.1.4.1.171.11.68.1.2.3.1.1.3
This object indicates the connector type of this port.
OBJECT-TYPE    
  INTEGER portType-100Base-TX(1), portType-100Base-FX(2), portType-100Base-FL(3), portType-1000Base-TX(4), portType-1000Base-SX(5), portType-1000Base-LX(6), portType-1000Base-SX-GBIC(7), portType-1000Base-LX-GBIC(8), portType-1000Base-TX-GBIC(9), portType-1000Base-1394(10), none(11)  

swL2PortInfoLinkStatus 1.3.6.1.4.1.171.11.68.1.2.3.1.1.4
This object indicates the port link status.
OBJECT-TYPE    
  INTEGER other(1), link-pass(2), link-fail(3)  

swL2PortInfoNwayStatus 1.3.6.1.4.1.171.11.68.1.2.3.1.1.5
This object indicates the port speed and duplex mode.
OBJECT-TYPE    
  INTEGER other(0), empty(1), link-down(2), half-10Mbps(3), full-10Mbps(4), half-100Mbps(5), full-100Mbps(6), half-1Gigabps(7), full-1Gigabps(8)  

swL2PortCtrlTable 1.3.6.1.4.1.171.11.68.1.2.3.2
A table that contains control information about every port.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortCtrlEntry

swL2PortCtrlEntry 1.3.6.1.4.1.171.11.68.1.2.3.2.1
A list of control information for each port of the device.
OBJECT-TYPE    
  SwL2PortCtrlEntry  

swL2PortCtrlPortIndex 1.3.6.1.4.1.171.11.68.1.2.3.2.1.1
This object indicates the module's port number.(1..Max port number in the module)
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortCtrlUnitIndex 1.3.6.1.4.1.171.11.68.1.2.3.2.1.2
Indicates ID of the unit in the device
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortCtrlAdminState 1.3.6.1.4.1.171.11.68.1.2.3.2.1.3
This object decide the port enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlNwayState 1.3.6.1.4.1.171.11.68.1.2.3.2.1.4
Chose the port speed, duplex mode, and N-Way function mode.
OBJECT-TYPE    
  INTEGER other(1), nway-enabled(2), nway-disabled-10Mbps-Half(3), nway-disabled-10Mbps-Full(4), nway-disabled-100Mbps-Half(5), nway-disabled-100Mbps-Full(6), nway-disabled-1Gigabps-Full-master(9), nway-disabled-1Gigabps-Full-slave(10)  

swL2PortCtrlFlowCtrlState 1.3.6.1.4.1.171.11.68.1.2.3.2.1.5
The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlMACNotifyState 1.3.6.1.4.1.171.11.68.1.2.3.2.1.7
This object set each poet MAC notification state.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlDescription 1.3.6.1.4.1.171.11.68.1.2.3.2.1.9
This object decide the description on this port.
OBJECT-TYPE    
  DisplayString Size(0..32)  

swL2QOSBandwidthControlTable 1.3.6.1.4.1.171.11.68.1.2.6.1
.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOSBandwidthControlEntry

swL2QOSBandwidthControlEntry 1.3.6.1.4.1.171.11.68.1.2.6.1.1
A list of information contained in swL2QOSBandwidthControlTable.
OBJECT-TYPE    
  SwL2QOSBandwidthControlEntry  

swL2QOSBandwidthPortIndex 1.3.6.1.4.1.171.11.68.1.2.6.1.1.1
Indicates the port .
OBJECT-TYPE    
  INTEGER 1..650  

swL2QOSBandwidthRxRate 1.3.6.1.4.1.171.11.68.1.2.6.1.1.2
Indicates RX Rate(Mbit/sec) of the specifed port. Value 1 means no limit.
OBJECT-TYPE    
  INTEGER no-limit(1), rx-64K(2), rx-128K(3), rx-256K(4), rx-512K(5), rx-1M(6), rx-2M(7), rx-4M(8), rx-8M(9), rx-16M(10), rx-32M(11), rx-64M(12), rx-128M(13), rx-256M(14), rx-512M(15)  

swL2QOSSchedulingTable 1.3.6.1.4.1.171.11.68.1.2.6.2
.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOSSchedulingEntry

swL2QOSSchedulingEntry 1.3.6.1.4.1.171.11.68.1.2.6.2.1
A list of information contained in swL2QOSSchedulingTable.
OBJECT-TYPE    
  SwL2QOSSchedulingEntry  

swL2QOSSchedulingClassIndex 1.3.6.1.4.1.171.11.68.1.2.6.2.1.1
Indicates the hardware queue number.
OBJECT-TYPE    
  INTEGER 0..3  

swL2QOSSchedulingMaxPkts 1.3.6.1.4.1.171.11.68.1.2.6.2.1.2
Indicates the max packet of QOS scheduling.
OBJECT-TYPE    
  INTEGER 0..15  

swL2QOS8021pUserPriorityTable 1.3.6.1.4.1.171.11.68.1.2.6.3
.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOS8021pUserPriorityEntry

swL2QOS8021pUserPriorityEntry 1.3.6.1.4.1.171.11.68.1.2.6.3.1
A list of information contained in swL2QOS8021pUserPriorityTable.
OBJECT-TYPE    
  SwL2QOS8021pUserPriorityEntry  

swL2QOS8021pUserPriorityIndex 1.3.6.1.4.1.171.11.68.1.2.6.3.1.1
The 802.1p user priority .
OBJECT-TYPE    
  INTEGER 0..7  

swL2QOS8021pUserPriorityClass 1.3.6.1.4.1.171.11.68.1.2.6.3.1.2
The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).
OBJECT-TYPE    
  INTEGER 0..3  

swL2QOS8021pDefaultPriorityTable 1.3.6.1.4.1.171.11.68.1.2.6.4
.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOS8021pDefaultPriorityEntry

swL2QOS8021pDefaultPriorityEntry 1.3.6.1.4.1.171.11.68.1.2.6.4.1
A list of information contained in swL2QOS8021pDefaultPriorityTable.
OBJECT-TYPE    
  SwL2QOS8021pDefaultPriorityEntry  

swL2QOS8021pDefaultPriorityIndex 1.3.6.1.4.1.171.11.68.1.2.6.4.1.1
Indicates the port number .
OBJECT-TYPE    
  INTEGER 1..650  

swL2QOS8021pDefaultPriority 1.3.6.1.4.1.171.11.68.1.2.6.4.1.2
The priority value to assign to untagged packets received by the switch ports on the switch..
OBJECT-TYPE    
  INTEGER 0..7  

swL2QOSSchedulingMechanismCtrl 1.3.6.1.4.1.171.11.68.1.2.6.5
This object can control QOS scheduling Mechanism.
OBJECT-TYPE    
  INTEGER strict(1), roundrobin(2)  

swL2TrunkMaxSupportedEntries 1.3.6.1.4.1.171.11.68.1.2.9.1
Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkCurrentNumEntries 1.3.6.1.4.1.171.11.68.1.2.9.2
Current actived number of entries in the trunk configuration table.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkCtrlTable 1.3.6.1.4.1.171.11.68.1.2.9.3
This table specifys which ports group a set of ports(up to 8) into a single logical link.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrunkCtrlEntry

swL2TrunkCtrlEntry 1.3.6.1.4.1.171.11.68.1.2.9.3.1
A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
OBJECT-TYPE    
  SwL2TrunkCtrlEntry  

swL2TrunkIndex 1.3.6.1.4.1.171.11.68.1.2.9.3.1.1
The index of logical port trunk. The trunk group number depend on the existence of unit and module.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkName 1.3.6.1.4.1.171.11.68.1.2.9.3.1.2
The name of logical port trunk.
OBJECT-TYPE    
  DisplayString Size(0..12)  

swL2TrunkMasterPort 1.3.6.1.4.1.171.11.68.1.2.9.3.1.3
The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
OBJECT-TYPE    
  INTEGER 1..65535  

swL2TrunkMember 1.3.6.1.4.1.171.11.68.1.2.9.3.1.4
Indicate how many number of ports is included in this Trunk. The trunk port number depend on the existence of module. The maximum number of ports is 8 for one trunks.
OBJECT-TYPE    
  PortList  

swL2TrunkFloodingPort 1.3.6.1.4.1.171.11.68.1.2.9.3.1.5
The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port.
OBJECT-TYPE    
  INTEGER 1..65535  

swL2TrunkType 1.3.6.1.4.1.171.11.68.1.2.9.3.1.6
This object indicated that type of the trunk group. static : is static trunk group lacp : is LACP trunk group .
OBJECT-TYPE    
  INTEGER other(1), static(2), lacp(3)  

swL2TrunkState 1.3.6.1.4.1.171.11.68.1.2.9.3.1.7
This object indicates the status of this entry.
OBJECT-TYPE    
  RowStatus  

swL2TrunkAlgorithm 1.3.6.1.4.1.171.11.68.1.2.9.4
This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.
OBJECT-TYPE    
  INTEGER other(1), mac-source(2), mac-destination(3), mac-source-dest(4)  

swL2TrunkLACPPortTable 1.3.6.1.4.1.171.11.68.1.2.9.5
This table specifys which ports group a set of ports(up to 8) into a single logical link.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrunkLACPPortEntry

swL2TrunkLACPPortEntry 1.3.6.1.4.1.171.11.68.1.2.9.5.1
A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
OBJECT-TYPE    
  SwL2TrunkLACPPortEntry  

swL2TrunkLACPPortIndex 1.3.6.1.4.1.171.11.68.1.2.9.5.1.1
The index of logical port lacp.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkLACPPortState 1.3.6.1.4.1.171.11.68.1.2.9.5.1.2
The state of logical port lacp.
OBJECT-TYPE    
  INTEGER active(1), passive(2)  

swL2MirrorLogicSourcePort 1.3.6.1.4.1.171.11.68.1.2.10.1
The port that will be mirrored. All packets entering and leaving the source port can be duplicated in the ingress_target and egress_target port port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2MirrorPortTargetIngress 1.3.6.1.4.1.171.11.68.1.2.10.2
Allows the mirroring of only packets received (flowing into) the port or ports in the port list.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2MirrorPortTargetEgress 1.3.6.1.4.1.171.11.68.1.2.10.3
Allows the mirroring of only packets sent (flowing out of) the port or ports in the port list.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2MirrorPortState 1.3.6.1.4.1.171.11.68.1.2.10.4
This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - writing this value to the object, and then the corresponding entry will be removed from the table. enabled(3) - this entry is reside in the table.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2IGMPMaxSupportedVlans 1.3.6.1.4.1.171.11.68.1.2.11.1
Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPCtrlTable).
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPMaxIpGroupNumPerVlan 1.3.6.1.4.1.171.11.68.1.2.11.2
Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPQueryInfoTable).
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPCtrlTable 1.3.6.1.4.1.171.11.68.1.2.11.3
The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with index range from 1 to 12.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPCtrlEntry

swL2IGMPCtrlEntry 1.3.6.1.4.1.171.11.68.1.2.11.3.1
The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.
OBJECT-TYPE    
  SwL2IGMPCtrlEntry  

swL2IGMPCtrlVid 1.3.6.1.4.1.171.11.68.1.2.11.3.1.1
This object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPQueryInterval 1.3.6.1.4.1.171.11.68.1.2.11.3.1.2
The frequency at which IGMP Host-Query packets are transmitted on this switch.
OBJECT-TYPE    
  INTEGER 1..65535  

swL2IGMPMaxResponseTime 1.3.6.1.4.1.171.11.68.1.2.11.3.1.3
The maximum query response time on this switch.
OBJECT-TYPE    
  INTEGER 1..25  

swL2IGMPRobustness 1.3.6.1.4.1.171.11.68.1.2.11.3.1.4
The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
OBJECT-TYPE    
  INTEGER 1..255  

swL2IGMPLastMemberQueryInterval 1.3.6.1.4.1.171.11.68.1.2.11.3.1.5
The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
OBJECT-TYPE    
  INTEGER 1..65535  

swL2IGMPHostTimeout 1.3.6.1.4.1.171.11.68.1.2.11.3.1.6
The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997.
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPRouteTimeout 1.3.6.1.4.1.171.11.68.1.2.11.3.1.7
The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPLeaveTimer 1.3.6.1.4.1.171.11.68.1.2.11.3.1.8
When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPQueryState 1.3.6.1.4.1.171.11.68.1.2.11.3.1.9
This object decide the IGMP query enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2IGMPCurrentState 1.3.6.1.4.1.171.11.68.1.2.11.3.1.10
This object indicates the current IGMP query state.
OBJECT-TYPE    
  INTEGER other(1), querier(2), non-querier(3)  

swL2IGMPCtrlState 1.3.6.1.4.1.171.11.68.1.2.11.3.1.11
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - IGMP funtion is enabled for this entry.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

swL2IGMPQueryInfoTable 1.3.6.1.4.1.171.11.68.1.2.11.4
The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPQueryInfoEntry

swL2IGMPQueryInfoEntry 1.3.6.1.4.1.171.11.68.1.2.11.4.1
Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled.
OBJECT-TYPE    
  SwL2IGMPQueryInfoEntry  

swL2IGMPInfoVid 1.3.6.1.4.1.171.11.68.1.2.11.4.1.1
This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoQueryCount 1.3.6.1.4.1.171.11.68.1.2.11.4.1.2
This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoTxQueryCount 1.3.6.1.4.1.171.11.68.1.2.11.4.1.3
This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoTable 1.3.6.1.4.1.171.11.68.1.2.11.5
The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPInfoEntry

swL2IGMPInfoEntry 1.3.6.1.4.1.171.11.68.1.2.11.5.1
Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled.
OBJECT-TYPE    
  SwL2IGMPInfoEntry  

swL2IGMPVid 1.3.6.1.4.1.171.11.68.1.2.11.5.1.1
This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPGroupIpAddr 1.3.6.1.4.1.171.11.68.1.2.11.5.1.2
This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.
OBJECT-TYPE    
  IpAddress  

swL2IGMPMacAddr 1.3.6.1.4.1.171.11.68.1.2.11.5.1.3
This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.
OBJECT-TYPE    
  MacAddress  

swL2IGMPPortMap 1.3.6.1.4.1.171.11.68.1.2.11.5.1.4
This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero.
OBJECT-TYPE    
  PortList  

swL2IGMPIpGroupReportCount 1.3.6.1.4.1.171.11.68.1.2.11.5.1.5
This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrafficCtrlBMStromthreshold 1.3.6.1.4.1.171.11.68.1.2.13.1
This object to decide how much thousand packets per second broadcast/multicast (depend on swL2TrafficCtrlBcastStromCtrl, swL2TrafficCtrlMcastStromCtrl or swL2TrafficCtrlDlfStromCtrl objects whether is enabled) will active storm control. Whenever a port reaches its configured amount of packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet.
OBJECT-TYPE    
  INTEGER packets-10(1), packets-100(2), packets-1000(3), packets-10000(4), packets-15000(5)  

swL2TrafficCtrlBcastStromCtrl 1.3.6.1.4.1.171.11.68.1.2.13.2
This object indicates broadcast storm control function is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrafficCtrlMcastStromCtrl 1.3.6.1.4.1.171.11.68.1.2.13.3
This object indicates multicast storm control function is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrafficCtrlDlfStromCtrl 1.3.6.1.4.1.171.11.68.1.2.13.4
This object indicates destination lookup fail function is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrafficPortCtrlTable 1.3.6.1.4.1.171.11.68.1.2.13.5
This table specifys the storm traffic control configuration.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrafficPortCtrlEntry

swL2TrafficPortCtrlEntry 1.3.6.1.4.1.171.11.68.1.2.13.5.1
A list of information specifies the storm traffic control configuration.
OBJECT-TYPE    
  SwL2TrafficPortCtrlEntry  

swL2TrafficCtrlGroupIndex 1.3.6.1.4.1.171.11.68.1.2.13.5.1.1
The index of logical port trunk. The trunk group number depend on the existence of unit and module.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrafficCtrlPortStatus 1.3.6.1.4.1.171.11.68.1.2.13.5.1.3
This object indicates destination lookup fail function is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2Notify 1.3.6.1.4.1.171.11.68.1.2.15.1
OBJECT IDENTIFIER    

swL2NotifyPrefix 1.3.6.1.4.1.171.11.68.1.2.15.1.2
OBJECT IDENTIFIER    

swL2NotifFirmware 1.3.6.1.4.1.171.11.68.1.2.15.1.2.0
OBJECT IDENTIFIER    

swL2macNotification 1.3.6.1.4.1.171.11.68.1.2.15.1.2.0.1
This trap indicates the mac addresses variation in address table .
NOTIFICATION-TYPE    

swL2porttypechg 1.3.6.1.4.1.171.11.68.1.2.15.1.2.0.2
This trap indicates the port type change.
NOTIFICATION-TYPE    

swl2NotificationBidings 1.3.6.1.4.1.171.11.68.1.2.15.1.2.1
OBJECT IDENTIFIER    

swL2macNotifyInfo 1.3.6.1.4.1.171.11.68.1.2.15.1.2.1.1
This object indicates the last time reboot information.
OBJECT-TYPE    
  OCTET STRING Size(0..1024)