DGS-3420-52T-L3MGMT-MIB

File: DGS-3420-52T-L3MGMT-MIB.mib (142124 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC IPV6-TC
SWDGS3420PRIMGMT-MIB OSPF-MIB IF-MIB

Imported symbols

Counter32 MODULE-IDENTITY OBJECT-TYPE
IpAddress NOTIFICATION-TYPE Integer32
Unsigned32 PhysAddress TruthValue
DisplayString RowStatus MacAddress
TimeStamp Ipv6Address dlink-Dgs3420Proj-Dgs3420-52T
TOSType Metric AreaID
RouterID UpToMaxAge HelloRange
PositiveInteger Status DesignatedRouterPriority
InterfaceIndex

Defined Types

NodeAddress  
OCTET STRING Size(6)    

NetAddress  
OCTET STRING Size(4)    

VrId  
A number which, along with an interface index (ifIndex), serves to uniquely identify a virtual router on a given VRRP router. A set of one or more associated addresses is assigned to a VRID.
TEXTUAL-CONVENTION    
  Integer32 1..255  

SwL3IpCtrlEntry  
SEQUENCE    
  swL3IpCtrlInterfaceName DisplayString
  swL3IpCtrlIfIndex INTEGER
  swL3IpCtrlIpAddr IpAddress
  swL3IpCtrlIpSubnetMask IpAddress
  swL3IpCtrlVlanName DisplayString
  swL3IpCtrlProxyArp INTEGER
  swL3IpCtrlSecondary TruthValue
  swL3IpCtrlMode INTEGER
  swL3IpCtrlAdminState INTEGER
  swL3IpCtrlIpv4AdminState INTEGER
  swL3IpCtrlIpv6AdminState INTEGER
  swL3IpCtrlIpv6LinkLocalAddress Ipv6Address
  swL3IpCtrlIpv6LinkLocalPrefixLen INTEGER
  swL3IpCtrlState RowStatus
  swL3IpCtrlIpv6LinkLocalAutoState INTEGER
  swL3IpCtrlLocalProxyArp INTEGER
  swL3IpCtrlIpMtu INTEGER
  swL3IpCtrlDhcpv6ClientState INTEGER
  swL3IpCtrlIpDirectedBroadcastState INTEGER
  swL3IpCtrlIpDhcpOption12State INTEGER
  swL3IpCtrlIpDhcpOption12HostName DisplayString
  swL3IpCtrlDhcpv6ClientPDState INTEGER
  swL3IpCtrlDhcpv6ClientPDPrefixName DisplayString
  swL3IpCtrlDhcpv6ClientPDPrefix Ipv6Address
  swL3IpCtrlDhcpv6ClientPDPrefixLen INTEGER
  swL3IpCtrlIpv6AutoConfigState INTEGER
  swL3IpCtrlIpv6AutoConfigDefault TruthValue
  swL3IpCtrlDhcpv6ClientRapidCommit TruthValue
  swL3IpCtrlDhcpv6ClientPdRapidCommit TruthValue

SwL3Ipv6CtrlEntry  
SEQUENCE    
  swL3Ipv6CtrlInterfaceName DisplayString
  swL3Ipv6CtrlMaxReassmblySize INTEGER
  swL3Ipv6CtrlNsRetransTimer Unsigned32
  swL3Ipv6CtrlRaState INTEGER
  swL3Ipv6CtrlRaMinRtrAdvInterval INTEGER
  swL3Ipv6CtrlRaMaxRtrAdvInterval INTEGER
  swL3Ipv6CtrlRaLifeTime INTEGER
  swL3Ipv6CtrlRaReachableTime INTEGER
  swL3Ipv6CtrlRaRetransTime Unsigned32
  swL3Ipv6CtrlRaHopLimit INTEGER
  swL3Ipv6CtrlRaManagedFlag INTEGER
  swL3Ipv6CtrlRaOtherConfigFlag INTEGER
  swL3Ipv6CtrlDadRetransNum INTEGER

SwL3Ipv6AddressCtrlEntry  
SEQUENCE    
  swL3Ipv6AddressCtrlInterfaceName DisplayString
  swL3Ipv6Address Ipv6Address
  swL3Ipv6AddressCtrlPrefixLen INTEGER
  swL3Ipv6AddressCtrlPreferredLifeTime Unsigned32
  swL3Ipv6AddressCtrlValidLifeTime Unsigned32
  swL3Ipv6AddressCtrlOnLinkFlag INTEGER
  swL3Ipv6AddressCtrlAutonomousFlag INTEGER
  swL3Ipv6AddressCtrlState RowStatus
  swL3Ipv6AddressCtrlAddressType INTEGER

SwL3Ipv6DHCPv6CPDAddrCtrlEntry  
SEQUENCE    
  swL3Ipv6DHCPv6CPDAddrCtrlInterfaceName DisplayString
  swL3Ipv6DHCPv6CPDAddrCtrlPrefixName DisplayString
  swL3Ipv6DHCPv6CPDAddrCtrlIPv6addr Ipv6Address
  swL3Ipv6DHCPv6CPDAddrCtrlPrefixLen INTEGER
  swL3Ipv6DHCPv6CPDAddrCtrlState RowStatus

SwL3LoopBackIpCtrlEntry  
SEQUENCE    
  swL3LoopBackIpCtrlInterfaceName DisplayString
  swL3LoopBackIpCtrlIfIndex INTEGER
  swL3LoopBackIpCtrlIpAddr IpAddress
  swL3LoopBackIpCtrlIpSubnetMask IpAddress
  swL3LoopBackIpCtrlAdminState INTEGER
  swL3LoopBackIpCtrlRowStatus RowStatus

SwL3LoopBackIpv6CtrlEntry  
SEQUENCE    
  swL3LoopBackIpv6CtrlInterfaceName DisplayString
  swL3LoopBackIpv6CtrlIpv6Address Ipv6Address
  swL3LoopBackIpv6CtrlIpv6PrefixLen INTEGER
  swL3LoopBackIpv6CtrlRowStatus RowStatus

SwL3IpFdbInfoEntry  
SEQUENCE    
  swL3IpFdbInfoIpAddr IpAddress
  swL3IpFdbInfoIpSubnetMask IpAddress
  swL3IpFdbInfoPort INTEGER
  swL3IpFdbInfoType INTEGER

SwL3IpStaticRouteEntry  
SEQUENCE    
  swL3IpStaticRouteDest IpAddress
  swL3IpStaticRouteMask IpAddress
  swL3IpStaticRouteBkupState INTEGER
  swL3IpStaticRouteNextHop IpAddress
  swL3IpStaticRouteMetric INTEGER
  swL3IpStaticRouteStatus INTEGER
  swL3IpStaticRouteWeight INTEGER
  swL3IpStaticRouteInterfaceName DisplayString

SwL3IpMcastStaticRouteEntry  
SEQUENCE    
  swL3IpMcastStaticRouteIpmrouteAddr IpAddress
  swL3IpMcastStaticRouteIpmrouteMask IpAddress
  swL3IpMcastStaticRouteRpfAddr IpAddress
  swL3IpMcastStaticRouteRowStatus RowStatus

SwL3IpStaticRouteTunnelEntry  
SEQUENCE    
  swL3IpStaticRouteTunnelInterfaceName DisplayString
  swL3IpStaticRouteTunnelRowStatus RowStatus

SwL3RelayDnsCtrlEntry  
SEQUENCE    
  swL3RelayDnsCtrlDomainName DisplayString
  swL3RelayDnsCtrlIpAddr IpAddress
  swL3RelayDnsCtrlState INTEGER

SwL3Md5Entry  
SEQUENCE    
  swL3Md5KeyId INTEGER
  swL3Md5Key DisplayString
  swL3Md5RowStatus RowStatus

SwL3RouteRedistriEntry  
SEQUENCE    
  swL3RouteRedistriSrcProtocol INTEGER
  swL3RouteRedistriDstProtocol INTEGER
  swL3RouteRedistriType INTEGER
  swL3RouteRedistriMetric Unsigned32
  swL3RouteRedistriRowStatus RowStatus
  swL3RouteRedistriRouteMapName DisplayString

SwL3OspfHostEntry  
SEQUENCE    
  swL3OspfHostIpAddress IpAddress
  swL3OspfHostTOS TOSType
  swL3OspfHostMetric Metric
  swL3OspfHostAreaID AreaID
  swL3OspfHostStatus RowStatus

SwL3OspfVirtIfEntry  
SEQUENCE    
  swL3ospfVirtIfAreaId AreaID
  swL3ospfVirtIfNeighbor RouterID
  swL3ospfVirtIfTransitDelay UpToMaxAge
  swL3ospfVirtIfRetransInterval UpToMaxAge
  swL3ospfVirtIfHelloInterval HelloRange
  swL3ospfVirtIfRtrDeadInterval Integer32
  swL3ospfVirtIfState INTEGER
  swL3ospfVirtIfEvents Counter32
  swL3ospfVirtIfAuthType INTEGER
  swL3ospfVirtIfAuthKey OCTET STRING
  swL3ospfVirtIfAuthKeyID INTEGER
  swL3ospfVirtIfStatus RowStatus

SwL3OspfIfEntry  
SEQUENCE    
  swL3ospfIfIpAddress IpAddress
  swL3ospfAddressLessIf Integer32
  swL3ospfIfAreaId AreaID
  swL3ospfIfType INTEGER
  swL3ospfIfAdminStat Status
  swL3ospfIfRtrPriority DesignatedRouterPriority
  swL3ospfIfTransitDelay UpToMaxAge
  swL3ospfIfRetransInterval UpToMaxAge
  swL3ospfIfHelloInterval HelloRange
  swL3ospfIfRtrDeadInterval PositiveInteger
  swL3ospfIfPollInterval PositiveInteger
  swL3ospfIfState INTEGER
  swL3ospfIfDesignatedRouter IpAddress
  swL3ospfIfBackupDesignatedRouter IpAddress
  swL3ospfIfEvents Counter32
  swL3ospfIfMulticastForwarding INTEGER
  swL3ospfIfDemand TruthValue
  swL3ospfIfAuthType INTEGER
  swL3ospfIfAuthKey OCTET STRING
  swL3ospfIfAuthKeyID INTEGER
  swL3ospfIfPassiveMode INTEGER
  swL3ospfIfMetric Metric
  swL3ospfIfDistributeListInType INTEGER
  swL3ospfIfDistributeListInName DisplayString

SwL3ospfAreaEntry  
SEQUENCE    
  swL3ospfAreaId AreaID
  swL3ospfAreaType INTEGER
  swL3ospfAreaSummaryState INTEGER
  swL3ospfAreaMetric Integer32
  swL3ospfAreaTranslateState INTEGER
  swL3ospfAreaStatus RowStatus

SwL3dvmrpInterfaceEntry  
SEQUENCE    
  swL3dvmrpInterfaceIfIndex Integer32
  swL3dvmrpInterfaceLocalAddress IpAddress
  swL3dvmrpInterfaceMetric Integer32
  swL3dvmrpInterfaceProbe Integer32
  swL3dvmrpInterfaceNbrTimeout Integer32
  swL3dvmrpInterfaceStatus RowStatus
  swL3dvmrpInterfaceRcvBadPkts Counter32
  swL3dvmrpInterfaceRcvBadRoutes Counter32

SwL3OspfInternalLsdbEntry  
SEQUENCE    
  swL3OspfInternalLsdbAreaId AreaID
  swL3OspfInternalLsdbType INTEGER
  swL3OspfInternalLsdbLsid IpAddress
  swL3OspfInternalLsdbRouterId RouterID
  swL3OspfInternalLsdbMetric Integer32
  swL3OspfInternalLsdbSequenceNo OCTET STRING
  swL3OspfInternalLsdbAge Unsigned32
  swL3OspfInternalLsdbChecksum Integer32

SwL3OspfExternalLsdbEntry  
SEQUENCE    
  swL3OspfExternalLsdbType INTEGER
  swL3OspfExternalLsdbLsid IpAddress
  swL3OspfExternalLsdbRouterId RouterID
  swL3OspfExternalLsdbMetric Integer32
  swL3OspfExternalLsdbMetricType INTEGER
  swL3OspfExternalLsdbSequenceNo OCTET STRING
  swL3OspfExternalLsdbAge Unsigned32
  swL3OspfExternalLsdbChecksum Integer32
  swL3OspfExternalLsdbForwardingAddress IpAddress
  swL3OspfExternalLsdbRouteTag OCTET STRING

SwL3VrrpOperEntry  
SEQUENCE    
  swL3VrrpOperIfIndex Integer32
  swL3VrrpOperVrId VrId
  swL3VrrpOperVirtualMacAddr MacAddress
  swL3VrrpOperState INTEGER
  swL3VrrpOperAdminState INTEGER
  swL3VrrpOperPriority Integer32
  swL3VrrpOperMasterIpAddr IpAddress
  swL3VrrpOperCriticalIpAddr IpAddress
  swL3VrrpOperCheckCriticalIpState INTEGER
  swL3VrrpOperAuthType INTEGER
  swL3VrrpOperAuthKey OCTET STRING
  swL3VrrpOperAdvertisementInterval Integer32
  swL3VrrpOperPreemptMode TruthValue
  swL3VrrpOperVirtualRouterUpTime TimeStamp
  swL3VrrpOperVirtualIpAddr IpAddress
  swL3VrrpOperRowStatus RowStatus

SwL3RIPInboundRouteFilterEntry  
SEQUENCE    
  swL3RIPInboundRouteFilterIfIpAddress IpAddress
  swL3RIPInboundRouteFilterType INTEGER
  swL3RIPInboundRouteFilterName DisplayString

SwL3Route6RedistriEntry  
SEQUENCE    
  swL3Route6RedistriSrcProtocol INTEGER
  swL3Route6RedistriDstProtocol INTEGER
  swL3Route6RedistriType INTEGER
  swL3Route6RedistriMetric Unsigned32
  swL3Route6RedistriRowStatus RowStatus

Defined Values

swL3MgmtMIB 1.3.6.1.4.1.171.11.119.4.3
The Structure of Layer 3 Network Management Information for the proprietary enterprise.
MODULE-IDENTITY    

swL3DevMgmt 1.3.6.1.4.1.171.11.119.4.3.1
OBJECT IDENTIFIER    

swL3IpMgmt 1.3.6.1.4.1.171.11.119.4.3.2
OBJECT IDENTIFIER    

swL3RelayMgmt 1.3.6.1.4.1.171.11.119.4.3.3
OBJECT IDENTIFIER    

swL3IpMcastMgmt 1.3.6.1.4.1.171.11.119.4.3.2.6
OBJECT IDENTIFIER    

swL3OspfLsdbMgmt 1.3.6.1.4.1.171.11.119.4.3.13
OBJECT IDENTIFIER    

swL3VrrpOperMgmt 1.3.6.1.4.1.171.11.119.4.3.14
OBJECT IDENTIFIER    

swL3IpCtrlMgmt 1.3.6.1.4.1.171.11.119.4.3.2.1
OBJECT IDENTIFIER    

swL3IpFdbMgmt 1.3.6.1.4.1.171.11.119.4.3.2.2
OBJECT IDENTIFIER    

swL3RelayDnsMgmt 1.3.6.1.4.1.171.11.119.4.3.3.3
OBJECT IDENTIFIER    

swL3OspfECMPMgmt 1.3.6.1.4.1.171.11.119.4.3.15
OBJECT IDENTIFIER    

swL3RIPTimerMgmt 1.3.6.1.4.1.171.11.119.4.3.17
OBJECT IDENTIFIER    

swL3OspfDefInfoOrigMgmt 1.3.6.1.4.1.171.11.119.4.3.18
OBJECT IDENTIFIER    

swL3DevCtrl 1.3.6.1.4.1.171.11.119.4.3.1.1
OBJECT IDENTIFIER    

swL3DevCtrlRIPState 1.3.6.1.4.1.171.11.119.4.3.1.1.1
This object indicates if the Routing Information Protocol (RIP) version 2 function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3DevCtrlOSPFState 1.3.6.1.4.1.171.11.119.4.3.1.1.2
This object indicates OSPF protocol is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3DevCtrlDVMRPState 1.3.6.1.4.1.171.11.119.4.3.1.1.3
This object indicates if the DVMRP protocol is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3DevCtrlVRRPState 1.3.6.1.4.1.171.11.119.4.3.1.1.5
This object indicates VRRP protocol is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3DevCtrlVrrpPingState 1.3.6.1.4.1.171.11.119.4.3.1.1.6
This object indicates VRRP protocol Ping is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3IpCtrlTable 1.3.6.1.4.1.171.11.119.4.3.2.1.3
This table contain IP interface information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3IpCtrlEntry

swL3IpCtrlEntry 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1
A list of information about a specific IP interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3IpCtrlEntry  

swL3IpCtrlInterfaceName 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.1
This object indicates the name of the IP interface.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..12)  

swL3IpCtrlIfIndex 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.2
This object uniquely identifies the IP interface number in the swL3IpCtrlTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL3IpCtrlIpAddr 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.3
The IP address of the interface. This object only can take the value of the unicast IP address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL3IpCtrlIpSubnetMask 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.4
The IP net mask for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL3IpCtrlVlanName 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.5
This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

swL3IpCtrlProxyArp 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.6
This object indicates enable/disable of the proxy ARP function for IPv4.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3IpCtrlSecondary 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.7
When this is true(1), the IP address is the secondary IP. When false(2), the IP address is the primary IP.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

swL3IpCtrlMode 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.8
This object indicates the IP operation mode. other(1) - This entry is currently in use but the conditions under which it will remain are determined by each of the following values. bootp(3) - The IP address will be set automatically from a BOOTP server. dhcp(4) - The IP address will be set automatically from a DHCP server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), bootp(3), dhcp(4)  

swL3IpCtrlAdminState 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.9
The state of the IP interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3IpCtrlIpv4AdminState 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.10
The IPv4 admin state of the IP interface. The default state is determined by project. This state will only be effective when the swL3IpCtrlAdminState is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3IpCtrlIpv6AdminState 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.12
The IPv6 admin state of the IP interface. The default state is determined by project. This state will only be effective when the swL3IpCtrlAdminState is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3IpCtrlIpv6LinkLocalAddress 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.14
The IPv6 link local address for this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6Address  

swL3IpCtrlIpv6LinkLocalPrefixLen 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.15
The IPv6 prefix length for this IPv6 link local address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swL3IpCtrlState 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.16
This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3IpCtrlIpv6LinkLocalAutoState 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.17
The state of the IPv6 link local auto.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), enabled(2), disabled(3)  

swL3IpCtrlLocalProxyArp 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.18
This object indicates enable/disable of the local proxy ARP function for IPv4.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3IpCtrlIpMtu 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.19
The MTU is the largest size of the IP datagram which may be transferred using a specific data link connection. The MTU value is a design parameter of a LAN and is a mutually agreed value (i.e. both ends of a link agree to use the same specific value) for most WAN links. The MTU range is based on the chip of the current device. The suggested minimum value is 1500 bytes. The suggested maximum value is the size of the jumbo frame minus 36. The suggested default setting is 1500 bytes.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

swL3IpCtrlDhcpv6ClientState 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.20
The state of the Dhcpv6 Client.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3IpCtrlIpDirectedBroadcastState 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.21
The state of the IP Directed Broadcast.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3IpCtrlIpDhcpOption12State 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.22
Enable or disable insertion of option 12 in the DHCPDISCOVER and DHCPREQUEST message.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3IpCtrlIpDhcpOption12HostName 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.23
Specify the host name to be inserted in the DHCPDISCOVER and DHCPREQUEST message. The specified host name must start with a letter, end with a letter or digit, and have only letters, digits, and hyphen as interior characters; the maximal length is 63. By default, the host name is empty. When set an empty host name, means to clear the host name setting and use the default value to encode option 12.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

swL3IpCtrlDhcpv6ClientPDState 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.24
The state of the Dhcpv6 Client PD.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3IpCtrlDhcpv6ClientPDPrefixName 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.25
This object indicates the name for the DHCPv6 Client PD. If the swL3IpCtrlDhcpv6ClientPDState is disabled, this object will be clear and can't write.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..12)  

swL3IpCtrlDhcpv6ClientPDPrefix 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.26
The IPv6 prefix obtained form delegation router.
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6Address  

swL3IpCtrlDhcpv6ClientPDPrefixLen 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.27
The IPv6 prefix length for the prefix obtained from delegation router.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swL3IpCtrlIpv6AutoConfigState 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.28
The state of IPv6 stateless adddress autoconfig.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3IpCtrlIpv6AutoConfigDefault 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.29
When this is true(1), a default route will be installed into ipv6 routing table. When false(2), no default route will be installed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

swL3IpCtrlDhcpv6ClientRapidCommit 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.30
When this is true(1), Allows the two-message exchange method for address assignment.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

swL3IpCtrlDhcpv6ClientPdRapidCommit 1.3.6.1.4.1.171.11.119.4.3.2.1.3.1.31
When this is true(1), Allows the two-message exchange method for prefix assignment.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

swL3Ipv6CtrlTable 1.3.6.1.4.1.171.11.119.4.3.2.1.4
This table contains IPv6 information of an IP interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3Ipv6CtrlEntry

swL3Ipv6CtrlEntry 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1
A list of IPv6 information about a specific IP interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3Ipv6CtrlEntry  

swL3Ipv6CtrlInterfaceName 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1.1
This object indicates the name of the IP interface.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..12)  

swL3Ipv6CtrlMaxReassmblySize 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1.2
Maximum Reassembly Size of the IP interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swL3Ipv6CtrlNsRetransTimer 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1.3
Neighbor solicitation's retransmit timer. The unit is set in milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4294967295  

swL3Ipv6CtrlRaState 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1.5
Neighbor solicited state.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3Ipv6CtrlRaMinRtrAdvInterval 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1.6
The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInterval. Default value: 0.33 * MaxRtrAdvInterval
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 3..1350  

swL3Ipv6CtrlRaMaxRtrAdvInterval 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1.7
The maximum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 4..1800  

swL3Ipv6CtrlRaLifeTime 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1.8
Indicates the lifetime of the router as the default router.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..9000  

swL3Ipv6CtrlRaReachableTime 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1.9
Indicates the amount of time that a node can consider a neighboring node reachable after receiving a reachability confirmation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..3600000  

swL3Ipv6CtrlRaRetransTime 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1.10
Indicates the amount of time between retransmissions of neighbor solicited messages. The unit is set in millisecond.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4294967295  

swL3Ipv6CtrlRaHopLimit 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1.11
Indicates the default value of the hop limit field in the IPv6 header for packets sent by hosts that receive this RA message.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

swL3Ipv6CtrlRaManagedFlag 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1.12
When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an address in the addition to the addresses derived from the stateless address configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3Ipv6CtrlRaOtherConfigFlag 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1.13
When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an on-link address configuration information.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3Ipv6CtrlDadRetransNum 1.3.6.1.4.1.171.11.119.4.3.2.1.4.1.14
Indicates the value of duplicate address detection attempt number
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

swL3Ipv6CtrlOptimisticDadState 1.3.6.1.4.1.171.11.119.4.3.2.1.4.2
Indicates the status of optimistic dad.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3Ipv6AddressCtrlTable 1.3.6.1.4.1.171.11.119.4.3.2.1.5
This table contains IPv6 address information for each IP interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3Ipv6AddressCtrlEntry

swL3Ipv6AddressCtrlEntry 1.3.6.1.4.1.171.11.119.4.3.2.1.5.1
A list of information about a specific IPv6 address.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3Ipv6AddressCtrlEntry  

swL3Ipv6AddressCtrlInterfaceName 1.3.6.1.4.1.171.11.119.4.3.2.1.5.1.1
This object indicates the name of the IP interface.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..12)  

swL3Ipv6Address 1.3.6.1.4.1.171.11.119.4.3.2.1.5.1.2
Specify the IPv6 address.
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6Address  

swL3Ipv6AddressCtrlPrefixLen 1.3.6.1.4.1.171.11.119.4.3.2.1.5.1.3
Indicates the prefix length of this IPv6 address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swL3Ipv6AddressCtrlPreferredLifeTime 1.3.6.1.4.1.171.11.119.4.3.2.1.5.1.4
Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains in preferred state. For an infinite valid lifetime, the value can be set to 0xffffffff.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4294967294  

swL3Ipv6AddressCtrlValidLifeTime 1.3.6.1.4.1.171.11.119.4.3.2.1.5.1.5
Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains valid. For an infinite valid lifetime, the value can be set to 0xffffffff.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4294967294  

swL3Ipv6AddressCtrlOnLinkFlag 1.3.6.1.4.1.171.11.119.4.3.2.1.5.1.6
When enabled, the address implied by the specified prefix is available on the link where the RA message is received.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3Ipv6AddressCtrlAutonomousFlag 1.3.6.1.4.1.171.11.119.4.3.2.1.5.1.7
When enabled, the specified prefix will be used to create an autonomous address configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3Ipv6AddressCtrlState 1.3.6.1.4.1.171.11.119.4.3.2.1.5.1.8
This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3Ipv6AddressCtrlAddressType 1.3.6.1.4.1.171.11.119.4.3.2.1.5.1.9
This object indicates the type of the IPv6 address. manual(1): the IPv6 address is configured by user. dhcpv6(2): the IPv6 address is assigned by DHCPv6 server. stateless(3): the IPv6 address is assigned by router advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER manual(1), dhcpv6(2), stateless(3)  

swL3Ipv6DHCPv6CPDAddrCtrlTable 1.3.6.1.4.1.171.11.119.4.3.2.1.6
This table contain the information of the IPv6 address which based on DHCPv6 client PD.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3Ipv6DHCPv6CPDAddrCtrlEntry

swL3Ipv6DHCPv6CPDAddrCtrlEntry 1.3.6.1.4.1.171.11.119.4.3.2.1.6.1
A list of information about a specific DHCPv6 Client PD IPv6 address.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3Ipv6DHCPv6CPDAddrCtrlEntry  

swL3Ipv6DHCPv6CPDAddrCtrlInterfaceName 1.3.6.1.4.1.171.11.119.4.3.2.1.6.1.1
This object indicates the name of the IP interface.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..12)  

swL3Ipv6DHCPv6CPDAddrCtrlPrefixName 1.3.6.1.4.1.171.11.119.4.3.2.1.6.1.2
This object indicates the name of the prefix based on which the IPv6 address will be generate.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..12)  

swL3Ipv6DHCPv6CPDAddrCtrlIPv6addr 1.3.6.1.4.1.171.11.119.4.3.2.1.6.1.3
Specify the suffix of the IPv6 address.
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6Address  

swL3Ipv6DHCPv6CPDAddrCtrlPrefixLen 1.3.6.1.4.1.171.11.119.4.3.2.1.6.1.4
Indicates the prefix length of this IPv6 address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swL3Ipv6DHCPv6CPDAddrCtrlState 1.3.6.1.4.1.171.11.119.4.3.2.1.6.1.5
This variable displays the status of the entry. The status is used for creating and deleting instances of the objects in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3IpCtrlAllIpIfState 1.3.6.1.4.1.171.11.119.4.3.2.1.7
This object indicates all interface function state of the device. (except the loopback interface)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), enabled(2), disabled(3)  

swL3LoopBackIpCtrlTable 1.3.6.1.4.1.171.11.119.4.3.2.1.8
This table contains loopback IP interface information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3LoopBackIpCtrlEntry

swL3LoopBackIpCtrlEntry 1.3.6.1.4.1.171.11.119.4.3.2.1.8.1
A list of information about a specific loopback IP interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3LoopBackIpCtrlEntry  

swL3LoopBackIpCtrlInterfaceName 1.3.6.1.4.1.171.11.119.4.3.2.1.8.1.1
This object indicates the name of the loopback IP interface.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..12)  

swL3LoopBackIpCtrlIfIndex 1.3.6.1.4.1.171.11.119.4.3.2.1.8.1.2
This object uniquely identifies the loopback IP interface number in the swL3LoopBackIpCtrlTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL3LoopBackIpCtrlIpAddr 1.3.6.1.4.1.171.11.119.4.3.2.1.8.1.3
The IP address of the loopback interface. This object only can take the value of the unicast IP address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

swL3LoopBackIpCtrlIpSubnetMask 1.3.6.1.4.1.171.11.119.4.3.2.1.8.1.4
The IP net mask for this loopback interface.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

swL3LoopBackIpCtrlAdminState 1.3.6.1.4.1.171.11.119.4.3.2.1.8.1.5
The state of the loopback IP interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3LoopBackIpCtrlRowStatus 1.3.6.1.4.1.171.11.119.4.3.2.1.8.1.6
This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3LoopBackIpv6CtrlTable 1.3.6.1.4.1.171.11.119.4.3.2.1.9
This table contains loopback IPv6 interface information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3LoopBackIpv6CtrlEntry

swL3LoopBackIpv6CtrlEntry 1.3.6.1.4.1.171.11.119.4.3.2.1.9.1
A list of information about a specific loopback IPv6 interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3LoopBackIpv6CtrlEntry  

swL3LoopBackIpv6CtrlInterfaceName 1.3.6.1.4.1.171.11.119.4.3.2.1.9.1.1
This object indicates the name of the loopback IP interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..12)  

swL3LoopBackIpv6CtrlIpv6Address 1.3.6.1.4.1.171.11.119.4.3.2.1.9.1.2
The IPv6 address of the loopback interface. This object only can take the value of the unicast IPv6 address.
Status: current Access: not-accessible
OBJECT-TYPE    
  Ipv6Address  

swL3LoopBackIpv6CtrlIpv6PrefixLen 1.3.6.1.4.1.171.11.119.4.3.2.1.9.1.3
The IPv6 prefix for this loopback interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

swL3LoopBackIpv6CtrlRowStatus 1.3.6.1.4.1.171.11.119.4.3.2.1.9.1.99
This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3IpFdbInfoTable 1.3.6.1.4.1.171.11.119.4.3.2.2.1
A table that contains forwarding and/or filtering information. This information is used by the switch in determining how to propagate the received IP packets.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3IpFdbInfoEntry

swL3IpFdbInfoEntry 1.3.6.1.4.1.171.11.119.4.3.2.2.1.1
Information about a specific IP address for which the bridge has some forwarding and/or filtering information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3IpFdbInfoEntry  

swL3IpFdbInfoIpAddr 1.3.6.1.4.1.171.11.119.4.3.2.2.1.1.1
A IP address for which switch has forwarding and/or filtering information.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3IpFdbInfoIpSubnetMask 1.3.6.1.4.1.171.11.119.4.3.2.2.1.1.2
A IP net mask for this interface for which the switch has forwarding and/or filtering information.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3IpFdbInfoPort 1.3.6.1.4.1.171.11.119.4.3.2.2.1.1.3
Either the value '0', or the port number of the port on which packets having an IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr has been seen. A value of '0' indicates that the port number has not been learned but that switch does have some forwarding/filtering information about this address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL3IpFdbInfoType 1.3.6.1.4.1.171.11.119.4.3.2.2.1.1.4
The status of this entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), static(2), dynamic(3)  

swL3IpArpAgingTime 1.3.6.1.4.1.171.11.119.4.3.2.4
The timeout period in minutes for aging out dynamically learned arp information.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

swL3IpStaticRouteTable 1.3.6.1.4.1.171.11.119.4.3.2.5
This entity's IP static Routing table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3IpStaticRouteEntry

swL3IpStaticRouteEntry 1.3.6.1.4.1.171.11.119.4.3.2.5.1
A particular route to a particular destination, under a particular policy. Once an entry is built,it shouldn't be modified.That is,it just supports create and delete actions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3IpStaticRouteEntry  

swL3IpStaticRouteDest 1.3.6.1.4.1.171.11.119.4.3.2.5.1.1
The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteMask object is not equal to x.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3IpStaticRouteMask 1.3.6.1.4.1.171.11.119.4.3.2.5.1.2
Indicate the mask to be logical-AND with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the swL3IpStaticRouteMask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteDest object is not equal to swL3IpStaticRouteDest.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3IpStaticRouteBkupState 1.3.6.1.4.1.171.11.119.4.3.2.5.1.3
The routing state for this route.The value SHOULD be primary(1), backup(2) or none(3).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER primary(1), backup(2), none(3)  

swL3IpStaticRouteNextHop 1.3.6.1.4.1.171.11.119.4.3.2.5.1.4
Specifies the IP address for the next hop router. An IP address of 255.255.255.255 denotes a Null interface as the next hop.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

swL3IpStaticRouteMetric 1.3.6.1.4.1.171.11.119.4.3.2.5.1.5
Specifies the routing metric for this route. If this metric is not used, its value will be displayed as -1.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..65535  

swL3IpStaticRouteStatus 1.3.6.1.4.1.171.11.119.4.3.2.5.1.6
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry resides in the table. active(4) - the nextHop of this entry exists in the ARP table. inActive(5) - the next hop of this entry does not exist in the ARP table.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3), active(4), inActive(5)  

swL3IpStaticRouteWeight 1.3.6.1.4.1.171.11.119.4.3.2.5.1.7
Specifies the weight value. Used for the weighted multipath.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..4  

swL3IpStaticRouteInterfaceName 1.3.6.1.4.1.171.11.119.4.3.2.5.1.8
Specifies the name of the IP interface.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

swL3IpMcastStaticRouteTable 1.3.6.1.4.1.171.11.119.4.3.2.6.1
IP multicast static routing allows you to have multicast paths diverge from the unicast paths.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3IpMcastStaticRouteEntry

swL3IpMcastStaticRouteEntry 1.3.6.1.4.1.171.11.119.4.3.2.6.1.1
A list of information about IP multicast static routes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3IpMcastStaticRouteEntry  

swL3IpMcastStaticRouteIpmrouteAddr 1.3.6.1.4.1.171.11.119.4.3.2.6.1.1.1
If the source IP address of the received IP multicast packet matches this Ipmrouteaddress, the RPF network is used to do an RPF check.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

swL3IpMcastStaticRouteIpmrouteMask 1.3.6.1.4.1.171.11.119.4.3.2.6.1.1.2
This specifies an IP net Mask for this interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

swL3IpMcastStaticRouteRpfAddr 1.3.6.1.4.1.171.11.119.4.3.2.6.1.1.3
If the source IP address of the received IP multicast packet matches the Ipmrouteaddress, the Rpfaddress will be used to check whether the packet received is from a legal interface. If it is set to null, it means that if the source IP address in the received IP multicast packet matches the Ipmrouteaddress, the RPF check will fail.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

swL3IpMcastStaticRouteRowStatus 1.3.6.1.4.1.171.11.119.4.3.2.6.1.1.4
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3IpStaticRouteTunnelTable 1.3.6.1.4.1.171.11.119.4.3.2.7
This entity's IPv4 static Routing tunnel table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3IpStaticRouteTunnelEntry

swL3IpStaticRouteTunnelEntry 1.3.6.1.4.1.171.11.119.4.3.2.7.1
A particular route to a particular destination, under a particular policy. Once an entry is built, it cannot be modified. That is, it just supports create and delete actions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3IpStaticRouteTunnelEntry  

swL3IpStaticRouteTunnelInterfaceName 1.3.6.1.4.1.171.11.119.4.3.2.7.1.1
This object indicates the name of the IP tunnel interface.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

swL3IpStaticRouteTunnelRowStatus 1.3.6.1.4.1.171.11.119.4.3.2.7.1.2
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3RelayDnsState 1.3.6.1.4.1.171.11.119.4.3.3.3.1
This object indicates if the DNS Relay function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3RelayDnsPrimaryServer 1.3.6.1.4.1.171.11.119.4.3.3.3.2
This object indicates the address of the primary DNS server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL3RelayDnsSecondaryServer 1.3.6.1.4.1.171.11.119.4.3.3.3.3
This object indicates the address of the secondary DNS server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL3RelayDnsCacheState 1.3.6.1.4.1.171.11.119.4.3.3.3.4
This object indicates DNS Relay cache is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3RelayDnsStaticTableState 1.3.6.1.4.1.171.11.119.4.3.3.3.5
This object indicates DNS Relay static table is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3RelayDnsCtrlTable 1.3.6.1.4.1.171.11.119.4.3.3.3.6
This table displays the current DNS relay static table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3RelayDnsCtrlEntry

swL3RelayDnsCtrlEntry 1.3.6.1.4.1.171.11.119.4.3.3.3.6.1
A list of information display the current DNS relay static table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3RelayDnsCtrlEntry  

swL3RelayDnsCtrlDomainName 1.3.6.1.4.1.171.11.119.4.3.3.3.6.1.1
The domain name of the entry.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

swL3RelayDnsCtrlIpAddr 1.3.6.1.4.1.171.11.119.4.3.3.3.6.1.2
The IP address of the entry.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3RelayDnsCtrlState 1.3.6.1.4.1.171.11.119.4.3.3.3.6.1.3
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

swL3Md5Table 1.3.6.1.4.1.171.11.119.4.3.4
This table displays the current MD5 key table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3Md5Entry

swL3Md5Entry 1.3.6.1.4.1.171.11.119.4.3.4.1
A list of information displays the current MD5 key table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3Md5Entry  

swL3Md5KeyId 1.3.6.1.4.1.171.11.119.4.3.4.1.1
The MD5 key ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

swL3Md5Key 1.3.6.1.4.1.171.11.119.4.3.4.1.2
An MD5 password of up to 16 bytes.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..16)  

swL3Md5RowStatus 1.3.6.1.4.1.171.11.119.4.3.4.1.3
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3RouteRedistriTable 1.3.6.1.4.1.171.11.119.4.3.5
Route redistribution allows routers on the network that are running different routing protocols to exchange routing information. This is accomplished by comparing the routes stored in the varios routers' routing tables and assigning appropriate metrics. This information is then exchanged among the various routers according to the individual routers current routing protocol.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3RouteRedistriEntry

swL3RouteRedistriEntry 1.3.6.1.4.1.171.11.119.4.3.5.1
A list of information displaying the route redistribution table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3RouteRedistriEntry  

swL3RouteRedistriSrcProtocol 1.3.6.1.4.1.171.11.119.4.3.5.1.1
Allows the selection of the protocol of the source device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), rip(2), ospf(3), static(4), local(5), bgp(6)  

swL3RouteRedistriDstProtocol 1.3.6.1.4.1.171.11.119.4.3.5.1.2
Allows the selection of the protocol of the destination device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), rip(2), ospf(3), bgp(6)  

swL3RouteRedistriType 1.3.6.1.4.1.171.11.119.4.3.5.1.3
Allows the selection of one of the methods for calculating the metric value.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), all(2), type-1(3), type-2(4), internal(5), external(6), inter-E1(7), inter-E2(8), extType1(9), extType2(10)  

swL3RouteRedistriMetric 1.3.6.1.4.1.171.11.119.4.3.5.1.4
Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. The value '0' indicates default value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

swL3RouteRedistriRowStatus 1.3.6.1.4.1.171.11.119.4.3.5.1.5
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3RouteRedistriRouteMapName 1.3.6.1.4.1.171.11.119.4.3.5.1.6
This Object just works when the destination protocol is BGP and indicate the route-map working when redistribute the route to BGP.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..16)  

swL3OspfHostTable 1.3.6.1.4.1.171.11.119.4.3.6
The list of Hosts, and their metrics, that the router will advertise as host routes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3OspfHostEntry

swL3OspfHostEntry 1.3.6.1.4.1.171.11.119.4.3.6.1
A metric to be advertised, for a given type of service, when a given host is reachable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3OspfHostEntry  

swL3OspfHostIpAddress 1.3.6.1.4.1.171.11.119.4.3.6.1.1
The IP Address of the Host.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3OspfHostTOS 1.3.6.1.4.1.171.11.119.4.3.6.1.2
The Type of Service of the route being configured.
Status: current Access: read-only
OBJECT-TYPE    
  TOSType  

swL3OspfHostMetric 1.3.6.1.4.1.171.11.119.4.3.6.1.3
The Metric to be advertised.
Status: current Access: read-create
OBJECT-TYPE    
  Metric  

swL3OspfHostAreaID 1.3.6.1.4.1.171.11.119.4.3.6.1.4
The Area the Host Entry is to be found within. By default, the area that a subsuming OSPF interface is in, or 0.0.0.0
Status: current Access: read-create
OBJECT-TYPE    
  AreaID  

swL3OspfHostStatus 1.3.6.1.4.1.171.11.119.4.3.6.1.5
This variable displays the status of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3ospfVirtIfTable 1.3.6.1.4.1.171.11.119.4.3.7
Information about this router's virtual inter- faces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3OspfVirtIfEntry

swL3ospfVirtIfEntry 1.3.6.1.4.1.171.11.119.4.3.7.1
Information about a single Virtual Interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3OspfVirtIfEntry  

swL3ospfVirtIfAreaId 1.3.6.1.4.1.171.11.119.4.3.7.1.1
The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0
Status: current Access: read-only
OBJECT-TYPE    
  AreaID  

swL3ospfVirtIfNeighbor 1.3.6.1.4.1.171.11.119.4.3.7.1.2
The Router ID of the Virtual Neighbor.
Status: current Access: read-only
OBJECT-TYPE    
  RouterID  

swL3ospfVirtIfTransitDelay 1.3.6.1.4.1.171.11.119.4.3.7.1.3
The estimated number of seconds it takes to transmit a link- state update packet over this interface.
Status: current Access: read-only
OBJECT-TYPE    
  UpToMaxAge  

swL3ospfVirtIfRetransInterval 1.3.6.1.4.1.171.11.119.4.3.7.1.4
The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should be well over the expected round- trip time.
Status: current Access: read-only
OBJECT-TYPE    
  UpToMaxAge  

swL3ospfVirtIfHelloInterval 1.3.6.1.4.1.171.11.119.4.3.7.1.5
The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor.
Status: current Access: read-create
OBJECT-TYPE    
  HelloRange  

swL3ospfVirtIfRtrDeadInterval 1.3.6.1.4.1.171.11.119.4.3.7.1.6
The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

swL3ospfVirtIfState 1.3.6.1.4.1.171.11.119.4.3.7.1.7
OSPF virtual interface states.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(1), pointToPoint(4)  

swL3ospfVirtIfEvents 1.3.6.1.4.1.171.11.119.4.3.7.1.8
The number of state changes or error events on this Virtual Link
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swL3ospfVirtIfAuthType 1.3.6.1.4.1.171.11.119.4.3.7.1.9
The authentication type specified for a virtu- al interface. Additional authentication types may be assigned locally.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..255  

swL3ospfVirtIfAuthKey 1.3.6.1.4.1.171.11.119.4.3.7.1.10
If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

swL3ospfVirtIfAuthKeyID 1.3.6.1.4.1.171.11.119.4.3.7.1.11
The MD5 key ID.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..255  

swL3ospfVirtIfStatus 1.3.6.1.4.1.171.11.119.4.3.7.1.12
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3ospfIfTable 1.3.6.1.4.1.171.11.119.4.3.8
The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3OspfIfEntry

swL3ospfIfEntry 1.3.6.1.4.1.171.11.119.4.3.8.1
The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3OspfIfEntry  

swL3ospfIfIpAddress 1.3.6.1.4.1.171.11.119.4.3.8.1.1
The IP address of this OSPF interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3ospfAddressLessIf 1.3.6.1.4.1.171.11.119.4.3.8.1.2
For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swL3ospfIfAreaId 1.3.6.1.4.1.171.11.119.4.3.8.1.3
A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
Status: current Access: read-write
OBJECT-TYPE    
  AreaID  

swL3ospfIfType 1.3.6.1.4.1.171.11.119.4.3.8.1.4
The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25 and similar technologies take the value 'nbma', and links that are definitively point to point take the value 'pointToPoint'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER broadcast(1), nbma(2), pointToPoint(3), pointToMultipoint(5)  

swL3ospfIfAdminStat 1.3.6.1.4.1.171.11.119.4.3.8.1.5
The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.
Status: current Access: read-write
OBJECT-TYPE    
  Status  

swL3ospfIfRtrPriority 1.3.6.1.4.1.171.11.119.4.3.8.1.6
The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker.
Status: current Access: read-write
OBJECT-TYPE    
  DesignatedRouterPriority  

swL3ospfIfTransitDelay 1.3.6.1.4.1.171.11.119.4.3.8.1.7
The estimated number of seconds it takes to transmit a link state update packet over this interface.
Status: current Access: read-only
OBJECT-TYPE    
  UpToMaxAge  

swL3ospfIfRetransInterval 1.3.6.1.4.1.171.11.119.4.3.8.1.8
The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets.
Status: current Access: read-only
OBJECT-TYPE    
  UpToMaxAge  

swL3ospfIfHelloInterval 1.3.6.1.4.1.171.11.119.4.3.8.1.9
The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network.
Status: current Access: read-write
OBJECT-TYPE    
  HelloRange  

swL3ospfIfRtrDeadInterval 1.3.6.1.4.1.171.11.119.4.3.8.1.10
The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
Status: current Access: read-write
OBJECT-TYPE    
  PositiveInteger  

swL3ospfIfPollInterval 1.3.6.1.4.1.171.11.119.4.3.8.1.11
The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor.
Status: current Access: read-only
OBJECT-TYPE    
  PositiveInteger  

swL3ospfIfState 1.3.6.1.4.1.171.11.119.4.3.8.1.12
The OSPF Interface State.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(1), loopback(2), waiting(3), pointToPoint(4), designatedRouter(5), backupDesignatedRouter(6), otherDesignatedRouter(7)  

swL3ospfIfDesignatedRouter 1.3.6.1.4.1.171.11.119.4.3.8.1.13
The IP Address of the Designated Router.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3ospfIfBackupDesignatedRouter 1.3.6.1.4.1.171.11.119.4.3.8.1.14
The IP Address of the Backup Designated Router.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3ospfIfEvents 1.3.6.1.4.1.171.11.119.4.3.8.1.15
The number of times this OSPF interface has changed its state, or an error has occurred.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swL3ospfIfMulticastForwarding 1.3.6.1.4.1.171.11.119.4.3.8.1.16
The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting ospfMulticastForwarding to 0 effective- ly disables all multicast forwarding.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER blocked(1), multicast(2), unicast(3)  

swL3ospfIfDemand 1.3.6.1.4.1.171.11.119.4.3.8.1.17
Indicates whether Demand OSPF procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

swL3ospfIfAuthType 1.3.6.1.4.1.171.11.119.4.3.8.1.18
The authentication type specified for an in- terface. Additional authentication types may be assigned locally.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

swL3ospfIfAuthKey 1.3.6.1.4.1.171.11.119.4.3.8.1.19
The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfIfAuthKey always returns an Oc- tet String of length zero.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

swL3ospfIfAuthKeyID 1.3.6.1.4.1.171.11.119.4.3.8.1.20
The MD5 key ID.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

swL3ospfIfPassiveMode 1.3.6.1.4.1.171.11.119.4.3.8.1.21
Assign the designated entry to be a passive interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3ospfIfMetric 1.3.6.1.4.1.171.11.119.4.3.8.1.23
The Metric to be advertised.
Status: current Access: read-write
OBJECT-TYPE    
  Metric  

swL3ospfIfDistributeListInType 1.3.6.1.4.1.171.11.119.4.3.8.1.24
The type of route filter for distribute list in.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), access-list(2)  

swL3ospfIfDistributeListInName 1.3.6.1.4.1.171.11.119.4.3.8.1.25
The name of route filter for distribute list in.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

swL3RoutePreference 1.3.6.1.4.1.171.11.119.4.3.9
OBJECT IDENTIFIER    

swL3RoutePreferenceRIP 1.3.6.1.4.1.171.11.119.4.3.9.1
Used to configure the route preference of RIP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..999  

swL3RoutePreferenceOSPFIntra 1.3.6.1.4.1.171.11.119.4.3.9.2
Used to configure the route preference of OSPF Intra.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..999  

swL3RoutePreferenceStatic 1.3.6.1.4.1.171.11.119.4.3.9.3
Used to configure the route preference of Static.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..999  

swL3RoutePreferenceLocal 1.3.6.1.4.1.171.11.119.4.3.9.4
Used to read the route preference of Local.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..999  

swL3RoutePreferenceOSPFInter 1.3.6.1.4.1.171.11.119.4.3.9.5
Used to configure the route preference of OSPF Inter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..999  

swL3RoutePreferenceOSPFExtT1 1.3.6.1.4.1.171.11.119.4.3.9.6
Used to configure the route preference of OSPFExtT1.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..999  

swL3RoutePreferenceOSPFExtT2 1.3.6.1.4.1.171.11.119.4.3.9.7
Used to configure the route preference of OSPF ExtT2.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..999  

swL3RoutePreferenceDefault 1.3.6.1.4.1.171.11.119.4.3.9.8
Used to configure the route preference of Default route.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..999  

swL3ospfAreaTable 1.3.6.1.4.1.171.11.119.4.3.10
Information describing the configured parame- ters and cumulative statistics of the router's attached areas.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3ospfAreaEntry

swL3ospfAreaEntry 1.3.6.1.4.1.171.11.119.4.3.10.1
Information describing the configured parame- ters and cumulative statistics of one of the router's attached areas.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3ospfAreaEntry  

swL3ospfAreaId 1.3.6.1.4.1.171.11.119.4.3.10.1.1
A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.
Status: current Access: read-only
OBJECT-TYPE    
  AreaID  

swL3ospfAreaType 1.3.6.1.4.1.171.11.119.4.3.10.1.2
The type specified for an area.
Status: obsolete Access: read-create
OBJECT-TYPE    
  INTEGER normal(1), stub(2), nssa(3)  

swL3ospfAreaSummaryState 1.3.6.1.4.1.171.11.119.4.3.10.1.3
Whether the summary LSA is effective for this area.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), disabled(2), enabled(3)  

swL3ospfAreaMetric 1.3.6.1.4.1.171.11.119.4.3.10.1.4
Enter the metric (1 - 65535; 0 for auto cost) of this area.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

swL3ospfAreaTranslateState 1.3.6.1.4.1.171.11.119.4.3.10.1.5
.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), disabled(2), enabled(3)  

swL3ospfAreaStatus 1.3.6.1.4.1.171.11.119.4.3.10.1.6
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3dvmrpInterfaceTable 1.3.6.1.4.1.171.11.119.4.3.12
The (conceptual) table listing the router's multicast- capable interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3dvmrpInterfaceEntry

swL3dvmrpInterfaceEntry 1.3.6.1.4.1.171.11.119.4.3.12.1
An entry (conceptual row) in the dvmrpInterfaceTable. This row augments ipMRouteInterfaceEntry in the IP Multicast MIB, where the threshold object resides.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3dvmrpInterfaceEntry  

swL3dvmrpInterfaceIfIndex 1.3.6.1.4.1.171.11.119.4.3.12.1.1
The ifIndex value of the interface for which DVMRP is enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

swL3dvmrpInterfaceLocalAddress 1.3.6.1.4.1.171.11.119.4.3.12.1.2
The IP address this system will use as a source address on this interface. On unnumbered interfaces, it must be the same value as dvmrpInterfaceLocalAddress for some interface on the system.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

swL3dvmrpInterfaceMetric 1.3.6.1.4.1.171.11.119.4.3.12.1.3
The distance metric for this interface which is used to calculate distance vectors.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..31  

swL3dvmrpInterfaceProbe 1.3.6.1.4.1.171.11.119.4.3.12.1.4
Probe distribution interval.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

swL3dvmrpInterfaceNbrTimeout 1.3.6.1.4.1.171.11.119.4.3.12.1.5
Used to set the timer before neighbors are timed out.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

swL3dvmrpInterfaceStatus 1.3.6.1.4.1.171.11.119.4.3.12.1.6
The status of this entry. Creating the entry enables DVMRP on the virtual interface; destroying the entry or setting it to notInService disables DVMRP on the virtual interface.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3dvmrpInterfaceRcvBadPkts 1.3.6.1.4.1.171.11.119.4.3.12.1.7
The number of DVMRP packets received on the interface by the DVMRP process which were subsequently discarded as invalid (e.g. invalid packet format, or a route report from an unknown neighbor).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swL3dvmrpInterfaceRcvBadRoutes 1.3.6.1.4.1.171.11.119.4.3.12.1.8
The number of routes, in valid DVMRP packets, which were ignored because the entry was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swL3OspfInternalLsdbTable 1.3.6.1.4.1.171.11.119.4.3.13.1
The OSPF Process's Link State Database.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3OspfInternalLsdbEntry

swL3OspfInternalLsdbEntry 1.3.6.1.4.1.171.11.119.4.3.13.1.1
A single Link State Advertisement.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3OspfInternalLsdbEntry  

swL3OspfInternalLsdbAreaId 1.3.6.1.4.1.171.11.119.4.3.13.1.1.1
The 32 bit identifier of the Area from which the LSA was received.
Status: current Access: read-only
OBJECT-TYPE    
  AreaID  

swL3OspfInternalLsdbType 1.3.6.1.4.1.171.11.119.4.3.13.1.1.2
The type of the link state advertisement. Each link state type has a separate advertise- ment format.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER routerLink(1), networkLink(2), summaryLink(3), asSummaryLink(4), asExternalLink(5), multicastLink(6), nssaExternalLink(7)  

swL3OspfInternalLsdbLsid 1.3.6.1.4.1.171.11.119.4.3.13.1.1.3
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3OspfInternalLsdbRouterId 1.3.6.1.4.1.171.11.119.4.3.13.1.1.4
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
Status: current Access: read-only
OBJECT-TYPE    
  RouterID  

swL3OspfInternalLsdbMetric 1.3.6.1.4.1.171.11.119.4.3.13.1.1.5
Enter the metric (1 - 65535; 0 for auto cost) of this area.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

swL3OspfInternalLsdbSequenceNo 1.3.6.1.4.1.171.11.119.4.3.13.1.1.6
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

swL3OspfInternalLsdbAge 1.3.6.1.4.1.171.11.119.4.3.13.1.1.7
This field is the age of the link state adver- tisement in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

swL3OspfInternalLsdbChecksum 1.3.6.1.4.1.171.11.119.4.3.13.1.1.8
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swL3OspfExternalLsdbTable 1.3.6.1.4.1.171.11.119.4.3.13.2
The OSPF Process's Links State Database.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3OspfExternalLsdbEntry

swL3OspfExternalLsdbEntry 1.3.6.1.4.1.171.11.119.4.3.13.2.1
A single Link State Advertisement.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3OspfExternalLsdbEntry  

swL3OspfExternalLsdbType 1.3.6.1.4.1.171.11.119.4.3.13.2.1.1
The type of the link state advertisement. Each link state type has a separate advertise- ment format.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER asExternalLink(5), nssaExternalLink(7)  

swL3OspfExternalLsdbLsid 1.3.6.1.4.1.171.11.119.4.3.13.2.1.2
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3OspfExternalLsdbRouterId 1.3.6.1.4.1.171.11.119.4.3.13.2.1.3
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
Status: current Access: read-only
OBJECT-TYPE    
  RouterID  

swL3OspfExternalLsdbMetric 1.3.6.1.4.1.171.11.119.4.3.13.2.1.4
Enter the metric (1 - 65535; 0 for auto cost) of this area.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

swL3OspfExternalLsdbMetricType 1.3.6.1.4.1.171.11.119.4.3.13.2.1.5
Enter the metric type of this area.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unrecognized(0), type-1(1), type-2(2)  

swL3OspfExternalLsdbSequenceNo 1.3.6.1.4.1.171.11.119.4.3.13.2.1.6
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

swL3OspfExternalLsdbAge 1.3.6.1.4.1.171.11.119.4.3.13.2.1.7
This field is the age of the link state adver- tisement in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

swL3OspfExternalLsdbChecksum 1.3.6.1.4.1.171.11.119.4.3.13.2.1.8
This field is the checksum of the complete contents of the advertisement, except the age field. The age field is the exception so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swL3OspfExternalLsdbForwardingAddress 1.3.6.1.4.1.171.11.119.4.3.13.2.1.9
This field is the forwarding address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3OspfExternalLsdbRouteTag 1.3.6.1.4.1.171.11.119.4.3.13.2.1.10
This field is the route tag.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

swL3VrrpOperTable 1.3.6.1.4.1.171.11.119.4.3.14.1
Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of 'swL3vrrpOperEntry' items.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3VrrpOperEntry

swL3VrrpOperEntry 1.3.6.1.4.1.171.11.119.4.3.14.1.1
An entry in the vrrpOperTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combination of the IF index and VRID. Rows in the table cannot be modified unless the value of `swL3VrrpOperAdminState' is `disabled' and the `swL3VrrpOperState' has transitioned to `initialize'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3VrrpOperEntry  

swL3VrrpOperIfIndex 1.3.6.1.4.1.171.11.119.4.3.14.1.1.1
The ifIndex value of the interface for which VRRP is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swL3VrrpOperVrId 1.3.6.1.4.1.171.11.119.4.3.14.1.1.2
This object contains the Virtual Router Identifier (VRID).
Status: current Access: read-only
OBJECT-TYPE    
  VrId  

swL3VrrpOperVirtualMacAddr 1.3.6.1.4.1.171.11.119.4.3.14.1.1.3
The virtual MAC address of the virtual router. Although this object can be derived from the 'swL3VrrpOperVrId' object, it is defined so that it is easily obtainable by a management application and can be included in VRRP-related SNMP traps.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

swL3VrrpOperState 1.3.6.1.4.1.171.11.119.4.3.14.1.1.4
The current state of the virtual router. This object has three defined values: - `initialize', which indicates that all the virtual router is waiting for a startup event. - `backup', which indicates the virtual router is monitoring the availability of the master router. - `master', which indicates that the virtual router is forwarding packets for IP addresses that are associated with this router. Setting the `swL3VrrpOperAdminState' object (below) initiates transitions in the value of this object.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER initialize(1), backup(2), master(3)  

swL3VrrpOperAdminState 1.3.6.1.4.1.171.11.119.4.3.14.1.1.5
This object will enable/disable the virtual router function. Setting the value to `up', will transition the state of the virtual router from `initialize' to `backup' or `master', depending on the value of `swL3VrrpOperPriority'. Setting the value to `down', will transition the router from `master' or `backup' to `initialize'. State transitions may not be immediate; they sometimes depend on other factors, such as the interface (IF) state. The `swL3VrrpOperAdminState' object must be set to `down' prior to modifying the other read-create objects in the conceptual row. The value of the `swL3VrrpOperRowStatus' object (below) must be `active', signifying that the conceptual row is valid (i.e., the objects are correctly set), in order for this object to be set to `up'.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

swL3VrrpOperPriority 1.3.6.1.4.1.171.11.119.4.3.14.1.1.6
This object specifies the priority to be used for the virtual router master election process. Higher values imply higher priority. A priority of '0', although not settable, is sent by the master router to indicate that this router has ceased to participate in VRRP and a backup virtual router should transition to become a new master. A priority of 255 is used for the router that owns the associated IP address(es).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

swL3VrrpOperMasterIpAddr 1.3.6.1.4.1.171.11.119.4.3.14.1.1.7
The master router's real (primary) IP address. This is the IP address listed as the source in VRRP advertisement last received by this virtual router.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3VrrpOperCriticalIpAddr 1.3.6.1.4.1.171.11.119.4.3.14.1.1.8
In the case where there is more than one IP address for a given `ifIndex', this object is used to specify the IP address that will become the `swL3VrrpOperMasterIpAddr', should the virtual router transition from backup to master. If this object is set to 0.0.0.0, the IP address which is numerically lowest will be selected.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

swL3VrrpOperCheckCriticalIpState 1.3.6.1.4.1.171.11.119.4.3.14.1.1.9
Critical IP state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(0), disabled(1), enabled(2)  

swL3VrrpOperAuthType 1.3.6.1.4.1.171.11.119.4.3.14.1.1.10
Authentication type used for VRRP protocol exchanges between virtual routers. This value of this object is the same for a given ifIndex. New enumerations to this list can only be added via a new RFC on the standards track.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER noAuthentication(1), simpleTextPassword(2), ipAuthenticationHeader(3)  

swL3VrrpOperAuthKey 1.3.6.1.4.1.171.11.119.4.3.14.1.1.11
The Authentication Key. This object is set according to the value of the 'swL3VrrpOperAuthType' object ('simpleTextPassword' or 'ipAuthenticationHeader'). If the length of the value is less than 16 octets, the agent will left adjust and zero fill to 16 octets. The value of this object is the same for a given ifIndex. When read, swL3VrrpOperAuthKey always returns an Octet String of length zero.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

swL3VrrpOperAdvertisementInterval 1.3.6.1.4.1.171.11.119.4.3.14.1.1.12
The time interval, in seconds, between sending advertisement messages. Only the master router sends VRRP advertisements.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..255  

swL3VrrpOperPreemptMode 1.3.6.1.4.1.171.11.119.4.3.14.1.1.13
Controls whether a higher priority virtual router will preempt a lower priority master.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

swL3VrrpOperVirtualRouterUpTime 1.3.6.1.4.1.171.11.119.4.3.14.1.1.14
This is the value of the `sysUpTime' object when this virtual router (i.e., the `swL3VrrpOperState') transitioned out of `initialized'.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

swL3VrrpOperVirtualIpAddr 1.3.6.1.4.1.171.11.119.4.3.14.1.1.15
The assigned IP addresses that a virtual router is responsible for backing up.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

swL3VrrpOperRowStatus 1.3.6.1.4.1.171.11.119.4.3.14.1.1.16
The row status variable, used in accordance to installation and removal conventions for conceptual rows. The rowstatus of a currently active row in the vrrpOperTable is constrained by the operational state of the corresponding virtual router. When `vrrpOperRowStatus' is set to active(1), no other objects in the conceptual row, with the exception of `swL3VrrpOperAdminState', can be modified. Prior to setting the `swL3VrrpOperRowStatus' object from `active' to a different value, the `swL3VrrpOperAdminState' object must be set to `down' and the `vrrpOperState' object be transitioned to `initialize'. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the `vrrpOperRowStatus' column will be read as notReady(3). In particular, a newly created row cannot be made active(1) until (minimally) the corresponding instance of `swL3VrrpOperVrId' has been set and there is at least one active row in the `swL3VrrpAssoIpAddrTable' defining an associated IP address for the virtual router.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL3OspfECMPIpDestination 1.3.6.1.4.1.171.11.119.4.3.15.1
If set to 'enabled (1)', the ECMP algorithm will include the destination IP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3OspfECMPIpSource 1.3.6.1.4.1.171.11.119.4.3.15.2
If set to 'enabled (1)', the ECMP algorithm will include the lower 5 bits of the source IP. This attribution is mutually exclusive with crc_low and crc_high. If set to 'enabled (1)', crc_low and crc_high will be excluded.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3OspfECMPCrcLow 1.3.6.1.4.1.171.11.119.4.3.15.3
If set to 'enabled (1)', the ECMP algorithm will include the lower 5 bits of the CRC. This attribution is mutually exclusive with crc_high and ip_source. If set to 'enabled (1)', crc_high and ip_source will be excluded.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3OspfECMPCrcHigh 1.3.6.1.4.1.171.11.119.4.3.15.4
If set to 'enabled (1)', the ECMP algorithm will include the upper 5 bits of the CRC. This attribution is mutually exclusive with ip_source and crc_low. If set to 'enabled (1)', crc_low and ip_source will be excluded.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3OspfECMPTCPorUDPport 1.3.6.1.4.1.171.11.119.4.3.15.5
If set to 'enabled (1)', the ECMP algorithm will include the TCP or UDP port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3OspfECMPState 1.3.6.1.4.1.171.11.119.4.3.15.6
This object indicates the state of the OSPF ECMP function.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL3RIPUpdateTime 1.3.6.1.4.1.171.11.119.4.3.17.1
This object specifies the RIP update timer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 5..65535  

swL3RIPTimeOutTime 1.3.6.1.4.1.171.11.119.4.3.17.2
This object specifies the RIP time out timer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 5..65535  

swL3RIPGarbageCollectionTime 1.3.6.1.4.1.171.11.119.4.3.17.3
This object specifies the RIP garbage collection timer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 5..65535  

swL3OspfDefInfoOriginate 1.3.6.1.4.1.171.11.119.4.3.18.1
This object indicates if OSPF default external route is originated.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER always(1), default(2), none(3)  

swL3OspfDefInfoOrigMetricType 1.3.6.1.4.1.171.11.119.4.3.18.2
This object indicates the metric type of default external route originated by OSPF.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER type-1(1), type-2(2)  

swL3OspfDefInfoOrigMetric 1.3.6.1.4.1.171.11.119.4.3.18.3
This object indicates the metric of default external route originated by OSPF.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

swL3RIPInboundRouteFilterTable 1.3.6.1.4.1.171.11.119.4.3.19
The list of inbound route filter on RIP interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3RIPInboundRouteFilterEntry

swL3RIPInboundRouteFilterEntry 1.3.6.1.4.1.171.11.119.4.3.19.1
The information of inbound route filter on RIP interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3RIPInboundRouteFilterEntry  

swL3RIPInboundRouteFilterIfIpAddress 1.3.6.1.4.1.171.11.119.4.3.19.1.1
The IP Address of the RIP interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL3RIPInboundRouteFilterType 1.3.6.1.4.1.171.11.119.4.3.19.1.2
The type of inbound route filter for the RIP interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), access-list(2)  

swL3RIPInboundRouteFilterName 1.3.6.1.4.1.171.11.119.4.3.19.1.3
The name of inbound route filter for the RIP interface.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

swL3Route6RedistriTable 1.3.6.1.4.1.171.11.119.4.3.20
IPv6 Route redistribution allows routers on the network that are running different routing protocols to exchange routing information. This is accomplished by comparing the routes stored in the varios routers' routing tables and assigning appropriate metrics. This information is then exchanged among the various routers according to the individual routers current routing protocol.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3Route6RedistriEntry

swL3Route6RedistriEntry 1.3.6.1.4.1.171.11.119.4.3.20.1
A list of information displaying the IPv6 route redistribution table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL3Route6RedistriEntry  

swL3Route6RedistriSrcProtocol 1.3.6.1.4.1.171.11.119.4.3.20.1.1
Allows the selection of the protocol of the source device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER local(1), static(2), ripng(3), ospfv3(4)  

swL3Route6RedistriDstProtocol 1.3.6.1.4.1.171.11.119.4.3.20.1.2
Allows the selection of the protocol of the destination device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ripng(1), ospfv3(2)  

swL3Route6RedistriType 1.3.6.1.4.1.171.11.119.4.3.20.1.3
Allows the selection of one of the methods for calculating the metric value.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER type-1(1), type-2(2), all(3)  

swL3Route6RedistriMetric 1.3.6.1.4.1.171.11.119.4.3.20.1.4
Allows the entry of an OSPFv3 interface cost. This is analogous to a Hop Count in the RIPng routing protocol. The value '0' indicates default value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

swL3Route6RedistriRowStatus 1.3.6.1.4.1.171.11.119.4.3.20.1.5
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus