DES3016-L2MGMT-MIB

File: DES3016-L2MGMT-MIB.mib (137387 bytes)

Imported modules

SNMPv2-TC SNMPv2-SMI RFC1155-SMI
RFC1213-MIB SWPRIMGMT-MIB

Imported symbols

TEXTUAL-CONVENTION MODULE-IDENTITY OBJECT-TYPE
Unsigned32 Integer32 IpAddress
RowStatus TruthValue DisplayString
des3016

Defined Types

VlanId  
INTEGER 1..4094    

PortList  
OCTET STRING Size(0..127)    

MacAddress  
OCTET STRING Size(6)    

SwL2PortInfoEntry  
SEQUENCE    
  swL2PortInfoPortIndex INTEGER
  swL2PortInfoLinkStatus INTEGER
  swL2PortInfoNwayStatus INTEGER

SwL2PortCtrlEntry  
SEQUENCE    
  swL2PortCtrlPortIndex INTEGER
  swL2PortCtrlAdminState INTEGER
  swL2PortCtrlNwayState INTEGER
  swL2PortCtrlFlowCtrlState INTEGER
  swL2PortCtrlDescription DisplayString
  swL2PortCtrlMACNotifyState INTEGER
  swL2PortCtrlMDIXState INTEGER

SwL2PortErrEntry  
SEQUENCE    
  swL2PortErrPortIndex INTEGER
  swL2PortErrPortState INTEGER
  swL2PortErrPortStatus INTEGER
  swL2PortErrPortReason INTEGER
  swL2PortErrDescription DisplayString

SwL2QOSBandwidthControlEntry  
SEQUENCE    
  swL2QOSBandwidthPortIndex INTEGER
  swL2QOSBandwidthRxRate INTEGER
  swL2QOSBandwidthTxRate INTEGER
  swL2QOSBandwidthRadiusRxRate INTEGER
  swL2QOSBandwidthRadiusTxRate INTEGER

SwL2QOSSchedulingEntry  
SEQUENCE    
  swL2QOSSchedulingClassIndex INTEGER
  swL2QOSSchedulingMaxWeight INTEGER

SwL2QOS8021pUserPriorityEntry  
SEQUENCE    
  swL2QOS8021pUserPriorityIndex INTEGER
  swL2QOS8021pUserPriorityClass INTEGER

SwL2QOS8021pDefaultPriorityEntry  
SEQUENCE    
  swL2QOS8021pDefaultPriorityIndex INTEGER
  swL2QOS8021pDefaultPriority INTEGER
  swL2QOS8021pRadiusPriority INTEGER

SwPortTrunkEntry  
SEQUENCE    
  swPortTrunkIndex Integer32
  swPortTrunkMasterPort Integer32
  swPortTrunkPortList PortList
  swPortTrunkType INTEGER
  swPortTrunkActivePort PortList
  swPortTrunkState RowStatus
  swPortTrunkFloodingPort Integer32

SwL2TrunkLACPPortEntry  
SEQUENCE    
  swL2TrunkLACPPortIndex INTEGER
  swL2TrunkLACPPortState INTEGER

SwL2TrunkVLANEntry  
SEQUENCE    
  swL2TrunkVLANPort INTEGER
  swL2TrunkVLANState INTEGER

SwL2IGMPCtrlEntry  
SEQUENCE    
  swL2IGMPCtrlVid INTEGER
  swL2IGMPQueryInterval INTEGER
  swL2IGMPMaxResponseTime INTEGER
  swL2IGMPRobustness INTEGER
  swL2IGMPLastMemberQueryInterval INTEGER
  swL2IGMPHostTimeout INTEGER
  swL2IGMPRouteTimeout INTEGER
  swL2IGMPLeaveTimer INTEGER
  swL2IGMPQueryState INTEGER
  swL2IGMPCurrentState INTEGER
  swL2IGMPCtrlState INTEGER
  swL2IGMPFastLeave INTEGER

SwL2IGMPQueryInfoEntry  
SEQUENCE    
  swL2IGMPInfoVid INTEGER
  swL2IGMPInfoQueryCount INTEGER
  swL2IGMPInfoTxQueryCount INTEGER

SwL2IGMPInfoEntry  
SEQUENCE    
  swL2IGMPVid INTEGER
  swL2IGMPGroupIpAddr IpAddress
  swL2IGMPMacAddr MacAddress
  swL2IGMPPortMap PortList
  swL2IGMPIpGroupReportCount INTEGER

SwL2IGMPRouterPortEntry  
SEQUENCE    
  swL2IGMPRouterPortVlanid INTEGER
  swL2IGMPRouterPortVlanName DisplayString
  swL2IGMPRouterPortStaticPortList PortList
  swL2IGMPRouterPortDynamicPortList PortList
  swL2IGMPRouterPortForbiddenPortList PortList

SwL2IGMPAccessAuthEntry  
SEQUENCE    
  swL2IGMPAccessAuthPort INTEGER
  swL2IGMPAccessAuthState INTEGER

SwL2TrafficCtrlEntry  
SEQUENCE    
  swL2TrafficCtrlGroupIndex INTEGER
  swL2TrafficCtrlUnitIndex INTEGER
  swL2TrafficCtrlBMStromthreshold INTEGER
  swL2TrafficCtrlBcastStromCtrl INTEGER
  swL2TrafficCtrlMcastStromCtrl INTEGER
  swL2TrafficCtrlUcastStromCtrl INTEGER

SwL2TrafficSegEntry  
SEQUENCE    
  swL2TrafficSegPort INTEGER
  swL2TrafficSegForwardPorts PortList

SwL2PortSecurityControlEntry  
SEQUENCE    
  swL2PortSecurityPortIndex INTEGER
  swL2PortSecurityMaxLernAddr INTEGER
  swL2PortSecurityMode INTEGER
  swL2PortSecurityAdmState INTEGER
  swL2PortSecurityEntryClearCtrl INTEGER

SwL2StpPortEntry  
SEQUENCE    
  swL2StpPort INTEGER
  swL2StpPortStatus INTEGER
  swL2StpPortRole INTEGER
  swL2StpPortFBPDU INTEGER
  swL2StpPortLinkState INTEGER
  swL2StpPortProtocolMigration TruthValue
  swL2StpPortAdminEdgePort INTEGER
  swL2StpPortOperEdgePort TruthValue
  swL2StpPortAdminPointToPoint INTEGER
  swL2StpPortOperPointToPoint TruthValue
  swL2StpPortAdminPathCost Unsigned32
  swL2StpPortPriority INTEGER
  swL2STPPortState INTEGER
  swL2StpPortRestrictedRole TruthValue
  swL2StpPortRestrictedTCN TruthValue

SwL2CosPriorityEntry  
SEQUENCE    
  swL2CosPriorityPort INTEGER
  swL2CosPriorityPortPRI INTEGER
  swL2CosPriorityEtherPRI INTEGER
  swL2CosPriorityIpPRI INTEGER
  swL2CosPriorityNone INTEGER

SwL2CosPortPRIEntry  
SEQUENCE    
  swL2CosPortPRIIndex INTEGER
  swL2CosPortPRIClass INTEGER

SwL2CosMacBasePRIEntry  
SEQUENCE    
  swL2CosMacBasePRIIndex MacAddress
  swL2CosMacBasePRIClass INTEGER

SwL2CosTosPRIEntry  
SEQUENCE    
  swL2CosTosPRIIndex INTEGER
  swL2CosTosPRIClass INTEGER

SwL2CosDscpPRIEntry  
SEQUENCE    
  swL2CosDscpPRIIndex INTEGER
  swL2CosDscpPRIClass INTEGER

SwL2LoopDetectPortEntry  
SEQUENCE    
  swL2LoopDetectPortIndex INTEGER
  swL2LoopDetectPortState INTEGER
  swL2LoopDetectPortLoopStatus INTEGER

SwL2VlanEntry  
SEQUENCE    
  swL2VlanIndex VlanId
  swL2VlanName DisplayString
  swL2VlanType INTEGER
  swL2VlanMemberPorts PortList
  swL2VlanStaticPorts PortList
  swL2VlanUntaggedPorts PortList
  swL2VlanTaggedPorts PortList

Defined Values

swL2MgmtMIB 1.3.6.1.4.1.171.11.63.10.2
The Structure of Common Management Information for making a trunk and IGMP related function for D-Link devices.
MODULE-IDENTITY    

swL2DevMgmt 1.3.6.1.4.1.171.11.63.10.2.1
OBJECT IDENTIFIER    

swL2PortMgmt 1.3.6.1.4.1.171.11.63.10.2.2
OBJECT IDENTIFIER    

swL2QOSMgmt 1.3.6.1.4.1.171.11.63.10.2.3
OBJECT IDENTIFIER    

swL2TrunkMgmt 1.3.6.1.4.1.171.11.63.10.2.4
OBJECT IDENTIFIER    

swPortMirrorPackage 1.3.6.1.4.1.171.11.63.10.2.6
OBJECT IDENTIFIER    

swIGMPPackage 1.3.6.1.4.1.171.11.63.10.2.7
OBJECT IDENTIFIER    

swL2TrafficMgmt 1.3.6.1.4.1.171.11.63.10.2.11
OBJECT IDENTIFIER    

swL2TrafficSegMgmt 1.3.6.1.4.1.171.11.63.10.2.12
OBJECT IDENTIFIER    

swL2PortSecurityMgmt 1.3.6.1.4.1.171.11.63.10.2.15
OBJECT IDENTIFIER    

swL2StpMgmt 1.3.6.1.4.1.171.11.63.10.2.16
OBJECT IDENTIFIER    

swL2CosMgmt 1.3.6.1.4.1.171.11.63.10.2.17
OBJECT IDENTIFIER    

swL2LoopDetectMgmt 1.3.6.1.4.1.171.11.63.10.2.18
OBJECT IDENTIFIER    

swL2VLANMgmt 1.3.6.1.4.1.171.11.63.10.2.19
OBJECT IDENTIFIER    

swL2MgmtMIBTraps 1.3.6.1.4.1.171.11.63.10.2.100
OBJECT IDENTIFIER    

swL2DevInfo 1.3.6.1.4.1.171.11.63.10.2.1.1
OBJECT IDENTIFIER    

swL2DevInfoFrontPanelLedStatus 1.3.6.1.4.1.171.11.63.10.2.1.1.5
This object is a set of system LED indications. The two octets is defined as system LED. The first LED is power LED. The second LED is console LED. The other octets following the second octets are the logical port LED (following dot1dBasePort ordering). Every two bytes are presented to a port. The first byte is presentd to the Link/Activity LED. The second byte is presented to the Speed LED. Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..127)  

swL2CPUutilization 1.3.6.1.4.1.171.11.63.10.2.1.3
OBJECT IDENTIFIER    

swL2CPUutilizationIn5sec 1.3.6.1.4.1.171.11.63.10.2.1.3.1
Time scale is 5 seconds.The value will be between 0%(idle) and 100% (very busy).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swL2CPUutilizationIn1min 1.3.6.1.4.1.171.11.63.10.2.1.3.2
Time scale is 1 minute.The value will be between 0%(idle) and 100% (very busy).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swL2CPUutilizationIn5min 1.3.6.1.4.1.171.11.63.10.2.1.3.3
Time scale is 5 minute.The value will be between 0%(idle) and 100% (very busy).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swL2DevAlarm 1.3.6.1.4.1.171.11.63.10.2.1.4
OBJECT IDENTIFIER    

swL2DevAlarmLinkChange 1.3.6.1.4.1.171.11.63.10.2.1.4.3
This object determines whether or not to send a trap message when the link changes. If the object is enabled (3), the Link Change trap is sent by the device when any of its port links change. The device does not send the trap if this object value is disabled or in another state.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrl 1.3.6.1.4.1.171.11.63.10.2.1.2
OBJECT IDENTIFIER    

swL2DevCtrlSystemReboot 1.3.6.1.4.1.171.11.63.10.2.1.2.1
This object indicates the agent system reboot state. The agent always returns other(1) when this object is read.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), reboot(2), save-config-and-reboot(3), reboot-and-load-factory-default-config(4)  

swL2DevCtrlSystemIP 1.3.6.1.4.1.171.11.63.10.2.1.2.2
This object indicates system ip.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2DevCtrlSubnetMask 1.3.6.1.4.1.171.11.63.10.2.1.2.3
This object indicates system subnet mask.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2DevCtrlDefaultGateway 1.3.6.1.4.1.171.11.63.10.2.1.2.4
This object indicates system default gateway.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2DevCtrlManagementVlanId 1.3.6.1.4.1.171.11.63.10.2.1.2.5
This object controls which Vlan includes system ip. And the Vlan should have been created.
Status: current Access: read-write
OBJECT-TYPE    
  VlanId  

swL2DevCtrlStpState 1.3.6.1.4.1.171.11.63.10.2.1.2.6
This object can be enabled or disabled spanning tree algorithm during runtime of the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlIGMPSnooping 1.3.6.1.4.1.171.11.63.10.2.1.2.7
This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlCleanAllStatisticCounter 1.3.6.1.4.1.171.11.63.10.2.1.2.12
As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), active(2)  

swL2DevCtrlSnmpEnableAuthenTraps 1.3.6.1.4.1.171.11.63.10.2.1.2.13
Indicates whether the SNMP entity is permitted to generate authenticationFailure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authenticationFailure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant across re-initializations of the network management system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL2DevCtrlRmonState 1.3.6.1.4.1.171.11.63.10.2.1.2.16
This object can be enabled or disabled RMON.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlIpAutoConfig 1.3.6.1.4.1.171.11.63.10.2.1.2.17
Indicates the status of automatically getting configuration from TFTP server on device
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlMulticastfilter 1.3.6.1.4.1.171.11.63.10.2.1.2.18
This object decide the multicast packets filtering mode on all port .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER forward-unregistered-groups(2), filter-unregistered-groups(3)  

swL2MACNotifyState 1.3.6.1.4.1.171.11.63.10.2.1.2.19
This object can enabled or disabled MAC Notification.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2MACNotifyHistorySize 1.3.6.1.4.1.171.11.63.10.2.1.2.20
This object indicates the history size of variation MAC in address table. The default value is 1 .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..500  

swL2MACNotifyInterval 1.3.6.1.4.1.171.11.63.10.2.1.2.21
This object indicates the time interval in second for trigger the MAC notify message.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

swL2DevCtrlVLANTrunkState 1.3.6.1.4.1.171.11.63.10.2.1.2.22
This indicates the global state of the VLAN trunking feature of the device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL2DevCtrlLLDPState 1.3.6.1.4.1.171.11.63.10.2.1.2.23
Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For receiving LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL2DevCtrlLLDPForwardMessageState 1.3.6.1.4.1.171.11.63.10.2.1.2.24
When lldp is disabled and lldp forward_message's are enabled, the LLDP Data Unit packets received by the switch will be forwarded.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL2DevCtrlVlanIdOfFDBTbl 1.3.6.1.4.1.171.11.63.10.2.1.2.25
Indicates the VLAN ID to which the Dot1dTpFdbTable belongs; The default value is DEFAULT_VLAN_ID of the system.
Status: current Access: read-write
OBJECT-TYPE    
  VlanId  

swL2PortInfoTable 1.3.6.1.4.1.171.11.63.10.2.2.1
A table that contains information about every port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortInfoEntry

swL2PortInfoEntry 1.3.6.1.4.1.171.11.63.10.2.2.1.1
A list of information for each port of the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2PortInfoEntry  

swL2PortInfoPortIndex 1.3.6.1.4.1.171.11.63.10.2.2.1.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

swL2PortInfoLinkStatus 1.3.6.1.4.1.171.11.63.10.2.2.1.1.4
This object indicates the port link status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), link-pass(2), link-fail(3)  

swL2PortInfoNwayStatus 1.3.6.1.4.1.171.11.63.10.2.2.1.1.5
This object indicates the port speed and duplex mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER auto(1), full-10Mbps-8023x(2), full-10Mbps-none(3), half-10Mbps-backp(4), half-10Mbps-none(5), full-100Mbps-8023x(6), full-100Mbps-none(7), half-100Mbps-backp(8), half-100Mbps-none(9), full-1Gigabps-8023x(10), full-1Gigabps-none(11), half-1Gigabps-backp(12), half-1Gigabps-none(13)  

swL2PortCtrlTable 1.3.6.1.4.1.171.11.63.10.2.2.2
A table that contains control information about every port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortCtrlEntry

swL2PortCtrlEntry 1.3.6.1.4.1.171.11.63.10.2.2.2.1
A list of control information for each port of the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2PortCtrlEntry  

swL2PortCtrlPortIndex 1.3.6.1.4.1.171.11.63.10.2.2.2.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

swL2PortCtrlAdminState 1.3.6.1.4.1.171.11.63.10.2.2.2.1.2
This object decide the port enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlNwayState 1.3.6.1.4.1.171.11.63.10.2.2.2.1.3
Chose the port speed, duplex mode, and N-Way function mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nway-auto(1), nway-disabled-10Mbps-Half(2), nway-disabled-10Mbps-Full(3), nway-disabled-100Mbps-Half(4), nway-disabled-100Mbps-Full(5), nway-disabled-1Gigabps-Full(7)  

swL2PortCtrlFlowCtrlState 1.3.6.1.4.1.171.11.63.10.2.2.2.1.4
Set flow control function as enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlDescription 1.3.6.1.4.1.171.11.63.10.2.2.2.1.5
The object describe the ports in text.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

swL2PortCtrlMACNotifyState 1.3.6.1.4.1.171.11.63.10.2.2.2.1.7
This object set each poet MAC notification state.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlMDIXState 1.3.6.1.4.1.171.11.63.10.2.2.2.1.10
This object controls the MDIX state of a specified port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), normal(2), cross(3)  

swL2PortErrTable 1.3.6.1.4.1.171.11.63.10.2.2.3
A table that contains information about Err port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortErrEntry

swL2PortErrEntry 1.3.6.1.4.1.171.11.63.10.2.2.3.1
A list of information for err port of the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2PortErrEntry  

swL2PortErrPortIndex 1.3.6.1.4.1.171.11.63.10.2.2.3.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

swL2PortErrPortState 1.3.6.1.4.1.171.11.63.10.2.2.3.1.2
This object decide the portstate enabled or disabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

swL2PortErrPortStatus 1.3.6.1.4.1.171.11.63.10.2.2.3.1.3
This object decide the PortStatus whether err-disabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), err-disabled(2)  

swL2PortErrPortReason 1.3.6.1.4.1.171.11.63.10.2.2.3.1.4
This object decide the PortStatus STP LBD or Storm control.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER stp-lbd(1), storm-control(2)  

swL2PortErrDescription 1.3.6.1.4.1.171.11.63.10.2.2.3.1.5
The object describe the ports in text.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

swL2QOSBandwidthControlTable 1.3.6.1.4.1.171.11.63.10.2.3.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOSBandwidthControlEntry

swL2QOSBandwidthControlEntry 1.3.6.1.4.1.171.11.63.10.2.3.1.1
A list of information contained in swL2QOSBandwidthControlTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2QOSBandwidthControlEntry  

swL2QOSBandwidthPortIndex 1.3.6.1.4.1.171.11.63.10.2.3.1.1.1
Indicates the port .
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..650  

swL2QOSBandwidthRxRate 1.3.6.1.4.1.171.11.63.10.2.3.1.1.2
Indicates RX Rate(Mbit/sec) of the specifed port.Value 1024000 means no limit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 64..1024000  

swL2QOSBandwidthTxRate 1.3.6.1.4.1.171.11.63.10.2.3.1.1.3
Indicates TX Rate(Mbit/sec) of the specifed port.Value 1024000 means no limit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 64..1024000  

swL2QOSBandwidthRadiusRxRate 1.3.6.1.4.1.171.11.63.10.2.3.1.1.4
The RxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured RxRate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2QOSBandwidthRadiusTxRate 1.3.6.1.4.1.171.11.63.10.2.3.1.1.5
The TxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured TxRate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2QOSSchedulingTable 1.3.6.1.4.1.171.11.63.10.2.3.2
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOSSchedulingEntry

swL2QOSSchedulingEntry 1.3.6.1.4.1.171.11.63.10.2.3.2.1
A list of information contained in swL2QOSSchedulingTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2QOSSchedulingEntry  

swL2QOSSchedulingClassIndex 1.3.6.1.4.1.171.11.63.10.2.3.2.1.1
Indicates the hardware queue number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..3  

swL2QOSSchedulingMaxWeight 1.3.6.1.4.1.171.11.63.10.2.3.2.1.4
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..55  

swL2QOSSchedulingMechanismCtrl 1.3.6.1.4.1.171.11.63.10.2.3.5
This object can control QOS scheduling Mechanism.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER strict(1), weightfair(2), none(3)  

swL2QOS8021pUserPriorityTable 1.3.6.1.4.1.171.11.63.10.2.3.3
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOS8021pUserPriorityEntry

swL2QOS8021pUserPriorityEntry 1.3.6.1.4.1.171.11.63.10.2.3.3.1
A list of information contained in swL2QOS8021pUserPriorityTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2QOS8021pUserPriorityEntry  

swL2QOS8021pUserPriorityIndex 1.3.6.1.4.1.171.11.63.10.2.3.3.1.1
The 802.1p user priority .
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

swL2QOS8021pUserPriorityClass 1.3.6.1.4.1.171.11.63.10.2.3.3.1.2
The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..3  

swL2QOS8021pDefaultPriorityTable 1.3.6.1.4.1.171.11.63.10.2.3.4
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOS8021pDefaultPriorityEntry

swL2QOS8021pDefaultPriorityEntry 1.3.6.1.4.1.171.11.63.10.2.3.4.1
A list of information contained in swL2QOS8021pDefaultPriorityTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2QOS8021pDefaultPriorityEntry  

swL2QOS8021pDefaultPriorityIndex 1.3.6.1.4.1.171.11.63.10.2.3.4.1.1
Indicates the port number .
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..650  

swL2QOS8021pDefaultPriority 1.3.6.1.4.1.171.11.63.10.2.3.4.1.2
The priority value to assign to untagged packets received by the switch ports on the switch..
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

swL2QOS8021pRadiusPriority 1.3.6.1.4.1.171.11.63.10.2.3.4.1.3
The value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swPortTrunkMaxEntries 1.3.6.1.4.1.171.11.63.10.2.4.1
The max entries of swPortTrunkTable
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swPortTrunkMaxPortMembers 1.3.6.1.4.1.171.11.63.10.2.4.2
The max number of ports allowed in a trunk.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swPortTrunkTable 1.3.6.1.4.1.171.11.63.10.2.4.3
This table specifies the port membership for each logical link.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwPortTrunkEntry

swPortTrunkEntry 1.3.6.1.4.1.171.11.63.10.2.4.3.1
A list of information specifies which ports group form a single logical link.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwPortTrunkEntry  

swPortTrunkIndex 1.3.6.1.4.1.171.11.63.10.2.4.3.1.1
The index of logical port trunk.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

swPortTrunkMasterPort 1.3.6.1.4.1.171.11.63.10.2.4.3.1.2
The object indicates the master port number of the port trunk entry.The first port of the trunk is implicitly configured to be the master logical port.When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

swPortTrunkPortList 1.3.6.1.4.1.171.11.63.10.2.4.3.1.3
Indicate member ports of a logical trunk.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

swPortTrunkType 1.3.6.1.4.1.171.11.63.10.2.4.3.1.4
This object indicates the type of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER static(1), lacp(2)  

swPortTrunkActivePort 1.3.6.1.4.1.171.11.63.10.2.4.3.1.5
This object indicates the active ports of this entry.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swPortTrunkState 1.3.6.1.4.1.171.11.63.10.2.4.3.1.6
This object indicates the status of this entry. when the state is CreatAndGo(4),the type of trunk is static(1); when the state is CreatAndWait(5),the type of trunk is lacp(2).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swPortTrunkFloodingPort 1.3.6.1.4.1.171.11.63.10.2.4.3.1.7
The flooding port of every trunk.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swL2TrunkAlgorithm 1.3.6.1.4.1.171.11.63.10.2.4.4
This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), mac-source(2), mac-destination(3), mac-source-dest(4)  

swL2TrunkLACPPortTable 1.3.6.1.4.1.171.11.63.10.2.4.5
This table specifys which ports group a set of ports(up to 8) into a single logical link.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrunkLACPPortEntry

swL2TrunkLACPPortEntry 1.3.6.1.4.1.171.11.63.10.2.4.5.1
A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2TrunkLACPPortEntry  

swL2TrunkLACPPortIndex 1.3.6.1.4.1.171.11.63.10.2.4.5.1.1
The index of logical port lacp.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkLACPPortState 1.3.6.1.4.1.171.11.63.10.2.4.5.1.2
The state of logical port lacp.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER active(1), passive(2)  

swL2TrunkVLANTable 1.3.6.1.4.1.171.11.63.10.2.4.6
This table is used to manage the VLAN trunking feature of the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrunkVLANEntry

swL2TrunkVLANEntry 1.3.6.1.4.1.171.11.63.10.2.4.6.1
This object is used to configure the VLAN trunking settings for each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2TrunkVLANEntry  

swL2TrunkVLANPort 1.3.6.1.4.1.171.11.63.10.2.4.6.1.1
This object indicates the port being configured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkVLANState 1.3.6.1.4.1.171.11.63.10.2.4.6.1.2
The state of the logical port LACP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swPortMirrorRxPortList 1.3.6.1.4.1.171.11.63.10.2.6.2
This object indicates the Rx port list of ports to be sniffed.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swPortMirrorTxPortList 1.3.6.1.4.1.171.11.63.10.2.6.3
This object indicates the Tx port list of ports to be sniffed.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swPortMirrorTargetPort 1.3.6.1.4.1.171.11.63.10.2.6.4
This object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

swPortMirrorState 1.3.6.1.4.1.171.11.63.10.2.6.5
This object indicates the status of this entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2IGMPMaxSupportedVlans 1.3.6.1.4.1.171.11.63.10.2.7.1
Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPCtrlTable).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPMaxIpGroupNumPerVlan 1.3.6.1.4.1.171.11.63.10.2.7.2
Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPQueryInfoTable).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPCtrlTable 1.3.6.1.4.1.171.11.63.10.2.7.3
The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with index range from 1 to 12.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPCtrlEntry

swL2IGMPCtrlEntry 1.3.6.1.4.1.171.11.63.10.2.7.3.1
The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPCtrlEntry  

swL2IGMPCtrlVid 1.3.6.1.4.1.171.11.63.10.2.7.3.1.1
This object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPQueryInterval 1.3.6.1.4.1.171.11.63.10.2.7.3.1.2
The frequency at which IGMP Host-Query packets are transmitted on this switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

swL2IGMPMaxResponseTime 1.3.6.1.4.1.171.11.63.10.2.7.3.1.3
The maximum query response time on this switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..25  

swL2IGMPRobustness 1.3.6.1.4.1.171.11.63.10.2.7.3.1.4
The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

swL2IGMPLastMemberQueryInterval 1.3.6.1.4.1.171.11.63.10.2.7.3.1.5
The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

swL2IGMPHostTimeout 1.3.6.1.4.1.171.11.63.10.2.7.3.1.6
The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPRouteTimeout 1.3.6.1.4.1.171.11.63.10.2.7.3.1.7
The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPLeaveTimer 1.3.6.1.4.1.171.11.63.10.2.7.3.1.8
When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPQueryState 1.3.6.1.4.1.171.11.63.10.2.7.3.1.9
This object decide the IGMP query enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2IGMPCurrentState 1.3.6.1.4.1.171.11.63.10.2.7.3.1.10
This object indicates the current IGMP query state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), querier(2), non-querier(3)  

swL2IGMPCtrlState 1.3.6.1.4.1.171.11.63.10.2.7.3.1.11
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - IGMP funtion is enabled for this entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

swL2IGMPFastLeave 1.3.6.1.4.1.171.11.63.10.2.7.3.1.12
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

swL2IGMPQueryInfoTable 1.3.6.1.4.1.171.11.63.10.2.7.4
The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPQueryInfoEntry

swL2IGMPQueryInfoEntry 1.3.6.1.4.1.171.11.63.10.2.7.4.1
Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPQueryInfoEntry  

swL2IGMPInfoVid 1.3.6.1.4.1.171.11.63.10.2.7.4.1.1
This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoQueryCount 1.3.6.1.4.1.171.11.63.10.2.7.4.1.2
This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoTxQueryCount 1.3.6.1.4.1.171.11.63.10.2.7.4.1.3
This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoTable 1.3.6.1.4.1.171.11.63.10.2.7.5
The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPInfoEntry

swL2IGMPInfoEntry 1.3.6.1.4.1.171.11.63.10.2.7.5.1
Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPInfoEntry  

swL2IGMPVid 1.3.6.1.4.1.171.11.63.10.2.7.5.1.1
This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPGroupIpAddr 1.3.6.1.4.1.171.11.63.10.2.7.5.1.2
This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL2IGMPMacAddr 1.3.6.1.4.1.171.11.63.10.2.7.5.1.3
This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

swL2IGMPPortMap 1.3.6.1.4.1.171.11.63.10.2.7.5.1.4
This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swL2IGMPIpGroupReportCount 1.3.6.1.4.1.171.11.63.10.2.7.5.1.5
This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPRouterPortTable 1.3.6.1.4.1.171.11.63.10.2.7.6
The information of the router port table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPRouterPortEntry

swL2IGMPRouterPortEntry 1.3.6.1.4.1.171.11.63.10.2.7.6.1
The entry of swL2IGMPRouterPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPRouterPortEntry  

swL2IGMPRouterPortVlanid 1.3.6.1.4.1.171.11.63.10.2.7.6.1.1
This object indicates the VLAN ID of the router port entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4094  

swL2IGMPRouterPortVlanName 1.3.6.1.4.1.171.11.63.10.2.7.6.1.2
This object indicates the VLAN name of the router port entry.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

swL2IGMPRouterPortStaticPortList 1.3.6.1.4.1.171.11.63.10.2.7.6.1.3
This object indicates the static portlist of the router port entry.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swL2IGMPRouterPortDynamicPortList 1.3.6.1.4.1.171.11.63.10.2.7.6.1.4
This object indicates the dynamic portlist of the router port entry.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swL2IGMPRouterPortForbiddenPortList 1.3.6.1.4.1.171.11.63.10.2.7.6.1.5
This object indicate the forbidden portlist of the router port entry.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swL2IGMPAccessAuthTable 1.3.6.1.4.1.171.11.63.10.2.7.7
This table is used to manage the IGMP Access Authentication configurations of the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPAccessAuthEntry

swL2IGMPAccessAuthEntry 1.3.6.1.4.1.171.11.63.10.2.7.7.1
A list of manageable entities for IGMP Access Authentication. The configuration is done per port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPAccessAuthEntry  

swL2IGMPAccessAuthPort 1.3.6.1.4.1.171.11.63.10.2.7.7.1.1
The index of the swL2IGMPAccessAuthTable. This object corresponds to the port being configured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPAccessAuthState 1.3.6.1.4.1.171.11.63.10.2.7.7.1.2
This object denotes the status of IGMP Access Authentication of the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

swL2TrafficCtrlTable 1.3.6.1.4.1.171.11.63.10.2.11.1
This table specifys the storm traffic control configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrafficCtrlEntry

swL2TrafficCtrlEntry 1.3.6.1.4.1.171.11.63.10.2.11.1.1
A list of information specifies the storm traffic control configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2TrafficCtrlEntry  

swL2TrafficCtrlGroupIndex 1.3.6.1.4.1.171.11.63.10.2.11.1.1.1
The index of logical port trunk. The trunk group number depend on the existence of unit and module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrafficCtrlUnitIndex 1.3.6.1.4.1.171.11.63.10.2.11.1.1.2
Indicates ID of the unit in the device
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrafficCtrlBMStromthreshold 1.3.6.1.4.1.171.11.63.10.2.11.1.1.3
This object to decide how much thousand packets per second broadcast/multicast (depend on swL2TrafficCtrlBcastStromCtrl, swL2TrafficCtrlMcastStromCtrl or swL2TrafficCtrlUcastStromCtrl objects whether is enabled) will active storm control. Whenever a port reaches its configured amount of packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 64..1024000  

swL2TrafficCtrlBcastStromCtrl 1.3.6.1.4.1.171.11.63.10.2.11.1.1.4
This object indicates broadcast storm control function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrafficCtrlMcastStromCtrl 1.3.6.1.4.1.171.11.63.10.2.11.1.1.5
This object indicates multicast storm control function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrafficCtrlUcastStromCtrl 1.3.6.1.4.1.171.11.63.10.2.11.1.1.6
This object indicates destination lookup fail function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrafficSegTable 1.3.6.1.4.1.171.11.63.10.2.12.1
This table specifys the port just can forward traffic to the specific port list.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrafficSegEntry

swL2TrafficSegEntry 1.3.6.1.4.1.171.11.63.10.2.12.1.1
A list of information specifies the port with its traffic forward list.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2TrafficSegEntry  

swL2TrafficSegPort 1.3.6.1.4.1.171.11.63.10.2.12.1.1.1
The port number of the logical port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrafficSegForwardPorts 1.3.6.1.4.1.171.11.63.10.2.12.1.1.2
The port list that the specific port can forward traffic.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swL2PortSecurityControlTable 1.3.6.1.4.1.171.11.63.10.2.15.1
port security feature which controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this port, the first N learned addresses are locked at this port as static entry. When the learned addresses number reach N, any coming packet with not learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned at this port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortSecurityControlEntry

swL2PortSecurityControlEntry 1.3.6.1.4.1.171.11.63.10.2.15.1.1
A list of information contained in swL2PortSecurityControlTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2PortSecurityControlEntry  

swL2PortSecurityPortIndex 1.3.6.1.4.1.171.11.63.10.2.15.1.1.1
Indicates the secured port to lock address learning.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

swL2PortSecurityMaxLernAddr 1.3.6.1.4.1.171.11.63.10.2.15.1.1.2
Indicates allowable number of addresses to be learned at this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..10  

swL2PortSecurityMode 1.3.6.1.4.1.171.11.63.10.2.15.1.1.3
Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer expire. In this mode, when the locked address is aged out, the number of address can be learned has to be increased by one. In deleteOnReset(4) mode - never age out the locked addresses unless restart the system to prevent from port movement or intrusion.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), permanent(2), deleteOnTimeout(3), deleteOnReset(4)  

swL2PortSecurityAdmState 1.3.6.1.4.1.171.11.63.10.2.15.1.1.4
Indicates administration state of locking address.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), enable(2), disable(3)  

swL2PortSecurityEntryClearCtrl 1.3.6.1.4.1.171.11.63.10.2.15.1.1.5
Used to clear port security entries by port. Setting this value to 'start' will execute the clear action, Once cleared, the value returns to 'other'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), start(2)  

swL2PortSecurityTrapLogState 1.3.6.1.4.1.171.11.63.10.2.15.2
when enable(2),whenever there's a new MAC that violates the pre-defined port security configuration, trap will be sent out and the relevant information will be logged in system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), enable(2), disable(3)  

swL2StpForwardBPDU 1.3.6.1.4.1.171.11.63.10.2.16.1
Indicates whether flooding BPDU packets when STP is disabled on device
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2StpPortTable 1.3.6.1.4.1.171.11.63.10.2.16.4
A table that contains port-specific information for the Spanning Tree Protocol.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2StpPortEntry

swL2StpPortEntry 1.3.6.1.4.1.171.11.63.10.2.16.4.1
A list of information maintained by every port about the Spanning Tree Protocol state for that port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2StpPortEntry  

swL2StpPort 1.3.6.1.4.1.171.11.63.10.2.16.4.1.1
The port number of the port for this entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

swL2StpPortStatus 1.3.6.1.4.1.171.11.63.10.2.16.4.1.3
When the port Enable state is enabled, the port's current state as defined by application of the Spanning Tree Protocol. If the PortEnable is disabled, the the port status will be no-stp-enabled(7). If the port is in error disabled status, the port status will be err-disabled(8)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), disabled(2), discarding(3), learning(4), forwarding(5), broken(6), no-stp-enabled(7), err-disabled(8)  

swL2StpPortRole 1.3.6.1.4.1.171.11.63.10.2.16.4.1.4
When the port Enable state is enabled, the port's current port role as defined by application of the Spanning Tree Protocol. If the Port Enable state is disabled, the the port role will be nonstp(7). If the port is in loop-back status, the port role will be loopback(8)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), alternate(2), backup(3), root(4), designated(5), nonStp(6), loopback(7)  

swL2StpPortFBPDU 1.3.6.1.4.1.171.11.63.10.2.16.4.1.5
The enabled/disabled status is used to BPDU Filtering attached to this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2StpPortLinkState 1.3.6.1.4.1.171.11.63.10.2.16.4.1.6
This object indicates the stp port speed and duplex mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER link-down(1), half-10Mbps-none(2), half-10Mbps-backp(3), full-10Mbps-none(4), full-10Mbps-8023x(5), half-100Mbps-none(6), half-100Mbps-backp(7), full-100Mbps-none(8), full-100Mbps-8023x(9), half-1000Mbps-none(10), full-1000Mbps-backp(11), full-1000Mbps-none(12), full-1000Mbps-8023x(13)  

swL2StpPortProtocolMigration 1.3.6.1.4.1.171.11.63.10.2.16.4.1.7
When operating in RSTP (version 2) mode, writing TRUE(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns FALSE(2) when read.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

swL2StpPortAdminEdgePort 1.3.6.1.4.1.171.11.63.10.2.16.4.1.8
The administrative value of the Edge Port parameter. A value of TRUE(0) indicates that this port should be assumed as an edge-port and a value of FALSE(1) indicates that this port should be assumed as a non-edge-port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER forceTrue(0), forceFalse(1), auto(2)  

swL2StpPortOperEdgePort 1.3.6.1.4.1.171.11.63.10.2.16.4.1.9
The operational value of the Edge Port parameter. The object is initialized to the value of swL2StpPortAdminEdgePort and is set FALSE on reception of a BPDU.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

swL2StpPortAdminPointToPoint 1.3.6.1.4.1.171.11.63.10.2.16.4.1.10
The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER forceTrue(0), forceFalse(1), auto(2)  

swL2StpPortOperPointToPoint 1.3.6.1.4.1.171.11.63.10.2.16.4.1.11
The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the swL2StpPortAdminPointToPoint object.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

swL2StpPortAdminPathCost 1.3.6.1.4.1.171.11.63.10.2.16.4.1.12
The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object swL2StpPortPathCost, which returns the operational value of the path cost. Issue No.: 3250R2-077 As USE_RSTP is 1:enabled, swL2StpPortPathCost is forced to be read-only. configuration via swL2StpPortAdminPathCost. According 802.1w, value range of swL2StpPortAdminPathCost would be expanded. the former value range is (0..65535), the new is (0..200000000).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..200000000  

swL2StpPortPriority 1.3.6.1.4.1.171.11.63.10.2.16.4.1.13
The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of swL2StpPort.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..240  

swL2STPPortState 1.3.6.1.4.1.171.11.63.10.2.16.4.1.14
The enabled/disabled status is usedoop-back prevention attached to this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2StpPortRestrictedRole 1.3.6.1.4.1.171.11.63.10.2.16.4.1.15
If TRUE causes the port not to be selected as Root Port, even it has the best spanning tree priotiry vector.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

swL2StpPortRestrictedTCN 1.3.6.1.4.1.171.11.63.10.2.16.4.1.16
If TRUE causes the port not to propagate received topology change notifications and topology changes to other Ports.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

swL2CosPriorityCtrl 1.3.6.1.4.1.171.11.63.10.2.17.3
OBJECT IDENTIFIER    

swL2CosPriorityTable 1.3.6.1.4.1.171.11.63.10.2.17.3.1
Used to show and config per port priority-based QoS features on the switch
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2CosPriorityEntry

swL2CosPriorityEntry 1.3.6.1.4.1.171.11.63.10.2.17.3.1.1
A list of information contained in swL2CosPriorityTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2CosPriorityEntry  

swL2CosPriorityPort 1.3.6.1.4.1.171.11.63.10.2.17.3.1.1.1
The port number of CoS Priority.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

swL2CosPriorityPortPRI 1.3.6.1.4.1.171.11.63.10.2.17.3.1.1.2
Indicates port_priority state for CoS.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

swL2CosPriorityEtherPRI 1.3.6.1.4.1.171.11.63.10.2.17.3.1.1.3
Enable Ethernet frame based priority. When set ether8021p(2), enable 802.1p QoS; When set macBase(3), enable MAC-based QoS; When set disable(1), disable Ethernet frame based priority.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), ether8021p(2), macBase(3)  

swL2CosPriorityIpPRI 1.3.6.1.4.1.171.11.63.10.2.17.3.1.1.4
Enable IP priority QoS. When set tos(2), enable TOS based QoS; When set dscp(3), enable DSCP based QoS; When set disable(1), disable IP priority QoS.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), tos(2), dscp(3)  

swL2CosPriorityNone 1.3.6.1.4.1.171.11.63.10.2.17.3.1.1.5
when read,it always return invalid(2); when write valid(1),it disables all priority in this table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

swL2CosPortPRITable 1.3.6.1.4.1.171.11.63.10.2.17.3.2
Used to show port-to-class mappings and map specific port to one of the hardware queues available on the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2CosPortPRIEntry

swL2CosPortPRIEntry 1.3.6.1.4.1.171.11.63.10.2.17.3.2.1
A list of information contained in swL2CosPortPRITable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2CosPortPRIEntry  

swL2CosPortPRIIndex 1.3.6.1.4.1.171.11.63.10.2.17.3.2.1.1
Indicates CoS Priority PortPRI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

swL2CosPortPRIClass 1.3.6.1.4.1.171.11.63.10.2.17.3.2.1.2
The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges. And you can set value only 0 or 3,you can't set value 1 or 2.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..3  

swL2CosMacBasePRITable 1.3.6.1.4.1.171.11.63.10.2.17.3.3
Used to show MAC priority map to traffic class and map the destination MAC address in incoming packet to one of the hardware queues available on the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2CosMacBasePRIEntry

swL2CosMacBasePRIEntry 1.3.6.1.4.1.171.11.63.10.2.17.3.3.1
A list of information contained in swL2CosMacBasePRITable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2CosMacBasePRIEntry  

swL2CosMacBasePRIIndex 1.3.6.1.4.1.171.11.63.10.2.17.3.3.1.1
Indicates CoS Priority MacBasePRI.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

swL2CosMacBasePRIClass 1.3.6.1.4.1.171.11.63.10.2.17.3.3.1.2
The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..3  

swL2CosTosPRITable 1.3.6.1.4.1.171.11.63.10.2.17.3.4
Used to show TOS value to traffic class mapping and map the TOS value in the IP header of incoming packet to one of the four hardware queues available on the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2CosTosPRIEntry

swL2CosTosPRIEntry 1.3.6.1.4.1.171.11.63.10.2.17.3.4.1
A list of information contained in swL2CosTosPRITable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2CosTosPRIEntry  

swL2CosTosPRIIndex 1.3.6.1.4.1.171.11.63.10.2.17.3.4.1.1
Indicates CoS Priority TosPRI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

swL2CosTosPRIClass 1.3.6.1.4.1.171.11.63.10.2.17.3.4.1.2
The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..3  

swL2CosDscpPRITable 1.3.6.1.4.1.171.11.63.10.2.17.3.5
Used to show DSCP value to traffic class mapping and map the DSCP value in the IP header of incoming packet to one of the hardware queues available on the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2CosDscpPRIEntry

swL2CosDscpPRIEntry 1.3.6.1.4.1.171.11.63.10.2.17.3.5.1
A list of information contained in swL2CosDscpPRITable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2CosDscpPRIEntry  

swL2CosDscpPRIIndex 1.3.6.1.4.1.171.11.63.10.2.17.3.5.1.1
Indicates CoS Priority DscpPRI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..63  

swL2CosDscpPRIClass 1.3.6.1.4.1.171.11.63.10.2.17.3.5.1.2
The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..3  

swL2LoopDetectCtrl 1.3.6.1.4.1.171.11.63.10.2.18.1
OBJECT IDENTIFIER    

swL2LoopDetectAdminState 1.3.6.1.4.1.171.11.63.10.2.18.1.1
This object indicates the loopback detection status for the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL2LoopDetectInterval 1.3.6.1.4.1.171.11.63.10.2.18.1.2
This object indicates the interval value, the range is from 1 to 32767 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..32767  

swL2LoopDetectRecoverTime 1.3.6.1.4.1.171.11.63.10.2.18.1.3
This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1000000  

swL2LoopDetectPortMgmt 1.3.6.1.4.1.171.11.63.10.2.18.2
OBJECT IDENTIFIER    

swL2LoopDetectPortTable 1.3.6.1.4.1.171.11.63.10.2.18.2.1
The table specifies the loopback detection function specified by port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2LoopDetectPortEntry

swL2LoopDetectPortEntry 1.3.6.1.4.1.171.11.63.10.2.18.2.1.1
The table specifies the loopback detection function specified by port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2LoopDetectPortEntry  

swL2LoopDetectPortIndex 1.3.6.1.4.1.171.11.63.10.2.18.2.1.1.1
This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

swL2LoopDetectPortState 1.3.6.1.4.1.171.11.63.10.2.18.2.1.1.2
This object indicates the loopback detection function state on the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL2LoopDetectPortLoopStatus 1.3.6.1.4.1.171.11.63.10.2.18.2.1.1.4
This object indicates the port status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), loop(2), error(3)  

swL2VlanTable 1.3.6.1.4.1.171.11.63.10.2.19.1
A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2VlanEntry

swL2VlanEntry 1.3.6.1.4.1.171.11.63.10.2.19.1.1
Static information for a VLAN configured into the device by (local or network) management.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2VlanEntry  

swL2VlanIndex 1.3.6.1.4.1.171.11.63.10.2.19.1.1.1
The VLAN ID of the VLAN to be created. The range is 1 - 4094.
Status: current Access: read-only
OBJECT-TYPE    
  VlanId  

swL2VlanName 1.3.6.1.4.1.171.11.63.10.2.19.1.1.2
The name of the VLAN to be displayed.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

swL2VlanType 1.3.6.1.4.1.171.11.63.10.2.19.1.1.3
The type of the VLAN to be displayed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dynamic(0), static(1)  

swL2VlanMemberPorts 1.3.6.1.4.1.171.11.63.10.2.19.1.1.4
A range of member ports to the VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swL2VlanStaticPorts 1.3.6.1.4.1.171.11.63.10.2.19.1.1.5
A range of static ports to the VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swL2VlanUntaggedPorts 1.3.6.1.4.1.171.11.63.10.2.19.1.1.6
Specifies the additional ports as untagged.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swL2VlanTaggedPorts 1.3.6.1.4.1.171.11.63.10.2.19.1.1.7
Specifies the additional ports as tagged.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swL2Notify 1.3.6.1.4.1.171.11.63.10.2.100.1
OBJECT IDENTIFIER    

swL2NotifyPrefix 1.3.6.1.4.1.171.11.63.10.2.100.1.2
OBJECT IDENTIFIER    

swL2NotifFirmware 1.3.6.1.4.1.171.11.63.10.2.100.1.2.0
OBJECT IDENTIFIER    

swL2macNotification 1.3.6.1.4.1.171.11.63.10.2.100.1.2.0.1
This trap indicates the MAC addresses variation in address table .
Status: current Access: read-only
NOTIFICATION-TYPE    

swL2PortSecurityViolationTrap 1.3.6.1.4.1.171.11.63.10.2.100.1.2.0.2
When the port_security trap is enabled, new MAC addresses that violate the pre-defined port security configuration will trigger trap messages to be sent out.
Status: current Access: read-only
NOTIFICATION-TYPE    

swl2NotificationBidings 1.3.6.1.4.1.171.11.63.10.2.100.1.2.1
OBJECT IDENTIFIER    

swL2macNotifyInfo 1.3.6.1.4.1.171.11.63.10.2.100.1.2.1.1
This object indicates the last time reboot information.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..1024)  

swL2PortSecurityViolationMac 1.3.6.1.4.1.171.11.63.10.2.100.1.2.1.2
This object indicates the MAC address that violates the port security configuration.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress