DES-1210-10-AXME

File: DES-1210-10-AXME.mib (490060 bytes)

Imported modules

SNMPv2-SMI INET-ADDRESS-MIB IF-MIB
Q-BRIDGE-MIB SNMP-FRAMEWORK-MIB SNMPv2-TC

Imported symbols

MODULE-IDENTITY OBJECT-TYPE enterprises
IpAddress Integer32 Unsigned32
TimeTicks Counter32 InetAddress
InterfaceIndex InterfaceIndexOrZero VlanId
SnmpAdminString SnmpEngineID SnmpSecurityLevel
RowStatus TruthValue DisplayString
TEXTUAL-CONVENTION MacAddress

Defined Types

VlanIndex  
A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention). If the value is greater than 4095 then it represents a VLAN with scope local to the particular agent, i.e. one without a global VLAN-ID assigned to it. Such VLANs are outside the scope of IEEE 802.1Q but it is convenient to be able to manage them in the same way using this MIB.
TEXTUAL-CONVENTION    
  Unsigned32  

PortList  
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
TEXTUAL-CONVENTION    
  OCTET STRING  

BridgeId  
The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to refer to a bridge in a unique fashion (typically, the numerically smallest MAC address of all ports on the bridge). Several objects in this MIB module represent values of timers used by the Spanning Tree Protocol. In this MIB, these timers have values in units of hundreths of a second (i.e. 1/100 secs). These timers, when stored in a Spanning Tree Protocol's BPDU, are in units of 1/256 seconds. Note, however, that 802.1D-1990 specifies a settable granularity of no more than 1 second for these timers. To avoid ambiguity, a data type is defined here as a textual convention and all representation of these timers in this MIB module are defined using this data type. An algorithm is also defined for converting between the different units, to ensure a timer's value is not distorted by multiple conversions.
TEXTUAL-CONVENTION    
  OCTET STRING Size(8)  

Timeout  
A STP timer in units of 1/100 seconds To convert a Timeout value into a value in units of 1/256 seconds, the following algorithm should be used: b = floor( (n * 256) / 100) where: floor = quotient [ignore remainder] n is the value in 1/100 second units b is the value in 1/256 second units To convert the value from 1/256 second units back to 1/100 seconds, the following algorithm should be used: n = ceiling( (b * 100) / 256) where: ceiling = quotient [if remainder is 0], or quotient + 1 [if remainder is non-zero] n is the value in 1/100 second units b is the value in 1/256 second units Note: it is important that the arithmetic operations are done in the order specified (i.e., multiply first, divide second).
TEXTUAL-CONVENTION    
  INTEGER  

OwnerString  
This data type is used to model an administratively assigned name of the owner of a resource. Implementations must accept values composed of well-formed NVT ASCII sequences. In addition, implementations should accept values composed of well-formed UTF-8 sequences. It is suggested that this name contain one or more of the following: IP address, management station name, network manager's name, location, or phone number. In some cases the agent itself will be the owner of an entry. In these cases, this string shall be set to a string starting with 'monitor'. SNMP access control is articulated entirely in terms of the contents of MIB views; access to a particular SNMP object instance depends only upon its presence or absence in a particular MIB view and never upon its value or the value of related object instances. Thus, objects of this type afford resolution of resource contention only among cooperating managers; they realize no access control function with respect to uncooperative parties.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..127)  

RmonStatus  
The status of a table entry. Setting this object to the value invalid(4) has the effect of invalidating the corresponding entry. That is, it effectively disassociates the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries currently not in use. Proper interpretation of such entries requires examination of the relevant RmonStatus object. An existing instance of this object cannot be set to createRequest(2). This object may only be set to createRequest(2) when this instance is created. When this object is created, the agent may wish to create supplemental object instances with default values to complete a conceptual row in this table. Because the creation of these default objects is entirely at the option of the agent, the manager must not assume that any will be created, but may make use of any that are created. Immediately after completing the create operation, the agent must set this object to underCreation(3). When in the underCreation(3) state, an entry is allowed to exist in a possibly incomplete, possibly inconsistent state, usually to allow it to be modified in multiple PDUs. When in this state, an entry is not fully active. Entries shall exist in the underCreation(3) state until the management station is finished configuring the entry and sets this object to valid(1) or aborts, setting this object to invalid(4). If the agent determines that an entry has been in the underCreation(3) state for an abnormally long time, it may decide that the management station has crashed. If the agent makes this decision, it may set this object to invalid(4) to reclaim the entry. A prudent agent will understand that the management station may need to wait for human input and will allow for that possibility in its determination of this abnormally long period. An entry in the valid(1) state is fully configured and consistent and fully represents the configuration or operation such a row is intended to represent. For example, it could be a statistical function that is configured and active, or a filter that is available in the list of filters processed by the packet capture process. A manager is restricted to changing the state of an entry in the following ways: To: valid createRequest underCreation invalid From: valid OK NO OK OK createRequest N/A N/A N/A N/A underCreation OK NO OK OK invalid NO NO NO OK nonExistent NO OK NO OK In the table above, it is not applicable to move the state from the createRequest state to any other state because the manager will never find the variable in that state. The nonExistent state is not a value of the enumeration, rather it means that the entryStatus variable does not exist at all. An agent may allow an entryStatus variable to change state in additional ways, so long as the semantics of the states are followed. This allowance is made to ease the implementation of the agent and is made despite the fact that managers should never exercise these additional state transitions.
TEXTUAL-CONVENTION    
  INTEGER valid(1), createRequest(2), underCreation(3), invalid(4)  

SysPortCtrlEntry  
SEQUENCE    
  sysPortCtrlIndex Integer32
  sysPortCtrlMediumType INTEGER
  sysPortCtrlSpeed INTEGER
  sysPortCtrlOperStatus INTEGER
  sysPortCtrlMDI INTEGER
  sysPortCtrlFlowControl INTEGER
  sysPortCtrlFlowControlOper INTEGER
  sysPortCtrlType INTEGER

SysPortDescriptionEntry  
SEQUENCE    
  sysPortDescIndex INTEGER
  sysPortDescMediumType INTEGER
  sysPortDescString DisplayString

SysPortErrEntry  
SEQUENCE    
  sysPortErrPortIndex INTEGER
  sysPortErrPortState INTEGER
  sysPortErrPortStatus INTEGER
  sysPortErrPortReason INTEGER

StpPortEntry  
SEQUENCE    
  stpPort INTEGER
  stpPortStatus INTEGER
  stpPortPriority INTEGER
  stpAdminPortPathCost INTEGER
  stpPortPathCost INTEGER
  stpPortProtocolMigration TruthValue
  stpPortEdge INTEGER
  stpPortAdminP2P INTEGER
  stpPortRestrictedRole TruthValue
  stpPortRestrictedTCN TruthValue
  stpPortHelloTime Timeout
  stpPortState INTEGER
  stpPortFowardBPDU INTEGER

MstVlanMstiMappingEntry  
SEQUENCE    
  mstInstanceIndex Integer32
  mstSetVlanList OCTET STRING
  mstResetVlanList OCTET STRING
  mstInstanceVlanMapped OCTET STRING
  mstInstanceVlanMapped2k OCTET STRING
  mstInstanceVlanMapped3k OCTET STRING
  mstInstanceVlanMapped4k OCTET STRING

MstMstiBridgeEntry  
SEQUENCE    
  mstMstiInstanceIndex Integer32
  mstMstiBridgePriority Integer32
  mstMstiStatus INTEGER

MstCistPortEntry  
SEQUENCE    
  mstCistPort Integer32
  mstCistPortDesignatedBridge BridgeId
  mstCistPortAdminPathCost Integer32
  mstCistPortPathCost Integer32
  mstCistPortPriority Integer32
  mstCistForcePortState INTEGER
  mstCistCurrentPortRole INTEGER

MstMstiPortEntry  
SEQUENCE    
  mstMstiPort Integer32
  mstMstiPortDesignatedBridge BridgeId
  mstMstiPortAdminPathCost Integer32
  mstMstiPortPathCost Integer32
  mstMstiPortPriority Integer32
  mstMstiForcePortState INTEGER
  mstMstiCurrentPortRole INTEGER

StaticMcastEntry  
SEQUENCE    
  staticMcastVlanID INTEGER
  staticMcastMac MacAddress
  staticMcastEgressPorts PortList
  staticMcastStatus RowStatus

Dot1qVlanEntry  
SEQUENCE    
  dot1qVlanName SnmpAdminString
  dot1qVlanEgressPorts PortList
  dot1qVlanForbiddenPorts PortList
  dot1qVlanUntaggedPorts PortList
  dot1qVlanAdvertisementStatus INTEGER
  dot1qVlanRowStatus RowStatus

Dot1qVlanUngisterMCFilterEntry  
SEQUENCE    
  dot1qVlanUngisterMCFilterVlanId Integer32
  dot1qVlanUngisterMCFiltermode INTEGER

GvrpSettingsEntry  
SEQUENCE    
  gvrpSettingsPortControlIndex InterfaceIndex
  gvrpSettingsPVID INTEGER
  gvrpSettingsGVRPState INTEGER
  gvrpSettingsIngressChecking INTEGER
  gvrpSettingsAcceptableFrameType INTEGER

DHCPBOOTPRelayInterfaceSettings  
SEQUENCE    
  dhcpBOOTPRelayInterface DisplayString
  dhcpBOOTPRelayServerIP IpAddress
  dhcpBOOTPRelayInterfaceSettingsRowStatus RowStatus

DHCPLocalRelaySettings  
SEQUENCE    
  dhcpLocalRelaySettingsVLANID INTEGER
  dhcpLocalRelaySettingsState INTEGER

PortLaMode  
Defines how a Port Channel does channeling. lacp(1) - place the port into passive negotiation state, in which the port waits for its peer to initiate negotiation. static(2) - force the port to enable channeling. disable(3) - channeling is disabled.
TEXTUAL-CONVENTION    
  INTEGER lacp(1), static(2), disable(3)  

LacpKey  
The Actor or Partner Key value (0..65535).
TEXTUAL-CONVENTION    
  Integer32 0..65535  

LaPortChannelEntry  
SEQUENCE    
  laPortChannelIfIndex InterfaceIndex
  laPortChannelMemberList PortList
  laPortChannelMode PortLaMode
  laPortChannelMasterPort InterfaceIndex

LaPortControlEntry  
SEQUENCE    
  laPortControlIndex InterfaceIndex
  laPortActorPortPriority INTEGER
  laPortActorActivity INTEGER
  laPortActorTimeout INTEGER

StaticEntry  
SEQUENCE    
  staticVlanID INTEGER
  staticMac MacAddress
  staticPort INTEGER
  staticStatus RowStatus

IgsVlanRouterEntry  
SEQUENCE    
  igsVlanRouterVlanId Integer32
  igsVlanRouterPortList PortList

IgsVlanFilterEntry  
SEQUENCE    
  igsVlanFilterVlanId Integer32
  igsVlanSnoopStatus INTEGER
  igsVlanQuerier INTEGER
  igsVlanCfgQuerier INTEGER
  igsVlanQueryInterval Integer32
  igsVlanRtrPortList PortList
  igsVlanFbdRtrPortList PortList
  igsVlanFastLeave INTEGER

IgsVlanMulticastGroupEntry  
SEQUENCE    
  igsVlanMulticastGroupVlanId Integer32
  igsVlanMulticastGroupIpAddress InetAddress
  igsVlanMulticastGroupMacAddress MacAddress
  igsVlanMulticastGroupPortList PortList

IgsAccessAuthEntry  
SEQUENCE    
  igsAccessAuthPortIndex Integer32
  igsAccessAuthState INTEGER

SwAuthPortAccessControlEntry  
SEQUENCE    
  swAuthAuthConfigPortNumber INTEGER
  swAuthAuthQuietPeriod INTEGER
  swAuthAuthSuppTimeout INTEGER
  swAuthAuthServerTimeout INTEGER
  swAuthAuthMaxReq INTEGER
  swAuthAuthTxPeriod INTEGER
  swAuthAuthReAuthPeriod INTEGER
  swAuthAuthReAuthentication INTEGER
  swAuthAuthConfigPortControl INTEGER
  swAuthAuthCapability INTEGER
  swAuthAuthDirection INTEGER

SwAuthUserEntry  
SEQUENCE    
  swAuthUserName SnmpAdminString
  swAuthUserPassword DisplayString
  swAuthUserStatus RowStatus

SwAuthRadiusServerEntry  
SEQUENCE    
  swAuthRadiusServerIndex INTEGER
  swAuthRadiusServerAddress IpAddress
  swAuthRadiusServerAuthenticationPort INTEGER
  swAuthRadiusServerAccountingPort INTEGER
  swAuthRadiusServerTimeout INTEGER
  swAuthRadiusServerRetransmit INTEGER
  swAuthRadiusServerKey DisplayString
  swAuthRadiusServerStatus RowStatus

CosClassEntry  
SEQUENCE    
  cosClassIndex INTEGER
  cosWeight INTEGER

PortMapPriEntry  
SEQUENCE    
  portMapPriPortIndex INTEGER
  portMapPriClass INTEGER

QosDefaultUserPriEntry  
SEQUENCE    
  qosDefaultUserPriPortIndex INTEGER
  qosDefaultPriority INTEGER
  qosEffectiveDefaultPriority INTEGER

QosUserPriEntry  
SEQUENCE    
  qosUserPriIndex INTEGER
  qosUserPriClass INTEGER

QosPriSettingsEntry  
SEQUENCE    
  qosPriSetPortIndex INTEGER
  qosPriSetPortType INTEGER

AclQosEntry  
SEQUENCE    
  aclQosIndex Integer32
  aclQosType INTEGER
  aclQosMACAddr MacAddress
  aclQosIPAddr IpAddress
  aclQosTCPUDPPort Integer32
  aclQosVlanID Integer32
  aclQosProtocol Integer32
  aclQosAssignClass INTEGER
  aclQosStatus RowStatus

BandwidthCtrlEntry  
SEQUENCE    
  bandwidthCtrlIndex Integer32
  bandwidthCtrlTxThreshold Integer32
  bandwidthCtrlRxThreshold Integer32

TrafficCtrlEntry  
SEQUENCE    
  trafficCtrlIndex Integer32
  trafficCtrlActionMode INTEGER
  trafficCtrlType INTEGER
  trafficCtrlThreshold Integer32
  trafficCtrlCountDown Integer32
  trafficCtrlTimeInterval Integer32

TrustedHostEntry  
SEQUENCE    
  trustedHostIpAddr IpAddress
  trustedHostIpMask IpAddress
  trustedHostRowStatus RowStatus

ARPSpoofPreventEntry  
SEQUENCE    
  aRPSpoofPreventIpAddr IpAddress
  aRPSpoofPreventMacAddress MacAddress
  aRPSpoofPreventPortList PortList
  aRPSpoofPreventRowStatus RowStatus

SshUserInfoEntry  
SEQUENCE    
  sshUserInfoID Integer32
  sshUserInfoUserName DisplayString
  sshUserInfoAuth INTEGER
  sshUserInfoHostName DisplayString
  sshUserInfoHostIp IpAddress

PortSecEntry  
SEQUENCE    
  portSecIndex Integer32
  portSecState INTEGER
  portSecMLA Integer32
  portSecLockAddrMode INTEGER

PortSecFDBPermanentEntry  
SEQUENCE    
  portSecFDBPermIndex INTEGER
  portSecFDBPermVlanID INTEGER
  portSecFDBPermMac MacAddress
  portSecFDBPermPort INTEGER

AclProfileEntry  
SEQUENCE    
  aclProfileNo Integer32
  aclProfileType INTEGER
  aclProfileRuleCount Integer32
  aclProfileMask OCTET STRING
  aclProfileDstMacAddrMask MacAddress
  aclProfileSrcMacAddrMask MacAddress
  aclProfileIPProtocol INTEGER
  aclProfileIPProtocolMask OCTET STRING
  aclProfileDstIpAddrMask IpAddress
  aclProfileSrcIpAddrMask IpAddress
  aclProfileDstPortMask OCTET STRING
  aclProfileSrcPortMask OCTET STRING
  aclProfileArpSenderMacAddrMask MacAddress
  aclProfileArpSenderIpAddrMask IpAddress
  aclProfileStatus RowStatus

AclL2RuleEntry  
SEQUENCE    
  aclL2AccessID Integer32
  aclL2ProfileID Integer32
  aclL2RuleEtherType Integer32
  aclL2RuleDstMacAddr MacAddress
  aclL2RuleSrcMacAddr MacAddress
  aclL2RuleVlanId Integer32
  aclL2Rule1pPriority Integer32
  aclL2RuleDstMacAddrMask MacAddress
  aclL2RuleSrcMacAddrMask MacAddress
  aclL2RuleInPortList PortList
  aclL2RuleAction INTEGER
  aclL2RuleRateLimit Unsigned32
  aclL2RuleReplaceDSCP Integer32
  aclL2RuleStatus RowStatus

AclL3RuleEntry  
SEQUENCE    
  aclL3RuleAccessID Integer32
  aclL3RuleProfileNo Integer32
  aclL3RuleProtocol INTEGER
  aclL3RuleProtocolMask OCTET STRING
  aclL3RuleICMPMessageType Integer32
  aclL3RuleICMPMessageCode Integer32
  aclL3RuleDstIpAddr IpAddress
  aclL3RuleSrcIpAddr IpAddress
  aclL3RuleDstIpAddrMask IpAddress
  aclL3RuleSrcIpAddrMask IpAddress
  aclL3RuleTcpUdpDstPort Integer32
  aclL3RuleTcpUdpSrcPort Integer32
  aclL3RuleTcpUdpDstPortMask OCTET STRING
  aclL3RuleTcpUdpSrcPortMask OCTET STRING
  aclL3RuleTcpAckBit INTEGER
  aclL3RuleTcpRstBit INTEGER
  aclL3RuleTcpUrgBit INTEGER
  aclL3RuleTcpPshBit INTEGER
  aclL3RuleTcpSynBit INTEGER
  aclL3RuleTcpFinBit INTEGER
  aclL3RuleDscp Integer32
  aclL3RuleIgmpType Integer32
  aclL3RulePortList PortList
  aclL3RuleAction INTEGER
  aclL3RuleRateLimit Unsigned32
  aclL3RuleReplaceDSCP Integer32
  aclL3RuleStatus RowStatus

CpuFilterProfileEntry  
SEQUENCE    
  cpuFilterProfileNo Integer32
  cpuFilterProfileType INTEGER
  cpuFilterProfileRuleCount Integer32
  cpuFilterProfileMask OCTET STRING
  cpuFilterProfileDstMacAddrMask MacAddress
  cpuFilterProfileSrcMacAddrMask MacAddress
  cpuFilterProfileIPProtocol INTEGER
  cpuFilterProfileIPProtocolMask OCTET STRING
  cpuFilterProfileDstIpAddrMask IpAddress
  cpuFilterProfileSrcIpAddrMask IpAddress
  cpuFilterProfileDstPortMask OCTET STRING
  cpuFilterProfileSrcPortMask OCTET STRING
  cpuFilterProfileStatus RowStatus

CpuFilterL2RuleEntry  
SEQUENCE    
  cpuFilterL2ProfileID Integer32
  cpuFilterL2AccessID Integer32
  cpuFilterL2RuleEtherType Integer32
  cpuFilterL2RuleDstMacAddr MacAddress
  cpuFilterL2RuleSrcMacAddr MacAddress
  cpuFilterL2RuleVlanId Integer32
  cpuFilterL2Rule1pPriority Integer32
  cpuFilterL2RuleDstMacAddrMask MacAddress
  cpuFilterL2RuleSrcMacAddrMask MacAddress
  cpuFilterL2RuleInPortList PortList
  cpuFilterL2RuleAction INTEGER
  cpuFilterL2RuleStatus RowStatus

CpuFilterL3RuleEntry  
SEQUENCE    
  cpuFilterL3RuleProfileNo Integer32
  cpuFilterL3RuleAccessID Integer32
  cpuFilterL3RuleProtocol INTEGER
  cpuFilterL3RuleProtocolMask OCTET STRING
  cpuFilterL3RuleICMPMessageType Integer32
  cpuFilterL3RuleICMPMessageCode Integer32
  cpuFilterL3RuleDstIpAddr IpAddress
  cpuFilterL3RuleSrcIpAddr IpAddress
  cpuFilterL3RuleDstIpAddrMask IpAddress
  cpuFilterL3RuleSrcIpAddrMask IpAddress
  cpuFilterL3RuleTcpUdpDstPort Integer32
  cpuFilterL3RuleTcpUdpSrcPort Integer32
  cpuFilterL3RuleTcpUdpDstPortMask OCTET STRING
  cpuFilterL3RuleTcpUdpSrcPortMask OCTET STRING
  cpuFilterL3RuleTcpAckBit INTEGER
  cpuFilterL3RuleTcpRstBit INTEGER
  cpuFilterL3RuleTcpUrgBit INTEGER
  cpuFilterL3RuleTcpPshBit INTEGER
  cpuFilterL3RuleTcpSynBit INTEGER
  cpuFilterL3RuleTcpFinBit INTEGER
  cpuFilterL3RuleDscp Integer32
  cpuFilterL3RuleIgmpType Integer32
  cpuFilterL3RulePortList PortList
  cpuFilterL3RuleAction INTEGER
  cpuFilterL3RuleStatus RowStatus

SnmpV3UserEntry  
SEQUENCE    
  snmpV3UserName SnmpAdminString
  snmpV3UserVersion INTEGER
  snmpV3UserGroupName SnmpAdminString
  snmpV3UserAuthProtocol INTEGER
  snmpV3UserAuthProtocolPassword SnmpAdminString
  snmpV3UserPrivProtocol INTEGER
  snmpV3UserPrivProtocolPassword SnmpAdminString
  snmpV3UserStatus RowStatus

SnmpV3GroupEntry  
SEQUENCE    
  snmpV3GroupName SnmpAdminString
  snmpV3GroupSecurityModel INTEGER
  snmpV3GroupSecurityLevel SnmpSecurityLevel
  snmpV3GroupReadViewName SnmpAdminString
  snmpV3GroupWriteViewName SnmpAdminString
  snmpV3GroupNotifyViewName SnmpAdminString
  snmpV3GroupStatus RowStatus

SnmpV3ViewTreeEntry  
SEQUENCE    
  snmpV3viewTreeName SnmpAdminString
  snmpV3viewTreeSubtree OBJECT IDENTIFIER
  snmpV3viewTreeMask OCTET STRING
  snmpV3viewTreeType INTEGER
  snmpV3viewTreeStatus RowStatus

SnmpV3CommunityEntry  
SEQUENCE    
  snmpV3CommunityName OCTET STRING
  snmpV3CommunityPolicy SnmpAdminString
  snmpV3CommunityStatus RowStatus

SnmpV3HostEntry  
SEQUENCE    
  snmpV3HostAddress IpAddress
  snmpV3HostCommunityName SnmpAdminString
  snmpV3HostVersion INTEGER
  snmpV3HostStatus RowStatus

SyslogServEntry  
SEQUENCE    
  syslogServIndex INTEGER
  syslogServAddr IpAddress
  syslogServSeverity INTEGER
  syslogServFacility INTEGER
  syslogServUDPport INTEGER
  syslogServSrvStatus INTEGER
  syslogServSrvRowStatus RowStatus

SysLBDCtrlEntry  
SEQUENCE    
  sysLBDCtrlIndex Integer32
  sysLBDPortStatus INTEGER
  sysLBDPortLoopStatus INTEGER

VoiceVlanPortControlEntry  
SEQUENCE    
  voicevlanPortControlIndex InterfaceIndex
  voicevlanPortAutoDetection INTEGER
  voicevlanPortState INTEGER

VoicevlanOUIEntry  
SEQUENCE    
  voicevlanOUITelephonyOUI MacAddress
  voicevlanOUIDescription OCTET STRING
  voicevlanOUIMask MacAddress
  voicevlanOUIStatus RowStatus

AutoSurveillanceVlanOUIEntry  
SEQUENCE    
  autoSurveillanceVlanOUISurveillanceOUI MacAddress
  autoSurveillanceVlanOUIDescription OCTET STRING
  autoSurveillanceVlanOUIMask MacAddress
  autoSurveillanceVlanOUIStatus RowStatus
  autoSurveillanceVlanOUIComponentType INTEGER

MacNotifyCtrlEntry  
SEQUENCE    
  macNotifyCtrlIndex Integer32
  macNotifyPortStatus INTEGER

LldpPortNumber  
Each port contained in the chassis (that is known to the LLDP agent) is uniquely identified by a port number. A port number has no mandatory relationship to an InterfaceIndex object (of the interfaces MIB, IETF RFC 2863). If the LLDP agent is a IEEE 802.1D, IEEE 802.1Q bridge, the LldpPortNumber will have the same value as the dot1dBasePort object (defined in IETF RFC 1493) associated corresponding bridge port. If the system hosting LLDP agent is not an IEEE 802.1D or an IEEE 802.1Q bridge, the LldpPortNumber will have the same value as the corresponding interface's InterfaceIndex object. Port numbers should be in the range of 1 and 4096 since a particular port is also represented by the corresponding port number bit in LldpPortList.
TEXTUAL-CONVENTION    
  Integer32 1..4096  

LldpPortConfigEntry  
SEQUENCE    
  lldpPortConfigPortNum LldpPortNumber
  lldpPortConfigAdminStatus INTEGER
  lldpPortConfigNotificationEnable TruthValue
  lldpPortConfigTLVsTxEnable BITS

LldpPowerPortClass  
This TC describes the Power over Ethernet (PoE) port class.
TEXTUAL-CONVENTION    
  INTEGER pClassPSE(1), pClassPD(2)  

LldpLinkAggStatusMap  
This TC describes the link aggregation status. The bit 'aggCapable(0)' indicates the link is capable of being aggregated. The bit 'aggEnabled(1)' indicates the link is currently in aggregation.
TEXTUAL-CONVENTION    
  BITS aggCapable(0), aggEnabled(1)  

LldpXdot3PortConfigEntry  
SEQUENCE    
  lldpXdot3PortConfigTLVsTxEnable BITS

LldpXdot3LocPortEntry  
SEQUENCE    
  lldpXdot3LocPortAutoNegSupported TruthValue
  lldpXdot3LocPortAutoNegEnabled TruthValue
  lldpXdot3LocPortAutoNegAdvertisedCap OCTET STRING
  lldpXdot3LocPortOperMauType Integer32

LldpXdot3LocPowerEntry  
SEQUENCE    
  lldpXdot3LocPowerPortClass LldpPowerPortClass
  lldpXdot3LocPowerMDISupported TruthValue
  lldpXdot3LocPowerMDIEnabled TruthValue
  lldpXdot3LocPowerPairControlable TruthValue
  lldpXdot3LocPowerPairs Integer32
  lldpXdot3LocPowerClass Integer32

LldpXdot3LocLinkAggEntry  
SEQUENCE    
  lldpXdot3LocLinkAggStatus LldpLinkAggStatusMap
  lldpXdot3LocLinkAggPortId Integer32

LldpXdot3LocMaxFrameSizeEntry  
SEQUENCE    
  lldpXdot3LocMaxFrameSize Integer32

LldpXdot3RemPortEntry  
SEQUENCE    
  lldpXdot3RemPortAutoNegSupported TruthValue
  lldpXdot3RemPortAutoNegEnabled TruthValue
  lldpXdot3RemPortAutoNegAdvertisedCap OCTET STRING
  lldpXdot3RemPortOperMauType Integer32

LldpXdot3RemPowerEntry  
SEQUENCE    
  lldpXdot3RemPowerPortClass LldpPowerPortClass
  lldpXdot3RemPowerMDISupported TruthValue
  lldpXdot3RemPowerMDIEnabled TruthValue
  lldpXdot3RemPowerPairControlable TruthValue
  lldpXdot3RemPowerPairs Integer32
  lldpXdot3RemPowerClass Integer32

LldpXdot3RemLinkAggEntry  
SEQUENCE    
  lldpXdot3RemLinkAggStatus LldpLinkAggStatusMap
  lldpXdot3RemLinkAggPortId Integer32

LldpXdot3RemMaxFrameSizeEntry  
SEQUENCE    
  lldpXdot3RemMaxFrameSize Integer32

LldpXdot1ConfigPortVlanEntry  
SEQUENCE    
  lldpXdot1ConfigPortVlanTxEnable TruthValue

LldpXdot1LocVlanNameEntry  
SEQUENCE    
  lldpXdot1LocVlanId VlanId
  lldpXdot1LocVlanName SnmpAdminString

LldpXdot1ConfigVlanNameEntry  
SEQUENCE    
  lldpXdot1ConfigVlanNameTxEnable TruthValue

LldpXdot1LocProtoVlanEntry  
SEQUENCE    
  lldpXdot1LocProtoVlanId Integer32
  lldpXdot1LocProtoVlanSupported TruthValue
  lldpXdot1LocProtoVlanEnabled TruthValue

LldpXdot1ConfigProtoVlanEntry  
SEQUENCE    
  lldpXdot1ConfigProtoVlanTxEnable TruthValue

LldpXdot1LocProtocolEntry  
SEQUENCE    
  lldpXdot1LocProtocolIndex Integer32
  lldpXdot1LocProtocolId OCTET STRING

LldpXdot1ConfigProtocolEntry  
SEQUENCE    
  lldpXdot1ConfigProtocolTxEnable TruthValue

LldpXdot1LocEntry  
SEQUENCE    
  lldpXdot1LocPortVlanId Integer32

LldpXdot1RemEntry  
SEQUENCE    
  lldpXdot1RemPortVlanId Integer32

LldpXdot1RemProtoVlanEntry  
SEQUENCE    
  lldpXdot1RemProtoVlanId Integer32
  lldpXdot1RemProtoVlanSupported TruthValue
  lldpXdot1RemProtoVlanEnabled TruthValue

LldpXdot1RemVlanNameEntry  
SEQUENCE    
  lldpXdot1RemVlanId VlanId
  lldpXdot1RemVlanName SnmpAdminString

LldpXdot1RemProtocolEntry  
SEQUENCE    
  lldpXdot1RemProtocolIndex Integer32
  lldpXdot1RemProtocolId OCTET STRING

IpMacPortBindingEntry  
SEQUENCE    
  ipMacPortBindingIpAddr IpAddress
  ipMacPortBindingMacAddress MacAddress
  ipMacPortBindingPortList PortList
  ipMacPortBindingRowStatus RowStatus

MacBlockListEntry  
SEQUENCE    
  macBlockListMacAddr MacAddress
  macBlockListVLANID Integer32
  macBlockListPort Integer32
  macBlockListRowStatus RowStatus

FilterDHCPServerEntry  
SEQUENCE    
  filterDHCPServerIpAddr IpAddress
  filterDHCPServerClientMacAddr MacAddress
  filterDHCPServerPortList PortList
  filterDHCPServerRowStatus RowStatus

TrafficSegEntry  
SEQUENCE    
  trafficSegIfIndex InterfaceIndex
  trafficSegMemberList PortList

AacServerGroupEntry  
SEQUENCE    
  aacServerGroupIndex INTEGER
  aacServerGroupName OCTET STRING
  aacServersInGroup BITS
  aacServerGroupRowStatus RowStatus

AacServerInfoEntry  
SEQUENCE    
  aacServerIndex INTEGER
  aacServerIPAddr IpAddress
  aacServerAuthProtocol INTEGER
  aacServerAuthPort INTEGER
  aacServerAuthKey OCTET STRING
  aacServerTimeout INTEGER
  aacServerRetryCount INTEGER
  aacServerRowStatus RowStatus

AacLoginMethodListEntry  
SEQUENCE    
  aacLoginMethodListIndex INTEGER
  aacLoginMethodListName OCTET STRING
  aacLoginMethod1 INTEGER
  aacLoginMethod2 INTEGER
  aacLoginMethod3 INTEGER
  aacLoginMethod4 INTEGER
  aacLoginMethodListRowStatus RowStatus

AacEnableMethodListEntry  
SEQUENCE    
  aacEnableMethodListIndex INTEGER
  aacEnableMethodListName OCTET STRING
  aacEnableMethod1 INTEGER
  aacEnableMethod2 INTEGER
  aacEnableMethod3 INTEGER
  aacEnableMethod4 INTEGER
  aacEnableMethodListRowStatus RowStatus

SmtpRecvMailAddrEntry  
SEQUENCE    
  smtpRecvMailAddrIndex INTEGER
  smtpRecvMailAddr OCTET STRING
  smtpRecvMailAddrStatus RowStatus

IgmpMulticastVlanEntry  
SEQUENCE    
  igmpMulticastVlanid INTEGER
  igmpMulticastVlanName DisplayString
  igmpMulticastVlanSourcePort PortList
  igmpMulticastVlanMemberPort PortList
  igmpMulticastVlanTagMemberPort PortList
  igmpMulticastVlanState INTEGER
  igmpMulticastVlanReplaceSourceIp IpAddress
  igmpMulticastVlanRowStatus RowStatus

IgmpMulticastVlanGroupEntry  
SEQUENCE    
  igmpMulticastVlanGroupVid INTEGER
  igmpMulticastVlanGroupFromIp IpAddress
  igmpMulticastVlanGroupToIp IpAddress
  igmpMulticastVlanGroupStatus RowStatus

RmonStatsEntry  
SEQUENCE    
  rmonStatsIndex Integer32
  rmonStatsDataSource OBJECT IDENTIFIER
  rmonStatsOwner OwnerString
  rmonStatsStatus RmonStatus

RmonHistoryEntry  
SEQUENCE    
  rmonHistoryIndex Integer32
  rmonHistoryDataSource OBJECT IDENTIFIER
  rmonHistoryBucketsRequested Integer32
  rmonHistoryInterval Integer32
  rmonHistoryOwner OwnerString
  rmonHistoryStatus RmonStatus

RmonAlarmEntry  
SEQUENCE    
  rmonAlarmIndex Integer32
  rmonAlarmInterval Integer32
  rmonAlarmVariable OBJECT IDENTIFIER
  rmonAlarmSampleType INTEGER
  rmonAlarmRisingThreshold Integer32
  rmonAlarmFallingThreshold Integer32
  rmonAlarmRisingEventIndex Integer32
  rmonAlarmFallingEventIndex Integer32
  rmonAlarmOwner OwnerString
  rmonAlarmStatus RmonStatus

RmonEventEntry  
SEQUENCE    
  rmonEventIndex Integer32
  rmonEventDescription DisplayString
  rmonEventType INTEGER
  rmonEventCommunity OCTET STRING
  rmonEventOwner OwnerString
  rmonEventStatus RmonStatus

Defined Values




des-1210-10axme 1.3.6.1.4.1.171.10.75.14
OBJECT IDENTIFIER    

companySystem 1.3.6.1.4.1.171.10.75.14.1
OBJECT IDENTIFIER    

dhcpBOOTPRelayControl 1.3.6.1.4.1.171.10.75.14.28.1
OBJECT IDENTIFIER    

companyIpifGroup 1.3.6.1.4.1.171.10.75.14.2
OBJECT IDENTIFIER    

dhcpBOOTPRelayManagement 1.3.6.1.4.1.171.10.75.14.28.2
OBJECT IDENTIFIER    

dhcpBOOTPRelayManagementOption82 1.3.6.1.4.1.171.10.75.14.28.2.2
OBJECT IDENTIFIER    

companyTftpGroup 1.3.6.1.4.1.171.10.75.14.3
OBJECT IDENTIFIER    

companyMiscGroup 1.3.6.1.4.1.171.10.75.14.4
OBJECT IDENTIFIER    

companySNMPV3 1.3.6.1.4.1.171.10.75.14.5
OBJECT IDENTIFIER    

companySTP 1.3.6.1.4.1.171.10.75.14.6
OBJECT IDENTIFIER    

companyDot1qVlanGroup 1.3.6.1.4.1.171.10.75.14.7
OBJECT IDENTIFIER    

companyLA 1.3.6.1.4.1.171.10.75.14.8
OBJECT IDENTIFIER    

companyStaticMAC 1.3.6.1.4.1.171.10.75.14.9
OBJECT IDENTIFIER    

companyIgsGroup 1.3.6.1.4.1.171.10.75.14.10
OBJECT IDENTIFIER    

companyGVRPGroup 1.3.6.1.4.1.171.10.75.14.11
OBJECT IDENTIFIER    

companyQoSGroup 1.3.6.1.4.1.171.10.75.14.12
OBJECT IDENTIFIER    

companyTrafficMgmt 1.3.6.1.4.1.171.10.75.14.13
OBJECT IDENTIFIER    

companySecurity 1.3.6.1.4.1.171.10.75.14.14
OBJECT IDENTIFIER    

companyACLGroup 1.3.6.1.4.1.171.10.75.14.15
OBJECT IDENTIFIER    

companySyslog 1.3.6.1.4.1.171.10.75.14.16
OBJECT IDENTIFIER    

companyLBD 1.3.6.1.4.1.171.10.75.14.17
OBJECT IDENTIFIER    

companyMirror 1.3.6.1.4.1.171.10.75.14.18
OBJECT IDENTIFIER    

companyStaticMcast 1.3.6.1.4.1.171.10.75.14.19
OBJECT IDENTIFIER    

companySNTPSetting 1.3.6.1.4.1.171.10.75.14.20
OBJECT IDENTIFIER    

companyVoiceVlan 1.3.6.1.4.1.171.10.75.14.21
OBJECT IDENTIFIER    

companyRMON 1.3.6.1.4.1.171.10.75.14.22
OBJECT IDENTIFIER    

companyAuthGroup 1.3.6.1.4.1.171.10.75.14.23
OBJECT IDENTIFIER    

companyGuestVlan 1.3.6.1.4.1.171.10.75.14.24
OBJECT IDENTIFIER    

companyMacNotify 1.3.6.1.4.1.171.10.75.14.25
OBJECT IDENTIFIER    

companySMTP 1.3.6.1.4.1.171.10.75.14.26
OBJECT IDENTIFIER    

companyISMVLAN 1.3.6.1.4.1.171.10.75.14.27
OBJECT IDENTIFIER    

companyDHCPRelay 1.3.6.1.4.1.171.10.75.14.28
OBJECT IDENTIFIER    

companyDHCPLocalRelay 1.3.6.1.4.1.171.10.75.14.29
OBJECT IDENTIFIER    

companyTrapSetting 1.3.6.1.4.1.171.10.75.14.30
OBJECT IDENTIFIER    

companyLLDPSetting 1.3.6.1.4.1.171.10.75.14.32
OBJECT IDENTIFIER    

companyCPUInterfaceFilterGroup 1.3.6.1.4.1.171.10.75.14.33
OBJECT IDENTIFIER    

companyAutoSurveillanceVlan 1.3.6.1.4.1.171.10.75.14.34
OBJECT IDENTIFIER    

sysSwitchName 1.3.6.1.4.1.171.10.75.14.1.1
System name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character: ( ) ' + - = .
OBJECT-TYPE    
  DisplayString Size(1..20)  

sysHardwareVersion 1.3.6.1.4.1.171.10.75.14.1.2
Version number of the Hardware.
OBJECT-TYPE    
  DisplayString Size(1..15)  

sysFirmwareVersion 1.3.6.1.4.1.171.10.75.14.1.3
Version number of the Firmware.
OBJECT-TYPE    
  DisplayString Size(1..15)  

sysLoginTimeoutInterval 1.3.6.1.4.1.171.10.75.14.1.4
This time interval is used to count the time and logout web interface automatically.
OBJECT-TYPE    
  Integer32 3..30  

sysLocationName 1.3.6.1.4.1.171.10.75.14.1.5
The location name of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.
OBJECT-TYPE    
  DisplayString Size(1..20)  

sysGroupInterval 1.3.6.1.4.1.171.10.75.14.1.6
Group Interval is used to send D-link Discover packet to D-link SmartConsole Utility frequency. The timer in units of seconds. Set value 0 to disable group Interval.
OBJECT-TYPE    
  Integer32 0 | 120..1225  

sysSafeGuardEnable 1.3.6.1.4.1.171.10.75.14.1.8
This object is used to set Safeguard Enable\Disable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysRestart 1.3.6.1.4.1.171.10.75.14.1.9
This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switch to be restarted. When the switch operationally goes down, configuration save operation is initiated based on the configuration save option chosen. When the switch operationally come up, the saved configurations are restored based on the restore option chosen. Once the switch is restarted, the value of this object reverts to 'false'.
OBJECT-TYPE    
  TruthValue  

sysSave 1.3.6.1.4.1.171.10.75.14.1.10
This object is used to save Configuration.
OBJECT-TYPE    
  TruthValue  

sysPortCtrlTable 1.3.6.1.4.1.171.10.75.14.1.13
A table to control the port specific parameters of the device like speed, duplex mode, etc.
OBJECT-TYPE    
  SEQUENCE OF  
    SysPortCtrlEntry

sysPortCtrlEntry 1.3.6.1.4.1.171.10.75.14.1.13.1
An entry appears in this table for each interface in the system. Index to the table is the interface index of the port.
OBJECT-TYPE    
  SysPortCtrlEntry  

sysPortCtrlIndex 1.3.6.1.4.1.171.10.75.14.1.13.1.1
Interface index of the port for the configuration in this entry applies.
OBJECT-TYPE    
  Integer32 1..65535  

sysPortCtrlMediumType 1.3.6.1.4.1.171.10.75.14.1.13.1.2
This object indicates the port type: fiber 1G/100M or copper.
OBJECT-TYPE    
  INTEGER copper(100), fiber1G(101), fiber100M(102)  

sysPortCtrlSpeed 1.3.6.1.4.1.171.10.75.14.1.13.1.3
Configures interface speed.
OBJECT-TYPE    
  INTEGER rate1000M-Full(1), rate100M-Full(2), rate100M-Half(3), rate10M-Full(4), rate10M-Half(5), auto(6), disable(7)  

sysPortCtrlOperStatus 1.3.6.1.4.1.171.10.75.14.1.13.1.4
The port's operating speed state.
OBJECT-TYPE    
  INTEGER down(1), rate1000M-Full(2), rate100M-Full(3), rate100M-Half(4), rate10M-Full(5), rate10M-Half(6)  

sysPortCtrlMDI 1.3.6.1.4.1.171.10.75.14.1.13.1.5
Configures interface auto/mdi/mdix mode. The default setting is Auto.
OBJECT-TYPE    
  INTEGER auto(1), mdi(2), mdix(3)  

sysPortCtrlFlowControl 1.3.6.1.4.1.171.10.75.14.1.13.1.6
Enables / disables flow control for the interface.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysPortCtrlFlowControlOper 1.3.6.1.4.1.171.10.75.14.1.13.1.7
The link parner negotiate port's operating flow control state.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysPortCtrlType 1.3.6.1.4.1.171.10.75.14.1.13.1.8
The port's media type.
OBJECT-TYPE    
  INTEGER fastethernet(1), gigabitethernet(2), fiberwith100BaseSFPModule(3), fiberwith1000BaseSFPModule(4)  

sysPortDescriptionTable 1.3.6.1.4.1.171.10.75.14.1.14
The port description table.
OBJECT-TYPE    
  SEQUENCE OF  
    SysPortDescriptionEntry

sysPortDescriptionEntry 1.3.6.1.4.1.171.10.75.14.1.14.1
The port description entry.
OBJECT-TYPE    
  SysPortDescriptionEntry  

sysPortDescIndex 1.3.6.1.4.1.171.10.75.14.1.14.1.1
This object indicates the port index.
OBJECT-TYPE    
  INTEGER 1..255  

sysPortDescMediumType 1.3.6.1.4.1.171.10.75.14.1.14.1.2
This object indicates the port type: fiber 1G/100M or copper.
OBJECT-TYPE    
  INTEGER copper(100), fiber1G(101), fiber100M(102)  

sysPortDescString 1.3.6.1.4.1.171.10.75.14.1.14.1.3
This object indicates the port description.
OBJECT-TYPE    
  DisplayString Size(0..32)  

sysPortErrTable 1.3.6.1.4.1.171.10.75.14.1.15
The port error table.
OBJECT-TYPE    
  SEQUENCE OF  
    SysPortErrEntry

sysPortErrEntry 1.3.6.1.4.1.171.10.75.14.1.15.1
A list of information for the err port of the device.
OBJECT-TYPE    
  SysPortErrEntry  

sysPortErrPortIndex 1.3.6.1.4.1.171.10.75.14.1.15.1.1
This object indicates the module's port number.(1..Max port number in the module)
OBJECT-TYPE    
  INTEGER 1..255  

sysPortErrPortState 1.3.6.1.4.1.171.10.75.14.1.15.1.2
This object decides whether the port state is enabled or disabled.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

sysPortErrPortStatus 1.3.6.1.4.1.171.10.75.14.1.15.1.3
This object decides whether the PortStatus is err-disabled.
OBJECT-TYPE    
  INTEGER other(1), err-disabled(2)  

sysPortErrPortReason 1.3.6.1.4.1.171.10.75.14.1.15.1.4
This object decides whether the PortStatus is LBD.
OBJECT-TYPE    
  INTEGER lbd(1)  

sysDhcpAutoConfiguration 1.3.6.1.4.1.171.10.75.14.1.16
This object indicates auto config is enabled or disabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysWebState 1.3.6.1.4.1.171.10.75.14.1.17
This object is for Enabled(1) or Disabled(2) Web state in the system.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysWebPortNumber 1.3.6.1.4.1.171.10.75.14.1.18
Web Server Port Number.
OBJECT-TYPE    
  Integer32 1..65535  

sysARPAgingTime 1.3.6.1.4.1.171.10.75.14.1.19
This object is for ARP aging time.
OBJECT-TYPE    
  INTEGER 0..65535  

sysMACAgingTime 1.3.6.1.4.1.171.10.75.14.1.20
This object is for MAC aging time.
OBJECT-TYPE    
  INTEGER 10..600  

telnetsettingManagementOnOff 1.3.6.1.4.1.171.10.75.14.1.23
Enable/Disable management Telnetsetting mechanism.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

telnetUDPPort 1.3.6.1.4.1.171.10.75.14.1.24
The value is for setting telnet's UDP Port.
OBJECT-TYPE    
  INTEGER 1..65535  

autoRefreshConfiguration 1.3.6.1.4.1.171.10.75.14.1.25
To set the WEB panel auto refresh timer.
OBJECT-TYPE    
  INTEGER refreshimenever(0), refreshtime10secs(1), refreshtime30secs(2), refreshtime1min(3), refreshtime5mins(4)  

sysIpAddrCfgMode 1.3.6.1.4.1.171.10.75.14.2.1
Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system.
OBJECT-TYPE    
  INTEGER manual(1), dynamic(2)  

sysIpAddr 1.3.6.1.4.1.171.10.75.14.2.2
Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored.
OBJECT-TYPE    
  IpAddress  

sysIpSubnetMask 1.3.6.1.4.1.171.10.75.14.2.3
IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored.
OBJECT-TYPE    
  IpAddress  

sysGateway 1.3.6.1.4.1.171.10.75.14.2.4
Gateway
OBJECT-TYPE    
  IpAddress  

dhcpOption12Status 1.3.6.1.4.1.171.10.75.14.2.5
Status of DHCP Option12
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dhcpOption12HostName 1.3.6.1.4.1.171.10.75.14.2.6
Host name in DHCP option 12
OBJECT-TYPE    
  OCTET STRING  

tftpFwServerIpAddress 1.3.6.1.4.1.171.10.75.14.3.1
The TFTP server's IP address is used to upload or download firmware.
OBJECT-TYPE    
  IpAddress  

tftpFwImageFileName 1.3.6.1.4.1.171.10.75.14.3.2
Configure firmware filename to download.
OBJECT-TYPE    
  DisplayString Size(1..64)  

tftpFwTftpOperation 1.3.6.1.4.1.171.10.75.14.3.3
The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName.
OBJECT-TYPE    
  INTEGER none(0), download(1), upload(2)  

tftpFwTftpOperationStatus 1.3.6.1.4.1.171.10.75.14.3.4
The tftp operation status represent firmware backup or upgrade status.
OBJECT-TYPE    
  INTEGER none(0), success(1), fail(2), progressing(3), transmit(4)  

tftpCfgServerIpAddress 1.3.6.1.4.1.171.10.75.14.3.5
The TFTP server's IP address is used to upload or download configuration file.
OBJECT-TYPE    
  IpAddress  

tftpConfigFileName 1.3.6.1.4.1.171.10.75.14.3.6
The configuration filename is used to store or retrieve config from the tftp server.
OBJECT-TYPE    
  DisplayString Size(1..64)  

tftpConfigTftpOperation 1.3.6.1.4.1.171.10.75.14.3.7
The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName.
OBJECT-TYPE    
  INTEGER download(1), upload(2), progressing(3)  

tftpConfigTftpOperationStatus 1.3.6.1.4.1.171.10.75.14.3.8
The tftp operation status represent configuration file backup or restore status.
OBJECT-TYPE    
  INTEGER none(0), success(1), fail(2), progressing(3)  

miscReset 1.3.6.1.4.1.171.10.75.14.4.2
Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing.
OBJECT-TYPE    
  INTEGER reset(1), noop(2)  

miscStatisticsReset 1.3.6.1.4.1.171.10.75.14.4.3
Resets the units statistics. A (1) resets the statistics count, a (2) does nothing.
OBJECT-TYPE    
  INTEGER reset(1), noop(2)  

stpBridgeGlobal 1.3.6.1.4.1.171.10.75.14.6.1
OBJECT IDENTIFIER    

stpModuleStatus 1.3.6.1.4.1.171.10.75.14.6.1.1
The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

stpProtocolVersion 1.3.6.1.4.1.171.10.75.14.6.1.2
The version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.1D and 'rstp(2)' indicates the Rapid Spanning Tree Protocol specified in IEEE 802.1w and 'mstp(3)' indicates the Multiple Spanning Tree Protocol Specified in IEEE 802.1s.
OBJECT-TYPE    
  INTEGER stp(0), rstp(2), mstp(3)  

stpBridgePriority 1.3.6.1.4.1.171.10.75.14.6.1.3
The Value of the writable portion of the Bridge Identifier comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.
OBJECT-TYPE    
  Integer32 0..61440  

stpTxHoldCount 1.3.6.1.4.1.171.10.75.14.6.1.4
The value used by the Port Transmit state machine to limit the maximum transmission rate.
OBJECT-TYPE    
  Integer32 1..10  

stpBridgeMaxAge 1.3.6.1.4.1.171.10.75.14.6.1.5
The value that all bridges use for MaxAge when this bridge is acting as the root. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
OBJECT-TYPE    
  Timeout 600..4000  

stpBridgeHelloTime 1.3.6.1.4.1.171.10.75.14.6.1.6
The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second.
OBJECT-TYPE    
  Timeout 100..1000  

stpBridgeForwardDelay 1.3.6.1.4.1.171.10.75.14.6.1.7
The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D specifies that the range for this parameter is related to the value of BridgeMaxAge. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
OBJECT-TYPE    
  Timeout 400..3000  

stpFowardBPDU 1.3.6.1.4.1.171.10.75.14.6.1.8
This object is for enabling or disabling forward BPDU.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

stpRootBridge 1.3.6.1.4.1.171.10.75.14.6.1.9
The bridge identifier of the Root of the common spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the CIST Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
OBJECT-TYPE    
  BridgeId  

stpRootCost 1.3.6.1.4.1.171.10.75.14.6.1.10
The Cost of the path to the CIST Root as seen from this bridge.
OBJECT-TYPE    
  Integer32  

stpMaxAge 1.3.6.1.4.1.171.10.75.14.6.1.11
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
OBJECT-TYPE    
  Timeout  

stpForwardDelay 1.3.6.1.4.1.171.10.75.14.6.1.12
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in a particular state before moving to the next state.
OBJECT-TYPE    
  Timeout  

stpRootPort 1.3.6.1.4.1.171.10.75.14.6.1.13
The Port Number of the Port which offers the lowest path cost from this bridge to the CIST Root Bridge.
OBJECT-TYPE    
  Integer32  

stpPortTable 1.3.6.1.4.1.171.10.75.14.6.2
A table that contains port-specific information for the Spanning Tree Protocol.
OBJECT-TYPE    
  SEQUENCE OF  
    StpPortEntry

stpPortEntry 1.3.6.1.4.1.171.10.75.14.6.2.1
A list of information maintained by every port about the Spanning Tree Protocol state for that port.
OBJECT-TYPE    
  StpPortEntry  

stpPort 1.3.6.1.4.1.171.10.75.14.6.2.1.1
The Port number of the port for which this entry contains spanning tree information.
OBJECT-TYPE    
  INTEGER 1..65535  

stpPortStatus 1.3.6.1.4.1.171.10.75.14.6.2.1.2
Current state of the Port which can be changed to either Disabled or Enabled for ALL spanning tree instances. Setting this object will override the port's status in any of the MSTI contexts
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

stpPortPriority 1.3.6.1.4.1.171.10.75.14.6.2.1.3
The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting the CistPortPriority value. The values that are set for Port Priority must be in steps of 16.
OBJECT-TYPE    
  INTEGER 0..240  

stpAdminPortPathCost 1.3.6.1.4.1.171.10.75.14.6.2.1.4
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automatically calculated default Path Cost value to the ohter object stpPortPathCost. If the default Path Cost is being used,this object returns '0' when read.
OBJECT-TYPE    
  INTEGER 0..200000000  

stpPortPathCost 1.3.6.1.4.1.171.10.75.14.6.2.1.5
The contribution of this port to the path cost of paths towards the CIST Root which include this port.
OBJECT-TYPE    
  INTEGER 1..200000000  

stpPortProtocolMigration 1.3.6.1.4.1.171.10.75.14.6.2.1.6
Indicates the Protocol migration state of this Port. When operating in RSTP/MSTP (version >= 2) mode, writing TRUE(1) to this object forces this port to transmit MSTP BPDUs without instance information. Any other operation on this object has no effect and it always returns FALSE(2) when read.
OBJECT-TYPE    
  TruthValue  

stpPortEdge 1.3.6.1.4.1.171.10.75.14.6.2.1.7
This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled.
OBJECT-TYPE    
  INTEGER true(1), false(0), auto(2)  

stpPortAdminP2P 1.3.6.1.4.1.171.10.75.14.6.2.1.8
The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.
OBJECT-TYPE    
  INTEGER forceTrue(0), forceFalse(1), auto(2)  

stpPortRestrictedRole 1.3.6.1.4.1.171.10.75.14.6.2.1.9
A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected. This parameter should be FALSE by default. If set it can cause lack of spanning tree connectivity. It is set by a network administrator to prevent bridges external to a core region of the network influencing the spanning tree active topology, possibly because those bridges are not under the full control of the administrator. This administrator configuration is also known as 'Root Guard'.
OBJECT-TYPE    
  TruthValue  

stpPortRestrictedTCN 1.3.6.1.4.1.171.10.75.14.6.2.1.10
A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause temporary loss of connectivity after changes in a spanning trees active topology as a result of persistent incorrectly learnt station location information. It is set by a network administrator to prevent bridges external to a core region of the network causing address flushing in that region, possibly because those bridges are not under the full control of the administrator or MAC-Operational for the attached LANs transitions frequently.
OBJECT-TYPE    
  TruthValue  

stpPortHelloTime 1.3.6.1.4.1.171.10.75.14.6.2.1.11
The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second.
OBJECT-TYPE    
  Timeout 100..1000  

stpPortState 1.3.6.1.4.1.171.10.75.14.6.2.1.12
Current state of the Port as defined by the Common spanning tree protocol.
OBJECT-TYPE    
  INTEGER disabled(1), discarding(2), learning(4), forwarding(5)  

stpPortFowardBPDU 1.3.6.1.4.1.171.10.75.14.6.2.1.13
This object is for enabling or disabling forward BPDU.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

mstConfigurationIdentification 1.3.6.1.4.1.171.10.75.14.6.3
OBJECT IDENTIFIER    

mstiConfigurationName 1.3.6.1.4.1.171.10.75.14.6.3.1
The Name for the Region's configuration. By Default Region Name will be equal to the Bridge Mac Address.
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

mstiRevisionLevel 1.3.6.1.4.1.171.10.75.14.6.3.2
Version of the MST Region.
OBJECT-TYPE    
  Integer32 0..65535  

mstCistVlanMapped 1.3.6.1.4.1.171.10.75.14.6.3.3
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstCistVlanMapped2k 1.3.6.1.4.1.171.10.75.14.6.3.4
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstCistVlanMapped3k 1.3.6.1.4.1.171.10.75.14.6.3.5
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstCistVlanMapped4k 1.3.6.1.4.1.171.10.75.14.6.3.6
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstVlanMstiMappingTable 1.3.6.1.4.1.171.10.75.14.6.3.7
This table contains one entry for each instance of MSTP. This table maintains context ID as one more index to support Multiple Instances.
OBJECT-TYPE    
  SEQUENCE OF  
    MstVlanMstiMappingEntry

mstVlanMstiMappingEntry 1.3.6.1.4.1.171.10.75.14.6.3.7.1
A conceptual row containing the status of the MSTP instance.
OBJECT-TYPE    
  MstVlanMstiMappingEntry  

mstInstanceIndex 1.3.6.1.4.1.171.10.75.14.6.3.7.1.1
An arbitrary integer within the range from 1 to the value of Max Instance Number that uniquely identifies an instance.
OBJECT-TYPE    
  Integer32 1..15  

mstSetVlanList 1.3.6.1.4.1.171.10.75.14.6.3.7.1.2
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to map for this Instance. If the VlanId to Instance Mapping has to be known then any one of the VlanMapped object should be used.If a vlan is already mapped to this Instance, it may not be mapped again. This object is used only for SET operation. GET Operation returns null values.
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

mstResetVlanList 1.3.6.1.4.1.171.10.75.14.6.3.7.1.3
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to unmap from this Instance. A vlan may not be unmapped from this instance if it is not already mapped to this Instance. This object is used only for SET operation.GET Operation returns null values.
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

mstInstanceVlanMapped 1.3.6.1.4.1.171.10.75.14.6.3.7.1.4
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceVlanMapped2k 1.3.6.1.4.1.171.10.75.14.6.3.7.1.5
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceVlanMapped3k 1.3.6.1.4.1.171.10.75.14.6.3.7.1.6
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceVlanMapped4k 1.3.6.1.4.1.171.10.75.14.6.3.7.1.7
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

stpInstance 1.3.6.1.4.1.171.10.75.14.6.4
OBJECT IDENTIFIER    

mstCistBridgePriority 1.3.6.1.4.1.171.10.75.14.6.4.1
The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.
OBJECT-TYPE    
  Integer32 0..61440  

mstCistStatus 1.3.6.1.4.1.171.10.75.14.6.4.2
The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

mstMstiBridgeTable 1.3.6.1.4.1.171.10.75.14.6.4.3
Table containing Bridge Information specific to Spanning Tree Instance. This table maintains context ID as one more index to support Multiple Instances.
OBJECT-TYPE    
  SEQUENCE OF  
    MstMstiBridgeEntry

mstMstiBridgeEntry 1.3.6.1.4.1.171.10.75.14.6.4.3.1
Entry indicating the Bridge Information.
OBJECT-TYPE    
  MstMstiBridgeEntry  

mstMstiInstanceIndex 1.3.6.1.4.1.171.10.75.14.6.4.3.1.1
Spanning Tree Instance to which the information belongs.
OBJECT-TYPE    
  Integer32 1..15  

mstMstiBridgePriority 1.3.6.1.4.1.171.10.75.14.6.4.3.1.2
The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.
OBJECT-TYPE    
  Integer32 0..61440  

mstMstiStatus 1.3.6.1.4.1.171.10.75.14.6.4.3.1.3
The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

stpInstancePortTable 1.3.6.1.4.1.171.10.75.14.6.5
OBJECT IDENTIFIER    

mstCistPortTable 1.3.6.1.4.1.171.10.75.14.6.5.1
This table contains Common Spanning Tree Port Information.
OBJECT-TYPE    
  SEQUENCE OF  
    MstCistPortEntry

mstCistPortEntry 1.3.6.1.4.1.171.10.75.14.6.5.1.1
A list of information maintained by every port for Common Spanning tree.
OBJECT-TYPE    
  MstCistPortEntry  

mstCistPort 1.3.6.1.4.1.171.10.75.14.6.5.1.1.1
The Port number of the port for which this entry contains spanning tree information.
OBJECT-TYPE    
  Integer32 1..65535  

mstCistPortDesignatedBridge 1.3.6.1.4.1.171.10.75.14.6.5.1.1.2
The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.
OBJECT-TYPE    
  BridgeId  

mstCistPortAdminPathCost 1.3.6.1.4.1.171.10.75.14.6.5.1.1.3
The contribution of this port to the path cost of paths towards the MSTI Root which include this port.
OBJECT-TYPE    
  Integer32 0..200000000  

mstCistPortPathCost 1.3.6.1.4.1.171.10.75.14.6.5.1.1.4
The contribution of this port to the path cost of paths towards the MSTI Root which include this port.
OBJECT-TYPE    
  Integer32 1..200000000  

mstCistPortPriority 1.3.6.1.4.1.171.10.75.14.6.5.1.1.5
The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priority must be in steps of 16.
OBJECT-TYPE    
  Integer32 0..240  

mstCistForcePortState 1.3.6.1.4.1.171.10.75.14.6.5.1.1.6
Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' for this port
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mstCistCurrentPortRole 1.3.6.1.4.1.171.10.75.14.6.5.1.1.7
Current Port Role of the port for this spanning tree instance.
OBJECT-TYPE    
  INTEGER disabled(0), alternate(1), backup(2), root(3), designated(4), master(5)  

mstMstiPortTable 1.3.6.1.4.1.171.10.75.14.6.5.2
This table contains Spanning Tree Instance Specific Port Information.
OBJECT-TYPE    
  SEQUENCE OF  
    MstMstiPortEntry

mstMstiPortEntry 1.3.6.1.4.1.171.10.75.14.6.5.2.1
A list of information maintained by every port for each and every spanning tree instance.
OBJECT-TYPE    
  MstMstiPortEntry  

mstMstiPort 1.3.6.1.4.1.171.10.75.14.6.5.2.1.1
The Port number of the port for which this entry contains spanning tree information.
OBJECT-TYPE    
  Integer32 1..65535  

mstMstiPortDesignatedBridge 1.3.6.1.4.1.171.10.75.14.6.5.2.1.2
The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.
OBJECT-TYPE    
  BridgeId  

mstMstiPortAdminPathCost 1.3.6.1.4.1.171.10.75.14.6.5.2.1.3
The contribution of this port to the path cost of paths towards the MSTI Root which include this port.
OBJECT-TYPE    
  Integer32 0..200000000  

mstMstiPortPathCost 1.3.6.1.4.1.171.10.75.14.6.5.2.1.4
The contribution of this port to the path cost of paths towards the MSTI Root which include this port.
OBJECT-TYPE    
  Integer32 1..200000000  

mstMstiPortPriority 1.3.6.1.4.1.171.10.75.14.6.5.2.1.5
The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priority must be in steps of 16.
OBJECT-TYPE    
  Integer32 0..240  

mstMstiForcePortState 1.3.6.1.4.1.171.10.75.14.6.5.2.1.6
Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' for this port
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mstMstiCurrentPortRole 1.3.6.1.4.1.171.10.75.14.6.5.2.1.7
Current Port Role of the port for this spanning tree instance.
OBJECT-TYPE    
  INTEGER disabled(0), alternate(1), backup(2), root(3), designated(4), master(5)  

staticMcastTable 1.3.6.1.4.1.171.10.75.14.19.1
A list of the Static MACs
OBJECT-TYPE    
  SEQUENCE OF  
    StaticMcastEntry

staticMcastEntry 1.3.6.1.4.1.171.10.75.14.19.1.1
A Static MAC entry containing the mac and forwarding port.
OBJECT-TYPE    
  StaticMcastEntry  

staticMcastVlanID 1.3.6.1.4.1.171.10.75.14.19.1.1.1
The VLAN ID of the static MAC entry.
OBJECT-TYPE    
  INTEGER  

staticMcastMac 1.3.6.1.4.1.171.10.75.14.19.1.1.2
The MAC address associated of the static MAC entry.
OBJECT-TYPE    
  MacAddress  

staticMcastEgressPorts 1.3.6.1.4.1.171.10.75.14.19.1.1.3
The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of any dynamic information e.g. from GMRP. A port may not be added in this set if it is already a member of the set of ports in dot1qStaticMulticastForbiddenEgressPorts. The default value of this object is a string of ones of appropriate length.
OBJECT-TYPE    
  PortList  

staticMcastStatus 1.3.6.1.4.1.171.10.75.14.19.1.1.4
The status of an entry in the Static Mcast Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
OBJECT-TYPE    
  RowStatus  

dot1qVlanManagementOnOff 1.3.6.1.4.1.171.10.75.14.7.2
Enable/Disable management VLAN mechanism.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dot1qVlanManagementid 1.3.6.1.4.1.171.10.75.14.7.3
The management VLAN ID, which will allow to forward packets of that VLAN to CPU.
OBJECT-TYPE    
  INTEGER  

dot1qVlanAsyOnOff 1.3.6.1.4.1.171.10.75.14.7.5
Enable/Disable IEEE 802.1Q Asymmetric VLAN
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dot1qVlanTable 1.3.6.1.4.1.171.10.75.14.7.6
A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qVlanEntry

dot1qVlanEntry 1.3.6.1.4.1.171.10.75.14.7.6.1
Information for a VLAN configured into the device by (local or network) management.
OBJECT-TYPE    
  Dot1qVlanEntry  

dot1qVlanName 1.3.6.1.4.1.171.10.75.14.7.6.1.1
An administratively assigned string, which may be used to identify the VLAN.
OBJECT-TYPE    
  SnmpAdminString Size(0..20)  

dot1qVlanEgressPorts 1.3.6.1.4.1.171.10.75.14.7.6.1.2
The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros of appropriate length, indicating not fixed.
OBJECT-TYPE    
  PortList  

dot1qVlanForbiddenPorts 1.3.6.1.4.1.171.10.75.14.7.6.1.3
The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be included or excluded affect the per-port per-VLAN Registrar control for Registration Forbidden for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanEgressPorts. The default value of this object is a string of zeros of appropriate length, excluding all ports from the forbidden set.
OBJECT-TYPE    
  PortList  

dot1qVlanUntaggedPorts 1.3.6.1.4.1.171.10.75.14.7.6.1.4
The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device agent cannot support the set of ports being set then it will reject the set operation with an error. An example might be if a manager attempts to set more than one VLAN to be untagged on egress where the device does not support this IEEE 802.1Q option.
OBJECT-TYPE    
  PortList  

dot1qVlanAdvertisementStatus 1.3.6.1.4.1.171.10.75.14.7.6.1.5
Enable/Disable Advertisement Status of the IEEE 802.1Q VLAN.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dot1qVlanRowStatus 1.3.6.1.4.1.171.10.75.14.7.6.1.6
The status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanTable. It can be used as specified in the SNMP v2 standard.
OBJECT-TYPE    
  RowStatus  

dot1qVlanUngisterMCFilterTable 1.3.6.1.4.1.171.10.75.14.7.8
This table contains the list of ports through which a router, in a particular VLAN is reachable.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qVlanUngisterMCFilterEntry

dot1qVlanUngisterMCFilterEntry 1.3.6.1.4.1.171.10.75.14.7.8.1
A list of multicast filter mode information for each VLAN ID.
OBJECT-TYPE    
  Dot1qVlanUngisterMCFilterEntry  

dot1qVlanUngisterMCFilterVlanId 1.3.6.1.4.1.171.10.75.14.7.8.1.1
Per Vlan to configure multicast filtering function.
OBJECT-TYPE    
  Integer32 1..4094  

dot1qVlanUngisterMCFiltermode 1.3.6.1.4.1.171.10.75.14.7.8.1.2
Filter unknown multicast frames or normal operation(i.e. forwarding)
OBJECT-TYPE    
  INTEGER filter(1), forward(0)  

gvrpGVRPGlobalSettingsOnOff 1.3.6.1.4.1.171.10.75.14.11.1
Enable/Disable GVRP mechanism.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gvrpSettingsJoinTime 1.3.6.1.4.1.171.10.75.14.11.2
The Join Time value assigned to this Join Time field. This 16-bit value is read-write.
OBJECT-TYPE    
  INTEGER 100..100000  

gvrpSettingsLeaveTime 1.3.6.1.4.1.171.10.75.14.11.3
The Leave Time value assigned to this Leave Time field. This 16-bit value is read-write.
OBJECT-TYPE    
  INTEGER 100..100000  

gvrpSettingsLeaveAllTime 1.3.6.1.4.1.171.10.75.14.11.4
The Leave-All Time value assigned to this Leave-All Time field. This 16-bit value is read-write.
OBJECT-TYPE    
  INTEGER 100..100000  

gvrpSettingsTable 1.3.6.1.4.1.171.10.75.14.11.5
A table containing static configuration information for each GVRP configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
OBJECT-TYPE    
  SEQUENCE OF  
    GvrpSettingsEntry

gvrpSettingsEntry 1.3.6.1.4.1.171.10.75.14.11.5.1
Information for a GVRP configured into the device by (local or network) management.
OBJECT-TYPE    
  GvrpSettingsEntry  

gvrpSettingsPortControlIndex 1.3.6.1.4.1.171.10.75.14.11.5.1.1
The index of the port.
OBJECT-TYPE    
  InterfaceIndex  

gvrpSettingsPVID 1.3.6.1.4.1.171.10.75.14.11.5.1.2
The PVID value assigned to this Aggregation Port. This 16-bit value is read-write.
OBJECT-TYPE    
  INTEGER 1..4094  

gvrpSettingsGVRPState 1.3.6.1.4.1.171.10.75.14.11.5.1.3
Enable/Disable GVRP State to this Aggregation Port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gvrpSettingsIngressChecking 1.3.6.1.4.1.171.10.75.14.11.5.1.4
Enable/Disable Ingress Checking mechanism of GVRP to this Aggregation Port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gvrpSettingsAcceptableFrameType 1.3.6.1.4.1.171.10.75.14.11.5.1.5
Chose types All Frames/Tagged to this Aggregation Port.
OBJECT-TYPE    
  INTEGER allFrames(1), taggedOnly(2)  

dhcpBOOTPRelayState 1.3.6.1.4.1.171.10.75.14.28.1.1
This object indicates DHCP relay function is enabled or disabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dhcpBOOTPRelayHopCount 1.3.6.1.4.1.171.10.75.14.28.1.2
This object indicates the maximum number of router hops that the BOOTP packets can cross.
OBJECT-TYPE    
  INTEGER 1..16  

dhcpBOOTPRelayTimeThreshold 1.3.6.1.4.1.171.10.75.14.28.1.3
This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.
OBJECT-TYPE    
  INTEGER 0..65535  

dhcpBOOTPRelayInterfaceSettingsTable 1.3.6.1.4.1.171.10.75.14.28.2.1
This table indicates the IP address as a destination to forward (relay) DHCP packets to.
OBJECT-TYPE    
  SEQUENCE OF  
    DHCPBOOTPRelayInterfaceSettings

dhcpBOOTPRelayInterfaceSettingsEntry 1.3.6.1.4.1.171.10.75.14.28.2.1.1
A list of information indicates the IP address as a destination to forward (relay) DHCP packets to.
OBJECT-TYPE    
  DHCPBOOTPRelayInterfaceSettings  

dhcpBOOTPRelayInterface 1.3.6.1.4.1.171.10.75.14.28.2.1.1.1
This object indicates the name of the IP interface.
OBJECT-TYPE    
  DisplayString Size(0..12)  

dhcpBOOTPRelayServerIP 1.3.6.1.4.1.171.10.75.14.28.2.1.1.2
This object indicates the DHCP server IP address.
OBJECT-TYPE    
  IpAddress  

dhcpBOOTPRelayInterfaceSettingsRowStatus 1.3.6.1.4.1.171.10.75.14.28.2.1.1.3
This object indicates the status of this entry.
OBJECT-TYPE    
  RowStatus  

dhcpBOOTPRelayOption82State 1.3.6.1.4.1.171.10.75.14.28.2.2.1
This object indicates DHCP relay option 82 function is enabled or disabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dhcpBOOTPRelayOption82CheckState 1.3.6.1.4.1.171.10.75.14.28.2.2.2
This object indicates DHCP relay option 82 Check function is enabled or disabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dhcpBOOTPRelayOption82Policy 1.3.6.1.4.1.171.10.75.14.28.2.2.3
This object indicates DHCP relay option 82 policy.
OBJECT-TYPE    
  INTEGER replace(1), drop(2), keep(3)  

dhcpBOOTPRelayOption82RemoteIDType 1.3.6.1.4.1.171.10.75.14.28.2.2.4
This object indicates the type of remote ID. If the type is default, the remote ID will be the MAC address of the device, otherwise, the remote ID can be defined by writing to the swDHCPRelayOption82RemoteID object.
OBJECT-TYPE    
  INTEGER default(1), userdefined(2)  

dhcpBOOTPRelayOption82RemoteID 1.3.6.1.4.1.171.10.75.14.28.2.2.5
This object displays the current remote ID of the device. If swDHCPRelayOption82RemoteIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If swDHCPRelayOption82RemoteIDType is set to user-defined, a new value can be written to this object.
OBJECT-TYPE    
  DisplayString  

dhcpLocalRelayGlobalState 1.3.6.1.4.1.171.10.75.14.29.1
This object indicates DHCP local relay function of VLAN is enabled or disabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dhcpLocalRelayTable 1.3.6.1.4.1.171.10.75.14.29.2
This table indicates the IP address as a destination to forward (local relay) DHCP packets to.
OBJECT-TYPE    
  SEQUENCE OF  
    DHCPLocalRelaySettings

dhcpLocalRelayTableEntry 1.3.6.1.4.1.171.10.75.14.29.2.1
A list of information indicates the IP address as a destination to forward (local relay) DHCP packets to.
OBJECT-TYPE    
  DHCPLocalRelaySettings  

dhcpLocalRelaySettingsVLANID 1.3.6.1.4.1.171.10.75.14.29.2.1.1
This object displays the current VLAN ID of the device.
OBJECT-TYPE    
  INTEGER 1..4094  

dhcpLocalRelaySettingsState 1.3.6.1.4.1.171.10.75.14.29.2.1.2
This object indicates DHCP local relay function of VLAN is enabled or disabled.
OBJECT-TYPE    
  INTEGER enabled(3), disabled(2)  

laSystem 1.3.6.1.4.1.171.10.75.14.8.1
OBJECT IDENTIFIER    

laPortControl 1.3.6.1.4.1.171.10.75.14.8.2
OBJECT IDENTIFIER    

laStatus 1.3.6.1.4.1.171.10.75.14.8.1.2
Sets the Link Aggregation Module administrative status as enabled or disabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

laPortChannelTable 1.3.6.1.4.1.171.10.75.14.8.1.3
A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel.
OBJECT-TYPE    
  SEQUENCE OF  
    LaPortChannelEntry

laPortChannelEntry 1.3.6.1.4.1.171.10.75.14.8.1.3.1
There is one entry in this table for each created port-channel port.
OBJECT-TYPE    
  LaPortChannelEntry  

laPortChannelIfIndex 1.3.6.1.4.1.171.10.75.14.8.1.3.1.1
The index of the port-channel(Aggregator's interface index).
OBJECT-TYPE    
  InterfaceIndex  

laPortChannelMemberList 1.3.6.1.4.1.171.10.75.14.8.1.3.1.2
Member Port list of the port channel. Add the ports as a aggregation member associated of a port-channel.
OBJECT-TYPE    
  PortList  

laPortChannelMode 1.3.6.1.4.1.171.10.75.14.8.1.3.1.3
Current Operating Channel Mode of the port channel Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (Manual). disable(3) - channeling is disabled.
OBJECT-TYPE    
  PortLaMode  

laPortChannelMasterPort 1.3.6.1.4.1.171.10.75.14.8.1.3.1.4
The master port of the port-channel.
OBJECT-TYPE    
  InterfaceIndex  

laAlgorithm 1.3.6.1.4.1.171.10.75.14.8.1.4
Sets the Link Aggregation load balance algorithm.
OBJECT-TYPE    
  INTEGER sourceMAC(1), destMAC(2), sourceAndDestMAC(3), sourceIP(4), destIP(5), sourceAndDestIP(6)  

laPortControlTable 1.3.6.1.4.1.171.10.75.14.8.2.1
A table that contains Link Aggregation Control configuration information about every Aggregation Port associated with this device. A row appears in this table for each physical port.
OBJECT-TYPE    
  SEQUENCE OF  
    LaPortControlEntry

laPortControlEntry 1.3.6.1.4.1.171.10.75.14.8.2.1.1
A list of Link Aggregation Control configuration parameters for each Aggregation Port on this device.
OBJECT-TYPE    
  LaPortControlEntry  

laPortControlIndex 1.3.6.1.4.1.171.10.75.14.8.2.1.1.1
The index of the port.
OBJECT-TYPE    
  InterfaceIndex  

laPortActorPortPriority 1.3.6.1.4.1.171.10.75.14.8.2.1.1.2
The priority value assigned to this Aggregation Port. This 16-bit value is read-write.
OBJECT-TYPE    
  INTEGER 0..65535  

laPortActorActivity 1.3.6.1.4.1.171.10.75.14.8.2.1.1.3
This object indicates LACP-Activity to this Aggregation Port. LACP can be configured in one of two modes: active or passive. In active mode it will always send frames along the configured links. If the actor and partner are both in passive mode, they do not exchange LACP packets.
OBJECT-TYPE    
  INTEGER active(1), passive(2)  

laPortActorTimeout 1.3.6.1.4.1.171.10.75.14.8.2.1.1.4
This object indicates LACP-Timeout to this Aggregation Port. short(1) - LACP Timeout 3 seconds. long (2) - LACP Timeout 90 seconds.
OBJECT-TYPE    
  INTEGER short(1), long(2)  

staticDisableAutoLearn 1.3.6.1.4.1.171.10.75.14.9.1
Set on to disable Auto Learning Excluding Uplink Port and set off to enable Auto Learning.
OBJECT-TYPE    
  INTEGER on(1), off(2)  

staticAutoLearningList 1.3.6.1.4.1.171.10.75.14.9.2
The set of the device's member ports that belong to the Static MAC auto learning enable/disable. For example, when Disable Auto Learning is enable, the octet value set up as '# 0x0F 0xFF 0xFF 0xFF' means from port 1 to port 4 are not in auto learning state, the other ports are in auto learning state. It can be set up when Disable Auto Learning is enable.
OBJECT-TYPE    
  PortList  

staticTable 1.3.6.1.4.1.171.10.75.14.9.3
A list of the Static MACs
OBJECT-TYPE    
  SEQUENCE OF  
    StaticEntry

staticEntry 1.3.6.1.4.1.171.10.75.14.9.3.1
A Static MAC entry containing the mac and forwarding port.
OBJECT-TYPE    
  StaticEntry  

staticVlanID 1.3.6.1.4.1.171.10.75.14.9.3.1.1
The VLAN ID of the static MAC entry.
OBJECT-TYPE    
  INTEGER  

staticMac 1.3.6.1.4.1.171.10.75.14.9.3.1.2
The MAC address associated of the static MAC entry.
OBJECT-TYPE    
  MacAddress  

staticPort 1.3.6.1.4.1.171.10.75.14.9.3.1.3
The forwarding port of the static MAC entry.
OBJECT-TYPE    
  INTEGER  

staticStatus 1.3.6.1.4.1.171.10.75.14.9.3.1.4
The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static MAC.
OBJECT-TYPE    
  RowStatus  

igsSystem 1.3.6.1.4.1.171.10.75.14.10.1
OBJECT IDENTIFIER    

igsVlan 1.3.6.1.4.1.171.10.75.14.10.3
OBJECT IDENTIFIER    

igsAccessAuth 1.3.6.1.4.1.171.10.75.14.10.5
OBJECT IDENTIFIER    

igsStatus 1.3.6.1.4.1.171.10.75.14.10.1.1
Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module starts protocol operations. When set to 'disabled', the IGS module stops performing protocol operations.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

igsRouterPortPurgeInterval 1.3.6.1.4.1.171.10.75.14.10.1.2
This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted.
OBJECT-TYPE    
  Integer32 60..600  

igsHostPortPurgeInterval 1.3.6.1.4.1.171.10.75.14.10.1.3
This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group.
OBJECT-TYPE    
  Integer32 130..153025  

igsRobustnessValue 1.3.6.1.4.1.171.10.75.14.10.1.4
When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'igsRobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group.
OBJECT-TYPE    
  Integer32 2..255  

igsGrpQueryInterval 1.3.6.1.4.1.171.10.75.14.10.1.5
The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receivers. The switch will send 'igsRobustnessValue' queries before removing the port from the group membership information in the forwarding database.
OBJECT-TYPE    
  Integer32 1..25  

igsQueryInterval 1.3.6.1.4.1.171.10.75.14.10.1.6
This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for VLANs.
OBJECT-TYPE    
  Integer32 60..600  

igsQueryMaxResponseTime 1.3.6.1.4.1.171.10.75.14.10.1.7
The maximum query response time advertised in IGMPv2 general queries on this interface.
OBJECT-TYPE    
  INTEGER 10..25  

igsVlanRouterTable 1.3.6.1.4.1.171.10.75.14.10.3.3
This table contains the list of ports through which a router, in a particular VLAN is reachable.
OBJECT-TYPE    
  SEQUENCE OF  
    IgsVlanRouterEntry

igsVlanRouterEntry 1.3.6.1.4.1.171.10.75.14.10.3.3.1
Contains the VLAN ID and list of ports on which routers are present in the VLAN.
OBJECT-TYPE    
  IgsVlanRouterEntry  

igsVlanRouterVlanId 1.3.6.1.4.1.171.10.75.14.10.3.3.1.1
VLAN ID of the ports through which router is reachable.
OBJECT-TYPE    
  Integer32 1..4094  

igsVlanRouterPortList 1.3.6.1.4.1.171.10.75.14.10.3.3.1.2
List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.
OBJECT-TYPE    
  PortList  

igsVlanFilterTable 1.3.6.1.4.1.171.10.75.14.10.3.4
This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    IgsVlanFilterEntry

igsVlanFilterEntry 1.3.6.1.4.1.171.10.75.14.10.3.4.1
Contains snooping status , version and fast leave configuration for a specific VLAN.
OBJECT-TYPE    
  IgsVlanFilterEntry  

igsVlanFilterVlanId 1.3.6.1.4.1.171.10.75.14.10.3.4.1.1
Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done.
OBJECT-TYPE    
  Integer32 1..4094  

igsVlanSnoopStatus 1.3.6.1.4.1.171.10.75.14.10.3.4.1.2
This object allows you to enable/disable IGS function on a specific VLAN.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

igsVlanQuerier 1.3.6.1.4.1.171.10.75.14.10.3.4.1.3
Indicates whether the switch is configured as a querier in the VLAN
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

igsVlanCfgQuerier 1.3.6.1.4.1.171.10.75.14.10.3.4.1.4
The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

igsVlanQueryInterval 1.3.6.1.4.1.171.10.75.14.10.3.4.1.5
This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network.
OBJECT-TYPE    
  Integer32 60..600  

igsVlanRtrPortList 1.3.6.1.4.1.171.10.75.14.10.3.4.1.6
List of ports which are configured statically as router ports
OBJECT-TYPE    
  PortList  

igsVlanFbdRtrPortList 1.3.6.1.4.1.171.10.75.14.10.3.4.1.7
List of ports which can be configured statically as forbidden router ports.
OBJECT-TYPE    
  PortList  

igsVlanFastLeave 1.3.6.1.4.1.171.10.75.14.10.3.4.1.8
Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

igsVlanMulticastGroupTable 1.3.6.1.4.1.171.10.75.14.10.3.5
This table contains MAC based multicast forwarding information.
OBJECT-TYPE    
  SEQUENCE OF  
    IgsVlanMulticastGroupEntry

igsVlanMulticastGroupEntry 1.3.6.1.4.1.171.10.75.14.10.3.5.1
This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded.
OBJECT-TYPE    
  IgsVlanMulticastGroupEntry  

igsVlanMulticastGroupVlanId 1.3.6.1.4.1.171.10.75.14.10.3.5.1.1
VLAN ID pertaining to the Multicast forwarding entry
OBJECT-TYPE    
  Integer32 1..4094  

igsVlanMulticastGroupIpAddress 1.3.6.1.4.1.171.10.75.14.10.3.5.1.2
Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format.
OBJECT-TYPE    
  InetAddress  

igsVlanMulticastGroupMacAddress 1.3.6.1.4.1.171.10.75.14.10.3.5.1.3
Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format.
OBJECT-TYPE    
  MacAddress  

igsVlanMulticastGroupPortList 1.3.6.1.4.1.171.10.75.14.10.3.5.1.4
List of ports onto which the multicast data packets destined for this group will be forwarded.
OBJECT-TYPE    
  PortList  

igsAccessAuthTable 1.3.6.1.4.1.171.10.75.14.10.5.1
This table is used to manage the IGMP Authentication function of the switch.
OBJECT-TYPE    
  SEQUENCE OF  
    IgsAccessAuthEntry

igsAccessAuthEntry 1.3.6.1.4.1.171.10.75.14.10.5.1.1
Contains management entities for IGMP Authentication function.
OBJECT-TYPE    
  IgsAccessAuthEntry  

igsAccessAuthPortIndex 1.3.6.1.4.1.171.10.75.14.10.5.1.1.1
The port index of igsAccessAuthTable which indicates the port to be configured.
OBJECT-TYPE    
  Integer32  

igsAccessAuthState 1.3.6.1.4.1.171.10.75.14.10.5.1.1.2
This object can be configured to set IGMP Authentication state to enabled/disabled on each port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swAuthenCtrl 1.3.6.1.4.1.171.10.75.14.23.1
OBJECT IDENTIFIER    

swAuthStatus 1.3.6.1.4.1.171.10.75.14.23.1.1
Enable/Disable Static 802.1x.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swAuthMode 1.3.6.1.4.1.171.10.75.14.23.1.2
This object indicates the authentication mode of the device.
OBJECT-TYPE    
  INTEGER portBase(1), macBase(2)  

authProtocol 1.3.6.1.4.1.171.10.75.14.23.1.3
The authentication method used to authenticate users.
OBJECT-TYPE    
  INTEGER authProtocolRadiusEap(1), authProtocolLocal(2)  

swAuthPortAccessCtrl 1.3.6.1.4.1.171.10.75.14.23.2
OBJECT IDENTIFIER    

swAuthPortAccessControlTable 1.3.6.1.4.1.171.10.75.14.23.2.1
A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.
OBJECT-TYPE    
  SEQUENCE OF  
    SwAuthPortAccessControlEntry

swAuthPortAccessControlEntry 1.3.6.1.4.1.171.10.75.14.23.2.1.1
The configuration information for an Authenticator Port.
OBJECT-TYPE    
  SwAuthPortAccessControlEntry  

swAuthAuthConfigPortNumber 1.3.6.1.4.1.171.10.75.14.23.2.1.1.1
A unique value for each port that correlates to port index. Its value ranges between 1 and the value of port number.
OBJECT-TYPE    
  INTEGER  

swAuthAuthQuietPeriod 1.3.6.1.4.1.171.10.75.14.23.2.1.1.2
The value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine.
OBJECT-TYPE    
  INTEGER 0..65535  

swAuthAuthSuppTimeout 1.3.6.1.4.1.171.10.75.14.23.2.1.1.3
The value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine.
OBJECT-TYPE    
  INTEGER 1..65535  

swAuthAuthServerTimeout 1.3.6.1.4.1.171.10.75.14.23.2.1.1.4
The value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine.
OBJECT-TYPE    
  INTEGER 1..65535  

swAuthAuthMaxReq 1.3.6.1.4.1.171.10.75.14.23.2.1.1.5
The value of the maxReq constant currently in use by the Backend Authentication state machine.
OBJECT-TYPE    
  INTEGER 1..10  

swAuthAuthTxPeriod 1.3.6.1.4.1.171.10.75.14.23.2.1.1.6
The value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine.
OBJECT-TYPE    
  INTEGER 1..65535  

swAuthAuthReAuthPeriod 1.3.6.1.4.1.171.10.75.14.23.2.1.1.7
The value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine.
OBJECT-TYPE    
  INTEGER 1..65535  

swAuthAuthReAuthentication 1.3.6.1.4.1.171.10.75.14.23.2.1.1.8
The enable/disable control used by the Reauthentication Timer state machine (8.5.5.1).
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swAuthAuthConfigPortControl 1.3.6.1.4.1.171.10.75.14.23.2.1.1.9
The current value of the controlled Port control parameter for the Port.
OBJECT-TYPE    
  INTEGER forceUnauthorized(1), auto(2), forceAuthorized(3)  

swAuthAuthCapability 1.3.6.1.4.1.171.10.75.14.23.2.1.1.10
The current value of the controlled Port control parameter for the Port.
OBJECT-TYPE    
  INTEGER authenticator(1), none(2)  

swAuthAuthDirection 1.3.6.1.4.1.171.10.75.14.23.2.1.1.11
The current value of the controlled Port control parameter for the Port.
OBJECT-TYPE    
  INTEGER both(0), in(1)  

swAuthUser 1.3.6.1.4.1.171.10.75.14.23.3
OBJECT IDENTIFIER    

swAuthUserTable 1.3.6.1.4.1.171.10.75.14.23.3.1
A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.
OBJECT-TYPE    
  SEQUENCE OF  
    SwAuthUserEntry

swAuthUserEntry 1.3.6.1.4.1.171.10.75.14.23.3.1.1
The configuration information for an Authenticator Port.
OBJECT-TYPE    
  SwAuthUserEntry  

swAuthUserName 1.3.6.1.4.1.171.10.75.14.23.3.1.1.1
The unique index value of a row in this table. This object is used to set 802.1X Local user name, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.
OBJECT-TYPE    
  SnmpAdminString Size(1..15)  

swAuthUserPassword 1.3.6.1.4.1.171.10.75.14.23.3.1.1.2
This object is used to set 802.1X Local user Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.
OBJECT-TYPE    
  DisplayString Size(1..15)  

swAuthUserStatus 1.3.6.1.4.1.171.10.75.14.23.3.1.1.3
The status of this conceptual row in the swAuthUserTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthUserName objects must be explicitly set.
OBJECT-TYPE    
  RowStatus  

swAuthRadiusServer 1.3.6.1.4.1.171.10.75.14.23.4
OBJECT IDENTIFIER    

swAuthRadiusServerTable 1.3.6.1.4.1.171.10.75.14.23.4.1
A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.
OBJECT-TYPE    
  SEQUENCE OF  
    SwAuthRadiusServerEntry

swAuthRadiusServerEntry 1.3.6.1.4.1.171.10.75.14.23.4.1.1
The configuration information for an Authenticator Port.
OBJECT-TYPE    
  SwAuthRadiusServerEntry  

swAuthRadiusServerIndex 1.3.6.1.4.1.171.10.75.14.23.4.1.1.1
A unique value for Authentication RADIUS Server index. Its value ranges between 1 and 3.
OBJECT-TYPE    
  INTEGER 1..3  

swAuthRadiusServerAddress 1.3.6.1.4.1.171.10.75.14.23.4.1.1.2
The IP address of the RADIUS server referred to in this table entry.
OBJECT-TYPE    
  IpAddress  

swAuthRadiusServerAuthenticationPort 1.3.6.1.4.1.171.10.75.14.23.4.1.1.3
The value is for setting UDP Port.
OBJECT-TYPE    
  INTEGER 1..65535  

swAuthRadiusServerAccountingPort 1.3.6.1.4.1.171.10.75.14.23.4.1.1.4
The value is for setting UDP Port.
OBJECT-TYPE    
  INTEGER 1..65535  

swAuthRadiusServerTimeout 1.3.6.1.4.1.171.10.75.14.23.4.1.1.5
The value is for setting UDP Port.
OBJECT-TYPE    
  INTEGER 1..255  

swAuthRadiusServerRetransmit 1.3.6.1.4.1.171.10.75.14.23.4.1.1.6
The value is for setting UDP Port.
OBJECT-TYPE    
  INTEGER 1..255  

swAuthRadiusServerKey 1.3.6.1.4.1.171.10.75.14.23.4.1.1.7
This object is used to set 802.1X Radius Server Key, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.
OBJECT-TYPE    
  DisplayString Size(1..15)  

swAuthRadiusServerStatus 1.3.6.1.4.1.171.10.75.14.23.4.1.1.8
The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthRadiusServerIndex objects must be explicitly set.
OBJECT-TYPE    
  RowStatus  

cosScheduleMechanism 1.3.6.1.4.1.171.10.75.14.12.1
Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin Strict-priority scheduling is implemented with a special strict-priority scheduler node that is stacked directly above the port. Queues stacked on top of the strict-priority scheduler node always get bandwidth before other queues. Weighted round-robin scheduling is designed to better handle queues with different processing capacities. Each queue has a weight : Low is 1, Medium is 2, High is 4 and Highest is 8 for WS3 spec. Queues with higher weights get bandwidth before than other queues with less weights.
OBJECT-TYPE    
  INTEGER strictPriority(1), wrr(2)  

cosOutputSchedule 1.3.6.1.4.1.171.10.75.14.12.2
OBJECT IDENTIFIER    

cosClassTable 1.3.6.1.4.1.171.10.75.14.12.2.1
A list of cosOutputSchedule.
OBJECT-TYPE    
  SEQUENCE OF  
    CosClassEntry

cosClassEntry 1.3.6.1.4.1.171.10.75.14.12.2.1.1
A list of cosOutputClass Weight.
OBJECT-TYPE    
  CosClassEntry  

cosClassIndex 1.3.6.1.4.1.171.10.75.14.12.2.1.1.1
A index of class 0 ~ 3.
OBJECT-TYPE    
  INTEGER 0..3  

cosWeight 1.3.6.1.4.1.171.10.75.14.12.2.1.1.2
cos weight
OBJECT-TYPE    
  INTEGER 1..55  

portMapPriority 1.3.6.1.4.1.171.10.75.14.12.3
OBJECT IDENTIFIER    

portMapPriTable 1.3.6.1.4.1.171.10.75.14.12.3.1
A list of port mapping priority Entries.
OBJECT-TYPE    
  SEQUENCE OF  
    PortMapPriEntry

portMapPriEntry 1.3.6.1.4.1.171.10.75.14.12.3.1.1
A list of 802.1p port mapping priority priorities.
OBJECT-TYPE    
  PortMapPriEntry  

portMapPriPortIndex 1.3.6.1.4.1.171.10.75.14.12.3.1.1.1
A port identifier that is in the range of 1 to ifNumber.
OBJECT-TYPE    
  INTEGER  

portMapPriClass 1.3.6.1.4.1.171.10.75.14.12.3.1.1.2
For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization. For ingress tagged packets, if 802.1p not enabled D-Link Smart Switches will refer to these 4 different priority queues.
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDefaultUserPri 1.3.6.1.4.1.171.10.75.14.12.4
OBJECT IDENTIFIER    

qosDefaultUserPriTable 1.3.6.1.4.1.171.10.75.14.12.4.1
A list of 802.1p port default priority Entries.
OBJECT-TYPE    
  SEQUENCE OF  
    QosDefaultUserPriEntry

qosDefaultUserPriEntry 1.3.6.1.4.1.171.10.75.14.12.4.1.1
A list of 802.1p port default priority priorities.
OBJECT-TYPE    
  QosDefaultUserPriEntry  

qosDefaultUserPriPortIndex 1.3.6.1.4.1.171.10.75.14.12.4.1.1.1
A port identifier that is in the range of 1 to ifNumber.
OBJECT-TYPE    
  INTEGER  

qosDefaultPriority 1.3.6.1.4.1.171.10.75.14.12.4.1.1.2
For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled.
OBJECT-TYPE    
  INTEGER priority0(0), priority1(1), priority2(2), priority3(3), priority4(4), priority5(5), priority6(6), priority7(7)  

qosEffectiveDefaultPriority 1.3.6.1.4.1.171.10.75.14.12.4.1.1.3
For ingress untagged packets, the per port 'Effective Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled.
OBJECT-TYPE    
  INTEGER priority0(0), priority1(1), priority2(2), priority3(3), priority4(4), priority5(5), priority6(6), priority7(7)  

qosUserPriority 1.3.6.1.4.1.171.10.75.14.12.5
OBJECT IDENTIFIER    

qosUserPriorityTable 1.3.6.1.4.1.171.10.75.14.12.5.1
A table mapping evaluated User Priority to Traffic Class, for forwarding by the bridge. Traffic class is a number in the range (0..3).
OBJECT-TYPE    
  SEQUENCE OF  
    QosUserPriEntry

qosUserPriEntry 1.3.6.1.4.1.171.10.75.14.12.5.1.1
User Priority to Traffic Class mapping.
OBJECT-TYPE    
  QosUserPriEntry  

qosUserPriIndex 1.3.6.1.4.1.171.10.75.14.12.5.1.1.1
For ingress tagged packets, D-Link Smart Switches will refer to these information and prioritize them with 4 different priority queues. If 802.1p is enabled.
OBJECT-TYPE    
  INTEGER 0..7  

qosUserPriClass 1.3.6.1.4.1.171.10.75.14.12.5.1.1.2
The User Class the received frame is mapped to.
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosPriSettings 1.3.6.1.4.1.171.10.75.14.12.7
OBJECT IDENTIFIER    

qosPriSettingsTable 1.3.6.1.4.1.171.10.75.14.12.7.1
A list of port priority settings.
OBJECT-TYPE    
  SEQUENCE OF  
    QosPriSettingsEntry

qosPriSettingsEntry 1.3.6.1.4.1.171.10.75.14.12.7.1.1
A list of port priority settings Entries.
OBJECT-TYPE    
  QosPriSettingsEntry  

qosPriSetPortIndex 1.3.6.1.4.1.171.10.75.14.12.7.1.1.1
A port identifier that is in the range of 1 to ifNumber.
OBJECT-TYPE    
  INTEGER  

qosPriSetPortType 1.3.6.1.4.1.171.10.75.14.12.7.1.1.2
The port priority setting type. (ex. none = 0, port mapping = 1, 802.1p = 2, DSCP = 4. If you want enable 802.1p & DSCP, the value is 2 + 4 = 6.
OBJECT-TYPE    
  INTEGER 0..7  

qosDiffServ 1.3.6.1.4.1.171.10.75.14.12.6
OBJECT IDENTIFIER    

qosDiffServTypeGroup 1.3.6.1.4.1.171.10.75.14.12.6.1
OBJECT IDENTIFIER    

qosDiffServType00 1.3.6.1.4.1.171.10.75.14.12.6.1.1
DiffServ Type 0 : IP ToS value = 0
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType01 1.3.6.1.4.1.171.10.75.14.12.6.1.2
DiffServ Type 01 : IP ToS value = 4
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType02 1.3.6.1.4.1.171.10.75.14.12.6.1.3
DiffServ Type 02 : IP ToS value = 8
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType03 1.3.6.1.4.1.171.10.75.14.12.6.1.4
DiffServ Type 03 : IP ToS value = 12
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType04 1.3.6.1.4.1.171.10.75.14.12.6.1.5
DiffServ Type 04 : IP ToS value = 16
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType05 1.3.6.1.4.1.171.10.75.14.12.6.1.6
DiffServ Type 05 : IP ToS value = 20
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType06 1.3.6.1.4.1.171.10.75.14.12.6.1.7
DiffServ Type 06 : IP ToS value = 24
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType07 1.3.6.1.4.1.171.10.75.14.12.6.1.8
DiffServ Type 07 : IP ToS value = 28
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType08 1.3.6.1.4.1.171.10.75.14.12.6.1.9
DiffServ Type 08 : IP ToS value = 32
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType09 1.3.6.1.4.1.171.10.75.14.12.6.1.10
DiffServ Type 09 : IP ToS value = 36
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType10 1.3.6.1.4.1.171.10.75.14.12.6.1.11
DiffServ Type 10 : IP ToS value = 40
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType11 1.3.6.1.4.1.171.10.75.14.12.6.1.12
DiffServ Type 11 : IP ToS value = 44
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType12 1.3.6.1.4.1.171.10.75.14.12.6.1.13
DiffServ Type 12 : IP ToS value = 48
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType13 1.3.6.1.4.1.171.10.75.14.12.6.1.14
DiffServ Type 13 : IP ToS value = 52
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType14 1.3.6.1.4.1.171.10.75.14.12.6.1.15
DiffServ Type 14 : IP ToS value = 56
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType15 1.3.6.1.4.1.171.10.75.14.12.6.1.16
DiffServ Type 15 : IP ToS value = 60
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType16 1.3.6.1.4.1.171.10.75.14.12.6.1.17
DiffServ Type 16 : IP ToS value = 64
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType17 1.3.6.1.4.1.171.10.75.14.12.6.1.18
DiffServ Type 17 : IP ToS value = 68
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType18 1.3.6.1.4.1.171.10.75.14.12.6.1.19
DiffServ Type 18 : IP ToS value = 72
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType19 1.3.6.1.4.1.171.10.75.14.12.6.1.20
DiffServ Type 19 : IP ToS value = 76
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType20 1.3.6.1.4.1.171.10.75.14.12.6.1.21
DiffServ Type 20 : IP ToS value = 80
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType21 1.3.6.1.4.1.171.10.75.14.12.6.1.22
DiffServ Type 21 : IP ToS value = 84
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType22 1.3.6.1.4.1.171.10.75.14.12.6.1.23
DiffServ Type 22 : IP ToS value = 88
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType23 1.3.6.1.4.1.171.10.75.14.12.6.1.24
DiffServ Type 23 : IP ToS value = 92
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType24 1.3.6.1.4.1.171.10.75.14.12.6.1.25
DiffServ Type 24 : IP ToS value = 96
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType25 1.3.6.1.4.1.171.10.75.14.12.6.1.26
DiffServ Type 25 : IP ToS value = 100
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType26 1.3.6.1.4.1.171.10.75.14.12.6.1.27
DiffServ Type 26 : IP ToS value = 104
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType27 1.3.6.1.4.1.171.10.75.14.12.6.1.28
DiffServ Type 27 : IP ToS value = 108
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType28 1.3.6.1.4.1.171.10.75.14.12.6.1.29
DiffServ Type 28 : IP ToS value = 112
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType29 1.3.6.1.4.1.171.10.75.14.12.6.1.30
DiffServ Type 29 : IP ToS value = 116
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType30 1.3.6.1.4.1.171.10.75.14.12.6.1.31
DiffServ Type 30 : IP ToS value = 120
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType31 1.3.6.1.4.1.171.10.75.14.12.6.1.32
DiffServ Type 31 : IP ToS value = 124
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType32 1.3.6.1.4.1.171.10.75.14.12.6.1.33
DiffServ Type 32 : IP ToS value = 128
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType33 1.3.6.1.4.1.171.10.75.14.12.6.1.34
DiffServ Type 33 : IP ToS value = 132
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType34 1.3.6.1.4.1.171.10.75.14.12.6.1.35
DiffServ Type 34 : IP ToS value = 136
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType35 1.3.6.1.4.1.171.10.75.14.12.6.1.36
DiffServ Type 35 : IP ToS value = 140
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType36 1.3.6.1.4.1.171.10.75.14.12.6.1.37
DiffServ Type 36 : IP ToS value = 144
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType37 1.3.6.1.4.1.171.10.75.14.12.6.1.38
DiffServ Type 37 : IP ToS value = 148
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType38 1.3.6.1.4.1.171.10.75.14.12.6.1.39
DiffServ Type 38 : IP ToS value = 152
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType39 1.3.6.1.4.1.171.10.75.14.12.6.1.40
DiffServ Type 39 : IP ToS value = 156
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType40 1.3.6.1.4.1.171.10.75.14.12.6.1.41
DiffServ Type 40 : IP ToS value = 160
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType41 1.3.6.1.4.1.171.10.75.14.12.6.1.42
DiffServ Type 41 : IP ToS value = 164
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType42 1.3.6.1.4.1.171.10.75.14.12.6.1.43
DiffServ Type 42 : IP ToS value = 168
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType43 1.3.6.1.4.1.171.10.75.14.12.6.1.44
DiffServ Type 43 : IP ToS value = 172
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType44 1.3.6.1.4.1.171.10.75.14.12.6.1.45
DiffServ Type 44 : IP ToS value = 176
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType45 1.3.6.1.4.1.171.10.75.14.12.6.1.46
DiffServ Type 45 : IP ToS value = 180
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType46 1.3.6.1.4.1.171.10.75.14.12.6.1.47
DiffServ Type 46 : IP ToS value = 184
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType47 1.3.6.1.4.1.171.10.75.14.12.6.1.48
DiffServ Type 47 : IP ToS value = 188
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType48 1.3.6.1.4.1.171.10.75.14.12.6.1.49
DiffServ Type 48 : IP ToS value = 192
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType49 1.3.6.1.4.1.171.10.75.14.12.6.1.50
DiffServ Type 49 : IP ToS value = 196
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType50 1.3.6.1.4.1.171.10.75.14.12.6.1.51
DiffServ Type 50 : IP ToS value = 200
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType51 1.3.6.1.4.1.171.10.75.14.12.6.1.52
DiffServ Type 51 : IP ToS value = 204
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType52 1.3.6.1.4.1.171.10.75.14.12.6.1.53
DiffServ Type 52 : IP ToS value = 208
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType53 1.3.6.1.4.1.171.10.75.14.12.6.1.54
DiffServ Type 53 : IP ToS value = 212
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType54 1.3.6.1.4.1.171.10.75.14.12.6.1.55
DiffServ Type 54 : IP ToS value = 216
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType55 1.3.6.1.4.1.171.10.75.14.12.6.1.56
DiffServ Type 55 : IP ToS value = 220
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType56 1.3.6.1.4.1.171.10.75.14.12.6.1.57
DiffServ Type 56 : IP ToS value = 224
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType57 1.3.6.1.4.1.171.10.75.14.12.6.1.58
DiffServ Type 57 : IP ToS value = 228
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType58 1.3.6.1.4.1.171.10.75.14.12.6.1.59
DiffServ Type 58 : IP ToS value = 232
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType59 1.3.6.1.4.1.171.10.75.14.12.6.1.60
DiffServ Type 59 : IP ToS value = 236
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType60 1.3.6.1.4.1.171.10.75.14.12.6.1.61
DiffServ Type 60 : IP ToS value = 240
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType61 1.3.6.1.4.1.171.10.75.14.12.6.1.62
DiffServ Type 61 : IP ToS value = 244
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType62 1.3.6.1.4.1.171.10.75.14.12.6.1.63
DiffServ Type 62 : IP ToS value = 248
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosDiffServType63 1.3.6.1.4.1.171.10.75.14.12.6.1.64
DiffServ Type 63 : IP ToS value = 252
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), highest(3)  

qosAclPrioritySettings 1.3.6.1.4.1.171.10.75.14.12.8
OBJECT IDENTIFIER    

aclQosTable 1.3.6.1.4.1.171.10.75.14.12.8.1
A list of priority by acl setting.
OBJECT-TYPE    
  SEQUENCE OF  
    AclQosEntry

aclQosEntry 1.3.6.1.4.1.171.10.75.14.12.8.1.1
A list of priority by acl setting entry.
OBJECT-TYPE    
  AclQosEntry  

aclQosIndex 1.3.6.1.4.1.171.10.75.14.12.8.1.1.1
Index of priority by acl setting.
OBJECT-TYPE    
  Integer32 1..65535  

aclQosType 1.3.6.1.4.1.171.10.75.14.12.8.1.1.2
Type of priority by acl setting.
OBJECT-TYPE    
  INTEGER mac(0), ip(1), tcp(2), udp(3), vlanid(4), protocol(5)  

aclQosMACAddr 1.3.6.1.4.1.171.10.75.14.12.8.1.1.3
Dst MAC of priority by acl setting.
OBJECT-TYPE    
  MacAddress  

aclQosIPAddr 1.3.6.1.4.1.171.10.75.14.12.8.1.1.4
Dst IP of priority by acl setting
OBJECT-TYPE    
  IpAddress  

aclQosTCPUDPPort 1.3.6.1.4.1.171.10.75.14.12.8.1.1.5
Dst TCP/UDP port of priority by acl setting
OBJECT-TYPE    
  Integer32 1..65535  

aclQosVlanID 1.3.6.1.4.1.171.10.75.14.12.8.1.1.6
VLAN ID of priority by acl setting
OBJECT-TYPE    
  Integer32 1..4094  

aclQosProtocol 1.3.6.1.4.1.171.10.75.14.12.8.1.1.7
Ip protocol number of priority by acl setting
OBJECT-TYPE    
  Integer32 1..255  

aclQosAssignClass 1.3.6.1.4.1.171.10.75.14.12.8.1.1.8
Be mapped class of priority by acl setting.
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

aclQosStatus 1.3.6.1.4.1.171.10.75.14.12.8.1.1.9
Status of priority by acl setting.
OBJECT-TYPE    
  RowStatus  

bandwidthCtrlSettings 1.3.6.1.4.1.171.10.75.14.13.1
OBJECT IDENTIFIER    

bandwidthCtrlTable 1.3.6.1.4.1.171.10.75.14.13.1.2
A table to control the rate limiting parameters either for the entire switch or for each interface in the switch.
OBJECT-TYPE    
  SEQUENCE OF  
    BandwidthCtrlEntry

bandwidthCtrlEntry 1.3.6.1.4.1.171.10.75.14.13.1.2.1
An entry appears in this table for each physical interface in the switch.
OBJECT-TYPE    
  BandwidthCtrlEntry  

bandwidthCtrlIndex 1.3.6.1.4.1.171.10.75.14.13.1.2.1.1
The interface index for which the configuration in this entry applies.
OBJECT-TYPE    
  Integer32  

bandwidthCtrlTxThreshold 1.3.6.1.4.1.171.10.75.14.13.1.2.1.2
Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000 (Kbits per second) in GE port. (Note: The multiple of 1850 Kbits/sec will be set automatically because the resolution of Giga-port Tx bandwidth control is 1850 Kbits/sec.)
OBJECT-TYPE    
  Integer32 0 | 64..1024000  

bandwidthCtrlRxThreshold 1.3.6.1.4.1.171.10.75.14.13.1.2.1.3
Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets on this interface. The value that can be set for this object is limited by the underlying hardware. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000(Kbits per second) in GE port.
OBJECT-TYPE    
  Integer32 0 | 64..1024000  

broadcastStormCtrlSettings 1.3.6.1.4.1.171.10.75.14.13.3
OBJECT IDENTIFIER    

broadcastStormCtrlGlobalOnOff 1.3.6.1.4.1.171.10.75.14.13.3.1
This object indicates storm control function is enabled or disabled for device. When you enable broadcast storm control function, D-Link Smart Switches will allowed you to limit the number of broadcast packets per second going through device.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

broadcastStormCtrlLimitType 1.3.6.1.4.1.171.10.75.14.13.3.2
This object indicates storm control function is control broadcast packet or multicast packet or dlf packet.
OBJECT-TYPE    
  INTEGER broadcastonly(1), multicastAndbroadcast(2), dlfMulticastAndbroadcast(3)  

broadcastStormCtrlThreshold 1.3.6.1.4.1.171.10.75.14.13.3.3
Allows to configure the limiting value for the maximum number of Kbits/sec that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting on this interface. The value that can be set for this object is limited by the underlying hardware. The limit value must be between 64~1024000 and limit value is multiple of 64. (Notice : if the limit value is 0, it means unlimited.)
OBJECT-TYPE    
  Integer32 0 | 64..1024000  

trafficCtrlSettings 1.3.6.1.4.1.171.10.75.14.13.4
OBJECT IDENTIFIER    

trafficCtrlTrap 1.3.6.1.4.1.171.10.75.14.13.4.1
The trap setting of traffic control.
OBJECT-TYPE    
  INTEGER none(0), stormOccurred(1), stormCleared(2), both(3)  

trafficCtrlTable 1.3.6.1.4.1.171.10.75.14.13.4.2
The traffic control table.
OBJECT-TYPE    
  SEQUENCE OF  
    TrafficCtrlEntry

trafficCtrlEntry 1.3.6.1.4.1.171.10.75.14.13.4.2.1
The traffic control entry.
OBJECT-TYPE    
  TrafficCtrlEntry  

trafficCtrlIndex 1.3.6.1.4.1.171.10.75.14.13.4.2.1.1
The traffic control index.
OBJECT-TYPE    
  Integer32 1..65535  

trafficCtrlActionMode 1.3.6.1.4.1.171.10.75.14.13.4.2.1.2
The action mode of traffic control.
OBJECT-TYPE    
  INTEGER drop(0), shutdown(1)  

trafficCtrlType 1.3.6.1.4.1.171.10.75.14.13.4.2.1.3
The control type of traffic control. (b: Broadcast, m: Multicast, u: Unknown Unicast)
OBJECT-TYPE    
  INTEGER none(0), b(1), m(2), mb(3), u(4), ub(5), um(6), umb(7)  

trafficCtrlThreshold 1.3.6.1.4.1.171.10.75.14.13.4.2.1.4
The threshold of traffic control.
OBJECT-TYPE    
  Integer32 1..102400  

trafficCtrlCountDown 1.3.6.1.4.1.171.10.75.14.13.4.2.1.5
The count down value of traffic control.
OBJECT-TYPE    
  Integer32 0..30  

trafficCtrlTimeInterval 1.3.6.1.4.1.171.10.75.14.13.4.2.1.6
The time interval of traffic control.
OBJECT-TYPE    
  Integer32 5..30  

securityTrustedHost 1.3.6.1.4.1.171.10.75.14.14.1
OBJECT IDENTIFIER    

trustedHostStatus 1.3.6.1.4.1.171.10.75.14.14.1.1
This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which you trust to access and control the switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

trustedHostTable 1.3.6.1.4.1.171.10.75.14.14.1.2
A table to configure trusted host in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    TrustedHostEntry

trustedHostEntry 1.3.6.1.4.1.171.10.75.14.14.1.2.1
Each entry in this table represents rules for particular trusted host.
OBJECT-TYPE    
  TrustedHostEntry  

trustedHostIpAddr 1.3.6.1.4.1.171.10.75.14.14.1.2.1.1
The IP address of host you allow to access to D-Link Smart Switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.
OBJECT-TYPE    
  IpAddress  

trustedHostIpMask 1.3.6.1.4.1.171.10.75.14.14.1.2.1.2
Used to mask with IP address, it allow you set a subnet as a trusted host entry.
OBJECT-TYPE    
  IpAddress  

trustedHostRowStatus 1.3.6.1.4.1.171.10.75.14.14.1.2.1.3
The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
OBJECT-TYPE    
  RowStatus  

securityARPSpoofPrevent 1.3.6.1.4.1.171.10.75.14.14.3
OBJECT IDENTIFIER    

aRPSpoofPreventTable 1.3.6.1.4.1.171.10.75.14.14.3.1
A table to control ARP Spoofing prevention for the entire switch or for each interface in the switch.
OBJECT-TYPE    
  SEQUENCE OF  
    ARPSpoofPreventEntry

aRPSpoofPreventEntry 1.3.6.1.4.1.171.10.75.14.14.3.1.1
An entry appears in this table for each interface in the system.
OBJECT-TYPE    
  ARPSpoofPreventEntry  

aRPSpoofPreventIpAddr 1.3.6.1.4.1.171.10.75.14.14.3.1.1.1
Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.
OBJECT-TYPE    
  IpAddress  

aRPSpoofPreventMacAddress 1.3.6.1.4.1.171.10.75.14.14.3.1.1.2
Ethernet Mac Address.
OBJECT-TYPE    
  MacAddress  

aRPSpoofPreventPortList 1.3.6.1.4.1.171.10.75.14.14.3.1.1.3
Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.
OBJECT-TYPE    
  PortList  

aRPSpoofPreventRowStatus 1.3.6.1.4.1.171.10.75.14.14.3.1.1.4
This object indicates the status of this entry.
OBJECT-TYPE    
  RowStatus  

securitySSL 1.3.6.1.4.1.171.10.75.14.14.5
OBJECT IDENTIFIER    

sslSecurityHttpStatus 1.3.6.1.4.1.171.10.75.14.14.5.1
This object is for enabling or disabling secure HTTP in the system.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sslCiphers 1.3.6.1.4.1.171.10.75.14.14.5.2
OBJECT IDENTIFIER    

sslCipherSuiteList 1.3.6.1.4.1.171.10.75.14.14.5.2.1
This object is to configure the cipher-suites list.
OBJECT-TYPE    
  BITS rsa-null-md5(0), rsa-null-sha(1), rsa-des-sha(2), rsa-3des-sha(3), dh-rsa-des-sha(4), dh-rsa-3des-sha(5), rsa-exp1024-des-sha(6)  

securitySSH 1.3.6.1.4.1.171.10.75.14.14.8
OBJECT IDENTIFIER    

sshSecurityStatus 1.3.6.1.4.1.171.10.75.14.14.8.1
This object is for enabling or disabling ssh in the system.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sshMaxAuthFailAttempts 1.3.6.1.4.1.171.10.75.14.14.8.2
This object indicates the max auth fail retry attempt times.
OBJECT-TYPE    
  INTEGER 2..20  

sshSessionKeyRekeying 1.3.6.1.4.1.171.10.75.14.14.8.3
This object indicates one SSH session rekey time interval.
OBJECT-TYPE    
  INTEGER never(0), ten-min(10), thirty-min(30), sixty-min(60)  

sshMaxSession 1.3.6.1.4.1.171.10.75.14.14.8.4
This object indicates max SSH session number supported in system.
OBJECT-TYPE    
  INTEGER 1..8  

sshConnectionTimeout 1.3.6.1.4.1.171.10.75.14.14.8.5
This object indicates SSH connection timeout value.
OBJECT-TYPE    
  INTEGER 120..600  

sshAuthenMethodPassWordAdmin 1.3.6.1.4.1.171.10.75.14.14.8.6
The object indicates authen method password is enabled or disabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sshAuthenMethodPubKeyAdmin 1.3.6.1.4.1.171.10.75.14.14.8.7
The object indicates authen method public-key is enabled or disabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sshAuthenMethodHostKeyAdmin 1.3.6.1.4.1.171.10.75.14.14.8.8
The object indicates authen method host-key is enabled or disabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sshCipherSuiteList 1.3.6.1.4.1.171.10.75.14.14.8.9
This object is to configure the cipher-suites list.
OBJECT-TYPE    
  BITS tripleDESCBC(0), dESCBC(1)  

sshMacSuiteList 1.3.6.1.4.1.171.10.75.14.14.8.10
This object is to configure the MAC-list.
OBJECT-TYPE    
  BITS hMAC-SHA1(0), hMAC-MD5(1)  

sshPublKeyRSAAdmin 1.3.6.1.4.1.171.10.75.14.14.8.11
The object indicates Public key generating algorithm RSA is enabled or disabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sshUserInfoTable 1.3.6.1.4.1.171.10.75.14.14.8.12
A table to configure SSH user auth in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    SshUserInfoEntry

sshUserInfoEntry 1.3.6.1.4.1.171.10.75.14.14.8.12.1
An entry to configure user auth in the system.
OBJECT-TYPE    
  SshUserInfoEntry  

sshUserInfoID 1.3.6.1.4.1.171.10.75.14.14.8.12.1.1
The Schedule identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 8.
OBJECT-TYPE    
  Integer32 1..8  

sshUserInfoUserName 1.3.6.1.4.1.171.10.75.14.14.8.12.1.2
The ssh user name associated with the SSH suer Info. entry (e.g., `admin, user').
OBJECT-TYPE    
  DisplayString Size(1..20)  

sshUserInfoAuth 1.3.6.1.4.1.171.10.75.14.14.8.12.1.3
The object indicates which auth used by the user.
OBJECT-TYPE    
  INTEGER publickey(4), password(2), hostbased(1)  

sshUserInfoHostName 1.3.6.1.4.1.171.10.75.14.14.8.12.1.4
The ssh host name associated with the SSH suer Info. entry (e.g., `DUT1, DUT2').
OBJECT-TYPE    
  DisplayString Size(1..20)  

sshUserInfoHostIp 1.3.6.1.4.1.171.10.75.14.14.8.12.1.5
SSH HostBased IP Address of the system.
OBJECT-TYPE    
  IpAddress  

securityPortSecurity 1.3.6.1.4.1.171.10.75.14.14.2
OBJECT IDENTIFIER    

portSecTable 1.3.6.1.4.1.171.10.75.14.14.2.1
A table to control port security features of the device.
OBJECT-TYPE    
  SEQUENCE OF  
    PortSecEntry

portSecEntry 1.3.6.1.4.1.171.10.75.14.14.2.1.1
An entry appears in port security table for each interface in the system.
OBJECT-TYPE    
  PortSecEntry  

portSecIndex 1.3.6.1.4.1.171.10.75.14.14.2.1.1.1
The interface index for which the configuration in this entry applies.
OBJECT-TYPE    
  Integer32  

portSecState 1.3.6.1.4.1.171.10.75.14.14.2.1.1.2
Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port security admin state is enabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

portSecMLA 1.3.6.1.4.1.171.10.75.14.14.2.1.1.3
Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number. The number can be set 0 to 64. Note: Set value 0 means cannot learn MAC address.
OBJECT-TYPE    
  Integer32 0..64  

portSecLockAddrMode 1.3.6.1.4.1.171.10.75.14.14.2.1.1.4
Configures port security lock address mode for the interface. deleteOnReset : The locked addresses will not age out until the Switch has been reset. deleteOnTimeout : The locked addresses will age out after the aging timer expires. Permanent : The locked addresses will not age out after the aging timer expires.
OBJECT-TYPE    
  INTEGER deleteOnReset(1), deleteOnTimeout(2), permanent(3)  

portSecFDBPermanentTable 1.3.6.1.4.1.171.10.75.14.14.2.2
A table to control port security FDB Permanent of the device.
OBJECT-TYPE    
  SEQUENCE OF  
    PortSecFDBPermanentEntry

portSecFDBPermanentEntry 1.3.6.1.4.1.171.10.75.14.14.2.2.1
An entry appears in port security table for each interface in the system.
OBJECT-TYPE    
  PortSecFDBPermanentEntry  

portSecFDBPermIndex 1.3.6.1.4.1.171.10.75.14.14.2.2.1.1
The index of the port security MAC entry.
OBJECT-TYPE    
  INTEGER  

portSecFDBPermVlanID 1.3.6.1.4.1.171.10.75.14.14.2.2.1.2
The VLAN ID of the port security MAC entry.
OBJECT-TYPE    
  INTEGER  

portSecFDBPermMac 1.3.6.1.4.1.171.10.75.14.14.2.2.1.3
The MAC address associated of the port security MAC entry.
OBJECT-TYPE    
  MacAddress  

portSecFDBPermPort 1.3.6.1.4.1.171.10.75.14.14.2.2.1.4
The forwarding port of the port security MAC entry.
OBJECT-TYPE    
  INTEGER  

aclProfile 1.3.6.1.4.1.171.10.75.14.15.1
OBJECT IDENTIFIER    

aclProfileTable 1.3.6.1.4.1.171.10.75.14.15.1.1
A table to ACL profile .
OBJECT-TYPE    
  SEQUENCE OF  
    AclProfileEntry

aclProfileEntry 1.3.6.1.4.1.171.10.75.14.15.1.1.1
Each entry in this table is a ACL profile. Index to the table is ACL profile ID.
OBJECT-TYPE    
  AclProfileEntry  

aclProfileNo 1.3.6.1.4.1.171.10.75.14.15.1.1.1.1
The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only.
OBJECT-TYPE    
  Integer32 1..50  

aclProfileType 1.3.6.1.4.1.171.10.75.14.15.1.1.1.2
The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, arpSP-permit(4) - for ARP Spoofing prevention entry, arpSP-deny(5) - for ARP Spoofing prevention entry, voiceVlan(6) - for Voice VLAN OUI entry. Note that only l2 and l3 could be set by user, other is reserved for system to show information.
OBJECT-TYPE    
  INTEGER l2(1), l3(2), arpSP-permit(4), arpSP-deny(5), voiceVlan(6)  

aclProfileRuleCount 1.3.6.1.4.1.171.10.75.14.15.1.1.1.3
The number of rules in this profile.
OBJECT-TYPE    
  Integer32 0..65535  

aclProfileMask 1.3.6.1.4.1.171.10.75.14.15.1.1.1.4
Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST-MAC 0 (LSB) L2 SRC-MAC 1 L2 VID 2 L2 8021P-PRIORITY 3 L2 ETHER-TYPE 4 L3 DSCP 5 L3 ICMP-TYPE 6 L3 ICMP-CODE 7 L3 IGMP-TYPE 8 L3 DST-IP 9 L3 SRC-IP 10 L3 DST-PORT 11 L3 SRC-PORT 12 L3 TCPFLAG 13 ARP-SP ARP-SENDER-MAC 14 ARP-SP ARP-SENDER-IP 15 (MSB) ------------------------------------------- The value is in Hex format.
OBJECT-TYPE    
  OCTET STRING  

aclProfileDstMacAddrMask 1.3.6.1.4.1.171.10.75.14.15.1.1.1.5
The ACL Profile destination MAC address mask. If DST-MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate a range of MAC address which is really care.
OBJECT-TYPE    
  MacAddress  

aclProfileSrcMacAddrMask 1.3.6.1.4.1.171.10.75.14.15.1.1.1.6
The ACL Profile source MAC address mask. If SRC-MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.
OBJECT-TYPE    
  MacAddress  

aclProfileIPProtocol 1.3.6.1.4.1.171.10.75.14.15.1.1.1.7
Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none.
OBJECT-TYPE    
  INTEGER none(0), icmp(1), igmp(2), tcp(6), udp(17), ipMask(255)  

aclProfileIPProtocolMask 1.3.6.1.4.1.171.10.75.14.15.1.1.1.8
The ACL Profile IP protocol mask. If aclProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.
OBJECT-TYPE    
  OCTET STRING  

aclProfileDstIpAddrMask 1.3.6.1.4.1.171.10.75.14.15.1.1.1.9
The ACL Profile destination IP address mask. If DST-IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
OBJECT-TYPE    
  IpAddress  

aclProfileSrcIpAddrMask 1.3.6.1.4.1.171.10.75.14.15.1.1.1.10
The ACL Profile source IP address mask. If SRC-IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
OBJECT-TYPE    
  IpAddress  

aclProfileDstPortMask 1.3.6.1.4.1.171.10.75.14.15.1.1.1.11
The ACL Profile UDP/TCP destination port mask. If DST-PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format.
OBJECT-TYPE    
  OCTET STRING  

aclProfileSrcPortMask 1.3.6.1.4.1.171.10.75.14.15.1.1.1.12
The ACL Profile UDP/TCP source port mask. If SRC-PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format.
OBJECT-TYPE    
  OCTET STRING  

aclProfileArpSenderMacAddrMask 1.3.6.1.4.1.171.10.75.14.15.1.1.1.13
The ACL Profile Sender MAC mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.
OBJECT-TYPE    
  MacAddress  

aclProfileArpSenderIpAddrMask 1.3.6.1.4.1.171.10.75.14.15.1.1.1.14
The ACL Profile Sender IP mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.
OBJECT-TYPE    
  IpAddress  

aclProfileStatus 1.3.6.1.4.1.171.10.75.14.15.1.1.1.15
This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of aclProfileType, aclProfileMask and ProtocolType are not conflicted.
OBJECT-TYPE    
  RowStatus  

aclL2Rule 1.3.6.1.4.1.171.10.75.14.15.2
OBJECT IDENTIFIER    

aclL2RuleTable 1.3.6.1.4.1.171.10.75.14.15.2.1
A table to configure L2 filter rules in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    AclL2RuleEntry

aclL2RuleEntry 1.3.6.1.4.1.171.10.75.14.15.2.1.1
Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID.
OBJECT-TYPE    
  AclL2RuleEntry  

aclL2AccessID 1.3.6.1.4.1.171.10.75.14.15.2.1.1.1
L2 Filter rule ID.
OBJECT-TYPE    
  Integer32 1..65535  

aclL2ProfileID 1.3.6.1.4.1.171.10.75.14.15.2.1.1.2
ACL Profile ID which this rule join.
OBJECT-TYPE    
  Integer32 1..50  

aclL2RuleEtherType 1.3.6.1.4.1.171.10.75.14.15.2.1.1.3
The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1 | 1501..65535  

aclL2RuleDstMacAddr 1.3.6.1.4.1.171.10.75.14.15.2.1.1.4
Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition.
OBJECT-TYPE    
  MacAddress  

aclL2RuleSrcMacAddr 1.3.6.1.4.1.171.10.75.14.15.2.1.1.5
Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address
OBJECT-TYPE    
  MacAddress  

aclL2RuleVlanId 1.3.6.1.4.1.171.10.75.14.15.2.1.1.6
Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1..4094  

aclL2Rule1pPriority 1.3.6.1.4.1.171.10.75.14.15.2.1.1.7
802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1..7  

aclL2RuleDstMacAddrMask 1.3.6.1.4.1.171.10.75.14.15.2.1.1.8
The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting.
OBJECT-TYPE    
  MacAddress  

aclL2RuleSrcMacAddrMask 1.3.6.1.4.1.171.10.75.14.15.2.1.1.9
The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting.
OBJECT-TYPE    
  MacAddress  

aclL2RuleInPortList 1.3.6.1.4.1.171.10.75.14.15.2.1.1.10
Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list.
OBJECT-TYPE    
  PortList  

aclL2RuleAction 1.3.6.1.4.1.171.10.75.14.15.2.1.1.11
Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded.
OBJECT-TYPE    
  INTEGER allow(1), drop(2), mirror(3), rateLimit(4), replaceDSCP(5)  

aclL2RuleRateLimit 1.3.6.1.4.1.171.10.75.14.15.2.1.1.12
Rate limit for matched packet.
OBJECT-TYPE    
  Unsigned32  

aclL2RuleReplaceDSCP 1.3.6.1.4.1.171.10.75.14.15.2.1.1.13
Replace DSCP for matched packet.
OBJECT-TYPE    
  Integer32 -1..63  

aclL2RuleStatus 1.3.6.1.4.1.171.10.75.14.15.2.1.1.14
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
OBJECT-TYPE    
  RowStatus  

aclL3Rule 1.3.6.1.4.1.171.10.75.14.15.3
OBJECT IDENTIFIER    

aclL3RuleTable 1.3.6.1.4.1.171.10.75.14.15.3.1
A table to configure L3 filter rules in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    AclL3RuleEntry

aclL3RuleEntry 1.3.6.1.4.1.171.10.75.14.15.3.1.1
Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID.
OBJECT-TYPE    
  AclL3RuleEntry  

aclL3RuleAccessID 1.3.6.1.4.1.171.10.75.14.15.3.1.1.1
L3 Filter rule ID.
OBJECT-TYPE    
  Integer32 1..65535  

aclL3RuleProfileNo 1.3.6.1.4.1.171.10.75.14.15.3.1.1.2
The Profile ID which this rule join.
OBJECT-TYPE    
  Integer32 1..50  

aclL3RuleProtocol 1.3.6.1.4.1.171.10.75.14.15.3.1.1.3
The type of protocol to be checked against the packet.
OBJECT-TYPE    
  INTEGER icmp(1), igmp(2), tcp(6), udp(17)  

aclL3RuleProtocolMask 1.3.6.1.4.1.171.10.75.14.15.3.1.1.4
The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.
OBJECT-TYPE    
  OCTET STRING  

aclL3RuleICMPMessageType 1.3.6.1.4.1.171.10.75.14.15.3.1.1.5
The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18),
OBJECT-TYPE    
  Integer32 -1..255  

aclL3RuleICMPMessageCode 1.3.6.1.4.1.171.10.75.14.15.3.1.1.6
The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12),
OBJECT-TYPE    
  Integer32 -1..255  

aclL3RuleDstIpAddr 1.3.6.1.4.1.171.10.75.14.15.3.1.1.7
Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
OBJECT-TYPE    
  IpAddress  

aclL3RuleSrcIpAddr 1.3.6.1.4.1.171.10.75.14.15.3.1.1.8
Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
OBJECT-TYPE    
  IpAddress  

aclL3RuleDstIpAddrMask 1.3.6.1.4.1.171.10.75.14.15.3.1.1.9
The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting.
OBJECT-TYPE    
  IpAddress  

aclL3RuleSrcIpAddrMask 1.3.6.1.4.1.171.10.75.14.15.3.1.1.10
The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting.
OBJECT-TYPE    
  IpAddress  

aclL3RuleTcpUdpDstPort 1.3.6.1.4.1.171.10.75.14.15.3.1.1.11
The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1..65535  

aclL3RuleTcpUdpSrcPort 1.3.6.1.4.1.171.10.75.14.15.3.1.1.12
The TCP / UDP source port. The default value is -1, which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1..65535  

aclL3RuleTcpUdpDstPortMask 1.3.6.1.4.1.171.10.75.14.15.3.1.1.13
The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting.
OBJECT-TYPE    
  OCTET STRING  

aclL3RuleTcpUdpSrcPortMask 1.3.6.1.4.1.171.10.75.14.15.3.1.1.14
The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting.
OBJECT-TYPE    
  OCTET STRING  

aclL3RuleTcpAckBit 1.3.6.1.4.1.171.10.75.14.15.3.1.1.15
The TCP ACK bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition.
OBJECT-TYPE    
  INTEGER dont-care(-1), establish(1), notEstablish(2)  

aclL3RuleTcpRstBit 1.3.6.1.4.1.171.10.75.14.15.3.1.1.16
The TCP RST bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition.
OBJECT-TYPE    
  INTEGER dont-care(-1), establish(1), notEstablish(2)  

aclL3RuleTcpUrgBit 1.3.6.1.4.1.171.10.75.14.15.3.1.1.17
The TCP Urg bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition.
OBJECT-TYPE    
  INTEGER dont-care(-1), establish(1), notEstablish(2)  

aclL3RuleTcpPshBit 1.3.6.1.4.1.171.10.75.14.15.3.1.1.18
The TCP Psh bit to be checked against the packet. The default value is 'dont-care'(-1). which means the rule don't care this condition.
OBJECT-TYPE    
  INTEGER dont-care(-1), establish(1), notEstablish(2)  

aclL3RuleTcpSynBit 1.3.6.1.4.1.171.10.75.14.15.3.1.1.19
The TCP Syn bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition.
OBJECT-TYPE    
  INTEGER dont-care(-1), establish(1), notEstablish(2)  

aclL3RuleTcpFinBit 1.3.6.1.4.1.171.10.75.14.15.3.1.1.20
The TCP Fin bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition.
OBJECT-TYPE    
  INTEGER dont-care(-1), establish(1), notEstablish(2)  

aclL3RuleDscp 1.3.6.1.4.1.171.10.75.14.15.3.1.1.21
The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1..63  

aclL3RuleIgmpType 1.3.6.1.4.1.171.10.75.14.15.3.1.1.22
The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1..255  

aclL3RulePortList 1.3.6.1.4.1.171.10.75.14.15.3.1.1.23
Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable.
OBJECT-TYPE    
  PortList  

aclL3RuleAction 1.3.6.1.4.1.171.10.75.14.15.3.1.1.24
Specifies the action to be taken on the packet if the filter rule matches.
OBJECT-TYPE    
  INTEGER allow(1), drop(2), mirror(3), rateLimit(4), replaceDSCP(5)  

aclL3RuleRateLimit 1.3.6.1.4.1.171.10.75.14.15.3.1.1.25
Rate limit for matched packet.
OBJECT-TYPE    
  Unsigned32  

aclL3RuleReplaceDSCP 1.3.6.1.4.1.171.10.75.14.15.3.1.1.26
ReplaceDSCP for matched packet.
OBJECT-TYPE    
  Integer32 -1..63  

aclL3RuleStatus 1.3.6.1.4.1.171.10.75.14.15.3.1.1.27
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
OBJECT-TYPE    
  RowStatus  

cpuFilterProfile 1.3.6.1.4.1.171.10.75.14.33.1
OBJECT IDENTIFIER    

cpuFilterProfileTable 1.3.6.1.4.1.171.10.75.14.33.1.1
A table to CPUInterfaceFilter profile .
OBJECT-TYPE    
  SEQUENCE OF  
    CpuFilterProfileEntry

cpuFilterProfileEntry 1.3.6.1.4.1.171.10.75.14.33.1.1.1
Each entry in this table is a CPUInterfaceFilter profile. Index to the table is CPUInterfaceFilter profile ID.
OBJECT-TYPE    
  CpuFilterProfileEntry  

cpuFilterProfileNo 1.3.6.1.4.1.171.10.75.14.33.1.1.1.1
The CPUInterfaceFilter Profile ID. The ID 1 to 50 is user-defined CPUInterfaceFilter, and the ID more than 50 is reserved for system-defined CPUInterfaceFilter. The user only allow to create user-defined CPUInterfaceFilter ID. And system-defined CPUInterfaceFilter is read only.
OBJECT-TYPE    
  Integer32 1..3  

cpuFilterProfileType 1.3.6.1.4.1.171.10.75.14.33.1.1.1.2
The CPUInterfaceFilter Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule,
OBJECT-TYPE    
  INTEGER l2(1), l3(2)  

cpuFilterProfileRuleCount 1.3.6.1.4.1.171.10.75.14.33.1.1.1.3
The number of rules in this profile.
OBJECT-TYPE    
  Integer32 0..65535  

cpuFilterProfileMask 1.3.6.1.4.1.171.10.75.14.33.1.1.1.4
Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST-MAC 0 (LSB) L2 SRC-MAC 1 L2 VID 2 L2 8021P-PRIORITY 3 L2 ETHER-TYPE 4 L3 DSCP 5 L3 ICMP-TYPE 6 L3 ICMP-CODE 7 L3 IGMP-TYPE 8 L3 DST-IP 9 L3 SRC-IP 10 L3 DST-PORT 11 L3 SRC-PORT 12 L3 TCPFLAG 13 (MSB) ------------------------------------------- The value is in Hex format.
OBJECT-TYPE    
  OCTET STRING  

cpuFilterProfileDstMacAddrMask 1.3.6.1.4.1.171.10.75.14.33.1.1.1.5
The CPUInterfaceFilter Profile destination MAC address mask. If DST-MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleDstMacAddr, to caculate a range of MAC address which is really care.
OBJECT-TYPE    
  MacAddress  

cpuFilterProfileSrcMacAddrMask 1.3.6.1.4.1.171.10.75.14.33.1.1.1.6
The CPUInterfaceFilter Profile source MAC address mask. If SRC-MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.
OBJECT-TYPE    
  MacAddress  

cpuFilterProfileIPProtocol 1.3.6.1.4.1.171.10.75.14.33.1.1.1.7
Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none.
OBJECT-TYPE    
  INTEGER none(0), icmp(1), igmp(2), tcp(6), udp(17), ipMask(255)  

cpuFilterProfileIPProtocolMask 1.3.6.1.4.1.171.10.75.14.33.1.1.1.8
The CPUInterfaceFilter Profile IP protocol mask. If cpuFilterProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,cpuFilterL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.
OBJECT-TYPE    
  OCTET STRING  

cpuFilterProfileDstIpAddrMask 1.3.6.1.4.1.171.10.75.14.33.1.1.1.9
The CPUInterfaceFilter Profile destination IP address mask. If DST-IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
OBJECT-TYPE    
  IpAddress  

cpuFilterProfileSrcIpAddrMask 1.3.6.1.4.1.171.10.75.14.33.1.1.1.10
The CPUInterfaceFilter Profile source IP address mask. If SRC-IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
OBJECT-TYPE    
  IpAddress  

cpuFilterProfileDstPortMask 1.3.6.1.4.1.171.10.75.14.33.1.1.1.11
The CPUInterfaceFilter Profile UDP/TCP destination port mask. If DST-PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format.
OBJECT-TYPE    
  OCTET STRING  

cpuFilterProfileSrcPortMask 1.3.6.1.4.1.171.10.75.14.33.1.1.1.12
The CPUInterfaceFilter Profile UDP/TCP source port mask. If SRC-PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format.
OBJECT-TYPE    
  OCTET STRING  

cpuFilterProfileStatus 1.3.6.1.4.1.171.10.75.14.33.1.1.1.15
This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of cpuFilterProfileType, cpuFilterProfileMask and ProtocolType are not conflicted.
OBJECT-TYPE    
  RowStatus  

cpuFilterL2Rule 1.3.6.1.4.1.171.10.75.14.33.2
OBJECT IDENTIFIER    

cpuFilterL2RuleTable 1.3.6.1.4.1.171.10.75.14.33.2.1
A table to configure L2 filter rules in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    CpuFilterL2RuleEntry

cpuFilterL2RuleEntry 1.3.6.1.4.1.171.10.75.14.33.2.1.1
Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID.
OBJECT-TYPE    
  CpuFilterL2RuleEntry  

cpuFilterL2ProfileID 1.3.6.1.4.1.171.10.75.14.33.2.1.1.1
L2 Filter rule ID.
OBJECT-TYPE    
  Integer32 1..3  

cpuFilterL2AccessID 1.3.6.1.4.1.171.10.75.14.33.2.1.1.2
CPUInterfaceFilter Profile ID which this rule join.
OBJECT-TYPE    
  Integer32 1..5  

cpuFilterL2RuleEtherType 1.3.6.1.4.1.171.10.75.14.33.2.1.1.3
The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1 | 1501..65535  

cpuFilterL2RuleDstMacAddr 1.3.6.1.4.1.171.10.75.14.33.2.1.1.4
Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition.
OBJECT-TYPE    
  MacAddress  

cpuFilterL2RuleSrcMacAddr 1.3.6.1.4.1.171.10.75.14.33.2.1.1.5
Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address
OBJECT-TYPE    
  MacAddress  

cpuFilterL2RuleVlanId 1.3.6.1.4.1.171.10.75.14.33.2.1.1.6
Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1..4094  

cpuFilterL2Rule1pPriority 1.3.6.1.4.1.171.10.75.14.33.2.1.1.7
802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1..7  

cpuFilterL2RuleDstMacAddrMask 1.3.6.1.4.1.171.10.75.14.33.2.1.1.8
The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting.
OBJECT-TYPE    
  MacAddress  

cpuFilterL2RuleSrcMacAddrMask 1.3.6.1.4.1.171.10.75.14.33.2.1.1.9
The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting.
OBJECT-TYPE    
  MacAddress  

cpuFilterL2RuleInPortList 1.3.6.1.4.1.171.10.75.14.33.2.1.1.10
Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list.
OBJECT-TYPE    
  PortList  

cpuFilterL2RuleAction 1.3.6.1.4.1.171.10.75.14.33.2.1.1.11
Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded.
OBJECT-TYPE    
  INTEGER allow(1), drop(2)  

cpuFilterL2RuleStatus 1.3.6.1.4.1.171.10.75.14.33.2.1.1.14
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
OBJECT-TYPE    
  RowStatus  

cpuFilterL3Rule 1.3.6.1.4.1.171.10.75.14.33.3
OBJECT IDENTIFIER    

cpuFilterL3RuleTable 1.3.6.1.4.1.171.10.75.14.33.3.1
A table to configure L3 filter rules in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    CpuFilterL3RuleEntry

cpuFilterL3RuleEntry 1.3.6.1.4.1.171.10.75.14.33.3.1.1
Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID.
OBJECT-TYPE    
  CpuFilterL3RuleEntry  

cpuFilterL3RuleProfileNo 1.3.6.1.4.1.171.10.75.14.33.3.1.1.1
L3 Filter rule ID.
OBJECT-TYPE    
  Integer32 1..5  

cpuFilterL3RuleAccessID 1.3.6.1.4.1.171.10.75.14.33.3.1.1.2
The Profile ID which this rule join.
OBJECT-TYPE    
  Integer32 1..3  

cpuFilterL3RuleProtocol 1.3.6.1.4.1.171.10.75.14.33.3.1.1.3
The type of protocol to be checked against the packet.
OBJECT-TYPE    
  INTEGER icmp(1), igmp(2), tcp(6), udp(17)  

cpuFilterL3RuleProtocolMask 1.3.6.1.4.1.171.10.75.14.33.3.1.1.4
The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,cpuFilterL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.
OBJECT-TYPE    
  OCTET STRING  

cpuFilterL3RuleICMPMessageType 1.3.6.1.4.1.171.10.75.14.33.3.1.1.5
The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in cpuFilterL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18),
OBJECT-TYPE    
  Integer32 -1..255  

cpuFilterL3RuleICMPMessageCode 1.3.6.1.4.1.171.10.75.14.33.3.1.1.6
The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in cpuFilterL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12),
OBJECT-TYPE    
  Integer32 -1..255  

cpuFilterL3RuleDstIpAddr 1.3.6.1.4.1.171.10.75.14.33.3.1.1.7
Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
OBJECT-TYPE    
  IpAddress  

cpuFilterL3RuleSrcIpAddr 1.3.6.1.4.1.171.10.75.14.33.3.1.1.8
Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
OBJECT-TYPE    
  IpAddress  

cpuFilterL3RuleDstIpAddrMask 1.3.6.1.4.1.171.10.75.14.33.3.1.1.9
The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting.
OBJECT-TYPE    
  IpAddress  

cpuFilterL3RuleSrcIpAddrMask 1.3.6.1.4.1.171.10.75.14.33.3.1.1.10
The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting.
OBJECT-TYPE    
  IpAddress  

cpuFilterL3RuleTcpUdpDstPort 1.3.6.1.4.1.171.10.75.14.33.3.1.1.11
The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1..65535  

cpuFilterL3RuleTcpUdpSrcPort 1.3.6.1.4.1.171.10.75.14.33.3.1.1.12
The TCP / UDP source port. The default value is -1, which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1..65535  

cpuFilterL3RuleTcpUdpDstPortMask 1.3.6.1.4.1.171.10.75.14.33.3.1.1.13
The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting.
OBJECT-TYPE    
  OCTET STRING  

cpuFilterL3RuleTcpUdpSrcPortMask 1.3.6.1.4.1.171.10.75.14.33.3.1.1.14
The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting.
OBJECT-TYPE    
  OCTET STRING  

cpuFilterL3RuleTcpAckBit 1.3.6.1.4.1.171.10.75.14.33.3.1.1.15
The TCP ACK bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
OBJECT-TYPE    
  INTEGER dontcare(-1), establish(1), notEstablish(2)  

cpuFilterL3RuleTcpRstBit 1.3.6.1.4.1.171.10.75.14.33.3.1.1.16
The TCP RST bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
OBJECT-TYPE    
  INTEGER dontcare(-1), establish(1), notEstablish(2)  

cpuFilterL3RuleTcpUrgBit 1.3.6.1.4.1.171.10.75.14.33.3.1.1.17
The TCP Urg bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
OBJECT-TYPE    
  INTEGER dontcare(-1), establish(1), notEstablish(2)  

cpuFilterL3RuleTcpPshBit 1.3.6.1.4.1.171.10.75.14.33.3.1.1.18
The TCP Psh bit to be checked against the packet. The default value is 'dontcare'(-1). which means the rule don't care this condition.
OBJECT-TYPE    
  INTEGER dontcare(-1), establish(1), notEstablish(2)  

cpuFilterL3RuleTcpSynBit 1.3.6.1.4.1.171.10.75.14.33.3.1.1.19
The TCP Syn bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
OBJECT-TYPE    
  INTEGER dontcare(-1), establish(1), notEstablish(2)  

cpuFilterL3RuleTcpFinBit 1.3.6.1.4.1.171.10.75.14.33.3.1.1.20
The TCP Fin bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
OBJECT-TYPE    
  INTEGER dontcare(-1), establish(1), notEstablish(2)  

cpuFilterL3RuleDscp 1.3.6.1.4.1.171.10.75.14.33.3.1.1.21
The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1..63  

cpuFilterL3RuleIgmpType 1.3.6.1.4.1.171.10.75.14.33.3.1.1.22
The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition.
OBJECT-TYPE    
  Integer32 -1..255  

cpuFilterL3RulePortList 1.3.6.1.4.1.171.10.75.14.33.3.1.1.23
Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable.
OBJECT-TYPE    
  PortList  

cpuFilterL3RuleAction 1.3.6.1.4.1.171.10.75.14.33.3.1.1.24
Specifies the action to be taken on the packet if the filter rule matches.
OBJECT-TYPE    
  INTEGER allow(1), drop(2)  

cpuFilterL3RuleStatus 1.3.6.1.4.1.171.10.75.14.33.3.1.1.27
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
OBJECT-TYPE    
  RowStatus  

snmpGlobalState 1.3.6.1.4.1.171.10.75.14.5.1
This object is for enabling or disabling SNMP Community function.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

snmpV3User 1.3.6.1.4.1.171.10.75.14.5.2
OBJECT IDENTIFIER    

snmpV3Group 1.3.6.1.4.1.171.10.75.14.5.3
OBJECT IDENTIFIER    

snmpV3ViewTree 1.3.6.1.4.1.171.10.75.14.5.4
OBJECT ID