DASAN-BRIDGE-MIB

File: DASAN-BRIDGE-MIB.mib (26856 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI SNMPv2-TC
SNMPv2-CONF IF-MIB DASAN-SMI
DASAN-SWITCH-MIB

Imported symbols

Counter MODULE-IDENTITY OBJECT-TYPE
Counter32 Gauge32 Counter64
Unsigned32 Integer32 TimeTicks
mib-2 NOTIFICATION-TYPE TEXTUAL-CONVENTION
DisplayString PhysAddress TruthValue
RowStatus TimeStamp AutonomousType
TestAndIncr MODULE-COMPLIANCE OBJECT-GROUP
ifIndex dasanEvents dasanMgmt
dasanModules dasanSwitchMIBObjects dsSwitchModules

Defined Types

MacAddress  
OCTET STRING Size(6)    

BridgeId  
OCTET STRING Size(8)    

Timeout  
INTEGER    

PortList  
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
TEXTUAL-CONVENTION    
  OCTET STRING  

VlanIndex  
A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention). If the value is greater than 4095 then it represents a VLAN with scope local to the particular agent, i.e. one without a global VLAN-ID assigned to it. Such VLANs are outside the scope of IEEE 802.1Q but it is convenient to be able to manage them in the same way using this MIB.
TEXTUAL-CONVENTION    
  Unsigned32  

VlanId  
A 12-bit VLAN ID used in the VLAN Tag header.
TEXTUAL-CONVENTION    
  INTEGER 1..4094  

DsVlanCurrentEntry  
SEQUENCE    
  dsVlanIndex VlanIndex
  dsVlanName OCTET STRING
  dsVlanFdbId Unsigned32
  dsVlanCurrentEgressPorts PortList
  dsVlanCurrentUntaggedPorts PortList
  dsVlanStatus INTEGER
  dsVlanCreationTime TimeTicks
  dsVlanCurrentPhysicalPorts PortList

DsTpFdbEntry  
SEQUENCE    
  dsTpFdbFid INTEGER
  dsTpFdbVlanName OCTET STRING
  dsTpFdbAddress MacAddress
  dsTpFdbPort Integer32
  dsTpFdbStatus INTEGER

DsStpEntry  
SEQUENCE    
  dsStpIndex INTEGER
  dsStpVid INTEGER
  dsStpProtocolSpecification INTEGER
  dsStpPriority Integer32
  dsStpTimeSinceTopologyChange TimeTicks
  dsStpTopChanges Counter
  dsStpDesignatedRoot BridgeId
  dsStpRootCost INTEGER
  dsStpRootPort INTEGER
  dsStpMaxAge Timeout
  dsStpHelloTime Timeout
  dsStpHoldTime INTEGER
  dsStpForwardDelay Timeout
  dsStpBridgeMaxAge Timeout
  dsStpBridgeHelloTime Timeout
  dsStpBridgeForwardDelay Timeout

DsStpPortEntry  
SEQUENCE    
  dsStpPort Integer32
  dsStpPortPriority Integer32
  dsStpPortState INTEGER
  dsStpPortEnable INTEGER
  dsStpPortPathCost Integer32
  dsStpPortDesignatedRoot BridgeId
  dsStpPortDesignatedCost INTEGER
  dsStpPortDesignatedBridge BridgeId
  dsStpPortDesignatedPort OCTET STRING
  dsStpPortForwardTransitions Counter

Defined Values

dsBridge 1.3.6.1.4.1.6296.9.1.1.2.22
The MIB module to describe bridge of DASAN product.
MODULE-IDENTITY    

dsTp 1.3.6.1.4.1.6296.9.1.1.2.22.3
OBJECT IDENTIFIER    

dsVlanBase 1.3.6.1.4.1.6296.9.1.1.2.22.1
OBJECT IDENTIFIER    

dsVlanVersionNumber 1.3.6.1.4.1.6296.9.1.1.2.22.1.1
The version number of IEEE 802.1Q that this device supports.
OBJECT-TYPE    
  INTEGER version1(1)  

dsVlanMaxVlanId 1.3.6.1.4.1.6296.9.1.1.2.22.1.2
The maximum IEEE 802.1Q VLAN ID that this device supports.
OBJECT-TYPE    
  VlanId  

dsVlanMaxSupportedVlans 1.3.6.1.4.1.6296.9.1.1.2.22.1.3
The maximum number of VLANs that this device supports.
OBJECT-TYPE    
  Unsigned32  

dsVlanNumVlans 1.3.6.1.4.1.6296.9.1.1.2.22.1.4
The current number of VLANs that are configured in this device.
OBJECT-TYPE    
  Unsigned32  

dsVlanGvrpStatus 1.3.6.1.4.1.6296.9.1.1.2.22.1.5
The administrative status requested by management for GVRP. The value enabled(1) indicates that GVRP should be enabled on this device, on all ports for which it has not been specifically disabled. When disabled(2), GVRP is disabled on all ports and all GVRP packets will be forwarded transparently. This object affects all GVRP Applicant and Registrar state machines. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on all ports.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dsVlanCurrentTable 1.3.6.1.4.1.6296.9.1.1.2.22.2
A table containing current configuration information for each VLAN currently configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received.
OBJECT-TYPE    
  SEQUENCE OF  
    DsVlanCurrentEntry

dsVlanCurrentEntry 1.3.6.1.4.1.6296.9.1.1.2.22.2.1
Information for a VLAN configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received.
OBJECT-TYPE    
  DsVlanCurrentEntry  

dsVlanIndex 1.3.6.1.4.1.6296.9.1.1.2.22.2.1.1
The VLAN-ID or other identifier refering to this VLAN.
OBJECT-TYPE    
  VlanIndex  

dsVlanName 1.3.6.1.4.1.6296.9.1.1.2.22.2.1.2
The VLAN-NAME to this VLAN.
OBJECT-TYPE    
  OCTET STRING  

dsVlanFdbId 1.3.6.1.4.1.6296.9.1.1.2.22.2.1.3
The Filtering Database used by this VLAN. This value is allocated automatically by the device whenever the VLAN is created: either dynamically by GVRP, or by management, in dot1qVlanStaticTable. Allocation of this value follows the learning constraints defined for this VLAN in dot1qLearningConstraintsTable.
OBJECT-TYPE    
  Unsigned32  

dsVlanCurrentEgressPorts 1.3.6.1.4.1.6296.9.1.1.2.22.2.1.4
The set of ports which are transmitting traffic for this VLAN as either tagged or untagged frames.
OBJECT-TYPE    
  PortList  

dsVlanCurrentUntaggedPorts 1.3.6.1.4.1.6296.9.1.1.2.22.2.1.5
The set of ports which are transmitting traffic for this VLAN as untagged frames.
OBJECT-TYPE    
  PortList  

dsVlanStatus 1.3.6.1.4.1.6296.9.1.1.2.22.2.1.6
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the following values. permanent(2) - this entry, corresponding to an entry in dot1qVlanStaticTable, is currently in use and will remain so after the next reset of the device. The port lists for this entry include ports from the equivalent dot1qVlanStaticTable entry and ports learnt dynamically. dynamicGvrp(3) - this entry is currently in use and will remain so until removed by GVRP. There is no static entry for this VLAN and it will be removed when the last port leaves the VLAN.
OBJECT-TYPE    
  INTEGER other(1), permanent(2), dynamicGvrp(3)  

dsVlanCreationTime 1.3.6.1.4.1.6296.9.1.1.2.22.2.1.7
The value of sysUpTime when this VLAN was created.
OBJECT-TYPE    
  TimeTicks  

dsVlanCurrentPhysicalPorts 1.3.6.1.4.1.6296.9.1.1.2.22.2.1.8
The set of ports which are physical.
OBJECT-TYPE    
  PortList  

dsTpFdbTable 1.3.6.1.4.1.6296.9.1.1.2.22.3.1
A table that contains information about unicast entries for which the device has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
OBJECT-TYPE    
  SEQUENCE OF  
    DsTpFdbEntry

dsTpFdbEntry 1.3.6.1.4.1.6296.9.1.1.2.22.3.1.1
Information about a specific unicast MAC address for which the device has some forwarding and/or filtering information.
OBJECT-TYPE    
  DsTpFdbEntry  

dsTpFdbFid 1.3.6.1.4.1.6296.9.1.1.2.22.3.1.1.1
The identity of this Filtering Database.
OBJECT-TYPE    
  INTEGER  

dsTpFdbVlanName 1.3.6.1.4.1.6296.9.1.1.2.22.3.1.1.2
The name of VLAN related to this Filtering Database.
OBJECT-TYPE    
  OCTET STRING  

dsTpFdbAddress 1.3.6.1.4.1.6296.9.1.1.2.22.3.1.1.3
A unicast MAC address for which the bridge has forwarding and/or filtering information.
OBJECT-TYPE    
  OCTET STRING Size(6)  

dsTpFdbPort 1.3.6.1.4.1.6296.9.1.1.2.22.3.1.1.4
Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of dsTpFdbAddress has been seen.
OBJECT-TYPE    
  Integer32 0..65535  

dsTpFdbStatus 1.3.6.1.4.1.6296.9.1.1.2.22.3.1.1.5
The status of this entry. The meanings of the values are: other(1) - none of the following. invalid(2) - this entry is no longer valid (e.g., it was learned but has since aged out), but has not yet been flushed from the table. learned(3) - the value of the corresponding instance of dsTpFdbPort was learned and is being used. self(4) - the value of the corresponding instance of dsTpFdbAddress represents one of the device's addresses. The corresponding instance of dsTpFdbPort indicates which of the device's ports has this address. mgmt(5) - the value of the corresponding instance of dsTpFdbAddress is also the value of an existing instance of dsStaticAddress.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), learned(3), self(4), mgmt(5)  

dsStpBase 1.3.6.1.4.1.6296.9.1.1.2.22.4
OBJECT IDENTIFIER    

dsStpTable 1.3.6.1.4.1.6296.9.1.1.2.22.5
The table of STP supported this device.
OBJECT-TYPE    
  SEQUENCE OF  
    DsStpEntry

dsStpEntry 1.3.6.1.4.1.6296.9.1.1.2.22.5.1
The table of STP supported this device.
OBJECT-TYPE    
  DsStpEntry  

dsStpIndex 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.1
.
OBJECT-TYPE    
  INTEGER  

dsStpVid 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.2
.
OBJECT-TYPE    
  INTEGER  

dsStpProtocolSpecification 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.3
An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
OBJECT-TYPE    
  INTEGER unknown(1), decLb100(2), ieee8021d(3)  

dsStpPriority 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.4
The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of dot1dBaseBridgeAddress.
OBJECT-TYPE    
  Integer32 0..65535  

dsStpTimeSinceTopologyChange 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.5
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
OBJECT-TYPE    
  TimeTicks  

dsStpTopChanges 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.6
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
OBJECT-TYPE    
  Counter  

dsStpDesignatedRoot 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.7
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
OBJECT-TYPE    
  BridgeId  

dsStpRootCost 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.8
The cost of the path to the root as seen from this bridge.
OBJECT-TYPE    
  INTEGER  

dsStpRootPort 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.9
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
OBJECT-TYPE    
  INTEGER  

dsStpMaxAge 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.10
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
OBJECT-TYPE    
  Timeout  

dsStpHelloTime 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.11
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
OBJECT-TYPE    
  Timeout  

dsStpHoldTime 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.12
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
OBJECT-TYPE    
  INTEGER  

dsStpForwardDelay 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.13
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
OBJECT-TYPE    
  Timeout  

dsStpBridgeMaxAge 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.14
The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
OBJECT-TYPE    
  Timeout 600..4000  

dsStpBridgeHelloTime 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.15
The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
OBJECT-TYPE    
  Timeout 100..1000  

dsStpBridgeForwardDelay 1.3.6.1.4.1.6296.9.1.1.2.22.5.1.16
The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
OBJECT-TYPE    
  Timeout 400..3000  

dsStpPortTable 1.3.6.1.4.1.6296.9.1.1.2.22.6
The port table of STP supported this device.
OBJECT-TYPE    
  SEQUENCE OF  
    DsStpPortEntry

dsStpPortEntry 1.3.6.1.4.1.6296.9.1.1.2.22.6.1
The port table of STP supported this device.
OBJECT-TYPE    
  DsStpPortEntry  

dsStpPort 1.3.6.1.4.1.6296.9.1.1.2.22.6.1.1
The port number of the port for which this entry contains Spanning Tree Protocol management information.
OBJECT-TYPE    
  Integer32 1..65535  

dsStpPortPriority 1.3.6.1.4.1.6296.9.1.1.2.22.6.1.2
The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of dot1dStpPort.
OBJECT-TYPE    
  Integer32 0..255  

dsStpPortState 1.3.6.1.4.1.6296.9.1.1.2.22.6.1.3
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dsStpPortEnable), this object will have a value of disabled(1).
OBJECT-TYPE    
  INTEGER disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)  

dsStpPortEnable 1.3.6.1.4.1.6296.9.1.1.2.22.6.1.4
The enabled/disabled status of the port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dsStpPortPathCost 1.3.6.1.4.1.6296.9.1.1.2.22.6.1.5
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
OBJECT-TYPE    
  Integer32 1..65535  

dsStpPortDesignatedRoot 1.3.6.1.4.1.6296.9.1.1.2.22.6.1.6
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
OBJECT-TYPE    
  BridgeId  

dsStpPortDesignatedCost 1.3.6.1.4.1.6296.9.1.1.2.22.6.1.7
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OBJECT-TYPE    
  INTEGER  

dsStpPortDesignatedBridge 1.3.6.1.4.1.6296.9.1.1.2.22.6.1.8
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
OBJECT-TYPE    
  BridgeId  

dsStpPortDesignatedPort 1.3.6.1.4.1.6296.9.1.1.2.22.6.1.9
The Port Identifier of the port on the Designated Bridge for this port's segment.
OBJECT-TYPE    
  OCTET STRING Size(2)  

dsStpPortForwardTransitions 1.3.6.1.4.1.6296.9.1.1.2.22.6.1.10
The number of times this port has transitioned from the Learning state to the Forwarding state.
OBJECT-TYPE    
  Counter