CXT1E1-MIB

File: CXT1E1-MIB.mib (5423 bytes)

Imported modules

RFC-1212 RFC1155-SMI CXProduct-SMI

Imported symbols

OBJECT-TYPE TimeTicks cxT1E1

Defined Types

T1e1CfgEntry  
SEQUENCE    
  t1e1CfgLinkIndex INTEGER
  t1e1CfgDebounce INTEGER
  t1e1CfgJitterAttenuator INTEGER
  t1e1CfgSyncCriteria INTEGER
  t1e1CfgT1RxEqualizerGainLimit INTEGER
  t1e1CfgT1RxLevel INTEGER
  t1e1CfgT1FrameAlignmentChange TimeTicks
  t1e1CfgT1JitterAttenuatorTrip TimeTicks

Defined Values

t1e1CfgTable 1.3.6.1.4.1.495.2.1.8.2.10
The T1/E1 configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    T1e1CfgEntry

t1e1CfgEntry 1.3.6.1.4.1.495.2.1.8.2.10.1
An entry in the T1/E1 configuration table.
OBJECT-TYPE    
  T1e1CfgEntry  

t1e1CfgLinkIndex 1.3.6.1.4.1.495.2.1.8.2.10.1.1
Identifies the physical port with the T1/E1 (t1e1) interface. Range of Values: 1 - 2 Default Value: None Configuration Changed: administrative
OBJECT-TYPE    
  INTEGER 1..2  

t1e1CfgDebounce 1.3.6.1.4.1.495.2.1.8.2.10.1.10
Specifies the number of loops needed for debouncing. Warning: This is a Private Mode activity that should only be performed by or under the direct supervision of qualified personnel. Range of Values: 1 - 255 Default Value: 2 Configuration Changed: administrative
OBJECT-TYPE    
  INTEGER 1..255  

t1e1CfgJitterAttenuator 1.3.6.1.4.1.495.2.1.8.2.10.1.11
Defines the position and buffer depth of the Jitter Attenuator when the Attenuator is enabled. Warning: This is a Private Mode activity that should only be performed by or under the direct supervision of qualified personnel. Options: t1e1NoJitterAttenuator (1) t1e1RxAttenuator32Bits (2) t1e1RxAttenuator128Bits (3) t1e1TxAttenuator32Bits (4) t1e1TxAttenuator128Bits (5) Default Value: t1e1NoJitterAttenuator (1) Configuration Changed: administrative
OBJECT-TYPE    
  INTEGER t1e1NoJitterAttenuator(1), t1e1RxAttenuator32Bits(2), t1e1RxAttenuator128Bits(3), t1e1TxAttenuator32Bits(4), t1e1TxAttenuator128Bits(5)  

t1e1CfgSyncCriteria 1.3.6.1.4.1.495.2.1.8.2.10.1.12
Determines the criteria used for Synchronisation. Options: In D4 framing mode, 1 = search for Ft pattern, the search for Fs pattern and 2=cross couple Ft and Fs pattern. In ESF framing mode, 1 = search for FPS pattern only. In ESF framing mode, 2 = search for FPS and verify with CRC6. Warning: This is a Private Mode activity that should only be performed by or under the direct supervision of qualified personnel. Default Value: 1 Configuration Changed: administrative
OBJECT-TYPE    
  INTEGER 1..2  

t1e1CfgT1RxEqualizerGainLimit 1.3.6.1.4.1.495.2.1.8.2.10.1.13
Program the receiver sensitivity. Warning: This is a Private Mode activity that should only be performed by or under the direct supervision of qualified personnel. Options: t1e1EGLLow (1): Program a low sensitivity of -30 dB. This is recommended for most applications. t1e1EGLHigh (2): Program a high sensitivity of -36 dB. This setting could be required for particular applications, however, with this level of sensitivity the receiver will be more susceptible to crosstalk and the receiver's jitter tolerance will suffer. Default Value: t1e1EGLLow (1) Configuration Changed: administrative
OBJECT-TYPE    
  INTEGER t1e1EGLLow(1), t1e1EGLHigh(2)  

t1e1CfgT1RxLevel 1.3.6.1.4.1.495.2.1.8.2.10.1.50
Indicates in real-time a range of received signal levels. Options: 1: +2.0 to -7.5 dB 2: -7.5 to -15.0 dB 3: -15.0 to -22.5 dB 4: less than -22.5 dB
OBJECT-TYPE    
  INTEGER 1..4  

t1e1CfgT1FrameAlignmentChange 1.3.6.1.4.1.495.2.1.8.2.10.1.51
Indicates the most recent time at which a resynchronization resulted in a change of frame or multiframe alignment. If no such event has occurred since system startup, then the value will be zero.
OBJECT-TYPE    
  TimeTicks  

t1e1CfgT1JitterAttenuatorTrip 1.3.6.1.4.1.495.2.1.8.2.10.1.52
Indicates the most recent time that the jitter attenuator FIFO reached within 4-bits of it's limit on this line interface. If no such event has occurred since system startup, then the value will be zero.
OBJECT-TYPE    
  TimeTicks