CXMCPRT-MIB

Imported modules

RFC1155-SMI	RFC1213-MIB	RFC-1212
CXProduct-SMI

Imported symbols

Counter	TimeTicks	DisplayString
OBJECT-TYPE	cxMc600

Defined Types

CxMcPrtCfgEntry
SEQUENCE
	cxMcPrtCfgPortIndex	INTEGER
	cxMcPrtCfgDriverUsed	INTEGER
	cxMcPrtCfgReinitPort	INTEGER
	cxMcPrtCfgUpdated	INTEGER

CxMcPrtStatEntry
SEQUENCE
	cxMcPrtStatPortNumber	INTEGER
	cxMcPrtStatRts	INTEGER
	cxMcPrtStatDtr	INTEGER
	cxMcPrtStatDsr	INTEGER
	cxMcPrtStatDcd	INTEGER
	cxMcPrtStatCts	INTEGER
	cxMcPrtStatCntMsgTx	Counter
	cxMcPrtStatCntMsgRx	Counter
	cxMcPrtStatCntReinit	Counter
	cxMcPrtStatCntFlowCtrlTx	Counter
	cxMcPrtStatCntFlowCtrlRx	Counter
	cxMcPrtStatCntErrTx	Counter
	cxMcPrtStatCntErrRx	Counter
	cxMcPrtStatCntConnect	Counter
	cxMcPrtStatCntChrDecomp	Counter
	cxMcPrtStatCntChrComp	Counter
	cxMcPrtStatCntBitDecomp	Counter
	cxMcPrtStatCntBitComp	Counter
	cxMcPrtStatStation	INTEGER
	cxMcPrtStatRoute	INTEGER
	cxMcPrtStatHwInterface	INTEGER
	cxMcPrtStatTimeTicks	TimeTicks

CxMcPrtBopEntry
SEQUENCE
	cxMcPrtBopPortUsed	INTEGER
	cxMcPrtBopPortStatus	INTEGER
	cxMcPrtBopComRate	INTEGER
	cxMcPrtBopUseLnkErrPassthro	INTEGER
	cxMcPrtBopInterface	INTEGER
	cxMcPrtBopRtsDcdModemCtrl	INTEGER
	cxMcPrtBopUseRtsDcdCndDataTx	INTEGER
	cxMcPrtBopUseRtsDcdCndLnk	INTEGER
	cxMcPrtBopUseRtsDcdCndRem	INTEGER
	cxMcPrtBopDtrCtsModemCtrl	INTEGER
	cxMcPrtBopUseDtrCtsCndRts	INTEGER
	cxMcPrtBopUseDtrCtsCndLnk	INTEGER
	cxMcPrtBopUseDtrCtsCndRem	INTEGER
	cxMcPrtBopLimitBeforeOut	INTEGER
	cxMcPrtBopUseOutCndCtsDtrOn	INTEGER
	cxMcPrtBopUseInCndDcdRtsOn	INTEGER
	cxMcPrtBopSyncMode	INTEGER
	cxMcPrtBopDataLifetime	INTEGER
	cxMcPrtBopUseClockSync	INTEGER
	cxMcPrtBopUseFlowCtrlClock	INTEGER
	cxMcPrtBopFlowCtrlRate	INTEGER
	cxMcPrtBopLimitOutFlowCtrl	INTEGER
	cxMcPrtBopLimitInFlowCtrl	INTEGER
	cxMcPrtBopCoding	INTEGER
	cxMcPrtBopOutIdleState	INTEGER
	cxMcPrtBopDelayBeforeIdle	INTEGER
	cxMcPrtBopOutPreambleLng	INTEGER

CxMcPrtAsyEntry
SEQUENCE
	cxMcPrtAsyPortUsed	INTEGER
	cxMcPrtAsyPortStatus	INTEGER
	cxMcPrtAsyComRate	INTEGER
	cxMcPrtAsyUseLnkErrPassthro	INTEGER
	cxMcPrtAsyInterface	INTEGER
	cxMcPrtAsyRtsDcdModemCtrl	INTEGER
	cxMcPrtAsyUseRtsDcdCndDataTx	INTEGER
	cxMcPrtAsyUseRtsDcdCndLnk	INTEGER
	cxMcPrtAsyUseRtsDcdCndRem	INTEGER
	cxMcPrtAsyDtrCtsModemCtrl	INTEGER
	cxMcPrtAsyUseDtrCtsCndRts	INTEGER
	cxMcPrtAsyUseDtrCtsCndLnk	INTEGER
	cxMcPrtAsyUseDtrCtsCndRem	INTEGER
	cxMcPrtAsyLimitBeforeOut	INTEGER
	cxMcPrtAsyOutCndCtsDtrOn	INTEGER
	cxMcPrtAsyInCndDcdRtsOn	INTEGER
	cxMcPrtAsySyncMode	INTEGER
	cxMcPrtAsyUseDataLifeLimited	INTEGER
	cxMcPrtAsyDataLifetime	INTEGER
	cxMcPrtAsyOutFlowCtrl	INTEGER
	cxMcPrtAsyInFlowCtrl	INTEGER
	cxMcPrtAsyXonChr	INTEGER
	cxMcPrtAsyXoffChr	INTEGER
	cxMcPrtAsyNbBitPerChr	INTEGER
	cxMcPrtAsyParity	INTEGER
	cxMcPrtAsyNbStopBit	INTEGER
	cxMcPrtAsyUseFlushOutChr	INTEGER
	cxMcPrtAsyFlushOutChr	INTEGER

CxMcPrtCopEntry
SEQUENCE
	cxMcPrtCopPortUsed	INTEGER
	cxMcPrtCopPortStatus	INTEGER
	cxMcPrtCopComRate	INTEGER
	cxMcPrtCopUseLnkErrPassthro	INTEGER
	cxMcPrtCopInterfaceType	INTEGER
	cxMcPrtCopRtsDcdModemCtrl	INTEGER
	cxMcPrtCopUseRtsDcdCndDataTx	INTEGER
	cxMcPrtCopUseRtsDcdCndLnk	INTEGER
	cxMcPrtCopUseRtsDcdCndRem	INTEGER
	cxMcPrtCopDtrCtsModemCtrl	INTEGER
	cxMcPrtCopUseDtrCtsCndRts	INTEGER
	cxMcPrtCopUseDtrCtsCndLnk	INTEGER
	cxMcPrtCopUseDtrCtsCndRem	INTEGER
	cxMcPrtCopLimitBeforeOut	INTEGER
	cxMcPrtCopUseOutCndCtsDtrOn	INTEGER
	cxMcPrtCopUseInCndDcdRtsOn	INTEGER
	cxMcPrtCopSyncMode	INTEGER
	cxMcPrtCopDataLifetime	INTEGER
	cxMcPrtCopUseClockSync	INTEGER
	cxMcPrtCopUseFlowCtrlClock	INTEGER
	cxMcPrtCopFlowCtrlRate	INTEGER
	cxMcPrtCopLimitOutFlowCtrl	INTEGER
	cxMcPrtCopLimitInFlowCtrl	INTEGER
	cxMcPrtCopOutIdleState	INTEGER
	cxMcPrtCopNbBitPerChr	INTEGER
	cxMcPrtCopParity	INTEGER
	cxMcPrtCopSyncChrOne	INTEGER
	cxMcPrtCopSyncChrTwo	INTEGER
	cxMcPrtCopNbSyncChr	INTEGER
	cxMcPrtCopUseDesyncChr	INTEGER
	cxMcPrtCopDesyncChr	INTEGER
	cxMcPrtCopNbDesyncChr	INTEGER
	cxMcPrtCopUseDesyncRtsFall	INTEGER
	cxMcPrtCopBitSense	INTEGER

CxMcPrtBsyEntry
SEQUENCE
	cxMcPrtBsyPortUsed	INTEGER
	cxMcPrtBsyPortStatus	INTEGER
	cxMcPrtBsyComRate	INTEGER
	cxMcPrtBsyUseLnkErrPassthro	INTEGER
	cxMcPrtBsyInterface	INTEGER
	cxMcPrtBsyRtsDcdModemCtrl	INTEGER
	cxMcPrtBsyUseRtsDcdCndDataTx	INTEGER
	cxMcPrtBsyUseRtsDcdCndLnk	INTEGER
	cxMcPrtBsyUseRtsDcdCndRem	INTEGER
	cxMcPrtBsyDtrCtsModemCtrl	INTEGER
	cxMcPrtBsyUseDtrCtsCndRts	INTEGER
	cxMcPrtBsyUseDtrCtsCndLnk	INTEGER
	cxMcPrtBsyUseDtrCtsCndRem	INTEGER
	cxMcPrtBsyLimitBeforeOut	INTEGER
	cxMcPrtBsyUseOutCndCtsDtrOn	INTEGER
	cxMcPrtBsyUseInCndDcdRtsOn	INTEGER
	cxMcPrtBsySyncMode	INTEGER
	cxMcPrtBsyDataLifetime	INTEGER
	cxMcPrtBsyChrSet	INTEGER
	cxMcPrtBsyParity	INTEGER
	cxMcPrtBsyBlkChkChr	INTEGER
	cxMcPrtBsyNbSyncChr	INTEGER
	cxMcPrtBsyMaxFrameSize	INTEGER

Defined Values

cxMcPrt		1.3.6.1.4.1.495.2.1.1.1
OBJECT IDENTIFIER

cxMcPrtGlobal		1.3.6.1.4.1.495.2.1.1.1.1
OBJECT IDENTIFIER

cxMcPrtGlobalConsoleRate		1.3.6.1.4.1.495.2.1.1.1.1.1
The front panel console rate for the HC600. Range of Values: 300-19 200 Default Value: 19 200
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	300..19200

cxMcPrtGlobalResetStat		1.3.6.1.4.1.495.2.1.1.1.1.2
Resets all statistics. Options: no(1) yes (2) Default Value: no (1)
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtGlobalStationId		1.3.6.1.4.1.495.2.1.1.1.1.3
The local station identification. No space allowed in write.
Status: optional	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..12)

cxMcPrtCfgTable		1.3.6.1.4.1.495.2.1.1.1.2
cx Port Station Configuration Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CxMcPrtCfgEntry

cxMcPrtCfgEntry		1.3.6.1.4.1.495.2.1.1.1.2.1
cx Port Station Configuration Entry gives the state of the configuration associated to a particular port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CxMcPrtCfgEntry

cxMcPrtCfgPortIndex		1.3.6.1.4.1.495.2.1.1.1.2.1.1
Identifies the port by a numerical value. Range of Values: 1-4
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

cxMcPrtCfgDriverUsed		1.3.6.1.4.1.495.2.1.1.1.2.1.2
Specifies the port driver used. The driver is associated with a numerical value that identify one of the tables below the object identifier; cxMcPrtDriver for MC600, or cxMcPrtDriver for HC600 driver. Note that HC600 has only one driver. Options: bop(1): MC600 or HC600 asy(2): MC600 only cop(3): MC600 only bsy(4): MC600 only
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

cxMcPrtCfgReinitPort		1.3.6.1.4.1.495.2.1.1.1.2.1.3
Activate the planned configurations of the indexed port. Options: no (1) yes (2)
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCfgUpdated		1.3.6.1.4.1.495.2.1.1.1.2.1.4
The status of the configuration of a port. Options: no (1) yes (2)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtStatTable		1.3.6.1.4.1.495.2.1.1.1.3
cx Port Station Statistic Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CxMcPrtStatEntry

cxMcPrtStatEntry		1.3.6.1.4.1.495.2.1.1.1.3.1
cx Port Station Statistic Entry gives the state of the counters associated with a particular port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CxMcPrtStatEntry

cxMcPrtStatPortNumber		1.3.6.1.4.1.495.2.1.1.1.3.1.1
Indicates the port number of the statistics. Range of Values: 1-4
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

cxMcPrtStatRts		1.3.6.1.4.1.495.2.1.1.1.3.1.2
Indicates the current state of the Request to Send signal. Options: off (1) on (2)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(1), on(2)

cxMcPrtStatDtr		1.3.6.1.4.1.495.2.1.1.1.3.1.3
Indicates the current state of the Data Terminal Ready signal. Options: off (1) on (2)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(1), on(2)

cxMcPrtStatDsr		1.3.6.1.4.1.495.2.1.1.1.3.1.4
Indicates the current state of the Data Set Ready signal. Options: off (1) on (2)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(1), on(2)

cxMcPrtStatDcd		1.3.6.1.4.1.495.2.1.1.1.3.1.5
Indicates the current state of the Data Carrier Detect signal. Options: off (1) on (2)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(1), on(2)

cxMcPrtStatCts		1.3.6.1.4.1.495.2.1.1.1.3.1.6
Indicates the current state of the Clear to Send signal. Options: off (1) on (2)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(1), on(2)

cxMcPrtStatCntMsgTx		1.3.6.1.4.1.495.2.1.1.1.3.1.7
Indicates the number of frames transmitted on the specified port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

cxMcPrtStatCntMsgRx		1.3.6.1.4.1.495.2.1.1.1.3.1.8
Indicates the number of frames received on the specified port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

cxMcPrtStatCntReinit		1.3.6.1.4.1.495.2.1.1.1.3.1.9
Indicates the number of times that the specified port has reinitialized.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

cxMcPrtStatCntFlowCtrlTx		1.3.6.1.4.1.495.2.1.1.1.3.1.10
Indicates the number of times that the specified port has performed output flow control.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

cxMcPrtStatCntFlowCtrlRx		1.3.6.1.4.1.495.2.1.1.1.3.1.11
Indicates the number of times that the specified port has performed input flow control.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

cxMcPrtStatCntErrTx		1.3.6.1.4.1.495.2.1.1.1.3.1.12
Indicates the number of bad frames transmitted on the specified port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

cxMcPrtStatCntErrRx		1.3.6.1.4.1.495.2.1.1.1.3.1.13
Indicates the number of bad frames received on the specified port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

cxMcPrtStatCntConnect		1.3.6.1.4.1.495.2.1.1.1.3.1.14
Indicates the number of connections for the specified port. The number of connections is equal to the number of times that the DTR modem signal changed from OFF to ON.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

cxMcPrtStatCntChrDecomp		1.3.6.1.4.1.495.2.1.1.1.3.1.15
Indicates the number of characters transmitted on the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

cxMcPrtStatCntChrComp		1.3.6.1.4.1.495.2.1.1.1.3.1.16
Indicates the number of characters received on the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

cxMcPrtStatCntBitDecomp		1.3.6.1.4.1.495.2.1.1.1.3.1.17
Indicates the number of bits transmitted on the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

cxMcPrtStatCntBitComp		1.3.6.1.4.1.495.2.1.1.1.3.1.18
Indicates the number of bits received on the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

cxMcPrtStatStation		1.3.6.1.4.1.495.2.1.1.1.3.1.19
Indicates the station that the port is using to transmit and receive data.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..16

cxMcPrtStatRoute		1.3.6.1.4.1.495.2.1.1.1.3.1.20
Indicates the route of the station that the port is using.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..64

cxMcPrtStatHwInterface		1.3.6.1.4.1.495.2.1.1.1.3.1.21
Indicates whether the hardware port interface is DCE or DTE. The value depends on the I/O hardware. Options: dce (1) dte (2)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	dce(1), dte(2)

cxMcPrtStatTimeTicks		1.3.6.1.4.1.495.2.1.1.1.3.1.22
Indicates the number of milliseconds since the last reset for the current station.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

cxMcPrtPath		1.3.6.1.4.1.495.2.1.1.1.4
OBJECT IDENTIFIER

cxMcPrtPathStationPri		1.3.6.1.4.1.495.2.1.1.1.4.1
The primary port station. Range of Values: 1-16 Default Value: 1
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..16

cxMcPrtPathRoutePri		1.3.6.1.4.1.495.2.1.1.1.4.2
The primary route. Range of Values: 1-64 Default Value: 1
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..64

cxMcPrtPathStationScd		1.3.6.1.4.1.495.2.1.1.1.4.3
The secondary port station. Range of Values: 1-16 Default Value: 2
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..16

cxMcPrtPathRouteScd		1.3.6.1.4.1.495.2.1.1.1.4.4
The secondary route. Range of Values: 1-64 Default Value: 2
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..64

cxMcPrtDriver		1.3.6.1.4.1.495.2.1.1.1.5
OBJECT IDENTIFIER

cxMcPrtBopTable		1.3.6.1.4.1.495.2.1.1.1.5.1
cx Port Station MC600 & HC600 Bop Driver Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CxMcPrtBopEntry

cxMcPrtBopEntry		1.3.6.1.4.1.495.2.1.1.1.5.1.1
cx Port Station MC600 & HC600 Bop Driver Entry gives the state of the variables associated to the Bit Oriented Protocol.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CxMcPrtBopEntry

cxMcPrtBopPortUsed		1.3.6.1.4.1.495.2.1.1.1.5.1.1.1
Indicates the current port number that is used by the BOP driver. Range of Values: 1-4
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

cxMcPrtBopPortStatus		1.3.6.1.4.1.495.2.1.1.1.5.1.1.2
Indicates whether the port is enabled or disabled. Options: disable (1) enable (2) Default Value: disable (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

cxMcPrtBopComRate		1.3.6.1.4.1.495.2.1.1.1.5.1.1.3
Indicates the port communication rates. Range of Values: HC600: 9600-2048000 MC600: 110-128000 Default Value: HC600: 56 000, MC600: 9600
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

cxMcPrtBopUseLnkErrPassthro		1.3.6.1.4.1.495.2.1.1.1.5.1.1.4
Indicates the link error passthrough state on the port. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBopInterface		1.3.6.1.4.1.495.2.1.1.1.5.1.1.5
Indicates whether the port interface is DTE or DCE. Options: dce (1) dte (2) Default Value: dce (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dce(1), dte(2)

cxMcPrtBopRtsDcdModemCtrl		1.3.6.1.4.1.495.2.1.1.1.5.1.1.6
Use the RTS or DCD modem control on the port. Options: on (1) vary (2) Default Value: on (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), vary(2)

cxMcPrtBopUseRtsDcdCndDataTx		1.3.6.1.4.1.495.2.1.1.1.5.1.1.7
Use the state of the RTS or DCD modem control when the port selected is conditioned by the presence of data in output queue. Options: no (1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBopUseRtsDcdCndLnk		1.3.6.1.4.1.495.2.1.1.1.5.1.1.8
Use the state of the RTS or DCD modem control when the port selected is conditioned by the main link status. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBopUseRtsDcdCndRem		1.3.6.1.4.1.495.2.1.1.1.5.1.1.9
Use the state of the RTS or DCD modem control when the port selected is conditioned by the remote DCD or RTS. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBopDtrCtsModemCtrl		1.3.6.1.4.1.495.2.1.1.1.5.1.1.10
Use the DTR or CTS modem control on the port. Options: on (1) vary (2) Default Value: on (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), vary(2)

cxMcPrtBopUseDtrCtsCndRts		1.3.6.1.4.1.495.2.1.1.1.5.1.1.11
Use the state of the CTS modem control when the port selected is conditioned by the local RTS. Options: no (1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBopUseDtrCtsCndLnk		1.3.6.1.4.1.495.2.1.1.1.5.1.1.12
Use the state of the RTS or DCD modem control when the port selected is conditioned by the main link status. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBopUseDtrCtsCndRem		1.3.6.1.4.1.495.2.1.1.1.5.1.1.13
Use the state of the RTS or DCD modem control when the port selected is conditioned by the remote DCD or RTS. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBopLimitBeforeOut		1.3.6.1.4.1.495.2.1.1.1.5.1.1.14
The limit before activation of output for the port. Range of Values: HC600: 2-100, MC600: 5-4000 Default Value: HC600: 5, MC600: 15
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

cxMcPrtBopUseOutCndCtsDtrOn		1.3.6.1.4.1.495.2.1.1.1.5.1.1.15
Use the output enable on CTS or DTR modem control for the port. Options: no(1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBopUseInCndDcdRtsOn		1.3.6.1.4.1.495.2.1.1.1.5.1.1.16
Use the input enable on DCD or RTS modem control for the port. Options: no(1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBopSyncMode		1.3.6.1.4.1.495.2.1.1.1.5.1.1.17
The clock synchronization for the port. Options: normal (1) extern (2) Default Value: normal (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), extern(2)

cxMcPrtBopDataLifetime		1.3.6.1.4.1.495.2.1.1.1.5.1.1.18
The data lifetime in millisecond for the port. Range of Values: 1-60000 Default Value: 2000
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..60000

cxMcPrtBopUseClockSync		1.3.6.1.4.1.495.2.1.1.1.5.1.1.19
The clocks synchronization on the port. Options: no(1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBopUseFlowCtrlClock		1.3.6.1.4.1.495.2.1.1.1.5.1.1.20
Use the flow control by clocks for the synchronous port. Options: no(1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBopFlowCtrlRate		1.3.6.1.4.1.495.2.1.1.1.5.1.1.21
The flow control rate of the synchronous port. Range of Values: HC600: 300-5609, MC600: 110-9600 Default Value: HC600: 2400. MC600: 300 HC600 DEFVAL { 2400 } MC600 DEFVAL { 300 }
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

cxMcPrtBopLimitOutFlowCtrl		1.3.6.1.4.1.495.2.1.1.1.5.1.1.22
The limit before output flow control of the synchronous port. Range of Values: HC600: 1-100, MC600: 0-4000 Default Value: HC600: 15, MC600: 3
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

cxMcPrtBopLimitInFlowCtrl		1.3.6.1.4.1.495.2.1.1.1.5.1.1.23
The overflow limit before input flow control of the synchronous port. Ranges of Values: HC600: 1-100, MC600: 0-4000 Default Value: HC600: 32, MC600: 512
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

cxMcPrtBopCoding		1.3.6.1.4.1.495.2.1.1.1.5.1.1.24
The coding on the port for bit-oriented protocols. Options: nrz (1) nrzi (2) Default Value: nrz (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	nrz(1), nrzi(2)

cxMcPrtBopOutIdleState		1.3.6.1.4.1.495.2.1.1.1.5.1.1.25
The output idle state of the synchronous port. Options: flag (1) mark (2) Default Value: flag (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	flag(1), mark(2)

cxMcPrtBopDelayBeforeIdle		1.3.6.1.4.1.495.2.1.1.1.5.1.1.26
The delay between frames before idle for the port. Range of Values: 0-2000 Default Value: 0
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..2000

cxMcPrtBopOutPreambleLng		1.3.6.1.4.1.495.2.1.1.1.5.1.1.27
The output preamble length of the synchronous port. Options: zero (1): HC600 or MC600 one (2): HC600 only two (3): HC600 only four (4): HC600 only eight (5): HC600 only Default Value: zero (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

cxMcPrtAsyTable		1.3.6.1.4.1.495.2.1.1.1.5.2
cx Port Station MC600 Asy Driver Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CxMcPrtAsyEntry

cxMcPrtAsyEntry		1.3.6.1.4.1.495.2.1.1.1.5.2.1
cx Port Station MC600 Asy Driver Entry gives the state of the variables associated to the Asynchronous Protocol.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CxMcPrtAsyEntry

cxMcPrtAsyPortUsed		1.3.6.1.4.1.495.2.1.1.1.5.2.1.1
The current port number that is used by the ASY driver.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cxMcPrtAsyPortStatus		1.3.6.1.4.1.495.2.1.1.1.5.2.1.2
The port status for enabling or disabling the port. Options: disable (1) enable (2) Default Value: disable (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

cxMcPrtAsyComRate		1.3.6.1.4.1.495.2.1.1.1.5.2.1.3
The port communication rates. Range of Values: 110-128000 Default Value: 9600
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	110..128000

cxMcPrtAsyUseLnkErrPassthro		1.3.6.1.4.1.495.2.1.1.1.5.2.1.4
Use the link error pass through on the port. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtAsyInterface		1.3.6.1.4.1.495.2.1.1.1.5.2.1.5
The port interface to DTE or DCE. Options: dce (1) dte (2) Default Value: dce (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dce(1), dte(2)

cxMcPrtAsyRtsDcdModemCtrl		1.3.6.1.4.1.495.2.1.1.1.5.2.1.6
Use the RTS or DCD modem control on the port. Options: on (1) vary (2) Default Value: on (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), vary(2)

cxMcPrtAsyUseRtsDcdCndDataTx		1.3.6.1.4.1.495.2.1.1.1.5.2.1.7
Use the state of the RTS or DCD modem control when the port selected is conditioned by the presence of data in output queue. Options: no (1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtAsyUseRtsDcdCndLnk		1.3.6.1.4.1.495.2.1.1.1.5.2.1.8
Use the state of the RTS or DCD modem control when the port selected is conditioned by the main link status. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtAsyUseRtsDcdCndRem		1.3.6.1.4.1.495.2.1.1.1.5.2.1.9
Use the state of the RTS or DCD modem control when the port selected is conditioned by the remote DCD or RTS. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtAsyDtrCtsModemCtrl		1.3.6.1.4.1.495.2.1.1.1.5.2.1.10
Use the DTR or CTS modem control on the port. Options: on (1) vary (2) Default Value: on (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), vary(2)

cxMcPrtAsyUseDtrCtsCndRts		1.3.6.1.4.1.495.2.1.1.1.5.2.1.11
Use the state of the CTS modem control when the port selected is conditioned by the local RTS. Options: no (1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtAsyUseDtrCtsCndLnk		1.3.6.1.4.1.495.2.1.1.1.5.2.1.12
Use the state of the RTS or DCD modem control when the port selected is conditioned by the main link status. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtAsyUseDtrCtsCndRem		1.3.6.1.4.1.495.2.1.1.1.5.2.1.13
Use the state of the RTS or DCD modem control when the port selected is conditioned by the remote DCD or RTS. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtAsyLimitBeforeOut		1.3.6.1.4.1.495.2.1.1.1.5.2.1.14
The limit before activation of output for the port. Range of Values: 1-100 Default Value: 15
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

cxMcPrtAsyOutCndCtsDtrOn		1.3.6.1.4.1.495.2.1.1.1.5.2.1.15
Use the output enable on CTS or DTR modem control for the port. Options: no (1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtAsyInCndDcdRtsOn		1.3.6.1.4.1.495.2.1.1.1.5.2.1.16
Use the input enable on DCD or RTS modem control for the port. Options: no (1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtAsySyncMode		1.3.6.1.4.1.495.2.1.1.1.5.2.1.17
The clock synchronization for the port. Options: normal (1) extern (2) Default Value: normal (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), extern(2)

cxMcPrtAsyUseDataLifeLimited		1.3.6.1.4.1.495.2.1.1.1.5.2.1.18
Use the data lifetime limited on the asynchronous port. Options: no (1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtAsyDataLifetime		1.3.6.1.4.1.495.2.1.1.1.5.2.1.19
The data lifetime in milliseconds for the port. Range of Values: 1-60000 Default Value: 2000
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..60000

cxMcPrtAsyOutFlowCtrl		1.3.6.1.4.1.495.2.1.1.1.5.2.1.20
The output flow control of the asynchronous port. Options: disable (1) xonxoff (2) ctsdtr (3) Default Value: xonxoff (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), xonxoff(2), ctsdtr(3)

cxMcPrtAsyInFlowCtrl		1.3.6.1.4.1.495.2.1.1.1.5.2.1.21
The input flow control of the asynchronous port. Options: disable (1) xonxoff (2) ctsdtr (3) Default Value: xonxoff (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), xonxoff(2), ctsdtr(3)

cxMcPrtAsyXonChr		1.3.6.1.4.1.495.2.1.1.1.5.2.1.22
The XON character value of the asynchronous port. Range of Values: 0-255 Default Value: 17
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

cxMcPrtAsyXoffChr		1.3.6.1.4.1.495.2.1.1.1.5.2.1.23
The XOFF character value of the asynchronous port. Range of Values: 0-255 Default Value: 19
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

cxMcPrtAsyNbBitPerChr		1.3.6.1.4.1.495.2.1.1.1.5.2.1.24
The number of bits per character on the port. Options: six (1) seven (2) eight (3) Default Value: eight (3)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	six(1), seven(2), eight(3)

cxMcPrtAsyParity		1.3.6.1.4.1.495.2.1.1.1.5.2.1.25
The parity on the port. Options: none (1) even (2) odd (3) Default Value: none (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), even(2), odd(3)

cxMcPrtAsyNbStopBit		1.3.6.1.4.1.495.2.1.1.1.5.2.1.26
The number of stop bits per character on the asynchronous port. Options: one (1) onehalf (2) two (3) Default Value: one (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	one(1), onehalf(2), two(3)

cxMcPrtAsyUseFlushOutChr		1.3.6.1.4.1.495.2.1.1.1.5.2.1.27
The flush output on specific character on the asynchronous port. Options: no (1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtAsyFlushOutChr		1.3.6.1.4.1.495.2.1.1.1.5.2.1.28
The flush character on the asynchronous port. Range of Values: 0-255 Default Value: 127
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

cxMcPrtCopTable		1.3.6.1.4.1.495.2.1.1.1.5.3
cx Port Station MC600 Cop Driver Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CxMcPrtCopEntry

cxMcPrtCopEntry		1.3.6.1.4.1.495.2.1.1.1.5.3.1
cx Port Station MC600 Cop Driver Entry gives the state of the variables associated to the Character Oriented Protocol.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CxMcPrtCopEntry

cxMcPrtCopPortUsed		1.3.6.1.4.1.495.2.1.1.1.5.3.1.1
The current port number that is used by the COP Driver. Range of Values: 1-4
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

cxMcPrtCopPortStatus		1.3.6.1.4.1.495.2.1.1.1.5.3.1.2
The port status for enabling or disabling the port. Options: disable (1) enable (2) Default Value: disable (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

cxMcPrtCopComRate		1.3.6.1.4.1.495.2.1.1.1.5.3.1.3
The port communication rates. Range of Values: 110-128000 Default Value: 9600
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	110..128000

cxMcPrtCopUseLnkErrPassthro		1.3.6.1.4.1.495.2.1.1.1.5.3.1.4
Use the link error pass through on the port. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCopInterfaceType		1.3.6.1.4.1.495.2.1.1.1.5.3.1.5
The port interface type: DTE or DCE. Options: dce (1) dte (2) Default: dce (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dce(1), dte(2)

cxMcPrtCopRtsDcdModemCtrl		1.3.6.1.4.1.495.2.1.1.1.5.3.1.6
Use the RTS or DCD modem control on the port. Options on (1) vary (2) Default Value: on (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), vary(2)

cxMcPrtCopUseRtsDcdCndDataTx		1.3.6.1.4.1.495.2.1.1.1.5.3.1.7
Use the state of the RTS or DCD modem control when the port selected is conditioned by the presence of data in output queue. Options: no (1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCopUseRtsDcdCndLnk		1.3.6.1.4.1.495.2.1.1.1.5.3.1.8
Use the state of the RTS or DCD modem control when the port selected is conditioned by the main link status. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCopUseRtsDcdCndRem		1.3.6.1.4.1.495.2.1.1.1.5.3.1.9
Use the state of the RTS or DCD modem control when the port selected is conditioned by the remote DCD or RTS. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCopDtrCtsModemCtrl		1.3.6.1.4.1.495.2.1.1.1.5.3.1.10
Use the DTR or CTS modem control on the port. Options: on (1) vary (2) Default Value: on (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), vary(2)

cxMcPrtCopUseDtrCtsCndRts		1.3.6.1.4.1.495.2.1.1.1.5.3.1.11
Use the state of the CTS modem control when the port selected is conditioned by the local RTS. Options: no (1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCopUseDtrCtsCndLnk		1.3.6.1.4.1.495.2.1.1.1.5.3.1.12
Use the the RTS or DCD modem control when the port selected is conditioned by the main link status. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCopUseDtrCtsCndRem		1.3.6.1.4.1.495.2.1.1.1.5.3.1.13
Use the state of the RTS or DCD modem control when the port selected is conditioned by the remote DCD or RTS. Options: no (1) yes (2) Default Value: yes (2)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCopLimitBeforeOut		1.3.6.1.4.1.495.2.1.1.1.5.3.1.14
The limit before activation of output for the port. Range of Values: 5-4000 Default Value: 15
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	5..4000

cxMcPrtCopUseOutCndCtsDtrOn		1.3.6.1.4.1.495.2.1.1.1.5.3.1.15
The output enable on CTS or DTR modem control for the port. Options: no (1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCopUseInCndDcdRtsOn		1.3.6.1.4.1.495.2.1.1.1.5.3.1.16
The input enable on DCD or RTS modem control for the port. Options: no (1) yes (2) Default Value: no (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCopSyncMode		1.3.6.1.4.1.495.2.1.1.1.5.3.1.17
The clock synchronization for the port. Options: normal (1) extern (2) Default Value: normal (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), extern(2)

cxMcPrtCopDataLifetime		1.3.6.1.4.1.495.2.1.1.1.5.3.1.18
The data lifetime in milliseconds for the port. Range of Values: 1-60000
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..60000

cxMcPrtCopUseClockSync		1.3.6.1.4.1.495.2.1.1.1.5.3.1.19
The clocks synchronization on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCopUseFlowCtrlClock		1.3.6.1.4.1.495.2.1.1.1.5.3.1.20
The use of flow control by clocks of the synchronous port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCopFlowCtrlRate		1.3.6.1.4.1.495.2.1.1.1.5.3.1.21
The use of flow control rate of the synchronous port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	110..9600

cxMcPrtCopLimitOutFlowCtrl		1.3.6.1.4.1.495.2.1.1.1.5.3.1.22
The limit before output flow control of the synchronous port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..4000

cxMcPrtCopLimitInFlowCtrl		1.3.6.1.4.1.495.2.1.1.1.5.3.1.23
The overflow limit before input flow control for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..4000

cxMcPrtCopOutIdleState		1.3.6.1.4.1.495.2.1.1.1.5.3.1.24
The output idle state for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	space(1), mark(2)

cxMcPrtCopNbBitPerChr		1.3.6.1.4.1.495.2.1.1.1.5.3.1.25
The number of bits per character on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	six(1), seven(2), eight(3)

cxMcPrtCopParity		1.3.6.1.4.1.495.2.1.1.1.5.3.1.26
The parity on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), even(2), odd(3)

cxMcPrtCopSyncChrOne		1.3.6.1.4.1.495.2.1.1.1.5.3.1.27
The synchronization character number one for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

cxMcPrtCopSyncChrTwo		1.3.6.1.4.1.495.2.1.1.1.5.3.1.28
The synchronization character number two for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

cxMcPrtCopNbSyncChr		1.3.6.1.4.1.495.2.1.1.1.5.3.1.29
The number of synchronization character for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

cxMcPrtCopUseDesyncChr		1.3.6.1.4.1.495.2.1.1.1.5.3.1.30
Use the desynchronization character on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCopDesyncChr		1.3.6.1.4.1.495.2.1.1.1.5.3.1.31
The desynchronization character for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

cxMcPrtCopNbDesyncChr		1.3.6.1.4.1.495.2.1.1.1.5.3.1.32
The number of desynchronization character for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

cxMcPrtCopUseDesyncRtsFall		1.3.6.1.4.1.495.2.1.1.1.5.3.1.33
Use the desynchronization on RTS fall on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtCopBitSense		1.3.6.1.4.1.495.2.1.1.1.5.3.1.34
The bit sense on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), inverted(2)

cxMcPrtBsyTable		1.3.6.1.4.1.495.2.1.1.1.5.4
cx Port Station MC600 Bsy Driver Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CxMcPrtBsyEntry

cxMcPrtBsyEntry		1.3.6.1.4.1.495.2.1.1.1.5.4.1
cx Port Station MC600 Bsy Driver Entry gives the state of the variables associated to the Bi-synchronous Protocol.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CxMcPrtBsyEntry

cxMcPrtBsyPortUsed		1.3.6.1.4.1.495.2.1.1.1.5.4.1.1
The current port number that is used by the BSY Driver.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

cxMcPrtBsyPortStatus		1.3.6.1.4.1.495.2.1.1.1.5.4.1.2
The port status for enabling or disabling the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

cxMcPrtBsyComRate		1.3.6.1.4.1.495.2.1.1.1.5.4.1.3
The port communication rates.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	110..64000

cxMcPrtBsyUseLnkErrPassthro		1.3.6.1.4.1.495.2.1.1.1.5.4.1.4
Use the link error pass through on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBsyInterface		1.3.6.1.4.1.495.2.1.1.1.5.4.1.5
The port interface type: DTE or DCE.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dce(1), dte(2)

cxMcPrtBsyRtsDcdModemCtrl		1.3.6.1.4.1.495.2.1.1.1.5.4.1.6
Use the RTS or DCD modem control on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), vary(2)

cxMcPrtBsyUseRtsDcdCndDataTx		1.3.6.1.4.1.495.2.1.1.1.5.4.1.7
Use the state of the RTS or DCD modem control when the port selected is conditioned by the presence of data in output queue.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBsyUseRtsDcdCndLnk		1.3.6.1.4.1.495.2.1.1.1.5.4.1.8
Use the state of the RTS or DCD modem control when the port selected is conditioned by the main link status.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBsyUseRtsDcdCndRem		1.3.6.1.4.1.495.2.1.1.1.5.4.1.9
Use the state of the RTS or DCD modem control when the port selected is conditioned by the remote DCD or RTS.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBsyDtrCtsModemCtrl		1.3.6.1.4.1.495.2.1.1.1.5.4.1.10
Use the DTR or CTS modem control on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), vary(2)

cxMcPrtBsyUseDtrCtsCndRts		1.3.6.1.4.1.495.2.1.1.1.5.4.1.11
Use the state of the CTS modem control when the port selected is conditioned by the local RTS.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBsyUseDtrCtsCndLnk		1.3.6.1.4.1.495.2.1.1.1.5.4.1.12
Use the state of the RTS or DCD modem control when the port selected is conditioned by the main link status.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBsyUseDtrCtsCndRem		1.3.6.1.4.1.495.2.1.1.1.5.4.1.13
Use the state of the RTS or DCD modem control when the port selected is conditioned by the remote DCD or RTS.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBsyLimitBeforeOut		1.3.6.1.4.1.495.2.1.1.1.5.4.1.14
The limit before activation of output for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	5..4000

cxMcPrtBsyUseOutCndCtsDtrOn		1.3.6.1.4.1.495.2.1.1.1.5.4.1.15
Use the output enable on CTS or DTR modem control for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBsyUseInCndDcdRtsOn		1.3.6.1.4.1.495.2.1.1.1.5.4.1.16
Use the input enable on DCD or RTS modem control for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cxMcPrtBsySyncMode		1.3.6.1.4.1.495.2.1.1.1.5.4.1.17
The clock synchronization for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), extern(2)

cxMcPrtBsyDataLifetime		1.3.6.1.4.1.495.2.1.1.1.5.4.1.18
The data lifetime in milliseconds for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..60000

cxMcPrtBsyChrSet		1.3.6.1.4.1.495.2.1.1.1.5.4.1.19
The character set on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ebcdic(1), usaascii(2), trans(3)

cxMcPrtBsyParity		1.3.6.1.4.1.495.2.1.1.1.5.4.1.20
The parity on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), even(2), odd(3)

cxMcPrtBsyBlkChkChr		1.3.6.1.4.1.495.2.1.1.1.5.4.1.21
The block check character on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	crc(1), lrc(2)

cxMcPrtBsyNbSyncChr		1.3.6.1.4.1.495.2.1.1.1.5.4.1.22
The number of synchronization character for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	2..255

cxMcPrtBsyMaxFrameSize		1.3.6.1.4.1.495.2.1.1.1.5.4.1.23
The maximum frame size for the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..64000