CXGIM-MIB

File: CXGIM-MIB.mib (29601 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
CXProduct-SMI

Imported symbols

Counter OBJECT-TYPE DisplayString
cxGim SapIndex Alias
ThruputClass

Defined Types

PSapIndex  
INTEGER 0..255    

TypeIndex  
INTEGER 0..255    

DteIndex  
INTEGER 1..255    

SubRef  
INTEGER 0..255    

PacketSize  
INTEGER bytes16(4), bytes32(5), bytes64(6), bytes128(7), bytes256(8), bytes512(9), bytes1024(10), bytes2048(11), bytes4096(12)    

GimSapEntry  
SEQUENCE    
  gimSapType TypeIndex
  gimSapNumber PSapIndex
  gimSapRowStatus INTEGER
  gimSapAlias Alias
  gimSapCompanionAlias Alias
  gimSapInactivityTimer INTEGER
  gimSapProtocolId DisplayString
  gimSapAddress DisplayString
  gimSapControl INTEGER
  gimSapState INTEGER
  gimSapLinkState INTEGER
  gimSapTxFrames Counter
  gimSapRxFrames Counter
  gimSapTxOctets Counter
  gimSapRxOctets Counter
  gimSapOutSuccessfullConnects Counter
  gimSapOutUnsuccessfullConnects Counter
  gimSapInSuccessfullConnects Counter
  gimSapInUnsuccessfullConnects Counter
  gimSapUnopenedServiceDiscards Counter
  gimSapTxResets Counter
  gimSapRxResets Counter
  gimSapTxThruputClass ThruputClass
  gimSapRxThruputClass ThruputClass
  gimSapTxPacketSize PacketSize
  gimSapRxPacketSize PacketSize
  gimSapTxWindowSize INTEGER
  gimSapRxWindowSize INTEGER

GimSysRouteEntry  
SEQUENCE    
  gimSRSapType TypeIndex
  gimSRSapNumber SapIndex
  gimSRRowStatus INTEGER
  gimSRDestAlias Alias
  gimSRSubRef SubRef
  gimSRRouteStatus INTEGER
  gimSRClearStatus INTEGER

XimDteEntry  
SEQUENCE    
  ximDteSapNumber SapIndex
  ximDteDteNumber DteIndex
  ximDteRowStatus INTEGER
  ximDteCalledAddress DisplayString
  ximDteFacilityField DisplayString
  ximDteUserDataField DisplayString

Defined Values

gimSysRouteConnectInterval 1.3.6.1.4.1.495.2.1.6.55.1
Determines the number of seconds between attempts to establish a connection for a X25 system route. A connection is attempted only for defined non-connected routes. Range of Values: 10 - 900 seconds Default Value: 30 seconds Configuration Changed: administrative and operative
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..900  

gimMibLevel 1.3.6.1.4.1.495.2.1.6.55.2
Used to determine current MIB module release supported by the agent. Object is in decimal.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

gimSapTable 1.3.6.1.4.1.495.2.1.6.55.10
A table containing configuration information about each X25 convergence service access point. Service access points of this type exist at the upper interface of the X25 Convergence layer, and are used to communicate with the X25 or IAM layers.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GimSapEntry

gimSapEntry 1.3.6.1.4.1.495.2.1.6.55.10.1
Defines a row in the Service Access Point Configuration table. Each row contains the objects which are used to define a service access point upper interface of the X25 Convergence layer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GimSapEntry  

gimSapType 1.3.6.1.4.1.495.2.1.6.55.10.1.1
Identifies the type of this SAP (service access point) with a numerical value. Values are unique for each type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TypeIndex  

gimSapNumber 1.3.6.1.4.1.495.2.1.6.55.10.1.2
Identifies this SAP (service access point) with a numerical value. Values are unique for each service access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PSapIndex  

gimSapRowStatus 1.3.6.1.4.1.495.2.1.6.55.10.1.3
Determines the status of the objects in a table row. Options: invalid (1): Row is deleted from the table immediately, however values are still in effect until the next reset. valid (2): Use this value to add a new row to the table, or modify an existing row. Default Value: valid (2) Configuration Changed: administrative
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

gimSapAlias 1.3.6.1.4.1.495.2.1.6.55.10.1.4
Identifies this service access point by a textual name. Names must be unique across all service access points at all layers. Range of Values: 1 -16 alphanumeric characters (first character must be a letter) Default Value: none Configuration Changed: administrative
Status: mandatory Access: read-write
OBJECT-TYPE    
  Alias  

gimSapCompanionAlias 1.3.6.1.4.1.495.2.1.6.55.10.1.5
Determines the name which uniquely identifies the X.25 Upper SAP (service access point) which will communicate with this SAP. Range of Values: 1 -16 alphanumeric characters (first character must be a letter) Default Value: none Configuration Changed: administrative
Status: mandatory Access: read-write
OBJECT-TYPE    
  Alias  

gimSapInactivityTimer 1.3.6.1.4.1.495.2.1.6.55.10.1.6
Defines the time of inactivity, in seconds, after which the SAP (service access point) will send a disconnect request to the X25 layer. The timer starts whenever data is received from the X25 layer or the IAM layer. Range of Values: 0 to 3600 Note: A value of 0 means that the timer is disabled. The circuit is permanently open. Default Value: 90 Configuration Changed: Operative
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..3600  

gimSapProtocolId 1.3.6.1.4.1.495.2.1.6.55.10.1.7
Defines the protocol format that is used for incoming call or call request packets to the X.25 call data field. The field consists of 4 hexadecimal octets where the first octet is coded as follows: ASYNC PAD bits 8 & 7 - 00 for CCITT use - 01 for national use - 10 reserved for international user bodies - 11 for DTE-DTE use When bits 8 & 7 are equal to 00, bits 6 to 1 will be equal to 000001. The first octet is shown as 01, 00, 00, 00. The first 0 in each number is optional and may be shown as 1, 0, 0, 0. IP over X.25 The value hex CC is required for IP. All bits of octets 2, 3 and 4 are set to 0. They are reserved as a future mechanism for providing the called PAD or packet mode DTE (user) with additional information pertaining to the calling party. A value of 00,00,00,00 will disable the protocol id formatting for x.25 call request packet or validation for incoming call. Default Value: 01,00,00,00 Configuration Changed: Operative
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(7..11)  

gimSapAddress 1.3.6.1.4.1.495.2.1.6.55.10.1.8
Defines the calling address for this SAP (service access point). Range of Values: 1 to 15 digits Default Value: 0 Configuration Changed: Operative
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

gimSapControl 1.3.6.1.4.1.495.2.1.6.55.10.1.10
Permits control of a specific SAP (service access point). Options: clearStats (1): Clear all statistics stored by statistics objects. Configuration Changed: operative
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clearStats(1)  

gimSapState 1.3.6.1.4.1.495.2.1.6.55.10.1.12
Indicates the current state of this SAP (service access point). Options: offLine (1): Indicates a newly created service access point whose configuration has not yet been sent to the X25 Convergence layer. unbound (2): SAP is not yet bound to its companion SAP at an upper layer. notConnected (3): The associated route with this SAP is not connected, or there is no route associated with this SAP. inProgress (4): The associated route is in the process of connecting. connected (5): The associated route is connected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offLine(1), unbound(2), notConnected(3), inProgress(4), connected(5)  

gimSapLinkState 1.3.6.1.4.1.495.2.1.6.55.10.1.13
Indicates the current state of the x25 link for this SAP (service access point). Options: notConnected (1): There is no x25 circuit established associated with this SAP. inProgress (2): The associated x25 call is in the process of being established. connected (3): The associated x25 call is established.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notConnected(1), inProgress(2), connected(3)  

gimSapTxFrames 1.3.6.1.4.1.495.2.1.6.55.10.1.15
Indicates the number of frames transmitted by this service access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

gimSapRxFrames 1.3.6.1.4.1.495.2.1.6.55.10.1.16
Indicates the number of frames received by this service access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

gimSapTxOctets 1.3.6.1.4.1.495.2.1.6.55.10.1.17
Indicates the number of octets transmitted by this service access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

gimSapRxOctets 1.3.6.1.4.1.495.2.1.6.55.10.1.18
Indicates the number of octets received by this service access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

gimSapOutSuccessfullConnects 1.3.6.1.4.1.495.2.1.6.55.10.1.19
Indicates the number of successful outgoing connections established by this SAP (service access point). An outgoing connection is always attempted from X25 convergence to the Inter-Application Module (IAM). At the PSAP, this object represents the total number of outgoing connections established by all SAPs. At each individual SAP, this object represents the number of outgoing connections established by only that SAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

gimSapOutUnsuccessfullConnects 1.3.6.1.4.1.495.2.1.6.55.10.1.20
Indicates the number of unsuccessful outgoing connections attempted by this SAP (service access point). An outgoing connection is always attempted from X25 convergence to the Inter-Application Module (IAM). At the PSAP, this object represents the total number of unsuccessful outgoing connections attempted by all SAPs. At each individual SAP, this object represents the number of unsuccessful outgoing connections attempted by only that SAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

gimSapInSuccessfullConnects 1.3.6.1.4.1.495.2.1.6.55.10.1.21
Indicates the number of successful incoming connections established at this SAP (service access point). An incoming connection is always attempted from the Inter-Application Module (IAM) to X25 convergence. At the PSAP, this object represents the total number of successful incoming connections for all SAPs. At each individual SAP, this object represents the number of successful incoming connections for only that SAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

gimSapInUnsuccessfullConnects 1.3.6.1.4.1.495.2.1.6.55.10.1.22
Indicates the number of unsuccessful incoming connections attempted at this SAP (service access point). An incoming connection is always attempted from the Inter-Application Module (IAM) to X25 convergence. At the PSAP, this object represents the total number of unsuccessful incoming connections for all SAPs. At each individual SAP, this object represents the number of unsuccessful incoming connections for only that SAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

gimSapUnopenedServiceDiscards 1.3.6.1.4.1.495.2.1.6.55.10.1.23
This object applies only to the PSAP (public service access point). Indicates the number of frames received and discarded by the PSAP because: - no route was associated with the frame - the frame was destined for a route that is not connected
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

gimSapTxResets 1.3.6.1.4.1.495.2.1.6.55.10.1.24
This object applies only to the PSAP (public service access point). Indicates the number of Inter- Application Module (IAM) reset frames sent by the PSAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

gimSapRxResets 1.3.6.1.4.1.495.2.1.6.55.10.1.25
This object applies only to the PSAP. Indicates the number of Inter- Application Module (IAM) reset frames received by the PSAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

gimSapRxThruputClass 1.3.6.1.4.1.495.2.1.6.55.10.1.50
Defines the default receive throughput class that is used at this SAP (service access point). Range of Values: 75 - 64000 bps Default Value: 9600 bps Configuration Changed: Operative
Status: mandatory Access: read-write
OBJECT-TYPE    
  ThruputClass  

gimSapTxThruputClass 1.3.6.1.4.1.495.2.1.6.55.10.1.51
Defines the default transmit throughput class that is used at this SAP (service access point). Range of Values: 75 to 64000 bps Default Value: 9600 bps Configuration Changed: Operative
Status: mandatory Access: read-write
OBJECT-TYPE    
  ThruputClass  

gimSapTxPacketSize 1.3.6.1.4.1.495.2.1.6.55.10.1.52
Defines the size of the transmit packet for the Xim layer. Range of Values: 16 to 4096 bytes Default Value: 128 bytes Configuration Changed: Operative
Status: mandatory Access: read-write
OBJECT-TYPE    
  PacketSize  

gimSapRxPacketSize 1.3.6.1.4.1.495.2.1.6.55.10.1.53
Defines the size of the receive packet for the Xim layer. Range of Values: 16 to 4096 bytes Default Value: 128 bytes Configuration Changed: Operative
Status: mandatory Access: read-write
OBJECT-TYPE    
  PacketSize  

gimSapTxWindowSize 1.3.6.1.4.1.495.2.1.6.55.10.1.54
Defines the size of the transmit window for the Xim layer. Range of Values: 1 to 127 Default Value: 2 Configuration Changed: Operative
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..127  

gimSapRxWindowSize 1.3.6.1.4.1.495.2.1.6.55.10.1.55
Defines the size of the receive window for the Xim layer. Range of Values: 1 to 127 Default Value: 2 Configuration Changed: Operative
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..127  

gimSysRouteTable 1.3.6.1.4.1.495.2.1.6.55.11
A table containing information about each X25 system route. Routes allow this X25 layer to link with another X25 layer across a frame relay network, or with the X25 layer on another similar card in the same chassis (for future use with the CX1000).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GimSysRouteEntry

gimSysRouteEntry 1.3.6.1.4.1.495.2.1.6.55.11.1
Defines a row in the gimSysRouteTable. Each row contains the objects which define a system route.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GimSysRouteEntry  

gimSRSapType 1.3.6.1.4.1.495.2.1.6.55.11.1.1
Identifies the type of service access point this route entry is associated with.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TypeIndex  

gimSRSapNumber 1.3.6.1.4.1.495.2.1.6.55.11.1.2
Identifies the service access point this route entry is associated with.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SapIndex  

gimSRRowStatus 1.3.6.1.4.1.495.2.1.6.55.11.1.3
Determines the status of the objects in a table row. Options: invalid (1): Row is deleted from the table immediately, however values are still in effect until the next reset. valid (2): Use this value to add a new row to the table, or modify an existing row. Default Value: none Configuration Changed: administrative and operative
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

gimSRDestAlias 1.3.6.1.4.1.495.2.1.6.55.11.1.4
Determines the textual name of the destination service this route connects to. When attempting a X25 connection across Frame Relay, this object specifies the name of the outgoing circuit at the Frame Relay layer. When attempting a X25 connection between cards within the same chassis (future use within CX1000), this object specifies the name of the X25 Convergence SAP on the remote card. Range of Values: 1 -16 characters (first character must be a letter) Default Value: none Configuration Changed: administrative and operative
Status: mandatory Access: read-write
OBJECT-TYPE    
  Alias  

gimSRSubRef 1.3.6.1.4.1.495.2.1.6.55.11.1.5
Specifies a reference number that uniquely identifies this route. This number is used by the FRIM (Frame Relay Interface Module) to identify routes using the same DLCI (enables PVC consolidation). This number must be unique for all routes sharing the same DLCI. Range of Values: 1 - 255 (when using PVC consolidation) 0 (when not using PVC consolidation) Default Value: 0 Configuration Changed: administrative and operative
Status: mandatory Access: read-write
OBJECT-TYPE    
  SubRef  

gimSRRouteStatus 1.3.6.1.4.1.495.2.1.6.55.11.1.10
Indicates the connection status of this X25 route. Options: offLine (1): Indicates that the X25 Convergence SAP this route is associated with does not exist or is offline. notConnected (2): Indicates that the remote destination does not exist, or has refused the connection. inProgress (3): Indicates that the connection is in the process of being established. This is a transient state. connected (4): Indicates that the connection is established and is ready for data transfer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offLine(1), notConnected(2), inProgress(3), connected(4)  

gimSRClearStatus 1.3.6.1.4.1.495.2.1.6.55.11.1.11
Indicates the status of a failed connection. The value of this object is only valid only between attempts to establish the route connection (gimSRRouteStatus = notConnected), and may or may not change after successive failed attempts. Options: noFailure (1): Once a system route has been successfully connected, this value is maintained for the duration of the connection. internalError (2): An internal error has occurred. localAllocFailure (3): There is insufficient memory available for X25 Convergence to establish this connection. remoteAllocFailure (4): There is insufficient memory available for the destination protocol layer to establish this connection. localNoAccess (5): This route is associated with a SAP that does not exist. remoteNoAccess (6): This route is associated with a SAP that does not exist at the destination layer. localPvcDown (7): For future use. remotePvcDown (8): The PVC at the destination protocol layer is down. localPvcBusy (9): The SAP associated with this route is already connected. remotePvcBusy (10): The destination associated with this route is already connected. This typically occurs when the route is a non-MPE (PVC consolidating) circuit. localFcnFailure (11): Flow control negotiation failed. remoteFcnFailure (12): Flow control negotiation failed at the destination protocol layer. localDsnFailure (13): Data size negotiation failed. localRefInUse (14): Data size negotiation failed at the destination protocol layer. remoteAliasNotFound (15): The destination alias (gimSRDestAlias) does not exist. remoteNoPvcService (16): The destination protocol layer does not support PVC service. mpeInvalidSubref (17): The value of gimSRSubRef is invalid at the destination protocol layer. (i.e., lapcnvSRSubRef is set to '0' and the destination frame relay circuit is configured for PVC consolidation).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noFailure(1), internalError(2), localAllocFailure(3), remoteAllocFailure(4), localNoAccess(5), remoteNoAccess(6), localPvcDown(7), remotePvcDown(8), localPvcBusy(9), remotePvcBusy(10), localFcnFailure(11), remoteFcnFailure(12), localDsnFailure(13), localRefInUse(14), remoteAliasNotFound(15), remoteNoPvcService(16), mpeInvalidSubref(17)  

ximDteTable 1.3.6.1.4.1.495.2.1.6.55.12
A table containing the DTE X.28 Selection command objects for each defined 'abbreviated address'.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XimDteEntry

ximDteEntry 1.3.6.1.4.1.495.2.1.6.55.12.1
The objects for a specific DTE X.28 Selection entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  XimDteEntry  

ximDteSapNumber 1.3.6.1.4.1.495.2.1.6.55.12.1.1
Associates the DTE entries defined by the object 'ximDteDteNumber' with an xim sap number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SapIndex  

ximDteDteNumber 1.3.6.1.4.1.495.2.1.6.55.12.1.2
Associates this DTE entry with the xim sap number defined by the object 'ximDteSapNumber', Currently the XIM will support ONLY one entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DteIndex  

ximDteRowStatus 1.3.6.1.4.1.495.2.1.6.55.12.1.3
Indicates whether this specific entry is configured within the MIB. Entries (rows) may be created by setting this object value to 'valid', or deleted by changing this object value to 'invalid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

ximDteCalledAddress 1.3.6.1.4.1.495.2.1.6.55.12.1.5
Defines the network address of a remote device for this DTE entry. Allowable values: 1 to 15 numerical digits.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

ximDteFacilityField 1.3.6.1.4.1.495.2.1.6.55.12.1.12
Defines the facility codes and parameters requires for the X.28 Selection command for this DTE entry. The facility codes and parameters must be entered as defined in the CCITT X.28 Recommendation. The following facilities are supported: - Reverse charge ('R') A value of null string (blank) means no facilities.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

ximDteUserDataField 1.3.6.1.4.1.495.2.1.6.55.12.1.13
Defines the user data field of the X.28 Selection command for this DTE entry. A value of nul string (blank) means no user data.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..12)