CXDDS-MIB

File: CXDDS-MIB.mib (14239 bytes)

Imported modules

RFC-1212	RFC-1215	RFC1213-MIB
CXProduct-SMI

Imported symbols

OBJECT-TYPE	TRAP-TYPE	DisplayString
cxDds	SapIndex	Alias

Defined Types

DdsSlotEntry
SEQUENCE
	ddsSlotNumber	SapIndex
	ddsSlotAlias	Alias
	ddsSlotRowStatus	INTEGER
	ddsSlotStatus	INTEGER
	ddsSlotConfigLineType	INTEGER
	ddsSlotConfigLineService	INTEGER
	ddsSlotConfigRemLoop2LocalAddress	INTEGER
	ddsSlotConfigRemLoop2RemoteAddress	INTEGER
	ddsSlotConfigLoopback	INTEGER
	ddsSlotConfigPatternGen	INTEGER
	ddsSlotDialNumber	DisplayString
	ddsSlotSoftwareRevision	INTEGER
	ddsSlotStuffingOption	INTEGER
	ddsSlotLineQuality	INTEGER
	ddsSlotLineRelativeReceiveLevelMin	INTEGER
	ddsSlotLineRelativeReceiveLevelMax	INTEGER
	ddsSlotLineLoopback	INTEGER
	ddsSlotResultErtPatternDetect	INTEGER
	ddsSlotResultPatternGen	INTEGER
	ddsSlotResultDialing	INTEGER
	ddsSlotModel	INTEGER
	ddsSlotRevision	INTEGER
	ddsSlotEco	INTEGER
	ddsSlotLineTrap	INTEGER
	ddsSlotLoopTrap	INTEGER

Defined Values

ddsSlotTable		1.3.6.1.4.1.495.2.1.6.39.1
Identifies the configuration information for a specific DDS access point and its associated hardware port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DdsSlotEntry

ddsSlotEntry		1.3.6.1.4.1.495.2.1.6.39.1.1
Identifies the configuration information for a specific DDS access point and its associated hardware port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	DdsSlotEntry

ddsSlotNumber		1.3.6.1.4.1.495.2.1.6.39.1.1.1
Identifies a DDS access point by a numerical value. Each DDS access point has a unique value.
Status: mandatory	Access: read-only
OBJECT-TYPE
	SapIndex

ddsSlotAlias		1.3.6.1.4.1.495.2.1.6.39.1.1.2
Assigns a textual name to the DDS access point. Each access point requires a unique name. You may not assign the same name twice. Default Value: none Range of Values: up to 12 alphanumeric characters, the first must be a letter. Configuration Changed: operative
Status: mandatory	Access: read-write
OBJECT-TYPE
	Alias

ddsSlotRowStatus		1.3.6.1.4.1.495.2.1.6.39.1.1.3
Determines the status of the objects in a row. Default Value: valid Options: invalid (1): row is flagged, after next reset the values will be disabled and the row will be deleted from the table valid (2): values are enabled Configuration Changed: administrative
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	invalid(1), valid(2)

ddsSlotStatus		1.3.6.1.4.1.495.2.1.6.39.1.1.4
Identifies the status of the DDS option card as present, not present or present but failed. Default Value: none Options: dds-not-present (1) dds-present (2) dds-present-failed (3)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	dds-not-present(1), dds-present(2), dds-present-failed(3)

ddsSlotConfigLineType		1.3.6.1.4.1.495.2.1.6.39.1.1.5
Assigns the DDS line configuration. Default Value: telco-point-to-point (1) Options: telco-point-to-point (1) telco-multipoint (2) idm-timing-slave (3) idm-timing-master (4) Configuration Changed: operative
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	telco-point-to-point(1), telco-multipt(2), ldm-timing-slave(3), ldm-timing-master(4)

ddsSlotConfigLineService		1.3.6.1.4.1.495.2.1.6.39.1.1.6
Assigns the DDS line service type. Default Value: dds-56K (2) Range of Values: clear-channel-64K (1) switched-56K (2) dds-56K (3) dds-19200 (4) dds-9600 (5) dds-4800 (6) dds-2400 (7) dds-1200 (8) Configuration Changed: operative
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	clear-channel-64K(1), switched-56K(2), dds-56K(3), dds-19200(4), dds-9600(5), dds-4800(6), dds-2400(7)

ddsSlotConfigLoopback		1.3.6.1.4.1.495.2.1.6.39.1.1.7
Specifies the DDS loopback type. Default Value: no-loopback (1) Range of Values: no-loopback (1) dte-loopback (2) loop2 (3), loop3 (4), loop4 (5) remote-loop2 (6) Configuration Changed: operative
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no-loopback(1), dte-loopback(2), loop2(3), loop3(4), loop4(5), remote-loop2(6)

ddsSlotConfigRemLoop2LocalAddress		1.3.6.1.4.1.495.2.1.6.39.1.1.8
Specifies the local address for V.54 remote loop2. Default Value: none Range of Values: 0 to 255 The 34 valid V.54 hex addresses include: 0x01, 0x03, 0x05, 0x07, 0x09, 0x0B, 0x0D, 0x0F, 0x11, 0x13, 0x15, 0x17, 0x19, 0x1B, 0x1D, 0x1F, 0x25, 0x27, 0x2B, 0x2D, 0x2F, 0x33, 0x35, 0x37, 0x3B, 0x3D, 0x3F, 0x55, 0x57, 0x5B, 0x5F, 0x6F, 0x77, 0x7F Configuration Changed: operative
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

ddsSlotConfigRemLoop2RemoteAddress		1.3.6.1.4.1.495.2.1.6.39.1.1.9
Specifies the remote address for V.54 remote loop2. Range of Values: 0 to 255 Default Value: none Configuration Changed: operative
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

ddsSlotConfigPatternGen		1.3.6.1.4.1.495.2.1.6.39.1.1.10
Specifies the type of pattern generated. Range of Values: no-pattern (1) pattern-511 (2) pattern-511-with-errors (3) Default Value: no-pattern (1) Configuration Changed: operative
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no-pattern(1), pattern-511(2), pattern-511-with-errors(3)

ddsSlotDialNumber		1.3.6.1.4.1.495.2.1.6.39.1.1.11
Assigns the dial number for switched56 applications. Default Value: none Range of Values: 12 character octet string Configuration Changed: operative
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..11)

ddsSlotSoftwareRevision		1.3.6.1.4.1.495.2.1.6.39.1.1.12
Indicates the DDS firmware revision as an integer value from 0 to 255. Default Value: none Range of Values: 0-255
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

ddsSlotStuffingOption		1.3.6.1.4.1.495.2.1.6.39.1.1.13
Identifies whether the clear channel chip (ccc) option (for 64K clear channel) is installed. Default Value: none Options: ccc-installed (1) ccc-not-installed (2)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ccc-installed(1), ccc-not-installed(2)

ddsSlotLineQuality		1.3.6.1.4.1.495.2.1.6.39.1.1.14
Identifies whether the link is up, if no link exists or if a network error (OOS - out of service) has occurred. Default Value: none Options: link (1) no-link (2) network-error-oos (3)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	link(1), no-link(2), network-error-oos(3)

ddsSlotLineRelativeReceiveLevelMin		1.3.6.1.4.1.495.2.1.6.39.1.1.15
Indicates the minimum relative receive line level. Default Value: none Range of Values: 0-255
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

ddsSlotLineRelativeReceiveLevelMax		1.3.6.1.4.1.495.2.1.6.39.1.1.16
Indicates the maximum relative receive line level. Default Value: none Range of Values: 0-255
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

ddsSlotLineLoopback		1.3.6.1.4.1.495.2.1.6.39.1.1.17
Indicates the loopback status of the line. Options: none (1) csu-loopback (2) dsu-loopback (3) dte-loopback (4) loop2 (5) loop3 (6) loop4 (7) remote-loop2 (8) Default Value: none (1)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), csu-loopback(2), dsu-loopback(3), dte-loopback(4), loop2(5), loop3(6), loop4(7), remote-loop2(8)

ddsSlotResultErtPatternDetect		1.3.6.1.4.1.495.2.1.6.39.1.1.18
Identifies the reception of the 511 bit pattern or not. Options: not-receiving-pattern (1) receiving-pattern (2) receiving-patt-with-errors (3) Default Value: none
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	not-receiving-pattern(1), receiving-pattern(2), receiving-patt-with-errors(3)

ddsSlotResultPatternGen		1.3.6.1.4.1.495.2.1.6.39.1.1.19
Identifies what type of pattern the DDS is generating on the line. Options: no-pattern (1) ert-pattern (2) ert-with-errors (3) Default: none
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	no-pattern(1), ert-pattern(2), ert-with-errors(3)

ddsSlotResultDialing		1.3.6.1.4.1.495.2.1.6.39.1.1.20
Indicates the dialing result codes for switched56 service as: dialing, connection made, the connection is not switched56, that a number has not been supplied by the host, no link available, no wink available, wink invalid or no answer. Options: dialing-idle (1) dialing-now (2) connection-made (3) err-no-num-from-host (4) err-no-link (5) err-no-rx-idle (6) err-no-wink (7) err-invalid-wink (8) err-no-answer (9) Default Value: none
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	dialing-idle(1), dialing-now(2), connection-made(3), err-no-num-from-host(4), err-no-link(5), err-no-rx-idle(6), err-no-wink(7), err-invalid-wink(8), err-no-answer(9)

ddsSlotModel		1.3.6.1.4.1.495.2.1.6.39.1.1.21
Indicates the Printed Circuit Board (PCB) model number . Range of Values: 0-7 Default: none
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..7

ddsSlotRevision		1.3.6.1.4.1.495.2.1.6.39.1.1.22
Indicates the PCB revision level. Range of Values: 0-15 Default Value: none
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..15

ddsSlotEco		1.3.6.1.4.1.495.2.1.6.39.1.1.23
Indicates the PCB Engineering Change Order (ECO) level. Range of Values: 0-15 Default Value: none
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..15

ddsSlotLineTrap		1.3.6.1.4.1.495.2.1.6.39.1.1.24
Determines the status of the line trap. Options: disabled (1) enabled (2) Default Value: disabled (1) Configuration Changed: operative
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

ddsSlotLoopTrap		1.3.6.1.4.1.495.2.1.6.39.1.1.25
Determines the status of the loopback change trap. Range of Values: disabled (1) enabled (2) Default Value: disabled (1) Configuration Changed: operative
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

ddsSlotLineStatusChange		1
Indicates that an alarm has occurred. The line quality currently in use at the DDS access point has changed state to any of the states defined in object ddsSlotLineQuality.
TRAP-TYPE

ddsSlotLoopStatusChange		2
Indicates an alarm status has occurred. The loopback status currently in use at the DDS access point has changed state to any of the states defined in object ddsSlotLineLoopback.
TRAP-TYPE