CTRON-IPX-ROUTER-MIB

File: CTRON-IPX-ROUTER-MIB.mib (183947 bytes)

Imported modules

RFC-1212 RFC1213-MIB BRIDGE-MIB
ROUTER-OIDS RFC1155-SMI

Imported symbols

OBJECT-TYPE DisplayString PhysAddress
MacAddress nwRtrProtoSuites Counter
TimeTicks Gauge

Defined Types

IpxAddress  
STRING    

NwIpxFwdIfEntry  
SEQUENCE    
  nwIpxFwdIfIndex INTEGER
  nwIpxFwdIfAdminStatus INTEGER
  nwIpxFwdIfOperStatus INTEGER
  nwIpxFwdIfOperationalTime TimeTicks
  nwIpxFwdIfControl INTEGER
  nwIpxFwdIfMtu INTEGER
  nwIpxFwdIfForwarding INTEGER
  nwIpxFwdIfFrameType INTEGER
  nwIpxFwdIfAclIdentifier INTEGER
  nwIpxFwdIfAclStatus INTEGER
  nwIpxFwdIfCacheControl INTEGER
  nwIpxFwdIfCacheEntries Counter
  nwIpxFwdIfCacheHits Counter
  nwIpxFwdIfCacheMisses Counter

NwIpxAddrEntry  
SEQUENCE    
  nwIpxAddrIfIndex INTEGER
  nwIpxAddrIfAddress IpxAddress
  nwIpxAddrIfControl INTEGER
  nwIpxAddrIfAddrType INTEGER

NwIpxFwdIfCtrEntry  
SEQUENCE    
  nwIpxFwdIfCtrIfIndex INTEGER
  nwIpxFwdIfCtrAdminStatus INTEGER
  nwIpxFwdIfCtrReset INTEGER
  nwIpxFwdIfCtrOperationalTime TimeTicks
  nwIpxFwdIfCtrInPkts Counter
  nwIpxFwdIfCtrOutPkts Counter
  nwIpxFwdIfCtrFwdPkts Counter
  nwIpxFwdIfCtrFilteredPkts Counter
  nwIpxFwdIfCtrDiscardPkts Counter
  nwIpxFwdIfCtrAddrErrPkts Counter
  nwIpxFwdIfCtrLenErrPkts Counter
  nwIpxFwdIfCtrHdrErrPkts Counter
  nwIpxFwdIfCtrInBytes Counter
  nwIpxFwdIfCtrOutBytes Counter
  nwIpxFwdIfCtrFwdBytes Counter
  nwIpxFwdIfCtrFilteredBytes Counter
  nwIpxFwdIfCtrDiscardBytes Counter
  nwIpxFwdIfCtrHostInPkts Counter
  nwIpxFwdIfCtrHostOutPkts Counter
  nwIpxFwdIfCtrHostDiscardPkts Counter
  nwIpxFwdIfCtrHostInBytes Counter
  nwIpxFwdIfCtrHostOutBytes Counter
  nwIpxFwdIfCtrHostDiscardBytes Counter

NwIpxRipIfEntry  
SEQUENCE    
  nwIpxRipIfIndex INTEGER
  nwIpxRipIfAdminStatus INTEGER
  nwIpxRipIfOperStatus INTEGER
  nwIpxRipIfOperationalTime TimeTicks
  nwIpxRipIfVersion INTEGER
  nwIpxRipIfAdvertisement INTEGER
  nwIpxRipIfFloodDelay INTEGER
  nwIpxRipIfRequestDelay INTEGER
  nwIpxRipIfPriority INTEGER
  nwIpxRipIfHelloTimer INTEGER
  nwIpxRipIfSplitHorizon INTEGER
  nwIpxRipIfPoisonReverse INTEGER
  nwIpxRipIfSnooping INTEGER
  nwIpxRipIfType INTEGER
  nwIpxRipIfXmitCost INTEGER
  nwIpxRipIfAclIdentifier INTEGER
  nwIpxRipIfAclStatus INTEGER

NwIpxRipIfCtrEntry  
SEQUENCE    
  nwIpxRipIfCtrIfIndex INTEGER
  nwIpxRipIfCtrAdminStatus INTEGER
  nwIpxRipIfCtrReset INTEGER
  nwIpxRipIfCtrOperationalTime TimeTicks
  nwIpxRipIfCtrInPkts Counter
  nwIpxRipIfCtrOutPkts Counter
  nwIpxRipIfCtrFilteredPkts Counter
  nwIpxRipIfCtrDiscardPkts Counter
  nwIpxRipIfCtrInBytes Counter
  nwIpxRipIfCtrOutBytes Counter
  nwIpxRipIfCtrFilteredBytes Counter
  nwIpxRipIfCtrDiscardBytes Counter

NwIpxRipRouteEntry  
SEQUENCE    
  nwIpxRipRtNetId IpxAddress
  nwIpxRipRtIfIndex INTEGER
  nwIpxRipRtSrcNode IpxAddress
  nwIpxRipRtHops INTEGER
  nwIpxRipRtTicks INTEGER
  nwIpxRipRtAge INTEGER
  nwIpxRipRtType INTEGER
  nwIpxRipRtFlags INTEGER

NwIpxSapIfEntry  
SEQUENCE    
  nwIpxSapIfIndex INTEGER
  nwIpxSapIfAdminStatus INTEGER
  nwIpxSapIfOperStatus INTEGER
  nwIpxSapIfOperationalTime TimeTicks
  nwIpxSapIfVersion INTEGER
  nwIpxSapIfAdvertisement INTEGER
  nwIpxSapIfFloodDelay INTEGER
  nwIpxSapIfRequestDelay INTEGER
  nwIpxSapIfPriority INTEGER
  nwIpxSapIfHelloTimer INTEGER
  nwIpxSapIfSplitHorizon INTEGER
  nwIpxSapIfPoisonReverse INTEGER
  nwIpxSapIfSnooping INTEGER
  nwIpxSapIfType INTEGER
  nwIpxSapIfXmitCost INTEGER
  nwIpxSapIfAclIdentifier INTEGER
  nwIpxSapIfAclStatus INTEGER

NwIpxSapIfCtrEntry  
SEQUENCE    
  nwIpxSapIfCtrIfIndex INTEGER
  nwIpxSapIfCtrAdminStatus INTEGER
  nwIpxSapIfCtrReset INTEGER
  nwIpxSapIfCtrOperationalTime TimeTicks
  nwIpxSapIfCtrInPkts Counter
  nwIpxSapIfCtrOutPkts Counter
  nwIpxSapIfCtrFilteredPkts Counter
  nwIpxSapIfCtrDiscardPkts Counter
  nwIpxSapIfCtrInBytes Counter
  nwIpxSapIfCtrOutBytes Counter
  nwIpxSapIfCtrFilteredBytes Counter
  nwIpxSapIfCtrDiscardBytes Counter

NwIpxSapServerIfEntry  
SEQUENCE    
  nwIpxSapServerIfNetId IpxAddress
  nwIpxSapServerIfNode STRING
  nwIpxSapServerIfSocket STRING
  nwIpxSapServerIfServiceType INTEGER
  nwIpxSapServerIfIfNum INTEGER
  nwIpxSapServerIfSrcNode STRING
  nwIpxSapServerIfName STRING
  nwIpxSapServerIfHops INTEGER
  nwIpxSapServerIfAge INTEGER
  nwIpxSapServerIfType INTEGER
  nwIpxSapServerIfFlags INTEGER

NwIpxFibEntry  
SEQUENCE    
  nwIpxFibNetId IpxAddress
  nwIpxFibHops INTEGER
  nwIpxFibTimeTicks TimeTicks
  nwIpxFibNextHopIf INTEGER
  nwIpxFibNextHopNet STRING
  nwIpxFibNextHopNode MacAddress
  nwIpxFibRouteType INTEGER

NwIpxAclEntry  
SEQUENCE    
  nwIpxAclIdentifier INTEGER
  nwIpxAclSequence INTEGER
  nwIpxAclPermission INTEGER
  nwIpxAclMatches Counter
  nwIpxAclDestNetNum STRING
  nwIpxAclDestNode STRING
  nwIpxAclDestSocket STRING
  nwIpxAclSrcNetNum STRING
  nwIpxAclSrcNode STRING
  nwIpxAclSrcSocket STRING

NwIpxNetBIOSIfEntry  
SEQUENCE    
  nwIpxNetBIOSIfIndex INTEGER
  nwIpxNetBIOSIfAdminStatus INTEGER
  nwIpxNetBIOSIfOperStatus INTEGER
  nwIpxNetBIOSIfOperationalTime TimeTicks

NwIpxNetBIOSIfCtrEntry  
SEQUENCE    
  nwIpxNetBIOSIfCtrIfIndex INTEGER
  nwIpxNetBIOSIfCtrAdminStatus INTEGER
  nwIpxNetBIOSIfCtrReset INTEGER
  nwIpxNetBIOSIfCtrOperationalTime TimeTicks
  nwIpxNetBIOSIfCtrInPkts Counter
  nwIpxNetBIOSIfCtrOutPkts Counter
  nwIpxNetBIOSIfCtrFilteredPkts Counter
  nwIpxNetBIOSIfCtrDiscardPkts Counter
  nwIpxNetBIOSIfCtrInBytes Counter
  nwIpxNetBIOSIfCtrOutBytes Counter
  nwIpxNetBIOSIfCtrFilteredBytes Counter
  nwIpxNetBIOSIfCtrDiscardBytes Counter

NwIpxBcastIfEntry  
SEQUENCE    
  nwIpxBcastIfIndex INTEGER
  nwIpxBcastIfAdminStatus INTEGER
  nwIpxBcastIfOperStatus INTEGER
  nwIpxBcastIfOperationalTime TimeTicks

NwIpxBcastIfCtrEntry  
SEQUENCE    
  nwIpxBcastIfCtrIfIndex INTEGER
  nwIpxBcastIfCtrAdminStatus INTEGER
  nwIpxBcastIfCtrReset INTEGER
  nwIpxBcastIfCtrOperationalTime TimeTicks
  nwIpxBcastIfCtrInPkts Counter
  nwIpxBcastIfCtrOutPkts Counter
  nwIpxBcastIfCtrFilteredPkts Counter
  nwIpxBcastIfCtrDiscardPkts Counter
  nwIpxBcastIfCtrInBytes Counter
  nwIpxBcastIfCtrOutBytes Counter
  nwIpxBcastIfCtrFilteredBytes Counter
  nwIpxBcastIfCtrDiscardBytes Counter

NwIpxEchoIfEntry  
SEQUENCE    
  nwIpxEchoIfIndex INTEGER
  nwIpxEchoIfAdminStatus INTEGER
  nwIpxEchoIfOperStatus INTEGER
  nwIpxEchoIfOperationalTime TimeTicks

NwIpxEchoIfCtrEntry  
SEQUENCE    
  nwIpxEchoIfCtrIfIndex INTEGER
  nwIpxEchoIfCtrAdminStatus INTEGER
  nwIpxEchoIfCtrReset INTEGER
  nwIpxEchoIfCtrOperationalTime TimeTicks
  nwIpxEchoIfCtrInPkts Counter
  nwIpxEchoIfCtrOutPkts Counter
  nwIpxEchoIfCtrFilteredPkts Counter
  nwIpxEchoIfCtrDiscardPkts Counter
  nwIpxEchoIfCtrInBytes Counter
  nwIpxEchoIfCtrOutBytes Counter
  nwIpxEchoIfCtrFilteredBytes Counter
  nwIpxEchoIfCtrDiscardBytes Counter

NwIpxHostMapEntry  
SEQUENCE    
  nwIpxHostMapIfIndex INTEGER
  nwIpxHostMapIpxAddr IpxAddress
  nwIpxHostMapPhysAddr PhysAddress
  nwIpxHostMapType INTEGER
  nwIpxHostMapCircuitID INTEGER
  nwIpxHostMapFraming INTEGER
  nwIpxHostMapPortNumber INTEGER

NwIpxEventFilterEntry  
SEQUENCE    
  nwIpxEventFltrProtocol INTEGER
  nwIpxEventFltrIfNum INTEGER
  nwIpxEventFltrControl INTEGER
  nwIpxEventFltrType INTEGER
  nwIpxEventFltrSeverity INTEGER
  nwIpxEventFltrAction INTEGER

NwIpxEventEntry  
SEQUENCE    
  nwIpxEventNumber INTEGER
  nwIpxEventTime TimeTicks
  nwIpxEventType INTEGER
  nwIpxEventSeverity INTEGER
  nwIpxEventProtocol INTEGER
  nwIpxEventIfNum INTEGER
  nwIpxEventTextString STRING

Defined Values

nwIpxRouter 1.3.6.1.4.1.52.4.2.2.2.3.2
OBJECT IDENTIFIER    

nwIpxMibs 1.3.6.1.4.1.52.4.2.2.2.3.2.1
OBJECT IDENTIFIER    

nwIpxComponents 1.3.6.1.4.1.52.4.2.2.2.3.2.2
OBJECT IDENTIFIER    

nwIpxSystem 1.3.6.1.4.1.52.4.2.2.2.3.2.2.1
OBJECT IDENTIFIER    

nwIpxForwarding 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2
OBJECT IDENTIFIER    

nwIpxTopology 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4
OBJECT IDENTIFIER    

nwIpxFib 1.3.6.1.4.1.52.4.2.2.2.3.2.2.5
OBJECT IDENTIFIER    

nwIpxEndSystems 1.3.6.1.4.1.52.4.2.2.2.3.2.2.6
OBJECT IDENTIFIER    

nwIpxAccessControl 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7
OBJECT IDENTIFIER    

nwIpxFilters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.8
OBJECT IDENTIFIER    

nwIpxRedirector 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9
OBJECT IDENTIFIER    

nwIpxEvent 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10
OBJECT IDENTIFIER    

nwIpxWorkGroup 1.3.6.1.4.1.52.4.2.2.2.3.2.2.11
OBJECT IDENTIFIER    

nwIpxSysConfig 1.3.6.1.4.1.52.4.2.2.2.3.2.2.1.1
OBJECT IDENTIFIER    

nwIpxSysAdministration 1.3.6.1.4.1.52.4.2.2.2.3.2.2.1.2
OBJECT IDENTIFIER    

nwIpxFwdSystem 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1
OBJECT IDENTIFIER    

nwIpxFwdInterfaces 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2
OBJECT IDENTIFIER    

nwIpxFwdCounters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1
OBJECT IDENTIFIER    

nwIpxFwdIfConfig 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1
OBJECT IDENTIFIER    

nwIpxFwdIfCounters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2
OBJECT IDENTIFIER    

nwIpxDistanceVector 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1
OBJECT IDENTIFIER    

nwIpxLinkState 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.2
OBJECT IDENTIFIER    

nwIpxRip 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1
OBJECT IDENTIFIER    

nwIpxSap 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2
OBJECT IDENTIFIER    

nwIpxRipSystem 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1
OBJECT IDENTIFIER    

nwIpxRipInterfaces 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2
OBJECT IDENTIFIER    

nwIpxRipDatabase 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.3
OBJECT IDENTIFIER    

nwIpxRipFilters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.4
OBJECT IDENTIFIER    

nwIpxRipConfig 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.1
OBJECT IDENTIFIER    

nwIpxRipCounters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.2
OBJECT IDENTIFIER    

nwIpxRipIfConfig 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1
OBJECT IDENTIFIER    

nwIpxRipIfCounters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2
OBJECT IDENTIFIER    

nwIpxSapSystem 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1
OBJECT IDENTIFIER    

nwIpxSapInterfaces 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2
OBJECT IDENTIFIER    

nwIpxSapServerTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3
OBJECT IDENTIFIER    

nwIpxSapFilters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.4
OBJECT IDENTIFIER    

nwIpxSapConfig 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.1
OBJECT IDENTIFIER    

nwIpxSapCounters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.2
OBJECT IDENTIFIER    

nwIpxSapIfConfig 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1
OBJECT IDENTIFIER    

nwIpxSapIfCounters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2
OBJECT IDENTIFIER    

nwIpxNlsp 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.2.1
OBJECT IDENTIFIER    

nwIpxHostsSystem 1.3.6.1.4.1.52.4.2.2.2.3.2.2.6.1
OBJECT IDENTIFIER    

nwIpxHostsInterfaces 1.3.6.1.4.1.52.4.2.2.2.3.2.2.6.2
OBJECT IDENTIFIER    

nwIpxHostsToMedia 1.3.6.1.4.1.52.4.2.2.2.3.2.2.6.3
OBJECT IDENTIFIER    

nwIpxNetBIOS 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1
OBJECT IDENTIFIER    

nwIpxBroadcast 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2
OBJECT IDENTIFIER    

nwIpxEcho 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3
OBJECT IDENTIFIER    

nwIpxNetBIOSSystem 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1
OBJECT IDENTIFIER    

nwIpxNetBIOSInterface 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2
OBJECT IDENTIFIER    

nwIpxNetBIOSConfig 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.1
OBJECT IDENTIFIER    

nwIpxNetBIOSCounters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.2
OBJECT IDENTIFIER    

nwIpxNetBIOSIfConfig 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.1
OBJECT IDENTIFIER    

nwIpxNetBIOSIfCounters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2
OBJECT IDENTIFIER    

nwIpxBroadcastSystem 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1
OBJECT IDENTIFIER    

nwIpxBroadcastInterface 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2
OBJECT IDENTIFIER    

nwIpxBroadcastConfig 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.1
OBJECT IDENTIFIER    

nwIpxBroadcastCounters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.2
OBJECT IDENTIFIER    

nwIpxBroadcastIfConfig 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.1
OBJECT IDENTIFIER    

nwIpxBroadcastIfCounters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2
OBJECT IDENTIFIER    

nwIpxEchoSystem 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1
OBJECT IDENTIFIER    

nwIpxEchoInterface 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2
OBJECT IDENTIFIER    

nwIpxEchoConfig 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.1
OBJECT IDENTIFIER    

nwIpxEchoCounters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.2
OBJECT IDENTIFIER    

nwIpxEchoIfConfig 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.1
OBJECT IDENTIFIER    

nwIpxEchoIfCounters 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2
OBJECT IDENTIFIER    

nwIpxEventLogConfig 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.1
OBJECT IDENTIFIER    

nwIpxEventLogFilterTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.2
OBJECT IDENTIFIER    

nwIpxEventLogTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.3
OBJECT IDENTIFIER    

nwIpxMibRevText 1.3.6.1.4.1.52.4.2.2.2.3.2.1.1
Indicates the current revision level of the IPX MIB in textual format.
OBJECT-TYPE    
  DisplayString  

nwIpxSysRouterId 1.3.6.1.4.1.52.4.2.2.2.3.2.2.1.1.1
The IPX Address used to uniquely identify the host (device) running IPX Routing Services. The value of nwIpxSysRouterId is equal to the highest IPX address assigned in the IPX Address Table.
OBJECT-TYPE    
  IpxAddress  

nwIpxSysAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.1.2.1
Sets the administrative state of IPX Routing Services system-wide. Enabled (3) causes IPX Routing Services to become active on all router ports configured and enabled for IPX Routing Services. Disabled (2) causes IPX routing services to become inactive system-wide.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxSysOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.1.2.2
Indicates the operating condition of IPX Routing Services system-wide. The value of nwIpxSysOperStatus indicates any problem with your IPX Routing Services configuration. A value of 6 indicates that regardless of the value of nwIpxSysAdminStatus, IPX Routing Services is not operating because of an invalid configuration.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5), invalid-config(6)  

nwIpxSysAdminReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.1.2.3
Resets IPX Routing Services system-wide. Reset (2) forces a restart of IPX Routing Services without a graceful shutdown on any active router ports and without affecting any other routing services.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxSysOperationalTimel 1.3.6.1.4.1.52.4.2.2.2.3.2.2.1.2.4
Indicates the elapsed time, in hundredths of a second, that nwIpxSysOperStatus has been in its current administrative state.
OBJECT-TYPE    
  TimeTicks  

nwIpxSysVersion 1.3.6.1.4.1.52.4.2.2.2.3.2.2.1.2.5
Indicates the current revision level of the IPX Routing Services firmware in textual format.
OBJECT-TYPE    
  DisplayString  

nwIpxFwdCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.1
Sets the administrative state of the aggregate (system-wide) IPX packet and byte counters. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxFwdCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.2
Resets the aggregate (system-wide) IPX packet and byte counters. Reset (2) resets the IPX aggregate counters to 0. nwIpxFwdCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxFwdCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.3
Indicates the elapsed time, in hundredths of a second, that nwIpxFwdCtrAdminStatus has been in the current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxFwdCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.4
Indicates the total number of IPX packets that have been received, system-wide, during nwIpxFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.5
Indicates the total number of IPX packets that have been transmitted, system-wide, during nwIpxFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrFwdPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.6
Indicates the total number of IPX packets that have been forwarded, system-wide, during nwIpxFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.7
Indicates the total number of IPX packets that have been administratively filtered, system-wide, during nwIpxFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.8
Indicates the total number of IPX packets that have been discarded, system-wide, during nwIpxFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrAddrErrPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.9
Indicates the total number of IPX packets that have been discarded, system-wide, during nwIpxFwdCtrOperationalTime, because of addressing errors in the IPX header.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrLenErrPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.10
Indicates the total number of IPX packets that have been discarded, system-wide, during nwIpxFwdCtrOperationalTime, because an invalid packet length is contained in the IPX header.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrHdrErrPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.11
Indicates the total number of IPX packets that have been discarded, system-wide, during nwIpxFwdCtrOperationalTime, because of an invalid IPX header.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.12
Indicates the total number of bytes in the IPX packets that have been received, system-wide, during nwIpxFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.13
Indicates the total number of bytes in the IPX packets that have been transmitted, system-wide, during nwIpxFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrFwdBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.14
Indicates the total number of bytes in the IPX packets that have been forwarded, system-wide, during nwIpxFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.15
Indicates the total number of bytes in the IPX packets that have been administratively filtered, system-wide, during nwIpxFwd-CtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.16
Indicates the total number of bytes in the IPX packets that have been discarded, system-wide during nwIpxFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrHostInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.17
Indicates the total number of IPX packets that have been successfully delivered to the local host, during nwIpxFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrHostOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.18
Indicates the total number of IPX packets that have been transmitted by the local host, during nwIpxFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrHostDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.19
Indicates the total number of IPX packets that have been discarded by the local host, during nwIpxFwdCtrOperationalTime, due to a lack of host resources.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrHostInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.20
Indicates the total number of bytes in the IPX packets that have been received by the local host, during nwIpxFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrHostOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.21
Indicates the total number of bytes in the IPX packets that have been transmitted by the local host, during nwIpxFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxFwdCtrHostDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.1.1.22
Indicates the total number of bytes in the IPX packets that have been discarded by the local host, during nwIpxFwdCtrOperationalTime due to a lack of host resources.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1
This table contains an entry for each router port. This table is indexed by nwIpxFwdIfIndex, which indicates the value of MIB2 ifIndex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxFwdIfEntry

nwIpxFwdIfEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1
Each entry specifies the IPX Routing Services configuration for the router port for which the entry exists.
OBJECT-TYPE    
  NwIpxFwdIfEntry  

nwIpxFwdIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.1
Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxFwdIfAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.2
Sets the administrative state of IPX Routing Services on the router port for which the entry exists. Enabled (3) causes IPX Routing Services to become active. Disabled (2) causes it to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxFwdIfOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.3
Indicates the current operating condition of IPX Routing Services on the router port for which the entry exists. The value of nwIpxFwdIfOperStatus indicates any problem with the configuration of IPX Routing Services on the router port. A value of 6 indicates that regardless of the state of nwIpxFwdIfAdminStatus IPX Routing Services is not operating because of an invalid port-level configuration.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5), invalid-config(6)  

nwIpxFwdIfOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwIpxFwdIfOperStatus has been in its current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxFwdIfControl 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.5
This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER other(1), add(2), delete(3)  

nwIpxFwdIfMtu 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.6
Specifies the Maximum Transmission Unit (MTU) for IPX packets on the router port for which the entry exists. This includes the IPX header and data but does not include framing.
OBJECT-TYPE    
  INTEGER  

nwIpxFwdIfForwarding 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.7
Controls forwarding of IPX packets on the router port for which the entry exists. Enabled (3) causes IPX packets to be forwarded. Disabled (2) prevents IPX packets from being forwarded.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxFwdIfFrameType 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.8
Specifies the framing type for IPX packets forwarded on the router port for which the entry exists. Some frame types are valid for specific media types. The comments reflect those valid media types.
OBJECT-TYPE    
  INTEGER other(1), ethernet(2), snap(3), i8022(4), novell(6), nativewan(8), encapenet(9), encapenet8022(10), encapenetsnap(11), encapenetnovell(12), encaptr8022(13), encaptrsnap(14), encapfddi8022(15), encapfddisnap(16), canonical(17)  

nwIpxFwdIfAclIdentifier 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.9
Specifies the Access Control ID of the Access Control List in effect for IPX packets being routed on the router port for which the entry exists. A value of 0 indicates that no Access Control List is in effect.
OBJECT-TYPE    
  INTEGER  

nwIpxFwdIfAclStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.10
Controls the operation of any Access Control List configured for IPX traffic on the router port for which the entry exists. Enabled (3) applies the Access Control List indicated by the value of nwIpxFwdIfAclIdentifier to all IPX traffic being routed to the port. Disabled (2) prevents the Access Control List from being applied.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxFwdIfCacheControl 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.11
Controls IPX Address caching on the router port for which the entry exists. When IPX Address caching is enabled, IPX Addresses used for address validation, filtering, and forwarding are stored in the cache. This cache is checked first before doing a full route table lookup, which speeds up the switching process. Enabled (3) turns on IPX Address caching. Disabled (2) turns it off.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

nwIpxFwdIfCacheEntries 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.12
Indicates the number of entries in the IPX Address cache on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCacheHits 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.13
Indicates the number of times entries in the IPX Adddress cache have been used to provide the IPX Address required to validate, filter, or forward an IPX packet on the router port.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCacheMisses 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.1.1.14
Indicates the number of times the IPX Address required to validate, filter, or forward an IPX packet on the router port was not found in the IPX Address cache.
OBJECT-TYPE    
  Counter  

nwIpxAddressTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.2
This table contains an entry for each Novell network address assigned to each router port.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxAddrEntry

nwIpxAddrEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.2.1
Each entry specifies the Novell network addressing information for the logical Novll network for which the entry exists.
OBJECT-TYPE    
  NwIpxAddrEntry  

nwIpxAddrIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.2.1.1
Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxAddrIfAddress 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.2.1.2
This is the Novell network number assigned to the logical Novell network for which the entry exists. The IpxAddress consists of a network number of 4 octets.
OBJECT-TYPE    
  IpxAddress  

nwIpxAddrIfControl 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.2.1.3
Set this object to add or delete this entry from the table.
OBJECT-TYPE    
  INTEGER other(1), add(2), delete(3)  

nwIpxAddrIfAddrType 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.1.2.1.4
Specifies whether the Novell network number, nwIpxAddrIfAddress, is the primary or secondary address for the router port.
OBJECT-TYPE    
  INTEGER other(1), primary(2), secondary(3)  

nwIpxFwdIfCtrTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1
This table contains an entry for each router port configured and enabled for IPX Routing Services.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxFwdIfCtrEntry

nwIpxFwdIfCtrEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1
Each entry indicates the current packet and byte count of IPX packets on the port for which the entry exists.
OBJECT-TYPE    
  NwIpxFwdIfCtrEntry  

nwIpxFwdIfCtrIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.1
Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxFwdIfCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.2
Sets the administrative state of the per-port IPX packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxFwdIfCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.3
Resets the per-port IPX packet and byte counters on the router port for which this entry exists. Reset (2) resets the counters to 0. nwIpxFwdIfCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxFwdIfCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwIpxFwdIfCtrAdminStatus has been in the current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxFwdIfCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.5
Indicates the total number of IPX packets that have been received, during nwIpxFwdIfCtrOperationaltime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.6
Indicates the total number of IPX packets that have been transmitted, during nwIpxFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrFwdPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.7
Indicates the total number of IPX packets that have been forwarded, during nwIpxFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.8
Indicates the total number of IPX packets that have been administratively filtered, during nwIpxFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.9
Indicates the total number of IPX packets that have been discarded (dropped), during nwIpxFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrAddrErrPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.10
Indicates the total number of IPX packets that have been discarded because of IPX addressing errors in the IPX header, during nwIpxFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrLenErrPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.11
Indicates the total number of IPX packets that have been discarded because an invalid packet length was contained in the IPX header, during nwIpxFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrHdrErrPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.12
Indicates the total number of IPX packets that have been discarded because of an invalid IPX header, during nwIpxFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.13
Indicates the total number of bytes in the IPX packets that have been received, during nwIpxFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.14
Indicates the total number of bytes in the IPX packets that have been transmitted, during nwIpxFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrFwdBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.15
Indicates the total number of bytes in the IPX packets that have been forwarded, during nwIpxFwdCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.16
Indicates the total number of bytes in the IPX packets administratively filtered, during nwIpxFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.17
Indicates the total number of bytes in the IPX packets that have been discarded, during nwIpxFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrHostInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.18
Indicates the total number of IPX packets that have been successfully delivered to the local host, during nwIpxFwdIfCtrOperationalTime, that were received on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrHostOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.19
Indicates the total number of IPX packets that have been forwarded by the local host, during nwIpxFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrHostDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.20
Indicates the total number of IPX packets that have been discarded by the local host, due to a lack of host resources, during nwIpxFwdIfCtrOperationalTime, that were received on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrHostInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.21
Indicates the total number of bytes in the IPX packets that have been successfully delivered to the local host, during nwIpxFwdIfCtrOperationalTime, that were received on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrHostOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.22
Indicates the total number of bytes in the IPX packets that have been transmitted by the local host, during nwIpxFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxFwdIfCtrHostDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.2.2.2.1.1.23
Indicates the total number of bytes in the IPX packets that have been discarded by the local host, due to a lack of host resources that were received, during nwIpxFwdIfCtrOperationalTime, that were received on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxRipAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.1.1
Sets the administrative state of the IPX-RIP routing protocol system-wide. Enabled (3) causes IPX-RIP to become active on all router ports configured and enabled for IPX Routing Services. Disabled (2) causes IPX-RIP to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxRipOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.1.2
Indicates the current operating condition of IPX-RIP system-wide. The value of nwIpxRipOperStatus indicates any problem with your IPX-RIP configuration. A value of 6 indicates that regardless of the value of nwIpxRipAdminStatus, IPX-RIP is not operating because of an invalid configuration.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5)  

nwIpxRipAdminReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.1.3
Resets the IPX-RIP routing protocol. Reset (2) forces a system-wide restart of IPX-RIP, without a graceful shutdown on any active router ports.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxRipOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwIpxRipOperStatus has been in its current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxRipVersion 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.1.5
Indicates the current revision level of the IPX-RIP routing protocol firmware, in textual format.
OBJECT-TYPE    
  DisplayString  

nwIpxRipStackSize 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.1.6
Specifies the stack size of the IPX-RIP routing protocol thread. In order for a change of this value to take effect, the protocol (nwIpxRipAdminReset), IPX Routing Services (nwIpxSysAdminReset), or the device running Routing Services must be reset.
OBJECT-TYPE    
  INTEGER  

nwIpxRipThreadPriority 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.1.7
Specifies the run-time execution priority of the IPX-RIP routing protocol thread. In order for a change of this value to take effect, IPX-RIP (nwIpxRipAdminReset), IPX Routing Services (nwIpxAdminReset), or the device running Routing services must be reset.
OBJECT-TYPE    
  INTEGER  

nwIpxRipDatabaseThreshold 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.1.8
Specifies the run-time maximum number of IPX-RIP entries that can be held in the IPX-RIP route table.
OBJECT-TYPE    
  INTEGER  

nwIpxRipAgeOut 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.1.9
Specifies the amount of time, in seconds, that an inactive route table entry remains in the IPX-RIP route table before it is aged-out.
OBJECT-TYPE    
  INTEGER  

nwIpxRipHoldDown 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.1.10
Specifies the amount of time, in seconds, to wait before removing an entry from the route table, after receiving an update indicating that the destination has become unreachable. All routers exchanging IPX-RIP information must have the same hold down time. The time must be long enough to allow all participating routers to receive the same update.
OBJECT-TYPE    
  INTEGER  

nwIpxRipCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.2.1
Sets the administrative state of the aggregate system-wide IPX-RIP packet and byte counters. Enabled (3) causes these counters to become active on all router ports. Disabled (2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxRipCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.2.2
Resets the aggregate system-wide IPX-RIP protocol packet and byte counters. Reset (2) resets the IPX-RIP aggregate counters to 0. nwIpxRipCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxRipCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.2.3
Indicates the elapsed time, in hundredths of a second, that nwIpxRipCtrAdminStatus has been in the current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxRipCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.2.4
Indicates the total number of IPX-RIP packets that have been received, system-wide, during nwIpxRipCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxRipCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.2.5
Indicates the total number of IPX-RIP packets that have been transmitted, system-wide, during nwIpxRipCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxRipCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.2.6
Indicates the total number of IPX-RIP packets that have been administratively filtered, system-wide, during` nwIpxRipCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxRipCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.2.7
Indicates the total number of IPX-RIP packets that have been discarded, system-wide, during nwIpxRipCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxRipCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.2.8
Indicates the total number of bytes in the IPX-RIP packets that have been received, system-wide, during nwIpxRipCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxRipCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.2.9
Indicates the total number of bytes in the IPX-RIP packets that have been transmitted, system-wide, during nwIpxRipCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxRipCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.2.10
Indicates the total number of bytes in the IPX-RIP packets that have been administratively filtered, system-wide, during nwIpxRipCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxRipCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.1.2.11
Indicates the total number of bytes in the IPX-RIP packets that have been discarded, during nwIpxRipCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxRipIfTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1
This table contains an entry for each router port. Each entry can contain different values, allowing the routing protocol configuration to vary from router port to router port. This table is indexed by nwIpxRipIfIndex, which indicates the value of MIB 2 ifindex, which identifies the router port for which each entry exists.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxRipIfEntry

nwIpxRipIfEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1
Each entry contains the IPX-RIP configuration for the router port for which the entry exists.
OBJECT-TYPE    
  NwIpxRipIfEntry  

nwIpxRipIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.1
Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxRipIfAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.2
Sets the administrative state of the IPX-RIP routing protocol on the router port for which the entry exists. Enabled (3) causes IPX-RIP to become active on the router port. Disabled (2) causes RIP to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxRipIfOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.3
Indicates the current operating condition of the IPX-RIP routing protocol on the router port for which the entry exists. The value of nwIpxRipIfOperStatus indicates any problem with your IPX-RIP configuration on the router port. A value of 6 indicates that regardless of the value of nwIpxRipIfAdminStatus, IPX-RIP is not operating on the router port because of an invalid configuration.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5)  

nwIpxRipIfOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwIpxRipIfOperStatus has been in its current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxRipIfVersion 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.5
Indicates the revision level of the IPX-RIP routing protocol in textual format.
OBJECT-TYPE    
  INTEGER  

nwIpxRipIfAdvertisement 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.6
Sets the interval, in seconds, at which IPX-RIP advertises its route table on the router port for which the entry exists. Change this value to cause IPX-RIP to advertise its route table more or less frequently.
OBJECT-TYPE    
  INTEGER  

nwIpxRipIfFloodDelay 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.7
Specifies the length of time, in seconds, that the IPX-RIP routing protocol will wait after discovering that a directly connected route has gone down, before flooding updates (triggered updates) on the router port for which the entry exists. A value of 0 specifies that if a directly connected route goes down, updates will be sent immediately.
OBJECT-TYPE    
  INTEGER  

nwIpxRipIfRequestDelay 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.8
Specifies the length of time, in seconds, that the IPX-RIP routing protocol will wait after receiving a route request packet before sending a response on the router port for which the entry exists. A value of 0 specifies that if a route request packet is received on the port, a response will be sent immediately.
OBJECT-TYPE    
  INTEGER  

nwIpxRipIfPriority 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.9
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER  

nwIpxRipIfHelloTimer 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.10
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER  

nwIpxRipIfSplitHorizon 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.11
Controls the operation of Split Horizon on the router port for which the entry exists. When Split Horizon is enabled, IPX-RIP keeps track of which router port route information is received on, and prevents information about a route from being sent back out the same router port it was received on.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxRipIfPoisonReverse 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.12
Controls the operation of Poison Reverse on the router port for which the entry exists. When Poison Reverse is enabled, IPX-RIP advertises any downed route as unreachable during the period of time that it must wait (nwIpxRipHoldDown) before removing the route from the route table.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxRipIfSnooping 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.13
Controls the operation of IPX-RIP Snooping on the router port. When RIP Snooping is enabled the IPX-RIP routing protocol operates in passive mode, so that it receives route information, builds and maintains a route table, but does not advertise or send updates on the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxRipIfType 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.14
Indicates whether the directly connected network segment does or does not support broadcast media access. If broadcast media access is supported, IPX-RIP advertisements are sent out one broadcast packet per router port. If broadcast media access is not supported, IPX-RIP advertisements are sent to each neighbor directly.
OBJECT-TYPE    
  INTEGER other(1), bma(2), nbma(3)  

nwIpxRipIfXmitCost 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.15
This object does not apply to this protocol. It is a common object, inherited from the common MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER  

nwIpxRipIfAclIdentifier 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.16
Specifies the Access Control ID of the access control list in effect for IPX-RIP routing protocol packets on the router port for which the entry exists. A value of 0 indicates that there is no access control list in effect for IPX-RIP routing protocol packets on the router port.
OBJECT-TYPE    
  INTEGER  

nwIpxRipIfAclStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.1.1.1.17
Controls the operation of the access control list identified by nwIpxRipIfAclIdentifier. Enabled (3) applies the access control list to all IPX-RIP routing protocol packet traffic on the router port for which the entry exists. Disabled (2) prevents the access control list from being applied.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxRipIfCtrTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1
This table contains an entry for each router port.This table is indexed by nwIpxRipIfCtrIfIndex, which indicates the value of MIB2 ifindex, which indentifies the router port for which the entry exists.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxRipIfCtrEntry

nwIpxRipIfCtrEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1.1
Each entry indicates the current packet and byte count of IPX-RIP routing protocol packets on the router port for which the entry exists.
OBJECT-TYPE    
  NwIpxRipIfCtrEntry  

nwIpxRipIfCtrIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1.1.1
Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxRipIfCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1.1.2
Sets the administrative state of the per-port IPX-RIP packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxRipIfCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1.1.3
Resets the per-port IPX-RIP packet and byte counters on the router port for which this entry exists. Reset (2) resets the counters to 0. nwIpxRipIfCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxRipIfCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwIpRipIfCtrAdminStatus has been in the current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxRipIfCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1.1.5
Indicates the total number of IPX-RIP routing protocol packets that have been received, during nwIpxRipIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxRipIfCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1.1.6
Indicates the total number of IPX-RIP routing protocol packets that have been transmitted, during nwIpxRipIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxRipIfCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1.1.7
Indicates the total number of IPX-RIP routing protocol packets that have been administratively filtered, during nwIpxRipIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxRipIfCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1.1.8
Indicates the total number of IPX-RIP routing protocol packets that have been discarded, during nwIpxRipIfCtrOperationalTime, that were received on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxRipIfCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1.1.9
Indicates the total number of bytes in the IPX-RIP routing protocol packets that have been received, during nwIpxRipIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxRipIfCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1.1.10
Indicates the total number of bytes in the IPX-RIP routing protocol packets that have been transmitted, during nwIpxRipIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxRipIfCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1.1.11
Indicates the total number of bytes in the IPX-RIP routing protocol packets that have been administratively filtered, during nwIpxRipIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxRipIfCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.2.2.1.1.12
Indicates the total number of bytes in the IPX-RIP routing protocol packets that have been discarded, during nwIpRipIfCtrOperationalTime, that were received on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxRipRouteTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.3.1
This table contains the IPX-RIP route table. This table contains an entry for each route learned through the IPX-RIP routing protocol. Only the best routes from this table are added to the IPX forwarding table to be used for packet switching.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxRipRouteEntry

nwIpxRipRouteEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.3.1.1
Each entry describes the IPX-RIP route to the destination network for which the entry exists.
OBJECT-TYPE    
  NwIpxRipRouteEntry  

nwIpxRipRtNetId 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.3.1.1.1
This is the primary index into the IPX-RIP route table. This number indicates the Novell Network Number of the destination for which the entry exists. The IpxAddress consists of a network number of 4 octets
OBJECT-TYPE    
  IpxAddress  

nwIpxRipRtIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.3.1.1.2
This is a secondary index into the IPX-RIP route table. This number corresponds to the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxRipRtSrcNode 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.3.1.1.3
This is a secondary index into the RIP route table. This number indicates the MAC-layer address of the source router from which this route was learned. A value of 0.0.0.0.0.0 indicates that the source is on the network segment directly connected to the router port, nwIpxRipRtIfIndex.
OBJECT-TYPE    
  IpxAddress  

nwIpxRipRtHops 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.3.1.1.4
Indicates the number of hops required to reach the destination for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxRipRtTicks 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.3.1.1.5
Indicates the amount of time (number of Time Ticks) required to reach the destination for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxRipRtAge 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.3.1.1.6
Indicates the amount of time, in seconds, since an update has been received for the route for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxRipRtType 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.3.1.1.7
Indicates whether the destination network is directly connected through the router port specified by nwIpxRipRtIndex, or is indirectly connected through another router, specified by nwIpxRipRtSrcNode.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), direct(3), remote(4)  

nwIpxRipRtFlags 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.1.3.1.1.8
Specifies properties of the IPX-RIP route. The bit mask is as follows: source-changed (1), best source (2), local-net (4), net-down (8), update-fib-only (16).
OBJECT-TYPE    
  INTEGER  

nwIpxSapAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.1.1
Sets the administrative state of the SAP protocol system-wide. Enabled (3) causes SAP to become active on all router ports configured and enabled for IPX routing services. Disabled (2) causes the protocol to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxSapOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.1.2
Indicates the current operating condition of the SAP protocol system-wide. The value of nwIpxSapOperStatus indicates any problem with your SAP configuration. A value of 6 indicates that regardless of the value of nwIpxSAPAdminStatus, the SAP protocol is not operating because of an invalid configuration.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5)  

nwIpxSapAdminReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.1.3
Resets the SAP protocol. Reset (2) forces a system-wide restart of SAP, without a graceful shutdown on any active router ports.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxSapOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwIpxSapOperStatus, has been in its current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxSapVersion 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.1.5
Indicates the current revision level of the SAP protocol firmware, in textual format.
OBJECT-TYPE    
  DisplayString  

nwIpxSapStackSize 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.1.6
Specifies the stack size of the SAP protocol thread. In order for a change to this value to take effect, the protocol (nwIpxSapAdminReset), IPX Routing Services (nwIpxSysAdminReset), or the device running Routing Services must be reset.
OBJECT-TYPE    
  INTEGER  

nwIpxSapThreadPriority 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.1.7
Specifies the run-time execution priority of the SAP protocol thread. In order for a change to this value to take effect, SAP (nwIpxSapAdminReset), IPX Routing Services (nwIpxAdminReset), or the device running Routing Services must be reset.
OBJECT-TYPE    
  INTEGER  

nwIpxSapDatabaseThreshold 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.1.8
Specifies the run-time maximum number of entries that can be held in the SAP server table.
OBJECT-TYPE    
  INTEGER  

nwIpxSapAgeOut 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.1.9
Specifies the amount of time, in seconds, that an inactive server table entry remains in the SAP server table before it is aged out.
OBJECT-TYPE    
  INTEGER  

nwIpxSapHoldDown 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.1.10
Specifies the amount of time, in seconds, to wait before removing an entry from the SAP server table, after receiving an update indicating that the destination has become unreachable. All routers exchanging SAP information must have the same hold down time. The time must be long enough to allow all participating routers to receive the same update.
OBJECT-TYPE    
  INTEGER  

nwIpxSapCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.2.1
Sets the administrative state of the aggregate (system-wide) SAP protocol packet and byte counters. Enabled (3) causes these counters to become active on all router ports. Disabled (2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxSapCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.2.2
Resets the aggregate (system-wide) SAP protocol packet and byte counters. Reset (2) resets the SAP aggregate counters to 0. nwIpxSapCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxSapCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.2.3
Indicates the elapsed time, in hundredths of a second, that nwIpxSapCtrAdminStatus, has been in the current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxSapCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.2.4
Indicates the total number of SAP packets that have been received, system-wide, during nwIpxSapCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxSapCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.2.5
Indicates the total number of SAP packets that have been transmitted, system-wide, during nwIpxSapCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxSapCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.2.6
Indicates the total number of SAP packets that have been administratively filtered, system-wide, during nwIpxSapCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxSapCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.2.7
Indicates the total number of SAP packets that have been discarded, system-wide, during nwIpxSapCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxSapCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.2.8
Indicates the total number of bytes in the SAP packets that have been received, system-wide, during nwIpxSapCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxSapCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.2.9
Indicates the total number of bytes in the SAP packets that have been transmitted, system-wide, during nwIpxSapCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxSapCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.2.10
Indicates the total number of bytes in the SAP packets that have been administratively filtered, system-wide, during nwIpxSapCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxSapCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.1.2.11
Indicates the total number of bytes in the SAP packets that have been discarded system-wide, during nwIpxSapCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxSapIfTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1
This table contains an entry for each router port. Each entry can contain different values, allowing the SAP configuration to vary from router port to router port. This table is indexed by nwIpxSapIfIndex, which indicates the value of MIB 2 ifindex, which identifies the router port for which each entry exists.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxSapIfEntry

nwIpxSapIfEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1
Each entry contains the SAP configuration for the router port for which the entry exists.
OBJECT-TYPE    
  NwIpxSapIfEntry  

nwIpxSapIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.1
Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxSapIfAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.2
Sets the administrative state of the SAP protocol on the router port for which the entry exists. Enabled (3) causes SAP to become active on the router port. Disabled (2) causes SAP to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxSapIfOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.3
Indicates the current operating condition of the SAP protocol on the router port for which the entry exists. The value of nwIpxSapIfOperStatus indicates any problem with your SAP configuration on the router port. A value of 6 indicates that regardless of the value of nwIpxSapIfAdminStatus. SAP is not operating because of an invalid configuration.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5)  

nwIpxSapIfOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwIpxSapIfOperStatus has been in its current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxSapIfVersion 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.5
Indicates the revision level of the SAP protocol in textual format.
OBJECT-TYPE    
  INTEGER  

nwIpxSapIfAdvertisement 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.6
Sets the interval, in seconds, at which SAP advertises its server table on the router port for which the entry exists. Change this value to cause SAP to advertise its server table more or less frequently.
OBJECT-TYPE    
  INTEGER  

nwIpxSapIfFloodDelay 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.7
Specifies the length of time, in seconds, that the SAP protocol will wait after discovering that a directly connected route has gone down, before flooding updates (triggered updates) on the router port for which the entry exists. A value of 0 specifies that if a directly connected route goes down, updates should be sent immediately .
OBJECT-TYPE    
  INTEGER  

nwIpxSapIfRequestDelay 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.8
Specifies the length of time, in seconds, that the SAP protocol will wait after receiving a server request packet, before sending a response on the router port for which the entry exists. A value of 0 specifies that if a server request packet is received on the port, a response will be sent immediately.
OBJECT-TYPE    
  INTEGER  

nwIpxSapIfPriority 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.9
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER  

nwIpxSapIfHelloTimer 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.10
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a management interface to all the Cabletron Routing Services protocol-specific MIBs.Setting this object has no effect.
OBJECT-TYPE    
  INTEGER  

nwIpxSapIfSplitHorizon 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.11
Controls the operation of Split Horizon on the router port for which the entry exists. When Split Horizon is enabled, SAP keeps track of which router port information is received on, and prevents information about a server from being sent back out the same router port it was received on.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxSapIfPoisonReverse 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.12
Controls the operation of Poison Reverse on the router port for which the entry exists. When Poison Reverse is enabled, SAP advertises any downed server as unreachable during the period of time that it must wait (nwIpxSapIfHoldDown) before removing the server from the server table.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxSapIfSnooping 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.13
Controls the operation of SAP Snooping on the router port. When SAP Snooping is enabled SAP operates in passive mode, so it receives service information, builds and maintains a server table, but does not advertise or send updates on the router port for which the entry exists. Enabled (3) turns on SAP Snooping. Disabled (2) turns off SAP Snooping.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxSapIfType 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.14
Indicates whether the directly connected network segment does or does not support broadcast media access. If broadcast media access is supported, SAP advertisements are sent out, one broadcast packet per router port. If broadcast media access is not supported, SAP advertisements are sent to each neighbor router directly.
OBJECT-TYPE    
  INTEGER other(1), bma(2), nbma(3)  

nwIpxSapIfXmitCost 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.15
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER  

nwIpxSapIfAclIdentifier 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.16
Specifies the Access Control List ID of the access control list in effect for SAP protocol packets on the router port for which the entry exists. A value of 0 indicates that there is no access control list in effect for SAP protocol packets on the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxSapIfAclStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.1.1.1.17
Controls the operation of the access control list identified by nwIpxSapIfAclIdentifier. Enabled (3) causes the access control list to be applied to all SAP protocol packet traffic on the router port for which the entry exists. Disabled (2) prevents the access control list from being applied.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxSapIfCtrTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1
This table contains an entry for each router port. This table is indexed by nwIpxSapIfCtrIfIndex which indicates the value of MIB2 ifindex, which indentifies the router port for which the entry exists.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxSapIfCtrEntry

nwIpxSapIfCtrEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1.1
Each entry indicates the current packet and byte count of SAP protocol packets on the router port for which the entry exists.
OBJECT-TYPE    
  NwIpxSapIfCtrEntry  

nwIpxSapIfCtrIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1.1.1
Indicates the value of the MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxSapIfCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1.1.2
Sets the administrative state of the per-port SAP packet and byte counters on the router port for which this entry exists. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxSapIfCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1.1.3
Resets the per-port SAP packet and byte counters on the router port for which the entry exists. Reset (2) resets the counters to 0. nwIpxSapIfCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxSapIfCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwIpxSapIfCtrAdminStatus has been in the current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxSapIfCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1.1.5
Indicates the total number of SAP protocol packets that have been received, during nwIpxSapIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxSapIfCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1.1.6
Indicates the total number of SAP packets that have been transmitted, during nwIpxSapIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxSapIfCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1.1.7
Indicates the total number of SAP packets that have been administratively filtered, during nwIpxSapIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxSapIfCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1.1.8
Indicates the total number of SAP packets that have been discarded, during nwIpxSapIfCtrOperationalTime, that were received on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxSapIfCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1.1.9
Indicates the total number of bytes in the SAP packets that have been received, during nwIpxSapIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxSapIfCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1.1.10
Indicates the total number of bytes in the SAP packets that have been transmitted, during nwIpxSapIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxSapIfCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1.1.11
Indicates the total number of bytes in the SAP packets that have been administratively filtered, during nwIpxSapIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxSapIfCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.2.2.1.1.12
Indicates the total number of bytes in the SAP packets that have been discarded, during nwIpxSapIfCtrOperationalTime, that were received on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwIpxSapServerIfTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3.1
The table contains the SAP server table. This table contains an entry for each service learned of through the SAP protocol.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxSapServerIfEntry

nwIpxSapServerIfEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3.1.1
Each entry contains the SAP route information for the Novell server and router port for which the entry exists.
OBJECT-TYPE    
  NwIpxSapServerIfEntry  

nwIpxSapServerIfNetId 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3.1.1.1
This is the primary index into the SAP server table. This number corresponds to the Novell Network Number of the server offering the service. The network number consists of 4 octets.
OBJECT-TYPE    
  IpxAddress  

nwIpxSapServerIfNode 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3.1.1.2
This is a secondary index into the SAP Server Table. This is the MAC-layer address represented as an octetstring of the service offering the server for which the entry exists, represented as an octet string.
OBJECT-TYPE    
  STRING  

nwIpxSapServerIfSocket 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3.1.1.3
This is a secondary index into the SAP Server Table. This is the socket number of the server application for which the entry exists.
OBJECT-TYPE    
  STRING  

nwIpxSapServerIfServiceType 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3.1.1.4
This is a secondary index into the SAP Server Table. This is the service type of the server application for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxSapServerIfIfNum 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3.1.1.5
Indicates the value of MIB 2 ifindex, which identifies the router port through which the service for which the entry exits is available.
OBJECT-TYPE    
  INTEGER  

nwIpxSapServerIfSrcNode 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3.1.1.6
This is the MAC-layer address of the neighbor router from which the service was learned about.
OBJECT-TYPE    
  STRING  

nwIpxSapServerIfName 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3.1.1.7
This is the name of the server offering the service for which the entry exists.
OBJECT-TYPE    
  STRING  

nwIpxSapServerIfHops 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3.1.1.8
Indicates the number of hops required to reach the server offering the service for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxSapServerIfAge 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3.1.1.9
Indicates the amount of time since a SAP update was last received for the server and service for which the entry exits.
OBJECT-TYPE    
  INTEGER  

nwIpxSapServerIfType 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3.1.1.10
Indicates whether the server is on a network that is directly connected through the router port for which the entry exists, or is indirectly connected through another router specified by the value of nwIpxSapServerIfSrcNode.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), direct(3), remote(4)  

nwIpxSapServerIfFlags 1.3.6.1.4.1.52.4.2.2.2.3.2.2.4.1.2.3.1.1.11
Specifies properties of the SAP service for which the entry exist. The bit mask is as follows: source-changed (1), best-source (2), not used (4), net-down (8), not used (16).
OBJECT-TYPE    
  INTEGER  

nwIpxFibTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.5.1
This table contains an entry describing each route being used to forward IPX traffic to each destination Novell network and node.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxFibEntry

nwIpxFibEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.5.1.1
Each entry describes the route to the destination Novell network and node for which the entry exists.
OBJECT-TYPE    
  NwIpxFibEntry  

nwIpxFibNetId 1.3.6.1.4.1.52.4.2.2.2.3.2.2.5.1.1.1
Specifies the Novell Network Number of the destination for which the entry exists. The IpxAddress consists of four octets
OBJECT-TYPE    
  IpxAddress  

nwIpxFibHops 1.3.6.1.4.1.52.4.2.2.2.3.2.2.5.1.1.2
Indicates the number of hops required to reach the destination for which the entry exists. It is considered as metric 1.
OBJECT-TYPE    
  INTEGER  

nwIpxFibTimeTicks 1.3.6.1.4.1.52.4.2.2.2.3.2.2.5.1.1.3
Indicates the amount of time, indicated by the number of TimeTicks, required for a packet to reach the destination network for which the entry exists. It is considered as metric 2.
OBJECT-TYPE    
  TimeTicks  

nwIpxFibNextHopIf 1.3.6.1.4.1.52.4.2.2.2.3.2.2.5.1.1.4
Indicates the router port through which the next hop node is available. Packets destined for the network specified by the value of nwIpxFibNetId will be forwarded on this port.
OBJECT-TYPE    
  INTEGER  

nwIpxFibNextHopNet 1.3.6.1.4.1.52.4.2.2.2.3.2.2.5.1.1.5
Indicates the Novell Network Number portion of the fully formed next hop IPX Address of the next hop node.
OBJECT-TYPE    
  STRING  

nwIpxFibNextHopNode 1.3.6.1.4.1.52.4.2.2.2.3.2.2.5.1.1.6
Indicates the node portion of the fully formed next hop IPX Address.
OBJECT-TYPE    
  MacAddress  

nwIpxFibRouteType 1.3.6.1.4.1.52.4.2.2.2.3.2.2.5.1.1.7
Indicates the status of the route. A value of 3 indicates that the destination is on the network segment that is directly connected to the router port identified by nwIpxFibNextHopIf. A value of 4 indicates that the destination is on an indirectly connected network segment, which is reachable through the next hop router indicated by the value of nwIpxFibNextHopNodeId. A value of 2 indicates that the route is invalid.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), direct(3), remote(4)  

nwIpxAclValidEntries 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7.1
Indicates the number of valid entries that exist in the access control list table.
OBJECT-TYPE    
  Gauge  

nwIpxAclTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7.2
This table contains the access control list information for IPX traffic. This table contains entries, each of which allows packet forwarding between source/destination pairs to be permitted or denied. The list is identified by the Access Control List ID. Each list may contain multiple entries ordered by sequence number. When a particular access control list is searched, it is searched in sequence number order and the first match found ends the search. If no match if found, access defaults to permitted.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxAclEntry

nwIpxAclEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7.2.1
Each entry contains IPX source/destination access information.
OBJECT-TYPE    
  NwIpxAclEntry  

nwIpxAclIdentifier 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7.2.1.1
This is the primary (major) index into the IPX access control list table. This value identifies the access control list by a unique identifier (at least 1) arbitrarily assigned by the user. All entries that have the same value for nwIpxAclIdentifier belong to the same access control list.
OBJECT-TYPE    
  INTEGER  

nwIpxAclSequence 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7.2.1.2
This is the secondary (minor) index into the IPX access control list table. This number corresponds to a sequence number used to order multiple entries within the same access control list.
OBJECT-TYPE    
  INTEGER  

nwIpxAclPermission 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7.2.1.3
Specifies whether access is allowed or denied between the source and destination address pair. Note that source and destination are interchangeable when bi-directional control is selected. To remove an existing entry set nwIpxAclPermission to invalid (2). Invalid entries disappear after reboot.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), permit(3), deny(4), permit-bidirectional(5), deny-bidirectional(6)  

nwIpxAclMatches 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7.2.1.4
Indicates the number of matches on this entry that have resulted in the permit/deny access restriction being applied as part of the forwarding process.
OBJECT-TYPE    
  Counter  

nwIpxAclDestNetNum 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7.2.1.5
Specifies the destination Novell Network Number used to compare for matches on the access control list. A 0 value is a wildcard which matches any Novell Network Number.
OBJECT-TYPE    
  STRING  

nwIpxAclDestNode 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7.2.1.6
Specifies the MAC-layer address of the destination node (represented as an octet string), used to compare for matches on the access control list. A value 0 is a wildcard, which matches any node.
OBJECT-TYPE    
  STRING  

nwIpxAclDestSocket 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7.2.1.7
Specifies the socket number of the destination socket used to compare for matches on the access control list. A 0 value is a wildcard matching any socket.
OBJECT-TYPE    
  STRING  

nwIpxAclSrcNetNum 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7.2.1.8
Specifies the Novell Network Number of the source Novell Network used to compare for matches on the access control list. A 0 value is a wildcard matching any Novell Network Number.
OBJECT-TYPE    
  STRING  

nwIpxAclSrcNode 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7.2.1.9
Specifies the MAC-layer address of the source node (represented as an octet string), used to compare for matches on the Access Control List. A 0 value is a wildcard matching any node.
OBJECT-TYPE    
  STRING  

nwIpxAclSrcSocket 1.3.6.1.4.1.52.4.2.2.2.3.2.2.7.2.1.10
Specifies the socket number of the source socket to compare for matches on the Access Control List. A 0 value is a wildcard matching any socket.
OBJECT-TYPE    
  STRING  

nwIpxNetBIOSAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.1.1
Sets the administrative state of the NetBIOS Broadcast Redirector, system-wide. Enabled (3) causes the NetBios Broadcast Redirector to become active on any router port configured and enabled for IPX Routing Services. Disabled (2) causes the NetBIOS Broadcast Redirector to perform a graceful shut-down on any active IPX router port.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxNetBIOSOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.1.2
Indicates the current operating condition of the NetBIOS Broadcast Redirector, system-wide.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5), invalid-config(6)  

nwIpxNetBIOSAdminReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.1.3
Resets the NetBIOS Broadcast Redirector, system-wide. Reset (2) forces a restart of the NetBIOS Broadcast Redirector without a graceful shut-down on any active router port and without effecting any other router application.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxNetBIOSOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwIpxNetBiosOperStatus has been in the current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxNetBIOSVersion 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.1.5
Indicates the current revision level of the NetBIOS Broadcast Redirector firmware, in textual format.
OBJECT-TYPE    
  DisplayString  

nwIpxNetBIOSCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.2.1
Sets the administrative state of the aggregate (system-wide) NetBIOS broadcast packet and byte counters. Enabled (3) causes these counters to become active on all router port. Disabled (2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxNetBIOSCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.2.2
Resets the aggregate (system-wide) NetBIOS broadcast packet and byte counters. Reset (2) resets the NetBIOS broadcast aggregate counters to 0. nwIpxNetBIOSCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxNetBIOSCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.2.3
Indicates the elapsed time, in hundreds of a second, that the nwIpxNetBIOSCtrAdminStatus has been in the current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxNetBIOSCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.2.4
Indicates the total number of NetBIOS broadcast packets that have been received, system-wide, during nwIpxNetBIOSCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.2.5
Indicates the total number of NetBIOS broadcast packets that have been transmitted, system-wide, during nwIpxNetBIOSCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.2.6
Indicates the total number of NetBIOS broadcast packets that have been administratively filtered, system-wide, during nwIpxNetBIOSCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.2.7
Indicates the total number of NetBIOS broadcast packets that have been discarded, system-wide, during nwIpxNetBIOSCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.2.8
Indicates the total number of bytes in the NetBIOS packets that have been received, system-wide, during nwIpxNetBIOSCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.2.9
Indicates the total number of bytes in the NetBIOS packets that have been transmitted, system-wide, during nwIpxNetBIOSCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.2.10
Indicates the total number of bytes in the NetBIOS packets that have been administratively filtered, system-wide, during nwIpxNetBIOSCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.1.2.11
Indicates the total number of bytes in the NetBIOS packets that have been discarded, system-wide, during nwIpxNetBIOSCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSIfTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.1.1
This table contains an entry for each router port. Each entry can contain different values, allowing the NetBIOS Broadcast Redirector configuration to vary from router port to router port. This table is indexed by nwIpxNetBIOSIfIndex, which indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxNetBIOSIfEntry

nwIpxNetBIOSIfEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.1.1.1
Each entry contains the IPX NetBIOS broadcasting configuration for the router port for which the entry exists.
OBJECT-TYPE    
  NwIpxNetBIOSIfEntry  

nwIpxNetBIOSIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.1.1.1.1
Indicates the value in MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxNetBIOSIfAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.1.1.1.2
Sets the administrative state of IPX NetBIOS broadcasting on the router port for which the entry exists. Enabled (3) causes this router port to become active. Disabled (2) causes it to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxNetBIOSIfOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.1.1.1.3
Indicates the current operating condition of IPX NetBIOS broadcasting on the IPX router port for which the entry exists.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5), invalid-config(6)  

nwIpxNetBIOSIfOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that IPX NetBIOS broadcasting, nwIpxNetBIOSIfOperStatus, has been in its current state on the router port for which the entry exists.
OBJECT-TYPE    
  TimeTicks  

nwIpxNetBIOSIfCtrTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1
This table contains the IPX NetBIOS packet and byte counters for each router port on this device.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxNetBIOSIfCtrEntry

nwIpxNetBIOSIfCtrEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1.1
This is the primary index into the NetBIOS Interface Counter Table. This number corresponds to the index into the MIB 2 Interface Table which describes the router port for which this entry exists.
OBJECT-TYPE    
  NwIpxNetBIOSIfCtrEntry  

nwIpxNetBIOSIfCtrIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1.1.1
This is the primary index into the IPX NetBIOS Interface Counter Table. This number correspoonds to the index into the MIB 2 Interface Table which describes the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxNetBIOSIfCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1.1.2
Sets the administrative state of the IPX NetBIOS packet and bytes counters on the IPX router port for which the entry exists. Enabled (3) causes these counters to become active on the configured NetBIOS router port. Disabled (2) causes thes counters to become inactive on the configured NetBIOS router port.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxNetBIOSIfCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1.1.3
Resets the NetBIOS packet and bvyte counters on the router port for which the entry exists. Reset (2) resets the interface-specific counters to 0. nwIpxNetBIOSIfCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxNetBIOSIfCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1.1.4
Indicates the amount of time, in hundredths of a second, that the interface-specific NetBIOS packet and byte counters have been active on the router port for which the entry exists.
OBJECT-TYPE    
  TimeTicks  

nwIpxNetBIOSIfCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1.1.5
Indicates the total number of NetBIOS packets that have been recieved, on the router port for which the entry exists, during nwIpxNetBIOSIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSIfCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1.1.6
Indicates the total number of NetBIOS packets that have been transmitted, on the router port for which the entry exists, during nwIpxNetBIOSIfCtrOperationallTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSIfCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1.1.7
Indicates the total number of NetBIOS packets that have been administratively filtered, on the router port for which the entry exists, during nwIpxNetBIOSIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSIfCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1.1.8
Indicates the total number of NetBIOS packets that have been discarded, on the router port for which the entry exists, during nwIpxNetBIOSIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSIfCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1.1.9
Indicates the total number of bytes in the NetBIOS packets that have been recieved, on the router port for which the entry exists, during nwIpxNetBIOSIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSIfCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1.1.10
Indicates the total number of bytes in the NetBIOS packets that have been transmitted, on the router port for which the entry exists, during nwIpxNetBIOSIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSIfCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1.1.11
Indicates the total number of bytes in the NetBIOS packets that have been administratively filtered, that were recieved on the router port for which the entry exists during nwIpxNetBIOSIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxNetBIOSIfCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.1.2.2.1.1.12
Indicates the total number of bytes in the NetBIOS packets that have been discarded, on the router port for which the entry exists, during nwIpxNetBIOSIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.1.1
Sets the administrative state of IPX Broadcast. Enabled (3) casuses IPX Broadcast to become active on any configured IPX router port. Disabled (2) causes IPX Broadcast to perform a graceful shutdown on any active IPX router ports.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxBcastOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.1.2
Indicates the current operating condition of the IPX Broadcast.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5), invalid-config(6)  

nwIpxBcastAdminReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.1.3
Resets the IPX Broadcast. Reset (2) will force a restart of the IPX Broadcast without a graceful shutdown on any active IPX router port, without effecting any other router applications.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxBcastOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.1.4
Indicates the amount of time, in hundredths of a second, that IPX Broadcast has been in its current operational state.
OBJECT-TYPE    
  TimeTicks  

nwIpxBcastVersion 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.1.5
Indicates the current revision level of IPX Broadcast.
OBJECT-TYPE    
  DisplayString  

nwIpxBcastCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.2.1
Sets the administrative state of the aggregate (device-wide) Broadcast packet and byte counters. enable (3) causes these counters to become active on any router port running Broadcast. disabled (2) causes these counters to become inactive on all router port running Broadcast.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxBcastCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.2.2
Resets the aggregate (device-wide) IPX Broadcast packet and byte counters. Reset (2) resets the IPX Broadcast aggregate counters to 0. nwIpxBcasstCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxBcastCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.2.3
Indicates the amount of time, in hundredths of a second, that the aggregate (device-wide) IPX Broadcast packet and byte counters have been in the current administrative state.
OBJECT-TYPE    
  TimeTicks  

nwIpxBcastCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.2.4
Indicates the total number of IPX Broadcast packets that have been received, device-wide, during nwIpxBcastCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.2.5
Indicates the total number of IPX Broadcast packets that have been transmitted, device-wide, during nwIpxBcastCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.2.6
Indicates the total number of IPX Broadcast packets that have been administaratively filtered, device-wide, during nwIpxBcastCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.2.7
Indicates the total number of IPX Broadcast packets that have been discarded, device-wide, during nwIpxBcastCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.2.8
Indicates the total number of IPX Broadcast packets that have been recieved, device-wide, during nwIpxBcastCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.2.9
Indicates the total number of IPX Broadcast packets that have been transmitted, device-wide, during nwIpxBcastCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.2.10
Indicates the total number of bytes in the IPX Broadcast packets that have been administratively filtered, device-wide, during nwIpxBcastOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.1.2.11
Indicates the total number of bytes in the Broadcast packets that have been discarded, during nwIpxBcastCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastIfTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.1.1
This table contains an entry for each router port configured for the IPX distance-vector based routing protocol. Each entry can contain different values, allowing the routing protocol configuration to vary from router port to router port. This table is indexed by nwIpxBcastIfIndex, which indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxBcastIfEntry

nwIpxBcastIfEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.1.1.1
Specifies the IPX Broadcast configuration information for the logical IPX interface for which this entry exists.
OBJECT-TYPE    
  NwIpxBcastIfEntry  

nwIpxBcastIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.1.1.1.1
This index corresponds to the primary index into the MIB 2 Interface Table, which describes the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxBcastIfAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.1.1.1.2
Sets the administrative state of the IPX Broadcast on the router port for which the entry exists. Enabled (2) causes IPX Broadcast on this router port to become active. Disabled (2) causes IPX Broadcast to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxBcastIfOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.1.1.1.3
Indicates the current operating condition of the IPX Broadcast on the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5), invalid-config(6)  

nwIpxBcastIfOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwIPXBcastIfOperStatus has been in its current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxBcastIfCtrTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1
This table contains the IPX Broadcast packet and byte counters for each router port on this device.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxBcastIfCtrEntry

nwIpxBcastIfCtrEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1.1
This is the primary index into the Broadcast Interface Counter Table. This number corresponds to the index into the MIB 2 Interface Table which describes the router port for which the entry exists.
OBJECT-TYPE    
  NwIpxBcastIfCtrEntry  

nwIpxBcastIfCtrIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1.1.1
This is the primary index into the IPX Broadcast Interface Counter Table. This number corresponds to the index into the MIB 2 Interface Table which describes the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxBcastIfCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1.1.2
Sets the administrative state of the IPX Broadcast packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters to become acive on the configured IPX Broadcast router port. Disabled (2) causes these counters to become inactive on the configured IPX Broadcast router port.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxBcastIfCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1.1.3
Resets the IPX Broadcast packet and byte counters on the router port for which the entry exists. Reset (2) resets the interface-specific counters to 0. nwIpxBcastIfCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxBcastIfCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1.1.4
Indicates the amount of time, in hundredths of a second, that the interface-specific IPX Broadcast packet and byte counters have been in the current administrative state on the router port for which the entry exists.
OBJECT-TYPE    
  TimeTicks  

nwIpxBcastIfCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1.1.5
Indicates the total number of IPX Broadcast packets that have been recieved, on the router port for which the entry exists, during nwIpxBcastIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastIfCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1.1.6
Indicates the total number of Broadcast packets that have been transmitted, on the router port for which the entry existsl, during nwIpxBcastIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastIfCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1.1.7
Indicates the total number of IPX Broadcast packets that have been administratively filtered, on the router port for which the entry exists, during nwIpxBcastIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastIfCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1.1.8
Indicates the total number of Broadcast packets that have been dis- carded, on the router port for which the entry exists, during nwIpxBcastIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastIfCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1.1.9
Indicates the total number of bytes in the IPX Broadcast packets that have been recieved, on the router port for which the entry exists, during nwIpxBcastIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastIfCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1.1.10
Indicates the total number of bytes in the IPX Broadcast packets that have been transmitted, on the router port for which the entry exists, during nwIpxBcastIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastIfCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1.1.11
Indicates the total number of bytes in the IPX Broadcast packets that have been administratively filtered on the router port for which the entry exists during nwIpxBcastIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxBcastIfCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.2.2.2.1.1.12
Indicates the total number of bytes in the IPX Broadcast packets that have been discarded on the router port for which the entry exists, during nwIpxBcastIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.1.1
Sets the administrative state of the IPX Echo. Enabled (3) causes IPX ECHO to become active on any configured IPX router ports. Disabled (2) causes IPX Echo to perform a graceful shutdown on any active IPX router port.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxEchoOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.1.2
Indicates the operating condition of IPX Echo.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5), invalid-config(6)  

nwIpxEchoAdminReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.1.3
Resets IPX Echo. Reset (2) will force a restart of IPX Echo without a graceful shutdown on any active IPX router port, without effecting any other router applications.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxEchoOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.1.4
Indicates the amount of time, in hundredths of a second, that IPX Echo has been in its current administrative state, nwIpxEchoOperStatus.
OBJECT-TYPE    
  TimeTicks  

nwIpxEchoVersion 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.1.5
Indicates the current revision level of IPX Echo firmware.
OBJECT-TYPE    
  DisplayString  

nwIpxEchoCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.2.1
Sets the administrative state of the aggregae (device-wide) IPX Echo packet and byte counters. Enabled (3) causes these counters to become active on any router port running IPX Echo. Disabled (2) causes these counters to become inactive on all router ports.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxEchoCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.2.2
Resets the aggregate (device-wide) IPX Echo packet and byte counters. Reset (2) resets the IPX Echo aggregate counters to 0. nwIpxEchoCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxEchoCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.2.3
Indicates the amount of time, in hundredths of a second, that the aggreagate (device-wide) IPX Echo packet and byte counters have been in the current administrative state.
OBJECT-TYPE    
  TimeTicks  

nwIpxEchoCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.2.4
Indicates the total number of IPX Echo packets that have been recieved, device-wide, during nwIpxEchoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.2.5
Indicates the total number of IPX Echo packets that have been transmitted, device-wide, during nwIpxEchoCtrOperationalTIme.
OBJECT-TYPE    
  Counter  

nwIpxEchoCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.2.6
Indicates the total number of IPX Echo packets that have been administratively filtered, device-wide, during nwIpxEchoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.2.7
Indicates the total number of IPX Echo packets that have been discarded, device-wide, during nwIpxEchoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.2.8
Indicates the total number of IPX Echo packets that have been recieved, device-wide, during nwIpxEchoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.2.9
Indicates the total number of IPX Echo packets that have been transmitted, device-wide, during nwIpxEchoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.2.10
Indicates the total number of IPX Echo packets that have been administratively filtered, device-wide, during nwIpxEchoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoSCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.1.2.11
Indicates the total number of bytes in the Echo packets that have been discarded, during nwIpxEchoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoIfTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.1.1
This table contains an entry for each router port configured for IPX Echo. Each entry can contain different values, allowing the routing protocol configuration to vary from router port to router port. This table is indexed by nwIpxEchoIfIndex, which indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxEchoIfEntry

nwIpxEchoIfEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.1.1.1
Specifies the IPX Echo information for the logical IPX interface for which the entry exists.
OBJECT-TYPE    
  NwIpxEchoIfEntry  

nwIpxEchoIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.1.1.1.1
This index corresponds to the primary index into the MIB 2 ifTable, which describes the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxEchoIfAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.1.1.1.2
Sets the administrative state of IPX Echo on the router port for which the entry exists. Enabled (2) causes this router port to become active. Disabled (3) causes this router port to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxEchoIfOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.1.1.1.3
Indicates the current operating condition of IPX Echo on the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5), invalid-config(6)  

nwIpxEchoIfOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwIpxEchoIfAdminStatus has been in its current state.
OBJECT-TYPE    
  TimeTicks  

nwIpxEchoIfCtrTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1
This table contains the IPX Echo packet and byte counters for each router port on this device.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxEchoIfCtrEntry

nwIpxEchoIfCtrEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1.1
This is the primary index into the Echo Interface Counter Table. This number corresponds to the index into the MIB 2 Interface Table which describes the router port for which the entry exists.
OBJECT-TYPE    
  NwIpxEchoIfCtrEntry  

nwIpxEchoIfCtrIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1.1.1
This is the primary index into the IPX Echo Interface Counter Table. This number corresponds to the index into the MIB 2 Interfcace Table which describes the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxEchoIfCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1.1.2
Sets the administrative state of the IPX Echo packet and byte counters on the IPX router port for which the entry exists. Enabled (3) causes these counters to become active on the router port configured for IPX Echo. Disabled (2) causes these counters to become inactive on the configured IPX Echo router port.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxEchoIfCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1.1.3
Resets the IPX Echo packet andbyte counters on the router port for which the entryexists. Reset (2) resets the interface-specific counters to 0. nwIpxEchoIfCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwIpxEchoIfCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1.1.4
Indicates the amount of time, in hundredths of a second, that the interface-specific IPX Echo packet and byte counters have been in the current administrative state on the router port for which the entry exists.
OBJECT-TYPE    
  TimeTicks  

nwIpxEchoIfCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1.1.5
Indicates the total number of IPX Echo packets that have been recieved, on the router port for which the entry exists, during nwIpxEchoIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoIfCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1.1.6
Indicates the total number of IPX Echo packets that have been transmitted, on the router port for which the entry exists, during nwIpxEchoIfCrOperationalTIme.
OBJECT-TYPE    
  Counter  

nwIpxEchoIfCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1.1.7
Indicates the total number of IPX Echo packets that have been administratively filtered, on the router port for which the entry exists, during nwIpxEchoIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoIfCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1.1.8
Indicates the total number of IPX Echo packets that have been discaded, on the router port for which the entry exists, during nwIpxEchoIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoIfCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1.1.9
Indicates the total number of bytes in the IPX Echo packets that have been recieved, on the router port for which the entry exists, during nwIpxEchoIfCtrOpeationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoIfCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1.1.10
Indicates the total number of bytes in the IPX Echo packets that have been transmitted, on the router port for which the entry exists, during nwIpxEchoIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoIfCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1.1.11
Indicates the total number of bytes in the IPX Echo packets that have been administratively filtered and recieved on the router port for which the entry exists, during nwIpxEchoIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxEchoIfCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.2.2.9.3.2.2.1.1.12
Indicates the total number of bytes in the IPX Echo packets that have been discarded, that were recieved on the router port for which the entry exists, during nwIpxEchoIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwIpxHostMapTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.6.3.1
The Ipx Address translation table used for mapping an IPX address to a circuit identifier (if applicable), corresponding port number, and framing type.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxHostMapEntry

nwIpxHostMapEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.6.3.1.1
Each entry contains one IpxAddress to circuit equivalence. Also provided is the framing required to converse with this host, and the corresponding logical port number.
OBJECT-TYPE    
  NwIpxHostMapEntry  

nwIpxHostMapIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.2.2.6.3.1.1.1
This is the primary (major) index into the Ipx HostMap table. This number corresponds to the index into the MIB-2 Interfaces Group which describes the IPX router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwIpxHostMapIpxAddr 1.3.6.1.4.1.52.4.2.2.2.3.2.2.6.3.1.1.2
The IpxAddress of the host on the corresponding interface and circuit (if applicable). The IpxAddress consists of a network number of 4 octets followed by 6 octets of node identifier.
OBJECT-TYPE    
  IpxAddress  

nwIpxHostMapPhysAddr 1.3.6.1.4.1.52.4.2.2.2.3.2.2.6.3.1.1.3
The media-dependent 'physical' address. The value of this object is 0 for entries indicating native-wan(8) framing.
OBJECT-TYPE    
  PhysAddress  

nwIpxHostMapType 1.3.6.1.4.1.52.4.2.2.2.3.2.2.6.3.1.1.4
Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the nwIpxHostMapTable. That is, it effectively dissasociates the circuit and/or interface identified with said entry from the mapping identified with said entry. It is an implementation- specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper inter- pretation of such entries requires examination of the relevant wIpxHostMapType object.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), dynamic(3), static(4), inactive(5)  

nwIpxHostMapCircuitID 1.3.6.1.4.1.52.4.2.2.2.3.2.2.6.3.1.1.5
The identifier for the virtual circuit present on the interface. On an interface configured for Frame Relay, this number is the DLCI for the IPX Address at the end of the circuit. For non-WAN interfaces, the value of this object is zero.
OBJECT-TYPE    
  INTEGER  

nwIpxHostMapFraming 1.3.6.1.4.1.52.4.2.2.2.3.2.2.6.3.1.1.6
Specifies the framing type required to converse with the host for which this entry exists.
OBJECT-TYPE    
  INTEGER other(1), ethernet(2), snap(3), i8022(4), novell(6), nativewan(8), encapenet(9), encapenet8022(10), encapenetsnap(11), encapenetnovell(12), encaptr8022(13), encaptrsnap(14), encapfddi8022(15), encapfddisnap(16), canonical(17)  

nwIpxHostMapPortNumber 1.3.6.1.4.1.52.4.2.2.2.3.2.2.6.3.1.1.7
The unique value for the logical port number. It's value ranges between 1 and a maximum value which is dependent on both the number of configured interfaces in the system and the number of circuits present on those interfaces which are of WAN type.
OBJECT-TYPE    
  INTEGER  

nwIpxEventAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.1.1
Sets the administrative state of IPX event logging. Enabled (3) causes the event log to become active. Disabled (2) causes the event log to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxEventMaxEntries 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.1.2
Sets the maximum size of the event log table. When the table size exceeds the maximum, the first entry is deleted until the size of the table does not exceed the maximum.
OBJECT-TYPE    
  INTEGER  

nwIpxEventTraceAll 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.1.3
Sets the administrative state of the event log. Enabled (3) allows logging of all event types on all router ports from all protocols and components. Disabled (2) causes the filter table to specify which events to log.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwIpxEventFilterTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.2.1
This table contains an entry for each event filter configured for IPX Routing Services events.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxEventFilterEntry

nwIpxEventFilterEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.2.1.1
Each entry describes an event filter which defines a particular type of event to be logged to the event log. The nwIpxEventProtocol refers to the instance used in the nwRtgProtocolTable and nwComponentTable specified by the Cabletron Routing Services MIB, and identifies the protocol to which the entry applies.
OBJECT-TYPE    
  NwIpxEventFilterEntry  

nwIpxEventFltrProtocol 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.2.1.1.1
Specifies the routing protocol involved in the event for which the event filter exists.
OBJECT-TYPE    
  INTEGER  

nwIpxEventFltrIfNum 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.2.1.1.2
Specifies the router port involved in the event for which the event filter exists.
OBJECT-TYPE    
  INTEGER  

nwIpxEventFltrControl 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.2.1.1.3
Set this value to 3 to add the event filter to the Event Filter Table. Set this value to 2 to delete the event filter from the Event Filter Table.
OBJECT-TYPE    
  INTEGER other(1), delete(2), add(3)  

nwIpxEventFltrType 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.2.1.1.4
This 6 bit mask specifies the types of events to be logged. By default all 6 bits are set to 1, indicating that all types of events will be logged. Setting any bit to 0 removes an event type from this field and prevents that type of event from being logged. Adding event types to this field will enable those types of events to be logged.
OBJECT-TYPE    
  INTEGER misc(1), timer(2), rcv(4), xmit(8), event(16), error(32)  

nwIpxEventFltrSeverity 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.2.1.1.5
This object controls the amount of logging by ignoring events of lower priority than specified by this filter value. The highest value will ignore all events except those of the highest severity. `Highmed' will log all events highest priority through lowest. `Highlow' will log all events highest priority through lowest. The `highmed' severity is the default setting.
OBJECT-TYPE    
  INTEGER highest(1), highmed(2), highlow(3)  

nwIpxEventFltrAction 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.2.1.1.6
This field specifies how the events are to be logged. Logging to the `log' stores the events in the event log table. Logging to `trap' sends events out through the trap mechanism.
OBJECT-TYPE    
  INTEGER log(1), trap(2), log-trap(3)  

nwIpxEventTable 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.3.1
This table contains an entry for each event that has been logged.
OBJECT-TYPE    
  SEQUENCE OF  
    NwIpxEventEntry

nwIpxEventEntry 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.3.1.1
Each entry contains the information about an event that has been logged to the event table.
OBJECT-TYPE    
  NwIpxEventEntry  

nwIpxEventNumber 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.3.1.1.1
An ordinal value assigned to the event for which the entry exists. nwIpxEventNumber is assigned so that each event in the event log can be uniquely identified by the value of nwIpxEventNumber.
OBJECT-TYPE    
  INTEGER  

nwIpxEventTime 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.3.1.1.2
Indicates the time at which the event was logged to the event log.
OBJECT-TYPE    
  TimeTicks  

nwIpxEventType 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.3.1.1.3
Indicates the type of event that was logged.
OBJECT-TYPE    
  INTEGER misc(1), timer(2), rcv(4), xmit(8), event(16), error(32)  

nwIpxEventSeverity 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.3.1.1.4
Indicates the priority that was assigned to this type event.
OBJECT-TYPE    
  INTEGER highest(1), highmed(2), highlow(3)  

nwIpxEventProtocol 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.3.1.1.5
Indicates the routing protocol that was involved in this event.
OBJECT-TYPE    
  INTEGER  

nwIpxEventIfNum 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.3.1.1.6
Indicates the router port that was involved in the event.
OBJECT-TYPE    
  INTEGER  

nwIpxEventTextString 1.3.6.1.4.1.52.4.2.2.2.3.2.2.10.3.1.1.7
Contains the actual text string that was logged.
OBJECT-TYPE    
  STRING