CTRON-APPN-MIB

File: CTRON-APPN-MIB.mib (138069 bytes)

Imported modules

RFC-1212 ROUTER-OIDS RFC1213-MIB
RFC1155-SMI

Imported symbols

OBJECT-TYPE nwRtrProtoSuites DisplayString
Counter TimeTicks

Defined Types

NwAppnSysLuEntry  
SEQUENCE    
  nwAppnSysCpName DisplayString
  nwAppnSysLuName DisplayString
  nwAppnSysLuControl INTEGER

NwAppnFwdIfEntry  
SEQUENCE    
  nwAppnFwdIfIndex INTEGER
  nwAppnFwdIfAdminStatus INTEGER
  nwAppnFwdIfOperStatus INTEGER
  nwAppnFwdIfOperationalTime TimeTicks
  nwAppnFwdIfControl INTEGER
  nwAppnFwdIfMtu INTEGER
  nwAppnFwdIfForwarding INTEGER
  nwAppnFwdIfFrameType INTEGER
  nwAppnFwdIfAclIdentifier INTEGER
  nwAppnFwdIfAclStatus INTEGER
  nwAppnFwdIfCacheControl INTEGER
  nwAppnFwdIfCacheEntries Counter
  nwAppnFwdIfCacheHits Counter
  nwAppnFwdIfCacheMisses Counter

NwAppnExtEntry  
SEQUENCE    
  nwAppnExtIfIndex INTEGER
  nwAppnExtIfPortName DisplayString
  nwAppnExtIfPortType INTEGER
  nwAppnExtIfDlcType INTEGER
  nwAppnExtIfMaxRBtuSize INTEGER
  nwAppnExtIfTotLsActLim INTEGER
  nwAppnExtIfInbLsActLim INTEGER
  nwAppnExtIfOutbLsActLim INTEGER
  nwAppnExtIfLocalLsRole INTEGER
  nwAppnExtIfActXidXchgLimit INTEGER
  nwAppnExtIfNonActXidXchgLimit INTEGER
  nwAppnExtIfLsXmitRcvCap INTEGER
  nwAppnExtIfMaxIfrmRcvd INTEGER
  nwAppnExtIfDfltTargetPacing INTEGER
  nwAppnExtIfDfltMaxSBtuSize INTEGER
  nwAppnExtIfDfltEffectCap INTEGER
  nwAppnExtIfDfltConnectCost INTEGER
  nwAppnExtIfDfltByteCost INTEGER
  nwAppnExtIfDfltSecurity INTEGER
  nwAppnExtIfDfltPropDelay INTEGER
  nwAppnExtIfDfltUsrDef1 INTEGER
  nwAppnExtIfDfltUsrDef2 INTEGER
  nwAppnExtIfDfltUsrDef3 INTEGER
  nwAppnExtIfStopType INTEGER
  nwAppnExtIfCpCpSupp INTEGER
  nwAppnExtIfLimitedRsrc INTEGER
  nwAppnExtIfAddress OCTET STRING
  nwAppnExtIfSsap OCTET STRING

NwAppnIfCnPortEntry  
SEQUENCE    
  nwAppnIfCnPtFqName DisplayString
  nwAppnIfCnPtName DisplayString
  nwAppnIfCnPtControl INTEGER

NwAppnIfCnTgCharEntry  
SEQUENCE    
  nwAppnIfCnTgFqName DisplayString
  nwAppnIfCnTgEffectCap INTEGER
  nwAppnIfCnTgConnectCost INTEGER
  nwAppnIfCnTgByteCost INTEGER
  nwAppnIfCnTgSecurity INTEGER
  nwAppnIfCnTgPropDelay INTEGER
  nwAppnIfCnTgUsrDef1 INTEGER
  nwAppnIfCnTgUsrDef2 INTEGER
  nwAppnIfCnTgUsrDef3 INTEGER

NwAppnFwdIfCtrEntry  
SEQUENCE    
  nwAppnFwdIfCtrIfIndex INTEGER
  nwAppnFwdIfCtrAdminStatus INTEGER
  nwAppnFwdIfCtrReset INTEGER
  nwAppnFwdIfCtrOperationalTime TimeTicks
  nwAppnFwdIfCtrInMus Counter
  nwAppnFwdIfCtrOutMus Counter
  nwAppnFwdIfCtrFwdMus Counter
  nwAppnFwdIfCtrFilteredMus Counter
  nwAppnFwdIfCtrDiscardMus Counter
  nwAppnFwdIfCtrAddrErrMus Counter
  nwAppnFwdIfCtrLenErrMus Counter
  nwAppnFwdIfCtrHdrErrMus Counter
  nwAppnFwdIfCtrInBytes Counter
  nwAppnFwdIfCtrOutBytes Counter
  nwAppnFwdIfCtrFwdBytes Counter
  nwAppnFwdIfCtrFilteredBytes Counter
  nwAppnFwdIfCtrDiscardBytes Counter
  nwAppnFwdIfCtrHostInMus Counter
  nwAppnFwdIfCtrHostOutMus Counter
  nwAppnFwdIfCtrHostDiscardMus Counter
  nwAppnFwdIfCtrHostInBytes Counter
  nwAppnFwdIfCtrHostOutBytes Counter
  nwAppnFwdIfCtrHostDiscardBytes Counter

NwAppnFwdLsEntry  
SEQUENCE    
  nwAppnFwdLsName DisplayString
  nwAppnFwdLsAdminStatus INTEGER
  nwAppnFwdLsOperStatus INTEGER
  nwAppnFwdLsOperationalTime TimeTicks
  nwAppnFwdLsControl INTEGER
  nwAppnFwdLsPortName DisplayString
  nwAppnFwdLsAdjCpName DisplayString
  nwAppnFwdLsAdjCpType INTEGER
  nwAppnFwdLsAutoActSupport INTEGER
  nwAppnFwdLsLimitedRsrc INTEGER
  nwAppnFwdLsSscpSession INTEGER
  nwAppnFwdLsPuName DisplayString
  nwAppnFwdLsBackLvlLenEN INTEGER
  nwAppnFwdLsCpCpSessSupp INTEGER
  nwAppnFwdLsEffectCap INTEGER
  nwAppnFwdLsConnectCost INTEGER
  nwAppnFwdLsByteCost INTEGER
  nwAppnFwdLsSecurity INTEGER
  nwAppnFwdLsPropDelay INTEGER
  nwAppnFwdLsUsrDef1 INTEGER
  nwAppnFwdLsUsrDef2 INTEGER
  nwAppnFwdLsUsrDef3 INTEGER
  nwAppnFwdLsTrgtPacingCount INTEGER
  nwAppnFwdLsMaxSendBtu INTEGER
  nwAppnFwdLsNumActiveSession INTEGER
  nwAppnFwdLsdynamicLs INTEGER
  nwAppnFwdLsStopType INTEGER
  nwAppnFwdLsPortNbr INTEGER
  nwAppnFwdLsDestAddr OCTET STRING
  nwAppnFwdLsDsap OCTET STRING
  nwAppnFwdLsBlockNum DisplayString
  nwAppnFwdLsIdNum DisplayString

NwAppnFwdLsCtrEntry  
SEQUENCE    
  nwAppnFwdLsCtrLsName DisplayString
  nwAppnFwdLsCtrAdminStatus INTEGER
  nwAppnFwdLsCtrReset INTEGER
  nwAppnFwdLsCtrOperationalTime TimeTicks
  nwAppnFwdLsCtrInBlus Counter
  nwAppnFwdLsCtrOutBlus Counter
  nwAppnFwdLsCtrFwdBlus Counter
  nwAppnFwdLsCtrFilteredBlus Counter
  nwAppnFwdLsCtrDiscardBlus Counter
  nwAppnFwdLsCtrAddrErrBlus Counter
  nwAppnFwdLsCtrLenErrBlus Counter
  nwAppnFwdLsCtrHdrErrBlus Counter
  nwAppnFwdLsCtrInBytes Counter
  nwAppnFwdLsCtrOutBytes Counter
  nwAppnFwdLsCtrFwdBytes Counter
  nwAppnFwdLsCtrFilteredBytes Counter
  nwAppnFwdLsCtrDiscardBytes Counter
  nwAppnFwdLsCtrHostInBlus Counter
  nwAppnFwdLsCtrHostOutBlus Counter
  nwAppnFwdLsCtrHostDiscardBlus Counter
  nwAppnFwdLsCtrHostInBytes Counter
  nwAppnFwdLsCtrHostOutBytes Counter
  nwAppnFwdLsCtrHostDiscardBytes Counter

NwAppnEventFilterEntry  
SEQUENCE    
  nwAppnEventFltrProtocol INTEGER
  nwAppnEventFltrIfNum INTEGER
  nwAppnEventFltrControl INTEGER
  nwAppnEventFltrType INTEGER
  nwAppnEventFltrSeverity INTEGER
  nwAppnEventFltrAction INTEGER

NwAppnEventEntry  
SEQUENCE    
  nwAppnEventNumber INTEGER
  nwAppnEventTime TimeTicks
  nwAppnEventType INTEGER
  nwAppnEventSeverity INTEGER
  nwAppnEventProtocol INTEGER
  nwAppnEventIfNum INTEGER
  nwAppnEventTextString OCTET STRING

Defined Values

nwAppnRouter 1.3.6.1.4.1.52.4.2.2.2.3.5
OBJECT IDENTIFIER    

nwAppnMibs 1.3.6.1.4.1.52.4.2.2.2.3.5.1
OBJECT IDENTIFIER    

nwAppnComponents 1.3.6.1.4.1.52.4.2.2.2.3.5.2
OBJECT IDENTIFIER    

nwAppnSystem 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1
OBJECT IDENTIFIER    

nwAppnForwarding 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2
OBJECT IDENTIFIER    

nwAppnTopology 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4
OBJECT IDENTIFIER    

nwAppnFib 1.3.6.1.4.1.52.4.2.2.2.3.5.2.5
OBJECT IDENTIFIER    

nwAppnEndSystems 1.3.6.1.4.1.52.4.2.2.2.3.5.2.6
OBJECT IDENTIFIER    

nwAppnAccessControl 1.3.6.1.4.1.52.4.2.2.2.3.5.2.7
OBJECT IDENTIFIER    

nwAppnFilters 1.3.6.1.4.1.52.4.2.2.2.3.5.2.8
OBJECT IDENTIFIER    

nwAppnRedirector 1.3.6.1.4.1.52.4.2.2.2.3.5.2.9
OBJECT IDENTIFIER    

nwAppnEvent 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10
OBJECT IDENTIFIER    

nwAppnWorkGroup 1.3.6.1.4.1.52.4.2.2.2.3.5.2.11
OBJECT IDENTIFIER    

nwAppnSysConfig 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1
OBJECT IDENTIFIER    

nwAppnSysAdministration 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.2
OBJECT IDENTIFIER    

nwAppnSysCfgLocalNode 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2
OBJECT IDENTIFIER    

nwAppnSysCfgTables 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.3
OBJECT IDENTIFIER    

nwAppnFwdSystem 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1
OBJECT IDENTIFIER    

nwAppnFwdInterfaces 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2
OBJECT IDENTIFIER    


nwAppnFwdCounters 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1
OBJECT IDENTIFIER    

nwAppnFwdIfConfig 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1
OBJECT IDENTIFIER    

nwAppnIfCn 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3
OBJECT IDENTIFIER    

nwAppnFwdIfCounters 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2
OBJECT IDENTIFIER    

nwAppnFwdLsConfig 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1
OBJECT IDENTIFIER    

nwAppnFwdLsCounters 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2
OBJECT IDENTIFIER    

nwAppnDistanceVector 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.1
OBJECT IDENTIFIER    

nwAppnLinkState 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2
OBJECT IDENTIFIER    

nwAppnIsr 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1
OBJECT IDENTIFIER    

nwAppnIsrSystem 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1
OBJECT IDENTIFIER    

nwAppnIsrInterfaces 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.2
OBJECT IDENTIFIER    

nwAppnIsrDatabase 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.3
OBJECT IDENTIFIER    

nwAppnIsrFilters 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.4
OBJECT IDENTIFIER    

nwAppnIsrConfig 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.1
OBJECT IDENTIFIER    

nwAppnIsrCounters 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.2
OBJECT IDENTIFIER    

nwAppnIsrIfConfig 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.2.1
OBJECT IDENTIFIER    

nwAppnIsrIfCounters 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.2.2
OBJECT IDENTIFIER    

nwAppnHostsSystem 1.3.6.1.4.1.52.4.2.2.2.3.5.2.6.1
OBJECT IDENTIFIER    

nwAppnHostsInterfaces 1.3.6.1.4.1.52.4.2.2.2.3.5.2.6.2
OBJECT IDENTIFIER    

nwAppnEventLogConfig 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.1
OBJECT IDENTIFIER    

nwAppnEventLogFilterTable 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2
OBJECT IDENTIFIER    

nwAppnEventLogTable 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3
OBJECT IDENTIFIER    

nwAppnMibRevText 1.3.6.1.4.1.52.4.2.2.2.3.5.1.1
Indicates the current revision level of the Cabletron APPN Router MIB in textual format.
OBJECT-TYPE    
  DisplayString  

nwAppnSysRouterId 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.1
Specifies the APPN Fully-Qualified Control Point name that is used to uniquely identify APPN Routing Services in an APPN network. The name format is NNNNNNNN.CCCCCCCC where NNNNNNNN is the network identifier and CCCCCCCC is the Control Point name. Valid characters to make up these two strings are uppercase letters A through Z, numerics 0 through 9, and the special characters $, @, and #. The first character of the string must NOT be numeric. Each string must be a maximum length of 8 characters with no embedded spaces and the strings are joined by a dot. nwAppnSysRouterId cannot be modified while APPN routing services is in any operational state other than DISABLED as reflected in nwAppnSysOperStatus. Otherwise, the request will be rejected.
OBJECT-TYPE    
  DisplayString Size(3..17)  

nwAppnSysNodeType 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.1
Indicates the node type supported by APPN Routing Services which is always of type Network Node.
OBJECT-TYPE    
  INTEGER networknode(1)  

nwAppnSysCpAlias 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.2
Specifies the Control Point alias name used by APPN Routing Services.
OBJECT-TYPE    
  DisplayString Size(1..8)  

nwAppnSysModeCosMap 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.3
Specifies whether mode to COS mapping is supported by APPN Routing Services.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

nwAppnSysMdsSupport 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.4
Specifies whether Management Services supports Multiple Domain Support and Management Services capabilities.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

nwAppnSysMaxLocates 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.6
Specifies maximum Number of locate requests that APPN Routing Services can concurrently process. Note: if nwAppnSysMaxLocates is set to a value too small, it will be internally increased to a higher value after APPN Routing Services has been successfully enabled. A subsequent GET operation on nwAppnSysMaxLocates will reflect this new value.
OBJECT-TYPE    
  INTEGER 1..65535  

nwAppnSysDirCacheSize 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.7
Specifies number of located resources maintained in the Directory Cache. Note: if nwAppnSysDirCacheSize is set to a value too small, it will be internally increased to a higher value after APPN routing services has been successfully enabled. A subsequent GET operation on nwAppnSysDirCacheSize will reflect this new value.
OBJECT-TYPE    
  INTEGER 1..65535  

nwAppnSysMaxDirEntries 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.8
Specifies maximum number of directory entries. If zero is selected, the number of entries is unlimited.
OBJECT-TYPE    
  INTEGER 0..65535  

nwAppnSysLocateTimeout 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.9
Specifies time in seconds before a network search will timeout. Zero indicates that the search has no timeout.
OBJECT-TYPE    
  INTEGER 0..65535  

nwAppnSysRegCds 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.10
Specifies whether the local or domain resources can be registered with the Central Directory Server.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

nwAppnSysMdsSendQSize 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.11
Specifies size of the MDS send alert Queue.
OBJECT-TYPE    
  INTEGER 1..65535  

nwAppnSysCosSize 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.12
Specifies maximum number of COS definitions maintained in the COS database weights cache. It determines the size of the COS Database weights cache. Note: if nwAppnSysCosSize is set to a value too small, it will be internally increased to a higher value after APPN Routing Services has been successfully enabled. A subsequent GET operation on nwAppnSysCosSize will reflect this new value.
OBJECT-TYPE    
  INTEGER 1..65535  

nwAppnSysTreeSize 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.13
Specifies the number of routes maintained in the Topology Database routing tree cache. Note: if nwAppnSysTreeSize is set to a value too small, it will be internally increased to a higher value after APPN Routing Services has been successfully enabled. A subsequent GET operation on nwAppnSysTreeSize will reflect this new value.
OBJECT-TYPE    
  INTEGER 1..65535  

nwAppnSysTreeUseLimit 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.14
Maximum number of times a cached tree will be used to compute a route before the tree is discarded and recomputed. This allows the APPN Routing Services to balance sessions among equal weight routes. A low value provides better load balancing at the expense of increased activation latency.
OBJECT-TYPE    
  INTEGER 1..65535  

nwAppnSysMaxTdmNodes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.15
Specifies maximum number of nodes that can be stored in the Topology Database. Zero means unlimited.
OBJECT-TYPE    
  INTEGER 0..65535  

nwAppnSysMaxTdmTGs 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.16
Specifies maximum number of transmission groups that can be stored in Topology Database. Zero means unlimited.
OBJECT-TYPE    
  INTEGER 0..65535  

nwAppnSysMaxIsrSessions 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.18
Specifies maximum number of intermediate routing sessions permitted by APPN Routing Services at one time. This must be a non-negative number.
OBJECT-TYPE    
  INTEGER 1..65535  

nwAppnSysIsrUpperThresh 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.19
The thresholds control the congestion status of APPN routing services. If the number of ISR sessions exceeds the upper threshold, congestion status changes from uncongested to congested. When this occurs, the status will not become uncongested until the the number of ISR sessions fall below the lower threshold. The lower threshold should be less than the upper threshold to prevent thrashing. The upper threshold should be lower than nwAppnSysMaxIsrSessions. This must be a non-negative number.
OBJECT-TYPE    
  INTEGER 1..65535  

nwAppnSysIsrLowerThresh 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.20
Specifes the number of ISR sessions at which congestion status will revert to uncongested. This must be a non-negative number. nwAppnSysIsrLowerThresh must be less than nwAppnSysIsrUpperThresh to prevent thrashing.
OBJECT-TYPE    
  INTEGER 1..65535  

nwAppnSysIsrMaxRuSize 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.21
Specifies maximum RU size supported for intermediate sessions. Note: the number provided will be rounded up to the next valid RU size if necessary after APPN Routing Services has been successfully enabled. A subsequent GET operation on nwAppnSysMaxLocates will reflect this new value.
OBJECT-TYPE    
  INTEGER 1..65535  

nwAppnSysIsrRcvPaceWind 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.22
Specifies suggested receive pacing window size for intermediate sessions. This value may be used as a fixed window size for fixed pacing, or as a tuning value for adaptive pacing.
OBJECT-TYPE    
  INTEGER 1..63  

nwAppnSysRtAddResist 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.23
Specifies a desirability factor for APPN Routing Services to perform intermediate session routing. 255 is least desirable and 0 is more desirable.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnSysStopType 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.24
Specifies the type of APPN Routing Services shutdown. Once specified, select disable from nwAppnSysAdminStatus. The shutdown choices are as follows: abort(1) All APPN Routing Services components are immediately stopped and resources released. To become active again, the APPN Routing Services must be enabled. immediate(2) APPN Routing Services immediately deactivates all links then performs abort(1) processing. quiesce(3) APPN Routing Services indicates to other APPN network nodes that it is quiesced. Session limits are reset on all modes, UNBINDs are issued on all endpoint sessions (CP-CP sessions last), and then immediate(2) processing is performed. quiesceIsr(4) Allows all intermediate sessions to end, then performs the quiesce(3) processing.
OBJECT-TYPE    
  INTEGER abort(1), immediate(2), quiesce(3), quiesceIsr(4)  

nwAppnSysBlockNum 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.25
This represents the 3 hexadecimal digit block number which precedes the 5 digit id number in the 8 digit node id used in XIDs and Alerts. The block number identifies the product type. Both the block number and id number combined, uniquely identify this instance of APPN Routing Services within the installation network.
OBJECT-TYPE    
  DisplayString Size(3)  

nwAppnSysIdNum 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.26
This represents the 5 hexadecimal digit id number which follows the 3 digit block number in the 8 digit node id used in XIDs and Alerts. The id number uniquely identifies this instance of APPN Routing Services within a product type indicated by the block number. Both the block number and id number combined, uniquely identify this instance of APPN Routing Services within the installation network.
OBJECT-TYPE    
  DisplayString Size(5)  

nwAppnSysLuTable 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.3.1
This table contains entries for LUs that are owned by adjacent LEN nodes. Defining or deleting an entry is equivalent to defining or deleting an entry in the directory database. To add an entry, set nwAppnSysLuControl to other. To delete an entry, set nwAppnSysLuControl to delete.
OBJECT-TYPE    
  SEQUENCE OF  
    NwAppnSysLuEntry

nwAppnSysLuEntry 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.3.1.1
Each entry defines an LU entry in the directory database. The fully qualified CP name and the name of the LU are the indexes into this table.
OBJECT-TYPE    
  NwAppnSysLuEntry  

nwAppnSysCpName 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.3.1.1.1
Specifies the fully qualified name of the Control Point containing the LU being defined. The format of this name is NNNNNNNN.CCCCCCCC where NNNNNNNN is the network identifier and CCCCCCCC is the LU or Control Point name. Valid characters to make up these two strings are uppercase letters A through Z, numerics 0 through 9 and the special charcters $, @, and #. The first character of the name must NOT be numeric. Each string must be a maximum length of 8 characters with no embedded spaces and the strings are joined by a dot. This CP name must appear as an Adjacent CP in a link station definition where the adjacent CP type is EN and CP-CP session support is NO.
OBJECT-TYPE    
  DisplayString Size(3..17)  

nwAppnSysLuName 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.3.1.1.2
Specifies the name of the LU being registered. The name format is LLLLLLLL where LLLLLLLL are the characters: uppercase letters A through Z, numerics 0 through 9, and the special characters $, @, and #. The first character of the name must NOT be numeric. The string must be a maximum length of 8 characters with no embedded spaces. Note that the nework identifier of the LU is taken from the fully qualified control point name of the adjacent LEN node (nwAppnSysCpName) which owns the LU.
OBJECT-TYPE    
  DisplayString Size(1..8)  

nwAppnSysLuControl 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.3.1.1.3
Set this object to delete to remove an entry.
OBJECT-TYPE    
  INTEGER other(1), delete(3)  

nwAppnSysAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.2.1
Sets the system-wide administrative state of APPN Routing Services. If enable(3) is selected, APPN Routing Services is activated. There are two cases: the very first activation, and activations subsequent to the successful first activation. Before activating APPN Routing Services the very first time, nwAppnSysRouterId in the System Configuration branch and all objects under nwAppnSysCfgLocalNode must be assigned a value. If not explicitly assigned, default values will be used for objects under nwAppnSysCfgLocalNode. After this first activation has completed successfully, all objects under nwAppnSysCfgLocalNode will be saved in non-volatile RAM and restored for the next node activation at power up time. After this subsequent power up, enable(3) may be selected without setting nwAppnSysRouterId or any objects under under nwAppnSysCfgLocalNode. Those values defined prior to the last power up or reset will be used. If disable(2) is selected, APPN Routing Services will become inactive in the manner specifed by nwAppnSysStopType. To modify objects under nwAppnSysCfgLocalNode, nwAppnSysAdminStatus must be disabled.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enabled(3)  

nwAppnSysOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.2.2
Indicates the current operating system-wide status of APPN Routing Services.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pendingDisable(4), pendingEnable(5)  

nwAppnSysAdminReset 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.2.3
Resets APPN Routing Services system-wide. Reset (2) forces a restart of APPN Routing Services without a graceful shutdown on any active router ports, without affecting any other routing services.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwAppnSysOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.2.4
Indicates the elapsed time, in hundredths of a second, that nwAppnOperStatus has been in its current state.
OBJECT-TYPE    
  TimeTicks  

nwAppnSysVersion 1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.2.5
Indicates the current revision level of APPN routing services in textual format.
OBJECT-TYPE    
  DisplayString  

nwAppnFwdCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.1
Sets the administrative state of the aggregate, system-wide, port Message Unit (MU) and byte counters. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwAppnFwdCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.2
Resets the aggregate, system-wide port Message Unit (MU) and byte counters. Reset (2) resets the aggregate counters to 0. nwAppnFwdCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwAppnFwdCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.3
Indicates the elapsed time, in hundredths of a second, that nwAppnFwdCtrAdminStatus has been in the current state.
OBJECT-TYPE    
  TimeTicks  

nwAppnFwdCtrInMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.4
Indicates the total number of Message Units (MU)s that have been received system-wide (for all ports) during nwAppnFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrOutMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.5
Indicates the total number of Message Units (MU)s that have been transmitted system-wide (for all ports) during nwAppnFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrFwdMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.6
Indicates the total number of Message Units (MU)s that have been forwarded system-wide (for all ports) during nwAppnFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrFilteredMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.7
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrDiscardMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.8
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrAddrErrMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.9
Indicates the total number of Message Units (MUs) that have been received system-wide (for all ports), during nwAppnFwdCtrOperationalTime, that contain an address error(s) in the SNA header.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrLenErrMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.10
Indicates the total number of Message Units (MUs) that have been received system-wide (for all ports), during nwAppnFwdCtrOperationalTime, that contain a length error.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrHdrErrMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.11
Indicates the total number of Message Units (MUs) that have been received system-wide (for all ports), during nwAppnFwdCtrOperationalTime, that contain an SNA header error other than an address or length error.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.12
Indicates number of bytes in Message Units (MUs) that have been received system-wide (for all ports), during nwAppnFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.13
Indicates the total number of bytes in Message Units (MUs) that have been forwarded system-wide (for all ports), during nwAppnFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrFwdBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.14
Indicates the total number of bytes in Message Units (MUs) that have been forwarded system-wide (for all ports), during nwAppnFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.15
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.16
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrHostInMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.17
Indicates the total number of Message Units (MUs) that have been delivered system-wide (for all ports), to local half sessions during nwAppnFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrHostOutMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.18
Indicates the total number of Message Units (MUs) that have been successfully sent from local half sessions system-wide (for all ports), to Path Control during nwAppnFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrHostDiscardMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.19
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrHostInBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.20
Indicates the total number of bytes in Message Units (MUs) that have been delivered system-wide (for all ports), to local half sessions during nwAppnFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrHostOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.21
Indicates the total number of bytes in Message Units (MUs) that have been successfully sent from local half sessions system-wide (for all ports), to Path Control during nwAppnFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwAppnFwdCtrHostDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.22
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfTable 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1
This table contains an entry for each router port which can be used by APPN Routing Services. This table is indexed by nwAppnFwdIfIndex, which indicates the value of MIB 2 ifindex which identifes the router port for which an entry exists. These port configuration entries will be provided automatically based on physical port configuration. Such entries cannot be deleted - only modified.
OBJECT-TYPE    
  SEQUENCE OF  
    NwAppnFwdIfEntry

nwAppnFwdIfEntry 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1
Each entry specifies the APPN Routing Services port configuration for the router port for which the entry exists.
OBJECT-TYPE    
  NwAppnFwdIfEntry  

nwAppnFwdIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.1
Indicates the value of MIB2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwAppnFwdIfAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.2
Sets the administrative state of an APPN Routing Services port for which the entry exists. enabled(3) causes the APPN Routing Services port to become active. disable(2) causes it to become inactive. There are various choices for the method by which the port can be disabled, which are enumerated by nwAppnExtIfStopType.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enabled(3)  

nwAppnFwdIfOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.3
Indicates the current operating condition of the APPN Routing Services port for which the entry exists.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pendingDisable(4), pendingEnable(5)  

nwAppnFwdIfOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwAppnFwdIfOperStatus has been in the current state.
OBJECT-TYPE    
  TimeTicks  

nwAppnFwdIfControl 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.5
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER other(1)  

nwAppnFwdIfMtu 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.6
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER  

nwAppnFwdIfForwarding 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.7
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwAppnFwdIfFrameType 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.8
Specifies the framing type for the APPN Routing Services port for which the entry exists.
OBJECT-TYPE    
  INTEGER other(1), ethernet(2), i8022(4), sync(8)  

nwAppnFwdIfAclIdentifier 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.9
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER  

nwAppnFwdIfAclStatus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.10
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwAppnFwdIfCacheControl 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.11
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

nwAppnFwdIfCacheEntries 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.12
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCacheHits 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.13
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCacheMisses 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.14
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  Counter  

nwAppnExtensionTable 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2
This table contains additional APPN definitions for each physical port. Entries cannot be added to or deleted from this table. With the exception of nwAppnExtIfStopType, objects in this table may only be modified when nwAppnFwdIfAdminStatus is disabled. Note: if APPN Routing Services is not active, no entries will exist for this table.
OBJECT-TYPE    
  SEQUENCE OF  
    NwAppnExtEntry

nwAppnExtEntry 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1
Each entry specifies additional APPN configuration parameters for the port for which this entry exists.
OBJECT-TYPE    
  NwAppnExtEntry  

nwAppnExtIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.1
Specifies the primary index into the APPN port extension table. This number corresponds to the index into the nwAppnFwdIfTable.
OBJECT-TYPE    
  INTEGER  

nwAppnExtIfPortName 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.2
Specifies the user friendly name for this port.
OBJECT-TYPE    
  DisplayString Size(1..8)  

nwAppnExtIfPortType 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.4
Specifies the type of line used by the port. The value corresponds to one of the following: nonswitched(1), switched(2), or satf(3).
OBJECT-TYPE    
  INTEGER nonswitched(1), switched(2), satf(3)  

nwAppnExtIfDlcType 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.5
Specifies the type of DLC using the port.
OBJECT-TYPE    
  INTEGER llc2(1), sdlc(2), x25(3)  

nwAppnExtIfMaxRBtuSize 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.6
Specifies the maximum Message Unit (MU) size that can be received.
OBJECT-TYPE    
  INTEGER 99..65535  

nwAppnExtIfTotLsActLim 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.7
Specifies the total number of links that can be active on this port. If nwAppnExtIfPortType = nonswitched(1) and nwAppnExtIfLocalLsRole = negotiable(1), or secondary(3), then this value must be set to 1.
OBJECT-TYPE    
  INTEGER 1..256  

nwAppnExtIfInbLsActLim 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.8
Specifies the total number of inbound links that can be active on this port. If nwAppnExtIfPortType = nonswitched(1) and nwAppnExtIfLocalLsRole = negotiable(1) or primary(2), then this value must be set to 0.
OBJECT-TYPE    
  INTEGER 0..256  

nwAppnExtIfOutbLsActLim 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.9
Specifies the total number of outbound links that can be active on this port. If nwAppnExtIfPortType = nonswitched(1) and nwAppnExtIfLocalLsRole = negotiable(1), then this value must be set to 0. If nwAppnExtIfLocalLsRole = primary(2), then this value must be set the same as nwAppnExtIfTotLsActLim.
OBJECT-TYPE    
  INTEGER 0..256  

nwAppnExtIfLocalLsRole 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.10
Specifies the link station role - primary, secondary, or negotiable. For nwAppnExtIfPortType = satf(3), the link station role must be negotiable(1).
OBJECT-TYPE    
  INTEGER negotiable(1), primary(2), secondary(3)  

nwAppnExtIfActXidXchgLimit 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.11
Specifies the total number of activation XIDs that may be exchanged.
OBJECT-TYPE    
  INTEGER 0..65535  

nwAppnExtIfNonActXidXchgLimit 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.12
Specifies the total number of non-activation XIDs that may be exchanged.
OBJECT-TYPE    
  INTEGER 0..65535  

nwAppnExtIfLsXmitRcvCap 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.13
Specifies the link station's transmit/receive capability.
OBJECT-TYPE    
  INTEGER twowaysimultaneous(1), twowayalternating(2)  

nwAppnExtIfMaxIfrmRcvd 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.14
Specifies the maximum number of I-frames received before an acknowledgment is sent to the sender.
OBJECT-TYPE    
  INTEGER 1..127  

nwAppnExtIfDfltTargetPacing 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.15
Specifies the pacing window size for BINDs on this transmission group.
OBJECT-TYPE    
  INTEGER 1..32767  

nwAppnExtIfDfltMaxSBtuSize 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.16
Specifies the maximum Message Unit (MU) size which can be sent.
OBJECT-TYPE    
  INTEGER 99..65535  

nwAppnExtIfDfltEffectCap 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.17
Specifies the default maximum kilo bits per second rate (line speed) for all links on this port.
OBJECT-TYPE    
  INTEGER 0..603979776  

nwAppnExtIfDfltConnectCost 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.18
Specifies the default cost per connect time for all link stations on this port. 0 is the lowest cost and 255 is the largest cost.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnExtIfDfltByteCost 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.19
Specifies the default Cost per Byte for link stations. 0 is the lowest cost and 255 is the largest cost.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnExtIfDfltSecurity 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.20
Specify one of the following security selections: non-secure - specifies no security. public switched - data flows over a public switched network. underground cable - data transmitted over a secure underground cable. secure conduit - line is secure conduit that is not guarded. guarded conduit - conduit that is protected against physical tapping. encrypted - encryption over the line. guarded radiation - line is proected against physical and radiation tapping.
OBJECT-TYPE    
  INTEGER nonsecure(1), publicSwitchNw(32), undergroundCable(64), secureConduit(96), guardedConduit(128), encrypted(160), guardedRadiation(192)  

nwAppnExtIfDfltPropDelay 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.21
Specifies the propagation delay which represents the relative time it takes for a signal to travel the length of the link in microseconds, with some of the more common default values enumerated. The default times in parentheses are in microseconds. These default values fall into the following ranges: minimum - no propagation delay negligible, lan - less than 480 microseconds terrestrial, telephone - between 480 and 49,512 microseconds packetswitched - between 49,512 and 245,760 microseconds long, satellite - more than 245760 microseconds. maximum - the maximum propagation delay.
OBJECT-TYPE    
  INTEGER minimum(0), negligible(384), terrestrial(9216), packetswitched(147456), long(294912), maximum(2013265920)  

nwAppnExtIfDfltUsrDef1 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.22
Specifies user defined parameter 1.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnExtIfDfltUsrDef2 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.23
Specifies user defined parameter 2.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnExtIfDfltUsrDef3 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.24
Specifies user defined parameter 3.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnExtIfStopType 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.25
Specifies the type of shutdown for APPN Routing Services on the port. Once set, nwAppnFwdIfAdminStatus may be set to disable. The disable choices are as follows: immediate(1) causes the link stations belonging to the physical port to be disabled immediately without flushing pending messages and without initiating an orderly disconnect sequence. orderly(2) causes pending messages in link stations to be flushed, followed by an orderly disconnect sequence. The link station is then disabled.
OBJECT-TYPE    
  INTEGER immediate(1), orderly(2)  

nwAppnExtIfCpCpSupp 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.26
Specifies whether CP-CP sessions are permitted on dynamic links generated on this port.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

nwAppnExtIfLimitedRsrc 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.27
Specifies whether dynamic links generated on this port are a limited resource. A limited resource link will be deactivated when there are no sessions using the link.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

nwAppnExtIfAddress 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.28
Specifies the physical address of this port depending on the media type. For token ring or ethernet ports, the information is the 6 byte MAC address which starts in byte 1 and ends in byte 6. For token ring ports the MAC address must be specified in non- canonical format. For ethernet ports the MAC address must be specified in canonical format. For frame relay ports, there is no associated address, i.e., it will be a zero length octet string.
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

nwAppnExtIfSsap 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.29
For token ring or ethernet ports specifies the Source SAP Address of this port.
OBJECT-TYPE    
  OCTET STRING Size(1)  

nwAppnIfCnPortTable 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.1
This table contains definitions for the Connection Network port table which defines which local ports can access a connection network. To add a row to the table, nwAppnIfCnPtFqName and nwAppnIfCnPtName are required entries. To delete a row, set the control field to delete. Adding the first row for a connection network implicitly creates the connection network and deleting the last remaining row for a connection network implicitly removes the connection network.
OBJECT-TYPE    
  SEQUENCE OF  
    NwAppnIfCnPortEntry

nwAppnIfCnPortEntry 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.1.1
Specifies the APPN Connection Network port definitions.
OBJECT-TYPE    
  NwAppnIfCnPortEntry  

nwAppnIfCnPtFqName 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.1.1.1
Specifies the fully-qualified Name of the Virtual Routing Node. The name format is NNNNNNNN.CCCCCCCC where NNNNNNNN is the network identifier and CCCCCCCC is the Control Point name. Valid characters to make up these two strings are uppercase letters A through Z, numerics 0 through 9, and the special characters $, @, and #. The first character of the name must NOT be numeric. Each string must be a maximum length of 8 characters with no embedded spaces and the strings are joined by a dot.
OBJECT-TYPE    
  DisplayString Size(3..17)  

nwAppnIfCnPtName 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.1.1.2
Specifies one of the ports which can access this Connection Network.
OBJECT-TYPE    
  DisplayString Size(1..8)  

nwAppnIfCnPtControl 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.1.1.3
Set this object to delete to delete this port from this Connection Network.
OBJECT-TYPE    
  INTEGER other(1), delete(3)  

nwAppnIfCnTgCharTable 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2
This table contains the APPN definitions for a Connection Network's transmission group characteristics. Rows may be neither added nor deleted, only modified. Rows are added/deleted implicitly through CnPortTable.
OBJECT-TYPE    
  SEQUENCE OF  
    NwAppnIfCnTgCharEntry

nwAppnIfCnTgCharEntry 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1
Specifies the APPN transmission group characteristics for the Connection Network.
OBJECT-TYPE    
  NwAppnIfCnTgCharEntry  

nwAppnIfCnTgFqName 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.1
Specifies the fully-qualified Name of the Virtual Routing Node. The name format is NNNNNNNN.CCCCCCCC where NNNNNNNN is the network identifier and CCCCCCCC is the Control Point name. Valid characters to make up these two strings are uppercase letters A through Z, numerics 0 through 9, and the special characters #, $, and @. The first character of the name must NOT be numeric. Each string must be a maximum length of 8 characters with no embedded spaces and the strings are joined by a dot.
OBJECT-TYPE    
  DisplayString Size(3..17)  

nwAppnIfCnTgEffectCap 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.2
Specifies the maximum kilo bits per second rate (link speed) for the connection network.
OBJECT-TYPE    
  INTEGER 0..603979776  

nwAppnIfCnTgConnectCost 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.3
Specifies the cost per connect time for the Connection Network. 0 is the lowest cost and 255 is the largest cost.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnIfCnTgByteCost 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.4
Specifies the cost per byte for the Connection Network. 0 is the lowest cost and 255 is the largest cost.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnIfCnTgSecurity 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.5
For the Connection Network, specify one of the following security selections: non-secure - specifies no security. public switched - data flows over a public switched network. underground cable - data transmitted over a secure underground cable. secure conduit - line is secure conduit that is not guarded. guarded conduit - conduit that is protected against physical tapping. encrypted - encryption over the line. guarded radiation - line is proected against physical and radiation tapping.
OBJECT-TYPE    
  INTEGER nonsecure(1), publicSwitchNw(32), undergroundCable(64), secureConduit(96), guardedConduit(128), encrypted(160), guardedRadiation(192)  

nwAppnIfCnTgPropDelay 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.6
Specifies the propagation delay which represents the time it takes for a signal to travel the length of the link in microseconds, with some of the more common default values enumerated. The default times in parentheses are in microseconds. These default values fall into the following ranges: minimum - no propagation delay negligible, lan - less than 480 microseconds terrestrial, telephone - between 480 and 49,512 microseconds packetswitched - between 49,512 and 245,760 microseconds long, satellite - more than 245760 microseconds. maximum - the maximum propagation delay.
OBJECT-TYPE    
  INTEGER minimum(0), negligible(384), terrestrial(9216), packetswitched(147456), long(294912), maximum(2013265920)  

nwAppnIfCnTgUsrDef1 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.7
Specifies user defined parameter 1.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnIfCnTgUsrDef2 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.8
Specifies user defined parameter 2.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnIfCnTgUsrDef3 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.9
Specifies user defined parameter 3.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnFwdIfCtrTable 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1
This table contains the Message Unit (MU) and byte counters for each port configured and enabled for APPN Routing Services.
OBJECT-TYPE    
  SEQUENCE OF  
    NwAppnFwdIfCtrEntry

nwAppnFwdIfCtrEntry 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1
Each entry indicates Message Units (MU) and byte counts on the router port for which this entry exists.
OBJECT-TYPE    
  NwAppnFwdIfCtrEntry  

nwAppnFwdIfCtrIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.1
Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists. This is the primary index into the APPN per-port counter table.
OBJECT-TYPE    
  INTEGER  

nwAppnFwdIfCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.2
Sets the administrative state of the per-port Message Unit (MU) and byte counters on the router port for which the entry exists. enabled(3) causes these counters to become active. disabled(2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwAppnFwdIfCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.3
Resets the per-port Message Unit (MU) and byte counters on the router port for which this entry exists. reset (2) resets the counters to 0. nwAppnFwdIfCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwAppnFwdIfCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.4
Indicates the amount of time in hundreths of a second that the per-port Message Unit (MU) and byte counters have been active on the APPN routing services port for which this entry exists.
OBJECT-TYPE    
  TimeTicks  

nwAppnFwdIfCtrInMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.5
Indicates the total number of Message Units (MU)s that have been received, during nwAppnFwdIfCtrOperationaltime on the router port for which this entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrOutMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.6
Indicates the total number of Message Units (MU)s that have been transmitted, during nwAppnFwdIfCtrOperationalTime, on the router port for which this entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrFwdMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.7
Indicates the total number of Message Units (MU)s that have been forwarded during nwAppnFwdIfCtrOperationalTime on the router port for which this entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrFilteredMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.8
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrDiscardMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.9
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrAddrErrMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.10
Indicates the total number of Message Units (MUs) that contain an address error in the SNA header that have been received during nwAppnFwdIfCtrOperationalTime on the router port for which this entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrLenErrMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.11
Indicates the total number of Message Units (MUs) that contain a length error that have been received during nwAppnFwdIfCtrOperationalTime on the router port for which this entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrHdrErrMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.12
Indicates the total number of Message Units (MUs) that contain a header error other than an address or length error that have been received during nwAppnFwdIfCtrOperationalTime on the router port for which this entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.13
Indicates the total number of bytes in the Message Units (MU)s that have been received, during nwAppnFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.14
Indicates the total number of bytes in the Message Units (MU)s that have been transmitted, during nwAppnFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrFwdBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.15
Indicates the total number of bytes in Message Units (MU)s that have been forwarded during nwAppnFwdIfCtrOperationalTime on the router port for which this entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.16
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.17
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrHostInMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.18
Indicates the total number of Message Units (MUs) that have been delivered to local half sessions during nwAppnFwdIfCtrOperationalTime on the router port for which this entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrHostOutMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.19
Indicates the total number of Message Units (MUs) that have been successfully sent from local half sessions to Path Control during nwAppnFwdIfCtrOperationalTime on the router port for which this entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrHostDiscardMus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.20
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrHostInBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.21
Indicates the total number of bytes in Message Units (MUs) that have been delivered to local half sessions during nwAppnFwdIfCtrOperationalTime on the router port for which this entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrHostOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.22
Indicates the total number of bytes in Message Units (MUs) that have been successfully sent from local half sessions to Path Control during nwAppnFwdIfCtrOperationalTime on the router port for which this entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdIfCtrHostDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.23
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsTable 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1
This table contains the configuration and management information for links to adjacent link stations. This table is indexed by nwAppnFwdLsName. Operations which apply are add, delete, modify, enable, and disable. To add a row to the table, the required fields in the row must be provided. The required fields are nwAppnFwdLsPortName and nwAppnFwdLsDestAddr. All other fields which are not provided will be defaulted. To enable a link select enable(3) from nwAppnFwdLsAdminStatus. To delete a row, set nwAppnFwdLsControl to delete(3). To disable a link set nwAppnFwdLsStopType and then select disable(2) in nwAppnFwdLsAdminStatus. If nwAppnFwdLsStopType is not selected, the link is disabled in an orderly fashion.
OBJECT-TYPE    
  SEQUENCE OF  
    NwAppnFwdLsEntry

nwAppnFwdLsEntry 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1
Specifies the configuration for a link to an adjacent link station for which the entry exists.
OBJECT-TYPE    
  NwAppnFwdLsEntry  

nwAppnFwdLsName 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.1
Specifies the primary index to the adjacent link station table (nwAppnFwdLsTable).
OBJECT-TYPE    
  DisplayString Size(1..8)  

nwAppnFwdLsAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.2
Sets the administrative state of a link to an adjacent link station. enabled(3) causes the link to become established. disable(2) causes the link to terminate. There are various severities of disabling a link which are selected via the leaf node nwAppnFwdLsStopType described further within this branch.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

nwAppnFwdLsOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.3
Specifies the current operating status of the link for which this entry exists.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pendingDisable(4), pendingEnable(5)  

nwAppnFwdLsOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.4
Specifies the elapsed time, in hundredths of a second, that nwAppnFwdLsAdminStatus has been either enabled or DISABLED. If the operational state is pending-disable, nwAppnFwdLsOperationalTime indicates the amount of time since the state was enabled. If the operational state is pending-enable, nwAppnFwdLsOperationalTime indicates the amount of time since the state was DISABLED.
OBJECT-TYPE    
  TimeTicks  

nwAppnFwdLsControl 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.5
Set this object to delete in order to delete the entry.
OBJECT-TYPE    
  INTEGER other(1), delete(3)  

nwAppnFwdLsPortName 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.6
This link station port name corresponds to the port name index into the the nwAppnExtensionTable which describes the router port on which the adjacent link station is defined.
OBJECT-TYPE    
  DisplayString Size(1..8)  

nwAppnFwdLsAdjCpName 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.7
Specifies the fully-qualified, 17 byte long, adjacent Control Point name. The name format is NNNNNNNN.CCCCCCCC where NNNNNNNN is the network identifier and CCCCCCCC is the Control Point name. Valid characters to make up these two strings are uppercase letters A through Z, numerics 0 through 9, and the special characters $, # and @. The first character of the name must NOT be numeric. Each string must be a maximum length of 8 characters with no embedded spaces and the strings are joined by a dot.
OBJECT-TYPE    
  DisplayString Size(3..17)  

nwAppnFwdLsAdjCpType 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.8
Specifies the adjacent node type. The following values are valid: endnode(1), networknode(2). endnode(1) includes both End Node and LEN node types.
OBJECT-TYPE    
  INTEGER endnode(1), networknode(2)  

nwAppnFwdLsAutoActSupport 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.10
Specifies whether the link is automatically enabled when a session is activated over the link. It is an error to set this to yes(1) when nwAppnFwdLsCpCpSessSupp is set to yes(1).
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

nwAppnFwdLsLimitedRsrc 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.11
Specifies whether this link is to be deactivated when there are no sessions using the link. If nwAppnFwdLsCpCpSessSupp is yes, however, the link will not be deactivated if CP-CP sessions are terminated. Note also that a link over a non-switched port cannot be configured as a limited resource.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

nwAppnFwdLsSscpSession 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.12
Requests a host system to initiate sessions between its SSCP and dependent LUs within APPN Routing Services. If set to yes, then nwAppnFwdLsPuName is required. Note: once this parameter is set along with other link station parameters associated with a link station definition, it cannot be modified. In order to change it, the link station definition itself must be deleted and then redefined with the new parameter.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

nwAppnFwdLsPuName 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.13
Specifies the name of the local PU if nwAppnFwdLsSscpSession is set to yes. Valid characters are uppercase A through Z and numerics 0 through 9. The name must start with an alphabetic character. Note: once this parameter is set along with other link station parameters associated with a link station definition, it cannot be modified. In order to change it, the link station definition itself must be deleted and then redefined with the new parameter.
OBJECT-TYPE    
  DisplayString Size(1..8)  

nwAppnFwdLsBackLvlLenEN 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.14
Specifies whether or not the adjacent node is a back level LEN Node. If so, specify the type of back level LEN node as follows: xid3(2) - supports XID-3 protocols, but does not include Network Name control vector in the XID. xid0(3) - Supports XID-0 protocols. Not valid if nwAppnExtIfLocalLsRole is negotiable(1). noxid(4) - Does not support XID protocols. Valid only if nwAppnExtIfPortType is nonswitched(1) and not valid if nwAppnExtIfLocalLsRole is negotiable(1). If not no(1), then nwAppnFwdLsAdjCpName and nwAppnFwdLsIdNum must be specified.
OBJECT-TYPE    
  INTEGER no(1), xid3(2), xid0(3), noxid(4)  

nwAppnFwdLsCpCpSessSupp 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.16
Specifies whether this link supports CP to CP sessions.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

nwAppnFwdLsEffectCap 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.17
Specifies th maximum kilo bits per second rate (link speed) for the link.
OBJECT-TYPE    
  INTEGER 0..603979776  

nwAppnFwdLsConnectCost 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.18
Specifies the cost per connect time for the link. Zero is the lowest cost and 255 is the largest cost.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnFwdLsByteCost 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.19
Specifies the cost per Byte for the link. Zero is the lowest cost and 255 is the largest cost.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnFwdLsSecurity 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.20
Security selections available for the link are as follows: non-secure - specifies no security. public switched - data flows over a public switched network. underground cable - data transmitted over a secure underground cable. secure conduit - line is secure conduit that is not guarded. guarded conduit - conduit that is protected against physical tapping. encrypted - encryption over the line. guarded radiation - line is proected against physical and radiation tapping.
OBJECT-TYPE    
  INTEGER nonsecure(1), publicSwitchNw(32), undergroundCable(64), secureConduit(96), guardedConduit(128), encrypted(160), guardedRadiation(192)  

nwAppnFwdLsPropDelay 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.21
Specifies the propagation delay which represents the relative time it takes for a signal to travel the length of the link in microseconds, with some of the more common default values enumerated. The default times in parentheses are in microseconds. These default values fall into the following ranges: minimum - no propagation delay negligible, lan - less than 480 microseconds terrestrial, telephone - between 480 and 49,512 microseconds packetswitched - between 49,512 and 245,760 microseconds long, satellite - more than 245760 microseconds. maximum - the maximum propagation delay.
OBJECT-TYPE    
  INTEGER minimum(0), negligible(384), terrestrial(9216), packetswitched(147456), long(294912), maximum(2013265920)  

nwAppnFwdLsUsrDef1 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.22
Specifies user defined parameter 1.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnFwdLsUsrDef2 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.23
Specifies user defined parameter 2.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnFwdLsUsrDef3 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.24
Specifies user defined parameter 3.
OBJECT-TYPE    
  INTEGER 0..255  

nwAppnFwdLsTrgtPacingCount 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.25
Species the desired pacing window size for BINDs on this transmission group. The number is a value between 0 and 32767 and is significant only when fixed bind pacing is being used.
OBJECT-TYPE    
  INTEGER 0..32767  

nwAppnFwdLsMaxSendBtu 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.26
Specifies maximum Message Unit (MU) size that can be sent.
OBJECT-TYPE    
  INTEGER 99..65535  

nwAppnFwdLsNumActiveSession 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.27
Specifies total number of active sessions on this link. This includes both end point sessions and intermediate sessions.
OBJECT-TYPE    
  INTEGER  

nwAppnFwdLsdynamicLs 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.28
Specifies whether this link station was dynamically allocated (yes(1)) or whether the link station was defined by the user (no(2)).
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

nwAppnFwdLsStopType 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.29
Specifies the type of shutdown for a link. Once selected, set disable in nwAppnFwdIfAdminStatus. The shutdown choices are as follows: immediate(1) causes the link station to disconnect immediately without flushing remaining Message Unit (MU)s. orderly(2) causes the link station to disconnect after successfully flushing remaining Message Unit (MU)s.
OBJECT-TYPE    
  INTEGER immediate(1), orderly(2)  

nwAppnFwdLsPortNbr 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.30
This link station port number corresponds to the index into the nwAppnFwdIfTable and the nwAppnExtensionTable, which together describe the port used by APPN Routing Services.
OBJECT-TYPE    
  INTEGER  

nwAppnFwdLsDestAddr 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.31
Specifies the destination address of the adjacent link station depending on the media type. For token ring or ethernet ports, the information is the 6 byte Destination MAC Address which starts in byte 1 and ends in byte 6. For token ring ports, the MAC address must be specified in non-canonical format. For ethernet ports the MAC address must be specified in canonical format. For frame relay, the address is a non-null terminated string which is the ascii representation of the DLCI.
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

nwAppnFwdLsDsap 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.32
For a token ring or ethernet network, specifies the destination SAP address associated with the adjacent link station.
OBJECT-TYPE    
  OCTET STRING Size(1)  

nwAppnFwdLsBlockNum 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.33
This represents the 3 hexadecimal digit block number which precedes the 5 digit id number in the 8 digit node id of the adjacent node. The node id is used in XIDs and Alerts. The block number identifies the product type. Both the block number and id number combined, uniquely identify the adjacent node within the installation network.
OBJECT-TYPE    
  DisplayString Size(3)  

nwAppnFwdLsIdNum 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.34
This represents the 5 hexadecimal digit id number which follows the 3 digit block number in the 8 digit node id of the adjacent node. The node id is used in XIDs and Alerts. The id number uniquely identifies the adjacent node within a product type indicated by its block number. Both the block number and id number combined, uniquely identify the adjacent node within the installation network.
OBJECT-TYPE    
  DisplayString Size(5)  

nwAppnFwdLsCtrTable 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1
This table contains the Basic Link Unit (BLU) and byte counters for each configured adjacent link station.
OBJECT-TYPE    
  SEQUENCE OF  
    NwAppnFwdLsCtrEntry

nwAppnFwdLsCtrEntry 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1
Each entry indicates the Basic Link Unit (BLU) and byte count for the configured adjacent link station for which the entry exists.
OBJECT-TYPE    
  NwAppnFwdLsCtrEntry  

nwAppnFwdLsCtrLsName 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.1
Specifies the primary index into the link station counter table. This index is the link station name.
OBJECT-TYPE    
  DisplayString Size(1..8)  

nwAppnFwdLsCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.2
Sets the administrative state of the Basic Link Unit (BLU) and byte counters on the link for which this entry exists. enabled(3) causes these counters to reset and become active. disabled(2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwAppnFwdLsCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.3
Resets the Basic Link Unit (BLU) and byte counters on the link for which this entry exists. reset(2) resets the counters to 0. nwAppnFwdLsCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwAppnFwdLsCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.4
Specifies the amount of time in hundreths of a second that the Basic Link Unit (BLU) and byte counters have been active on the link for which this entry exists.
OBJECT-TYPE    
  TimeTicks  

nwAppnFwdLsCtrInBlus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.5
Specifies the total number of Basic Link Unit (BLU)s that have been received, during nwAppnFwdLsCtrOperationaltime, on the link for which this entry exists. This includes both information (I-frame) and XID BLUs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrOutBlus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.6
Specifies the total number of Basic Link Unit (BLU)s that have been transmitted, during nwAppnFwdLsCtrOperationalTime, on the link for which this entry exists. This includes both information (I-frame) and XID BLUs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrFwdBlus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.7
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrFilteredBlus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.8
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrDiscardBlus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.9
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrAddrErrBlus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.10
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrLenErrBlus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.11
Specifies the total number of received Basic Link Unit (BLU)s during nwAppnFwdLsCtrOperationalTime which have invalid DLC headers on the link for which this entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrHdrErrBlus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.12
Specifies the total number of received Basic Link Unit (BLU)s during nwAppnFwdLsCtrOperationalTime which have length errors on the link for which this entry exists.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.13
Specifies the total number of bytes that have been received, during nwAppnFwdLsCtrOperationalTime, on the link for which the entry exists. This includes bytes contained in information (I-frames) and XID BLUs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.14
Specifies the total number of bytes that have been transmitted, during nwAppnFwdLsCtrOperationalTime, on the link for which the entry exists. This includes bytes contained in information (I-frames) and XID BLUs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrFwdBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.15
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.16
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.17
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrHostInBlus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.18
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrHostOutBlus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.19
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrHostDiscardBlus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.20
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrHostInBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.21
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrHostOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.22
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnFwdLsCtrHostDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.23
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  Counter  

nwAppnIsrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.1.1
Intermediate Session Routing cannot be turned on and off. Any modifications to this leaf will have no affect.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

nwAppnIsrOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.1.2
Specifies the current operating condition of the ISR routing protocol, system-wide.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pendingDisable(4), pendingEnable(5)  

nwAppnIsrAdminReset 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.1.3
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs.
OBJECT-TYPE    
  INTEGER other(1)  

nwAppnIsrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwAppnOperStatus has been in its current state.
OBJECT-TYPE    
  TimeTicks  

nwAppnIsrVersion 1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.1.5
Indicates the current revision level of the ISR firmware in textual format. This is the same version number as that of APPN Routing Services firmware, nwAppnSysVersion.
OBJECT-TYPE    
  DisplayString  

nwAppnEventAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.1.1
Set the administrative state of APPN Routing Services event logging. enabled(3) causes the event log to become active. disabled(2) causes the event log to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwAppnEventMaxEntries 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.1.2
Sets the maximum number of entries allowed in the event log table. When the number of entries reaches the value of nwAppnEventMaxEntries the first (oldest) entry is deleted to allow a new entry to be added.
OBJECT-TYPE    
  INTEGER  

nwAppnEventTraceAll 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.1.3
enabled(3) allows logging of all event types on all ports. disabled(2) causes the filter table to specify which events to log.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwAppnEventFilterTable 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1
This table contains descriptions of how to filter log entries.
OBJECT-TYPE    
  SEQUENCE OF  
    NwAppnEventFilterEntry

nwAppnEventFilterEntry 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1
Each entry specifies the filter for log entries. The instance nwAppnEventProtocol refers to the instance used in the nwRtgProtocolTable and nwComponentTable specified by the ctrouter-mib.txt.
OBJECT-TYPE    
  NwAppnEventFilterEntry  

nwAppnEventFltrProtocol 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1.1
Selects the protocol to log events from.
OBJECT-TYPE    
  INTEGER  

nwAppnEventFltrIfNum 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1.2
Specifies the APPN Routing Services port on which to log events.
OBJECT-TYPE    
  INTEGER  

nwAppnEventFltrControl 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1.3
Setting this field to delete will allow entries to be removed from the table. This is done by adding new entries with instance fields that match the entry to be removed from the table. The new entry being added must have this control field set to delete in order for the matching entry already in the table to be deleted. Setting this field to add will add the entry to the table.
OBJECT-TYPE    
  INTEGER other(1), delete(2), add(3)  

nwAppnEventFltrType 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1.4
This bit field mask filter will allow only events of certain types to be logged. By default all types will be logged. Clearing event types from this field will cause those types not to be logged. Adding event types to this field will enable those types to be logged.
OBJECT-TYPE    
  INTEGER misc(1), timer(2), rcv(4), xmit(8), event(16), error(32)  

nwAppnEventFltrSeverity 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1.5
This filter controls the amount of logging by ignoring events of lower priority than that specified by the filter value. Specifying highest(1) causes all events except those of highest severity to be ignored. Specifying highmed(2) causes lowest severity events to be ignored. Specifying highlow(3) causes all events to be logged. highmed(2) is the default setting.
OBJECT-TYPE    
  INTEGER highest(1), highmed(2), highlow(3)  

nwAppnEventFltrAction 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1.6
This field specifies how the events are to be logged. Specifying log(1) stores the events in the event log table (defined below). Specifying trap(2) sends events out through the trap mechanism. Specifying logTrap(3) does both.
OBJECT-TYPE    
  INTEGER log(1), trap(2), logTrap(3)  

nwAppnEventTable 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1
This table contains all events that have been logged.
OBJECT-TYPE    
  SEQUENCE OF  
    NwAppnEventEntry

nwAppnEventEntry 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1
Each entry specifies events that have been logged.
OBJECT-TYPE    
  NwAppnEventEntry  

nwAppnEventNumber 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.1
This ordinal number uniquely identifies events.
OBJECT-TYPE    
  INTEGER  

nwAppnEventTime 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.2
This number specifies when the event was logged.
OBJECT-TYPE    
  TimeTicks  

nwAppnEventType 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.3
Specifies type of event logged.
OBJECT-TYPE    
  INTEGER misc(1), timer(2), rcv(4), xmit(8), event(16), diags(32), error(64)  

nwAppnEventSeverity 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.4
Specifies the severity of the event logged.
OBJECT-TYPE    
  INTEGER highest(1), highmed(2), highlow(3)  

nwAppnEventProtocol 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.5
Specifies the protocol where the event occured.
OBJECT-TYPE    
  INTEGER  

nwAppnEventIfNum 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.6
Specifies the APPN Routing Services port the event occurred on.
OBJECT-TYPE    
  INTEGER  

nwAppnEventTextString 1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.7
Specifies the actual text string to be logged.
OBJECT-TYPE    
  OCTET STRING