CPQSASSWITCH-MIB

File: CPQSASSWITCH-MIB.mib (16306 bytes)

Imported modules

CPQHOST-MIB RFC1155-SMI RFC1213-MIB
RFC-1212 RFC-1215 CPQSINFO-MIB
CPQIDA-MIB CPQSTSYS-MIB

Imported symbols

compaq enterprises Counter
Gauge DisplayString OBJECT-TYPE
TRAP-TYPE sysName sysLocation
cpqHoTrapFlags cpqSiProductName cpqSiSysProductId
cpqSiSysSerialNum cpqDaPhyDrvStatus cpqDaPhyDrvCntlrIndex
cpqDaPhyDrvIndex cpqDaPhyDrvLocationString cpqDaPhyDrvType
cpqDaPhyDrvModel cpqDaPhyDrvFWRev cpqDaPhyDrvSerialNum
cpqDaPhyDrvBoxOnConnector cpqSsBoxCntlrHwLocation cpqSsBoxCntlrIndex
cpqSsBoxBusIndex cpqSsBoxVendor cpqSsBoxModel
cpqSsBoxSerialNumber cpqSsBoxCondition cpqSsBoxLocationString

Defined Values

cpqSasSwitch 1.3.6.1.4.1.232.25
OBJECT IDENTIFIER    

cpqSasSwitchMibRev 1.3.6.1.4.1.232.25.1
OBJECT IDENTIFIER    

cpqSasSwitchComponent 1.3.6.1.4.1.232.25.2
OBJECT IDENTIFIER    

cpqSasSwitchInterface 1.3.6.1.4.1.232.25.2.1
OBJECT IDENTIFIER    

cpqSasSwitchHw 1.3.6.1.4.1.232.25.2.2
OBJECT IDENTIFIER    

cpqSasSwitchOsCommon 1.3.6.1.4.1.232.25.2.1.4
OBJECT IDENTIFIER    

cpqSasSwitchHwType 1.3.6.1.4.1.232.25.2.2.1
OBJECT IDENTIFIER    

cpqSasSwitchMibRevMajor 1.3.6.1.4.1.232.25.1.1
The Major Revision level. A change in the major revision level represents a major change in the architecture of the MIB. A change in the major revision level may indicate a significant change in the information supported and/or the meaning of the supported information, correct interpretation of data may require a MIB document with the same major revision level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

cpqSasSwitchMibRevMinor 1.3.6.1.4.1.232.25.1.2
The Minor Revision level. A change in the minor revision level may represent some minor additional support, no changes to any pre-existing information has occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

cpqSasSwitchMibCondition 1.3.6.1.4.1.232.25.1.3
The overall condition (status) of the system represented by this MIB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), ok(2), degraded(3), failed(4)  

cpqSasSwitchTestTrap 1
SAS Switch Test Trap
TRAP-TYPE    

cpqSasSwitchHwStatusChangeTrap 101
SAS Switch Status change The switch has detected a change in the status. The new status is defined in cpqSasSwitchHwStatus.
TRAP-TYPE    

cpqSasSwitchHwRedundancyStateChangeTrap 201
SAS Switch Redundancy State change. The switch has detected a change in the redundancy operation mode. The new redundancy state is defined in cpqSasSwitchHwRedundancyState.
TRAP-TYPE    

cpqSasSwitchPhysicalDriveAddedTrap 301
SAS switch detected physical drive added to attached enclosure. The switch has detected a physical drive has been added to attached storage enclosure.
TRAP-TYPE    

cpqSasSwitchPhysicalDriveRemovedTrap 302
SAS switch detected physical drive removed from attached enclosure. The switch has detected a physical drive has been removed from attached storage enclosure.
TRAP-TYPE    

cpqSasSwitchStorageEnclosureAddedTrap 401
SAS switch detected storage enclosure added. The switch has detected a storage enclosure has been added.
TRAP-TYPE    

cpqSasSwitchStorageEnclosureRemovedTrap 402
SAS switch detected storage enclosure removed. The switch has detected a storage enclosure has been removed.
TRAP-TYPE    

cpqSasSwitchHwStatus 1.3.6.1.4.1.232.25.2.2.2
The Status of the SAS Switch. The switch can be in one of the following states: other(1) The switch is in a state other than one of those listed below. ok(2) Indicates that the switch is in normal operation mode. No user action is necessary. degraded(3) Indicates that the switch is operating in a degraded manner. User intervention required. failed(4) Indicates that the switch is in a failed state and is not operating. User action is required.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), ok(2), degraded(3), failed(4)  

cpqSasSwitchHwRedundancyState 1.3.6.1.4.1.232.25.2.2.3
The Redundancy State for the SAS Switch. The switch can be in one of the following redundant states: other(1) The switch is in a state other than one of those listed below. active(2) Indicates that the switch is acting in a redundant configuration and the switch is operating in the active state. No user action is necessary. standby(3) Indicates that the switch is acting in a redundant configuration and the switch is operating in the standby state. No user action is necessary. notConfigured(4) Indicates that the switch is in a non redundant configuration and the switch not configured correctly since the switch has been moved from a different location. User action is required. notRedundant(5) Indicates that the switch is operating is a non redundant configuration. No user action is necessary. degraded(6) Indicates that the switch cannot communicate with its partner switch. User action is necessary. mismatch(7) Indicates that there is a mismatch in firmware versions or zoning configurations between the redundant switches. User action is necessary to upgrade firmware or select desired zoning configuration by forcing appropriate switch to active state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), active(2), standby(3), notConfigured(4), notRedundant(5), degraded(6), mismatch(7)