COM21-HCXTX-MIB
File:
COM21-HCXTX-MIB.mib (20057 bytes)
Imported modules
Imported symbols
Defined Types
Defined Values
| com21HcxTx |
1.3.6.1.4.1.1141.2.20 |
| This is the Com21 ComController TX Unit Control
MIB module. COM21 Part# 005-0025-00 |
| MODULE-IDENTITY |
|
|
|
| hcxDownstreamShelfId |
1.3.6.1.4.1.1141.2.23.1 |
|
contains the associated shelf id. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..2 |
|
| hcxDownstreamBootVersion |
1.3.6.1.4.1.1141.2.23.4 |
|
contains the version of the TX card boot ROM.
An empty string if card not present. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(16) |
|
| hcxDnstrmUnitPrimStateChange |
1.3.6.1.4.1.1141.4.60 |
|
Generated whenever a the hcxDnstreamUnitPrimServState
changes in value. This an event with no clear
condition. Only severity is WARNING. |
| Status: current |
Access: read-only |
| NOTIFICATION-TYPE |
|
|
|
| hcxDnstreamUnitSecServState |
1.3.6.1.4.1.1141.2.23.6 |
|
contains a string defining the secondary service states
of the Downstream Unit. The substrings supported by
the Downstream Unit shall be: TEST - in test, as
set by hcxDnUnitConfigState, STBY - standby, again set
by hcxDnUnitConfigState, MT - maintenance, set by
hcxDnUnitConfigState, FAULT - hardware failure, UNEQ -
unequipped. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(16) |
|
| hcxDnstrmUnitSecStateChange |
1.3.6.1.4.1.1141.4.61 |
|
Generated whenever a the hcxDnstreamUnitSecServState
changes in value. This an event with no clear
condition. Only severity is WARNING. |
| Status: current |
Access: read-only |
| NOTIFICATION-TYPE |
|
|
|
| hcxDnUnitConfigState |
1.3.6.1.4.1.1141.2.23.7 |
|
The Downstream Unit State is an active-value.
Note that because we have only one port per card
then this state change is exactly the same as
hcxDnstrmPortState. Note that initially standby
will be the same state as offline. Later this will
change when TX redundancy is supported. offline
is default. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
offline(2000), online(2001), test(2002), standby(2003) |
|
| hcxDnUnitRestartAction |
1.3.6.1.4.1.1141.2.23.8 |
|
The TX Unit Action is an active-value. The setting
of this attibute to restart(2) causes the TX card
to reset and download a new image. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
nil(1), restart(2) |
|
| hcxDnDiagTestAction |
1.3.6.1.4.1.1141.2.23.9 |
|
This attribute is used to invoke the internal
TX diagnostic test. In order to activate this
test, the card must be placed in the test state. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
nil(1), execute(2) |
|
| hcxDnDiagTestComplete |
1.3.6.1.4.1.1141.4.62 |
|
This notification is generated whenever the TX
internal diagnostic tests are completed. This an event
with no clear condition. Only severity is WARNING. |
| Status: current |
Access: read-write |
| NOTIFICATION-TYPE |
|
|
|
| hcxDnDiagTestResult |
1.3.6.1.4.1.1141.2.23.10 |
|
This attribute contains the result of the last TX
diagnostic test. Details TBD. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
inprogress(1), success(2), failure(3), invalidState(4) |
|
| hcxDnTestStatusLed |
1.3.6.1.4.1.1141.2.23.11 |
|
The TX Test Status LED is a read-only attribute
which describes the condition of the TX
Test Status light emitting diode located on
the RX board. A value of on(1) indicates that a
service effecting test is in progress and that
the LED is illuminated. off if card not present. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
on(1), off(2) |
|
| hcxDnTestStatusLedChange |
1.3.6.1.4.1.1141.4.63 |
|
generated whenever there is a change in test LED
status. This an event with no clear condition.
Only severity is WARNING. |
| Status: current |
Access: read-only |
| NOTIFICATION-TYPE |
|
|
|
| hcxDnFaultStatusLed |
1.3.6.1.4.1.1141.2.23.12 |
|
The RX Fault Status LED is a read-only attribute
which describes the condition of the TX
Fault Status light emitting diode located on
the TX board. A value of on(1) indicates that an
fault condition has been detected (for which a
trap will have been issued) and the LED is
illuminated. off if card not present. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
on(1), off(2) |
|
| hcxDnFaultStatusLedChange |
1.3.6.1.4.1.1141.4.64 |
|
generated whenever there is a change in the Fault
LED status. This an event with no clear condition.
Only severity is WARNING. |
| Status: current |
Access: read-only |
| NOTIFICATION-TYPE |
|
|
|
| hcxDnOperationFailure |
1.3.6.1.4.1.1141.4.65 |
|
This notification is generated by the CC whenever
a TX card fails to respond correctly to a
request. This failure could indicate either a
resource problem or software failure. Note that
if a TX card failures to respond completely to
a CC request, then a hcxInsertChange trap shall
be generated. This is an event with no clear
condition. Only severity is WARNING. |
| Status: current |
Access: read-only |
| NOTIFICATION-TYPE |
|
|
|
| hcxDownstreamSerialNumber |
1.3.6.1.4.1.1141.2.23.13 |
|
contains the serial number of the TX card.
An empty string if card not present. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(16) |
|
| hcxDownstreamPortId |
1.3.6.1.4.1.1141.2.21.1 |
|
contains downstream port id. Initially at least, only 1
supported. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hcxXmitFrequency |
1.3.6.1.4.1.1141.2.21.2 |
|
Contains the transmit frequency of the RF port in
KHz. If this value is changed AFTER the acquisition of
ComPorts then a corresponding change to the
stuXmitFrequency attribute shall be broadcast to all
the acquired ComPorts. Minimum step size is 200. i.e.
200000hz. Default is 0. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
88000..800000 |
|
| hcxXmitGain |
1.3.6.1.4.1.1141.2.21.3 |
|
Transmit gain is used to specify the power level in
the ComController transmitter. Default is 0. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
45..60 |
|
| hcxSynthLockLossDetected |
1.3.6.1.4.1.1141.4.68 |
| Default severity is MINOR. |
| Status: current |
Access: read-write |
| NOTIFICATION-TYPE |
|
|
|
| hcxSynthLockLossClear |
1.3.6.1.4.1.1141.4.69 |
| Severity is CLEARED. |
| Status: current |
Access: read-write |
| NOTIFICATION-TYPE |
|
|
|
| hcxLossOfFrameClkDetected |
1.3.6.1.4.1.1141.4.70 |
| Default severity is MINOR. |
| Status: current |
Access: read-write |
| NOTIFICATION-TYPE |
|
|
|
| hcxLossOfFrameClkClear |
1.3.6.1.4.1.1141.4.71 |
| Severity is CLEARED. |
| Status: current |
Access: read-write |
| NOTIFICATION-TYPE |
|
|
|
| hcxStatsCurrMinTxCells |
1.3.6.1.4.1.1141.2.22.1 |
|
Represents the number of cells transmitted in the
current 15 minute period. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| hcxStatsCurrMinTxNullCells |
1.3.6.1.4.1.1141.2.22.2 |
|
Represents the number of null cells transmitted in the
current 15 minute period. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| hcxStatsPrevMinTxCells |
1.3.6.1.4.1.1141.2.22.3 |
|
Represents the number of cells transmitted in the
previous 15 minute period. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| hcxStatsPrevMinTxNullCells |
1.3.6.1.4.1.1141.2.22.4 |
|
Represents the number of null cells transmitted in the
previous 15 minute period. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| hcxDownstreamUtil |
1.3.6.1.4.1.1141.2.22.5 |
|
Represents the percentage of utilization on the
downstream channel - the RF TX will stuff with null
cells to match line rate.
i.e. traffic cells/(traffic cells + null cells) * 100.
This figure is updated every second. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| hcxStatsClearTxCurrStats |
1.3.6.1.4.1.1141.2.22.6 |
|
This attribute is used to clear current TX
statistics counters in this group. This operation
is only possible if the hcxStatsControl attribute
is set to wrapCurr. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
nil(1), clear(2) |
|