COM21-HCXETH-MIB

File: COM21-HCXETH-MIB.mib (55607 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	COM21-HCX-MIB
COM21-HCXALM-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
Integer32	IpAddress	Gauge32
MacAddress	DisplayString	com21
com21Hcx	com21Traps	hcxAlmSeverity
hcxEventLogTime

Defined Types

PrimServiceState
INTEGER	is(1), oos(2)

Com21RowStatus
INTEGER	active(1), create(2), destroy(3), deactive(4)

HcxEtherUnitEntry
SEQUENCE
	hcxEtherShelfId	INTEGER
	hcxEtherSlotId	Integer32
	hcxEtherCardType	INTEGER
	hcxEtherNoPorts	INTEGER
	hcxEtherHardwareVersion	DisplayString
	hcxEtherBootVersion	DisplayString
	hcxEtherUnitPrimServState	PrimServiceState
	hcxEtherUnitSecServState	DisplayString
	hcxEtherRestartAction	INTEGER
	hcxEtherTestStatusLed	INTEGER
	hcxEtherFaultStatusLed	INTEGER
	hcxEtherSerialNumber	DisplayString

HcxEtherPortEntry
SEQUENCE
	hcxEtherPortShelfId	INTEGER
	hcxEtherPortSlotId	Integer32
	hcxEtherPortId	INTEGER
	hcxEtherPortType	INTEGER
	hcxEtherPortService	DisplayString
	hcxEtherPortPrimServState	PrimServiceState
	hcxEtherPortSecServState	DisplayString
	hcxEtherMaxBandwidth	INTEGER
	hcxEtherAggrDnStrmCbrRate	Integer32
	hcxEtherAggrDnStrmPcrRate	Integer32
	hcxEtherAggrUpStrmCbrRate	Integer32
	hcxEtherAggrUpStrmMinRate	Integer32
	hcxEtherAggrUpStrmMaxRate	Integer32
	hcxEtherAgeTime	Integer32
	hcxEtherPortConfigState	INTEGER
	hcxEtherPortRestartAction	INTEGER
	hcxEtherPortDiagTestAction	INTEGER
	hcxEtherPortDiagTestResult	INTEGER
	hcxEtherPortLinkStatusLed	INTEGER
	hcxEtherPortArpFiltRate	INTEGER
	hcxEtherAggrActDnStrmCbrRate	Integer32
	hcxEtherAggrActDnStrmPcrRate	Integer32
	hcxEtherAggrActUpStrmCbrRate	Integer32
	hcxEtherAggrActUpStrmMinRate	Integer32
	hcxEtherAggrActUpStrmMaxRate	Integer32
	hcxEtherPortIpAddr	IpAddress
	hcxEtherPortIpMask	IpAddress
	hcxEtherPortMacAddr	MacAddress
	hcxEtherPortAutoNegEnable	INTEGER
	hcxEtherPortSpeedSelect	INTEGER
	hcxEtherCurrPortState	INTEGER

HcxEtherStatsEntry
SEQUENCE
	hcxEtherStatsShelfId	INTEGER
	hcxEtherStatsSlotId	Integer32
	hcxEtherStatsPortId	INTEGER
	hcxEtherCurrCollisions	Gauge32
	hcxEtherCurrRunts	Gauge32
	hcxEtherCurrGrunts	Gauge32
	hcxEtherCurrCrcPkts	Gauge32
	hcxEtherCurrTxPkts	Gauge32
	hcxEtherCurrRxPkts	Gauge32
	hcxEtherPrevCollisions	Gauge32
	hcxEtherPrevRunts	Gauge32
	hcxEtherPrevGrunts	Gauge32
	hcxEtherPrevCrcPkts	Gauge32
	hcxEtherPrevTxPkts	Gauge32
	hcxEtherPrevRxPkts	Gauge32
	hcxEtherClearStats	INTEGER

HcxEtherStuStatsEntry
SEQUENCE
	hcxEtherStuStatsMacAddr	MacAddress
	hcxEtherStuCurrDnstrmBytes	Gauge32
	hcxEtherStuCurrUpstrmBytes	Gauge32
	hcxEtherStuCurrUpstrmAal5CrcErrs	Gauge32
	hcxEtherStuCurrDnstrmDropPkts	Gauge32
	hcxEtherStuPrevDnstrmBytes	Gauge32
	hcxEtherStuPrevUpstrmBytes	Gauge32
	hcxEtherStuPrevUpstrmAal5CrcErrs	Gauge32
	hcxEtherStuPrevDnstrmDropPkts	Gauge32
	hcxEtherStuClearStats	INTEGER

HcxEtherIpAddrListEntry
SEQUENCE
	hcxEtherIpAddrShelfId	INTEGER
	hcxEtherIpAddrSlotId	Integer32
	hcxEtherIpAddrPortId	INTEGER
	hcxEtherIpAddrIPAddr	IpAddress
	hcxEtherIpAddrIPMask	IpAddress
	hcxEtherIpAddrIPStatus	Com21RowStatus

HcxServGrpAssocEntry
SEQUENCE
	hcxServGrpAssocShelfId	INTEGER
	hcxServGrpAssocSlotId	INTEGER
	hcxServGrpAssocCardType	INTEGER
	hcxServGrpAssocPortId	Integer32
	hcxServGrpAssocEntryId	Integer32
	hcxServGrpAssocRate	Integer32
	hcxServGrpAssocType	INTEGER
	hcxServGrpAssocNumOfVlans	Integer32
	hcxServGrpAssocNumOfStus	Integer32

Defined Values

com21HcxEth		1.3.6.1.4.1.1141.2.40
This is the Com21 ComController Ethernet MIB module. COM21 Part# 005-0025-00
MODULE-IDENTITY

com21HcxEtherUnitGroup		1.3.6.1.4.1.1141.2.41
OBJECT IDENTIFIER

com21HcxEtherPortGroup		1.3.6.1.4.1.1141.2.42
OBJECT IDENTIFIER

com21HcxEtherStatsGroup		1.3.6.1.4.1.1141.2.43
OBJECT IDENTIFIER

com21HcxEtherIpAddrGroup		1.3.6.1.4.1.1141.2.44
OBJECT IDENTIFIER

com21HcxEtherStuStatsGroup		1.3.6.1.4.1.1141.2.45
OBJECT IDENTIFIER

com21HcxServGrpAssocGroup		1.3.6.1.4.1.1141.2.46
OBJECT IDENTIFIER

com21HcxEtherUnitTable		1.3.6.1.4.1.1141.2.41.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HcxEtherUnitEntry

com21HcxEtherUnitEntry		1.3.6.1.4.1.1141.2.41.1.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	HcxEtherUnitEntry

hcxEtherShelfId		1.3.6.1.4.1.1141.2.41.1.1.1
contains the associated shelf id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2

hcxEtherSlotId		1.3.6.1.4.1.1141.2.41.1.1.2
contains associated slot id.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherCardType		1.3.6.1.4.1.1141.2.41.1.1.3
contains Ethernet card type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	tenBaseT(1), onehundredBaseT(2)

hcxEtherNoPorts		1.3.6.1.4.1.1141.2.41.1.1.4
contains the number of ports supported by the Ethernet card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

hcxEtherHardwareVersion		1.3.6.1.4.1.1141.2.41.1.1.5
contains the hardware version of the Ethernet card. Will contain empty string if card has not been inserted in the slot.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(16)

hcxEtherBootVersion		1.3.6.1.4.1.1141.2.41.1.1.6
contains the version of the Ethernet card boot ROM. Will contain empty string if card has not been inserted in the slot.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(16)

hcxEtherUnitPrimServState		1.3.6.1.4.1.1141.2.41.1.1.7
contains primary service state of the Ethernet Unit.
Status: current	Access: read-only
OBJECT-TYPE
	PrimServiceState

hcxEtherUnitPrimStateChange		1.3.6.1.4.1.1141.4.20
This trap is generated whenever a change in the the hcxEtherUnitPrimServState occurs. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxEtherUnitSecServState		1.3.6.1.4.1.1141.2.41.1.1.8
contains a string defining the secondary service states of the Ethernet Unit. The substrings supported by the Ethernet Unit shall be: UNEQ - unequipped.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(16)

hcxEtherUnitSecStateChange		1.3.6.1.4.1.1141.4.21
This trap is generated whenever a change in the the hcxEtherUnitSecServState occurs. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxEtherRestartAction		1.3.6.1.4.1.1141.2.41.1.1.9
The Ethernet Unit Restart Action is an active-value. The setting of this attribute to restart(2) causes the Ethernet card to reset and download a new image.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nil(1), restart(2)

hcxEtherTestStatusLed		1.3.6.1.4.1.1141.2.41.1.1.10
The Ethernet Test Status LED is a read-only attribute which describes the condition of the Ethernet Test Status light emitting diode located on the Ethernet board. A value of on(1) indicates that a service effecting test is in progress and that the LED is illuminated. Will be off if no card present.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

hcxEtherTestStatusLedChange		1.3.6.1.4.1.1141.4.22
generated whenever there is a change in test LED status. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxEtherFaultStatusLed		1.3.6.1.4.1.1141.2.41.1.1.11
The Ethernet Fault Status LED is a read-only attribute which describes the condition of the Ethernet Fault Status light emitting diode located on the Ethernet board. A value of on(1) indicates that an fault condition has been detected (for which a trap will have been issued) and the LED is illuminated. Will be off if no card present.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

hcxEtherFaultStatusLedChange		1.3.6.1.4.1.1141.4.23
generated whenever there is a change in the Fault LED status. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxEtherSerialNumber		1.3.6.1.4.1.1141.2.41.1.1.12
contains the serial number of the Ethernet card. Will contain empty string if card has not been inserted in the slot.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(16)

com21HcxEtherPortTable		1.3.6.1.4.1.1141.2.42.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HcxEtherPortEntry

com21HcxEtherPortEntry		1.3.6.1.4.1.1141.2.42.1.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	HcxEtherPortEntry

hcxEtherPortShelfId		1.3.6.1.4.1.1141.2.42.1.1.1
contains shelf in which this Ethernet port is located.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2

hcxEtherPortSlotId		1.3.6.1.4.1.1141.2.42.1.1.2
contains slot in which this Ethernet port is located.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherPortId		1.3.6.1.4.1.1141.2.42.1.1.3
contains Ethernet port id. Represents the port number on the card. In the case of single 10baseT or 100baseT, this value will always be 1. In the case of a quad 10baseT card, this value is in the range 1-4.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

hcxEtherPortType		1.3.6.1.4.1.1141.2.42.1.1.4
contains type of Ethernet port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	tenBaseT(1), onehundredBaseT(2)

hcxEtherPortService		1.3.6.1.4.1.1141.2.42.1.1.5
contains string defining the service provided by the Ethernet port (VLAN). Set by NMAPS. Default null string. CC most ensure uniqueness.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(32)

hcxEtherPortPrimServState		1.3.6.1.4.1.1141.2.42.1.1.6
contains primary service state of the Ethernet Unit. This state shall be effected by the hcxEtherPortState attribute.
Status: current	Access: read-only
OBJECT-TYPE
	PrimServiceState

hcxEtherPortPrimStateChange		1.3.6.1.4.1.1141.4.24
This trap is generated whenever a change in the the hcxEtherPortPrimServState occurs. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxEtherPortSecServState		1.3.6.1.4.1.1141.2.42.1.1.7
contains a string defining the secondary service states of the Ethernet Unit. The substrings supported by the Ethernet Unit shall be: MT - offline, set by hcxEthernetUnitState, FAULT - hardware failure, TEST - test, UNEQ - unequipped.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(16)

hcxEtherPortSecStateChange		1.3.6.1.4.1.1141.4.25
This trap is generated whenever a change in the the hcxEtherPortSecServState occurs. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxEtherMaxBandwidth		1.3.6.1.4.1.1141.2.42.1.1.9
This attribute defines the maximum output payload bandwidth associated with the Ethernet port. Defined in thousands of bps. From 0 to 22222. This value shall be checked by the CC which shall ensure that the aggregate of the hcxEtherMaxBandwidth attributes for each of the Ethernet ports does not exceed the system maximum. Note max for 10bT port is 11560. Default: 7000.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..22222

hcxEtherAggrDnStrmCbrRate		1.3.6.1.4.1.1141.2.42.1.1.12
This attribute specifies the aggregate of all ComPort downstream CBR rates configured on the Ethernet port (VLAN). This includes both acquired and unacquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherAggrDnStrmPcrRate		1.3.6.1.4.1.1141.2.42.1.1.13
This attribute specifies the aggregate of all ComPort downstream PCR rates configured on the Ethernet port (VLAN). This includes both acquired and unacquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherAggrUpStrmCbrRate		1.3.6.1.4.1.1141.2.42.1.1.14
This attribute specifies the aggregate of all ComPort upstream CBR rates configured on the Ethernet port (VLAN). This includes both acquired and unacquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherAggrUpStrmMinRate		1.3.6.1.4.1.1141.2.42.1.1.15
This attribute specifies the aggregate of all ComPort upstream minimum PCR rates on the Ethernet port (VLAN). This includes both acquired and unacquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherAggrUpStrmMaxRate		1.3.6.1.4.1.1141.2.42.1.1.16
This attribute specifies the aggregate of all ComPort upstream maximum cell rates on the Ethernet port (VLAN). This includes both acquired and unacquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherAgeTime		1.3.6.1.4.1.1141.2.42.1.1.17
This attribute defines, in seconds, the aging time for non-accessed entries in the Bridge mapping table. The default shall be 300secs. If this set to 0, then aging is disabled.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hcxEtherPortConfigState		1.3.6.1.4.1.1141.2.42.1.1.18
The Ethernet Port State is an active-value. The Ethernet port will default to offline, in which case no traffic shall be passed. Default offline.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	offline(2000), online(2001), test(2002)

hcxEtherPortRestartAction		1.3.6.1.4.1.1141.2.42.1.1.19
The Ethernet Port Restart Action is an active-value. The setting of this attribute to restart(2) causes the Ethernet port to reset and download a new image.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nil(1), restart(2)

hcxEtherPortDiagTestAction		1.3.6.1.4.1.1141.2.42.1.1.20
This attribute is used to invoke the internal Ethernet card diagnostic test. In order to activate this test, the card must be placed in the test state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nil(1), execute(2)

hcxEtherPortDiagTestComplete		1.3.6.1.4.1.1141.4.26
This notification is generated whenever the Ethernet port internal diagnostic tests are completed. Event only, no clear. Only severity allowed is WARNING.
Status: current	Access: read-write
NOTIFICATION-TYPE

hcxEtherPortDiagTestResult		1.3.6.1.4.1.1141.2.42.1.1.21
This attribute contains the result of the last Ethernet port diagnostic test.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inprogress(1), success(2), failure(3), invalidState(4)

hcxEtherOperationFailure		1.3.6.1.4.1.1141.4.27
This notification is generated by the CC whenever an Ethernet port fails to respond correctly to a request. This failure could indicate either a resource problem or software failure. Note that if an Ethernet card failures to respond completely to a CC request, then a hcxInsertChange trap shall be generated. This is an event without a corresponding clear. Only severity allowed is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxEtherPortLinkStatusLed		1.3.6.1.4.1.1141.2.42.1.1.22
The Ethernet Link Status LED is a read-only attribute which describes the condition of the Ethernet Link Status light emitting diode located on the Ethernet board. A value of on(1) indicates that the link is up and active, and that the LED is illuminated. Will be off if no card present.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

hcxEtherPortLinkStatusLedChange		1.3.6.1.4.1.1141.4.28
generated whenever there is a change in link LED status. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxEtherPortArpFiltRate		1.3.6.1.4.1.1141.2.42.1.1.24
No longer supported
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	10000..150000

hcxEtherAggrActDnStrmCbrRate		1.3.6.1.4.1.1141.2.42.1.1.25
This attribute specifies the aggregate of all ComPort downstream CBR rates active on the Ethernet port (VLAN). This includes only acquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherAggrActDnStrmPcrRate		1.3.6.1.4.1.1141.2.42.1.1.26
This attribute specifies the aggregate of all ComPort downstream PCR rates active on the Ethernet port (VLAN). This includes only acquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherAggrActUpStrmCbrRate		1.3.6.1.4.1.1141.2.42.1.1.27
This attribute specifies the aggregate of all ComPort upstream CBR rates active on the Ethernet port (VLAN). This includes only acquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherAggrActUpStrmMinRate		1.3.6.1.4.1.1141.2.42.1.1.28
This attribute specifies the aggregate of all ComPort upstream minimum PCR rates active on the Ethernet port (VLAN). This includes only acquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherAggrActUpStrmMaxRate		1.3.6.1.4.1.1141.2.42.1.1.29
This attribute specifies the aggregate of all ComPort upstream maximum cell rates active on the Ethernet port (VLAN). This includes only acquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherPortIpAddr		1.3.6.1.4.1.1141.2.42.1.1.30
IP Address associated with this ethernet port. This is a future item for telephone return support.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

hcxEtherPortIpMask		1.3.6.1.4.1.1141.2.42.1.1.31
IP mask associated with port. Default is ff.ff.ff.ff. This is a future item for telephone return support.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

hcxEtherPortMacAddr		1.3.6.1.4.1.1141.2.42.1.1.32
MAC address associated with port.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

hcxEtherPortAutoNegEnable		1.3.6.1.4.1.1141.2.42.1.1.33
This attribute is used for 100BaseT ports ONLY, to enable/disable Auto Negotiation Feature. Default is Auto Negotiation Enable. For 10bT ports this attribute will be read-only with a value of off.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

hcxEtherPortSpeedSelect		1.3.6.1.4.1.1141.2.42.1.1.34
If 'hcxEtherPortAutoNegEnble' is set to 'off' then the Media speed of the port is set to the value in this attribute. This attribute is valid only for 100BaseT ports - for 10bT ports this attribute shall be read-only with a value of tenMbpsHalfDuplex. Default for 100bT ports is 'hundredMbps'. An error will be returned if PortSpeed is set to 'tenMbps' and 'hcxEtherMaxBandwidth' is greater than 10 Mbps
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tenMbpsHalfDuplex(1), tenMbpsFullDuplex(2), hundredMbpsHalfDulplex(3), hundredMbpsFullDuplex(4)

hcxEtherCurrPortState		1.3.6.1.4.1.1141.2.42.1.1.35
specifies the Media speed of the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	linkFail(1), autoNegPending(2), autoNegFailure(3), tenMbpsHalfDuplex(4), tenMbpsFullDuplex(5), hundredMbpsHalfDulplex(6), hundredMbpsFullDuplex(7)

com21HcxEtherStatsTable		1.3.6.1.4.1.1141.2.43.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HcxEtherStatsEntry

com21HcxEtherStatsEntry		1.3.6.1.4.1.1141.2.43.1.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	HcxEtherStatsEntry

hcxEtherStatsShelfId		1.3.6.1.4.1.1141.2.43.1.1.1
contains shelf in which the associated Ethernet port is located.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2

hcxEtherStatsSlotId		1.3.6.1.4.1.1141.2.43.1.1.2
contains slot in which the associated Ethernet port is located.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherStatsPortId		1.3.6.1.4.1.1141.2.43.1.1.3
contains the associated Ethernet port id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

hcxEtherCurrCollisions		1.3.6.1.4.1.1141.2.43.1.1.4
contains the number of detected collisions in the current 15 minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherCurrRunts		1.3.6.1.4.1.1141.2.43.1.1.5
contains the number of receive runt packets in the current 15 minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherCurrGrunts		1.3.6.1.4.1.1141.2.43.1.1.6
contains the number of received grunt packets in the current 15 minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherCurrCrcPkts		1.3.6.1.4.1.1141.2.43.1.1.7
contains the number of ethernet packets with CRC errors received in the current 15 minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherCurrTxPkts		1.3.6.1.4.1.1141.2.43.1.1.8
contains the number of ethernet packets transmitted in the current 15 minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherCurrRxPkts		1.3.6.1.4.1.1141.2.43.1.1.9
contains the number of ethernet packets received in the current 15 minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherPrevCollisions		1.3.6.1.4.1.1141.2.43.1.1.10
contains the number of detected collisions in the previous 15 minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherPrevRunts		1.3.6.1.4.1.1141.2.43.1.1.11
contains the number of received runt packets in the previous 15 minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherPrevGrunts		1.3.6.1.4.1.1141.2.43.1.1.12
contains the number of received grunt packets in the previous 15 minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherPrevCrcPkts		1.3.6.1.4.1.1141.2.43.1.1.13
contains the number of ethernet packets received with CRC errors in the previous 15 minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherPrevTxPkts		1.3.6.1.4.1.1141.2.43.1.1.14
contains the number of ethernet packets transmitted in the previous 15 minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherPrevRxPkts		1.3.6.1.4.1.1141.2.43.1.1.15
contains the number of ethernet packets received in the previous 15 minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherClearStats		1.3.6.1.4.1.1141.2.43.1.1.16
This attribute is used to clear all Ethernet statistics counters in this group. This operation is only possible if the hcxStatsControl attribute is set to wrapCurr.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nil(1), clear(2)

com21HcxEtherStuStatsTable		1.3.6.1.4.1.1141.2.45.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HcxEtherStuStatsEntry

com21HcxEtherStuStatsEntry		1.3.6.1.4.1.1141.2.45.1.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	HcxEtherStuStatsEntry

hcxEtherStuStatsMacAddr		1.3.6.1.4.1.1141.2.45.1.1.1
Contains IEEE 802 medium access control address of the ComPort device.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

hcxEtherStuCurrDnstrmBytes		1.3.6.1.4.1.1141.2.45.1.1.2
Contains the number of unicast bytes transmitted downstream to this ComPort in the current 15 minute collection period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherStuCurrUpstrmBytes		1.3.6.1.4.1.1141.2.45.1.1.3
Contains the number of bytes received upstream from this ComPort in the current 15 minute collection period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherStuCurrUpstrmAal5CrcErrs		1.3.6.1.4.1.1141.2.45.1.1.4
Contains the number of AAL5 CRC errors related to upstream traffic from the ComPort in the current 15 minute collection period. Each of these errors indicates a dropped Ethernet frame.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherStuCurrDnstrmDropPkts		1.3.6.1.4.1.1141.2.45.1.1.5
Contains the number of dropped Ethernet frames in the downstream direction in the current 15min period. These frames are generally dropped due to policing.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherStuPrevDnstrmBytes		1.3.6.1.4.1.1141.2.45.1.1.6
Contains the number of unicast bytes transmitted downstream to this ComPort in the last 15 minute collection period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherStuPrevUpstrmBytes		1.3.6.1.4.1.1141.2.45.1.1.7
Contains the number of bytes received upstream from this ComPort in the last 15 minute collection period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherStuPrevUpstrmAal5CrcErrs		1.3.6.1.4.1.1141.2.45.1.1.8
Contains the number of AAL5 CRC errors related to upstream traffic from the ComPort in the last 15 minute collection period. Each of these errors indicates a dropped Ethernet frame.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherStuPrevDnstrmDropPkts		1.3.6.1.4.1.1141.2.45.1.1.9
Contains the number of dropped RX frames in the upstream direction in the previous 15min period.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hcxEtherStuClearStats		1.3.6.1.4.1.1141.2.45.1.1.10
This attribute is used to clear all ComPort statistics counters in this group. This operation is only possible if the hcxStatsControl attribute is set to wrapCurr.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nil(1), clear(2)

com21HcxEtherIpAddrTable		1.3.6.1.4.1.1141.2.44.1
TBD.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HcxEtherIpAddrListEntry

com21HcxEtherIpAddrEntry		1.3.6.1.4.1.1141.2.44.1.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	HcxEtherIpAddrListEntry

hcxEtherIpAddrShelfId		1.3.6.1.4.1.1141.2.44.1.1.1
contains shelf in which the associated Ethernet port is located.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2

hcxEtherIpAddrSlotId		1.3.6.1.4.1.1141.2.44.1.1.2
contains slot in which the associated Ethernet port is located.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxEtherIpAddrPortId		1.3.6.1.4.1.1141.2.44.1.1.3
contains the associated Ethernet port id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

hcxEtherIpAddrIPAddr		1.3.6.1.4.1.1141.2.44.1.1.4
target IP Address. No ComPort will be able to use this IP address in an ARP response.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

hcxEtherIpAddrIPMask		1.3.6.1.4.1.1141.2.44.1.1.5
IP mask. Default is ff.ff.ff.ff.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

hcxEtherIpAddrIPStatus		1.3.6.1.4.1.1141.2.44.1.1.6
Used to delete or create an entry.
Status: current	Access: read-create
OBJECT-TYPE
	Com21RowStatus

com21HcxServGrpAssocTable		1.3.6.1.4.1.1141.2.46.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HcxServGrpAssocEntry

com21HcxServGrpAssocEntry		1.3.6.1.4.1.1141.2.46.1.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	HcxServGrpAssocEntry

hcxServGrpAssocShelfId		1.3.6.1.4.1.1141.2.46.1.1.1
defines shelfId to index into this entry. It is the ShelfId where this Service Group has an entry
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2

hcxServGrpAssocSlotId		1.3.6.1.4.1.1141.2.46.1.1.2
defines SlotId to index into this entry. It is the slot where this Service Group has an entry
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2

hcxServGrpAssocCardType		1.3.6.1.4.1.1141.2.46.1.1.3
defines cardType to index into this entry. It is the card Type where this Service Group has an entry
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	tenBaseT(1), onehundredBaseT(2), oc3(3)

hcxServGrpAssocPortId		1.3.6.1.4.1.1141.2.46.1.1.4
defines portId to index into this entry. It is the port number where this Service Group has an entry
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxServGrpAssocEntryId		1.3.6.1.4.1.1141.2.46.1.1.5
defines entryId to index into this entry. it is the entry number assigned to this service group
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxServGrpAssocRate		1.3.6.1.4.1.1141.2.46.1.1.6
contains Rate associated with this Entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxServGrpAssocType		1.3.6.1.4.1.1141.2.46.1.1.7
contains Type associated with this Entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cbr(1), ondemand(2)

hcxServGrpAssocNumOfVlans		1.3.6.1.4.1.1141.2.46.1.1.8
contains number of Vlans associated with this Service Group
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxServGrpAssocNumOfStus		1.3.6.1.4.1.1141.2.46.1.1.9
contains number of Stus associated with this Service Group
Status: current	Access: read-only
OBJECT-TYPE
	Integer32