CM-SA-MIB

File: CM-SA-MIB.mib (272622 bytes)

Imported modules

SNMPv2-CONF	SNMPv2-SMI	SNMPv2-TC
IPV6-TC	ADVA-MIB	CM-COMMON-MIB
CM-ENTITY-MIB	CM-FACILITY-MIB	IEEE8021-CFM-MIB

Imported symbols

MODULE-COMPLIANCE	OBJECT-GROUP	NOTIFICATION-GROUP
MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
Integer32	IpAddress	Unsigned32
Counter64	DateAndTime	DisplayString
TruthValue	RowStatus	StorageType
MacAddress	VariablePointer	TEXTUAL-CONVENTION
Ipv6Address	fsp150cm	TrafficDirection
VlanId	VlanPriority	IpVersion
IpPriorityMapMode	ScheduleType	ClassOfServiceType
CmPmBinAction	neIndex	shelfIndex
slotIndex	BitErrRate	PolicerColorMode
AdminState	OperationalState	SecondaryState
PerfCounter64	PerfCounter32	SchedActivityStatus
MepDestinationType	Dot1agCfmMepIdOrZero

Defined Types

EcpaTestStatus
ECPA Test Status.
TEXTUAL-CONVENTION
	INTEGER	initial(1), in-progress(2), stopped(3), completed(4), aborted(5)

EcpaPayloadType
ECPA Payload Type.
TEXTUAL-CONVENTION
	INTEGER	fixed(1), random(2)

EcpaTestType
ECPA Control Test Type.
TEXTUAL-CONVENTION
	INTEGER	duration(1), numframes(2), continuous(3)

EcpaControlAction
ECPA Control Action.
TEXTUAL-CONVENTION
	INTEGER	not-applicable(0), start(1), stop(2)

EsaProbeProtocol
ESA Probe Protocol Types.
TEXTUAL-CONVENTION
	INTEGER	icmpEcho(1), udpEcho(2), icmpTimestamp(3), y1731(4), y1731-slm-slr(5), y1731-slm-dmm(6)

EsaProbeDirection
ESA Probe Direction.
TEXTUAL-CONVENTION
	INTEGER	up(1), down(2)

EsaReflectorDirection
ESA Reflector Direction.
TEXTUAL-CONVENTION
	INTEGER	up(1), down(2)

EsaProbePmIntervalType
ESA Probe PM Interval Types.
TEXTUAL-CONVENTION
	INTEGER	current(1), rollover(2)

EsaProbeHistoryIntervalType
ESA Probe Y1731 History Interval Types.
TEXTUAL-CONVENTION
	INTEGER	interval-1min(1), interval-5min(2), interval-10min(3), interval-15min(4), interval-60min(5)

EsaProbeDistStatsType
Indicates the ESA Probe Statistics Distribution Type.
TEXTUAL-CONVENTION
	INTEGER	roundtrip-delay(1), oneway-p2r-delay(2), oneway-r2p-delay(3), oneway-p2r-jitter(4), oneway-r2p-jitter(5), oneway-p2r-absjitter(6), oneway-r2p-absjitter(7), roundtrip-absjitter(8), oneway-p2r-fdr(9), oneway-r2p-fdr(10), roundtrip-fdr(11)

EsaAction
ESA Scheduled Group/Reflector Action.
TEXTUAL-CONVENTION
	INTEGER	not-applicable(0), suspend(1), resume(2), addEsaProbe(3), removeEsaProbe(4)

EsaProbePktIntervalType
Interval Type used for LMM and DMM messages.
TEXTUAL-CONVENTION
	INTEGER	not-applicable(0), interval-10ms(1), interval-100ms(2), interval-1sec(3), interval-10sec(4), interval-1min(5)

EsaProbeSLAMonitorType
ESA Probe SLA Monitor Type.
TEXTUAL-CONVENTION
	INTEGER	not-applicable(0), point-to-point(1), point-to-multipoint(2)

BerTestStatus
BER Test Status.
TEXTUAL-CONVENTION
	INTEGER	not-applicable(0), running(1), not-running(2)

BerTestMode
BER Test Control Test Mode.
TEXTUAL-CONVENTION
	INTEGER	not-applicable(0), generator(1), monitor(2), singleend(3)

BertControlAction
BER Test Control Action.
TEXTUAL-CONVENTION
	INTEGER	not-applicable(0), start(1), stop(2)

BertPattern
BERT Tx Pattern.
TEXTUAL-CONVENTION
	INTEGER	not-applicable(0), all-0(1), all-1(2), alt-1100(3), bit-1in8(4), bit-3in24(5), bit-2exp20-qrss(6), bit-2exp11-prbs(7), bit-2exp15-prbs(8), bit-2exp23-prbs(9), userdefined(10)

BertUserPatternLength
BERT Error Rate.
TEXTUAL-CONVENTION
	INTEGER	not-applicable(0), length-1byte(1), length-2byte(2), length-3byte(3), length-4byte(4)

BertSyncState
BERT Sync State.
TEXTUAL-CONVENTION
	INTEGER	not-applicable(0), sync(1), outofsync(2)

EcpaControlEntry
SEQUENCE
	ecpaControlIndex	Integer32
	ecpaControlSourcePort	VariablePointer
	ecpaControlTestType	EcpaTestType
	ecpaControlNumFrames	Integer32
	ecpaControlDuration	Integer32
	ecpaControlInjectorDirection	TrafficDirection
	ecpaControlMonitorDirection	TrafficDirection
	ecpaControlStream1	Integer32
	ecpaControlStream2	Integer32
	ecpaControlStream3	Integer32
	ecpaControlAction	EcpaControlAction
	ecpaControlTestStatus	EcpaTestStatus
	ecpaControlStorageType	StorageType
	ecpaControlRowStatus	RowStatus

EcpaConfigStreamEntry
SEQUENCE
	ecpaConfigStreamIndex	Integer32
	ecpaConfigStreamName	DisplayString
	ecpaConfigStreamFrameSize	Integer32
	ecpaConfigStreamRate	Unsigned32
	ecpaConfigStreamPayloadType	EcpaPayloadType
	ecpaConfigStreamSignature	DisplayString
	ecpaConfigStreamDestinationMAC	MacAddress
	ecpaConfigStreamSourceMAC	MacAddress
	ecpaConfigStreamOuterVlanEnabled	TruthValue
	ecpaConfigStreamOuterVlanId	VlanId
	ecpaConfigStreamOuterVlanPrio	VlanPriority
	ecpaConfigStreamOuterVlanEtherType	Integer32
	ecpaConfigStreamInnerVlanEnabled	TruthValue
	ecpaConfigStreamInnerVlanId	VlanId
	ecpaConfigStreamInnerVlanPrio	VlanPriority
	ecpaConfigStreamInnerVlanEtherType	Integer32
	ecpaConfigStreamIpVersion	IpVersion
	ecpaConfigStreamIpV4Address	IpAddress
	ecpaConfigStreamIpV6Address	Ipv6Address
	ecpaConfigStreamPrioMapMode	IpPriorityMapMode
	ecpaConfigStreamPrioVal	Integer32
	ecpaConfigStreamInnerVlan2Enabled	TruthValue
	ecpaConfigStreamInnerVlan2Id	VlanId
	ecpaConfigStreamInnerVlan2Prio	VlanPriority
	ecpaConfigStreamInnerVlan2EtherType	Integer32
	ecpaConfigStreamDestIpV4Address	IpAddress
	ecpaConfigStreamDestIpV6Address	Ipv6Address
	ecpaConfigStreamUsePortSourceMAC	TruthValue
	ecpaConfigStreamRateHi	Unsigned32

EcpaTestStreamEntry
SEQUENCE
	ecpaTestStreamIndex	Integer32
	ecpaTestStreamSourcePort	VariablePointer
	ecpaTestStreamName	DisplayString
	ecpaTestStreamFrameSize	Integer32
	ecpaTestStreamRate	Unsigned32
	ecpaTestStreamPayloadType	EcpaPayloadType
	ecpaTestStreamSignature	DisplayString
	ecpaTestStreamDestinationMAC	MacAddress
	ecpaTestStreamSourceMAC	MacAddress
	ecpaTestStreamOuterVlanEnabled	TruthValue
	ecpaTestStreamOuterVlanId	VlanId
	ecpaTestStreamOuterVlanPrio	VlanPriority
	ecpaTestStreamOuterVlanEtherType	Integer32
	ecpaTestStreamInnerVlanEnabled	TruthValue
	ecpaTestStreamInnerVlanId	VlanId
	ecpaTestStreamInnerVlanPrio	VlanPriority
	ecpaTestStreamInnerVlanEtherType	Integer32
	ecpaTestStreamIpVersion	IpVersion
	ecpaTestStreamIpV4Address	IpAddress
	ecpaTestStreamIpV6Address	Ipv6Address
	ecpaTestStreamPrioMapMode	IpPriorityMapMode
	ecpaTestStreamPrioVal	Integer32
	ecpaTestStreamMonStartTime	DateAndTime
	ecpaTestStreamMonEndTime	DateAndTime
	ecpaTestStreamMonElapsedTime	Integer32
	ecpaTestStreamMonTxFrames	PerfCounter64
	ecpaTestStreamMonRxFrames	PerfCounter64
	ecpaTestStreamMonRxPercentSuccess	Integer32
	ecpaTestStreamMonRxOutOfSeqErrs	PerfCounter64
	ecpaTestStreamMonRxSeqGaps	PerfCounter64
	ecpaTestStreamMonRxNonEcpaFrames	PerfCounter64
	ecpaTestStreamMonRxMinDelay	Unsigned32
	ecpaTestStreamMonRxMaxDelay	Unsigned32
	ecpaTestStreamMonRxAvgDelay	Unsigned32
	ecpaTestStreamMonRx1stFrameSize	Integer32
	ecpaTestStreamMonRx1stFrame1Octets	DisplayString
	ecpaTestStreamMonRx1stFrame2Octets	DisplayString
	ecpaTestStreamMonRx1stFrame3Octets	DisplayString
	ecpaTestStreamMonRx1stFrame4Octets	DisplayString
	ecpaTestStreamMonRx1stFrame5Octets	DisplayString
	ecpaTestStreamMonRx1stFrame6Octets	DisplayString
	ecpaTestStreamMonRx1stFrame7Octets	DisplayString
	ecpaTestStreamMonRx1stFrame8Octets	DisplayString
	ecpaTestStreamMonRx1stFrame9Octets	DisplayString
	ecpaTestStreamMonRx1stFrame10Octets	DisplayString
	ecpaTestStreamMonRxBitRate	PerfCounter64
	ecpaTestStreamInnerVlan2Enabled	TruthValue
	ecpaTestStreamInnerVlan2Id	VlanId
	ecpaTestStreamInnerVlan2Prio	VlanPriority
	ecpaTestStreamInnerVlan2EtherType	Integer32
	ecpaTestStreamDestIpV4Address	IpAddress
	ecpaTestStreamDestIpV6Address	Ipv6Address
	ecpaTestStreamConfigChanged	TruthValue
	ecpaTestStreamRateHi	Unsigned32

EsaProbeEntry
SEQUENCE
	esaProbeIndex	Integer32
	esaProbeName	DisplayString
	esaProbeSourcePort	VariablePointer
	esaProbeAssocSchedGroup	VariablePointer
	esaProbeDirection	EsaProbeDirection
	esaProbeProtocol	EsaProbeProtocol
	esaProbeSrcIpAddress	IpAddress
	esaProbeSrcSubnetMask	IpAddress
	esaProbeDestIpAddress	IpAddress
	esaProbeSrcMep	VariablePointer
	esaProbeDestMepType	MepDestinationType
	esaProbeDestMepMacAddr	MacAddress
	esaProbeDestMepId	Dot1agCfmMepIdOrZero
	esaProbeVlanTagEnabled	TruthValue
	esaProbeVlanTagEtherType	Unsigned32
	esaProbeVlanId	VlanId
	esaProbeVlanPrio	VlanPriority
	esaProbeInnerVlanTagEnabled	TruthValue
	esaProbeInnerVlanTagEtherType	Unsigned32
	esaProbeInnerVlanId	VlanId
	esaProbeInnerVlanPrio	VlanPriority
	esaProbeIpPrioMapMode	IpPriorityMapMode
	esaProbeIpPriority	Integer32
	esaProbePktsPerSample	Integer32
	esaProbePktSize	Integer32
	esaProbeInterPktGap	Integer32
	esaProbePktDeadInterval	Integer32
	esaProbeResponseTimeout	Integer32
	esaProbeY1731DmmPktSize	Integer32
	esaProbeY1731LmmInterval	EsaProbePktIntervalType
	esaProbeY1731DmmInterval	EsaProbePktIntervalType
	esaProbeHistoryBins	Integer32
	esaProbeHistoryInterval	EsaProbeHistoryIntervalType
	esaProbeDistHistoryBins	Integer32
	esaProbeDistHistoryInterval	EsaProbeHistoryIntervalType
	esaProbeCreationTime	DateAndTime
	esaProbeStorageType	StorageType
	esaProbeRowStatus	RowStatus
	esaProbeMultiCOSEnabled	TruthValue
	esaProbeSLAMonitorType	EsaProbeSLAMonitorType
	esaProbeCOSType	ClassOfServiceType
	esaProbeSLMMulticastMACEnabled	TruthValue
	esaProbeSOAMInterval	EsaProbePktIntervalType
	esaProbeSOAMPktSize	Integer32
	esaProbeInner2VlanTagEnabled	TruthValue
	esaProbeInner2VlanTagEtherType	Unsigned32
	esaProbeInner2VlanId	VlanId
	esaProbeInner2VlanPrio	VlanPriority
	esaProbeAdminState	AdminState
	esaProbeOperationalState	OperationalState
	esaProbeSecondaryState	SecondaryState
	esaProbeMacAddress	MacAddress
	esaProbeAlias	DisplayString

EsaProbeScheduleGroupEntry
SEQUENCE
	esaProbeScheduleGroupIndex	Integer32
	esaProbeScheduleGroupDescr	DisplayString
	esaProbeScheduleGroupProbeList	DisplayString
	esaProbeScheduleGroupType	ScheduleType
	esaProbeScheduleGroupStartTime	DateAndTime
	esaProbeScheduleGroupDuration	Unsigned32
	esaProbeScheduleGroupInterval	Unsigned32
	esaProbeScheduleGroupAction	EsaAction
	esaProbeScheduleGroupStatus	SchedActivityStatus
	esaProbeScheduleGroupStorageType	StorageType
	esaProbeScheduleGroupRowStatus	RowStatus
	esaProbeScheduleGroupActionProbeList	DisplayString

EsaReflectorEntry
SEQUENCE
	esaReflectorIndex	Integer32
	esaReflectorName	DisplayString
	esaReflectorIpAddress	IpAddress
	esaReflectorSubnetMask	IpAddress
	esaReflectorSourcePort	VariablePointer
	esaReflectorIpPrioMapMode	IpPriorityMapMode
	esaReflectorIpPriority	Integer32
	esaReflectorAction	EsaAction
	esaReflectorSuspended	TruthValue
	esaReflectorCreationTime	DateAndTime
	esaReflectorStorageType	StorageType
	esaReflectorRowStatus	RowStatus
	esaReflectorDirection	EsaReflectorDirection
	esaReflectorAdminState	AdminState
	esaReflectorOperationalState	OperationalState
	esaReflectorSecondaryState	SecondaryState
	esaReflectorMacAddress	MacAddress
	esaReflectorAlias	DisplayString

EsaProbeStatsEntry
SEQUENCE
	esaProbeStatsDestinationIndex	Integer32
	esaProbeStatsCOSIndex	Integer32
	esaProbeStatsIndex	Integer32
	esaProbeStatsIntervalType	EsaProbePmIntervalType
	esaProbeStatsCOS	ClassOfServiceType
	esaProbeStatsValid	TruthValue
	esaProbeStatsAction	CmPmBinAction
	esaProbeStatsP2RPkts	PerfCounter64
	esaProbeStatsP2RErredPkts	PerfCounter64
	esaProbeStatsP2RSyncErrs	PerfCounter64
	esaProbeStatsP2RLostPkts	PerfCounter64
	esaProbeStatsR2PPkts	PerfCounter64
	esaProbeStatsR2PErredPkts	PerfCounter64
	esaProbeStatsR2PSyncErrs	PerfCounter64
	esaProbeStatsR2PLostPkts	PerfCounter64
	esaProbeStatsLostPkts	PerfCounter64
	esaProbeStatsSeqGaps	PerfCounter64
	esaProbeStatsOutOfSeqErrs	PerfCounter64
	esaProbeStatsMinRoundTripDelay	Unsigned32
	esaProbeStatsMaxRoundTripDelay	Unsigned32
	esaProbeStatsAvgRoundTripDelay	Unsigned32
	esaProbeStatsSumRoundTripDelay	PerfCounter64
	esaProbeStatsSumOfSqRoundTripDelay	PerfCounter64
	esaProbeStatsMinOnewayP2RDelay	Unsigned32
	esaProbeStatsMaxOnewayP2RDelay	Unsigned32
	esaProbeStatsAvgOnewayP2RDelay	Unsigned32
	esaProbeStatsSumOnewayP2RDelay	PerfCounter64
	esaProbeStatsSumOfSqOnewayP2RDelay	PerfCounter64
	esaProbeStatsMinOnewayR2PDelay	Unsigned32
	esaProbeStatsMaxOnewayR2PDelay	Unsigned32
	esaProbeStatsAvgOnewayR2PDelay	Unsigned32
	esaProbeStatsSumOnewayR2PDelay	PerfCounter64
	esaProbeStatsSumOfSqOnewayR2PDelay	PerfCounter64
	esaProbeStatsMinPosP2RJitter	Unsigned32
	esaProbeStatsMaxPosP2RJitter	Unsigned32
	esaProbeStatsNumPosP2RJitter	PerfCounter64
	esaProbeStatsSumPosP2RJitter	PerfCounter64
	esaProbeStatsSumOfSqPosP2RJitter	PerfCounter64
	esaProbeStatsMinNegP2RJitter	Unsigned32
	esaProbeStatsMaxNegP2RJitter	Unsigned32
	esaProbeStatsNumNegP2RJitter	PerfCounter64
	esaProbeStatsSumNegP2RJitter	PerfCounter64
	esaProbeStatsSumOfSqNegP2RJitter	PerfCounter64
	esaProbeStatsMinPosR2PJitter	Unsigned32
	esaProbeStatsMaxPosR2PJitter	Unsigned32
	esaProbeStatsNumPosR2PJitter	PerfCounter64
	esaProbeStatsSumPosR2PJitter	PerfCounter64
	esaProbeStatsSumOfSqPosR2PJitter	PerfCounter64
	esaProbeStatsMinNegR2PJitter	Unsigned32
	esaProbeStatsMaxNegR2PJitter	Unsigned32
	esaProbeStatsNumNegR2PJitter	PerfCounter64
	esaProbeStatsSumNegR2PJitter	PerfCounter64
	esaProbeStatsSumOfSqNegR2PJitter	PerfCounter64
	esaProbeStatsY1731P2RNegLossOccurrences	PerfCounter64
	esaProbeStatsY1731R2PNegLossOccurrences	PerfCounter64
	esaProbeStatsY1731RxLmSamples	TruthValue
	esaProbeStatsY1731RxDmSamples	TruthValue
	esaProbeStatsY1731P2RFrames	PerfCounter64
	esaProbeStatsY1731R2PFrames	PerfCounter64
	esaProbeStatsAvgAbsP2RJitter	Unsigned32
	esaProbeStatsAvgAbsR2PJitter	Unsigned32
	esaProbeStatsMaxAbsP2RJitter	Unsigned32
	esaProbeStatsMaxAbsR2PJitter	Unsigned32
	esaProbeStatsMinAbsP2RJitter	Unsigned32
	esaProbeStatsMinAbsR2PJitter	Unsigned32
	esaProbeStatsNumAbsP2RJitter	PerfCounter64
	esaProbeStatsNumAbsR2PJitter	PerfCounter64
	esaProbeStatsSumAbsP2RJitter	PerfCounter64
	esaProbeStatsSumAbsR2PJitter	PerfCounter64
	esaProbeStatsSumOfSqAbsP2RJitter	PerfCounter64
	esaProbeStatsSumOfSqAbsR2PJitter	PerfCounter64

EsaProbeHistoryEntry
SEQUENCE
	esaProbeHistoryDestinationIndex	Integer32
	esaProbeHistoryCOSIndex	Integer32
	esaProbeHistoryIndex	Integer32
	esaProbeHistoryTime	DateAndTime
	esaProbeHistoryValid	TruthValue
	esaProbeHistoryAction	CmPmBinAction
	esaProbeHistoryCOS	ClassOfServiceType
	esaProbeHistoryP2RPkts	PerfCounter64
	esaProbeHistoryP2RErredPkts	PerfCounter64
	esaProbeHistoryP2RSyncErrs	PerfCounter64
	esaProbeHistoryP2RLostPkts	PerfCounter64
	esaProbeHistoryR2PPkts	PerfCounter64
	esaProbeHistoryR2PErredPkts	PerfCounter64
	esaProbeHistoryR2PSyncErrs	PerfCounter64
	esaProbeHistoryR2PLostPkts	PerfCounter64
	esaProbeHistoryLostPkts	PerfCounter64
	esaProbeHistorySeqGaps	PerfCounter64
	esaProbeHistoryOutOfSeqErrs	PerfCounter64
	esaProbeHistoryMinRoundTripDelay	Unsigned32
	esaProbeHistoryMaxRoundTripDelay	Unsigned32
	esaProbeHistoryAvgRoundTripDelay	Unsigned32
	esaProbeHistorySumRoundTripDelay	PerfCounter64
	esaProbeHistorySumOfSqRoundTripDelay	PerfCounter64
	esaProbeHistoryMinOnewayP2RDelay	Unsigned32
	esaProbeHistoryMaxOnewayP2RDelay	Unsigned32
	esaProbeHistoryAvgOnewayP2RDelay	Unsigned32
	esaProbeHistorySumOnewayP2RDelay	PerfCounter64
	esaProbeHistorySumOfSqOnewayP2RDelay	PerfCounter64
	esaProbeHistoryMinOnewayR2PDelay	Unsigned32
	esaProbeHistoryMaxOnewayR2PDelay	Unsigned32
	esaProbeHistoryAvgOnewayR2PDelay	Unsigned32
	esaProbeHistorySumOnewayR2PDelay	PerfCounter64
	esaProbeHistorySumOfSqOnewayR2PDelay	PerfCounter64
	esaProbeHistoryMinPosP2RJitter	Unsigned32
	esaProbeHistoryMaxPosP2RJitter	Unsigned32
	esaProbeHistoryNumPosP2RJitter	PerfCounter64
	esaProbeHistorySumPosP2RJitter	PerfCounter64
	esaProbeHistorySumOfSqPosP2RJitter	PerfCounter64
	esaProbeHistoryMinNegP2RJitter	Unsigned32
	esaProbeHistoryMaxNegP2RJitter	Unsigned32
	esaProbeHistoryNumNegP2RJitter	PerfCounter64
	esaProbeHistorySumNegP2RJitter	PerfCounter64
	esaProbeHistorySumOfSqNegP2RJitter	PerfCounter64
	esaProbeHistoryMinPosR2PJitter	Unsigned32
	esaProbeHistoryMaxPosR2PJitter	Unsigned32
	esaProbeHistoryNumPosR2PJitter	PerfCounter64
	esaProbeHistorySumPosR2PJitter	PerfCounter64
	esaProbeHistorySumOfSqPosR2PJitter	PerfCounter64
	esaProbeHistoryMinNegR2PJitter	Unsigned32
	esaProbeHistoryMaxNegR2PJitter	Unsigned32
	esaProbeHistoryNumNegR2PJitter	PerfCounter64
	esaProbeHistorySumNegR2PJitter	PerfCounter64
	esaProbeHistorySumOfSqNegR2PJitter	PerfCounter64
	esaProbeHistoryY1731P2RNegLossOccurrences	PerfCounter64
	esaProbeHistoryY1731R2PNegLossOccurrences	PerfCounter64
	esaProbeHistoryY1731RxLmSamples	TruthValue
	esaProbeHistoryY1731RxDmSamples	TruthValue
	esaProbeHistoryY1731P2RFrames	PerfCounter64
	esaProbeHistoryY1731R2PFrames	PerfCounter64
	esaProbeHistoryAvgAbsP2RJitter	Unsigned32
	esaProbeHistoryAvgAbsR2PJitter	Unsigned32
	esaProbeHistoryMaxAbsP2RJitter	Unsigned32
	esaProbeHistoryMaxAbsR2PJitter	Unsigned32
	esaProbeHistoryMinAbsP2RJitter	Unsigned32
	esaProbeHistoryMinAbsR2PJitter	Unsigned32
	esaProbeHistoryNumAbsP2RJitter	PerfCounter64
	esaProbeHistoryNumAbsR2PJitter	PerfCounter64
	esaProbeHistorySumAbsP2RJitter	PerfCounter64
	esaProbeHistorySumAbsR2PJitter	PerfCounter64
	esaProbeHistorySumOfSqAbsP2RJitter	PerfCounter64
	esaProbeHistorySumOfSqAbsR2PJitter	PerfCounter64

EsaProbeDistStatsConfigEntry
SEQUENCE
	esaProbeDistStatsConfigIndex	Integer32
	esaProbeDistStatsConfigType	EsaProbeDistStatsType
	esaProbeDistStatsConfigMinVal	Integer32
	esaProbeDistStatsConfigMaxVal	Integer32
	esaProbeDistStatsConfigNumBins	Unsigned32
	esaProbeDistStatsConfigLowBoundOfBin1	Integer32
	esaProbeDistStatsConfigLowBoundOfBin2	Integer32
	esaProbeDistStatsConfigLowBoundOfBin3	Integer32
	esaProbeDistStatsConfigLowBoundOfBin4	Integer32
	esaProbeDistStatsConfigLowBoundOfBin5	Integer32
	esaProbeDistStatsConfigLowBoundOfBin6	Integer32
	esaProbeDistStatsConfigLowBoundOfBin7	Integer32
	esaProbeDistStatsConfigLowBoundOfBin8	Integer32
	esaProbeDistStatsConfigLowBoundOfBin9	Integer32

EsaProbeDistStatsEntry
SEQUENCE
	esaProbeDistStatsDestinationIndex	Integer32
	esaProbeDistStatsCOSIndex	Integer32
	esaProbeDistStatsAction	CmPmBinAction
	esaProbeDistStatsCOS	ClassOfServiceType
	esaProbeDistStatsNumBins	Integer32
	esaProbeDistStatsLTMin	PerfCounter64
	esaProbeDistStatsGTMax	PerfCounter64

EsaProbeDistStatsBinEntry
SEQUENCE
	esaProbeDistStatsBinIndex	Integer32
	esaProbeDistStatsBinLower	Integer32
	esaProbeDistStatsBinUpper	Integer32
	esaProbeDistStatsBinNumSamples	PerfCounter64

EsaProbeDistHistoryEntry
SEQUENCE
	esaProbeDistHistoryDestinationIndex	Integer32
	esaProbeDistHistoryCOSIndex	Integer32
	esaProbeDistHistoryIndex	Integer32
	esaProbeDistHistoryTime	DateAndTime
	esaProbeDistHistoryAction	CmPmBinAction
	esaProbeDistHistoryCOS	ClassOfServiceType
	esaProbeDistHistoryNumBins	Integer32
	esaProbeDistHistoryLTMin	PerfCounter64
	esaProbeDistHistoryGTMax	PerfCounter64

EsaProbeDistHistoryBinEntry
SEQUENCE
	esaProbeDistHistoryBinIndex	Integer32
	esaProbeDistHistoryBinLower	Integer32
	esaProbeDistHistoryBinUpper	Integer32
	esaProbeDistHistoryBinNumSamples	PerfCounter64

EsaProbeStatsThresholdEntry
SEQUENCE
	esaProbeStatsThresholdIndex	Integer32
	esaProbeStatsThresholdVariable	VariablePointer
	esaProbeStatsThresholdAbsValueLo	Unsigned32
	esaProbeStatsThresholdAbsValueHi	Unsigned32
	esaProbeStatsThresholdMonValue	PerfCounter64

EsaProbeCOSConfigEntry
SEQUENCE
	esaProbeCOSConfigIndex	Integer32
	esaProbeCOSConfigType	ClassOfServiceType
	esaProbeCOSConfigInterval	EsaProbePktIntervalType
	esaProbeCOSConfigPktSize	Integer32
	esaProbeCOSConfigStorageType	StorageType
	esaProbeCOSConfigRowStatus	RowStatus
	esaProbeCOSConfigslmInterval	EsaProbePktIntervalType
	esaProbeCOSConfigslmPktSize	Integer32
	esaProbeCOSConfigSoamPmExtAvailFlrThreshold	Unsigned32
	esaProbeCOSConfigSoamPmExtFlrDeltaTNumLmPdus	Unsigned32
	esaProbeCOSConfigSoamPmExtConDeltaTsForAvail	Unsigned32

EsaProbeMultiDestinationEntry
SEQUENCE
	esaProbeDestinationIndex	Integer32
	esaProbeDestinationMepType	MepDestinationType
	esaProbeDestinationMepMacAddr	MacAddress
	esaProbeDestinationMepId	Dot1agCfmMepIdOrZero
	esaProbeDestinationStorageType	StorageType
	esaProbeDestinationRowStatus	RowStatus

BertControlEntry
SEQUENCE
	bertControlIndex	Integer32
	bertControlSourceEntity	VariablePointer
	bertControlTestMode	BerTestMode
	bertControlDuration	Integer32
	bertControlStream	Integer32
	bertControlAction	BertControlAction
	bertControlTestStatus	BerTestStatus

BertConfigStreamEntry
SEQUENCE
	bertConfigStreamIndex	Integer32
	bertConfigStreamName	DisplayString
	bertConfigStreamTxPattern	BertPattern
	bertConfigStreamErrInjectEnabled	TruthValue
	bertConfigStreamErrInjectRate	BitErrRate
	bertConfigStreamErrInjectRateMultiplier	Integer32
	bertConfigStreamUserPatternLength	BertUserPatternLength
	bertConfigStreamUserPattern	DisplayString

BertTestStreamEntry
SEQUENCE
	bertTestStreamIndex	Integer32
	bertTestStreamName	DisplayString
	bertTestStreamTxPattern	BertPattern
	bertTestStreamErrInjectEnabled	TruthValue
	bertTestStreamErrInjectRate	BitErrRate
	bertTestStreamErrInjectRateMultiplier	Integer32
	bertTestStreamUserPatternLength	BertUserPatternLength
	bertTestStreamUserPattern	DisplayString
	bertTestStreamMonStartTime	DateAndTime
	bertTestStreamMonEndTime	DateAndTime
	bertTestStreamMonElapsedTime	Integer32
	bertTestStreamMonSyncState	BertSyncState
	bertTestStreamMonRxPattern	BertPattern
	bertTestStreamMonSyncCounts	Unsigned32
	bertTestStreamMonRxBitErrsSinceStart	PerfCounter64
	bertTestStreamMonRxBitsSinceStart	PerfCounter64
	bertTestStreamMonRxESsSinceStart	Unsigned32
	bertTestStreamMonRxErrRateSinceStart	BitErrRate
	bertTestStreamMonRxErrRateMultiplierSinceStart	Integer32
	bertTestStreamMonRxBitErrsSinceLastSync	PerfCounter64
	bertTestStreamMonRxBitsSinceLastSync	PerfCounter64
	bertTestStreamMonRxESsSinceLastSync	Unsigned32
	bertTestStreamMonRxErrRateSinceLastSync	BitErrRate
	bertTestStreamMonRxErrRateMultiplierSinceLastSync	Unsigned32
	bertTestStreamConfigChangedFlag	TruthValue
	bertTestStreamMonOOSSsSinceStart	Unsigned32

F3EsaProbeCOSConfigSoamPmExtEntry
SEQUENCE
	f3EsaProbeCOSConfigSoamPmExtAvailFlrThreshold	Unsigned32
	f3EsaProbeCOSConfigSoamPmExtFlrDeltaTNumLmPdus	Unsigned32
	f3EsaProbeCOSConfigSoamPmExtConDeltaTsForAvail	Unsigned32

F3EsaProbeStatsSoamPmExtEntry
SEQUENCE
	f3EsaProbeStatsSoamPmExtMinP2RFlr	PerfCounter64
	f3EsaProbeStatsSoamPmExtMaxP2RFlr	PerfCounter64
	f3EsaProbeStatsSoamPmExtAvgP2RFlr	PerfCounter64
	f3EsaProbeStatsSoamPmExtMinR2PFlr	PerfCounter64
	f3EsaProbeStatsSoamPmExtMaxR2PFlr	PerfCounter64
	f3EsaProbeStatsSoamPmExtAvgR2PFlr	PerfCounter64
	f3EsaProbeStatsSoamPmExtP2rSeverelyErroredDeltaTs	PerfCounter64
	f3EsaProbeStatsSoamPmExtR2PSeverelyErroredDeltaTs	PerfCounter64
	f3EsaProbeStatsSoamPmExtP2rAvailableTime	PerfCounter64
	f3EsaProbeStatsSoamPmExtR2PAvailableTime	PerfCounter64
	f3EsaProbeStatsSoamPmExtP2rUnavailableTime	PerfCounter64
	f3EsaProbeStatsSoamPmExtR2PUnavailableTime	PerfCounter64
	f3EsaProbeStatsSoamPmExtMinAbsRTJitter	PerfCounter64
	f3EsaProbeStatsSoamPmExtMaxAbsRTJitter	PerfCounter64
	f3EsaProbeStatsSoamPmExtAvgAbsRTJitter	PerfCounter64
	f3EsaProbeStatsSoamPmExtNumAbsRTJitter	PerfCounter64
	f3EsaProbeStatsSoamPmExtSumAbsRTJitter	PerfCounter64
	f3EsaProbeStatsSoamPmExtSumOfSqAbsRTJitter	PerfCounter64
	f3EsaProbeStatsSoamPmExtMaxP2RFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtAvgP2RFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtNumP2RFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtSumP2RFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtSumOfSqP2RFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtMaxR2PFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtAvgR2PFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtNumR2PFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtSumR2PFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtSumOfSqR2PFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtMaxRTFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtAvgRTFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtNumRTFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtSumRTFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtSumOfSqRTFDR	PerfCounter64
	f3EsaProbeStatsSoamPmExtP2rAvailableDeltaTs	PerfCounter64
	f3EsaProbeStatsSoamPmExtR2pAvailableDeltaTs	PerfCounter64
	f3EsaProbeStatsSoamPmExtP2rUnavailableDeltaTs	PerfCounter64
	f3EsaProbeStatsSoamPmExtR2pUnavailableDeltaTs	PerfCounter64
	f3EsaProbeStatsSoamPmExtElapsedTime	PerfCounter64

F3EsaProbeHistorySoamPmExtEntry
SEQUENCE
	f3EsaProbeHistorySoamPmExtMinP2RFlr	PerfCounter64
	f3EsaProbeHistorySoamPmExtMaxP2RFlr	PerfCounter64
	f3EsaProbeHistorySoamPmExtAvgP2RFlr	PerfCounter64
	f3EsaProbeHistorySoamPmExtMinR2PFlr	PerfCounter64
	f3EsaProbeHistorySoamPmExtMaxR2PFlr	PerfCounter64
	f3EsaProbeHistorySoamPmExtAvgR2PFlr	PerfCounter64
	f3EsaProbeHistorySoamPmExtP2rSeverelyErroredDeltaTs	PerfCounter64
	f3EsaProbeHistorySoamPmExtR2PSeverelyErroredDeltaTs	PerfCounter64
	f3EsaProbeHistorySoamPmExtP2rAvailableTime	PerfCounter64
	f3EsaProbeHistorySoamPmExtR2PAvailableTime	PerfCounter64
	f3EsaProbeHistorySoamPmExtP2rUnavailableTime	PerfCounter64
	f3EsaProbeHistorySoamPmExtR2PUnavailableTime	PerfCounter64
	f3EsaProbeHistorySoamPmExtMinAbsRTJitter	PerfCounter64
	f3EsaProbeHistorySoamPmExtMaxAbsRTJitter	PerfCounter64
	f3EsaProbeHistorySoamPmExtAvgAbsRTJitter	PerfCounter64
	f3EsaProbeHistorySoamPmExtNumAbsRTJitter	PerfCounter64
	f3EsaProbeHistorySoamPmExtSumAbsRTJitter	PerfCounter64
	f3EsaProbeHistorySoamPmExtSumOfSqAbsRTJitter	PerfCounter64
	f3EsaProbeHistorySoamPmExtMaxP2RFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtAvgP2RFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtNumP2RFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtSumP2RFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtSumOfSqP2RFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtMaxR2PFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtAvgR2PFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtNumR2PFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtSumR2PFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtSumOfSqR2PFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtMaxRTFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtAvgRTFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtNumRTFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtSumRTFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtSumOfSqRTFDR	PerfCounter64
	f3EsaProbeHistorySoamPmExtP2rAvailableDeltaTs	PerfCounter64
	f3EsaProbeHistorySoamPmExtR2pAvailableDeltaTs	PerfCounter64
	f3EsaProbeHistorySoamPmExtP2rUnavailableDeltaTs	PerfCounter64
	f3EsaProbeHistorySoamPmExtR2pUnavailableDeltaTs	PerfCounter64
	f3EsaProbeHistorySoamPmExtElapsedTime	PerfCounter64

Defined Values

cmServiceAssuranceMIB		1.3.6.1.4.1.2544.1.12.8
This module defines the Service Assurance MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA Optical Networking.
MODULE-IDENTITY

cmServAssuranceObjects		1.3.6.1.4.1.2544.1.12.8.1
OBJECT IDENTIFIER

cmServAssuranceNotifications		1.3.6.1.4.1.2544.1.12.8.2
OBJECT IDENTIFIER

cmServAssuranceConformance		1.3.6.1.4.1.2544.1.12.8.3
OBJECT IDENTIFIER

ecpaControlTable		1.3.6.1.4.1.2544.1.12.8.1.1
A list of entries for the control of Etherjack Connection Performance Analyzer Streams. Upto 12 ECPA streams can be configured per test head; 3 ECPA streams can be simultaneously executed.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EcpaControlEntry

ecpaControlEntry		1.3.6.1.4.1.2544.1.12.8.1.1.1
A conceptual row in the ecpaControlTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	EcpaControlEntry

ecpaControlIndex		1.3.6.1.4.1.2544.1.12.8.1.1.1.1
An arbitrary integer index value used to uniquely identify this Etherjack Connection Performance Analyzer Control Test head. There is only one test head per card.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ecpaControlSourcePort		1.3.6.1.4.1.2544.1.12.8.1.1.1.2
Pointer to the Access or Network Port on which the ECPA test will be started within a card.
Status: current	Access: read-write
OBJECT-TYPE
	VariablePointer

ecpaControlTestType		1.3.6.1.4.1.2544.1.12.8.1.1.1.3
The type of ECPA test to be performed. When 'duration' test is specified, ECPA test is run for 'ecpaControlDuration' time. When 'numFrames' test is specified, ECPA test is run for 'ecpaControlNumFrames', when 'continous' test is specified, ECPA test is run until an explicit 'ecpaControlAction' of 'stop' of received.
Status: current	Access: read-write
OBJECT-TYPE
	EcpaTestType

ecpaControlNumFrames		1.3.6.1.4.1.2544.1.12.8.1.1.1.4
This object enables specification of the number of frames for traffic generation. Traffic Generation will be completed after the specified number of frames are transmitted.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

ecpaControlDuration		1.3.6.1.4.1.2544.1.12.8.1.1.1.5
This object enables specification of the time in seconds for traffic generation. Traffic Generation will be stopped after the specified time interval is exhausted.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..259200

ecpaControlInjectorDirection		1.3.6.1.4.1.2544.1.12.8.1.1.1.6
This object enables specification of the direction of traffic generation. This value must be specified if the interface is used for traffic generation. Both of ecpaControlInjectorDirection and ecpaControlMonitorDirection must be specified.
Status: current	Access: read-write
OBJECT-TYPE
	TrafficDirection

ecpaControlMonitorDirection		1.3.6.1.4.1.2544.1.12.8.1.1.1.7
This object enables specification of the direction of receival of generated traffic. This value must be specified if the interface is used for receiving/monitoring generated traffic. Both of ecpaControlInjectorDirection and ecpaControlMonitorDirection must be specified.
Status: current	Access: read-write
OBJECT-TYPE
	TrafficDirection

ecpaControlStream1		1.3.6.1.4.1.2544.1.12.8.1.1.1.8
This object specifies which stream should be included in the ECPA execution. Value of 0 indicates that no streams is selected by ecpaControlStream1. Non 0 value indicates the selected ECPA stream.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..48

ecpaControlStream2		1.3.6.1.4.1.2544.1.12.8.1.1.1.9
This object specifies which stream should be included in the ECPA execution. Value of 0 indicates that no streams is selected by ecpaControlStream2. Non 0 value indicates the selected ECPA stream.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..48

ecpaControlStream3		1.3.6.1.4.1.2544.1.12.8.1.1.1.10
This object specifies which stream should be included in the ECPA execution. Value of 0 indicates that no streams is selected by ecpaControlStream3. Non 0 value indicates the selected ECPA stream.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..48

ecpaControlAction		1.3.6.1.4.1.2544.1.12.8.1.1.1.11
This object enables starting/stopping of traffic generation as well as resetting of monitored streams. This object may not be specified at configuration creation time - in this case it will take the value of `none'. This allows manager to explicitly control the start and stop of traffic generation/monitoring activity. Value of `stop' is invalid if the activity is specified but not started. Value of `start' is valid during creation time, as well as when activity is already stopped. Specification of `reset' resets the specified streams to default values, as well as clears the control specification. Get on this variable gives the most recent SNMP set specification.
Status: current	Access: read-write
OBJECT-TYPE
	EcpaControlAction

ecpaControlTestStatus		1.3.6.1.4.1.2544.1.12.8.1.1.1.12
This object reflects the current status of test set configuration entry. Upon creation, the status has a value of `initial'; the status changes to `in-progress' upon ecpaControlAction indicating `start'; the status changes to `completed' upon ecpaControlAction indicating stop, as well as when the specified test generation completes autonomously upon completion of number of frames or completion of specified time interval.
Status: current	Access: read-only
OBJECT-TYPE
	EcpaTestStatus

ecpaControlStorageType		1.3.6.1.4.1.2544.1.12.8.1.1.1.13
The type of storage configured for this entry.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

ecpaControlRowStatus		1.3.6.1.4.1.2544.1.12.8.1.1.1.14
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of ecpaControlRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with ecpaControlRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The ecpaControlRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

ecpaConfigStreamTable		1.3.6.1.4.1.2544.1.12.8.1.2
A list of entries for the configuration of Etherjack Connection Performance Analyzer Stream Specifications.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EcpaConfigStreamEntry

ecpaConfigStreamEntry		1.3.6.1.4.1.2544.1.12.8.1.2.1
A conceptual row in the ecpaConfigStreamTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	EcpaConfigStreamEntry

ecpaConfigStreamIndex		1.3.6.1.4.1.2544.1.12.8.1.2.1.1
An arbitrary integer index value used to uniquely identify this Etherjack Connection Performance Analyzer.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..48

ecpaConfigStreamName		1.3.6.1.4.1.2544.1.12.8.1.2.1.2
Symbolic Stream Name that can be associated with an ECPA stream.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

ecpaConfigStreamFrameSize		1.3.6.1.4.1.2544.1.12.8.1.2.1.3
This object enables specification of fixed length frame size in bytes for traffic generation. If not specified, default value of 64 bytes is used. CM Aggregation Product limits the upper range value to 9600.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	64..9612

ecpaConfigStreamRate		1.3.6.1.4.1.2544.1.12.8.1.2.1.4
The object enables specification of the traffic generation rate.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

ecpaConfigStreamPayloadType		1.3.6.1.4.1.2544.1.12.8.1.2.1.5
This object enables specification of type of payload to generate `fixed' type indicates a generation pattern of 5A, A5, 5A, A5 bytes. `random' type indicates traffic generation with pseudo-random pattern.
Status: current	Access: read-write
OBJECT-TYPE
	EcpaPayloadType

ecpaConfigStreamSignature		1.3.6.1.4.1.2544.1.12.8.1.2.1.6
Indicates an 8-byte signature specified by the user in hexadecimal or ASCII format. This signature is currently used by the FSP150Mx products for test frame recognition and will be appended directly after the ECPA Signature in the test frame and be 4-byte aligned. This will allow the F3 ECPA feature to interoperate with the existing FSP150Mx products. Hexadecimal signature must be prefixed with 0x/0X.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

ecpaConfigStreamDestinationMAC		1.3.6.1.4.1.2544.1.12.8.1.2.1.7
Allows specification of destination MAC in the generated traffic.
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

ecpaConfigStreamSourceMAC		1.3.6.1.4.1.2544.1.12.8.1.2.1.8
Allows specification of source MAC in the generated traffic.
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

ecpaConfigStreamOuterVlanEnabled		1.3.6.1.4.1.2544.1.12.8.1.2.1.9
Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly tagged ECPA stream is desired, this specification is mandatory.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

ecpaConfigStreamOuterVlanId		1.3.6.1.4.1.2544.1.12.8.1.2.1.10
Outer VLAN Id associated with the ECPA stream. Valid only if ecpaConfigStreamOuterVlanEnabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	VlanId

ecpaConfigStreamOuterVlanPrio		1.3.6.1.4.1.2544.1.12.8.1.2.1.11
Outer VLAN Priority associated with the ECPA stream. Valid only if ecpaConfigStreamOuterVlanEnabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	VlanPriority

ecpaConfigStreamOuterVlanEtherType		1.3.6.1.4.1.2544.1.12.8.1.2.1.12
EtherType associated with the Outer VLAN Tag. Valid only if ecpaConfigStreamOuterVlanEnabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ecpaConfigStreamInnerVlanEnabled		1.3.6.1.4.1.2544.1.12.8.1.2.1.13
Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly tagged ECPA stream is desired, this specification is mandatory.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

ecpaConfigStreamInnerVlanId		1.3.6.1.4.1.2544.1.12.8.1.2.1.14
Inner VLAN Id associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlanEnabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	VlanId

ecpaConfigStreamInnerVlanPrio		1.3.6.1.4.1.2544.1.12.8.1.2.1.15
Inner VLAN Priority associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlanEnabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	VlanPriority

ecpaConfigStreamInnerVlanEtherType		1.3.6.1.4.1.2544.1.12.8.1.2.1.16
EtherType associated with the Inner VLAN Tag. Valid only if ecpaConfigStreamInnerVlanEnabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ecpaConfigStreamIpVersion		1.3.6.1.4.1.2544.1.12.8.1.2.1.17
This object enables specification of IP data in the generated test traffic. Value of `ipv4' allows test data to be IP v4 compatible. Value of `ipv6' allows test data to be IP v6 compatible.
Status: current	Access: read-write
OBJECT-TYPE
	IpVersion

ecpaConfigStreamIpV4Address		1.3.6.1.4.1.2544.1.12.8.1.2.1.18
This object enables specification of ipv4 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv4.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ecpaConfigStreamIpV6Address		1.3.6.1.4.1.2544.1.12.8.1.2.1.19
This object enables specification of ipv6 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv6.
Status: current	Access: read-write
OBJECT-TYPE
	Ipv6Address

ecpaConfigStreamPrioMapMode		1.3.6.1.4.1.2544.1.12.8.1.2.1.20
This object enables specification of Priority Mapping Mode for the test stream.
Status: current	Access: read-write
OBJECT-TYPE
	IpPriorityMapMode

ecpaConfigStreamPrioVal		1.3.6.1.4.1.2544.1.12.8.1.2.1.21
This object enables specification of Priority Value for ecpaConfigStreamPrioMapMode as TOS/DSCP.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..63

ecpaConfigStreamInnerVlan2Enabled		1.3.6.1.4.1.2544.1.12.8.1.2.1.22
Allows specification of a VLAN tagged ECPA stream. This variable enables the second(inner) VLAN specification, in the case of a 3-tagged ECPA stream. If a three tagged ECPA stream is desired, this specification is mandatory.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

ecpaConfigStreamInnerVlan2Id		1.3.6.1.4.1.2544.1.12.8.1.2.1.23
Inner (second) VLAN Id associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlan2Enabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	VlanId

ecpaConfigStreamInnerVlan2Prio		1.3.6.1.4.1.2544.1.12.8.1.2.1.24
Inner (second) VLAN Priority associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlan2Enabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	VlanPriority

ecpaConfigStreamInnerVlan2EtherType		1.3.6.1.4.1.2544.1.12.8.1.2.1.25
EtherType associated with the Inner (second) VLAN Tag. Valid only if ecpaConfigStreamInnerVlan2Enabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ecpaConfigStreamDestIpV4Address		1.3.6.1.4.1.2544.1.12.8.1.2.1.26
This object enables specification of destination ipv4 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv4.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ecpaConfigStreamDestIpV6Address		1.3.6.1.4.1.2544.1.12.8.1.2.1.27
This object enables specification of destination ipv6 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv6.
Status: current	Access: read-write
OBJECT-TYPE
	Ipv6Address

ecpaConfigStreamUsePortSourceMAC		1.3.6.1.4.1.2544.1.12.8.1.2.1.28
This object when not enabled indicates that MAC Address specified by ecpaConfigStreamSourceMAC as the source MAC Address of the ECPA test stream. For EGX, if enabled indicates that the corresponding ECPA test stream will use the associated Source Port's MAC Address. For GE110 products and CC products, if enabled indicates that the corresponding ECPA test stream will use the associated Source Port's Diagnostic MAC Address.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

ecpaConfigStreamRateHi		1.3.6.1.4.1.2544.1.12.8.1.2.1.29
The object enables specification of the higher 32 bits of the traffic generation rate.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

ecpaTestStreamTable		1.3.6.1.4.1.2544.1.12.8.1.3
A list of entries containing results of a previous test.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EcpaTestStreamEntry

ecpaTestStreamEntry		1.3.6.1.4.1.2544.1.12.8.1.3.1
A conceptual row in the ecpaTestStreamTable. Entries in this table show results of the current ECPA test.
Status: current	Access: not-accessible
OBJECT-TYPE
	EcpaTestStreamEntry

ecpaTestStreamIndex		1.3.6.1.4.1.2544.1.12.8.1.3.1.1
An integer index value corresponding to the stream index for which the ECPA test was initiated.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..3

ecpaTestStreamSourcePort		1.3.6.1.4.1.2544.1.12.8.1.3.1.2
An integer index value corresponding to the ifIndex for which the ECPA test was initiated.
Status: current	Access: read-only
OBJECT-TYPE
	VariablePointer

ecpaTestStreamName		1.3.6.1.4.1.2544.1.12.8.1.3.1.3
Symbolic Stream Name that can be associated with an ECPA stream.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

ecpaTestStreamFrameSize		1.3.6.1.4.1.2544.1.12.8.1.3.1.4
This object enables specification of fixed length frame size in bytes for traffic generation. If not specified, default value of 64 bytes is used.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	64..9612

ecpaTestStreamRate		1.3.6.1.4.1.2544.1.12.8.1.3.1.5
The object enables specification of the traffic generation rate.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

ecpaTestStreamPayloadType		1.3.6.1.4.1.2544.1.12.8.1.3.1.6
This object enables specification of type of payload to generate `fixed' type indicates a generation pattern of 5A, A5, 5A, A5 bytes. `random' type indicates traffic generation with pseudo-random pattern.
Status: current	Access: read-write
OBJECT-TYPE
	EcpaPayloadType

ecpaTestStreamSignature		1.3.6.1.4.1.2544.1.12.8.1.3.1.7
Indicates an 8-byte signature specified by the user in hexadecimal or ASCII format. This signature is currently used by the FSP150Mx products for test frame recognition and will be appended directly after the ECPA Signature in the test frame and be 4-byte aligned. This will allow the F3 ECPA feature to interoperate with the existing FSP150Mx products. Hexadecimal signature must be prefixed with 0x/0X.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(10)

ecpaTestStreamDestinationMAC		1.3.6.1.4.1.2544.1.12.8.1.3.1.8
Allows specification of destination MAC in the generated traffic.
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

ecpaTestStreamSourceMAC		1.3.6.1.4.1.2544.1.12.8.1.3.1.9
Allows specification of source MAC in the generated traffic.
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

ecpaTestStreamOuterVlanEnabled		1.3.6.1.4.1.2544.1.12.8.1.3.1.10
Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly tagged ECPA stream is desired, this specification is mandatory.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

ecpaTestStreamOuterVlanId		1.3.6.1.4.1.2544.1.12.8.1.3.1.11
Outer VLAN Id associated with the ECPA stream. Valid only if ecpaTestStreamOuterVlanEnabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	VlanId

ecpaTestStreamOuterVlanPrio		1.3.6.1.4.1.2544.1.12.8.1.3.1.12
Outer VLAN Priority associated with the ECPA stream. Valid only if ecpaTestStreamOuterVlanEnabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	VlanPriority

ecpaTestStreamOuterVlanEtherType		1.3.6.1.4.1.2544.1.12.8.1.3.1.13
EtherType associated with the Outer VLAN Tag. Valid only if ecpaTestStreamOuterVlanEnabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ecpaTestStreamInnerVlanEnabled		1.3.6.1.4.1.2544.1.12.8.1.3.1.14
Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly tagged ECPA stream is desired, this specification is mandatory.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

ecpaTestStreamInnerVlanId		1.3.6.1.4.1.2544.1.12.8.1.3.1.15
Inner VLAN Id associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlanEnabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	VlanId

ecpaTestStreamInnerVlanPrio		1.3.6.1.4.1.2544.1.12.8.1.3.1.16
Inner VLAN Priority associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlanEnabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	VlanPriority

ecpaTestStreamInnerVlanEtherType		1.3.6.1.4.1.2544.1.12.8.1.3.1.17
EtherType associated with the Inner VLAN Tag. Valid only if ecpaTestStreamInnerVlanEnabled is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ecpaTestStreamIpVersion		1.3.6.1.4.1.2544.1.12.8.1.3.1.18
This object enables specification of IP data in the generated test traffic. Value of `ipv4' allows test data to be IP v4 compatible. Value of `ipv6' allows test data to be IP v6 compatible.
Status: current	Access: read-write
OBJECT-TYPE
	IpVersion

ecpaTestStreamIpV4Address		1.3.6.1.4.1.2544.1.12.8.1.3.1.19
This object enables specification of ipv4 IP Address for the test stream.This is used when ecpaTestStreamIpVersion is ipv4.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ecpaTestStreamIpV6Address		1.3.6.1.4.1.2544.1.12.8.1.3.1.20
This object enables specification of ipv6 IP Address for the test stream.This is used when ecpaTestStreamIpVersion is ipv6.
Status: current	Access: read-write
OBJECT-TYPE
	Ipv6Address

ecpaTestStreamPrioMapMode		1.3.6.1.4.1.2544.1.12.8.1.3.1.21
This object enables specification of Priority Mapping Mode for the test stream.
Status: current	Access: read-write
OBJECT-TYPE
	IpPriorityMapMode

ecpaTestStreamPrioVal		1.3.6.1.4.1.2544.1.12.8.1.3.1.22
This object enables specification of Priority Value for ecpaTestStreamPrioMapMode as TOS/DSCP.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..63

ecpaTestStreamMonStartTime		1.3.6.1.4.1.2544.1.12.8.1.3.1.23
The start time of the ECPA test for this stream.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

ecpaTestStreamMonEndTime		1.3.6.1.4.1.2544.1.12.8.1.3.1.24
The end time of the ECPA test for this stream.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

ecpaTestStreamMonElapsedTime		1.3.6.1.4.1.2544.1.12.8.1.3.1.25
The elapsed time of ECPA test for this stream in seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ecpaTestStreamMonTxFrames		1.3.6.1.4.1.2544.1.12.8.1.3.1.26
The total number of frames transmitted(generated) so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

ecpaTestStreamMonRxFrames		1.3.6.1.4.1.2544.1.12.8.1.3.1.27
The total number of frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

ecpaTestStreamMonRxPercentSuccess		1.3.6.1.4.1.2544.1.12.8.1.3.1.28
Received frames as a percentage of transmitted frames. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ecpaTestStreamMonRxOutOfSeqErrs		1.3.6.1.4.1.2544.1.12.8.1.3.1.29
The total number of out of sequence errors received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

ecpaTestStreamMonRxSeqGaps		1.3.6.1.4.1.2544.1.12.8.1.3.1.30
The total number of sequence gaps received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

ecpaTestStreamMonRxNonEcpaFrames		1.3.6.1.4.1.2544.1.12.8.1.3.1.31
The total number of non ECPA frames received during the execution.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

ecpaTestStreamMonRxMinDelay		1.3.6.1.4.1.2544.1.12.8.1.3.1.32
The minimum delay (in microseconds) across all frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ecpaTestStreamMonRxMaxDelay		1.3.6.1.4.1.2544.1.12.8.1.3.1.33
The maximum delay (in microseconds) across all frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ecpaTestStreamMonRxAvgDelay		1.3.6.1.4.1.2544.1.12.8.1.3.1.34
The average delay (in microseconds) across all frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ecpaTestStreamMonRx1stFrameSize		1.3.6.1.4.1.2544.1.12.8.1.3.1.35
Frame size of the Monitored First Frame.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	64..9612

ecpaTestStreamMonRx1stFrame1Octets		1.3.6.1.4.1.2544.1.12.8.1.3.1.36
The frame contents of the first received frame - first 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..2048)

ecpaTestStreamMonRx1stFrame2Octets		1.3.6.1.4.1.2544.1.12.8.1.3.1.37
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..2048)

ecpaTestStreamMonRx1stFrame3Octets		1.3.6.1.4.1.2544.1.12.8.1.3.1.38
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..2048)

ecpaTestStreamMonRx1stFrame4Octets		1.3.6.1.4.1.2544.1.12.8.1.3.1.39
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..2048)

ecpaTestStreamMonRx1stFrame5Octets		1.3.6.1.4.1.2544.1.12.8.1.3.1.40
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..2048)

ecpaTestStreamMonRx1stFrame6Octets		1.3.6.1.4.1.2544.1.12.8.1.3.1.41
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..2048)

ecpaTestStreamMonRx1stFrame7Octets		1.3.6.1.4.1.2544.1.12.8.1.3.1.42
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..2048)

ecpaTestStreamMonRx1stFrame8Octets		1.3.6.1.4.1.2544.1.12.8.1.3.1.43
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..2048)

ecpaTestStreamMonRx1stFrame9Octets		1.3.6.1.4.1.2544.1.12.8.1.3.1.44
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..2048)

ecpaTestStreamMonRx1stFrame10Octets		1.3.6.1.4.1.2544.1.12.8.1.3.1.45
The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..2048)

ecpaTestStreamMonRxBitRate		1.3.6.1.4.1.2544.1.12.8.1.3.1.46
The object provides the average bit rate on the ECPA test stream.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

ecpaTestStreamInnerVlan2Enabled		1.3.6.1.4.1.2544.1.12.8.1.3.1.47
This variable indicates the second(inner) VLAN specification, in the case of a 3-tagged ECPA stream. If a three tagged ECPA stream is desired, this indicates true.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

ecpaTestStreamInnerVlan2Id		1.3.6.1.4.1.2544.1.12.8.1.3.1.48
This variable provides the Inner (second) VLAN Id associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlan2Enabled is enabled.
Status: current	Access: read-only
OBJECT-TYPE
	VlanId

ecpaTestStreamInnerVlan2Prio		1.3.6.1.4.1.2544.1.12.8.1.3.1.49
This variable provides the Inner (second) VLAN Priority associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlan2Enabled is enabled.
Status: current	Access: read-only
OBJECT-TYPE
	VlanPriority

ecpaTestStreamInnerVlan2EtherType		1.3.6.1.4.1.2544.1.12.8.1.3.1.50
This variable provides the EtherType associated with the Inner (second) VLAN Tag. Valid only if ecpaTestStreamInnerVlan2Enabled is enabled.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

ecpaTestStreamDestIpV4Address		1.3.6.1.4.1.2544.1.12.8.1.3.1.51
This object provides the destination ipv4 IP Address for the test stream. This is valid when ecpaTestStreamIpVersion is ipv4.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

ecpaTestStreamDestIpV6Address		1.3.6.1.4.1.2544.1.12.8.1.3.1.52
This object provides the destination ipv6 IP Address for the test stream. This is valid when ecpaTestStreamIpVersion is ipv6.
Status: current	Access: read-only
OBJECT-TYPE
	Ipv6Address

ecpaTestStreamConfigChanged		1.3.6.1.4.1.2544.1.12.8.1.3.1.53
This object provides information on whether the associated ecpaConfigStream is changed.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

ecpaTestStreamRateHi		1.3.6.1.4.1.2544.1.12.8.1.3.1.54
The object enables specification of the higher 32 bits of the traffic generation rate.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

esaProbeTable		1.3.6.1.4.1.2544.1.12.8.1.4
A list of entries corresponding to ESA Probes.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsaProbeEntry

esaProbeEntry		1.3.6.1.4.1.2544.1.12.8.1.4.1
A row in the esaProbeTable. Entries can be created in this table by management application action. The slotIndex should be 255 if the product is cm5.1.
Status: current	Access: not-accessible
OBJECT-TYPE
	EsaProbeEntry

esaProbeIndex		1.3.6.1.4.1.2544.1.12.8.1.4.1.1
An integer index value used to uniquely identify this ESA Probe within a Card.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeName		1.3.6.1.4.1.2544.1.12.8.1.4.1.2
A unique identifier used by the Manager to distinguish the ESA Probe.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..15)

esaProbeSourcePort		1.3.6.1.4.1.2544.1.12.8.1.4.1.3
This object points to the Port to which the ESA Probe is attached, i.e.on which the service to be monitored resides.
Status: current	Access: read-create
OBJECT-TYPE
	VariablePointer

esaProbeAssocSchedGroup		1.3.6.1.4.1.2544.1.12.8.1.4.1.4
This object points to the probe's associated Scheduled Group. Initially, when the probe is not associated with a Group, this object's value is set to {0.0}.
Status: current	Access: read-only
OBJECT-TYPE
	VariablePointer

esaProbeDirection		1.3.6.1.4.1.2544.1.12.8.1.4.1.5
This object allows to specify the direction of Probe traffic generation.
Status: current	Access: read-create
OBJECT-TYPE
	EsaProbeDirection

esaProbeProtocol		1.3.6.1.4.1.2544.1.12.8.1.4.1.6
Protocol to be used in ESA Probe messages. 'icmpTimestamp', 'icmpEcho', 'udpEcho' protocols support layer-3 ethernet service assurance. If the remote reflector is an ADVA equipment based on CM family of products, one-way loss measurement, one-way delay measurement, round-trip delay measurement and one-way jitter measurements are computed. Else, only round-trip delay measurements are applicable. 'y1731' protocol can be used for layer-2 ethernet service assurance. One-way loss measurement, one-way and round-trip delay measurement, and one-way jitter measurements are available for this protocol. 'y1731-slm-slr' protocol can be used for layer-2 ethernet service assurance using Synthetic Loss Measurement messages. One-way loss measurement, one-way and round-trip delay measurement, and one-way jitter measurements are available for this protocol.
Status: current	Access: read-create
OBJECT-TYPE
	EsaProbeProtocol

esaProbeSrcIpAddress		1.3.6.1.4.1.2544.1.12.8.1.4.1.7
Variable that allows specification of the Probe's source IP Address. This IP Address is used in the IP header of the ESA Probe generated packets, as source address. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

esaProbeSrcSubnetMask		1.3.6.1.4.1.2544.1.12.8.1.4.1.8
Variable that allows specification of the Probe's source IP Subnet Mask. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

esaProbeDestIpAddress		1.3.6.1.4.1.2544.1.12.8.1.4.1.9
Variable that allows specification of the Reflector's destination IP Address. This IP Address is used in the IP header of the ESA Probe generated packets, as destination address. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

esaProbeSrcMep		1.3.6.1.4.1.2544.1.12.8.1.4.1.10
This attribute is applicable only for Y.1731 probes. It identifies the source MEP that initiates the Y.1731 LMMs and DMMs.
Status: current	Access: read-create
OBJECT-TYPE
	VariablePointer

esaProbeDestMepType		1.3.6.1.4.1.2544.1.12.8.1.4.1.11
This attribute is applicable only for Y.1731 probes. This indicates if the destination MEP is specified using the MEP ID object esaProbeDestMepId.
Status: current	Access: read-create
OBJECT-TYPE
	MepDestinationType

esaProbeDestMepMacAddr		1.3.6.1.4.1.2544.1.12.8.1.4.1.12
This attribute is applicable only for Y.1731 probes. It identifies the destination MEP that responds to the LMMs and DMMs. This MAC address will be the destination MAC address for LMM and DMM frames if esaProbeY1731DestMepType is 'macaddress'. If CC protocol is not enabled between source and destination MEP then this is the only choice to identify the remote MEP.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

esaProbeDestMepId		1.3.6.1.4.1.2544.1.12.8.1.4.1.13
This attribute is applicable only for Y.1731 probes. It identifies the destination MEP that responds to the LMMs and DMMs. The MAC address of this RMEP ID from RMEP database will be the destination MAC address for LMM and DMM. This value is used only if the esaProbeY1731DestMepType is 'mepid'. CC protocol must be enabled between source and destination MEP if the RMEP ID is used to identify the Remote MEP.
Status: current	Access: read-create
OBJECT-TYPE
	Dot1agCfmMepIdOrZero

esaProbeVlanTagEnabled		1.3.6.1.4.1.2544.1.12.8.1.4.1.14
Ability to specify whether or not to use VLAN tagged or untagged ESA traffic generation on the Probe. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

esaProbeVlanTagEtherType		1.3.6.1.4.1.2544.1.12.8.1.4.1.15
This variable allows the user to specify the monitored service's VLAN tag Ether Type. Valid if 'esaProbeVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

esaProbeVlanId		1.3.6.1.4.1.2544.1.12.8.1.4.1.16
This variable allows the user to specify the monitored service's VLAN tag. Valid if 'esaProbeVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	VlanId

esaProbeVlanPrio		1.3.6.1.4.1.2544.1.12.8.1.4.1.17
This variable allows the user to specify the monitored service's VLAN priority. Valid if 'esaProbeVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	VlanPriority

esaProbeInnerVlanTagEnabled		1.3.6.1.4.1.2544.1.12.8.1.4.1.18
Ability to specify whether or not to use Inner VLAN tag. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

esaProbeInnerVlanTagEtherType		1.3.6.1.4.1.2544.1.12.8.1.4.1.19
This variable allows the user to specify the monitored service's Inner VLAN tag Ether Type. Valid if 'esaProbeInnerVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

esaProbeInnerVlanId		1.3.6.1.4.1.2544.1.12.8.1.4.1.20
This variable allows the user to specify the monitored service's Inner VLAN tag. Valid if 'esaProbeInnerVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	VlanId

esaProbeInnerVlanPrio		1.3.6.1.4.1.2544.1.12.8.1.4.1.21
This variable allows the user to specify the monitored service's Inner VLAN priority. Valid if 'esaProbeInnerVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	VlanPriority

esaProbeIpPrioMapMode		1.3.6.1.4.1.2544.1.12.8.1.4.1.22
This object enables specification of Priority Mapping Mode for the ESA Probe. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	IpPriorityMapMode

esaProbeIpPriority		1.3.6.1.4.1.2544.1.12.8.1.4.1.23
This object enables specification of Priority Value for esaProbePrioMapMode as priomap-tos,priomap-dscp. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..63

esaProbePktsPerSample		1.3.6.1.4.1.2544.1.12.8.1.4.1.24
This object enables specification of number of packets within a sample run for ESA traffic generation. A non-zero value must be specified. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbePktSize		1.3.6.1.4.1.2544.1.12.8.1.4.1.25
This object enables specification of fixed length frame size in bytes for ESA traffic generation. If not specified, default value of 104 bytes is used. NOTE: This attribute is not available to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0 | 64..2000

esaProbeInterPktGap		1.3.6.1.4.1.2544.1.12.8.1.4.1.26
This object enables specification of interval in milliseconds between packet generation. A non-zero value must be specified. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbePktDeadInterval		1.3.6.1.4.1.2544.1.12.8.1.4.1.27
This object enables specification of the dead interval in seconds after 'esaProbePktsPerSample' have been generated within the sample. This allows for settling time of the ESA traffic. A non-zero value must be specified. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbeResponseTimeout		1.3.6.1.4.1.2544.1.12.8.1.4.1.28
This object allows specification of the timeout value to determine lost packets. Time specified in seconds. NOTE: This attribute is not applicable to Y.1731 probes. This object is applicable to Layer 3 and SLM/SLR Probes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbeY1731DmmPktSize		1.3.6.1.4.1.2544.1.12.8.1.4.1.29
This object is only applicable to Y.1731 probes. This object enables specification of the TLV size for Delay Measurement Frames (DMMs). Value of 0 is a read-only value when the Probe protocol is not y1731. GE206 Release 4.4.x supports 2000 bytes
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0 | 64..9600

esaProbeY1731LmmInterval		1.3.6.1.4.1.2544.1.12.8.1.4.1.30
LMM frame transmission period. For Loss Measurement Frames, only interval-1sec is supported. This attribute is only applicable to Y.1731 probes.
Status: current	Access: read-create
OBJECT-TYPE
	EsaProbePktIntervalType

esaProbeY1731DmmInterval		1.3.6.1.4.1.2544.1.12.8.1.4.1.31
DMM frame transmission period. This attribute is only applicable to Y.1731 probes.
Status: current	Access: read-create
OBJECT-TYPE
	EsaProbePktIntervalType

esaProbeHistoryBins		1.3.6.1.4.1.2544.1.12.8.1.4.1.32
This object allows specification of number of history bins. This is the total history data that will be maintained for an ESA Probe run, at any instance.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..32

esaProbeHistoryInterval		1.3.6.1.4.1.2544.1.12.8.1.4.1.33
This object allows specification of the history interval period.
Status: current	Access: read-write
OBJECT-TYPE
	EsaProbeHistoryIntervalType

esaProbeDistHistoryBins		1.3.6.1.4.1.2544.1.12.8.1.4.1.34
This object allows specification of number of distribution history bins. This is the total history distribution data that will be maintained for an ESA Probe run, at any instance.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..32

esaProbeDistHistoryInterval		1.3.6.1.4.1.2544.1.12.8.1.4.1.35
This object allows specification of the history distribution interval period.
Status: current	Access: read-write
OBJECT-TYPE
	EsaProbeHistoryIntervalType

esaProbeCreationTime		1.3.6.1.4.1.2544.1.12.8.1.4.1.36
This object provides the creation time of the ESA Probe.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

esaProbeStorageType		1.3.6.1.4.1.2544.1.12.8.1.4.1.37
The type of storage configured for this entry.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

esaProbeRowStatus		1.3.6.1.4.1.2544.1.12.8.1.4.1.38
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaProbeRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaProbeRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaProbeRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

esaProbeMultiCOSEnabled		1.3.6.1.4.1.2544.1.12.8.1.4.1.39
This object is introduced for FSP150CC Release 4.3. This object is only applicable for Y.1731 and SLM-SLR Probe Protocol Types. This object can be used to specify the multiple class of services (COS) for each ESA Probe.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

esaProbeSLAMonitorType		1.3.6.1.4.1.2544.1.12.8.1.4.1.40
This object indicates whether the Probe is a point-to-point type or a point-to-multipoint type. Only SLM-SLR probes can be point-to-multipoint.
Status: current	Access: read-create
OBJECT-TYPE
	EsaProbeSLAMonitorType

esaProbeCOSType		1.3.6.1.4.1.2544.1.12.8.1.4.1.41
This object can be used to specify the first Class of Service associated with the Y.1731/SLM-SLR ESA Probe. In the case of a multiCOS Probe, this object has no semantics when multiple COS levels exist. This object is only valid for Y.1731/SLM-SLR ESA Probes.
Status: current	Access: read-create
OBJECT-TYPE
	ClassOfServiceType

esaProbeSLMMulticastMACEnabled		1.3.6.1.4.1.2544.1.12.8.1.4.1.42
This object can be used to specify whether the SLM/SLR protocol Probe will use multicast MAC address in SLM (Synthetic Loss Measurement) messages. This object is only valid for SLM-SLR ESA Probes.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

esaProbeSOAMInterval		1.3.6.1.4.1.2544.1.12.8.1.4.1.43
This object can be used to specify the packet interval type for Y.1731 LM/DM and SLM/SLR based ESA Probes, for the first Class of Service. In the case of a multiCOS Probe, this object has no semantics when multiple COS levels exist. This attribute is applicable for Y.1731 LM/DM and SLM/SLR based probes.
Status: current	Access: read-create
OBJECT-TYPE
	EsaProbePktIntervalType

esaProbeSOAMPktSize		1.3.6.1.4.1.2544.1.12.8.1.4.1.44
This object can be used to specify the packet size for SLM-SLR based ESA Probes, for the first Class of Service. In the case of multiCOS Probe, this object has no semantics when multiple COS levels exist. In such cases this will return a value of 0.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0 | 64..9612

esaProbeInner2VlanTagEnabled		1.3.6.1.4.1.2544.1.12.8.1.4.1.45
Ability to specify whether or not to use Inner2 VLAN tag. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

esaProbeInner2VlanTagEtherType		1.3.6.1.4.1.2544.1.12.8.1.4.1.46
This variable allows the user to specify the monitored service's Inner2 VLAN tag Ether Type. Valid if 'esaProbeInner2VlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

esaProbeInner2VlanId		1.3.6.1.4.1.2544.1.12.8.1.4.1.47
This variable allows the user to specify the monitored service's Inner2 VLAN tag. Valid if 'esaProbeInner2VlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	VlanId

esaProbeInner2VlanPrio		1.3.6.1.4.1.2544.1.12.8.1.4.1.48
This variable allows the user to specify the monitored service's Inner2 VLAN priority. Valid if 'esaProbeInner2VlanTagEnabled' is specified as TRUE. NOTE: This attribute is not applicable to Y.1731 probes.
Status: current	Access: read-write
OBJECT-TYPE
	VlanPriority

esaProbeAdminState		1.3.6.1.4.1.2544.1.12.8.1.4.1.49
This object represents the Administrative State of the ESA Probe. This is not externally managed.
Status: current	Access: read-only
OBJECT-TYPE
	AdminState

esaProbeOperationalState		1.3.6.1.4.1.2544.1.12.8.1.4.1.50
This object represents the Operational State of the ESA Probe.
Status: current	Access: read-only
OBJECT-TYPE
	OperationalState

esaProbeSecondaryState		1.3.6.1.4.1.2544.1.12.8.1.4.1.51
This object represents the Secondary State of the ESA Probe.
Status: current	Access: read-only
OBJECT-TYPE
	SecondaryState

esaProbeMacAddress		1.3.6.1.4.1.2544.1.12.8.1.4.1.52
This attribute is applicable only for Y.1731 probes. It identifies the destination MacAddress which esa using
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

esaProbeAlias		1.3.6.1.4.1.2544.1.12.8.1.4.1.53
This object allows SNMP management entities to provide an alias for an ESA Probe.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..128)

esaProbeScheduleGroupTable		1.3.6.1.4.1.2544.1.12.8.1.5
A list of entries that allow groups of ESA Probes to be scheduled.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsaProbeScheduleGroupEntry

esaProbeScheduleGroupEntry		1.3.6.1.4.1.2544.1.12.8.1.5.1
A row in esaProbeScheduleGroupTable. Entries are created in this table by management application action.
Status: current	Access: not-accessible
OBJECT-TYPE
	EsaProbeScheduleGroupEntry

esaProbeScheduleGroupIndex		1.3.6.1.4.1.2544.1.12.8.1.5.1.1
A unique index to distinguish the ESA Probe Schedule Group.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

esaProbeScheduleGroupDescr		1.3.6.1.4.1.2544.1.12.8.1.5.1.2
Description of the probe schedule group.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..256)

esaProbeScheduleGroupProbeList		1.3.6.1.4.1.2544.1.12.8.1.5.1.3
A comma separated list of esaProbeName's, that will have the same schedule.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..512)

esaProbeScheduleGroupType		1.3.6.1.4.1.2544.1.12.8.1.5.1.4
This object allows to specify whether the ESA probe group schedule is 'one-shot' or 'periodic'. A 'one-shot' schedule executes only once and then stops. A 'periodic' schedule reoccurs every 'esaProbeScheduleGroupInterval' seconds and continues until explicitly stopped.
Status: current	Access: read-create
OBJECT-TYPE
	ScheduleType

esaProbeScheduleGroupStartTime		1.3.6.1.4.1.2544.1.12.8.1.5.1.5
This object allows specification of the start time of the ESA Probe Group. Value of time less than current system time will equate to current time. When the system time reaches this configured time, the ESA Probe Group will be activated.
Status: current	Access: read-create
OBJECT-TYPE
	DateAndTime

esaProbeScheduleGroupDuration		1.3.6.1.4.1.2544.1.12.8.1.5.1.6
This object allows specification of the duration in 'seconds' for ESA Probe Group run. Note that a value of 4294967295 means Duration as FOREVER. FOREVER value is only applicable to schedule type oneshot. The value 4294967295 cannot be used if schedule type is periodic.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

esaProbeScheduleGroupInterval		1.3.6.1.4.1.2544.1.12.8.1.5.1.7
This object allows specification of the interval in 'seconds' between successive runs for ESA Probe Group. This variable is only valid if the 'esaProbeScheduleGroupType' is 'periodic'.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

esaProbeScheduleGroupAction		1.3.6.1.4.1.2544.1.12.8.1.5.1.8
This object allows to suspend/resume the ESA scheduled group.
Status: current	Access: read-write
OBJECT-TYPE
	EsaAction

esaProbeScheduleGroupStatus		1.3.6.1.4.1.2544.1.12.8.1.5.1.9
This object indicates the current status of the ESA Probe Group.
Status: current	Access: read-only
OBJECT-TYPE
	SchedActivityStatus

esaProbeScheduleGroupStorageType		1.3.6.1.4.1.2544.1.12.8.1.5.1.10
The type of storage configured for this entry.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

esaProbeScheduleGroupRowStatus		1.3.6.1.4.1.2544.1.12.8.1.5.1.11
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaProbeScheduleGroupRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaProbeRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaProbeScheduleGroupRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

esaProbeScheduleGroupActionProbeList		1.3.6.1.4.1.2544.1.12.8.1.5.1.12
A comma separated list of esaProbeName's, if set esaProbeScheduleGroupAction as add or remove, they will be add or remove from esaProbeScheduleGroupProbeList.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..512)

esaReflectorTable		1.3.6.1.4.1.2544.1.12.8.1.6
A list of entries corresponding to ESA Reflectors. NOTE: There is no need to create reflectors for Y.1731 probes as the MEPs will respond by default.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsaReflectorEntry

esaReflectorEntry		1.3.6.1.4.1.2544.1.12.8.1.6.1
A row in the esaReflectorTable. Entries can be created in this table by management application action.
Status: current	Access: not-accessible
OBJECT-TYPE
	EsaReflectorEntry

esaReflectorIndex		1.3.6.1.4.1.2544.1.12.8.1.6.1.1
A unique index to distinguish the ESA Reflector.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

esaReflectorName		1.3.6.1.4.1.2544.1.12.8.1.6.1.2
A unique identifier to distinguish the ESA Reflector.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..15)

esaReflectorIpAddress		1.3.6.1.4.1.2544.1.12.8.1.6.1.3
This object allows specification of the Reflector's IP Address. Reflector listens for packets destined at this IP Address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

esaReflectorSubnetMask		1.3.6.1.4.1.2544.1.12.8.1.6.1.4
This object allows specification of the Reflector's IP Subnet mask.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

esaReflectorSourcePort		1.3.6.1.4.1.2544.1.12.8.1.6.1.5
This object points to the Port to which the ESA Reflector is attached, i.e.on which the service to be monitored resides.
Status: current	Access: read-create
OBJECT-TYPE
	VariablePointer

esaReflectorIpPrioMapMode		1.3.6.1.4.1.2544.1.12.8.1.6.1.6
This object enables specification of Priority Mapping Mode for the ESA Reflector.
Status: current	Access: read-write
OBJECT-TYPE
	IpPriorityMapMode

esaReflectorIpPriority		1.3.6.1.4.1.2544.1.12.8.1.6.1.7
This object enables specification of Priority Value for esaReflectorPrioMapMode as priomap-tos,priomap-dscp.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..63

esaReflectorAction		1.3.6.1.4.1.2544.1.12.8.1.6.1.8
This object allows to suspend/resume the ESA reflector.
Status: current	Access: read-write
OBJECT-TYPE
	EsaAction

esaReflectorSuspended		1.3.6.1.4.1.2544.1.12.8.1.6.1.9
This object indicates whether the ESA Reflector is active or suspended.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

esaReflectorCreationTime		1.3.6.1.4.1.2544.1.12.8.1.6.1.10
This object provides the creation time of the ESA Reflector.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

esaReflectorStorageType		1.3.6.1.4.1.2544.1.12.8.1.6.1.11
The type of storage configured for this entry.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

esaReflectorRowStatus		1.3.6.1.4.1.2544.1.12.8.1.6.1.12
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaReflectorRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaReflectorRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaReflectorRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

esaReflectorDirection		1.3.6.1.4.1.2544.1.12.8.1.6.1.13
This object provides the direction of the ESA Reflector.
Status: current	Access: read-create
OBJECT-TYPE
	EsaReflectorDirection

esaReflectorAdminState		1.3.6.1.4.1.2544.1.12.8.1.6.1.14
This object represents the Administrative State of the ESA Reflector. This is not externally managed.
Status: current	Access: read-only
OBJECT-TYPE
	AdminState

esaReflectorOperationalState		1.3.6.1.4.1.2544.1.12.8.1.6.1.15
This object represents the Operational State of the ESA Reflector.
Status: current	Access: read-only
OBJECT-TYPE
	OperationalState

esaReflectorSecondaryState		1.3.6.1.4.1.2544.1.12.8.1.6.1.16
This object represents the Secondary State of the ESA Reflector.
Status: current	Access: read-only
OBJECT-TYPE
	SecondaryState

esaReflectorMacAddress		1.3.6.1.4.1.2544.1.12.8.1.6.1.17
This attribute is applicable only for Y.1731 probes. It identifies the destination MacAddress which esa using
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

esaReflectorAlias		1.3.6.1.4.1.2544.1.12.8.1.6.1.18
This object allows SNMP management entities to provide an alias for an ESA Reflector.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..128)

esaProbeStatsTable		1.3.6.1.4.1.2544.1.12.8.1.7
A collection of ESA Probe related statistics kept for a particular ESA Probe entity. These reflect the current data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsaProbeStatsEntry

esaProbeStatsEntry		1.3.6.1.4.1.2544.1.12.8.1.7.1
A conceptual row in the esaProbeStatsTable. An entry exists in this table for each ESA Probe.
Status: current	Access: not-accessible
OBJECT-TYPE
	EsaProbeStatsEntry

esaProbeStatsDestinationIndex		1.3.6.1.4.1.2544.1.12.8.1.7.1.1
An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since only point-to-point SLA is supported.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeStatsCOSIndex		1.3.6.1.4.1.2544.1.12.8.1.7.1.2
An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly specified in the Probe parameters.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeStatsIndex		1.3.6.1.4.1.2544.1.12.8.1.7.1.3
An arbitrary integer index value used to uniquely identify this ESA Probe statistics entry. Index 1 corresponds to current and index 2 to rollover.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2

esaProbeStatsIntervalType		1.3.6.1.4.1.2544.1.12.8.1.7.1.4
Indicates the type of collection, i.e. whether it is current, or rollover.
Status: current	Access: read-only
OBJECT-TYPE
	EsaProbePmIntervalType

esaProbeStatsCOS		1.3.6.1.4.1.2544.1.12.8.1.7.1.5
The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported.
Status: current	Access: read-only
OBJECT-TYPE
	ClassOfServiceType

esaProbeStatsValid		1.3.6.1.4.1.2544.1.12.8.1.7.1.6
Indicates the validity of the bin.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

esaProbeStatsAction		1.3.6.1.4.1.2544.1.12.8.1.7.1.7
Allows the Manager to clear the bin.
Status: current	Access: read-write
OBJECT-TYPE
	CmPmBinAction

esaProbeStatsP2RPkts		1.3.6.1.4.1.2544.1.12.8.1.7.1.8
The total number of Transmitted Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) received and this will always be the same as the esaProbeStatsR2PPkts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsP2RErredPkts		1.3.6.1.4.1.2544.1.12.8.1.7.1.9
The total number of Packets in the current interval, for which there was a problem in transmission. This error is counted when there is a failure in packet transmission due to resource limitations (buffers). This can happen if the Probe Configuration was changed to send in a large number of packets in a time interval. NOTE: This is not applicable for Y.1731 probes.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsP2RSyncErrs		1.3.6.1.4.1.2544.1.12.8.1.7.1.10
The number of (time) Synchronization Errors from probe to reflector in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsP2RLostPkts		1.3.6.1.4.1.2544.1.12.8.1.7.1.11
The number of Lost Pkts from probe to reflector in the current interval. For Y.1731 probes, these are the actual data frames lost.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsR2PPkts		1.3.6.1.4.1.2544.1.12.8.1.7.1.12
The total number of Received Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) received and this will always be the same as the esaProbeStatsP2RPkts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsR2PErredPkts		1.3.6.1.4.1.2544.1.12.8.1.7.1.13
The total number of Received Packets in the current interval, which had errors such as length of received packet is less than the protocol header length, packet was received after it was marked as lost (i.e.beyond timeout). NOTE: This is not applicable for Y.1731 probes.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsR2PSyncErrs		1.3.6.1.4.1.2544.1.12.8.1.7.1.14
The number of (time) Synchronization Errors from reflector to probe in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsR2PLostPkts		1.3.6.1.4.1.2544.1.12.8.1.7.1.15
The number of Lost Pkts from reflector to probe in the current interval. For Y.1731 probes, these are the actual data frames lost.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsLostPkts		1.3.6.1.4.1.2544.1.12.8.1.7.1.16
The total number of Lost Packets in the current interval. Packets which are not received from the reflector end beyond the configured timeout value are termed as lost. NOTE: This is not applicable for Y.1731 probes.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSeqGaps		1.3.6.1.4.1.2544.1.12.8.1.7.1.17
The total number of sequence gaps across all packets received in the current interval. If (Received Seq Number) is greater than or equal to (Last Received Seq Number + 2)) it is termed as a sequence gap. NOTE: This is not applicable for Y.1731 probes.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsOutOfSeqErrs		1.3.6.1.4.1.2544.1.12.8.1.7.1.18
The total number of out of sequence errors across all packets received in the current interval. If (Received Seq Number) is less than or equal to (Last Received Seq Number), it is termed as out of sequence error. NOTE: This is not applicable for Y.1731 probes.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsMinRoundTripDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.19
The minimum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsMaxRoundTripDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.20
The maximum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsAvgRoundTripDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.21
The average round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsSumRoundTripDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.22
The total sum of round trip delay(in microseconds) in the current interval. The reflector's processing time is excluded from the value.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumOfSqRoundTripDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.23
The sum of square of round trip delays in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsMinOnewayP2RDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.24
The minimum one-way source to destination delay(in microseconds) across all packets received in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsMaxOnewayP2RDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.25
The maximum one-way source to destination delay(in microseconds) across all packets received in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsAvgOnewayP2RDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.26
The average one-way source to destination delay(in microseconds) across all packets received in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsSumOnewayP2RDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.27
The total sum of one-way delay from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumOfSqOnewayP2RDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.28
The sum of square of one-way delay from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsMinOnewayR2PDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.29
The minimum one-way destination to source delay(in microseconds) across all packets received in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsMaxOnewayR2PDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.30
The maximum one-way destination to source delay(in microseconds) across all packets received in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsAvgOnewayR2PDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.31
The average one-way destination to source delay(in microseconds) across all packets received in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsSumOnewayR2PDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.32
The total sum of one-way delay from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumOfSqOnewayR2PDelay		1.3.6.1.4.1.2544.1.12.8.1.7.1.33
The sum of square of one-way delay from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsMinPosP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.34
The minimum positive one-way jitter from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsMaxPosP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.35
The maximum positive one-way jitter from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsNumPosP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.36
The total number of positive one-way jitters from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumPosP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.37
The total sum of positive one-way jitters from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumOfSqPosP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.38
The sum of square of positive one-way jitters from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsMinNegP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.39
The minimum negative one-way jitter from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsMaxNegP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.40
The maximum negative one-way jitter from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsNumNegP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.41
The total number of negative one-way jitters from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumNegP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.42
The total sum of negative one-way jitters from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumOfSqNegP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.43
The sum of square of negative one-way jitters from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsMinPosR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.44
The minimum positive one-way jitter from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsMaxPosR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.45
The maximum positive one-way jitter from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsNumPosR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.46
The total number of positive one-way jitters from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumPosR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.47
The total sum of positive one-way jitters from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumOfSqPosR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.48
The sum of square of positive one-way jitters from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsMinNegR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.49
The minimum negative one-way jitter from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsMaxNegR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.50
The maximum negative one-way jitter from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsNumNegR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.51
The total number of negative one-way jitters from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumNegR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.52
The total sum of negative one-way jitters from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumOfSqNegR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.53
The sum of square of negative one-way jitters from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsY1731P2RNegLossOccurrences		1.3.6.1.4.1.2544.1.12.8.1.7.1.54
This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from Source MEP (Probe) to Destination MEP (Reflector). If these counts are non-zero then there could be some kind of provisioning mismatch between the Probe MEP and Reflector MEP. Here are some scenarios this can happen: - Probe MEP is configured to count in-profile frames only and the Reflector MEP is configured to count all frames with a mismatch in value for the attribute cfmMepLmCountInProfileFrames. - Probe MEP is configured to count data frames for specific VLAN priority and the Reflector MEP is configured to count data frames for all the priorities with a mismatch in values for the attributes cfmMepLmTxCountAllPrios or cfmMepLmRxCountAllPrios. NOTE: This could possibly happen due to reasons not related to configuration such as frame reordering in the network.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsY1731R2PNegLossOccurrences		1.3.6.1.4.1.2544.1.12.8.1.7.1.55
This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from to Destination MEP (Reflector) to Source MEP (Probe). If these counts are non-zero then there could be some kind of provisioning mismatch between the Probe MEP and Reflector MEP. Here are some scenarios this can happen: - Probe MEP is configured to count in-profile frames only and the Reflector MEP is configured to count all frames with a mismatch in value for the attribute cfmMepLmCountInProfileFrames. - Probe MEP is configured to count data frames for specific VLAN priority and the Reflector MEP is configured to count data frames for all the priorities with a mismatch in values for the attributes cfmMepLmTxCountAllPrios or cfmMepLmRxCountAllPrios. NOTE: This could possibly happen due to reasons not related to configuration such as frame reordering in the network.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsY1731RxLmSamples		1.3.6.1.4.1.2544.1.12.8.1.7.1.56
This attribute is only applicable to Y.1731 probes. This flag indicates that at least one loss measurement sample was received for this bin period (LMRs received). This is used by the user to differentiate between valid zero frame loss and not receiving any LMRs.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

esaProbeStatsY1731RxDmSamples		1.3.6.1.4.1.2544.1.12.8.1.7.1.57
This attribute is only applicable to Y.1731 probes. This flag indicates that at least one delay measurement sample was received for this bin period (DMRs received).
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

esaProbeStatsY1731P2RFrames		1.3.6.1.4.1.2544.1.12.8.1.7.1.58
This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Source MEP (Probe) that are transmitted towards the Destination MEP (Reflector). Based on the configuration the MEP counts the data frames with: - MEP's LM TX priority or all the priorities - All the VLAN IDs belonging the MEP's MA VID list.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsY1731R2PFrames		1.3.6.1.4.1.2544.1.12.8.1.7.1.59
This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Destination MEP (Reflector) that are transmitted towards the Source MEP (Probe). Based on the configuration the MEP counts the data frames with: - MEP's LM RX priority or all the priorities - All the VLAN IDs belonging the MEP's MA VID list.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsAvgAbsP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.60
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute P2R Jitter value. .
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsAvgAbsR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.61
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute R2P Jitter value. .
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsMinAbsP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.62
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute P2R Jitter value. .
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsMinAbsR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.63
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute R2P Jitter value. .
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsMaxAbsP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.64
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute P2R Jitter value. .
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsMaxAbsR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.65
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute R2P Jitter value. .
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeStatsNumAbsP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.66
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute P2R Jitters.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsNumAbsR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.67
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute R2P Jitters.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumAbsP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.68
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute P2R Jitter values.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumAbsR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.69
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute R2P Jitter values.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumOfSqAbsP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.70
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute P2R Jitter values.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsSumOfSqAbsR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.7.1.71
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute R2P Jitter values.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryTable		1.3.6.1.4.1.2544.1.12.8.1.8
A collection of ESA Probe related history kept for a particular ESA Probe entity. These reflect the current data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsaProbeHistoryEntry

esaProbeHistoryEntry		1.3.6.1.4.1.2544.1.12.8.1.8.1
A conceptual row in the esaProbeHistoryTable. An entry exists in this table for each ESA Probe.
Status: current	Access: not-accessible
OBJECT-TYPE
	EsaProbeHistoryEntry

esaProbeHistoryDestinationIndex		1.3.6.1.4.1.2544.1.12.8.1.8.1.1
An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since only point-to-point SLA is supported.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeHistoryCOSIndex		1.3.6.1.4.1.2544.1.12.8.1.8.1.2
An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly specified in the Probe parameters.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeHistoryIndex		1.3.6.1.4.1.2544.1.12.8.1.8.1.3
An arbitrary integer index value used to uniquely identify this ESA Probe statistics history entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeHistoryTime		1.3.6.1.4.1.2544.1.12.8.1.8.1.4
Indicates the time of history bin creation.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

esaProbeHistoryValid		1.3.6.1.4.1.2544.1.12.8.1.8.1.5
Indicates the validity of the bin.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

esaProbeHistoryAction		1.3.6.1.4.1.2544.1.12.8.1.8.1.6
Allows the Manager to clear the bin.
Status: current	Access: read-write
OBJECT-TYPE
	CmPmBinAction

esaProbeHistoryCOS		1.3.6.1.4.1.2544.1.12.8.1.8.1.7
The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported.
Status: current	Access: read-only
OBJECT-TYPE
	ClassOfServiceType

esaProbeHistoryP2RPkts		1.3.6.1.4.1.2544.1.12.8.1.8.1.8
The total number of Transmitted Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) received and this will always be the same as the esaProbeHistoryR2PPkts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryP2RErredPkts		1.3.6.1.4.1.2544.1.12.8.1.8.1.9
The total number of Packets in the current interval, for which there was a problem in transmission. This error is counted when there is a failure in packet transmission due to resource limitations (buffers). This can happen if the Probe Configuration was changed to send in a large number of packets in a time interval. NOTE: This is not applicable for Y.1731 probes.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryP2RSyncErrs		1.3.6.1.4.1.2544.1.12.8.1.8.1.10
The number of (time) Synchronization Errors from probe to reflector in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryP2RLostPkts		1.3.6.1.4.1.2544.1.12.8.1.8.1.11
The number of Lost Pkts from probe to reflector in the current interval. For Y.1731 probes, these are the actual data frames lost.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryR2PPkts		1.3.6.1.4.1.2544.1.12.8.1.8.1.12
The total number of Received Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) received and this will always be the same as the esaProbeHistoryP2RPkts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryR2PErredPkts		1.3.6.1.4.1.2544.1.12.8.1.8.1.13
The total number of Received Packets in the current interval, which had errors such as length of received packet is less than the protocol header length, packet was received after it was marked as lost (i.e.beyond timeout). NOTE: This is not applicable for Y.1731 probes.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryR2PSyncErrs		1.3.6.1.4.1.2544.1.12.8.1.8.1.14
The number of (time) Synchronization Errors from reflector to probe in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryR2PLostPkts		1.3.6.1.4.1.2544.1.12.8.1.8.1.15
The number of Lost Pkts from reflector to probe in the current interval. For Y.1731 probes, these are the actual data frames lost.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryLostPkts		1.3.6.1.4.1.2544.1.12.8.1.8.1.16
The total number of Lost Packets in the current interval. Packets which are not received from the reflector end beyond the configured timeout value are termed as lost. NOTE: This is not applicable for Y.1731 probes.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySeqGaps		1.3.6.1.4.1.2544.1.12.8.1.8.1.17
The total number of sequence gaps across all packets received in the current interval. If (Received Seq Number) is greater than or equal to (Last Received Seq Number + 2)) it is termed as a sequence gap. NOTE: This is not applicable for Y.1731 probes.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryOutOfSeqErrs		1.3.6.1.4.1.2544.1.12.8.1.8.1.18
The total number of out of sequence errors across all packets received in the current interval. If (Received Seq Number) is less than or equal to (Last Received Seq Number), it is termed as out of sequence error. NOTE: This is not applicable for Y.1731 probes.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryMinRoundTripDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.19
The minimum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryMaxRoundTripDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.20
The maximum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryAvgRoundTripDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.21
The average round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistorySumRoundTripDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.22
The total sum of round trip delay(in microseconds) in the current interval. The reflector's processing time is excluded from the value.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumOfSqRoundTripDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.23
The sum of square of round trip delays in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryMinOnewayP2RDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.24
The minimum one-way source to destination delay(in microseconds) across all packets received in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryMaxOnewayP2RDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.25
The maximum one-way source to destination delay(in microseconds) across all packets received in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryAvgOnewayP2RDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.26
The average one-way source to destination delay(in microseconds) across all packets received in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistorySumOnewayP2RDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.27
The total sum of one-way delay from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumOfSqOnewayP2RDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.28
The sum of square of one-way delay from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryMinOnewayR2PDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.29
The minimum one-way destination to source delay(in microseconds) across all packets received in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryMaxOnewayR2PDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.30
The maximum one-way destination to source delay(in microseconds) across all packets received in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryAvgOnewayR2PDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.31
The average one-way destination to source delay(in microseconds) across all packets received in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistorySumOnewayR2PDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.32
The total sum of one-way delay from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumOfSqOnewayR2PDelay		1.3.6.1.4.1.2544.1.12.8.1.8.1.33
The sum of square of one-way delay from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryMinPosP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.34
The minimum positive one-way jitter from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryMaxPosP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.35
The maximum positive one-way jitter from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryNumPosP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.36
The total number of positive one-way jitters from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumPosP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.37
The total sum of positive one-way jitters from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumOfSqPosP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.38
The sum of square of positive one-way jitters from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryMinNegP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.39
The minimum negative one-way jitter from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryMaxNegP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.40
The maximum negative one-way jitter from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryNumNegP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.41
The total number of negative one-way jitters from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumNegP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.42
The total sum of negative one-way jitters from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumOfSqNegP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.43
The sum of square of negative one-way jitters from source to destination in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryMinPosR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.44
The minimum positive one-way jitter from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryMaxPosR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.45
The maximum positive one-way jitter from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryNumPosR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.46
The total number of positive one-way jitters from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumPosR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.47
The total sum of positive one-way jitters from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumOfSqPosR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.48
The sum of square of positive one-way jitters from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryMinNegR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.49
The minimum negative one-way jitter from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryMaxNegR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.50
The maximum negative one-way jitter from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryNumNegR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.51
The total number of negative one-way jitters from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumNegR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.52
The total sum of negative one-way jitters from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumOfSqNegR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.53
The sum of square of negative one-way jitters from destination to source in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryY1731P2RNegLossOccurrences		1.3.6.1.4.1.2544.1.12.8.1.8.1.54
This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from Source MEP (Probe) to Destination MEP (Reflector). If these counts are non-zero then there could be some kind of provisioning mismatch between the Probe MEP and Reflector MEP. Here are some scenarios this can happen: - Probe MEP is configured to count in-profile frames only and the Reflector MEP is configured to count all frames with a mismatch in value for the attribute cfmMepLmCountInProfileFrames. - Probe MEP is configured to count data frames for specific VLAN priority and the Reflector MEP is configured to count data frames for all the priorities with a mismatch in values for the attributes cfmMepLmTxCountAllPrios or cfmMepLmRxCountAllPrios. NOTE: This could possibly happen due to reasons not related to configuration such as frame reordering in the network.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryY1731R2PNegLossOccurrences		1.3.6.1.4.1.2544.1.12.8.1.8.1.55
This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from to Destination MEP (Reflector) to Source MEP (Probe). If these counts are non-zero then there could be some kind of provisioning mismatch between the Probe MEP and Reflector MEP. Here are some scenarios this can happen: - Probe MEP is configured to count in-profile frames only and the Reflector MEP is configured to count all frames with a mismatch in value for the attribute cfmMepLmCountInProfileFrames. - Probe MEP is configured to count data frames for specific VLAN priority and the Reflector MEP is configured to count data frames for all the priorities with a mismatch in values for the attributes cfmMepLmTxCountAllPrios or cfmMepLmRxCountAllPrios. NOTE: This could possibly happen due to reasons not related to configuration such as frame reordering in the network.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryY1731RxLmSamples		1.3.6.1.4.1.2544.1.12.8.1.8.1.56
This attribute is only applicable to Y.1731 probes. This flag indicates that at least one loss measurement sample was received for this bin period (LMRs received). This is used by the user to differentiate between valid zero frame loss and not receiving any LMRs.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

esaProbeHistoryY1731RxDmSamples		1.3.6.1.4.1.2544.1.12.8.1.8.1.57
This attribute is only applicable to Y.1731 probes. This flag indicates that at least one delay measurement sample was received for this bin period (DMRs received).
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

esaProbeHistoryY1731P2RFrames		1.3.6.1.4.1.2544.1.12.8.1.8.1.58
This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Source MEP (Probe) that are transmitted towards the Destination MEP (Reflector). Based on the configuration the MEP counts the data frames with: - MEP's LM TX priority or all the priorities - All the VLAN IDs belonging the MEP's MA VID list.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryY1731R2PFrames		1.3.6.1.4.1.2544.1.12.8.1.8.1.59
This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Destination MEP (Reflector) that are transmitted towards the Source MEP (Probe). Based on the configuration the MEP counts the data frames with: - MEP's LM RX priority or all the priorities - All the VLAN IDs belonging the MEP's MA VID list.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryAvgAbsP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.60
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute P2R Jitter value. .
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryAvgAbsR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.61
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute R2P Jitter value. .
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryMinAbsP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.62
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute P2R Jitter value. .
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryMinAbsR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.63
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute R2P Jitter value. .
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryMaxAbsP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.64
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute P2R Jitter value. .
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryMaxAbsR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.65
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute R2P Jitter value. .
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

esaProbeHistoryNumAbsP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.66
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute P2R Jitters.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistoryNumAbsR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.67
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute R2P Jitters.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumAbsP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.68
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute P2R Jitter values.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumAbsR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.69
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute R2P Jitter values.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumOfSqAbsP2RJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.70
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute P2R Jitter values.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeHistorySumOfSqAbsR2PJitter		1.3.6.1.4.1.2544.1.12.8.1.8.1.71
This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute R2P Jitter values.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeDistStatsConfigTable		1.3.6.1.4.1.2544.1.12.8.1.9
A list of entries that need to be configured in order to obtain statistical distribution of ESA Probe collected data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsaProbeDistStatsConfigEntry

esaProbeDistStatsConfigEntry		1.3.6.1.4.1.2544.1.12.8.1.9.1
A row in the esaProbeDistStatsConfigTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	EsaProbeDistStatsConfigEntry

esaProbeDistStatsConfigIndex		1.3.6.1.4.1.2544.1.12.8.1.9.1.1
A unique index for each row. Each row corresponds to each enumeration type specified in EsaProbeDistStatsType.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..11

esaProbeDistStatsConfigType		1.3.6.1.4.1.2544.1.12.8.1.9.1.2
Indicates whether the statistical distribution is for round-trip delay (rt-delay), one-way probe to reflector delay (oneway-p2rdelay), one-way reflector to probe delay(oneway-r2pdelay), probe to reflector jitter (oneway-p2rjitter) or one-way reflector to probe jitter (oneway-r2pjitter).
Status: current	Access: read-only
OBJECT-TYPE
	EsaProbeDistStatsType

esaProbeDistStatsConfigMinVal		1.3.6.1.4.1.2544.1.12.8.1.9.1.3
Minimum sample value in distribution.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbeDistStatsConfigMaxVal		1.3.6.1.4.1.2544.1.12.8.1.9.1.4
Maximum sample value in distribution.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbeDistStatsConfigNumBins		1.3.6.1.4.1.2544.1.12.8.1.9.1.5
Number of distribution bins.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

esaProbeDistStatsConfigLowBoundOfBin1		1.3.6.1.4.1.2544.1.12.8.1.9.1.6
The lower bound of the 1st bin.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbeDistStatsConfigLowBoundOfBin2		1.3.6.1.4.1.2544.1.12.8.1.9.1.7
The lower bound of the 2nd bin.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbeDistStatsConfigLowBoundOfBin3		1.3.6.1.4.1.2544.1.12.8.1.9.1.8
The lower bound of the 3rd bin.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbeDistStatsConfigLowBoundOfBin4		1.3.6.1.4.1.2544.1.12.8.1.9.1.9
The lower bound of the 4th bin.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbeDistStatsConfigLowBoundOfBin5		1.3.6.1.4.1.2544.1.12.8.1.9.1.10
The lower bound of the 5th bin.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbeDistStatsConfigLowBoundOfBin6		1.3.6.1.4.1.2544.1.12.8.1.9.1.11
The lower bound of the 6th bin.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbeDistStatsConfigLowBoundOfBin7		1.3.6.1.4.1.2544.1.12.8.1.9.1.12
The lower bound of the 7th bin.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbeDistStatsConfigLowBoundOfBin8		1.3.6.1.4.1.2544.1.12.8.1.9.1.13
The lower bound of the 8th bin.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbeDistStatsConfigLowBoundOfBin9		1.3.6.1.4.1.2544.1.12.8.1.9.1.14
The lower bound of the 9th bin.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

esaProbeDistStatsTable		1.3.6.1.4.1.2544.1.12.8.1.10
A list of entries that provide statistical distribution of ESA Probe collected data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsaProbeDistStatsEntry

esaProbeDistStatsEntry		1.3.6.1.4.1.2544.1.12.8.1.10.1
A row in the esaProbeDistStatsTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	EsaProbeDistStatsEntry

esaProbeDistStatsDestinationIndex		1.3.6.1.4.1.2544.1.12.8.1.10.1.1
An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since only point-to-point SLA is supported.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeDistStatsCOSIndex		1.3.6.1.4.1.2544.1.12.8.1.10.1.2
An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly specified in the Probe parameters.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeDistStatsAction		1.3.6.1.4.1.2544.1.12.8.1.10.1.3
Allows the Manager to clear the bin.
Status: current	Access: read-write
OBJECT-TYPE
	CmPmBinAction

esaProbeDistStatsCOS		1.3.6.1.4.1.2544.1.12.8.1.10.1.4
The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported.
Status: current	Access: read-only
OBJECT-TYPE
	ClassOfServiceType

esaProbeDistStatsNumBins		1.3.6.1.4.1.2544.1.12.8.1.10.1.5
Number of bins over which the statistical data is distributed.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeDistStatsLTMin		1.3.6.1.4.1.2544.1.12.8.1.10.1.6
Number of sample data points which are less than the minimum value specified.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeDistStatsGTMax		1.3.6.1.4.1.2544.1.12.8.1.10.1.7
Number of sample data points which are greater than the maximum value specified.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeDistStatsBinTable		1.3.6.1.4.1.2544.1.12.8.1.11
A list of entries that provide statistical distribution of ESA Probe collected data for specific BINs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsaProbeDistStatsBinEntry

esaProbeDistStatsBinEntry		1.3.6.1.4.1.2544.1.12.8.1.11.1
A row in the esaProbeDistStatsBinTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	EsaProbeDistStatsBinEntry

esaProbeDistStatsBinIndex		1.3.6.1.4.1.2544.1.12.8.1.11.1.1
An index for each row that uniquely provides statistical data for a range.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

esaProbeDistStatsBinLower		1.3.6.1.4.1.2544.1.12.8.1.11.1.2
The lower limit of values collected in this bin.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeDistStatsBinUpper		1.3.6.1.4.1.2544.1.12.8.1.11.1.3
The upper limit of values collected in this bin.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeDistStatsBinNumSamples		1.3.6.1.4.1.2544.1.12.8.1.11.1.4
Number of sample data points which fall between the lower and upper limits.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeDistHistoryTable		1.3.6.1.4.1.2544.1.12.8.1.12
A list of entries that provide statistical distribution history of ESA Probe collected data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsaProbeDistHistoryEntry

esaProbeDistHistoryEntry		1.3.6.1.4.1.2544.1.12.8.1.12.1
A row in the esaProbeDistHistoryTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	EsaProbeDistHistoryEntry

esaProbeDistHistoryDestinationIndex		1.3.6.1.4.1.2544.1.12.8.1.12.1.1
An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since only point-to-point SLA is supported.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeDistHistoryCOSIndex		1.3.6.1.4.1.2544.1.12.8.1.12.1.2
An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly specified in the Probe parameters.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeDistHistoryIndex		1.3.6.1.4.1.2544.1.12.8.1.12.1.3
An arbitrary integer index value used to uniquely identify this ESA Probe Distribution History entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

esaProbeDistHistoryTime		1.3.6.1.4.1.2544.1.12.8.1.12.1.4
Indicates the time of history bin creation.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

esaProbeDistHistoryAction		1.3.6.1.4.1.2544.1.12.8.1.12.1.5
Allows the Manager to clear the bin.
Status: current	Access: read-write
OBJECT-TYPE
	CmPmBinAction

esaProbeDistHistoryCOS		1.3.6.1.4.1.2544.1.12.8.1.12.1.6
The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported.
Status: current	Access: read-only
OBJECT-TYPE
	ClassOfServiceType

esaProbeDistHistoryNumBins		1.3.6.1.4.1.2544.1.12.8.1.12.1.7
Number of bins over which the statistical data is distributed.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeDistHistoryLTMin		1.3.6.1.4.1.2544.1.12.8.1.12.1.8
Number of sample data points which are less than the minimum value specified.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeDistHistoryGTMax		1.3.6.1.4.1.2544.1.12.8.1.12.1.9
Number of sample data points which are greater than the maximum value specified.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeDistHistoryBinTable		1.3.6.1.4.1.2544.1.12.8.1.13
A list of entries that provide historical statistical distribution of ESA Probe collected data for specific BINs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsaProbeDistHistoryBinEntry

esaProbeDistHistoryBinEntry		1.3.6.1.4.1.2544.1.12.8.1.13.1
A row in the esaProbeDistHistoryBinTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	EsaProbeDistHistoryBinEntry

esaProbeDistHistoryBinIndex		1.3.6.1.4.1.2544.1.12.8.1.13.1.1
An index for each row that uniquely provides statistical data for a range.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

esaProbeDistHistoryBinLower		1.3.6.1.4.1.2544.1.12.8.1.13.1.2
The lower limit of values collected in this bin.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeDistHistoryBinUpper		1.3.6.1.4.1.2544.1.12.8.1.13.1.3
The upper limit of values collected in this bin.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

esaProbeDistHistoryBinNumSamples		1.3.6.1.4.1.2544.1.12.8.1.13.1.4
Number of sample data points which fall between the lower and upper limits.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeStatsThresholdTable		1.3.6.1.4.1.2544.1.12.8.1.14
A table of entries that allow manageability of ESA Probe Thresholds.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsaProbeStatsThresholdEntry

esaProbeStatsThresholdEntry		1.3.6.1.4.1.2544.1.12.8.1.14.1
A conceptual row in the esaProbeStatsThresholdTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	EsaProbeStatsThresholdEntry

esaProbeStatsThresholdIndex		1.3.6.1.4.1.2544.1.12.8.1.14.1.1
An index that uniquely identifies an entry in the esaProbeStatsThresholdTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

esaProbeStatsThresholdVariable		1.3.6.1.4.1.2544.1.12.8.1.14.1.2
The object identifier of the particular variable to be sampled. Objects of the esaProbeStatsTable table are monitored. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter32, PerfCounter64, Gauge, or TimeTicks) may be sampled.
Status: current	Access: read-only
OBJECT-TYPE
	VariablePointer

esaProbeStatsThresholdAbsValueLo		1.3.6.1.4.1.2544.1.12.8.1.14.1.3
Lower 32 bits of the absolute value of the threshold.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

esaProbeStatsThresholdAbsValueHi		1.3.6.1.4.1.2544.1.12.8.1.14.1.4
Higher 32 bits of the absolute value of the threshold.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

esaProbeStatsThresholdMonValue		1.3.6.1.4.1.2544.1.12.8.1.14.1.5
Monitored value corresponding to esaProbeStatsThresholdVariable.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

esaProbeCOSConfigTable		1.3.6.1.4.1.2544.1.12.8.1.15
A list of entries corresponding to ESA Probes COS Configuration Levels.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsaProbeCOSConfigEntry

esaProbeCOSConfigEntry		1.3.6.1.4.1.2544.1.12.8.1.15.1
A row in the esaProbeCOSConfigTable. Entries can be created in this table by management application action.
Status: current	Access: not-accessible
OBJECT-TYPE
	EsaProbeCOSConfigEntry

esaProbeCOSConfigIndex		1.3.6.1.4.1.2544.1.12.8.1.15.1.1
An integer index value used to uniquely identify SLA (Service Level Agreement) for a specific Class of Service. Index 1 is associated with cos-0, index 2 with cos-1, index 3 with cos-2 and so on.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..8

esaProbeCOSConfigType		1.3.6.1.4.1.2544.1.12.8.1.15.1.2
This is the Class of Service Type for Y.1731/SLM-SLR Probes, associated with the row.
Status: current	Access: read-create
OBJECT-TYPE
	ClassOfServiceType

esaProbeCOSConfigInterval		1.3.6.1.4.1.2544.1.12.8.1.15.1.3
This is the Class of Service Y.1731/SLM-SLR packet interval type.
Status: current	Access: read-create
OBJECT-TYPE
	EsaProbePktIntervalType

esaProbeCOSConfigPktSize		1.3.6.1.4.1.2544.1.12.8.1.15.1.4
This is the Class of Service Y.1731/SLM-SLR Packet Size. This object enables specification of the TLV size for Delay Measurement Measures(DMMs) as well as Synthetic Loss Measurement Frames (SLMs).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	64..9612

esaProbeCOSConfigStorageType		1.3.6.1.4.1.2544.1.12.8.1.15.1.5
The type of storage configured for this entry.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

esaProbeCOSConfigRowStatus		1.3.6.1.4.1.2544.1.12.8.1.15.1.6
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaProbeCOSConfigRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaProbeCOSConfigRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaProbeCOSConfigRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

esaProbeCOSConfigslmInterval		1.3.6.1.4.1.2544.1.12.8.1.15.1.7
This allows specification of the interval between subsequent SLM packets.
Status: current	Access: read-create
OBJECT-TYPE
	EsaProbePktIntervalType

esaProbeCOSConfigslmPktSize		1.3.6.1.4.1.2544.1.12.8.1.15.1.8
This allows specification of the SLM Packet Size.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

esaProbeCOSConfigSoamPmExtAvailFlrThreshold		1.3.6.1.4.1.2544.1.12.8.1.15.1.9
Frame loss ratio threshold for Availability (m%).
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..100000

esaProbeCOSConfigSoamPmExtFlrDeltaTNumLmPdus		1.3.6.1.4.1.2544.1.12.8.1.15.1.10
This is the number of loss measurement PDUs. delta_t is this attribute multiplied by the loss measurement message period. For example, if SLM message period is 100ms and this attribute is 10, then the delta_t is 1second.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..1000000

esaProbeCOSConfigSoamPmExtConDeltaTsForAvail		1.3.6.1.4.1.2544.1.12.8.1.15.1.11
This is the number of consecutive delta_ts used in the computation of availability/unavailability (n).
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..1000

esaProbeMultiDestinationTable		1.3.6.1.4.1.2544.1.12.8.1.16
A list of entries corresponding to ESA Probes Multi Destinations.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsaProbeMultiDestinationEntry

esaProbeMultiDestinationEntry		1.3.6.1.4.1.2544.1.12.8.1.16.1
A row in the esaProbeMultiDestinationTable. Entries can be created in this table by management application action. Entries in this table represent destinations in a point-to-multipoint ESA Probe.
Status: current	Access: not-accessible
OBJECT-TYPE
	EsaProbeMultiDestinationEntry

esaProbeDestinationIndex		1.3.6.1.4.1.2544.1.12.8.1.16.1.1
An integer index value used to uniquely identify a destination.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

esaProbeDestinationMepType		1.3.6.1.4.1.2544.1.12.8.1.16.1.2
This attribute is applicable only for point-to-multipoint probes. This indicates if the destination MEP is specified using the MEP ID object esaProbeDestinationMepId.
Status: current	Access: read-create
OBJECT-TYPE
	MepDestinationType

esaProbeDestinationMepMacAddr		1.3.6.1.4.1.2544.1.12.8.1.16.1.3
This attribute is applicable only for point-to-multipoint probes. It identifies the destination MEP. This MAC address will be the destination MAC address for frames if esaProbeDestinationMepType is 'macaddress'. If CC protocol is not enabled between source and destination MEP then this is the only choice to identify the remote MEP.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

esaProbeDestinationMepId		1.3.6.1.4.1.2544.1.12.8.1.16.1.4
This attribute is applicable only for point-to-multipoint probes. It identifies the destination MEP. The MAC address of this RMEP ID from RMEP database will be the destination MAC address. This value is used only if the esaProbeDestinationMepType is 'mepid'. CC protocol must be enabled between source and destination MEP if the RMEP ID is used to identify the Remote MEP.
Status: current	Access: read-create
OBJECT-TYPE
	Dot1agCfmMepIdOrZero

esaProbeDestinationStorageType		1.3.6.1.4.1.2544.1.12.8.1.16.1.5
The type of storage configured for this entry.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

esaProbeDestinationRowStatus		1.3.6.1.4.1.2544.1.12.8.1.16.1.6
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of esaProbeDestinationRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with esaProbeDestinationRowStatus value as createAndGo(4). Upon successful row creation, this variable has a value of active(1). The esaProbeDestinationRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

bertControlTable		1.3.6.1.4.1.2544.1.12.8.1.17
A list of entries for the control of BERT Streams.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BertControlEntry

bertControlEntry		1.3.6.1.4.1.2544.1.12.8.1.17.1
A conceptual row in the bertControlTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	BertControlEntry

bertControlIndex		1.3.6.1.4.1.2544.1.12.8.1.17.1.1
An arbitrary integer index value used to uniquely identify this BERT Control.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

bertControlSourceEntity		1.3.6.1.4.1.2544.1.12.8.1.17.1.2
Pointer to the entity on which the BERT will be started within a card.
Status: current	Access: read-write
OBJECT-TYPE
	VariablePointer

bertControlTestMode		1.3.6.1.4.1.2544.1.12.8.1.17.1.3
The mode of BERT to be performed.
Status: current	Access: read-write
OBJECT-TYPE
	BerTestMode

bertControlDuration		1.3.6.1.4.1.2544.1.12.8.1.17.1.4
This object enables specification of the time in seconds for BERT. BERT will be stopped after the specified time interval is exhausted.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..259200

bertControlStream		1.3.6.1.4.1.2544.1.12.8.1.17.1.5
This object specifies which stream should be included in the BERT execution. Value of 0 indicates that no streams is selected by bertControlStream. Non 0 value indicates the selected BERT stream.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

bertControlAction		1.3.6.1.4.1.2544.1.12.8.1.17.1.6
This object enables starting/stopping of traffic generation as well as resetting of monitored streams. This object may not be specified at configuration creation time - in this case it will take the value of `none'. This allows manager to explicitly control the start and stop of traffic generation/monitoring activity. Value of `stop' is invalid if the activity is specified but not started. Value of `start' is valid during creation time, as well as when activity is already stopped. Specification of `reset' resets the specified streams to default values, as well as clears the control specification. Get on this variable gives the most recent SNMP set specification.
Status: current	Access: read-write
OBJECT-TYPE
	BertControlAction

bertControlTestStatus		1.3.6.1.4.1.2544.1.12.8.1.17.1.7
This object reflects the current status of test set configuration entry. Upon creation, the status has a value of `initial'; the status changes to `in-progress' upon ecpaControlAction indicating `start'; the status changes to `completed' upon ecpaControlAction indicating stop, as well as when the specified test generation completes autonomously upon completion of number of frames or completion of specified time interval.
Status: current	Access: read-only
OBJECT-TYPE
	BerTestStatus

bertConfigStreamTable		1.3.6.1.4.1.2544.1.12.8.1.18
A list of entries for the configuration of BERT Config Stream Specifications.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BertConfigStreamEntry

bertConfigStreamEntry		1.3.6.1.4.1.2544.1.12.8.1.18.1
A conceptual row in the bertConfigStreamTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	BertConfigStreamEntry

bertConfigStreamIndex		1.3.6.1.4.1.2544.1.12.8.1.18.1.1
An arbitrary integer index value used to uniquely identify this BERT configStream.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

bertConfigStreamName		1.3.6.1.4.1.2544.1.12.8.1.18.1.2
Symbolic Stream Name that can be associated with an BERT Config stream.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

bertConfigStreamTxPattern		1.3.6.1.4.1.2544.1.12.8.1.18.1.3
Allows specification of the Tx pattern of this BERT Config stream.
Status: current	Access: read-write
OBJECT-TYPE
	BertPattern

bertConfigStreamErrInjectEnabled		1.3.6.1.4.1.2544.1.12.8.1.18.1.4
This object allows specification of whether Bit Error be injected.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

bertConfigStreamErrInjectRate		1.3.6.1.4.1.2544.1.12.8.1.18.1.5
Bit Error Rate, applicable when Error Injection is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	BitErrRate

bertConfigStreamErrInjectRateMultiplier		1.3.6.1.4.1.2544.1.12.8.1.18.1.6
BER value with 0.1 Step, in this release is fixed 10, only applicable when Error Injection is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

bertConfigStreamUserPatternLength		1.3.6.1.4.1.2544.1.12.8.1.18.1.7
User defined testing pattern length.
Status: current	Access: read-write
OBJECT-TYPE
	BertUserPatternLength

bertConfigStreamUserPattern		1.3.6.1.4.1.2544.1.12.8.1.18.1.8
User defined testing pattern in a HEX format display string, applicable when test pattern is user defined.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

bertTestStreamTable		1.3.6.1.4.1.2544.1.12.8.1.19
A list of entries containing results of a previous test.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BertTestStreamEntry

bertTestStreamEntry		1.3.6.1.4.1.2544.1.12.8.1.19.1
A conceptual row in the bertTestStreamTable. Entries in this table show results of the current BERT.
Status: current	Access: not-accessible
OBJECT-TYPE
	BertTestStreamEntry

bertTestStreamIndex		1.3.6.1.4.1.2544.1.12.8.1.19.1.1
An integer index value corresponding to the stream index for which the BERT was initiated.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

bertTestStreamName		1.3.6.1.4.1.2544.1.12.8.1.19.1.2
Symbolic Stream Name that can be associated with an BERT stream.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

bertTestStreamTxPattern		1.3.6.1.4.1.2544.1.12.8.1.19.1.3
Allows specification of the Tx pattern of this BERT Test stream.
Status: current	Access: read-only
OBJECT-TYPE
	BertPattern

bertTestStreamErrInjectEnabled		1.3.6.1.4.1.2544.1.12.8.1.19.1.4
This object allows specification of whether Bit Error be injected.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

bertTestStreamErrInjectRate		1.3.6.1.4.1.2544.1.12.8.1.19.1.5
Bit Error Rate, applicable when Error Injection is enabled.
Status: current	Access: read-only
OBJECT-TYPE
	BitErrRate

bertTestStreamErrInjectRateMultiplier		1.3.6.1.4.1.2544.1.12.8.1.19.1.6
BER value with 0.1 Step, in this release is fixed 10, only applicable when Error Injection is enabled.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bertTestStreamUserPatternLength		1.3.6.1.4.1.2544.1.12.8.1.19.1.7
User defined testing pattern length.
Status: current	Access: read-only
OBJECT-TYPE
	BertUserPatternLength

bertTestStreamUserPattern		1.3.6.1.4.1.2544.1.12.8.1.19.1.8
User defined testing pattern in a HEX format display string, applicable when test pattern is user defined.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

bertTestStreamMonStartTime		1.3.6.1.4.1.2544.1.12.8.1.19.1.9
The start time of the BERT for this stream.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

bertTestStreamMonEndTime		1.3.6.1.4.1.2544.1.12.8.1.19.1.10
The end time of the BERT for this stream.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

bertTestStreamMonElapsedTime		1.3.6.1.4.1.2544.1.12.8.1.19.1.11
The elapsed time of BERT for this stream in seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bertTestStreamMonSyncState		1.3.6.1.4.1.2544.1.12.8.1.19.1.12
The Sync State of the BERT.
Status: current	Access: read-only
OBJECT-TYPE
	BertSyncState

bertTestStreamMonRxPattern		1.3.6.1.4.1.2544.1.12.8.1.19.1.13
Allows specification of the Rx pattern of this BERT Test stream.
Status: current	Access: read-only
OBJECT-TYPE
	BertPattern

bertTestStreamMonSyncCounts		1.3.6.1.4.1.2544.1.12.8.1.19.1.14
Allows specification of the Sync counts from test start.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

bertTestStreamMonRxBitErrsSinceStart		1.3.6.1.4.1.2544.1.12.8.1.19.1.15
Allows specification of the Received Errors since test start.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

bertTestStreamMonRxBitsSinceStart		1.3.6.1.4.1.2544.1.12.8.1.19.1.16
Allows specification of the Received Bits since test start.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

bertTestStreamMonRxESsSinceStart		1.3.6.1.4.1.2544.1.12.8.1.19.1.17
Allows specification of the Error seconds since test start.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

bertTestStreamMonRxErrRateSinceStart		1.3.6.1.4.1.2544.1.12.8.1.19.1.18
Allows specification of the Received BER Unit since test start.
Status: current	Access: read-only
OBJECT-TYPE
	BitErrRate

bertTestStreamMonRxErrRateMultiplierSinceStart		1.3.6.1.4.1.2544.1.12.8.1.19.1.19
Allows specification of the Received BER value with 0.1 Step since test start.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bertTestStreamMonRxBitErrsSinceLastSync		1.3.6.1.4.1.2544.1.12.8.1.19.1.20
Allows specification of the Received Errors since last sync.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

bertTestStreamMonRxBitsSinceLastSync		1.3.6.1.4.1.2544.1.12.8.1.19.1.21
Allows specification of the Received Bits since last sync.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

bertTestStreamMonRxESsSinceLastSync		1.3.6.1.4.1.2544.1.12.8.1.19.1.22
Allows specification of the Received Error seconds since last sync.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

bertTestStreamMonRxErrRateSinceLastSync		1.3.6.1.4.1.2544.1.12.8.1.19.1.23
Allows specification of the Received BER Unit since last sync.
Status: current	Access: read-only
OBJECT-TYPE
	BitErrRate

bertTestStreamMonRxErrRateMultiplierSinceLastSync		1.3.6.1.4.1.2544.1.12.8.1.19.1.24
Allows specification of the Received BER value with 0.1 Step since last sync.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

bertTestStreamConfigChangedFlag		1.3.6.1.4.1.2544.1.12.8.1.19.1.25
This object provides information on whether the associated bertConfigStream is changed.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

bertTestStreamMonOOSSsSinceStart		1.3.6.1.4.1.2544.1.12.8.1.19.1.26
This object means the Out of Sync Seconds since start.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

f3EsaProbeCOSConfigSoamPmExtTable		1.3.6.1.4.1.2544.1.12.8.1.20
A list of entries corresponding to ESA Probe Cos Configurations MEF 35.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		F3EsaProbeCOSConfigSoamPmExtEntry

f3EsaProbeCOSConfigSoamPmExtEntry		1.3.6.1.4.1.2544.1.12.8.1.20.1
A row in the esaProbeCOSConfigTable MEF 35. Entries can be created in this table by management application action.
Status: current	Access: not-accessible
OBJECT-TYPE
	F3EsaProbeCOSConfigSoamPmExtEntry

f3EsaProbeCOSConfigSoamPmExtAvailFlrThreshold		1.3.6.1.4.1.2544.1.12.8.1.20.1.1
Frame loss ratio threshold for Availability (m%).
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..100000

f3EsaProbeCOSConfigSoamPmExtFlrDeltaTNumLmPdus		1.3.6.1.4.1.2544.1.12.8.1.20.1.2
This is the number of loss measurement PDUs. delta_t is this attribute multiplied by the loss measurement message period. For example, if SLM message period is 100ms and this attribute is 10, then the delta_t is 1second.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..1000000

f3EsaProbeCOSConfigSoamPmExtConDeltaTsForAvail		1.3.6.1.4.1.2544.1.12.8.1.20.1.3
This is the number of consecutive delta_ts used in the computation of availability/unavailability (n).
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..1000

f3EsaProbeStatsSoamPmExtTable		1.3.6.1.4.1.2544.1.12.8.1.21
A collection of ESA Probe MEF 35 related statistics kept for a particular ESA Probe entity. These reflect the current data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		F3EsaProbeStatsSoamPmExtEntry

f3EsaProbeStatsSoamPmExtEntry		1.3.6.1.4.1.2544.1.12.8.1.21.1
A conceptual row in the f3EsaProbeStatsSoamPmExtTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	F3EsaProbeStatsSoamPmExtEntry

f3EsaProbeStatsSoamPmExtMinP2RFlr		1.3.6.1.4.1.2544.1.12.8.1.21.1.1
This is the minimum probe to reflector FLR (m%).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtMaxP2RFlr		1.3.6.1.4.1.2544.1.12.8.1.21.1.2
This is the maximum probe to reflector FLR (m%).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtAvgP2RFlr		1.3.6.1.4.1.2544.1.12.8.1.21.1.3
This is the average probe to reflector FLR (m%).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtMinR2PFlr		1.3.6.1.4.1.2544.1.12.8.1.21.1.4
This is the minimum reflector to probe FLR (m%).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtMaxR2PFlr		1.3.6.1.4.1.2544.1.12.8.1.21.1.5
This is the maximum reflector to probe FLR (m%).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtAvgR2PFlr		1.3.6.1.4.1.2544.1.12.8.1.21.1.6
This is the average reflector to probe FLR (m%).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtP2rSeverelyErroredDeltaTs		1.3.6.1.4.1.2544.1.12.8.1.21.1.7
This is the number of delta_ts in which the FLR is greater than availability threshold in the probe to reflector direction.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtR2PSeverelyErroredDeltaTs		1.3.6.1.4.1.2544.1.12.8.1.21.1.8
This is the number of delta_ts in which the FLR is greater than availability threshold in the reflector to probe direction.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtP2rAvailableTime		1.3.6.1.4.1.2544.1.12.8.1.21.1.9
This is the probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is greater than availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtR2PAvailableTime		1.3.6.1.4.1.2544.1.12.8.1.21.1.10
This is the reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is greater than availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtP2rUnavailableTime		1.3.6.1.4.1.2544.1.12.8.1.21.1.11
This is the probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtR2PUnavailableTime		1.3.6.1.4.1.2544.1.12.8.1.21.1.12
This is the reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtMinAbsRTJitter		1.3.6.1.4.1.2544.1.12.8.1.21.1.13
Minimum absolute round-trip (two-way) jitter in a measurement interval (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtMaxAbsRTJitter		1.3.6.1.4.1.2544.1.12.8.1.21.1.14
Maximum absolute round-trip (two-way) jitter in a measurement interval (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtAvgAbsRTJitter		1.3.6.1.4.1.2544.1.12.8.1.21.1.15
Average absolute round-trip (two-way) jitter in a measurement interval (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtNumAbsRTJitter		1.3.6.1.4.1.2544.1.12.8.1.21.1.16
Number of absolute round-trip (two-way) jitter samples (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtSumAbsRTJitter		1.3.6.1.4.1.2544.1.12.8.1.21.1.17
Sum of absolute round-trip (two-way) jitter samples (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtSumOfSqAbsRTJitter		1.3.6.1.4.1.2544.1.12.8.1.21.1.18
Sum of squares of absolute round-trip (two-way) jitter samples (microseconds^2).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtMaxP2RFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.19
Maximum P2R (Forward) FDR in a measurement interval (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtAvgP2RFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.20
Average P2R (Forward) FDR in a measurement interval (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtNumP2RFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.21
Number of P2R (Forward) FDR samples (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtSumP2RFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.22
Sum of P2R (Forward) FDR samples (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtSumOfSqP2RFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.23
Sum of squares of P2R (Forward) FDR samples (microseconds^2).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtMaxR2PFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.24
Maximum R2P (Backward) FDR in a measurement interval (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtAvgR2PFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.25
Average R2P (Backward) FDR in a measurement interval (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtNumR2PFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.26
Number of R2P (Backward) FDR samples (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtSumR2PFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.27
Sum of R2P (Backward) FDR samples (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtSumOfSqR2PFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.28
Sum of squares of R2P (Backward) FDR samples (microseconds^2).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtMaxRTFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.29
Maximum round-trip (two-way) FDR in a measurement interval (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtAvgRTFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.30
Average round-trip (two-way) FDR in a measurement interval (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtNumRTFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.31
Number of round-trip (two-way) FDR samples (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtSumRTFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.32
Sum of round-trip (two-way) FDR samples (microseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtSumOfSqRTFDR		1.3.6.1.4.1.2544.1.12.8.1.21.1.33
Sum of squares of round-trip (two-way) FDR samples (microseconds^2).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtP2rAvailableDeltaTs		1.3.6.1.4.1.2544.1.12.8.1.21.1.34
Probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtR2pAvailableDeltaTs		1.3.6.1.4.1.2544.1.12.8.1.21.1.35
Reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtP2rUnavailableDeltaTs		1.3.6.1.4.1.2544.1.12.8.1.21.1.36
Probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtR2pUnavailableDeltaTs		1.3.6.1.4.1.2544.1.12.8.1.21.1.37
Reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeStatsSoamPmExtElapsedTime		1.3.6.1.4.1.2544.1.12.8.1.21.1.38
The elapsed time (monotonic time) for the interval which could be less or more than measurement interval based on which the Time of Day was moved forward or backwards respectively (miliseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtTable		1.3.6.1.4.1.2544.1.12.8.1.22
A collection of ESA Probe MEF 35 related history kept for a particular ESA Probe entity. These reflect the history data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		F3EsaProbeHistorySoamPmExtEntry

f3EsaProbeHistorySoamPmExtEntry		1.3.6.1.4.1.2544.1.12.8.1.22.1
A conceptual row in the f3EsaProbeHistorySoamPmExtTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	F3EsaProbeHistorySoamPmExtEntry

f3EsaProbeHistorySoamPmExtMinP2RFlr		1.3.6.1.4.1.2544.1.12.8.1.22.1.1
This is the minimum probe to reflector FLR.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtMaxP2RFlr		1.3.6.1.4.1.2544.1.12.8.1.22.1.2
This is the maximum probe to reflector FLR.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtAvgP2RFlr		1.3.6.1.4.1.2544.1.12.8.1.22.1.3
This is the average probe to reflector FLR.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtMinR2PFlr		1.3.6.1.4.1.2544.1.12.8.1.22.1.4
This is the minimum reflector to probe FLR.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtMaxR2PFlr		1.3.6.1.4.1.2544.1.12.8.1.22.1.5
This is the maximum reflector to probe FLR.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtAvgR2PFlr		1.3.6.1.4.1.2544.1.12.8.1.22.1.6
This is the average reflector to probe FLR.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtP2rSeverelyErroredDeltaTs		1.3.6.1.4.1.2544.1.12.8.1.22.1.7
This is the number of delta_ts in which the FLR is greater than availability threshold in the probe to reflector direction.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtR2PSeverelyErroredDeltaTs		1.3.6.1.4.1.2544.1.12.8.1.22.1.8
This is the number of delta_ts in which the FLR is greater than availability threshold in the reflector to probe direction.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtP2rAvailableTime		1.3.6.1.4.1.2544.1.12.8.1.22.1.9
This is the probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is greater than availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtR2PAvailableTime		1.3.6.1.4.1.2544.1.12.8.1.22.1.10
This is the reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is greater than availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtP2rUnavailableTime		1.3.6.1.4.1.2544.1.12.8.1.22.1.11
This is the probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtR2PUnavailableTime		1.3.6.1.4.1.2544.1.12.8.1.22.1.12
This is the reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It is incremented until FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtMinAbsRTJitter		1.3.6.1.4.1.2544.1.12.8.1.22.1.13
Minimum absolute round-trip (two-way) jitter in a measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtMaxAbsRTJitter		1.3.6.1.4.1.2544.1.12.8.1.22.1.14
Maximum absolute round-trip (two-way) jitter in a measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtAvgAbsRTJitter		1.3.6.1.4.1.2544.1.12.8.1.22.1.15
Average absolute round-trip (two-way) jitter in a measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtNumAbsRTJitter		1.3.6.1.4.1.2544.1.12.8.1.22.1.16
Number of absolute round-trip (two-way) jitter samples.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtSumAbsRTJitter		1.3.6.1.4.1.2544.1.12.8.1.22.1.17
Sum of absolute round-trip (two-way) jitter samples.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtSumOfSqAbsRTJitter		1.3.6.1.4.1.2544.1.12.8.1.22.1.18
Sum of squares of absolute round-trip (two-way) jitter samples.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtMaxP2RFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.19
Maximum P2R (Forward) FDR in a measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtAvgP2RFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.20
Average P2R (Forward) FDR in a measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtNumP2RFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.21
Number of P2R (Forward) FDR samples.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtSumP2RFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.22
Sum of P2R (Forward) FDR samples.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtSumOfSqP2RFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.23
Sum of squares of P2R (Forward) FDR samples.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtMaxR2PFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.24
Maximum R2P (Backward) FDR in a measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtAvgR2PFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.25
Average R2P (Backward) FDR in a measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtNumR2PFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.26
Number of R2P (Backward) FDR samples.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtSumR2PFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.27
Sum of R2P (Backward) FDR samples.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtSumOfSqR2PFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.28
Sum of squares of R2P (Backward) FDR samples.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtMaxRTFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.29
Maximum round-trip (two-way) FDR in a measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtAvgRTFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.30
Average round-trip (two-way) FDR in a measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtNumRTFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.31
Number of round-trip (two-way) FDR samples.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtSumRTFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.32
Sum of round-trip (two-way) FDR samples.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtSumOfSqRTFDR		1.3.6.1.4.1.2544.1.12.8.1.22.1.33
Sum of squares of round-trip (two-way) FDR samples.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtP2rAvailableDeltaTs		1.3.6.1.4.1.2544.1.12.8.1.22.1.34
Probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtR2pAvailableDeltaTs		1.3.6.1.4.1.2544.1.12.8.1.22.1.35
Reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtP2rUnavailableDeltaTs		1.3.6.1.4.1.2544.1.12.8.1.22.1.36
Probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtR2pUnavailableDeltaTs		1.3.6.1.4.1.2544.1.12.8.1.22.1.37
Reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

f3EsaProbeHistorySoamPmExtElapsedTime		1.3.6.1.4.1.2544.1.12.8.1.22.1.38
The elapsed time (monotonic time) for the interval which could be less or more than measurement interval based on which the Time of Day was moved forward or backwards respectively (miliseconds).
Status: current	Access: read-only
OBJECT-TYPE
	PerfCounter64

cmOperateLoopbackTrap		1.3.6.1.4.1.2544.1.12.8.2.1
This is the Operate Loopback Notification sent by the agent. The actual attribute value is sent by the agent in the form of a varbind list, as additional objects, as per SMIv2 (RFC2578, Section 8.1).
Status: current	Access: read-only
NOTIFICATION-TYPE

cmReleaseLoopbackTrap		1.3.6.1.4.1.2544.1.12.8.2.2
This is the Release Loopback Notification sent by the agent. The actual attribute value is sent by the agent in the form of a varbind list, as additional objects, as per SMIv2 (RFC2578, Section 8.1).
Status: current	Access: read-only
NOTIFICATION-TYPE

esaProbeThresholdCrossingAlert		1.3.6.1.4.1.2544.1.12.8.2.3
This trap is sent each time a threshold on a PM condition on ESA Probe is crossed.
Status: current	Access: read-only
NOTIFICATION-TYPE

cmServAssuranceCompliances		1.3.6.1.4.1.2544.1.12.8.3.1
OBJECT IDENTIFIER

cmServAssuranceGroups		1.3.6.1.4.1.2544.1.12.8.3.2
OBJECT IDENTIFIER

cmServAssuranceCompliance		1.3.6.1.4.1.2544.1.12.8.3.1.1
Describes the requirements for conformance to the CM ServAssurance group.
Status: current	Access: read-only
MODULE-COMPLIANCE

cmServAssuranceObjectGroup		1.3.6.1.4.1.2544.1.12.8.3.2.1
***************** THIS OBJECT GROUP IS NOW DEPRECATED *************** A collection of objects used to manage the CM ServAssurance group.
Status: deprecated	Access: read-only
OBJECT-GROUP

cmServAssuranceNotifGroup		1.3.6.1.4.1.2544.1.12.8.3.2.2
***************** THIS OBJECT GROUP IS NOW DEPRECATED ****************** A collection of notifications used in the CM ServAssurance group.
Status: deprecated	Access: read-only
NOTIFICATION-GROUP

cmEcpaGroup		1.3.6.1.4.1.2544.1.12.8.3.2.3
A collection of objects used to manage the CM ServAssurance ECPA functionality.
Status: current	Access: read-only
OBJECT-GROUP

cmEsaGroup		1.3.6.1.4.1.2544.1.12.8.3.2.4
A collection of objects used to manage the CM ServAssurance ESA functionality.
Status: current	Access: read-only
OBJECT-GROUP

cmServAssuranceGenNotifGroup		1.3.6.1.4.1.2544.1.12.8.3.2.5
A collection of notifications used in the generic CM ServAssurance functionality.
Status: current	Access: read-only
NOTIFICATION-GROUP

cmServAssuranceEsaNotifGroup		1.3.6.1.4.1.2544.1.12.8.3.2.6
A collection of notifications used in the CM ServAssurance ESA functionality.
Status: current	Access: read-only
NOTIFICATION-GROUP

cmBertGroup		1.3.6.1.4.1.2544.1.12.8.3.2.7
A collection of objects used to manage the CM ServAssurance BERT functionality.
Status: current	Access: read-only
OBJECT-GROUP