CLEARTRAC7-MIB

File: CLEARTRAC7-MIB.mib (560909 bytes)

Imported modules

RFC-1212 RFC1155-SMI RFC1213-MIB
RFC-1215

Imported symbols

OBJECT-TYPE enterprises IpAddress
Counter Gauge DisplayString
TRAP-TYPE

Defined Types

SysPosEntry  
SEQUENCE    
  sysPosId INTEGER
  sysPosProduct OBJECT IDENTIFIER
  sysPosRackId INTEGER
  sysPosIpAddr IpAddress

IpaddrEntry  
SEQUENCE    
  ipaddrIndex INTEGER
  ipaddrAddr IpAddress
  ipaddrType INTEGER
  ipaddrIfIndex INTEGER

ProxyEntry  
SEQUENCE    
  proxyIndex INTEGER
  proxyComm DisplayString
  proxyIpAddr IpAddress
  proxyIpMask IpAddress
  proxyTrapIpAddr IpAddress
  proxyDefaultGateway IpAddress

IntfEntry  
SEQUENCE    
  intfIndex INTEGER
  intfDesc DisplayString
  intfType INTEGER
  intfNumInType INTEGER
  intfSlot INTEGER
  intfSlotType INTEGER
  intfNumInSlot INTEGER
  intfModuleType INTEGER

SlotPortInSlotEntry  
SEQUENCE    
  slotSlot INTEGER
  slotPortInSlot INTEGER
  slotIfIndex INTEGER

IfwanEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanFallBackSpeed-bps INTEGER
  ifwanFallBackSpeedEnable INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanCoding INTEGER
  ifwanModem INTEGER
  ifwanTxStart INTEGER
  ifwanTxStartCop INTEGER
  ifwanTxStartPass INTEGER
  ifwanIdle INTEGER
  ifwanDuplex INTEGER
  ifwanGroupPoll INTEGER
  ifwanGroupAddress STRING Size(2)
  ifwanPollDelay-ms INTEGER
  ifwanFrameDelay INTEGER
  ifwanFormat INTEGER
  ifwanSync STRING Size(2)
  ifwanDropSyncCounter INTEGER
  ifwanDropSyncCharacter STRING Size(1)
  ifwanMode INTEGER
  ifwanBodCall-s INTEGER
  ifwanBodHang-s INTEGER
  ifwanBodLevel INTEGER
  ifwanBackupCall-s INTEGER
  ifwanBackupHang-s INTEGER
  ifwanDialTimeout-s INTEGER
  ifwanPortToBack INTEGER
  ifwanDialer INTEGER
  ifwanClassNumber INTEGER
  ifwanRingNumber STRING Size(2)
  ifwanIpAddress IpAddress
  ifwanSubnetMask IpAddress
  ifwanMaxFrame INTEGER
  ifwanIpRip INTEGER
  ifwanIpRipTxRx INTEGER
  ifwanIpRipAuthType INTEGER
  ifwanIpRipPassword DisplayString
  ifwanOspfEnable INTEGER
  ifwanOspfAreaId IpAddress
  ifwanOspfTransitDelay INTEGER
  ifwanOspfRetransmitInt INTEGER
  ifwanOspfHelloInt INTEGER
  ifwanOspfDeadInt INTEGER
  ifwanOspfPassword DisplayString
  ifwanOspfMetricCost INTEGER
  ifwanCompression INTEGER
  ifwanPriority INTEGER
  ifwanRemoteUnit DisplayString
  ifwanTimeout INTEGER
  ifwanRetry INTEGER
  ifwanRemotePort INTEGER
  ifwanFlowControl INTEGER
  ifwanMgmtInterface INTEGER
  ifwanEnquiryTimer-s INTEGER
  ifwanReportCycle INTEGER
  ifwanCllm INTEGER
  ifwanIpxRip INTEGER
  ifwanIpxSap INTEGER
  ifwanIpxNetNum STRING Size(4)
  ifwanRxFlow INTEGER
  ifwanTxFlow INTEGER
  ifwanTxHold-s INTEGER
  ifwanDsOSpeed-bps INTEGER
  ifwanFraming INTEGER
  ifwanTerminating INTEGER
  ifwanCrc4 INTEGER
  ifwanLineCoding INTEGER
  ifwanBChannels INTEGER
  ifwanMultiframing INTEGER
  ifwanGainLimit INTEGER
  ifwanSignaling INTEGER
  ifwanIdleCode STRING Size(1)
  ifwanLineBuild INTEGER
  ifwanT1E1Status INTEGER
  ifwanT1E1LoopBack INTEGER
  ifwanEncodingLaw INTEGER
  ifwanChExp DisplayString
  ifwanChUse DisplayString
  ifwanCellPacketization INTEGER
  ifwanMaxChannels INTEGER
  ifwanCondLMIPort INTEGER
  ifwanExtNumber DisplayString
  ifwanDestExtNumber DisplayString
  ifwanSvcAddressType INTEGER
  ifwanSvcNetworkAddress DisplayString
  ifwanSvcMaxTxTimeoutT200 INTEGER
  ifwanSvcInactiveTimeoutT203 INTEGER
  ifwanSvcIframeRetransmissionsN200 INTEGER
  ifwanSvcSetupTimeoutT303 INTEGER
  ifwanSvcDisconnectTimeoutT305 INTEGER
  ifwanSvcReleaseTimeoutT308 INTEGER
  ifwanSvcCallProceedingTimeoutT310 INTEGER
  ifwanSvcStatusTimeoutT322 INTEGER
  ifwanT1E1InterBit INTEGER
  ifwanConnTimeout-s INTEGER
  ifwanTeiMode INTEGER
  ifwanDigitNumber INTEGER
  ifwanMsn1 DisplayString
  ifwanMsn2 DisplayString
  ifwanMsn3 DisplayString
  ifwanX25Encapsulation INTEGER
  ifwanPvcNumber INTEGER
  ifwanQsigPbxAb INTEGER
  ifwanQsigPbxXy INTEGER
  ifwanPppSilent INTEGER
  ifwanPppConfigRestartTimer INTEGER
  ifwanPppConfigRetries INTEGER
  ifwanPppNegociateLocalMru INTEGER
  ifwanPppLocalMru INTEGER
  ifwanPppNegociatePeerMru INTEGER
  ifwanPppPeerMruUpTo INTEGER
  ifwanPppNegociateAccm INTEGER
  ifwanPppRequestedAccmChar STRING Size(4)
  ifwanPppAcceptAccmPeer INTEGER
  ifwanPppAcceptableAccmChar STRING Size(4)
  ifwanPppRequestMagicNum INTEGER
  ifwanPppAcceptMagicNum INTEGER
  ifwanPppAcceptOldIpAddNeg INTEGER
  ifwanPppNegociateIpAddress INTEGER
  ifwanPppAcceptIpAddress INTEGER
  ifwanPppRemoteIpAddress IpAddress
  ifwanPppRemoteSubnetMask IpAddress
  ifwanHighPriorityTransparentClass INTEGER
  ifwanTransparentClassNumber INTEGER
  ifwanChannelCompressed INTEGER
  ifwanSfType INTEGER
  ifwanSfMode INTEGER
  ifwanSfCarrierId INTEGER

IfwanShortEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanFallBackSpeed-bps INTEGER
  ifwanFallBackSpeedEnable INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER

IfwanT1Entry  
SEQUENCE    
  ifwanDsOSpeed-bps INTEGER
  ifwanChUse DisplayString
  ifwanFraming INTEGER
  ifwanTerminating INTEGER
  ifwanCrc4 INTEGER
  ifwanLineCoding INTEGER
  ifwanLineBuild INTEGER
  ifwanBChannels INTEGER
  ifwanMultiframing INTEGER

IfwanG703PortEntry  
SEQUENCE    
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanClocking INTEGER
  ifwanFraming INTEGER
  ifwanCrc4 INTEGER
  ifwanLineCoding INTEGER
  ifwanT1E1Status INTEGER
  ifwanChUse DisplayString
  ifwanLineBuild INTEGER
  ifwanT1E1LoopBack INTEGER

IfwanG703ChannelEntry  
SEQUENCE    
  ifwanDesc DisplayString
  ifwanChUse DisplayString
  ifwanProtocol INTEGER
  ifwanDsOSpeed-bps INTEGER
  ifwanMode INTEGER
  ifwanBodCall-s INTEGER
  ifwanBodHang-s INTEGER
  ifwanBodLevel INTEGER
  ifwanBackupCall-s INTEGER
  ifwanBackupHang-s INTEGER
  ifwanDialTimeout-s INTEGER
  ifwanPortToBack INTEGER
  ifwanClassNumber INTEGER
  ifwanRingNumber STRING Size(2)
  ifwanIpAddress IpAddress
  ifwanSubnetMask IpAddress
  ifwanMaxFrame INTEGER
  ifwanIpRip INTEGER
  ifwanIpRipTxRx INTEGER
  ifwanIpRipAuthType INTEGER
  ifwanIpRipPassword DisplayString
  ifwanOspfEnable INTEGER
  ifwanOspfAreaId IpAddress
  ifwanOspfTransitDelay INTEGER
  ifwanOspfRetransmitInt INTEGER
  ifwanOspfHelloInt INTEGER
  ifwanOspfDeadInt INTEGER
  ifwanOspfPassword DisplayString
  ifwanOspfMetricCost INTEGER
  ifwanCompression INTEGER
  ifwanPriority INTEGER
  ifwanRemoteUnit DisplayString
  ifwanTimeout INTEGER
  ifwanRetry INTEGER
  ifwanRemotePort INTEGER
  ifwanFlowControl INTEGER
  ifwanMgmtInterface INTEGER
  ifwanEnquiryTimer-s INTEGER
  ifwanReportCycle INTEGER
  ifwanCllm INTEGER
  ifwanIpxRip INTEGER
  ifwanIpxSap INTEGER
  ifwanIpxNetNum STRING Size(4)
  ifwanCellPacketization INTEGER
  ifwanCondLMIPort INTEGER

IfwanRxTICEICEntry  
SEQUENCE    
  ifwanCrc4 INTEGER
  ifwanLineCoding INTEGER
  ifwanT1E1InterBit INTEGER
  ifwanEncodingLaw INTEGER
  ifwanChExp DisplayString
  ifwanChUse DisplayString
  ifwanClocking INTEGER
  ifwanT1E1LoopBack INTEGER
  ifwanT1E1Status INTEGER
  ifwanLineBuild INTEGER
  ifwanIdleCode STRING Size(1)
  ifwanSignaling INTEGER
  ifwanFraming INTEGER
  ifwanGainLimit INTEGER
  ifwanRemoteUnit DisplayString
  ifwanExtNumber DisplayString
  ifwanDestExtNumber DisplayString
  ifwanConnTimeout-s INTEGER
  ifwanQsigPbxAb INTEGER
  ifwanQsigPbxXy INTEGER
  ifwanHighPriorityTransparentClass INTEGER
  ifwanTransparentClassNumber INTEGER
  ifwanChannelCompressed INTEGER

IfwanIsdnBriVoiceEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanTerminating INTEGER
  ifwanEncodingLaw INTEGER
  ifwanTeiMode INTEGER
  ifwanDigitNumber INTEGER
  ifwanMsn1 DisplayString
  ifwanMsn2 DisplayString
  ifwanMsn3 DisplayString

IfwanSdlcEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanFallBackSpeed-bps INTEGER
  ifwanFallBackSpeedEnable INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanCoding INTEGER
  ifwanModem INTEGER
  ifwanTxStart INTEGER
  ifwanIdle INTEGER
  ifwanDuplex INTEGER
  ifwanGroupPoll INTEGER
  ifwanGroupAddress STRING Size(2)
  ifwanPollDelay-ms INTEGER

IfwanHdlcEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanFallBackSpeed-bps INTEGER
  ifwanFallBackSpeedEnable INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanCoding INTEGER
  ifwanModem INTEGER
  ifwanTxStart INTEGER
  ifwanIdle INTEGER
  ifwanFrameDelay INTEGER
  ifwanRemoteUnit DisplayString
  ifwanClassNumber INTEGER
  ifwanRemotePort INTEGER
  ifwanDsOSpeed-bps INTEGER
  ifwanFraming INTEGER
  ifwanTerminating INTEGER
  ifwanCrc4 INTEGER
  ifwanLineCoding INTEGER
  ifwanBChannels INTEGER
  ifwanMultiframing INTEGER

IfwanDdcmpEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanFallBackSpeed-bps INTEGER
  ifwanFallBackSpeedEnable INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanModem INTEGER
  ifwanTxStart INTEGER
  ifwanRemoteUnit DisplayString
  ifwanClassNumber INTEGER
  ifwanRemotePort INTEGER

IfwanTAsyncEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanFormat INTEGER
  ifwanModem INTEGER
  ifwanRemoteUnit DisplayString
  ifwanClassNumber INTEGER
  ifwanRemotePort INTEGER

IfwanRAsyncEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanFormat INTEGER
  ifwanRxFlow INTEGER
  ifwanTxFlow INTEGER
  ifwanTxHold-s INTEGER
  ifwanRemoteUnit DisplayString
  ifwanClassNumber INTEGER
  ifwanRemotePort INTEGER

IfwanBscEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanFallBackSpeed-bps INTEGER
  ifwanFallBackSpeedEnable INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanModem INTEGER
  ifwanTxStart INTEGER
  ifwanRemoteUnit DisplayString
  ifwanClassNumber INTEGER
  ifwanRemotePort INTEGER

IfwanCopEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanFallBackSpeed-bps INTEGER
  ifwanFallBackSpeedEnable INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanModem INTEGER
  ifwanTxStartCop INTEGER
  ifwanIdle INTEGER
  ifwanFormat INTEGER
  ifwanSync STRING Size(2)
  ifwanDropSyncCounter INTEGER
  ifwanDropSyncCharacter STRING Size(1)
  ifwanRemoteUnit DisplayString
  ifwanClassNumber INTEGER
  ifwanRemotePort INTEGER

IfwanPvcrEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanMode INTEGER
  ifwanBodCall-s INTEGER
  ifwanBodHang-s INTEGER
  ifwanBodLevel INTEGER
  ifwanBackupCall-s INTEGER
  ifwanBackupHang-s INTEGER
  ifwanDialTimeout-s INTEGER
  ifwanPortToBack INTEGER
  ifwanDialer INTEGER
  ifwanRingNumber STRING Size(2)
  ifwanIpAddress IpAddress
  ifwanSubnetMask IpAddress
  ifwanIpRip INTEGER
  ifwanIpRipTxRx INTEGER
  ifwanIpRipAuthType INTEGER
  ifwanIpRipPassword DisplayString
  ifwanOspfEnable INTEGER
  ifwanOspfAreaId IpAddress
  ifwanOspfTransitDelay INTEGER
  ifwanOspfRetransmitInt INTEGER
  ifwanOspfHelloInt INTEGER
  ifwanOspfDeadInt INTEGER
  ifwanOspfPassword DisplayString
  ifwanOspfMetricCost INTEGER
  ifwanCompression INTEGER
  ifwanPriority INTEGER
  ifwanRemoteUnit DisplayString
  ifwanTimeout INTEGER
  ifwanRetry INTEGER
  ifwanIpxRip INTEGER
  ifwanIpxSap INTEGER
  ifwanIpxNetNum STRING Size(4)
  ifwanDsOSpeed-bps INTEGER
  ifwanFraming INTEGER
  ifwanTerminating INTEGER
  ifwanCrc4 INTEGER
  ifwanLineCoding INTEGER
  ifwanBChannels INTEGER
  ifwanMultiframing INTEGER
  ifwanMaxChannels INTEGER

IfwanPassthruEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanModem INTEGER
  ifwanTxStartPass INTEGER
  ifwanRemoteUnit DisplayString
  ifwanClassNumber INTEGER
  ifwanRemotePort INTEGER

IfwanFrNetEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanModem INTEGER
  ifwanFrameDelay INTEGER
  ifwanFallBackSpeed-bps INTEGER
  ifwanFlowControl INTEGER
  ifwanMgmtInterface INTEGER
  ifwanEnquiryTimer-s INTEGER
  ifwanCllm INTEGER
  ifwanDsOSpeed-bps INTEGER
  ifwanFraming INTEGER
  ifwanTerminating INTEGER
  ifwanCrc4 INTEGER
  ifwanLineCoding INTEGER
  ifwanBChannels INTEGER
  ifwanMultiframing INTEGER
  ifwanMaxChannels INTEGER
  ifwanCondLMIPort INTEGER

IfwanFrUserEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanMgmtInterface INTEGER
  ifwanFlowControl INTEGER
  ifwanEnquiryTimer-s INTEGER
  ifwanReportCycle INTEGER
  ifwanCllm INTEGER
  ifwanDsOSpeed-bps INTEGER
  ifwanFraming INTEGER
  ifwanTerminating INTEGER
  ifwanCrc4 INTEGER
  ifwanLineCoding INTEGER
  ifwanBChannels INTEGER
  ifwanMultiframing INTEGER
  ifwanMaxChannels INTEGER
  ifwanSvcAddressType INTEGER
  ifwanSvcNetworkAddress DisplayString
  ifwanSvcMaxTxTimeoutT200 INTEGER
  ifwanSvcInactiveTimeoutT203 INTEGER
  ifwanSvcIframeRetransmissionsN200 INTEGER
  ifwanSvcSetupTimeoutT303 INTEGER
  ifwanSvcDisconnectTimeoutT305 INTEGER
  ifwanSvcReleaseTimeoutT308 INTEGER
  ifwanSvcCallProceedingTimeoutT310 INTEGER
  ifwanSvcStatusTimeoutT322 INTEGER

IfwanX25Entry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSpeed-bps INTEGER
  ifwanFallBackSpeed-bps INTEGER
  ifwanFallBackSpeedEnable INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanX25Encapsulation INTEGER
  ifwanPvcNumber INTEGER

IfwanSFEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanSfType INTEGER
  ifwanSpeed-bps INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanFlowControl INTEGER
  ifwanCllm INTEGER
  ifwanCellPacketization INTEGER
  ifwanMaxChannels INTEGER
  ifwanSfMode INTEGER
  ifwanSfCarrierId INTEGER

IfwanPppEntry  
SEQUENCE    
  ifwanIndex INTEGER
  ifwanDesc DisplayString
  ifwanProtocol INTEGER
  ifwanFormat INTEGER
  ifwanSpeed-bps INTEGER
  ifwanInterface INTEGER
  ifwanClocking INTEGER
  ifwanCoding INTEGER
  ifwanModem INTEGER
  ifwanTxStart INTEGER
  ifwanIdle INTEGER
  ifwanFrameDelay INTEGER
  ifwanRxFlow INTEGER
  ifwanTxFlow INTEGER
  ifwanTxHold-s INTEGER
  ifwanIpAddress IpAddress
  ifwanSubnetMask IpAddress
  ifwanIpRip INTEGER
  ifwanIpRipTxRx INTEGER
  ifwanIpRipAuthType INTEGER
  ifwanIpRipPassword DisplayString
  ifwanPppSilent INTEGER
  ifwanPppConfigRestartTimer INTEGER
  ifwanPppConfigRetries INTEGER
  ifwanPppNegociateLocalMru INTEGER
  ifwanPppLocalMru INTEGER
  ifwanPppNegociatePeerMru INTEGER
  ifwanPppPeerMruUpTo INTEGER
  ifwanPppNegociateAccm INTEGER
  ifwanPppRequestedAccmChar STRING Size(4)
  ifwanPppAcceptAccmPeer INTEGER
  ifwanPppAcceptableAccmChar STRING Size(4)
  ifwanPppRequestMagicNum INTEGER
  ifwanPppAcceptMagicNum INTEGER
  ifwanPppAcceptOldIpAddNeg INTEGER
  ifwanPppNegociateIpAddress INTEGER
  ifwanPppAcceptIpAddress INTEGER
  ifwanPppRemoteIpAddress IpAddress
  ifwanPppRemoteSubnetMask IpAddress

IfvceEntry  
SEQUENCE    
  ifvceIndex INTEGER
  ifvceDesc DisplayString
  ifvceProtocol INTEGER
  ifvceInterface INTEGER
  ifvceRemotePort INTEGER
  ifvceActivationType INTEGER
  ifvceRemoteUnit DisplayString
  ifvceHuntGroup INTEGER
  ifvcePulseMakeBreak-ms INTEGER
  ifvceToneDetectRegen-s INTEGER
  ifvceToneOn-ms INTEGER
  ifvceToneOff-ms INTEGER
  ifvceSilenceSuppress INTEGER
  ifvceToneEnergyDetec INTEGER
  ifvceDVCSilenceSuppress INTEGER
  ifvceSignaling INTEGER
  ifvceDTalkThreshold INTEGER
  ifvceLocalInbound INTEGER
  ifvceDVCLocalInbound INTEGER
  ifvceLocalOutbound INTEGER
  ifvceDVCLocalOutbound INTEGER
  ifvceFaxModemRelay INTEGER
  ifvceMaxFaxModemRate INTEGER
  ifvceFxoTimeout-s INTEGER
  ifvceTeTimer-s INTEGER
  ifvceFwdDigits INTEGER
  ifvceFwdType INTEGER
  ifvceFwdDelay-ms INTEGER
  ifvceDelDigits INTEGER
  ifvceExtNumber DisplayString
  ifvceLinkDwnBusy INTEGER
  ifvceToneType INTEGER
  ifvceRate8kx1 INTEGER
  ifvceRate8kx2 INTEGER
  ifvceRate8kx3 INTEGER
  ifvceRate6kx1 INTEGER
  ifvceRate6kx2 INTEGER
  ifvceRate6kx3 INTEGER
  ifvceRate5k8x1 INTEGER
  ifvceRate5k8x2 INTEGER
  ifvceRate4k8x1 INTEGER
  ifvceRate4k8x2 INTEGER
  ifvceBroadcastDir INTEGER
  ifvceBroadcastPvc INTEGER
  ifvceAnalogLinkDwnBusy INTEGER
  ifvceSpeedDialNum DisplayString
  ifvceExtendedDigitSrc INTEGER
  ifvceR2ExtendedDigitSrc INTEGER
  ifvceR2Group2Digit INTEGER
  ifvceR2CompleteDigit INTEGER
  ifvceR2BusyDigit INTEGER
  ifvceDtmfOnTime INTEGER
  ifvceEnableDtmfOnTime INTEGER

IfvceDVCEntry  
SEQUENCE    
  ifvceIndex INTEGER
  ifvceDesc DisplayString
  ifvceProtocol INTEGER
  ifvceInterface INTEGER
  ifvceRemotePort INTEGER
  ifvceActivationType INTEGER
  ifvceRemoteUnit DisplayString
  ifvceHuntGroup INTEGER
  ifvcePulseMakeBreak-ms INTEGER
  ifvceToneDetectRegen-s INTEGER
  ifvceToneOn-ms INTEGER
  ifvceToneOff-ms INTEGER
  ifvceToneEnergyDetec INTEGER
  ifvceDVCSilenceSuppress INTEGER
  ifvceSignaling INTEGER
  ifvceDTalkThreshold INTEGER
  ifvceDVCLocalInbound INTEGER
  ifvceDVCLocalOutbound INTEGER
  ifvceFaxModemRelay INTEGER
  ifvceMaxFaxModemRate INTEGER
  ifvceFwdDigits INTEGER
  ifvceFwdType INTEGER
  ifvceFwdDelay-ms INTEGER
  ifvceDelDigits INTEGER
  ifvceExtNumber DisplayString
  ifvceLinkDwnBusy INTEGER
  ifvceToneType INTEGER
  ifvceRate8kx1 INTEGER
  ifvceRate8kx2 INTEGER
  ifvceRate8kx3 INTEGER
  ifvceRate6kx1 INTEGER
  ifvceRate6kx2 INTEGER
  ifvceRate6kx3 INTEGER
  ifvceRate5k8x1 INTEGER
  ifvceRate5k8x2 INTEGER
  ifvceRate4k8x1 INTEGER
  ifvceRate4k8x2 INTEGER
  ifvceSpeedDialNum DisplayString
  ifvceExtendedDigitSrc INTEGER
  ifvceR2ExtendedDigitSrc INTEGER
  ifvceR2Group2Digit INTEGER
  ifvceR2CompleteDigit INTEGER
  ifvceR2BusyDigit INTEGER

IflanEntry  
SEQUENCE    
  iflanIndex INTEGER
  iflanDesc DisplayString
  iflanProtocol INTEGER
  iflanSpeed INTEGER
  iflanPriority INTEGER
  iflanCost INTEGER
  iflanPhysAddr STRING Size(6)
  iflanIpAddress IpAddress
  iflanSubnetMask IpAddress
  iflanMaxFrame INTEGER
  iflanIpRip INTEGER
  iflanIpRipTxRx INTEGER
  iflanIpRipAuthType INTEGER
  iflanIpRipPassword DisplayString
  iflanOspfEnable INTEGER
  iflanOspfAreaId IpAddress
  iflanOspfPriority INTEGER
  iflanOspfTransitDelay INTEGER
  iflanOspfRetransmitInt INTEGER
  iflanOspfHelloInt INTEGER
  iflanOspfDeadInt INTEGER
  iflanOspfPassword DisplayString
  iflanOspfMetricCost INTEGER
  iflanEth-LinkIntegrity INTEGER
  iflanTr-Monitor INTEGER
  iflanTr-Etr INTEGER
  iflanTr-RingNumber STRING Size(2)
  iflanIpxRip INTEGER
  iflanIpxSap INTEGER
  iflanIpxNetNum STRING Size(4)
  iflanIpxLanType INTEGER

IflanEthEntry  
SEQUENCE    
  iflanIndex INTEGER
  iflanDesc DisplayString
  iflanProtocol INTEGER
  iflanSpeed INTEGER
  iflanPriority INTEGER
  iflanCost INTEGER
  iflanPhysAddr STRING Size(6)
  iflanIpAddress IpAddress
  iflanSubnetMask IpAddress
  iflanMaxFrame INTEGER
  iflanIpRip INTEGER
  iflanIpRipTxRx INTEGER
  iflanIpRipAuthType INTEGER
  iflanIpRipPassword DisplayString
  iflanOspfEnable INTEGER
  iflanOspfAreaId IpAddress
  iflanOspfPriority INTEGER
  iflanOspfTransitDelay INTEGER
  iflanOspfRetransmitInt INTEGER
  iflanOspfHelloInt INTEGER
  iflanOspfDeadInt INTEGER
  iflanOspfPassword DisplayString
  iflanOspfMetricCost INTEGER
  iflanEth-LinkIntegrity INTEGER
  iflanIpxRip INTEGER
  iflanIpxSap INTEGER
  iflanIpxNetNum STRING Size(4)
  iflanIpxLanType INTEGER

IflanTrEntry  
SEQUENCE    
  iflanIndex INTEGER
  iflanDesc DisplayString
  iflanProtocol INTEGER
  iflanSpeed INTEGER
  iflanPriority INTEGER
  iflanCost INTEGER
  iflanPhysAddr STRING Size(6)
  iflanIpAddress IpAddress
  iflanSubnetMask IpAddress
  iflanMaxFrame INTEGER
  iflanIpRip INTEGER
  iflanIpRipTxRx INTEGER
  iflanIpRipAuthType INTEGER
  iflanIpRipPassword DisplayString
  iflanOspfEnable INTEGER
  iflanOspfAreaId IpAddress
  iflanOspfPriority INTEGER
  iflanOspfTransitDelay INTEGER
  iflanOspfRetransmitInt INTEGER
  iflanOspfHelloInt INTEGER
  iflanOspfDeadInt INTEGER
  iflanOspfPassword DisplayString
  iflanOspfMetricCost INTEGER
  iflanTr-Monitor INTEGER
  iflanTr-Etr INTEGER
  iflanTr-RingNumber STRING Size(2)
  iflanIpxRip INTEGER
  iflanIpxSap INTEGER
  iflanIpxNetNum STRING Size(4)
  iflanIpxLanType INTEGER

PuEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puRole INTEGER
  puSdlcPort INTEGER
  puSdlcAddress STRING Size(1)
  puSdlcPort2 INTEGER
  puSdlcAddress2 STRING Size(1)
  puSdlcTimeout-ms INTEGER
  puSdlcRetry INTEGER
  puSdlcWindow INTEGER
  puSdlcMaxFrame INTEGER
  puLlcDa STRING Size(6)
  puLlcTr-Routing INTEGER
  puLlcSsap STRING Size(1)
  puLlcDsap STRING Size(1)
  puLlcTimeout-ms INTEGER
  puLlcRetry INTEGER
  puLlcWindow INTEGER
  puLlcDynamicWindow INTEGER
  puLlcMaxFrame INTEGER
  puDlsDa STRING Size(6)
  puDlsSsap STRING Size(1)
  puDlsDsap STRING Size(1)
  puDlsIpSrc IpAddress
  puDlsIpDst IpAddress
  puDlsMaxFrame INTEGER
  puLinkRemoteUnit DisplayString
  puLinkClassNumber INTEGER
  puLinkRemPu INTEGER
  puBnnPvc INTEGER
  puBnnFid INTEGER
  puBanDa STRING Size(6)
  puBanBnnSsap STRING Size(1)
  puBanBnnDsap STRING Size(1)
  puBanBnnTimeout-ms INTEGER
  puBanBnnRetry INTEGER
  puBanBnnWindow INTEGER
  puBanBnnNw INTEGER
  puBanBnnMaxFrame INTEGER
  puBanRouting INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

PuSdlcLlcEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puSdlcPort INTEGER
  puSdlcAddress STRING Size(1)
  puSdlcTimeout-ms INTEGER
  puSdlcRetry INTEGER
  puSdlcWindow INTEGER
  puSdlcMaxFrame INTEGER
  puLlcDa STRING Size(6)
  puLlcTr-Routing INTEGER
  puLlcSsap STRING Size(1)
  puLlcDsap STRING Size(1)
  puLlcTimeout-ms INTEGER
  puLlcRetry INTEGER
  puLlcWindow INTEGER
  puLlcDynamicWindow INTEGER
  puLlcMaxFrame INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

PuSdlcSdlcEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puSdlcPort INTEGER
  puSdlcAddress STRING Size(1)
  puSdlcPort2 INTEGER
  puSdlcAddress2 STRING Size(1)
  puSdlcTimeout-ms INTEGER
  puSdlcRetry INTEGER
  puSdlcWindow INTEGER
  puXid INTEGER

PuSdlcDlswEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puSdlcPort INTEGER
  puSdlcAddress STRING Size(1)
  puSdlcTimeout-ms INTEGER
  puSdlcRetry INTEGER
  puSdlcWindow INTEGER
  puSdlcMaxFrame INTEGER
  puDlsDa STRING Size(6)
  puDlsSsap STRING Size(1)
  puDlsDsap STRING Size(1)
  puDlsIpSrc IpAddress
  puDlsIpDst IpAddress
  puDlsMaxFrame INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

PuSdlcLinksEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puSdlcPort INTEGER
  puSdlcAddress STRING Size(1)
  puSdlcTimeout-ms INTEGER
  puSdlcRetry INTEGER
  puSdlcWindow INTEGER
  puSdlcMaxFrame INTEGER
  puLinkRemoteUnit DisplayString
  puLinkClassNumber INTEGER
  puLinkRemPu INTEGER
  puXid INTEGER

PuLlcDlswEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puRole INTEGER
  puLlcDa STRING Size(6)
  puLlcTr-Routing INTEGER
  puLlcSsap STRING Size(1)
  puLlcDsap STRING Size(1)
  puLlcTimeout-ms INTEGER
  puLlcRetry INTEGER
  puLlcWindow INTEGER
  puLlcDynamicWindow INTEGER
  puLlcMaxFrame INTEGER
  puDlsDa STRING Size(6)
  puDlsSsap STRING Size(1)
  puDlsDsap STRING Size(1)
  puDlsIpSrc IpAddress
  puDlsIpDst IpAddress
  puDlsMaxFrame INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

PuLlcLinksEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puRole INTEGER
  puLlcDa STRING Size(6)
  puLlcTr-Routing INTEGER
  puLlcSsap STRING Size(1)
  puLlcDsap STRING Size(1)
  puLlcTimeout-ms INTEGER
  puLlcRetry INTEGER
  puLlcWindow INTEGER
  puLlcDynamicWindow INTEGER
  puLlcMaxFrame INTEGER
  puLinkRemoteUnit DisplayString
  puLinkClassNumber INTEGER
  puLinkRemPu INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

PuDlswLinksEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puRole INTEGER
  puDlsDa STRING Size(6)
  puDlsSsap STRING Size(1)
  puDlsDsap STRING Size(1)
  puDlsIpSrc IpAddress
  puDlsIpDst IpAddress
  puDlsMaxFrame INTEGER
  puLinkRemoteUnit DisplayString
  puLinkClassNumber INTEGER
  puLinkRemPu INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

PuSdlcBanEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puSdlcPort INTEGER
  puSdlcAddress STRING Size(1)
  puSdlcTimeout-ms INTEGER
  puSdlcRetry INTEGER
  puSdlcWindow INTEGER
  puSdlcMaxFrame INTEGER
  puBanDa STRING Size(6)
  puBanBnnSsap STRING Size(1)
  puBanBnnDsap STRING Size(1)
  puBanBnnTimeout-ms INTEGER
  puBanBnnRetry INTEGER
  puBanBnnWindow INTEGER
  puBanBnnNw INTEGER
  puBanBnnMaxFrame INTEGER
  puBanRouting INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

PuSdlcBnnEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puSdlcPort INTEGER
  puSdlcAddress STRING Size(1)
  puSdlcTimeout-ms INTEGER
  puSdlcRetry INTEGER
  puSdlcWindow INTEGER
  puSdlcMaxFrame INTEGER
  puBnnPvc INTEGER
  puBnnFid INTEGER
  puBanBnnSsap STRING Size(1)
  puBanBnnDsap STRING Size(1)
  puBanBnnTimeout-ms INTEGER
  puBanBnnRetry INTEGER
  puBanBnnWindow INTEGER
  puBanBnnNw INTEGER
  puBanBnnMaxFrame INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

PuLlcBanEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puRole INTEGER
  puLlcDa STRING Size(6)
  puLlcSsap STRING Size(1)
  puLlcDsap STRING Size(1)
  puLlcTimeout-ms INTEGER
  puLlcRetry INTEGER
  puLlcWindow INTEGER
  puLlcDynamicWindow INTEGER
  puLlcMaxFrame INTEGER
  puBanDa STRING Size(6)
  puBanBnnSsap STRING Size(1)
  puBanBnnDsap STRING Size(1)
  puBanBnnTimeout-ms INTEGER
  puBanBnnRetry INTEGER
  puBanBnnWindow INTEGER
  puBanBnnNw INTEGER
  puBanBnnMaxFrame INTEGER
  puBanRouting INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

PuLlcBnnEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puRole INTEGER
  puLlcDa STRING Size(6)
  puLlcSsap STRING Size(1)
  puLlcDsap STRING Size(1)
  puLlcTimeout-ms INTEGER
  puLlcRetry INTEGER
  puLlcWindow INTEGER
  puLlcDynamicWindow INTEGER
  puLlcMaxFrame INTEGER
  puBnnPvc INTEGER
  puBnnFid INTEGER
  puBanBnnSsap STRING Size(1)
  puBanBnnDsap STRING Size(1)
  puBanBnnTimeout-ms INTEGER
  puBanBnnRetry INTEGER
  puBanBnnWindow INTEGER
  puBanBnnNw INTEGER
  puBanBnnMaxFrame INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

PuDlsBanEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puRole INTEGER
  puDlsDa STRING Size(6)
  puDlsSsap STRING Size(1)
  puDlsDsap STRING Size(1)
  puDlsIpSrc IpAddress
  puDlsIpDst IpAddress
  puDlsMaxFrame INTEGER
  puBanDa STRING Size(6)
  puBanBnnSsap STRING Size(1)
  puBanBnnDsap STRING Size(1)
  puBanBnnTimeout-ms INTEGER
  puBanBnnRetry INTEGER
  puBanBnnWindow INTEGER
  puBanBnnNw INTEGER
  puBanBnnMaxFrame INTEGER
  puBanRouting INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

PuDlsBnnEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puRole INTEGER
  puDlsDa STRING Size(6)
  puDlsSsap STRING Size(1)
  puDlsDsap STRING Size(1)
  puDlsIpSrc IpAddress
  puDlsIpDst IpAddress
  puDlsMaxFrame INTEGER
  puBnnPvc INTEGER
  puBnnFid INTEGER
  puBanBnnSsap STRING Size(1)
  puBanBnnDsap STRING Size(1)
  puBanBnnTimeout-ms INTEGER
  puBanBnnRetry INTEGER
  puBanBnnWindow INTEGER
  puBanBnnNw INTEGER
  puBanBnnMaxFrame INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

PuBanLinkEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puRole INTEGER
  puBanDa STRING Size(6)
  puBanBnnSsap STRING Size(1)
  puBanBnnDsap STRING Size(1)
  puBanBnnTimeout-ms INTEGER
  puBanBnnRetry INTEGER
  puBanBnnWindow INTEGER
  puBanBnnNw INTEGER
  puBanBnnMaxFrame INTEGER
  puBanRouting INTEGER
  puLinkRemoteUnit DisplayString
  puLinkClassNumber INTEGER
  puLinkRemPu INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

PuBnnLinkEntry  
SEQUENCE    
  puIndex INTEGER
  puMode INTEGER
  puActive INTEGER
  puDelayBeforeConn-s INTEGER
  puRole INTEGER
  puBnnPvc INTEGER
  puBnnFid INTEGER
  puBanBnnSsap STRING Size(1)
  puBanBnnDsap STRING Size(1)
  puBanBnnTimeout-ms INTEGER
  puBanBnnRetry INTEGER
  puBanBnnWindow INTEGER
  puBanBnnNw INTEGER
  puBanBnnMaxFrame INTEGER
  puLinkRemoteUnit DisplayString
  puLinkClassNumber INTEGER
  puLinkRemPu INTEGER
  puXid INTEGER
  puXidId STRING Size(4)
  puXidFormat INTEGER
  puXidPuType INTEGER

ScheduleEntry  
SEQUENCE    
  schedulePeriod INTEGER
  scheduleEnable INTEGER
  scheduleDay INTEGER
  scheduleBeginTime DisplayString
  scheduleEndTime DisplayString
  schedulePort1 INTEGER
  schedulePort2 INTEGER
  schedulePort3 INTEGER
  schedulePort4 INTEGER
  schedulePort5 INTEGER
  schedulePort6 INTEGER
  schedulePort7 INTEGER
  schedulePort8 INTEGER

PhoneEntry  
SEQUENCE    
  phoneIndex INTEGER
  phoneRemoteUnit DisplayString
  phonePhoneNumber DisplayString
  phoneNextHop DisplayString
  phoneCost INTEGER

FilterEntry  
SEQUENCE    
  filterIndex INTEGER
  filterActive INTEGER
  filterDefinition DisplayString

ClassEntry  
SEQUENCE    
  classIndex INTEGER
  classWeight INTEGER
  classPrefRoute DisplayString

PvcEntry  
SEQUENCE    
  pvcIndex INTEGER
  pvcMode INTEGER
  pvcDlciAddress INTEGER
  pvcPort INTEGER
  pvcUserPort INTEGER
  pvcInfoRate INTEGER
  pvcBurstInfoRate INTEGER
  pvcType INTEGER
  pvcBackupCall-s INTEGER
  pvcBackupHang-s INTEGER
  pvcDialTimeout INTEGER
  pvcBackup INTEGER
  pvcPriority INTEGER
  pvcCost INTEGER
  pvcRemoteUnit DisplayString
  pvcTimeout-ms INTEGER
  pvcRetry INTEGER
  pvcCompression INTEGER
  pvcIpAddress IpAddress
  pvcSubnetMask IpAddress
  pvcMaxFrame INTEGER
  pvcBroadcastGroup INTEGER
  pvcIpRip INTEGER
  pvcIpRipTxRx INTEGER
  pvcIpRipAuthType INTEGER
  pvcIpRipPassword DisplayString
  pvcOspfEnable INTEGER
  pvcOspfAreaId IpAddress
  pvcOspfTransitDelay INTEGER
  pvcOspfRetransmitInt INTEGER
  pvcOspfHelloInt INTEGER
  pvcOspfDeadInt INTEGER
  pvcOspfPassword DisplayString
  pvcOspfMetricCost INTEGER
  pvcBrgConnection INTEGER
  pvcIpConnection INTEGER
  pvcIpxConnection INTEGER
  pvcLlcConnection INTEGER
  pvcRemotePvc INTEGER
  pvcPvcClass INTEGER
  pvcUserDlci INTEGER
  pvcNetworkDlci INTEGER
  pvcNetworkPort INTEGER
  pvcRingNumber STRING Size(2)
  pvcIpxRip INTEGER
  pvcIpxSap INTEGER
  pvcIpxNetNum STRING Size(4)
  pvcProxyAddr INTEGER 1..8
  pvcMaxChannels INTEGER
  pvcHuntForwardingAUnit DisplayString
  pvcHuntForwardingBUnit DisplayString
  pvcRemoteFpUnit DisplayString

PvcPvcrEntry  
SEQUENCE    
  pvcIndex INTEGER
  pvcMode INTEGER
  pvcDlciAddress INTEGER
  pvcPort INTEGER
  pvcInfoRate INTEGER
  pvcBurstInfoRate INTEGER
  pvcType INTEGER
  pvcBackupCall-s INTEGER
  pvcBackupHang-s INTEGER
  pvcDialTimeout INTEGER
  pvcBackup INTEGER
  pvcPriority INTEGER
  pvcCost INTEGER
  pvcRemoteUnit DisplayString
  pvcTimeout-ms INTEGER
  pvcRetry INTEGER
  pvcCompression INTEGER
  pvcIpAddress IpAddress
  pvcSubnetMask IpAddress
  pvcMaxFrame INTEGER
  pvcBroadcastGroup INTEGER
  pvcIpRip INTEGER
  pvcIpRipTxRx INTEGER
  pvcIpRipAuthType INTEGER
  pvcIpRipPassword DisplayString
  pvcOspfEnable INTEGER
  pvcOspfAreaId IpAddress
  pvcOspfTransitDelay INTEGER
  pvcOspfRetransmitInt INTEGER
  pvcOspfHelloInt INTEGER
  pvcOspfDeadInt INTEGER
  pvcOspfPassword DisplayString
  pvcOspfMetricCost INTEGER
  pvcRingNumber STRING Size(2)
  pvcIpxRip INTEGER
  pvcIpxSap INTEGER
  pvcIpxNetNum STRING Size(4)
  pvcLlcConnection INTEGER
  pvcMaxChannels INTEGER

PvcRfc1490Entry  
SEQUENCE    
  pvcIndex INTEGER
  pvcMode INTEGER
  pvcDlciAddress INTEGER
  pvcPort INTEGER
  pvcInfoRate INTEGER
  pvcBurstInfoRate INTEGER
  pvcPriority INTEGER
  pvcCost INTEGER
  pvcRemoteUnit DisplayString
  pvcIpAddress IpAddress
  pvcSubnetMask IpAddress
  pvcMaxFrame INTEGER
  pvcIpRip INTEGER
  pvcIpRipTxRx INTEGER
  pvcIpRipAuthType INTEGER
  pvcIpRipPassword DisplayString
  pvcOspfEnable INTEGER
  pvcOspfAreaId IpAddress
  pvcOspfTransitDelay INTEGER
  pvcOspfRetransmitInt INTEGER
  pvcOspfHelloInt INTEGER
  pvcOspfDeadInt INTEGER
  pvcOspfPassword DisplayString
  pvcOspfMetricCost INTEGER
  pvcBrgConnection INTEGER
  pvcIpConnection INTEGER
  pvcIpxConnection INTEGER
  pvcLlcConnection INTEGER
  pvcRingNumber STRING Size(2)
  pvcIpxRip INTEGER
  pvcIpxSap INTEGER
  pvcIpxNetNum STRING Size(4)
  pvcProxyAddr INTEGER

PvcMultiplexEntry  
SEQUENCE    
  pvcIndex INTEGER
  pvcMode INTEGER
  pvcDlciAddress INTEGER
  pvcPort INTEGER
  pvcInfoRate INTEGER
  pvcBurstInfoRate INTEGER
  pvcRemoteUnit DisplayString
  pvcRemotePvc INTEGER
  pvcPvcClass INTEGER
  pvcCompression INTEGER

PvcTranspEntry  
SEQUENCE    
  pvcIndex INTEGER
  pvcMode INTEGER
  pvcDlciAddress INTEGER
  pvcUserDlci INTEGER
  pvcUserPort INTEGER
  pvcInfoRate INTEGER
  pvcBurstInfoRate INTEGER
  pvcNetworkDlci INTEGER
  pvcNetworkPort INTEGER

PvcFPEntry  
SEQUENCE    
  pvcIndex INTEGER
  pvcMode INTEGER
  pvcDlciAddress INTEGER
  pvcPort INTEGER
  pvcInfoRate INTEGER
  pvcBurstInfoRate INTEGER
  pvcRemoteUnit DisplayString
  pvcIpAddress IpAddress
  pvcSubnetMask IpAddress
  pvcMaxFrame INTEGER
  pvcProxyAddr INTEGER 1..8
  pvcMaxChannels INTEGER
  pvcHuntForwardingAUnit DisplayString
  pvcHuntForwardingBUnit DisplayString

PvcFpMultiplexEntry  
SEQUENCE    
  pvcIndex INTEGER
  pvcMode INTEGER
  pvcRemoteUnit DisplayString
  pvcRemotePvc INTEGER
  pvcPvcClass INTEGER
  pvcCompression INTEGER
  pvcIpAddress IpAddress
  pvcSubnetMask IpAddress
  pvcMaxFrame INTEGER
  pvcProxyAddr INTEGER 1..8
  pvcMaxChannels INTEGER
  pvcHuntForwardingAUnit DisplayString
  pvcHuntForwardingBUnit DisplayString
  pvcRemoteFpUnit DisplayString

IpstaticEntry  
SEQUENCE    
  ipstaticIndex INTEGER
  ipstaticValid INTEGER
  ipstaticIpDest IpAddress
  ipstaticMask IpAddress
  ipstaticNextHop IpAddress

OspfAreaEntry  
SEQUENCE    
  ospfAreaIndex INTEGER
  ospfAreaAreaId IpAddress
  ospfAreaEnable INTEGER
  ospfAreaAuthType INTEGER
  ospfAreaImportASExt INTEGER
  ospfAreaStubMetric INTEGER

OspfRangeEntry  
SEQUENCE    
  ospfRangeIndex INTEGER
  ospfRangeNet IpAddress
  ospfRangeMask IpAddress
  ospfRangeEnable INTEGER
  ospfRangeStatus INTEGER
  ospfRangeAddToArea IpAddress

OspfVLinkEntry  
SEQUENCE    
  ospfVLinkIndex INTEGER
  ospfVLinkTransitAreaId IpAddress
  ospfVLinkNeighborRtrId IpAddress
  ospfVLinkEnable INTEGER
  ospfVLinkTransitDelay INTEGER
  ospfVLinkRetransmitInt INTEGER
  ospfVLinkHelloInt INTEGER
  ospfVLinkDeadInt INTEGER
  ospfVLinkPassword DisplayString

IpxfilterEntry  
SEQUENCE    
  ipxfilterIndex INTEGER
  ipxfilterEnable INTEGER
  ipxfilterSap STRING Size(2)
  ipxfilterType INTEGER

StatAlarmEntry  
SEQUENCE    
  statAlarmIndex INTEGER
  statAlarmDesc DisplayString
  statAlarmDate DisplayString
  statAlarmTime DisplayString
  statAlarmModule INTEGER
  statAlarmAlarm INTEGER
  statAlarmArg INTEGER

StatIfwanEntry  
SEQUENCE    
  statIfwanIndex INTEGER
  statIfwanDesc DisplayString
  statIfwanProtocol INTEGER
  statIfwanInterface DisplayString
  statIfwanModemSignal DisplayString
  statIfwanSpeed INTEGER
  statIfwanState DisplayString
  statIfwanDropInsert DisplayString
  statIfwanTrspState DisplayString
  statIfwanTrspLastError DisplayString
  statIfwanMeanTx Gauge
  statIfwanMeanRx Gauge
  statIfwanPeakTx Gauge
  statIfwanPeakRx Gauge
  statIfwanBadFrames Counter
  statIfwanBadFlags DisplayString
  statIfwanUnderruns Counter
  statIfwanRetries Counter
  statIfwanRestart Counter
  statIfwanFramesTx Counter
  statIfwanFramesRx Counter
  statIfwanOctetsTx Counter
  statIfwanOctetsRx Counter
  statIfwanOvrFrames Counter
  statIfwanBadOctets Counter
  statIfwanOvrOctets Counter
  statIfwanCompErrs Counter
  statIfwanChOverflows Counter
  statIfwanChAborts Counter
  statIfwanChSeqErrs Counter
  statIfwanT1E1ESS Counter
  statIfwanT1E1SES Counter
  statIfwanT1E1SEF Counter
  statIfwanT1E1UAS Counter
  statIfwanT1E1CSS Counter
  statIfwanT1E1PCV Counter
  statIfwanT1E1LES Counter
  statIfwanT1E1BES Counter
  statIfwanT1E1DM Counter
  statIfwanT1E1LCV Counter
  statIfwanQ922State DisplayString

StatIfwanStates  
SEQUENCE    
  statIfwanIndex INTEGER
  statIfwanDesc DisplayString
  statIfwanProtocol INTEGER
  statIfwanInterface DisplayString
  statIfwanModemSignal DisplayString
  statIfwanSpeed INTEGER
  statIfwanState DisplayString
  statIfwanDropInsert DisplayString
  statIfwanTrspState DisplayString
  statIfwanTrspLastError DisplayString
  statIfwanQ922State DisplayString

StatIfwanCounters  
SEQUENCE    
  statIfwanIndex INTEGER
  statIfwanDesc DisplayString
  statIfwanProtocol INTEGER
  statIfwanMeanTx Gauge
  statIfwanMeanRx Gauge
  statIfwanPeakTx Gauge
  statIfwanPeakRx Gauge
  statIfwanFramesTx Counter
  statIfwanFramesRx Counter
  statIfwanOctetsTx Counter
  statIfwanOctetsRx Counter

StatIfwanErrors  
SEQUENCE    
  statIfwanIndex INTEGER
  statIfwanDesc DisplayString
  statIfwanProtocol INTEGER
  statIfwanBadFrames Counter
  statIfwanBadFlags DisplayString
  statIfwanUnderruns Counter
  statIfwanRetries Counter
  statIfwanRestart Counter
  statIfwanOvrFrames Counter
  statIfwanBadOctets Counter
  statIfwanOvrOctets Counter
  statIfwanCompErrs Counter
  statIfwanChOverflows Counter
  statIfwanChAborts Counter
  statIfwanChSeqErrs Counter
  statIfwanT1E1ESS Counter
  statIfwanT1E1SES Counter
  statIfwanT1E1SEF Counter
  statIfwanT1E1UAS Counter
  statIfwanT1E1CSS Counter
  statIfwanT1E1PCV Counter
  statIfwanT1E1LES Counter
  statIfwanT1E1BES Counter
  statIfwanT1E1DM Counter
  statIfwanT1E1LCV Counter

StatIflanEntry  
SEQUENCE    
  statIflanIndex INTEGER
  statIflanProtocol INTEGER
  statIflanSpeed INTEGER
  statIflanConnectionStatus DisplayString
  statIflanOperatingMode DisplayString
  statIflanEth-Interface DisplayString
  statIflanMeanTx-kbps Gauge
  statIflanMeanRx-kbps Gauge
  statIflanPeakTx-kbps Gauge
  statIflanPeakRx-kbps Gauge
  statIflanRetries Counter
  statIflanBadFrames Counter
  statIflanBadFlags DisplayString
  statIflanTr-ReceiveCongestion Counter
  statIflanEth-OneCollision Counter
  statIflanEth-TwoCollisions Counter
  statIflanEth-ThreeAndMoreCol Counter
  statIflanEth-DeferredTrans Counter
  statIflanEth-ExcessiveCollision Counter
  statIflanEth-LateCollision Counter
  statIflanEth-FrameCheckSeq Counter
  statIflanEth-Align Counter
  statIflanEth-CarrierSense Counter

StatIflanEth  
SEQUENCE    
  statIflanIndex INTEGER
  statIflanProtocol INTEGER
  statIflanSpeed INTEGER
  statIflanConnectionStatus DisplayString
  statIflanOperatingMode DisplayString
  statIflanEth-Interface DisplayString
  statIflanMeanTx-kbps Gauge
  statIflanMeanRx-kbps Gauge
  statIflanPeakTx-kbps Gauge
  statIflanPeakRx-kbps Gauge
  statIflanRetries Counter
  statIflanBadFrames Counter
  statIflanBadFlags DisplayString
  statIflanEth-OneCollision Counter
  statIflanEth-TwoCollisions Counter
  statIflanEth-ThreeAndMoreCol Counter
  statIflanEth-DeferredTrans Counter
  statIflanEth-ExcessiveCollision Counter
  statIflanEth-LateCollision Counter
  statIflanEth-FrameCheckSeq Counter
  statIflanEth-Align Counter
  statIflanEth-CarrierSense Counter

StatIflanTr  
SEQUENCE    
  statIflanIndex INTEGER
  statIflanProtocol INTEGER
  statIflanSpeed INTEGER
  statIflanConnectionStatus DisplayString
  statIflanOperatingMode DisplayString
  statIflanMeanTx-kbps Gauge
  statIflanMeanRx-kbps Gauge
  statIflanPeakTx-kbps Gauge
  statIflanPeakRx-kbps Gauge
  statIflanRetries Counter
  statIflanBadFrames Counter
  statIflanBadFlags DisplayString
  statIflanTr-ReceiveCongestion Counter

StatIfvceEntry  
SEQUENCE    
  statIfvceIndex INTEGER
  statIfvceDesc DisplayString
  statIfvceState INTEGER
  statIfvceProtocol INTEGER
  statIfvceLastError INTEGER
  statIfvceFaxRate INTEGER
  statIfvceFaxMode INTEGER
  statIfvceOverruns Counter
  statIfvceUnderruns Counter
  statIfvceDvcPortInUse DisplayString

StatPuEntry  
SEQUENCE    
  statPuIndex INTEGER
  statPuMode INTEGER
  statPuConnectionStatus DisplayString
  statPuCompErrs Counter
  statPuChOverflows Counter
  statPuChAborts Counter
  statPuChSeqErrs Counter

StatBridgePortEntry  
SEQUENCE    
  statBridgePortIndex INTEGER
  statBridgePortDestination DisplayString
  statBridgePortState DisplayString
  statBridgePortDesignatedRoot DisplayString
  statBridgePortDesignatedCost DisplayString
  statBridgePortDesignatedBridge DisplayString
  statBridgePortDesignatedPort DisplayString
  statBridgePortTrspFrameIn DisplayString
  statBridgePortTrspFrameOut DisplayString
  statBridgePortTr-SpecRteFrameIn DisplayString
  statBridgePortTr-SpecRteFrameOut DisplayString
  statBridgePortTr-AllRteFrameIn DisplayString
  statBridgePortTr-AllRteFrameOut DisplayString
  statBridgePortTr-SingleRteFrameIn DisplayString
  statBridgePortTr-SingleRteFrameOut DisplayString
  statBridgePortTr-SegmentMismatch DisplayString
  statBridgePortTr-SegmentDuplicate DisplayString
  statBridgePortTr-HopCntExceeded DisplayString
  statBridgePortTr-FrmLngExceeded DisplayString

StatBridgePort-Ethlan  
SEQUENCE    
  statBridgePortIndex INTEGER
  statBridgePortDestination DisplayString
  statBridgePortState DisplayString
  statBridgePortDesignatedRoot DisplayString
  statBridgePortDesignatedCost DisplayString
  statBridgePortDesignatedBridge DisplayString
  statBridgePortDesignatedPort DisplayString
  statBridgePortTrspFrameIn DisplayString
  statBridgePortTrspFrameOut DisplayString

StatBridgePort-Trlan  
SEQUENCE    
  statBridgePortIndex INTEGER
  statBridgePortDestination DisplayString
  statBridgePortState DisplayString
  statBridgePortDesignatedRoot DisplayString
  statBridgePortDesignatedCost DisplayString
  statBridgePortDesignatedBridge DisplayString
  statBridgePortDesignatedPort DisplayString
  statBridgePortTrspFrameIn DisplayString
  statBridgePortTrspFrameOut DisplayString
  statBridgePortTr-SpecRteFrameIn DisplayString
  statBridgePortTr-SpecRteFrameOut DisplayString
  statBridgePortTr-AllRteFrameIn DisplayString
  statBridgePortTr-AllRteFrameOut DisplayString
  statBridgePortTr-SingleRteFrameIn DisplayString
  statBridgePortTr-SingleRteFrameOut DisplayString
  statBridgePortTr-SegmentMismatch DisplayString
  statBridgePortTr-SegmentDuplicate DisplayString
  statBridgePortTr-HopCntExceeded DisplayString
  statBridgePortTr-FrmLngExceeded DisplayString

StatPvcEntry  
SEQUENCE    
  statPvcIndex INTEGER
  statPvcProtocol DisplayString
  statPvcMode DisplayString
  statPvcInfoSignal DisplayString
  statPvcSpeed DisplayString
  statPvcState DisplayString
  statPvcDlci INTEGER
  statPvcMeanTx Gauge
  statPvcMeanRx Gauge
  statPvcPeakTx Gauge
  statPvcPeakRx Gauge
  statPvcError Counter
  statPvcRestart Counter
  statPvcFramesTx Counter
  statPvcFramesRx Counter
  statPvcOctetsTx Counter
  statPvcOctetsRx Counter
  statPvcBadFrames Counter
  statPvcOvrFrames Counter
  statPvcBadOctets Counter
  statPvcOvrOctets Counter
  statPvcCompErrs Counter
  statPvcChOverflows Counter
  statPvcChAborts Counter
  statPvcChSeqErrs Counter

StatPvcStates  
SEQUENCE    
  statPvcIndex INTEGER
  statPvcProtocol DisplayString
  statPvcMode DisplayString
  statPvcInfoSignal DisplayString
  statPvcSpeed DisplayString
  statPvcState DisplayString
  statPvcDlci INTEGER

StatPvcCounters  
SEQUENCE    
  statPvcIndex INTEGER
  statPvcProtocol DisplayString
  statPvcMeanTx Gauge
  statPvcMeanRx Gauge
  statPvcPeakTx Gauge
  statPvcPeakRx Gauge
  statPvcFramesTx Counter
  statPvcFramesRx Counter
  statPvcOctetsTx Counter
  statPvcOctetsRx Counter
  statPvcCompErrs Counter
  statPvcChOverflows Counter
  statPvcChAborts Counter
  statPvcChSeqErrs Counter

StatPvcErrors  
SEQUENCE    
  statPvcIndex INTEGER
  statPvcProtocol DisplayString
  statPvcError Counter
  statPvcRestart Counter
  statPvcBadFrames Counter
  statPvcOvrFrames Counter
  statPvcBadOctets Counter
  statPvcOvrOctets Counter

StatPvcrRouteEntry  
SEQUENCE    
  statPvcrRouteName DisplayString
  statPvcrRouteNextHop DisplayString
  statPvcrRouteValid INTEGER
  statPvcrRouteMetric Gauge
  statPvcrRouteIntrf INTEGER
  statPvcrRouteAge INTEGER

StatGrpEntry  
SEQUENCE    
  statGrpIndex INTEGER
  statGrpDestName DisplayString
  statGrpOutOfSeqErrs INTEGER
  statGrpSorterTimeouts INTEGER
  statGrpSorterOverruns INTEGER

StatSvcEntry  
SEQUENCE    
  statSvcIndex INTEGER
  statSvcProtocol DisplayString
  statSvcMode DisplayString
  statSvcInfoSignal DisplayString
  statSvcSpeed DisplayString
  statSvcState DisplayString
  statSvcDlci INTEGER
  statSvcMeanTx Gauge
  statSvcMeanRx Gauge
  statSvcPeakTx Gauge
  statSvcPeakRx Gauge
  statSvcError Counter
  statSvcRestart Counter
  statSvcFramesTx Counter
  statSvcFramesRx Counter
  statSvcOctetsTx Counter
  statSvcOctetsRx Counter
  statSvcBadFrames Counter
  statSvcOvrFrames Counter
  statSvcBadOctets Counter
  statSvcOvrOctets Counter

StatSvcStates  
SEQUENCE    
  statSvcIndex INTEGER
  statSvcProtocol DisplayString
  statSvcMode DisplayString
  statSvcInfoSignal DisplayString
  statSvcSpeed DisplayString
  statSvcState DisplayString
  statSvcDlci INTEGER

StatSvcCounters  
SEQUENCE    
  statSvcIndex INTEGER
  statSvcProtocol DisplayString
  statSvcMeanTx Gauge
  statSvcMeanRx Gauge
  statSvcPeakTx Gauge
  statSvcPeakRx Gauge
  statSvcFramesTx Counter
  statSvcFramesRx Counter
  statSvcOctetsTx Counter
  statSvcOctetsRx Counter

StatSvcErrors  
SEQUENCE    
  statSvcIndex INTEGER
  statSvcProtocol DisplayString
  statSvcError Counter
  statSvcRestart Counter
  statSvcBadFrames Counter
  statSvcOvrFrames Counter
  statSvcBadOctets Counter
  statSvcOvrOctets Counter

StatIfcemEntry  
SEQUENCE    
  statIfcemIndex INTEGER
  statIfcemDesc DisplayString
  statIfcemClockState DisplayString

Defined Values

lucent 1.3.6.1.4.1.727
OBJECT IDENTIFIER    

cleartrac7 1.3.6.1.4.1.727.7
OBJECT IDENTIFIER    

mgmt 1.3.6.1.4.1.727.7.2
OBJECT IDENTIFIER    

system 1.3.6.1.4.1.727.7.2.1
OBJECT IDENTIFIER    

ifwan 1.3.6.1.4.1.727.7.2.2
OBJECT IDENTIFIER    

iflan 1.3.6.1.4.1.727.7.2.3
OBJECT IDENTIFIER    

ifvce 1.3.6.1.4.1.727.7.2.18
OBJECT IDENTIFIER    

pu 1.3.6.1.4.1.727.7.2.4
OBJECT IDENTIFIER    

schedule 1.3.6.1.4.1.727.7.2.5
OBJECT IDENTIFIER    

bridge 1.3.6.1.4.1.727.7.2.6
OBJECT IDENTIFIER    

phone 1.3.6.1.4.1.727.7.2.7
OBJECT IDENTIFIER    

filter 1.3.6.1.4.1.727.7.2.8
OBJECT IDENTIFIER    

class 1.3.6.1.4.1.727.7.2.9
OBJECT IDENTIFIER    

pvc 1.3.6.1.4.1.727.7.2.10
OBJECT IDENTIFIER    

ipx 1.3.6.1.4.1.727.7.2.11
OBJECT IDENTIFIER    

ipstatic 1.3.6.1.4.1.727.7.2.13
OBJECT IDENTIFIER    

ip 1.3.6.1.4.1.727.7.2.14
OBJECT IDENTIFIER    

ospf 1.3.6.1.4.1.727.7.2.15
OBJECT IDENTIFIER    

ipxfilter 1.3.6.1.4.1.727.7.2.16
OBJECT IDENTIFIER    

stat 1.3.6.1.4.1.727.7.2.20
OBJECT IDENTIFIER    

intf 1.3.6.1.4.1.727.7.2.30
OBJECT IDENTIFIER    

slot 1.3.6.1.4.1.727.7.2.31
OBJECT IDENTIFIER    

ipaddr 1.3.6.1.4.1.727.7.2.32
OBJECT IDENTIFIER    

bootp 1.3.6.1.4.1.727.7.2.33
OBJECT IDENTIFIER    

proxy 1.3.6.1.4.1.727.7.2.34
OBJECT IDENTIFIER    

timep 1.3.6.1.4.1.727.7.2.35
OBJECT IDENTIFIER    

sysDesc 1.3.6.1.4.1.727.7.2.1.1
This variable contains a printable octet string which contains the full name and version of the product.
OBJECT-TYPE    
  DisplayString  

sysContact 1.3.6.1.4.1.727.7.2.1.2
The textual identification of the contact person for this managed node, together with information on how to contact this person.
OBJECT-TYPE    
  DisplayString Size(0..32)  

sysName 1.3.6.1.4.1.727.7.2.1.3
An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name.
OBJECT-TYPE    
  DisplayString Size(0..32)  

sysUnitRoutingVersion 1.3.6.1.4.1.727.7.2.1.21
Unit Routing Version: The routing version to be used on this unit. Select 1 if any cleartrac7 units in the network are running Unit Routing Version 1 (the version used in all software releases earlier than 6.7.0). Select 2 if all cleartrac7 units in the network are running Unit Routing Version 2 (software release 6.7.0).
OBJECT-TYPE    
  INTEGER 1..2  

sysLocation 1.3.6.1.4.1.727.7.2.1.4
The physical location of this node (e.g., `telephone closet, 3rd floor').
OBJECT-TYPE    
  DisplayString Size(0..32)  

sysDate 1.3.6.1.4.1.727.7.2.1.5
The current date.
OBJECT-TYPE    
  DisplayString  

sysClock 1.3.6.1.4.1.727.7.2.1.6
The current time.
OBJECT-TYPE    
  DisplayString  

sysDay 1.3.6.1.4.1.727.7.2.1.7
The current day.
OBJECT-TYPE    
  INTEGER sunday(1), monday(2), tuesday(3), wednesday(4), thursday(5), friday(6), saturday(7), not-applicable(254), not-available(255)  

sysAcceptLoop 1.3.6.1.4.1.727.7.2.1.8
Control of loopback on the WAN links. This parameter determines whether loopback on any link is accepted (YES) or not accepted (NO). The unit software detects the presence of a loopback condition on any WAN link. Setting ACCEPT LOOP to NO prevents the unit from using a link that has been placed in loopback mode either temporarily or accidentally.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

sysLinkTimeout-s 1.3.6.1.4.1.727.7.2.1.9
The delay, in seconds, before a WAN link is declared down during a link failure. This timeout can be used to prevent the accumulation of LINK DOWN alarms in the unit when brief link failures occur.
OBJECT-TYPE    
  INTEGER 0..1000  

sysTransitDelay-s 1.3.6.1.4.1.727.7.2.1.10
The maximum delay, in seconds, allowed to elapse between the reception and transmission of a forwarded frame by a bridge. a timer is started if a link report that it is too busy to transmit a frame. Frame that are nor processed within the transit delay are discarded.
OBJECT-TYPE    
  INTEGER 1..20  

sysDefaultIpAddr 1.3.6.1.4.1.727.7.2.1.11
Default IP address for the unit. This address is used for PVCR ports and PVCs that do not have a configures IP address (set with the IP LOCAL ADDR parameter for the port or PVC). It is a 4-byte value in dotted decimal representation with a maximum value of 255 for each byte. When set to 000.000.000.000, no default IP address is defined on the unit.
OBJECT-TYPE    
  IpAddress  

sysDefaultIpMask 1.3.6.1.4.1.727.7.2.1.12
Default IP subnet mask associated with the default IP address. It is configured like the default IP address: a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. The default IP mask identifies which bits of the IP address correspond to the physical network, and which bits correspond to host identifiers.
OBJECT-TYPE    
  IpAddress  

sysDefaultGateway 1.3.6.1.4.1.727.7.2.1.13
This is the gateway?s IP address to use when a destination is unknown. At this time, we?ll transmit all frame with unknown destination to this gateway.
OBJECT-TYPE    
  IpAddress  

sysRackId 1.3.6.1.4.1.727.7.2.1.15
ID of the Rack this board is plugged in
OBJECT-TYPE    
  INTEGER cs-product-only(0), rack-1(1), rack-2(2), rack-3(3), rack-4(4), not-applicable(254), not-available(255)  

sysPsAndFansMonitoring 1.3.6.1.4.1.727.7.2.1.16
The monitoring functionality of the Power Supplies and Fans.
OBJECT-TYPE    
  INTEGER cs-product-only(0), none(1), ps(2), fans(3), both(4), not-applicable(254), not-available(255)  

sysPsMonitoring 1.3.6.1.4.1.727.7.2.1.47
The monitoring functionality of the Power Supplies and Fans.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

sysSnmpTrapIpAddr1 1.3.6.1.4.1.727.7.2.1.17
Specific IP address to sent SNMP trap.
OBJECT-TYPE    
  IpAddress  

sysSnmpTrapIpAddr2 1.3.6.1.4.1.727.7.2.1.18
Specific IP address to sent SNMP trap.
OBJECT-TYPE    
  IpAddress  

sysSnmpTrapIpAddr3 1.3.6.1.4.1.727.7.2.1.19
Specific IP address to sent SNMP trap.
OBJECT-TYPE    
  IpAddress  

sysSnmpTrapIpAddr4 1.3.6.1.4.1.727.7.2.1.20
Specific IP address to sent SNMP trap.
OBJECT-TYPE    
  IpAddress  

sysThisPosId 1.3.6.1.4.1.727.7.2.1.30
ID of this board's position
OBJECT-TYPE    
  INTEGER cs-product-only(0), pos-1(1), pos-2(2), pos-3(3), pos-4(4), pos-5(5), pos-6(6), pos-7(7), pos-8(8), not-applicable(254), not-available(255)  

sysPosNr 1.3.6.1.4.1.727.7.2.1.31
The number of positions in the Rack this board belongs to (Always 8, hardware characteristic)
OBJECT-TYPE    
  INTEGER 0..32  

sysRacksNr 1.3.6.1.4.1.727.7.2.1.33
The total number of populated Racks in the system (1 to 4 racks)
OBJECT-TYPE    
  INTEGER 0..4  

sysPosTable 1.3.6.1.4.1.727.7.2.1.32
This table represents the entire rack this board belongs to. The number of entries is sysPosNr
OBJECT-TYPE    
  SEQUENCE OF  
    SysPosEntry

sysPosEntry 1.3.6.1.4.1.727.7.2.1.32.1
This entry contains the principal configurable parameters related to CS racks and positions
OBJECT-TYPE    
  SysPosEntry  

sysPosId 1.3.6.1.4.1.727.7.2.1.32.1.2
ID of the CS-Rack's position that the board at sysPosIndex is plugged in
OBJECT-TYPE    
  INTEGER cs-product-only(0), pos-1(1), pos-2(2), pos-3(3), pos-4(4), pos-5(5), pos-6(6), pos-7(7), pos-8(8), not-applicable(254), not-available(255)  

sysPosProduct 1.3.6.1.4.1.727.7.2.1.32.1.3
The Product descriptor of the board at sysPosIndex in the OID form e.g.: {lucent cleartrac7 product product-id}
OBJECT-TYPE    
  OBJECT IDENTIFIER  

sysPosRackId 1.3.6.1.4.1.727.7.2.1.32.1.4
ID of the CS-Rackds as it is configured in the board indexed by sysPosIndex. On a correctly configured installation, all positions in one rack must bear the same rackId
OBJECT-TYPE    
  INTEGER single-rack(0), rack-1(1), rack-2(2), rack-3(3), rack-4(4), not-applicable(254), not-available(255)  

sysPosIpAddr 1.3.6.1.4.1.727.7.2.1.32.1.5
the (Default) IP address for the unit. It means that, by managing this table in one position, we can see and alter the other position's IP addresses
OBJECT-TYPE    
  IpAddress  

ipaddrNr 1.3.6.1.4.1.727.7.2.32.1
The number ip addresses identifying this unit
OBJECT-TYPE    
  INTEGER  

ipaddrTable 1.3.6.1.4.1.727.7.2.32.2
A list of ip addresses entries. The number of entries is given by the value of ipaddrNr.
OBJECT-TYPE    
  SEQUENCE OF  
    IpaddrEntry

ipaddrEntry 1.3.6.1.4.1.727.7.2.32.2.1
This table is an index list of all ip addresses of this unit.
OBJECT-TYPE    
  IpaddrEntry  

ipaddrIndex 1.3.6.1.4.1.727.7.2.32.2.1.1
Tok_String
OBJECT-TYPE    
  INTEGER  

ipaddrAddr 1.3.6.1.4.1.727.7.2.32.2.1.2
Tok_String
OBJECT-TYPE    
  IpAddress  

ipaddrType 1.3.6.1.4.1.727.7.2.32.2.1.3
Tok_String
OBJECT-TYPE    
  INTEGER undef(0), global(1), wan(2), lan(3), proxy(4), pvc(5)  

ipaddrIfIndex 1.3.6.1.4.1.727.7.2.32.2.1.4
Tok_String
OBJECT-TYPE    
  INTEGER  

sysDLCI 1.3.6.1.4.1.727.7.2.1.34
The local DLCI address used as Srce field in the connection request to an ACT SDM-FP
OBJECT-TYPE    
  INTEGER  

sysExtensionNumLength 1.3.6.1.4.1.727.7.2.1.35
The number of digits that must be used to define a port Extension Number, or a Destination Extension Number in the Voice Mapping Table for this Node.
OBJECT-TYPE    
  INTEGER 1..5  

sysExtendedDigitsLength 1.3.6.1.4.1.727.7.2.1.36
This parameter sets the number of digits that must be entered into the telephone set when the Extension Number Source of a Voice Mapping Table entry is set to User.
OBJECT-TYPE    
  INTEGER 0..16  

sysDialTimer 1.3.6.1.4.1.727.7.2.1.37
This parameter specifies the amount of time the system should wait for a response to a Call Connect or Call Clear requests.
OBJECT-TYPE    
  INTEGER 0..10  

sysCountry 1.3.6.1.4.1.727.7.2.1.38
This parameter determines the type of ring, dial tone, ringback tone and busy tone that will be generated by the NetVoice card. To ensure that these signals are generated according to local standards, set this parameter to the country where the NetVoice is located.
OBJECT-TYPE    
  INTEGER 0..9999  

sysJitterBuf 1.3.6.1.4.1.727.7.2.1.39
The amount of jitter delay, in milliseconds, that the unit voice uses to compensate for the variable arrival time of packets.
OBJECT-TYPE    
  INTEGER 10..255  

sysRingFreq 1.3.6.1.4.1.727.7.2.1.40
the frequency in hertz, at which a ring is generated on locally attached equipment
OBJECT-TYPE    
  INTEGER voice-data-only(0), hz-17(1), hz-20(2), hz-25(3), hz-50(4), not-applicable(254), not-available(255)  

sysRingVolt 1.3.6.1.4.1.727.7.2.1.41
the voltage, in volts rms, at which a ring is generated on locally attached equipment.
OBJECT-TYPE    
  INTEGER voice-data-only(0), rms-Volts-60(1), rms-Volts-80(2), not-applicable(254), not-available(255)  

sysVoiceEncoding 1.3.6.1.4.1.727.7.2.1.42
SDM-9400 and V410 Only...
OBJECT-TYPE    
  INTEGER fp-product-only(0), aCode(1), bCode(2), not-applicable(254), not-available(255)  

sysVoiceClocking 1.3.6.1.4.1.727.7.2.1.43
SDM-9400 and V410 Only...
OBJECT-TYPE    
  INTEGER fp-product-only(0), aClock(1), bClock(2), not-applicable(254), not-available(255)  

sysVoiceLog 1.3.6.1.4.1.727.7.2.1.44
Enable logs (accounting) on voice/fax ports
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

sysSpeedDialNumLength 1.3.6.1.4.1.727.7.2.1.45
Number of digit of the MAP numbers
OBJECT-TYPE    
  INTEGER  

sysAutoSaveDelay 1.3.6.1.4.1.727.7.2.1.46
Number of seconds left after a modification and before saving in flash (0 : no auto save)
OBJECT-TYPE    
  INTEGER 0..255  

sysVoiceHighestPriority 1.3.6.1.4.1.727.7.2.1.48
When set to yes, the voice traffic has unconditionnaly the highest possible priority. When set to no, the voice priority is specified by sysVoiceClass.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

sysVoiceClass 1.3.6.1.4.1.727.7.2.1.49
Associate the voice traffic to a class priority. Effective only if sysVoiceHighestPriority is set to no
OBJECT-TYPE    
  INTEGER 1..8  

sysHuntForwardingAUnit 1.3.6.1.4.1.727.7.2.1.50
Hunt forwarding group A Unit name. Unit name where a busy call for hunt group A will be forwarded to
OBJECT-TYPE    
  DisplayString Size(0..16)  

sysHuntForwardingBUnit 1.3.6.1.4.1.727.7.2.1.51
Hunt forwarding group B Unit name. Unit name where a busy call for hunt group B will be forwarded to
OBJECT-TYPE    
  DisplayString Size(0..16)  

sysHuntForwardingADLCI 1.3.6.1.4.1.727.7.2.1.52
Hunt forwarding group A DLCI address. DLCI address where a busy call for hunt group A will be forwarded on an ACT SDM-FP PVC
OBJECT-TYPE    
  INTEGER  

sysHuntForwardingBDLCI 1.3.6.1.4.1.727.7.2.1.53
Hunt forwarding group B DLCI address. DLCI address where a busy call for hunt group B will be forwarded on an ACT SDM-FP PVC
OBJECT-TYPE    
  INTEGER  

sysHuntForwardingASvcAddress 1.3.6.1.4.1.727.7.2.1.54
Hunt forwarding group A SVC address. SVC address where a busy call for hunt group A will be forwarded on an ACT SDM-FP SVC. NOTE: sysHuntForwardingAUnit must be empty otherwise this parameter is ignored
OBJECT-TYPE    
  DisplayString  

sysHuntForwardingBSvcAddress 1.3.6.1.4.1.727.7.2.1.55
Hunt forwarding group A SVC address. SVC address where a busy call for hunt group A will be forwarded on an ACT SDM-FP SVC. NOTE: sysHuntForwardingBUnit must be empty otherwise this parameter is ignored
OBJECT-TYPE    
  DisplayString  

sysBackplaneRipVersion 1.3.6.1.4.1.727.7.2.1.56
When this parameter is set to V1, the RIP routing is done according to the RIP V1 standard. With RIP V2, broadcast or multicast can be used. With RIP V2 MULTICAST, only RIP V2 compliant devices will receive RIP frames.
OBJECT-TYPE    
  INTEGER disable(1), v1(2), v2-broadcast(3), v2-multicast(4), not-applicable(254), not-available(255)  

sysTrapRackandPos 1.3.6.1.4.1.727.7.2.1.57
Rack ID X 10 + Position ID.
OBJECT-TYPE    
  INTEGER  

proxyNumber 1.3.6.1.4.1.727.7.2.34.1
Number of proxies in this unit
OBJECT-TYPE    
  INTEGER  

proxyTable 1.3.6.1.4.1.727.7.2.34.2
List of proxies in this unit
OBJECT-TYPE    
  SEQUENCE OF  
    ProxyEntry

proxyEntry 1.3.6.1.4.1.727.7.2.34.2.1
This row presents the characteristics that uniquely identifies one proxy board.
OBJECT-TYPE    
  ProxyEntry  

proxyIndex 1.3.6.1.4.1.727.7.2.34.2.1.1
A unique value for each proxy board.
OBJECT-TYPE    
  INTEGER  

proxyComm 1.3.6.1.4.1.727.7.2.34.2.1.2
The name of the community used to access the proxy agent
OBJECT-TYPE    
  DisplayString Size(0..32)  

proxyIpAddr 1.3.6.1.4.1.727.7.2.34.2.1.3
IP address of this proxy agent
OBJECT-TYPE    
  IpAddress  

proxyIpMask 1.3.6.1.4.1.727.7.2.34.2.1.4
IP subnet mask of this proxy agent
OBJECT-TYPE    
  IpAddress  

proxyTrapIpAddr 1.3.6.1.4.1.727.7.2.34.2.1.5
Specific IP address to send SNMP trap.
OBJECT-TYPE    
  IpAddress  

proxyDefaultGateway 1.3.6.1.4.1.727.7.2.34.2.1.6
This is the IP address of the gateway handling routing to all nodes based on ACT'S proprietary NMS
OBJECT-TYPE    
  IpAddress  

intfNumber 1.3.6.1.4.1.727.7.2.30.1
The number of overall interfaces present on this system.
OBJECT-TYPE    
  INTEGER  

intfTable 1.3.6.1.4.1.727.7.2.30.2
A list of interface entries. The number of entries is given by the value of ifNumber.
OBJECT-TYPE    
  SEQUENCE OF  
    IntfEntry

intfEntry 1.3.6.1.4.1.727.7.2.30.2.1
This table presents the characteristics that uniquely identifies one interface.
OBJECT-TYPE    
  IntfEntry  

intfIndex 1.3.6.1.4.1.727.7.2.30.2.1.1
A unique value for each interface. Matches exaclty the ifIndex of the ifEntry in RFC-1213
OBJECT-TYPE    
  INTEGER  

intfDesc 1.3.6.1.4.1.727.7.2.30.2.1.2
A textual string containing information about a specific interface.
OBJECT-TYPE    
  DisplayString  

intfType 1.3.6.1.4.1.727.7.2.30.2.1.3
A unique type value for each interface.
OBJECT-TYPE    
  INTEGER wan-on-baseCard(1), voice-on-baseCard(2), wan-on-slot(3), voice-on-slot(4), lan-on-baseCard(5), lan-on-slot(6), proxy-on-slot(7), voice-control-on-slot(8), clock-extract-module(9), other(99), not-applicable(254), not-available(255)  

intfNumInType 1.3.6.1.4.1.727.7.2.30.2.1.4
The logical number of this interface amongst those having the same type.
OBJECT-TYPE    
  INTEGER 1..256  

intfSlot 1.3.6.1.4.1.727.7.2.30.2.1.5
The localization of this interface, whether on baseCard or in slot, and on what slot
OBJECT-TYPE    
  INTEGER baseCard(0), slot-1(1), slot-2(2), slot-3(3), slot-4(4), slot-5(5), slot-6(6), slot-7(7), slot-8(8), slot-A(9), slot-B(10), slot-C(11), slot-D(12), not-applicable(254), not-available(255)  

intfSlotType 1.3.6.1.4.1.727.7.2.30.2.1.6
A unique value for each interface.
OBJECT-TYPE    
  INTEGER baseCard(0), ethernet(1), vcf03(2), g703-E1(3), g703-T1(4), g703-E1-ii(5), g703-T1-ii(6), tokenring(7), voice(9), tic(16), tic-75(17), dvc(18), isdn-bri-voice(19), eic(21), eic-120(22), cem(23), vfc03r(51), proxy(36), unkown(9999), not-applicable(254), not-available(255)  

intfNumInSlot 1.3.6.1.4.1.727.7.2.30.2.1.7
The logical number of this interface within its slot.
OBJECT-TYPE    
  INTEGER 1..256  

intfModuleType 1.3.6.1.4.1.727.7.2.30.2.1.8
A unique value for each interface.
OBJECT-TYPE    
  INTEGER module-rs232-dce(0), module-rs232-dte(1), module-v35-dce(2), module-v35-dte(3), module-x21-dce(4), module-x21-dte(5), module-rs530-dce(6), module-rs530-dte(7), module-rs366A-dce(8), module-rs366A-dte(9), module-rs449-dce(10), module-rs449-dte(11), module-univ-dce(17), module-univ-dte(18), module-i430s-dte(19), module-i430u-dte(20), module-i431-T1-dte(21), module-i431-E1-dte(22), module-dsucsu(23), module-undef-dce(255), module-undef-dte(254), module-undef(253), not-applicable(252)  

intfSlotNumber 1.3.6.1.4.1.727.7.2.31.1
The number of overall slots actually presents on this system.
OBJECT-TYPE    
  INTEGER  

slotPortInSlotTable 1.3.6.1.4.1.727.7.2.31.2
This table maps a slot/PortInThisSlot coordinate to the corresponding ifIndex (in intfTable and ifTable)
OBJECT-TYPE    
  SEQUENCE OF  
    SlotPortInSlotEntry

slotPortInSlotEntry 1.3.6.1.4.1.727.7.2.31.2.1
One element of the above table
OBJECT-TYPE    
  SlotPortInSlotEntry  

slotSlot 1.3.6.1.4.1.727.7.2.31.2.1.1
The localization of this interface, whether on baseCard or in slot, and on what slot
OBJECT-TYPE    
  INTEGER baseCard(0), slot-1(1), slot-2(2), slot-3(3), slot-4(4), slot-5(5), slot-6(6), slot-7(7), slot-8(8), slot-A(9), slot-B(10), slot-C(11), slot-D(12), not-applicable(254), not-available(255)  

slotPortInSlot 1.3.6.1.4.1.727.7.2.31.2.1.2
The logical number of this interface within its slot.
OBJECT-TYPE    
  INTEGER 1..256  

slotIfIndex 1.3.6.1.4.1.727.7.2.31.2.1.3
A unique value for each interface. Matches exaclty the ifIndex of the ifEntry in RFC-1213
OBJECT-TYPE    
  INTEGER  

ifwanNumber 1.3.6.1.4.1.727.7.2.2.1
The number of wan interfaces present on this system.
OBJECT-TYPE    
  INTEGER  

ifwanTable 1.3.6.1.4.1.727.7.2.2.2
A list of interface entries. The number of entries is given by the value of ifwanNumber.
OBJECT-TYPE    
  SEQUENCE OF  
    IfwanEntry

ifwanEntry 1.3.6.1.4.1.727.7.2.2.2.1
This table contains the principal configurable parameters which are used for a particular wan interface.
OBJECT-TYPE    
  IfwanEntry  

ifwanIndex 1.3.6.1.4.1.727.7.2.2.2.1.1
A unique value for each interface.
OBJECT-TYPE    
  INTEGER  

ifwanDesc 1.3.6.1.4.1.727.7.2.2.2.1.2
A textual string containing information about a specific interface.
OBJECT-TYPE    
  DisplayString  

ifwanProtocol 1.3.6.1.4.1.727.7.2.2.2.1.3
Operating protocol for the WAN/user port.
OBJECT-TYPE    
  INTEGER off(1), p-sdlc(2), s-sdlc(3), hdlc(4), ddcmp(5), t-async(6), r-async(7), bsc(8), cop(9), pvcr(10), passthru(11), console(12), fr-net(17), fr-user(18), ppp(19), g703(28), x25(29), sf(31), not-applicable(254), not-available(255)  

ifwanSpeed-bps 1.3.6.1.4.1.727.7.2.2.2.1.4
Port speed or PVC CIR and BIR. 1200 to 64000 for DDCMP, BSC and COP. 110 to 115200 for TASYNC and RASYNC. 1200 to 128000 for PASSTRHU. 1200 to 2000000 for PVCs, PSDLC, SSDLC, HDLC, X25, FR-USER, FR-NET, PVCR.
OBJECT-TYPE    
  INTEGER 110..2000000  

ifwanFallBackSpeed-bps 1.3.6.1.4.1.727.7.2.2.2.1.5
Fallback speed for the transmitter. Fallback is available only if the unit is set for DCE internal clocking. If in DTE, the fallback rate is ignored. Set this parameter to 0 to disable fallback. For all user protocols except ASYNC and PASSTHRU. Applicable to SDM-8200, SDM-8300 and SDM-9530 only. The maximum for DDCMP, BSC and COP is 64000.
OBJECT-TYPE    
  INTEGER 0..2000000  

ifwanFallBackSpeedEnable 1.3.6.1.4.1.727.7.2.2.2.1.91
Enable the Fallback speed mechanism for the transmitter. Fallback is available only if the unit is set for DCE internal clocking. If in DTE, the fallback rate is ignored. Set this parameter to no to disable the fallback. The actual fallback speed is automatically computed and set by the unit. For all user protocols except ASYNC and PASSTHRU. Applicable to SDM-9350, SDM-9400, V352 and V410 only
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanInterface 1.3.6.1.4.1.727.7.2.2.2.1.6
Interface selection.
OBJECT-TYPE    
  INTEGER dce-rs232(0), dte-rs232(1), dce-v35(2), dte-v35(3), dce-x21(4), dte-x21(5), dce-rs530(6), dte-rs530(7), dce-rs366a(8), dte-rs366a(9), dce-rs449(10), dte-rs449(11), dte-aui(12), dte-tpe(13), autom(16), dce-univ(17), dte-univ(18), i430s(19), i430u(20), i431-t1(21), i431-e1(22), dsu-csu(23), dce-undef(255), dte-undef(254), type-undef(253)  

ifwanClocking 1.3.6.1.4.1.727.7.2.2.2.1.7
Clock source for the port. For ports on the processor/LAN interface board (ports 1 and 2) the clock source is automatically controlled by the unit, and cannot be changed. For all protocols.
OBJECT-TYPE    
  INTEGER internal(1), external(2), ipl(3), itb(4), async(5), iso-int(6), iso-ext(7), t1-e1-B-Rcvd(11), t1-e1-A-Rcvd(12), t1-e1-Local(13), not-applicable(254), not-available(255)  

ifwanCoding 1.3.6.1.4.1.727.7.2.2.2.1.8
For SDLC and HDLC protocols only. Bit coding for CRC purposes. For NORMAL and NRZI coding the computed CRC is preset at 1. For normal coding with CRC0 (CRC0-NML) and NRZI coding with CRC0 (CRC0-NZI) the computed CRC is preset at 0. The values NRZ-CRC0 and NRZI-CRC0 are available for the HDLC protocol only.
OBJECT-TYPE    
  INTEGER nrz(1), nrzi(2), nrz-crc0(3), nrzi-crc0(4), not-applicable(254), not-available(255)  

ifwanModem 1.3.6.1.4.1.727.7.2.2.2.1.9
Modem control signal operating mode. If the port is DCE this parameter controls the operating mode of the DCD control signal. In STATIC mode the DCD signal is active at all times. In DYNAMIC mode it is active only when a frame is transmitted. If the port is DTE this parameter controls the operating mode of the RTS control signal. In STATIC mode the RTS signal is active at all times. In DYNAMIC mode it is active only when a frame is transmitted.
OBJECT-TYPE    
  INTEGER static(1), dynamic(2), statpass(3), dynapass(4), statfix(5), dynafix(6), not-applicable(254), not-available(255)  

ifwanTxStart 1.3.6.1.4.1.727.7.2.2.2.1.10
For all user protocols except ASYNC, PASSTH and COP. Transmit start level. This is the number of characters that are accumulated before the transmitter is enabled when a frame is incomplete. When set to MAX, the transmitter is enabled only when a complete frame has been accumulated by the unit. This value prevents underruns but can introduce unnecessary delays. When the transmit start level is set to a numeric value, the transmitter is enabled at that level even if a frame coming from the remote unit has not been completely received. If the port is in DCE-INTRN mode and fallback is enabled, the transmitter falls back when the number of characters of an incomplete frame in the output queue goes below the transmit start level. Otherwise, no fallback occurs.
OBJECT-TYPE    
  INTEGER auto(0), max(1), byte-48(2), byte-96(3), byte-144(4), byte-192(5), byte-256(6), byte-512(7), byte-1024(8), byte-2048(9), byte-8(10), byte-16(11), byte-24(12), byte-32(13), not-applicable(254), not-available(255)  

ifwanTxStartCop 1.3.6.1.4.1.727.7.2.2.2.1.89
For COP protocol only. Transmit start level. This is the number of characters that are accumulated before the transmitter is enabled when a frame is incomplete. When set to MAX, the transmitter is enabled only when a complete frame has been accumulated by the unit. This value prevents underruns but can introduce unnecessary delays. When the transmit start level is set to a numeric value, the transmitter is enabled at that level even if a frame coming from the remote unit has not been completely received. If the port is in DCE-INTRN mode and fallback is enabled, the transmitter falls back when the number of characters of an incomplete frame in the output queue goes below the transmit start level. Otherwise, no fallback occurs.
OBJECT-TYPE    
  INTEGER auto(0), max(1), byte-8(2), byte-16(3), byte-24(4), byte-32(5), byte-40(6), byte-48(7), byte-96(8), byte-144(9), byte-192(10), byte-256(11), byte-512(12), byte-1024(13), byte-2048(14), not-applicable(254), not-available(255)  

ifwanTxStartPass 1.3.6.1.4.1.727.7.2.2.2.1.90
For PASSTRHU protocol only. Transmit start level. This is the number of transparent blocks that are accumulated before the transmitter is enabled when a frame is incomplete.
OBJECT-TYPE    
  INTEGER 3..12  

ifwanIdle 1.3.6.1.4.1.727.7.2.2.2.1.11
For HDLC, SDLC and COP protocols only. Transmitter idle state, which determines the characters to be sent when no data frame is transmitted. When configured as FLAG, the transmitter continuously sends 7E (flags). When configured as MARK, it continuously sends 1. When configured as MARKD, the MARK IDLE state is postponed 20 msec after the end of a frame. When configured as SPACE, it continuously sends 0.
OBJECT-TYPE    
  INTEGER space(1), mark(2), flag(3), markd(4), not-applicable(254), not-available(255)  

ifwanDuplex 1.3.6.1.4.1.727.7.2.2.2.1.12
Port duplex mode. When set to FULL (DUPLEX), the SDLC driver can transmit INFO frames to a secondary port while polling another secondary port.
OBJECT-TYPE    
  INTEGER half(1), full(2), not-applicable(254), not-available(255)  

ifwanGroupPoll 1.3.6.1.4.1.727.7.2.2.2.1.13
For P-SDLC and S-SDLC protocols only. Group poll enabled or disabled. When this parameter is set to YES, the group poll feature is enabled, using the address set with the group address parameter, described below. When this parameter is set to NO, the group poll feature is disabled.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanGroupAddress 1.3.6.1.4.1.727.7.2.2.2.1.14
For P-SDLC and S-SDLC protocols only. Group address. This parameter is used when the group poll feature is enabled (see ifwanGroupPoll parameter, above).
OBJECT-TYPE    
  STRING Size(2)  

ifwanPollDelay-ms 1.3.6.1.4.1.727.7.2.2.2.1.15
The wait time, in milliseconds, before transmitting a poll.
OBJECT-TYPE    
  INTEGER 0..1000  

ifwanFrameDelay 1.3.6.1.4.1.727.7.2.2.2.1.16
For HDLC protocol only. Delay, in milliseconds, added between each frame transmitted on the unit port. This delay is required by some DTE equipment operating at speeds higher than 56 Kbps.
OBJECT-TYPE    
  INTEGER delay-0p0-ms(1), delay-0p5-ms(2), delay-1p0-ms(3), delay-1p5-ms(4), delay-2p0-ms(5), not-applicable(254), not-available(255)  

ifwanFormat 1.3.6.1.4.1.727.7.2.2.2.1.17
For ASYNC and COP protocols only. Character format. The parameter values are different for the ASYNC and COP protocols. ASYNC Protocols: The parameter defines the number of data bits per character, the parity bit usage, number of stop bits and idle characters. When not specified in the parameter value, the number of stop bits is 1. 8N-2STOP configures the port for 8 bits, no parity and 2 stop bits. Values: 8-NONE, 8-ODD, 8-EVEN, 7-NONE, 7-ODD, 7-EVEN, 7 SPACE, 7-MARK, 7-IGNORE, 8N-2STOP COP Protocol: The parameter defines the number of bits per character only. Values: 8 bits, 6 bits
OBJECT-TYPE    
  INTEGER fmt-8-none(1), fmt-7-none(2), fmt-7-odd(3), fmt-7-even(4), fmt-7-space(5), fmt-7-mark(6), fmt-7-ignore(7), fmt-8-even(8), fmt-8-odd(9), fmt-8n-2stop(10), fmt-8-bits(11), fmt-6-bits(12), sync(13), async(14), not-applicable(254), not-available(255)  

ifwanSync 1.3.6.1.4.1.727.7.2.2.2.1.18
For COP protocol only. The hexadecimal value of the synchronization character.
OBJECT-TYPE    
  STRING Size(2)  

ifwanDropSyncCounter 1.3.6.1.4.1.727.7.2.2.2.1.19
For COP protocol only. Drop synchronization counter. This parameter defines the number of contiguous desynchronization characters that must be received before the unit drops synchronization and closes the frame.
OBJECT-TYPE    
  INTEGER 1..100  

ifwanDropSyncCharacter 1.3.6.1.4.1.727.7.2.2.2.1.20
For COP protocol only. The hexadecimal value of the desynchronization character. This parameter defines the value of the desynchronization character in hexadecimal.
OBJECT-TYPE    
  STRING Size(1)  

ifwanMode 1.3.6.1.4.1.727.7.2.2.2.1.21
For PVCR protocol only. Operating mode of the WAN link. This parameter defines the WAN link as a dedicated link, a backup link or a Bandwidth On Demand link. The ANSWER mode is used for the link that responds to calls. When you install a backup or Bandwidth On Demand (BOD) link between two units, one unit must be configured in call mode (CALL-BACKUP or CALL-BOD) and the other as ANSWER. The INACTIVE mode is used to turn off the link.
OBJECT-TYPE    
  INTEGER inactive(1), dedicated(2), answer(3), call-backup(4), call-bod(5), wait-user(6), not-applicable(254), not-available(255)  

ifwanBodCall-s 1.3.6.1.4.1.727.7.2.2.2.1.22
The call trigger period, in seconds, for the Bandwidth ON Demand function. This defines the period of time during which the combined WAN link usage must be a the BOD level (define with the BOD LEVEL parameter) or higher before another WAN link will be activated. It is, in effect, a means of validating the requirement for a new link
OBJECT-TYPE    
  INTEGER 1..1000  

ifwanBodHang-s 1.3.6.1.4.1.727.7.2.2.2.1.23
The hold time, in seconds, for minimum link activation under the Bandwidth On Demand function. This defines the minimum period of time during which a newly added WAN link will remain activated, even if the usage level drops rapidly. This parameter can prevent unnecessary link activation/deactivation procedures when the traffic flow fluctuates widely.
OBJECT-TYPE    
  INTEGER 1..1000  

ifwanBodLevel 1.3.6.1.4.1.727.7.2.2.2.1.24
The call trigger level for the Bandwidth On Demand function. It represents the combined WAN link usage level, given as a percentage of the total bandwidth, at which another link should be activated. This defines a threshold at which another wan link will be added to ease the traffic flow.
OBJECT-TYPE    
  INTEGER 5..95  

ifwanBackupCall-s 1.3.6.1.4.1.727.7.2.2.2.1.25
Delay, in seconds, before activating the backup link when a line failure has occurred on a dedicated link.
OBJECT-TYPE    
  INTEGER 1..1000  

ifwanDialTimeout-s 1.3.6.1.4.1.727.7.2.2.2.1.92
Delay, in seconds, allowed to establish a dial-up backup link.
OBJECT-TYPE    
  INTEGER 30..1000  

ifwanBackupHang-s 1.3.6.1.4.1.727.7.2.2.2.1.26
Delay, in seconds, before deactivating the backup WAN link after the dedicated link has been restored.
OBJECT-TYPE    
  INTEGER 1..1000  

ifwanPortToBack 1.3.6.1.4.1.727.7.2.2.2.1.27
The WAN link that this port backs up. Backup links can be configured to monitor and backup a specific link (1..8) any link that fails (ANY) or all other unit links (ALL). NOTE: The number of available links varies with each product.
OBJECT-TYPE    
  INTEGER any(15), all(16), port-1(1), port-2(2), port-3(3), port-4(4), port-5(5), port-6(6), port-7(7), port-8(8), not-applicable(254), not-available(255)  

ifwanDialer 1.3.6.1.4.1.727.7.2.2.2.1.28
Backup link dialer mode
OBJECT-TYPE    
  INTEGER dTR(1), x21-L1(2), x21-L2(3), v25-H(4), v25-B(5), aT-9600(6), aT-19200(7), not-applicable(254), not-available(255)  

ifwanRemoteUnit 1.3.6.1.4.1.727.7.2.2.2.1.29
Remote unit to which data from this port should be directed
OBJECT-TYPE    
  DisplayString  

ifwanClassNumber 1.3.6.1.4.1.727.7.2.2.2.1.30
The priority class for data from this port. Classes are defined according to bandwidth weight.
OBJECT-TYPE    
  INTEGER 1..8  

ifwanRingNumber 1.3.6.1.4.1.727.7.2.2.2.1.31
The ring number of the remote Token-ring LAN, required for source routing of Token-Ring data via the unit.
OBJECT-TYPE    
  STRING Size(2)  

ifwanIpAddress 1.3.6.1.4.1.727.7.2.2.2.1.32
IP address for the local port. This address is a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. When set to 000.000.000.000, no IP address is defined for this port. In this case the unit will use the default IP address defined with the global DEFAULT IP ADDR parameter.
OBJECT-TYPE    
  IpAddress  

ifwanSubnetMask 1.3.6.1.4.1.727.7.2.2.2.1.33
Subnet mask associated with the port IP address. It is configured like the IP address: a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. The subnet mask identifies which bits of the IP address correspond to the physical network, and which bits correspond to host identifiers.
OBJECT-TYPE    
  IpAddress  

ifwanMaxFrame 1.3.6.1.4.1.727.7.2.2.2.1.34
Maximum frame size, in octets. This parameter determines the largest datagram that can be sent or received on the interface in one IP frame. Datagrams larger than the maximum frame size are divided into fragments before transmission, the reassembled at the remote end.
OBJECT-TYPE    
  INTEGER 128..8192  

ifwanCompression 1.3.6.1.4.1.727.7.2.2.2.1.36
Use compression on the WAN link connection to the remote unit. With compression, the available bandwidth is used more efficiently. When compression is not used, higher speeds can be obtained on the link.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanPriority 1.3.6.1.4.1.727.7.2.2.2.1.37
Priority assigned to the WAN port for the Spanning Tree algorithm.
OBJECT-TYPE    
  INTEGER 0..255  

ifwanTimeout 1.3.6.1.4.1.727.7.2.2.2.1.39
The wait for ACK timeout before retransmitting a frame on the WAN link.
OBJECT-TYPE    
  INTEGER 1000..30000  

ifwanRetry 1.3.6.1.4.1.727.7.2.2.2.1.40
Maximum number of successive retries before the WAN link is declared down.
OBJECT-TYPE    
  INTEGER 1..1000  

ifwanRemotePort 1.3.6.1.4.1.727.7.2.2.2.1.41
For all user protocols except SDLC and PVCR. The remote port to which data from the local port is sent. Specify the port number on the remote unit.
OBJECT-TYPE    
  INTEGER 1..255  

ifwanFlowControl 1.3.6.1.4.1.727.7.2.2.2.1.42
Congestion flow control notification. If the FLOW CTRL parameter is ON, the unit will set the Forward and Backward Congestion Bits in the header of the active PVC frame when congestion occurs on the unit port. Forward data congestion affects data transmitted from Frame Relay equipment to the unit port. Backward data congestion affects data transmitted from the unit to the Frame Relay equipment. If the FLOW CTRL parameter is OFF, the unit does not set the congestion bits. In this cas, they are reset to zero
OBJECT-TYPE    
  INTEGER off(1), on(2), not-applicable(254), not-available(255)  

ifwanMgmtInterface 1.3.6.1.4.1.727.7.2.2.2.1.43
Frame Relay Management Protocol. The LMI (Local Management Interface) uses the reserved DLCI address 1023. The ANNEX-D and the Q-933 protocols uses the reserved DLCI address 0. Set this parameter according to the Management Interface Protocol used on the network connected to the unit port.
OBJECT-TYPE    
  INTEGER lmi(1), annex-d(2), q-933(3), none(4), not-applicable(254), not-available(255)  

ifwanEnquiryTimer-s 1.3.6.1.4.1.727.7.2.2.2.1.44
Frame Relay Enquiry Timer. The unit polls the network with STATUS ENQUIRY frames when this timer expires.
OBJECT-TYPE    
  INTEGER 1..30  

ifwanReportCycle 1.3.6.1.4.1.727.7.2.2.2.1.45
Full Status Enquiry Cycle. The value of this parameter determines the number of STATUS ENQUIRY frames that the unit will send before sending a full status enquiry to the network. In response to a full status enquiry the network will send a full status report. This report indicates the currently active PVC on the network. The unit uses this information to determine if a particular PVC is ready to receive data. It is also used in determining the number of restart errors for PVCs in PVCR mode.
OBJECT-TYPE    
  INTEGER 1..256  

ifwanIpRip 1.3.6.1.4.1.727.7.2.2.2.1.46
When this parameter is set to V1, the RIP routing is done according to the RIP V1 standard. With RIP V2, broadcast or multicast can be used. With RIP V2 MULTICAST, only RIP V2 compliant devices will receive RIP frames.
OBJECT-TYPE    
  INTEGER disable(1), v1(2), v2-broadcast(3), v2-multicast(4), not-applicable(254), not-available(255)  

ifwanCllm 1.3.6.1.4.1.727.7.2.2.2.1.47
Frame Relay CLLM control. The value of this parameter determines the behavior of the unit regarding the Consolidated Link Management Option. When set to OFF, CLLM messages received are discarded and none are generated. When set to ON, CLLM messages are generated on the FR-NET when PVC becomes congested or blocked and frames received are analyzed.
OBJECT-TYPE    
  INTEGER off(1), on(2), not-applicable(254), not-available(255)  

ifwanIpxRip 1.3.6.1.4.1.727.7.2.2.2.1.48
if this parameter is enable, the unit will generate IPX RIP frame on that interface every minute, otherwise the unit will discard all IPX RIP frame received and no one will be generated on that port.
OBJECT-TYPE    
  INTEGER disable(1), enable(2), not-applicable(254), not-available(255)  

ifwanIpxSap 1.3.6.1.4.1.727.7.2.2.2.1.49
if this parameter is enable, the unit will generate IPX SAP frame on that interface every minute, otherwise the unit will discard all IPX SAP frame received and no one will be generated on that port.
OBJECT-TYPE    
  INTEGER disable(1), enable(2), not-applicable(254), not-available(255)  

ifwanIpxNetNum 1.3.6.1.4.1.727.7.2.2.2.1.50
This value identify the IPX network number which the unit is connected to
OBJECT-TYPE    
  STRING Size(4)  

ifwanRxFlow 1.3.6.1.4.1.727.7.2.2.2.1.52
For R-ASYNC protocol only. Flow control on the receiver. This parameter describes the method used by the unit to control the flow of data received from the attached equipment. Flow control is applied when the number of characters on input exceeds a predefined threshold.
OBJECT-TYPE    
  INTEGER none(5), xon-Xoff(1), hardware(2), not-applicable(254), not-available(255)  

ifwanTxFlow 1.3.6.1.4.1.727.7.2.2.2.1.53
For R-ASYNC protocol only. Flow control on the transmitter. This parameter describes the method used by the attached equipment to control the flow of data transmitted by the unit.
OBJECT-TYPE    
  INTEGER none(5), xon-Xoff(1), hardware(2), not-applicable(254), not-available(255)  

ifwanTxHold-s 1.3.6.1.4.1.727.7.2.2.2.1.54
For R-ASYNC protocol only. Transmitter hold time. This parameter defines the maximum hold time that the transmitter can be blocked due to flow control. There is no hold time limit if TX HOLD is configured as 0 seconds.
OBJECT-TYPE    
  INTEGER 0..1000  

ifwanDsOSpeed-bps 1.3.6.1.4.1.727.7.2.2.2.1.55
Speed of a DS0 channel: 64000 bps or 56000 bps.
OBJECT-TYPE    
  INTEGER bps-64000(1), bps-56000(2), not-applicable(254), not-available(255)  

ifwanFraming 1.3.6.1.4.1.727.7.2.2.2.1.58
Framing format (ESF or D4). ***** NOTE: This parameter applies only to TIC, not to EIC.
OBJECT-TYPE    
  INTEGER esf(2), d4(3), other(4), not-applicable(254), not-available(255)  

ifwanTerminating 1.3.6.1.4.1.727.7.2.2.2.1.59
Terminating (NT indicate Network terminating and TE indicate terminal terminating).
OBJECT-TYPE    
  INTEGER tE(1), nT(2), not-applicable(254), not-available(255)  

ifwanCrc4 1.3.6.1.4.1.727.7.2.2.2.1.60
CRC-4 procedure enable or disable.
OBJECT-TYPE    
  INTEGER disable(1), enable(2), not-applicable(254), not-available(255)  

ifwanLineCoding 1.3.6.1.4.1.727.7.2.2.2.1.61
1's density control or zero suppression over the line.
OBJECT-TYPE    
  INTEGER ami-e1(0), hdb3-e1(1), b8zs-t1(2), ami-t1(5), other(4), b7sz-t1(7), not-applicable(254), not-available(255)  

ifwanBChannels 1.3.6.1.4.1.727.7.2.2.2.1.62
This parameter permits to enable two independent 64 kbits/s channel for use as B-channels.
OBJECT-TYPE    
  INTEGER disable(1), b1(2), b2(3), b1-plus-b2(4), not-applicable(254), not-available(255)  

ifwanMultiframing 1.3.6.1.4.1.727.7.2.2.2.1.63
The Multiframing provides a layer1 signalling capability between the TE and the NT.
OBJECT-TYPE    
  INTEGER disable(1), enable(2), not-applicable(254), not-available(255)  

ifwanOspfEnable 1.3.6.1.4.1.727.7.2.2.2.1.64
Indicates whether or not OSPF is enabled on this interface.
OBJECT-TYPE    
  INTEGER disable(1), enable(2), not-applicable(254), not-available(255)  

ifwanOspfAreaId 1.3.6.1.4.1.727.7.2.2.2.1.65
Identifies the area to which this interface belongs.
OBJECT-TYPE    
  IpAddress  

ifwanOspfTransitDelay 1.3.6.1.4.1.727.7.2.2.2.1.66
The estimated number of seconds it takes to transmit a Link State Update Packet over this interface.
OBJECT-TYPE    
  INTEGER 1..360  

ifwanOspfRetransmitInt 1.3.6.1.4.1.727.7.2.2.2.1.67
The number of seconds between like state advertisement retransmissions for adjacencies belonging to this interface. Also used when retransmitting Database Description and Link State Request Packets.
OBJECT-TYPE    
  INTEGER 1..360  

ifwanOspfHelloInt 1.3.6.1.4.1.727.7.2.2.2.1.68
The length of time, in seconds, between the Hello Packets that the router sends on the interface. This value is advertised in the router's Hello Packets. It must be the same for all routers attached to a common network. The smaller the HelloInterval, the faster topological changes will be detected, but more OSPF routing protocol traffic will ensue.
OBJECT-TYPE    
  INTEGER 1..360  

ifwanOspfDeadInt 1.3.6.1.4.1.727.7.2.2.2.1.69
After ceasing to hear a router's Hello Packets, the number of seconds before its neighbors declare the router down. This is also advertised in the router's Hello Packets in their RouterDeadInterval field. This value again bust be the same for all routers attached to a common network.
OBJECT-TYPE    
  INTEGER 1..2000  

ifwanOspfPassword 1.3.6.1.4.1.727.7.2.2.2.1.70
This configured data allows the authentication procedure to generate and/or verify the authentication field in the OSPF header. This value again must be the same for all routers attached to a common network.
OBJECT-TYPE    
  DisplayString  

ifwanOspfMetricCost 1.3.6.1.4.1.727.7.2.2.2.1.71
The cost of sending a packet on the interface, expressed in the link state metric. This is advertised as the link cost for this interface in the router's router links advertisement.
OBJECT-TYPE    
  INTEGER 1..65534  

ifwanChUse 1.3.6.1.4.1.727.7.2.2.2.1.72
A 32 byte string describing the use of each DS0 of the span: - '-' or 'i' means off - 'P' means used in passthru mode - 'V' means used as a voice channel - 'R' means reserved ( cannot be set, valid only on EICs) for example: RV--------------R--------------P DS0 timeslot 1 is represent by the left most character. Timeslot 1 and 17 are always reserved when using an E1 span. When using a T1 span all DS0 timeslots are available. This would mean that the DS0 timeslot 1 is used as a reserved channel, the DS0 timeslot 2 is used as a voice channel and the DS0 timeslot 17 is used as a reserved channel and DS0 timeslot 32 is used as a passthru channel
OBJECT-TYPE    
  DisplayString  

ifwanGainLimit 1.3.6.1.4.1.727.7.2.2.2.1.77
this object specifies the gain to be applied on received DS1 signal. ***** NOTE: This parameter applies only to TIC, not to EIC.
OBJECT-TYPE    
  INTEGER db-30(1), db-36(2), not-applicable(254), not-available(255)  

ifwanSignaling 1.3.6.1.4.1.727.7.2.2.2.1.78
Specifies what type of signalling is in effect on this port. NOTE: 1) none and t1-rob-bit are valid only for a TIC card. 2) e1-cas, trsp-orig, trsp-answ and qsig are valid only for a EIC card. 3) e1-ccs is no longer used.
OBJECT-TYPE    
  INTEGER none(1), t1-rob-bit(2), e1-cas(3), e1-ccs(4), trsp-orig(5), trsp-answ(6), qsig(7), not-applicable(254), not-available(255)  

ifwanIdleCode 1.3.6.1.4.1.727.7.2.2.2.1.79
this object specifies the byte to be transmitted when no real data to transmit
OBJECT-TYPE    
  STRING Size(1)  

ifwanLineBuild 1.3.6.1.4.1.727.7.2.2.2.1.80
this object specifies the build out to be applied on transmitted DS1 signal. ***** NOTE: This parameter applies only to TIC, not to EIC.
OBJECT-TYPE    
  INTEGER ft0-to-133(0), ft133-to-266(1), ft266-to-399(2), ft399-to-533(3), ft533-to-655(4), dbMinus7point5(5), dbMinus15(6), dbMinus22point5(7), ohm-75(8), ohm-120(9), not-applicable(254), not-available(255)  

ifwanT1E1Status 1.3.6.1.4.1.727.7.2.2.2.1.84
This parameter sets the activation status of the T1 port, that is, the preferred T1 port state (enabled or disabled).
OBJECT-TYPE    
  INTEGER disable(1), enable(2), not-applicable(254), not-available(255)  

ifwanT1E1LoopBack 1.3.6.1.4.1.727.7.2.2.2.1.85
This object is used to enable/disable loopback on T1/E1 interfaces. The types of loopback depend on the type of T1/E1 interface used.
OBJECT-TYPE    
  INTEGER disable(1), enable(2), lev1-local(3), lev2-local(4), echo(5), not-applicable(254), not-available(255)  

ifwanChExp 1.3.6.1.4.1.727.7.2.2.2.1.86
A 32 byte string describing the cross connection of every DS0 of this interface: - DS0 timeslot 1 is represent by the left most character. - every byte of the field correspond to a DS0 channel assign to a specific DVC slot number, i.e. DS0 number 8 is represented by the second byte of the string and represent timeslot 2 crossconnect to a DVC in slot 8, and so on up to DS0 number 32. - a digit k ( k in the range '1' to '8') placed at the nth position in the string means that the nth DS0 is crossconnected to the expansion slot number k for example: R8--------------R-------------76 Timeslot 1 and 17 are always reserved when using an E1 span. When using a T1 span all DS0 timeslots are available. This would mean that the DS0 nr 2 is crossconnected to slot 8, DS0 nr 31 is crossconnected to a DVC in slot 7, DS0 nr 32 is crossconnected to a DVC in slot 6. The - or I characters means that there is no cross connection.
OBJECT-TYPE    
  DisplayString  

ifwanT1E1InterBit 1.3.6.1.4.1.727.7.2.2.2.1.87
Use this parameter to enable or disable setting of the International Bit (I-bit).
OBJECT-TYPE    
  INTEGER disable(1), enable(2), not-applicable(254), not-available(255)  

ifwanEncodingLaw 1.3.6.1.4.1.727.7.2.2.2.1.88
The PCM coding law in effect on this interface. Configuration CFG-WPORT-ENCODING-LAW
OBJECT-TYPE    
  INTEGER aLaw(0), muLaw(1), not-applicable(254), not-available(255)  

ifwanCellPacketization 1.3.6.1.4.1.727.7.2.2.2.1.93
Indicates whether or not cell packetization is enabled on this interface.
OBJECT-TYPE    
  INTEGER disable(1), enable(2), not-applicable(254), not-available(255)  

ifwanMaxChannels 1.3.6.1.4.1.727.7.2.2.2.1.94
Indicates the maximum number of voice channels permitted on this port.
OBJECT-TYPE    
  INTEGER 0..10000  

ifwanCondLMIPort 1.3.6.1.4.1.727.7.2.2.2.1.95
Indicates which FR-USER port will be used as a reference port to respond to LMI request. If 'none' is specified, the FR-NET port will always answer to LMI request. If a port is specified, the FR-NET port will answer to LMI request only if the indicated port receives answers to its LMI request.
OBJECT-TYPE    
  INTEGER none(0), not-applicable(254), not-available(255)  

ifwanExtNumber 1.3.6.1.4.1.727.7.2.2.2.1.96
Port extension number
OBJECT-TYPE    
  DisplayString  

ifwanDestExtNumber 1.3.6.1.4.1.727.7.2.2.2.1.97
Destination extension number
OBJECT-TYPE    
  DisplayString  

ifwanConnTimeout-s 1.3.6.1.4.1.727.7.2.2.2.1.98
This parameter determines the maximum amount of time, in seconds, that the voice port who initiates the call will wait for a call connect confirmed
OBJECT-TYPE    
  INTEGER 10..30  

ifwanSvcAddressType 1.3.6.1.4.1.727.7.2.2.2.1.99
This parameter determines the SVC address type supported by this frame relay port (NONE, E.164 or X.121)
OBJECT-TYPE    
  INTEGER none(1), e-164(2), x-121(3)  

ifwanSvcNetworkAddress 1.3.6.1.4.1.727.7.2.2.2.1.100
Local SVC Network address.
OBJECT-TYPE    
  DisplayString  

ifwanSvcMaxTxTimeoutT200 1.3.6.1.4.1.727.7.2.2.2.1.101
Maximum Tx Acknowledge timeout (T200).
OBJECT-TYPE    
  INTEGER 1..5  

ifwanSvcInactiveTimeoutT203 1.3.6.1.4.1.727.7.2.2.2.1.102
Maximum number of seconds without activity (T203).
OBJECT-TYPE    
  INTEGER 1..60  

ifwanSvcIframeRetransmissionsN200 1.3.6.1.4.1.727.7.2.2.2.1.103
Maximum number of I frame retransmission's (N200).
OBJECT-TYPE    
  INTEGER 1..16  

ifwanSvcSetupTimeoutT303 1.3.6.1.4.1.727.7.2.2.2.1.104
Response time-out for Q933 setup message (T303).
OBJECT-TYPE    
  INTEGER 1..30  

ifwanSvcDisconnectTimeoutT305 1.3.6.1.4.1.727.7.2.2.2.1.105
Response time-out for Q933 disconnect message (T305).
OBJECT-TYPE    
  INTEGER 1..30  

ifwanSvcReleaseTimeoutT308 1.3.6.1.4.1.727.7.2.2.2.1.106
Response time-out for Q933 release message (T308).
OBJECT-TYPE    
  INTEGER 1..30  

ifwanSvcCallProceedingTimeoutT310 1.3.6.1.4.1.727.7.2.2.2.1.107
Response time-out for Q933 call proceeding message (T310).
OBJECT-TYPE    
  INTEGER 1..30  

ifwanSvcStatusTimeoutT322 1.3.6.1.4.1.727.7.2.2.2.1.108
Response time-out for Q933 status enquiry message (T322).
OBJECT-TYPE    
  INTEGER 1..30  

ifwanTeiMode 1.3.6.1.4.1.727.7.2.2.2.1.109
Object specific to the ISDN BRI Voice card. Indicates the TEI mode used for the interface. When Dynamic is selected, the TEI is negotiated between the NT and the TE devices. Whenever Fixed is selected, the TEI value 0 is used to establish the session.
OBJECT-TYPE    
  INTEGER dynamic(1), fixed(2), not-applicable(254), not-available(255)  

ifwanDigitNumber 1.3.6.1.4.1.727.7.2.2.2.1.110
Object specific to the ISDN BRI Voice card. It contains the number of digits to wait for before the setup request is forwarded on the port. This object is usefull only when the ifwanTerminating is set to NT.
OBJECT-TYPE    
  INTEGER 0..8  

ifwanMsn1 1.3.6.1.4.1.727.7.2.2.2.1.111
Object specific to the ISDN BRI Voice card. Contains the First ISDN number on which the port will accept an incoming connection request. This object is usefull only when ifwanTerminating is set to TE.
OBJECT-TYPE    
  DisplayString  

ifwanMsn2 1.3.6.1.4.1.727.7.2.2.2.1.112
Object specific to the ISDN BRI Voice card. Second ISDN number on which the port will accept an incoming connection request. This object is usefull only when ifwanTerminating is set to TE while ifwanTeiMode is set to Dynamic.
OBJECT-TYPE    
  DisplayString  

ifwanMsn3 1.3.6.1.4.1.727.7.2.2.2.1.113
Object specific to the ISDN BRI Voice card. Third ISDN number on which the port will accept an incoming connection request. This object is usefull only when ifwanTerminating is set to TE while ifwanTeiMode is set to Dynamic.
OBJECT-TYPE    
  DisplayString  

ifwanX25Encapsulation 1.3.6.1.4.1.727.7.2.2.2.1.114
Defines the encapsulation method used to transport X25 over frame relay.
OBJECT-TYPE    
  INTEGER annex-f(1), annex-g(2), not-applicable(254), not-available(255)  

ifwanPvcNumber 1.3.6.1.4.1.727.7.2.2.2.1.115
PVC this port will use to carry X25 traffic over frame relay.
OBJECT-TYPE    
  INTEGER  

ifwanQsigPbxAb 1.3.6.1.4.1.727.7.2.2.2.1.116
Object specific to the E1 card, when QSIG signaling is used. Specifies the DTE/DCE operation mode of the QSIG port.
OBJECT-TYPE    
  INTEGER a(1), b(2), not-applicable(254), not-available(255)  

ifwanQsigPbxXy 1.3.6.1.4.1.727.7.2.2.2.1.117
Object specific to the E1 card, when QSIG signaling is used. Object used as an arbitrator in case of collisions between the E1 card and the connected device (i.e. the local PBX). One side of the connection has to be set to X while the other side of the connection has to be set to Y.
OBJECT-TYPE    
  INTEGER x(1), y(2), not-applicable(254), not-available(255)  

ifwanIpRipTxRx 1.3.6.1.4.1.727.7.2.2.2.1.118
This parameter allows RIP frames transmission only, RIP frames reception only or both transmission and reception of RIP frames.
OBJECT-TYPE    
  INTEGER duplex(1), tx-only(2), rx-only(3), not-applicable(254), not-available(255)  

ifwanIpRipAuthType 1.3.6.1.4.1.727.7.2.2.2.1.119
Enable or disable password authentication for the interface. If you select Simple Password, the password will be included in the sent RIP frames. The received frames containing authentication will be accepted only if the password is valid.
OBJECT-TYPE    
  INTEGER none(1), simple(2), not-applicable(254), not-available(255)  

ifwanIpRipPassword 1.3.6.1.4.1.727.7.2.2.2.1.120
This configured data allows the authentication procedure to generate and/or verify the authentication field in the RIP header. This value again must be the same for each interface on each side of the link.
OBJECT-TYPE    
  DisplayString  

ifwanPppSilent 1.3.6.1.4.1.727.7.2.2.2.1.121
This parameter defines how this port participates in the configuration negotiation process. When a PPP port is Silent, it waits for a Configure-Request packet from the remote peer. Use WAIT FOR REQUEST to configure the port in this way. The port must receive a request before it can negotiate a connection. When a port is not Silent, it is actively trying to initialize the connection with the remote peer. Use the SEND REQUEST setting. The port will send Configure-Request packets in a timeout/retry sequence until the remote peer replies, at which point the two peers can negotiate the connection.
OBJECT-TYPE    
  INTEGER send-request(1), wait-for-request(2), not-applicable(254), not-available(255)  

ifwanPppConfigRestartTimer 1.3.6.1.4.1.727.7.2.2.2.1.122
This parameter defines the duration, in seconds, of the Restart timer, which is started when a Configure-Request or Terminate-Request packet is transmitted. If the timer expires a timeout occurs, followed by retransmission of the packet. Configure the Configuration Restart Timer parameter based on the speed of the link. The default value, 3 seconds, is designed for low-speed lines (from 2400 to 9600 bps) and links having a high switching latency, such as telephone lines. For higher speed links or links with low switching latency the retransmission time is reduced, so the Retry Period should be reduced also. For example, round trip transmission times for modems at 14,400 bps are in the range of 160 to 600 milliseconds. A value of 1 second for the Configuration Restart Timer would be appropriate.
OBJECT-TYPE    
  INTEGER 0..255  

ifwanPppConfigRetries 1.3.6.1.4.1.727.7.2.2.2.1.123
This parameter is a restart counter for Configure-Requests. It defines the maximum number of successive retry periods that can elapse when the port attempts to send a Configure-Request packet to the remote peer. The port counts the number of retry periods that elapse before receiving a Configure-Ack, Configure-Nak or Configure-Reject from the peer, until it assumes that the peer is unable to respond. The values 0 to 254 set a finite number of retry periods. Use the value 255 to allow the port to send a Configure-Request packet an unlimited number of times.
OBJECT-TYPE    
  INTEGER 0..255  

ifwanPppNegociateLocalMru 1.3.6.1.4.1.727.7.2.2.2.1.124
This parameter enables the negotiation of another MRU than the default MRU value (1500 bytes). The MRU is used when sending parameter values between peers to negotiate the connection. In particular, it specifies the maximum number of bytes in the Information and Padding fields of the PPP encapsulation frame. If you set this parameter to YES, you must also configure the Negotiated Local MRU parameter.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanPppLocalMru 1.3.6.1.4.1.727.7.2.2.2.1.125
This parameter determines the size of the MRU that the local port offers (if greater than the default value) or requests (if less than the default value) for use by the peer. The MRU specifies the maximum number of bytes allowed in the Information and Padding fields of the PPP encapsulation frame.
OBJECT-TYPE    
  INTEGER 0..3000  

ifwanPppNegociatePeerMru 1.3.6.1.4.1.727.7.2.2.2.1.126
This parameter determines whether the port will consider either an offer for a larger MRU value or a request for a smaller one. Set this parameter to YES to allow the port to consider an MRU offer or request from the peer. Set it to NO (the default value) to reject it. If you set this parameter to YES, you must also configure the Peer's MRU parameter.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanPppPeerMruUpTo 1.3.6.1.4.1.727.7.2.2.2.1.127
This parameter determines up to what limit above the default MRU value the local port will set its MRU in response to an offer or request from the peer.
OBJECT-TYPE    
  INTEGER 0..3000  

ifwanPppNegociateAccm 1.3.6.1.4.1.727.7.2.2.2.1.128
This parameter determines whether the port will inform the remote peer that it can enter into Asynchronous Control Character Map (ACCM) negotiation. This option provides a way to negotiate the use of control character mapping on asynchronous links. By default, PPP maps all control characters into an appropriate two-character sequence. This is usually not necessary. The cleartrac uses the ACCM negotiation option to inform the remote end which control characters must remain mapped, and which ones do not need to remain mapped when the remote end sends them. Set this parameter to YES to permit ACCM negotiation. Set it to NO (the default value) to disallow this negotiation process. If you set this parameter to YES, you must also configure the Requested ACCM Characters parameter.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanPppRequestedAccmChar 1.3.6.1.4.1.727.7.2.2.2.1.129
This parameter determines the exact characters of the Asynchronous Control Character Map that are requested from the remote peer. The Async-Control-Character-Map field is 4 bytes long. It encoded such that each numbered bit corresponds to the ASCII control character of the same value. If a bit is cleared to zero, then the corresponding ASCII control character must remain mapped. For example, if bit 19 is set to zero, then ASCII control character 19 (CTRL-S) will not be changed during transmission.
OBJECT-TYPE    
  STRING Size(4)  

ifwanPppAcceptAccmPeer 1.3.6.1.4.1.727.7.2.2.2.1.130
This parameter determines whether the port will accept a request from the remote peer to enter into Asynchronous Control Character Map (ACCM) negotiation. Set this parameter to YES to accept the peer's request. Set it to NO (the default value) to reject the request for ACCM negotiation. If you set this parameter to YES, you must also configure the Acceptable ACCM Characters parameter.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanPppAcceptableAccmChar 1.3.6.1.4.1.727.7.2.2.2.1.131
This parameter determines the exact characters of the Asynchronous Control Character Map that will be sent to the remote peer. The Async-Control-Character-Map field is 4 bytes, encoded such that each numbered bit corresponds to the ASCII control character of the same value. If a bit is cleared to zero, then the corresponding ASCII control character must remain mapped. For example, if bit 19 is set to zero, then ASCII control character 19 (CTRL-S) may be sent without change.
OBJECT-TYPE    
  STRING Size(4)  

ifwanPppRequestMagicNum 1.3.6.1.4.1.727.7.2.2.2.1.132
This parameter determines whether the port will request the Magic Number from the remote peer. The Magic Number is a 4-byte field that aids in the detection of link loopback conditions and other data link layer anomalies. Set this parameter to YES (the default value) to request the peer's Magic Number. Set it to NO to disallow a Magic Number request.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanPppAcceptMagicNum 1.3.6.1.4.1.727.7.2.2.2.1.133
This parameter determines whether the port will accept a request from the remote peer to send the local Magic Number. Set this parameter to YES (the default value) to accept the peer's Magic Number request. Set it to NO to reject the request.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanPppAcceptOldIpAddNeg 1.3.6.1.4.1.727.7.2.2.2.1.134
This parameter determines whether the port will accept a request from the remote peer to negotiate old IP-Addresses. Set this parameter to YES to accept the peer's IP-Addresses Negotiation request. The port will enter into an obsolete IP address negotiation with the peer. Set it to NO (the default value) to reject this configuration option.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanPppNegociateIpAddress 1.3.6.1.4.1.727.7.2.2.2.1.135
This parameter enables the negotiation of an IP Address with the remote peer. Set this parameter to YES (the default value) to allow the port to request and accept an IP Address. Set it to NO to disallow IP address negotiation.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanPppAcceptIpAddress 1.3.6.1.4.1.727.7.2.2.2.1.136
This parameter determines whether the port will accept a request from the remote peer to send an IP Address. Set this parameter to YES ( the default value) to accept the peer's request for the local IP Address. Set it to NO to reject the request.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanPppRemoteIpAddress 1.3.6.1.4.1.727.7.2.2.2.1.137
This parameter defines the IP-Address to be sent to the remote peer during negotiation of the connection. The IP-Address is specific to a particular PPP session. It is a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte, for example 128.128.128.122. When this parameter is set to 000.000.000.000, no IP-Address is defined.
OBJECT-TYPE    
  IpAddress  

ifwanPppRemoteSubnetMask 1.3.6.1.4.1.727.7.2.2.2.1.138
Subnet mask associated with the Remote IP address. It is configured like the IP address: a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. The subnet mask identifies which bits of the IP address correspond to the physical network, and which bits correspond to host identifiers.
OBJECT-TYPE    
  IpAddress  

ifwanHighPriorityTransparentClass 1.3.6.1.4.1.727.7.2.2.2.1.139
High priority transparent class.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanTransparentClassNumber 1.3.6.1.4.1.727.7.2.2.2.1.140
The transparent priority class for voice. Classes are defined according to bandwidth weight.
OBJECT-TYPE    
  INTEGER 1..8  

ifwanChannelCompressed 1.3.6.1.4.1.727.7.2.2.2.1.141
Channel compressed.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifwanSfType 1.3.6.1.4.1.727.7.2.2.2.1.142
Specify the type of Skyframe port configured. It can be a Modulator, Demodulator, Expansion or Aggregate.
OBJECT-TYPE    
  INTEGER demodulator(1), modulator(2), expansion(3), agregate(4), not-applicable(254), not-available(255)  

ifwanSfMode 1.3.6.1.4.1.727.7.2.2.2.1.143
Enable/disable the data transmission/reception on the port.
OBJECT-TYPE    
  INTEGER inactive(1), active(2), not-applicable(254), not-available(255)  

ifwanSfCarrierId 1.3.6.1.4.1.727.7.2.2.2.1.144
Identifier of a physical port in a Skyframe system.
OBJECT-TYPE    
  INTEGER  

ifvceNumber 1.3.6.1.4.1.727.7.2.18.1
The number of voice interfaces present on this system.
OBJECT-TYPE    
  INTEGER  

ifvceTable 1.3.6.1.4.1.727.7.2.18.2
A list of interface entries. The number of entries is given by the value of ifvceNumber.
OBJECT-TYPE    
  SEQUENCE OF  
    IfvceEntry

ifvceEntry 1.3.6.1.4.1.727.7.2.18.2.1
This table contains the principal configurable parameters which are used for a particular voice interface.
OBJECT-TYPE    
  IfvceEntry  

ifvceIndex 1.3.6.1.4.1.727.7.2.18.2.1.1
A unique value for each voice interface.
OBJECT-TYPE    
  INTEGER  

ifvceDesc 1.3.6.1.4.1.727.7.2.18.2.1.2
A textual string containing information about a specific interface.
OBJECT-TYPE    
  DisplayString  

ifvceProtocol 1.3.6.1.4.1.727.7.2.18.2.1.3
Operating protocol for the NetVoice port. Enter ACELP 8 kbs, ACELP 4.8 kbs when you want to use the port for voice/fax transmissions. Select the OFF value when the port is not used.
OBJECT-TYPE    
  INTEGER off(1), acelp-8-kbs(21), acelp-4-8-kbs(22), pcm64k(23), adpcm32k(24), atc16k(26), acelp-cn(30), not-applicable(254), not-available(255)  

ifvceInterface 1.3.6.1.4.1.727.7.2.18.2.1.4
fxs: Used when connecting to a POTS line or fx0 unit. e-and-m: Used when connecting to the trunk side of a PBX. fx0: Used when connecting to a CO or the station side of a PBX.
OBJECT-TYPE    
  INTEGER fxs(1), fx0(2), e-and-m(3), ac15(4), not-applicable(254), not-available(255)  

ifvceRemotePort 1.3.6.1.4.1.727.7.2.18.2.1.5
Specifies the port number on the remote unit for setting up predefined line activation. Select the number of the port connected to the device you want to reach.
OBJECT-TYPE    
  INTEGER 1..899  

ifvceActivationType 1.3.6.1.4.1.727.7.2.18.2.1.6
For each cleartrac voice port, voice/fax line activation can be configured according to one of the following activation types.
OBJECT-TYPE    
  INTEGER predefined(1), switched(2), autodial(3), broadcast(4), not-applicable(254), not-available(255)  

ifvceRemoteUnit 1.3.6.1.4.1.727.7.2.18.2.1.7
Specifies the unit name of the NetVoice card at the remote site, for setting up predefined line activation.
OBJECT-TYPE    
  DisplayString  

ifvceHuntGroup 1.3.6.1.4.1.727.7.2.18.2.1.8
When line activation is defined as switched, this parameter permits hunting more than one port to place an incoming call.
OBJECT-TYPE    
  INTEGER no(1), a(2), b(3), not-applicable(254), not-available(255)  

ifvceToneDetectRegen-s 1.3.6.1.4.1.727.7.2.18.2.1.9
This parameter specifies the number of seconds during which Tone tones will be detected and regenerated.
OBJECT-TYPE    
  INTEGER 0..256  

ifvcePulseMakeBreak-ms 1.3.6.1.4.1.727.7.2.18.2.1.10
This parameter specifies the duration, in milliseconds, of the contact(or make) for each digit that is dialed using rotary type dialing.
OBJECT-TYPE    
  INTEGER 20..80  

ifvceToneOn-ms 1.3.6.1.4.1.727.7.2.18.2.1.11
This parameter specifies the duration, in milliseconds, of the tone used to produce a single Tone digit.
OBJECT-TYPE    
  INTEGER 30..1000  

ifvceToneOff-ms 1.3.6.1.4.1.727.7.2.18.2.1.12
This parameter specifies the duration, in milliseconds, of the silence between Tone tones in a dial digit string.
OBJECT-TYPE    
  INTEGER 30..1000  

ifvceSilenceSuppress 1.3.6.1.4.1.727.7.2.18.2.1.13
This parameter specifies the degree to which periods of silence will be suppressed and reduced during transmission. A higher Silence Suppression level increases the attenuation of the line, lowers background noise and reduces overall bandwidth use. ONLY FOR EXPANSION CARDS OTHER THAN DVC
OBJECT-TYPE    
  INTEGER 4..20  

ifvceDVCSilenceSuppress 1.3.6.1.4.1.727.7.2.18.2.1.33
This parameter specifies the degree to which periods of silence will be suppressed and reduced during transmission. A higher Silence Suppression level increases the attenuation of the line, lowers background noise and reduces overall bandwidth use. ONLY FOR DVC CARDS
OBJECT-TYPE    
  INTEGER 1..5  

ifvceSignaling 1.3.6.1.4.1.727.7.2.18.2.1.14
The signaling protocol of this port.
OBJECT-TYPE    
  INTEGER e-and-m-4w-imm-start(1), e-and-m-2W-imm-start(2), loop-start(3), ac15-a(4), ac15-c(6), e-and-m-4w-timed-e(10), e-and-m-2W-timed-e(11), e-and-m-4W-wink-start(12), e-and-m-2W-wink-start(13), e-and-m-4W-delay-dial(14), e-and-m-2W-delay-dial(15), e-and-m-4W-colisee(17), e-and-m-2W-colisee(18), imm-start(21), r2(22), fxo(23), fxs(24), gnd-fxo(25), gnd-fxs(26), plar(27), poi(28), wink-start(32), ab00(30), not-applicable(254), not-available(255)  

ifvceLocalInbound 1.3.6.1.4.1.727.7.2.18.2.1.16
This parameter specifies the local voice level into the port, measured in 1 db increments. ONLY FOR CARDS OTHER THAN DVC
OBJECT-TYPE    
  INTEGER db-22(1), db-21(2), db-20(3), db-19(4), db-18(5), db-17(6), db-16(7), db-15(8), db-14(9), db-13(10), db-12(11), db-11(12), db-10(13), db-9(14), db-8(15), db-7(16), db-6(17), db-5(18), db-4(19), db-3(20), db-2(21), db-1(22), db0(23), db1(24), db2(25), db3(26), db4(27), db5(28), db6(29), db7(30), not-applicable(254), not-available(255)  

ifvceLocalOutbound 1.3.6.1.4.1.727.7.2.18.2.1.17
This parameter specifies the local voice level out of the port, measured in 1 db increments. ONLY FOR CARDS OTHER THAN DVC
OBJECT-TYPE    
  INTEGER db-22(1), db-21(2), db-20(3), db-19(4), db-18(5), db-17(6), db-16(7), db-15(8), db-14(9), db-13(10), db-12(11), db-11(12), db-10(13), db-9(14), db-8(15), db-7(16), db-6(17), db-5(18), db-4(19), db-3(20), db-2(21), db-1(22), db0(23), db1(24), db2(25), db3(26), db4(27), db5(28), db6(29), db7(30), not-applicable(254), not-available(255)  

ifvceDVCLocalInbound 1.3.6.1.4.1.727.7.2.18.2.1.34
This parameter specifies the local voice level into the port, measured in 1 db increments. ONLY FOR DVC CARDS
OBJECT-TYPE    
  INTEGER db-12(9), db-11(10), db-10(11), db-9(12), db-8(13), db-7(14), db-6(15), db-5(16), db-4(17), db-3(18), db-2(19), db-1(20), db0(21), db1(22), db2(23), db3(24), db4(25), db5(26), db6(27), not-applicable(254), not-available(255)  

ifvceDVCLocalOutbound 1.3.6.1.4.1.727.7.2.18.2.1.35
This parameter specifies the local voice level out of the port, measured in 1 db increments. ONLY FOR DVC CARDS
OBJECT-TYPE    
  INTEGER db-12(9), db-11(10), db-10(11), db-9(12), db-8(13), db-7(14), db-6(15), db-5(16), db-4(17), db-3(18), db-2(19), db-1(20), db0(21), db1(22), db2(23), db3(24), db4(25), db5(26), db6(27), not-applicable(254), not-available(255)  

ifvceFaxModemRelay 1.3.6.1.4.1.727.7.2.18.2.1.18
This parameter enables or disables handling of fax or modem calls on this unit's voice channel.
OBJECT-TYPE    
  INTEGER none(1), fax(2), both(3), not-applicable(254), not-available(255)  

ifvceMaxFaxModemRate 1.3.6.1.4.1.727.7.2.18.2.1.44
This parameter enables or disables handling of fax or modem calls on this unit's voice channel.
OBJECT-TYPE    
  INTEGER rate-14400(1), rate-12000(2), rate-9600(3), rate-7200(4), rate-4800(5), not-applicable(254), not-available(255)  

ifvceFxoTimeout-s 1.3.6.1.4.1.727.7.2.18.2.1.19
This parameter determines the maximum amount of time, in seconds, that the local port will wait for a fax transmission to begin.
OBJECT-TYPE    
  INTEGER 1..99  

ifvceTeTimer-s 1.3.6.1.4.1.727.7.2.18.2.1.20
This parameter determines the delay, in seconds, between M-lead and E-lead activation when the starting method is timed e-and-m.
OBJECT-TYPE    
  INTEGER 0..255  

ifvceFwdDigits 1.3.6.1.4.1.727.7.2.18.2.1.21
This parameter specifies which dial digits (if any) should be forwarded to the remote unit. When set to 0, no dial digits are forwarded to the destination device when a call is initiated on this channel. When set to a non-zero value, the specified number of dial digits are forwarded.
OBJECT-TYPE    
  INTEGER none(1), all(2), ext(3), not-applicable(254), not-available(255)  

ifvceFwdType 1.3.6.1.4.1.727.7.2.18.2.1.22
This parameter specifies how the dial digits are sent to the remote unit for forwarding to the attached device such as a PBX. It can do it using pulse dial or Tone.
OBJECT-TYPE    
  INTEGER tone(1), pulse(2), not-applicable(254), not-available(255)  

ifvceFwdDelay-ms 1.3.6.1.4.1.727.7.2.18.2.1.23
This parameter specifies the length, in milliseconds, of a pause that precedes the forwarded dial digit string. The value entered with a SET is rounded down to the nearest multiple of 250 ms
OBJECT-TYPE    
  INTEGER 0..10000  

ifvceDelDigits 1.3.6.1.4.1.727.7.2.18.2.1.24
This parameter specifies the number of leading dial digits (if any) that will be deleted from a dial string before it is forwarded to the attached voice equipment. When set to 0, no dial digits are deleted.
OBJECT-TYPE    
  INTEGER 0..4  

ifvceExtNumber 1.3.6.1.4.1.727.7.2.18.2.1.25
This parameter specifies the extension number for the end device attached to this voice port.
OBJECT-TYPE    
  DisplayString  

ifvceLinkDwnBusy 1.3.6.1.4.1.727.7.2.18.2.1.27
Used by SDM-9400 and V410 VFC03 cards and by the SDM-9350 and V352 voice ports for versions 7.1.0 and higher. Used only for DVC cards for versions 7.0.3 and lower. See also ifvceAnalogLinkDwnBusy for versions 7.0.3 and lower.
OBJECT-TYPE    
  INTEGER no(1), yes(2), broadcast(3), not-applicable(254), not-available(255)  

ifvceToneType 1.3.6.1.4.1.727.7.2.18.2.1.28
This parameter specifies the kind of multi-frequency tone that will be detected on this port.
OBJECT-TYPE    
  INTEGER dtmf(0), mf(1), r2(2), not-applicable(254), not-available(255)  

ifvceRate8kx1 1.3.6.1.4.1.727.7.2.18.2.1.29
This parameter enables fallback to 8 Kbps with single buffering.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifvceRate8kx2 1.3.6.1.4.1.727.7.2.18.2.1.30
This parameter enables fallback to 8 Kbps with double buffering.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifvceRate5k8x1 1.3.6.1.4.1.727.7.2.18.2.1.31
This parameter enables fallback to 5.8 Kbps with single buffering.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifvceRate5k8x2 1.3.6.1.4.1.727.7.2.18.2.1.32
This parameter enables fallback to 5.8 Kbps with double buffering.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifvceBroadcastDir 1.3.6.1.4.1.727.7.2.18.2.1.36
When line activation is broadcast (Activation Type parameter set to BROADCAST), this parameter is used to specify whether the voice port will transmit(TX) or receive (RX) broadcast messages.
OBJECT-TYPE    
  INTEGER tX(1), rX(2), not-applicable(254), not-available(255)  

ifvceBroadcastPvc 1.3.6.1.4.1.727.7.2.18.2.1.37
This parameter specifies which PVC will be used for transmitting (on the root) or receiving (on leaves) the broadcast frames.
OBJECT-TYPE    
  INTEGER 0..300  

ifvceAnalogLinkDwnBusy 1.3.6.1.4.1.727.7.2.18.2.1.38
Used by SDM-9400 and V410 VFC03 cards and by the SDM-9350 and V352 voice ports for versions 7.0.3 and lower. See ifvceLinkDwnBusy for version 7.1.0 and higher and for DVC cards.
OBJECT-TYPE    
  INTEGER no(1), yes(2), broadcast(3), not-applicable(254), not-available(255)  

ifvceSpeedDialNum 1.3.6.1.4.1.727.7.2.18.2.1.39
Specifies the Speed Dial Number to be dialed when a off-hook occurs on a port configured with Autodial activation type.
OBJECT-TYPE    
  DisplayString  

ifvceR2ExtendedDigitSrc 1.3.6.1.4.1.727.7.2.18.2.1.40
No longer supported by the NP Agent 7.1.0 and higher
OBJECT-TYPE    
  INTEGER map(1), user(2), not-applicable(254), not-available(255)  

ifvceR2Group2Digit 1.3.6.1.4.1.727.7.2.18.2.1.41
This parameter defines a Group 2 Digit that is output when dialing out.
OBJECT-TYPE    
  INTEGER 0..15  

ifvceR2CompleteDigit 1.3.6.1.4.1.727.7.2.18.2.1.42
This parameter defines the digit that is output when dialing is complete.
OBJECT-TYPE    
  INTEGER 1..15  

ifvceR2BusyDigit 1.3.6.1.4.1.727.7.2.18.2.1.43
This parameter defines the digit that is output to indicate that the destination is busy.
OBJECT-TYPE    
  INTEGER 1..15  

ifvceRate8kx3 1.3.6.1.4.1.727.7.2.18.2.1.45
This parameter enables fallback to 8 Kbps with triple buffering.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifvceRate6kx1 1.3.6.1.4.1.727.7.2.18.2.1.46
This parameter enables fallback to 6 Kbps with single buffering.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifvceRate6kx2 1.3.6.1.4.1.727.7.2.18.2.1.47
This parameter enables fallback to 6 Kbps with double buffering.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(254), not-available(255)  

ifvceRate6kx3 1.3.6.1.4.1.727.7.2.18.2.1.48