CISCOSB-BRIDGEMIBOBJECTS-MIB

File: CISCOSB-BRIDGEMIBOBJECTS-MIB.mib (66053 bytes)

Imported modules

CISCOSB-MIB SNMPv2-SMI SNMPv2-TC
RFC1155-SMI BRIDGE-MIB IF-MIB
Q-BRIDGE-MIB SNMP-FRAMEWORK-MIB

Imported symbols

switch001 OBJECT-TYPE MODULE-IDENTITY
TimeTicks Counter32 TruthValue
DisplayString RowStatus Counter
BridgeId Timeout dot1dBasePort
dot1dStpPort InterfaceIndex ifIndex
PortList SnmpAdminString

Defined Types

VlanList1  
Each octet within this value specifies a set of eight vlans, with the first octet specifying vlan 1 through 8, the second octet specifying vlan 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered vlan, and the least significant bit represents the highest numbered vlan. Thus, each vlan of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is included in the set of vlans; the vlan is not included if its bit has a value of '0'. VlanList1 represent vlans 1-1024
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..128)  

VlanList2  
As VlanList1 but represent vlans 1025-2048
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..128)  

VlanList3  
As VlanList1 but represent vlans 2049-3072
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..128)  

VlanList4  
As VlanList1 but represent vlans 3073-4094
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..128)  

Rldot1dPriorityPortGroupEntry  
SEQUENCE    
  rldot1dPriorityPortGroupNumber INTEGER

Rldot1dStpVlanEntry  
SEQUENCE    
  rldot1dStpVlan INTEGER
  rldot1dStpVlanEnable TruthValue
  rldot1dStpTimeSinceTopologyChange TimeTicks
  rldot1dStpTopChanges Counter
  rldot1dStpDesignatedRoot BridgeId
  rldot1dStpRootCost INTEGER
  rldot1dStpRootPort INTEGER
  rldot1dStpMaxAge Timeout
  rldot1dStpHelloTime Timeout
  rldot1dStpHoldTime INTEGER
  rldot1dStpForwardDelay Timeout

Rldot1dStpVlanPortEntry  
SEQUENCE    
  rldot1dStpVlanPortVlan INTEGER
  rldot1dStpVlanPortPort INTEGER
  rldot1dStpVlanPortPriority INTEGER
  rldot1dStpVlanPortState INTEGER
  rldot1dStpVlanPortEnable INTEGER
  rldot1dStpVlanPortPathCost INTEGER
  rldot1dStpVlanPortDesignatedRoot BridgeId
  rldot1dStpVlanPortDesignatedCost INTEGER
  rldot1dStpVlanPortDesignatedBridge BridgeId
  rldot1dStpVlanPortDesignatedPort OCTET STRING
  rldot1dStpVlanPortForwardTransitions Counter

Rldot1dStpPortEntry  
SEQUENCE    
  rldot1dStpPortPort INTEGER
  rldot1dStpPortDampEnable TruthValue
  rldot1dStpPortDampStable TruthValue
  rldot1dStpPortFilterBpdu INTEGER
  rldot1dStpPortBpduSent Counter32
  rldot1dStpPortBpduReceived Counter32
  rldot1dStpPortRole INTEGER
  rldot1dStpBpduType INTEGER
  rldot1dStpPortRestrictedRole TruthValue
  rldot1dStpPortAutoEdgePort TruthValue
  rldot1dStpPortLoopback TruthValue
  rldot1dStpPortBpduOperStatus INTEGER

Rldot1dStpPortBpduGuardEntry  
SEQUENCE    
  rldot1dStpPortBpduGuardEnable TruthValue

Rldot1dStpSeparatedBridgesEntry  
SEQUENCE    
  rldot1dStpSeparatedBridgesPortEnable TruthValue

Rldot1dStpDisabledPortStateEntry  
SEQUENCE    
  rldot1dStpDisabledPortState INTEGER

Rldot1wRStpVlanEdgePortEntry  
SEQUENCE    
  rldot1wRStpVlanEdgePortVlan INTEGER
  rldot1wRStpVlanEdgePortPort INTEGER
  rldot1wRStpEdgePortStatus TruthValue

Rldot1wRStpForceVersionEntry  
SEQUENCE    
  rldot1wRStpForceVersionVlan INTEGER
  rldot1wRStpForceVersionState INTEGER

Rldot1pPriorityMapEntry  
SEQUENCE    
  rldot1pPriorityMapName DisplayString
  rldot1pPriorityMapPriority OCTET STRING
  rldot1pPriorityMapPort PortList
  rldot1pPriorityMapPortList PortList
  rldot1pPriorityMapStatus RowStatus

Rldot1sMstpInstanceEntry  
SEQUENCE    
  rldot1sMstpInstanceId INTEGER
  rldot1sMstpInstanceEnable TruthValue
  rldot1sMstpInstanceTimeSinceTopologyChange TimeTicks
  rldot1sMstpInstanceTopChanges Counter
  rldot1sMstpInstanceDesignatedRoot BridgeId
  rldot1sMstpInstanceRootCost INTEGER
  rldot1sMstpInstanceRootPort INTEGER
  rldot1sMstpInstanceMaxAge Timeout
  rldot1sMstpInstanceHelloTime Timeout
  rldot1sMstpInstanceHoldTime INTEGER
  rldot1sMstpInstanceForwardDelay Timeout
  rldot1sMstpInstancePriority INTEGER
  rldot1sMstpInstanceRemainingHopes INTEGER

Rldot1sMstpInstancePortEntry  
SEQUENCE    
  rldot1sMstpInstancePortMstiId INTEGER
  rldot1sMstpInstancePortPort INTEGER
  rldot1sMstpInstancePortPriority INTEGER
  rldot1sMstpInstancePortState INTEGER
  rldot1sMstpInstancePortEnable INTEGER
  rldot1sMstpInstancePortPathCost INTEGER
  rldot1sMstpInstancePortDesignatedRoot BridgeId
  rldot1sMstpInstancePortDesignatedCost INTEGER
  rldot1sMstpInstancePortDesignatedBridge BridgeId
  rldot1sMstpInstancePortDesignatedPort OCTET STRING
  rldot1sMstpInstancePortForwardTransitions Counter
  rldot1sMStpInstancePortAdminPathCost INTEGER
  rldot1sMStpInstancePortRole INTEGER

Rldot1sMstpVlanEntry  
SEQUENCE    
  rldot1sMstpVlan INTEGER
  rldot1sMstpGroup INTEGER
  rldot1sMstpPendingGroup INTEGER

Rldot1sMstpExtPortEntry  
SEQUENCE    
  rldot1sMstpExtPortPort INTEGER
  rldot1sMstpExtPortInternalOperPathCost INTEGER
  rldot1sMstpExtPortDesignatedRegionalRoot BridgeId
  rldot1sMstpExtPortDesignatedRegionalCost INTEGER
  rldot1sMstpExtPortBoundary TruthValue
  rldot1sMstpExtPortInternalAdminPathCost INTEGER

Rldot1sMstpInstanceVlanEntry  
SEQUENCE    
  rldot1sMstpInstanceVlanId INTEGER
  rldot1sMstpInstanceVlanId1To1024 VlanList1
  rldot1sMstpInstanceVlanId1025To2048 VlanList2
  rldot1sMstpInstanceVlanId2049To3072 VlanList3
  rldot1sMstpInstanceVlanId3073To4094 VlanList4

Defined Values

rlpBridgeMIBObjects 1.3.6.1.4.1.9.6.1.101.57
This private MIB module defines bridge MIB objects private MIBs.
MODULE-IDENTITY    

rldot1dPriority 1.3.6.1.4.1.9.6.1.101.57.1
OBJECT IDENTIFIER    

rldot1dPriorityMibVersion 1.3.6.1.4.1.9.6.1.101.57.1.1
MIB's version, the current version is 1.
OBJECT-TYPE    
  INTEGER  

rldot1dPriorityPortGroupTable 1.3.6.1.4.1.9.6.1.101.57.1.2
A list of PortGroupNumber for each port.
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1dPriorityPortGroupEntry

rldot1dPriorityPortGroupEntry 1.3.6.1.4.1.9.6.1.101.57.1.2.1
All ports belonging to a same group have the same User Priority to Traffic Class mapping.
OBJECT-TYPE    
  Rldot1dPriorityPortGroupEntry  

rldot1dPriorityPortGroupNumber 1.3.6.1.4.1.9.6.1.101.57.1.2.1.1
A group, that port belongs to. All ports belonging to a same group have the same User Priority to Traffic Class mapping.
OBJECT-TYPE    
  INTEGER  

rldot1dStp 1.3.6.1.4.1.9.6.1.101.57.2
OBJECT IDENTIFIER    

rldot1dStpMibVersion 1.3.6.1.4.1.9.6.1.101.57.2.1
MIB's version, the current version is 2.
OBJECT-TYPE    
  INTEGER  

rldot1dStpType 1.3.6.1.4.1.9.6.1.101.57.2.2
Specifies whether the device supports Spanning Tree per device, or per group.
OBJECT-TYPE    
  INTEGER perDevice(1), mstp(4)  

rldot1dStpEnable 1.3.6.1.4.1.9.6.1.101.57.2.3
Enable / Disable spanning tree. When working in per vlan mode enable / disable STP per all vlans.
OBJECT-TYPE    
  TruthValue  

rldot1dStpPortMustBelongToVlan 1.3.6.1.4.1.9.6.1.101.57.2.4
Specifies whether a port must belong to a VLAN in order to participate in the STP.
OBJECT-TYPE    
  TruthValue  

rldot1dStpExtendedPortNumberFormat 1.3.6.1.4.1.9.6.1.101.57.2.5
Specifies whether the STP uses the extended port fnumber format.
OBJECT-TYPE    
  TruthValue  

rldot1dStpVlanTable 1.3.6.1.4.1.9.6.1.101.57.2.6
A table that contains vlan-specific information for the Spanning Tree Protocol.
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1dStpVlanEntry

rldot1dStpVlanEntry 1.3.6.1.4.1.9.6.1.101.57.2.6.1
A list of information maintained by every Vlan about the Spanning Tree Protocol state for that Vlan.
OBJECT-TYPE    
  Rldot1dStpVlanEntry  

rldot1dStpVlan 1.3.6.1.4.1.9.6.1.101.57.2.6.1.1
The Vlan index.
OBJECT-TYPE    
  INTEGER  

rldot1dStpVlanEnable 1.3.6.1.4.1.9.6.1.101.57.2.6.1.2
Specifies whether this vlan is STP enable or disable
OBJECT-TYPE    
  TruthValue  

rldot1dStpTimeSinceTopologyChange 1.3.6.1.4.1.9.6.1.101.57.2.6.1.3
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
OBJECT-TYPE    
  TimeTicks  

rldot1dStpTopChanges 1.3.6.1.4.1.9.6.1.101.57.2.6.1.4
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
OBJECT-TYPE    
  Counter  

rldot1dStpDesignatedRoot 1.3.6.1.4.1.9.6.1.101.57.2.6.1.5
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
OBJECT-TYPE    
  BridgeId  

rldot1dStpRootCost 1.3.6.1.4.1.9.6.1.101.57.2.6.1.6
The cost of the path to the root as seen from this bridge.
OBJECT-TYPE    
  INTEGER  

rldot1dStpRootPort 1.3.6.1.4.1.9.6.1.101.57.2.6.1.7
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
OBJECT-TYPE    
  INTEGER  

rldot1dStpMaxAge 1.3.6.1.4.1.9.6.1.101.57.2.6.1.8
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
OBJECT-TYPE    
  Timeout  

rldot1dStpHelloTime 1.3.6.1.4.1.9.6.1.101.57.2.6.1.9
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
OBJECT-TYPE    
  Timeout  

rldot1dStpHoldTime 1.3.6.1.4.1.9.6.1.101.57.2.6.1.10
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
OBJECT-TYPE    
  INTEGER  

rldot1dStpForwardDelay 1.3.6.1.4.1.9.6.1.101.57.2.6.1.11
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
OBJECT-TYPE    
  Timeout  

rldot1dStpVlanPortTable 1.3.6.1.4.1.9.6.1.101.57.2.7
A table that contains pair specific information for the Spanning Tree Protocol.
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1dStpVlanPortEntry

rldot1dStpVlanPortEntry 1.3.6.1.4.1.9.6.1.101.57.2.7.1
A list of information maintained by every pair about the Spanning Tree Protocol state for that pair.
OBJECT-TYPE    
  Rldot1dStpVlanPortEntry  

rldot1dStpVlanPortVlan 1.3.6.1.4.1.9.6.1.101.57.2.7.1.1
The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information.
OBJECT-TYPE    
  INTEGER 1..4095  

rldot1dStpVlanPortPort 1.3.6.1.4.1.9.6.1.101.57.2.7.1.2
The port number of the port for which this entry contains Spanning Tree Protocol management information.
OBJECT-TYPE    
  INTEGER 1..4096  

rldot1dStpVlanPortPriority 1.3.6.1.4.1.9.6.1.101.57.2.7.1.3
The value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of rldot1dStpVlanPort.
OBJECT-TYPE    
  INTEGER 0..255  

rldot1dStpVlanPortState 1.3.6.1.4.1.9.6.1.101.57.2.7.1.4
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpVlanPortEnable), this object will have a value of disabled(1).
OBJECT-TYPE    
  INTEGER disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)  

rldot1dStpVlanPortEnable 1.3.6.1.4.1.9.6.1.101.57.2.7.1.5
The enabled/disabled status of the port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

rldot1dStpVlanPortPathCost 1.3.6.1.4.1.9.6.1.101.57.2.7.1.6
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
OBJECT-TYPE    
  INTEGER 1..65535  

rldot1dStpVlanPortDesignatedRoot 1.3.6.1.4.1.9.6.1.101.57.2.7.1.7
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
OBJECT-TYPE    
  BridgeId  

rldot1dStpVlanPortDesignatedCost 1.3.6.1.4.1.9.6.1.101.57.2.7.1.8
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OBJECT-TYPE    
  INTEGER  

rldot1dStpVlanPortDesignatedBridge 1.3.6.1.4.1.9.6.1.101.57.2.7.1.9
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
OBJECT-TYPE    
  BridgeId  

rldot1dStpVlanPortDesignatedPort 1.3.6.1.4.1.9.6.1.101.57.2.7.1.10
The Port Identifier of the port on the Designated Bridge for this port's segment.
OBJECT-TYPE    
  OCTET STRING Size(2)  

rldot1dStpVlanPortForwardTransitions 1.3.6.1.4.1.9.6.1.101.57.2.7.1.11
The number of times this port has transitioned from the Learning state to the Forwarding state.
OBJECT-TYPE    
  Counter  

rldot1dStpTrapVariable 1.3.6.1.4.1.9.6.1.101.57.2.8
OBJECT IDENTIFIER    

rldot1dStpTrapVrblifIndex 1.3.6.1.4.1.9.6.1.101.57.2.8.1
The ifIndex of port which STP status was changed
OBJECT-TYPE    
  InterfaceIndex  

rldot1dStpTrapVrblVID 1.3.6.1.4.1.9.6.1.101.57.2.8.2
The VID of VLAN to which the port belongs which STP status was changed
OBJECT-TYPE    
  INTEGER  

rldot1dStpTypeAfterReset 1.3.6.1.4.1.9.6.1.101.57.2.9
New mode of spaning tree supported by the device after the next reset.
OBJECT-TYPE    
  INTEGER perDevice(1), mstp(4)  

rldot1dStpMonitorTime 1.3.6.1.4.1.9.6.1.101.57.2.10
Factor of hello-time during which a port is monotored to determine if it is stable.
OBJECT-TYPE    
  INTEGER 1..20  

rldot1dStpBpduCount 1.3.6.1.4.1.9.6.1.101.57.2.11
The number of bpdu that need to received for the link to be considered stable.
OBJECT-TYPE    
  INTEGER 1..60  

rldot1dStpLastChanged 1.3.6.1.4.1.9.6.1.101.57.2.12
The last time any object in this table was changed by SNMP or other local management means.
OBJECT-TYPE    
  TimeTicks  

rldot1dStpPortTable 1.3.6.1.4.1.9.6.1.101.57.2.13
A table that contains extended pair port specific information.
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1dStpPortEntry

rldot1dStpPortEntry 1.3.6.1.4.1.9.6.1.101.57.2.13.1
A list of information maintained by every port about the Spanning Tree Protocol state for that port.
OBJECT-TYPE    
  Rldot1dStpPortEntry  

rldot1dStpPortPort 1.3.6.1.4.1.9.6.1.101.57.2.13.1.1
The port number of the port for which this entry contains Spanning Tree Protocol management information.
OBJECT-TYPE    
  INTEGER 1..4096  

rldot1dStpPortDampEnable 1.3.6.1.4.1.9.6.1.101.57.2.13.1.2
Specified if dampening is enabled on this port.
OBJECT-TYPE    
  TruthValue  

rldot1dStpPortDampStable 1.3.6.1.4.1.9.6.1.101.57.2.13.1.3
Specified if the port is stable.
OBJECT-TYPE    
  TruthValue  

rldot1dStpPortFilterBpdu 1.3.6.1.4.1.9.6.1.101.57.2.13.1.4
Specified if this port should filter bpdus when stp is disabled.
OBJECT-TYPE    
  INTEGER false(0), true(1), none(2)  

rldot1dStpPortBpduSent 1.3.6.1.4.1.9.6.1.101.57.2.13.1.5
Specified the number of bpdu sent from this port.
OBJECT-TYPE    
  Counter32  

rldot1dStpPortBpduReceived 1.3.6.1.4.1.9.6.1.101.57.2.13.1.6
Specified the number of bpdu received in this port.
OBJECT-TYPE    
  Counter32  

rldot1dStpPortRole 1.3.6.1.4.1.9.6.1.101.57.2.13.1.7
Specified the role of this this port.
OBJECT-TYPE    
  INTEGER unknown(0), disabled(1), alternate(2), backup(3), root(4), designated(5)  

rldot1dStpBpduType 1.3.6.1.4.1.9.6.1.101.57.2.13.1.8
Specified the type of BPDU transmitted by this port.
OBJECT-TYPE    
  INTEGER stp(0), rstp(1)  

rldot1dStpPortRestrictedRole 1.3.6.1.4.1.9.6.1.101.57.2.13.1.9
If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even if it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected.
OBJECT-TYPE    
  TruthValue  

rldot1dStpPortAutoEdgePort 1.3.6.1.4.1.9.6.1.101.57.2.13.1.10
If TRUE causes the Port when become up, to enter the blocking state, and if during 3 seconds it doesn't receive a BPDU, it will enter the forwarding state.
OBJECT-TYPE    
  TruthValue  

rldot1dStpPortLoopback 1.3.6.1.4.1.9.6.1.101.57.2.13.1.11
Specified loopback was detected on port. Usable for only a short period of time if stp loopback guard is enabled (since port enters into shutdown state).
OBJECT-TYPE    
  TruthValue  

rldot1dStpPortBpduOperStatus 1.3.6.1.4.1.9.6.1.101.57.2.13.1.12
Specified BPDU handling operative status for port.
OBJECT-TYPE    
  INTEGER filter(0), flood(1), bridge(2), stp(3)  

rldot1dStpPortsEnable 1.3.6.1.4.1.9.6.1.101.57.2.14
Enable / Disable spanning tree on ports by default .
OBJECT-TYPE    
  TruthValue  

rldot1dStpTaggedFlooding 1.3.6.1.4.1.9.6.1.101.57.2.15
flooding can be done in tagged bpdu .
OBJECT-TYPE    
  TruthValue  

rldot1dStpPortBelongToVlanDefault 1.3.6.1.4.1.9.6.1.101.57.2.16
The default value of rldot1dStpPortMustBelongToVlan .
OBJECT-TYPE    
  TruthValue  

rldot1dStpEnableByDefault 1.3.6.1.4.1.9.6.1.101.57.2.17
The default value of rldot1dStpEnable .
OBJECT-TYPE    
  TruthValue  

rldot1dStpPortToDefault 1.3.6.1.4.1.9.6.1.101.57.2.18
To order port/s to revert to default setings .
OBJECT-TYPE    
  INTEGER  

rldot1dStpSupportedType 1.3.6.1.4.1.9.6.1.101.57.2.19
The type of stp supported by the device.
OBJECT-TYPE    
  INTEGER perDevice(1), perVlan(2), mstp(3)  

rldot1dStpEdgeportSupportInStp 1.3.6.1.4.1.9.6.1.101.57.2.20
If EdgePort is supported in stpCompatible mode .
OBJECT-TYPE    
  TruthValue  

rldot1dStpFilterBpdu 1.3.6.1.4.1.9.6.1.101.57.2.21
Specified if the device should filter BPDUs when STP is disabled.
OBJECT-TYPE    
  TruthValue  

rldot1dStpFloodBpduMethod 1.3.6.1.4.1.9.6.1.101.57.2.22
Specified flooding method: 1 - classic - untagged to all stp disabled ports 2 - bridging -normal bridging.
OBJECT-TYPE    
  INTEGER classic(0), bridging(1)  

rldot1dStpSeparatedBridges 1.3.6.1.4.1.9.6.1.101.57.2.23
OBJECT IDENTIFIER    

rldot1dStpPortBpduGuardTable 1.3.6.1.4.1.9.6.1.101.57.2.24
A table that contains for each port whether it is bpdu guard .
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1dStpPortBpduGuardEntry

rldot1dStpPortBpduGuardEntry 1.3.6.1.4.1.9.6.1.101.57.2.24.1
A list of information maintained by every port whether it is bpdu guard.
OBJECT-TYPE    
  Rldot1dStpPortBpduGuardEntry  

rldot1dStpPortBpduGuardEnable 1.3.6.1.4.1.9.6.1.101.57.2.24.1.1
Specified if bpdu guard is enabled on this port.
OBJECT-TYPE    
  TruthValue  

rldot1dStpLoopbackGuardEnable 1.3.6.1.4.1.9.6.1.101.57.2.25
Define if STP loopback guard feature is globally enabled.
OBJECT-TYPE    
  TruthValue  

rldot1dStpSeparatedBridgesTable 1.3.6.1.4.1.9.6.1.101.57.2.23.1
Define if separated bridges feature is enabled for each interface.
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1dStpSeparatedBridgesEntry

rldot1dStpSeparatedBridgesEntry 1.3.6.1.4.1.9.6.1.101.57.2.23.1.1
Defines the contents of each line in the rlSeparatedBridgesTable table.
OBJECT-TYPE    
  Rldot1dStpSeparatedBridgesEntry  

rldot1dStpSeparatedBridgesPortEnable 1.3.6.1.4.1.9.6.1.101.57.2.23.1.1.1
This variable indicates whether the separated bridge feature is enabled on a specified ifIndex.
OBJECT-TYPE    
  TruthValue  

rldot1dStpSeparatedBridgesEnable 1.3.6.1.4.1.9.6.1.101.57.2.23.2
Enable / Disable Separated Bridges Feature.
OBJECT-TYPE    
  TruthValue  

rldot1dStpSeparatedBridgesAutoConfig 1.3.6.1.4.1.9.6.1.101.57.2.23.3
Enable / Disable Separated Bridges Automatic Configuration.
OBJECT-TYPE    
  TruthValue  

rldot1dStpDisabledPortStateTable 1.3.6.1.4.1.9.6.1.101.57.2.26
Define stp port state for each stp disabled interface. This is auxiliary MIB emulates stp enabled port behaviour in ASIC for stp disabled port. The MIB contains only stp disabled ports entries
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1dStpDisabledPortStateEntry

rldot1dStpDisabledPortStateEntry 1.3.6.1.4.1.9.6.1.101.57.2.26.1
Defines the contents of each line in the rldot1dStpDisabledPortStateTable table.
OBJECT-TYPE    
  Rldot1dStpDisabledPortStateEntry  

rldot1dStpDisabledPortState 1.3.6.1.4.1.9.6.1.101.57.2.26.1.1
The port's stp state as defined by external application . This state controls what action a port takes on reception of a frame.
OBJECT-TYPE    
  INTEGER blocking(2), listening(3), learning(4), forwarding(5)  

rldot1dExtBase 1.3.6.1.4.1.9.6.1.101.57.3
OBJECT IDENTIFIER    

rldot1dExtBaseMibVersion 1.3.6.1.4.1.9.6.1.101.57.3.1
MIB's version, the current version is 1.
OBJECT-TYPE    
  INTEGER  

rldot1dDeviceCapabilities 1.3.6.1.4.1.9.6.1.101.57.3.2
Indicates the optional parts of private extension of IEEE 802.1D and 802.1Q that are implemented by this device and are manageable through this MIB. Capabilities that are allowed on a per-port basis are indicated in dot1dPortCapabilities.
OBJECT-TYPE    
  OCTET STRING Size(1)  

rldot1wRStp 1.3.6.1.4.1.9.6.1.101.57.4
OBJECT IDENTIFIER    

rldot1wRStpVlanEdgePortTable 1.3.6.1.4.1.9.6.1.101.57.4.1
A table that contains pair specific information for the Rapid Spanning Tree Protocol.
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1wRStpVlanEdgePortEntry

rldot1wRStpVlanEdgePortEntry 1.3.6.1.4.1.9.6.1.101.57.4.1.1
A list of information maintained by every pair about the RAPID Spanning Tree Protocol state for that pair.
OBJECT-TYPE    
  Rldot1wRStpVlanEdgePortEntry  

rldot1wRStpVlanEdgePortVlan 1.3.6.1.4.1.9.6.1.101.57.4.1.1.1
The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information, If STP per device then only one value of 1 is allowed. If STP per a VLAN then all value of 1..4095 are allowed.
OBJECT-TYPE    
  INTEGER 1..4095  

rldot1wRStpVlanEdgePortPort 1.3.6.1.4.1.9.6.1.101.57.4.1.1.2
The port number of the port for which this entry contains Spanning Tree Protocol management information.
OBJECT-TYPE    
  INTEGER  

rldot1wRStpEdgePortStatus 1.3.6.1.4.1.9.6.1.101.57.4.1.1.3
Specifies whether this port is an Edge Port or not
OBJECT-TYPE    
  TruthValue  

rldot1wRStpForceVersionTable 1.3.6.1.4.1.9.6.1.101.57.4.2
A table that contains specific information for the Rapid Spanning Tree Protocol.
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1wRStpForceVersionEntry

rldot1wRStpForceVersionEntry 1.3.6.1.4.1.9.6.1.101.57.4.2.1
A list of information maintained by every about the RAPID Spanning Tree Protocol state for that pair.
OBJECT-TYPE    
  Rldot1wRStpForceVersionEntry  

rldot1wRStpForceVersionVlan 1.3.6.1.4.1.9.6.1.101.57.4.2.1.1
The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information, If STP per device then only one value of 1 is allowed. If STP per a VLAN then all value of 1..4095 are allowed.
OBJECT-TYPE    
  INTEGER 1..4095  

rldot1wRStpForceVersionState 1.3.6.1.4.1.9.6.1.101.57.4.2.1.2
Specifies whether this Bridge uses the normal RSTP algorithm, or STP Compatibility algorythm: 0 - STP Compatibility 2 - Normal RSTP
OBJECT-TYPE    
  INTEGER  

rldot1pPriorityMap 1.3.6.1.4.1.9.6.1.101.57.5
OBJECT IDENTIFIER    

rldot1pPriorityMapState 1.3.6.1.4.1.9.6.1.101.57.5.1
enable / disable
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rldot1pPriorityMapTable 1.3.6.1.4.1.9.6.1.101.57.5.2
This table hold information the priority maps
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1pPriorityMapEntry

rldot1pPriorityMapEntry 1.3.6.1.4.1.9.6.1.101.57.5.2.1
The row definition for this table.
OBJECT-TYPE    
  Rldot1pPriorityMapEntry  

rldot1pPriorityMapName 1.3.6.1.4.1.9.6.1.101.57.5.2.1.1
The map name
OBJECT-TYPE    
  DisplayString Size(1..25)  

rldot1pPriorityMapPriority 1.3.6.1.4.1.9.6.1.101.57.5.2.1.2
The map holding the queue
OBJECT-TYPE    
  OCTET STRING Size(8)  

rldot1pPriorityMapPort 1.3.6.1.4.1.9.6.1.101.57.5.2.1.3
the port that the map, is applied on in config
OBJECT-TYPE    
  PortList  

rldot1pPriorityMapPortList 1.3.6.1.4.1.9.6.1.101.57.5.2.1.4
the ports that the map, is applied on in actual
OBJECT-TYPE    
  PortList  

rldot1pPriorityMapStatus 1.3.6.1.4.1.9.6.1.101.57.5.2.1.5
The status of the table entry. It's used to delete an entry
OBJECT-TYPE    
  RowStatus  

rldot1sMstp 1.3.6.1.4.1.9.6.1.101.57.6
OBJECT IDENTIFIER    

rldot1sMstpInstanceTable 1.3.6.1.4.1.9.6.1.101.57.6.1
A table that contains Mstp instance specific information for the Multiple Spanning Tree Protocol.
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1sMstpInstanceEntry

rldot1sMstpInstanceEntry 1.3.6.1.4.1.9.6.1.101.57.6.1.1
A list of information maintained by every instance about the multiple Spanning Tree Protocol state for that instance.
OBJECT-TYPE    
  Rldot1sMstpInstanceEntry  

rldot1sMstpInstanceId 1.3.6.1.4.1.9.6.1.101.57.6.1.1.1
The Instance index.
OBJECT-TYPE    
  INTEGER 1..64  

rldot1sMstpInstanceEnable 1.3.6.1.4.1.9.6.1.101.57.6.1.1.2
Specifies whether this Instance is STP enable or disable
OBJECT-TYPE    
  TruthValue  

rldot1sMstpInstanceTimeSinceTopologyChange 1.3.6.1.4.1.9.6.1.101.57.6.1.1.3
The time (in hundredths of a second) since the last time a topology change was detected by the Mstp Instance .
OBJECT-TYPE    
  TimeTicks  

rldot1sMstpInstanceTopChanges 1.3.6.1.4.1.9.6.1.101.57.6.1.1.4
The total number of topology changes detected by this Instance since the management entity was last reset or initialized.
OBJECT-TYPE    
  Counter  

rldot1sMstpInstanceDesignatedRoot 1.3.6.1.4.1.9.6.1.101.57.6.1.1.5
The bridge identifier of the root of the spanning tree as determined by the Muliple Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
OBJECT-TYPE    
  BridgeId  

rldot1sMstpInstanceRootCost 1.3.6.1.4.1.9.6.1.101.57.6.1.1.6
The cost of the path to the root as seen from this bridge.
OBJECT-TYPE    
  INTEGER  

rldot1sMstpInstanceRootPort 1.3.6.1.4.1.9.6.1.101.57.6.1.1.7
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
OBJECT-TYPE    
  INTEGER  

rldot1sMstpInstanceMaxAge 1.3.6.1.4.1.9.6.1.101.57.6.1.1.8
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
OBJECT-TYPE    
  Timeout  

rldot1sMstpInstanceHelloTime 1.3.6.1.4.1.9.6.1.101.57.6.1.1.9
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
OBJECT-TYPE    
  Timeout  

rldot1sMstpInstanceHoldTime 1.3.6.1.4.1.9.6.1.101.57.6.1.1.10
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
OBJECT-TYPE    
  INTEGER  

rldot1sMstpInstanceForwardDelay 1.3.6.1.4.1.9.6.1.101.57.6.1.1.11
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
OBJECT-TYPE    
  Timeout  

rldot1sMstpInstancePriority 1.3.6.1.4.1.9.6.1.101.57.6.1.1.12
The value of the write-able portion of the Bridge ID, i.e., the first four bits of the first octet of the (8 octet long) Bridge ID.The value is a product of 4096. The next 12 bit are the msti id . The other (last) 6 octets of the Bridge ID are given by the value of dot1dBaseBridgeAddress.
OBJECT-TYPE    
  INTEGER 0..61440  

rldot1sMstpInstanceRemainingHopes 1.3.6.1.4.1.9.6.1.101.57.6.1.1.13
This count value determines the amount of hopes the information transmited by this bridge on this instance can travel.
OBJECT-TYPE    
  INTEGER  

rldot1sMstpInstancePortTable 1.3.6.1.4.1.9.6.1.101.57.6.2
A table that contains pair specific information for the Spanning Tree Protocol.
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1sMstpInstancePortEntry

rldot1sMstpInstancePortEntry 1.3.6.1.4.1.9.6.1.101.57.6.2.1
A list of information maintained by every pair about the Spanning Tree Protocol state for that pair.
OBJECT-TYPE    
  Rldot1sMstpInstancePortEntry  

rldot1sMstpInstancePortMstiId 1.3.6.1.4.1.9.6.1.101.57.6.2.1.1
The Vlan group number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information.
OBJECT-TYPE    
  INTEGER 1..64  

rldot1sMstpInstancePortPort 1.3.6.1.4.1.9.6.1.101.57.6.2.1.2
The port number of the port for which this entry contains Spanning Tree Protocol management information.
OBJECT-TYPE    
  INTEGER 1..4096  

rldot1sMstpInstancePortPriority 1.3.6.1.4.1.9.6.1.101.57.6.2.1.3
The value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The value is a product of 16. The other octet of the Port ID is given by the value of rldot1dStpVlanGroupPort.
OBJECT-TYPE    
  INTEGER 0..240  

rldot1sMstpInstancePortState 1.3.6.1.4.1.9.6.1.101.57.6.2.1.4
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpVlanPortEnable), this object will have a value of disabled(1).
OBJECT-TYPE    
  INTEGER disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)  

rldot1sMstpInstancePortEnable 1.3.6.1.4.1.9.6.1.101.57.6.2.1.5
The enabled/disabled status of the port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

rldot1sMstpInstancePortPathCost 1.3.6.1.4.1.9.6.1.101.57.6.2.1.6
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
OBJECT-TYPE    
  INTEGER 1..200000000  

rldot1sMstpInstancePortDesignatedRoot 1.3.6.1.4.1.9.6.1.101.57.6.2.1.7
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
OBJECT-TYPE    
  BridgeId  

rldot1sMstpInstancePortDesignatedCost 1.3.6.1.4.1.9.6.1.101.57.6.2.1.8
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OBJECT-TYPE    
  INTEGER  

rldot1sMstpInstancePortDesignatedBridge 1.3.6.1.4.1.9.6.1.101.57.6.2.1.9
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
OBJECT-TYPE    
  BridgeId  

rldot1sMstpInstancePortDesignatedPort 1.3.6.1.4.1.9.6.1.101.57.6.2.1.10
The Port Identifier of the port on the Designated Bridge for this port's segment.
OBJECT-TYPE    
  OCTET STRING Size(2)  

rldot1sMstpInstancePortForwardTransitions 1.3.6.1.4.1.9.6.1.101.57.6.2.1.11
The number of times this port has transitioned from the Learning state to the Forwarding state.
OBJECT-TYPE    
  Counter  

rldot1sMStpInstancePortAdminPathCost 1.3.6.1.4.1.9.6.1.101.57.6.2.1.12
The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object dot1dStpPortPathCost, which returns the operational value of the path cost.
OBJECT-TYPE    
  INTEGER 0..200000000  

rldot1sMStpInstancePortRole 1.3.6.1.4.1.9.6.1.101.57.6.2.1.13
Specify the role of this this port.
OBJECT-TYPE    
  INTEGER unknown(0), disabled(1), alternate(2), backup(3), root(4), designated(5), master(6)  

rldot1sMstpMaxHopes 1.3.6.1.4.1.9.6.1.101.57.6.3
Max number of hopes that an MST BPDU will travel inside a region.
OBJECT-TYPE    
  INTEGER 1..40  

rldot1sMstpConfigurationName 1.3.6.1.4.1.9.6.1.101.57.6.4
The active configuration name as will be caried in MST BPDU's.
OBJECT-TYPE    
  SnmpAdminString  

rldot1sMstpRevisionLevel 1.3.6.1.4.1.9.6.1.101.57.6.5
The active revision level.
OBJECT-TYPE    
  INTEGER 0..65535  

rldot1sMstpVlanTable 1.3.6.1.4.1.9.6.1.101.57.6.6
A table that contains information about the alocation of vlans to groups.
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1sMstpVlanEntry

rldot1sMstpVlanEntry 1.3.6.1.4.1.9.6.1.101.57.6.6.1
A list of information maintained by every vlan about the group it belongs to.
OBJECT-TYPE    
  Rldot1sMstpVlanEntry  

rldot1sMstpVlan 1.3.6.1.4.1.9.6.1.101.57.6.6.1.1
The vlan number of the vlan for which this entry contains Spanning Tree Protocol management information.
OBJECT-TYPE    
  INTEGER 1..4094  

rldot1sMstpGroup 1.3.6.1.4.1.9.6.1.101.57.6.6.1.2
Specifid the active group number this vlan belonges to.
OBJECT-TYPE    
  INTEGER 0..64  

rldot1sMstpPendingGroup 1.3.6.1.4.1.9.6.1.101.57.6.6.1.3
Specifid the pending group number this vlan belonges to.
OBJECT-TYPE    
  INTEGER 0..64  

rldot1sMstpExtPortTable 1.3.6.1.4.1.9.6.1.101.57.6.7
A table that contains MSTP information about ports of the CIST.
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1sMstpExtPortEntry

rldot1sMstpExtPortEntry 1.3.6.1.4.1.9.6.1.101.57.6.7.1
A list of information maintained by every port of the CIST.
OBJECT-TYPE    
  Rldot1sMstpExtPortEntry  

rldot1sMstpExtPortPort 1.3.6.1.4.1.9.6.1.101.57.6.7.1.1
The port number of the port for which this entry contains Spanning Tree Protocol management information.
OBJECT-TYPE    
  INTEGER 1..4096  

rldot1sMstpExtPortInternalOperPathCost 1.3.6.1.4.1.9.6.1.101.57.6.7.1.2
The contribution of this port to the path cost of paths towards the spanning tree regional root which include this port. 802.1S-2002 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
OBJECT-TYPE    
  INTEGER 1..200000000  

rldot1sMstpExtPortDesignatedRegionalRoot 1.3.6.1.4.1.9.6.1.101.57.6.7.1.3
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
OBJECT-TYPE    
  BridgeId  

rldot1sMstpExtPortDesignatedRegionalCost 1.3.6.1.4.1.9.6.1.101.57.6.7.1.4
The regional path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OBJECT-TYPE    
  INTEGER  

rldot1sMstpExtPortBoundary 1.3.6.1.4.1.9.6.1.101.57.6.7.1.5
Indication if the port is conented to to a lan segment outside or inside the region.
OBJECT-TYPE    
  TruthValue  

rldot1sMstpExtPortInternalAdminPathCost 1.3.6.1.4.1.9.6.1.101.57.6.7.1.6
The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object dot1dStpPortPathCost, which returns the operational value of the path cost.
OBJECT-TYPE    
  INTEGER 0..200000000  

rldot1sMstpDesignatedMaxHopes 1.3.6.1.4.1.9.6.1.101.57.6.8
Max number of hopes that an MST BPDU will travel inside a region.
OBJECT-TYPE    
  INTEGER 1..40  

rldot1sMstpRegionalRoot 1.3.6.1.4.1.9.6.1.101.57.6.9
CIST Regional Root Identifier (13.16.4). The Bridge Identifier of the current CIST Regional Root.
OBJECT-TYPE    
  BridgeId  

rldot1sMstpRegionalRootCost 1.3.6.1.4.1.9.6.1.101.57.6.10
The CIST path cost from the transmitting Bridge to the CIST Regional Root.
OBJECT-TYPE    
  INTEGER  

rldot1sMstpPendingConfigurationName 1.3.6.1.4.1.9.6.1.101.57.6.11
The pending configuration name.
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

rldot1sMstpPendingRevisionLevel 1.3.6.1.4.1.9.6.1.101.57.6.12
The pending revision level.
OBJECT-TYPE    
  INTEGER 0..65535  

rldot1sMstpPendingAction 1.3.6.1.4.1.9.6.1.101.57.6.13
The action to be done with the pending configuration. copyPendingActive - to copy the pending mst configuration to the active one. copyActivePending - to copy the active mst configuration to the pending one.
OBJECT-TYPE    
  INTEGER copyPendingActive(1), copyActivePending(2)  

rldot1sMstpRemainingHops 1.3.6.1.4.1.9.6.1.101.57.6.14
This count value determines the amount of hops the information transmitted by this bridge can travel.
OBJECT-TYPE    
  INTEGER  

rldot1sMstpInstanceVlanTable 1.3.6.1.4.1.9.6.1.101.57.6.15
This table contains vlan lists per MSTP instances.
OBJECT-TYPE    
  SEQUENCE OF  
    Rldot1sMstpInstanceVlanEntry

rldot1sMstpInstanceVlanEntry 1.3.6.1.4.1.9.6.1.101.57.6.15.1
The entry contains vlan lists per specific MSTP instance.
OBJECT-TYPE    
  Rldot1sMstpInstanceVlanEntry  

rldot1sMstpInstanceVlanId 1.3.6.1.4.1.9.6.1.101.57.6.15.1.1
Specifiy the instance number.
OBJECT-TYPE    
  INTEGER 0..64  

rldot1sMstpInstanceVlanId1To1024 1.3.6.1.4.1.9.6.1.101.57.6.15.1.2
first VlanId List of specific MSTP instance.
OBJECT-TYPE    
  VlanList1  

rldot1sMstpInstanceVlanId1025To2048 1.3.6.1.4.1.9.6.1.101.57.6.15.1.3
second VlanId List of specific MSTP instance.
OBJECT-TYPE    
  VlanList2  

rldot1sMstpInstanceVlanId2049To3072 1.3.6.1.4.1.9.6.1.101.57.6.15.1.4
third VlanId List of specific MSTP instance.
OBJECT-TYPE    
  VlanList3  

rldot1sMstpInstanceVlanId3073To4094 1.3.6.1.4.1.9.6.1.101.57.6.15.1.5
fourth VlanId List of specific MSTP instance.
OBJECT-TYPE    
  VlanList4  

rldot1dTpAgingTime 1.3.6.1.4.1.9.6.1.101.57.7
OBJECT IDENTIFIER    

rldot1dTpAgingTimeMin 1.3.6.1.4.1.9.6.1.101.57.7.1
The min timeout period in seconds for aging out dynamically learned forwarding information.
OBJECT-TYPE    
  INTEGER  

rldot1dTpAgingTimeMax 1.3.6.1.4.1.9.6.1.101.57.7.2
The max timeout period in seconds for aging out dynamically learned forwarding information.
OBJECT-TYPE    
  INTEGER