CISCO-ZS-MIB
File:
CISCO-ZS-MIB.mib (193571 bytes)
Imported modules
Imported symbols
Defined Types
ZoneMemberType |
|
Represents the addressing mechanism by
which a member is identified.
wwn(1) - The Port World Wide Name (PWWN).
domainPort(2) - Domain and Port number format.
fcAddr(3) - FC-ID.
fwwn(4) - Fabric Port World Wide Name. This
is used for Port based zoning.
symNodeName(5) - Symbolic Node Name used for
iSCSI zoning.
intf(6) - interface format.
domainIntf(7) - Domain and Interface format.
ipAddr(8) - IPv4 address format.
ipAddrv6(9) - IPv6 address format.
deviceAlias(10) - Device Alias. This is a human
readable string used to alias
a World Wide Name (WWN). It is
defined in CISCO-FC-DEVICE-ALIAS-MIB. |
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
wwn(1), domainPort(2), fcAddr(3), fwwn(4), symNodeName(5), intf(6), domainIntf(7), ipAddr(8), ipAddrv6(9), deviceAlias(10) |
|
FcZoneServerRejReasonExpl |
|
The reject reason code explanation for a zone server
request.
noAdditionalExplanation(1) - there is no additional
explanation.
zonesNotSupported(2) - zones are not supported.
zoneSetNameUnknown(3) - zone set name is not known.
noZoneSetActive(4) - no zone set is currently active.
zoneNameUnknown(5) - zone name is unknown.
zoneStateUnknown(6) - state of the zone is not known.
incorrectPayloadLen(7) - payload len is not correct.
tooLargeZoneSet(8) - zone set is larger than
permitted size.
deactivateZoneSetFailed(9) - deactivation of zone set
failed.
reqNotSupported(10) - request is not supported.
capabilityNotSupported(11) - capability is not
supported.
zoneMemberIDTypeNotSupp(12)- type of zone member is not
supported.
invalidZoneSetDefinition(13) - zone set definition is
invalid. |
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
noAdditionalExplanation(1), zonesNotSupported(2), zoneSetNameUnknown(3), noZoneSetActive(4), zoneNameUnknown(5), zoneStateUnknown(6), incorrectPayloadLen(7), tooLargeZoneSet(8), deactivateZoneSetFailed(9), reqNotSupported(10), capabilityNotSupported(11), zoneMemberIDTypeNotSupp(12), invalidZoneSetDefinition(13) |
|
FcList |
|
Represents a list of entities.
Each octet within the value of an object of this type,
specifies a set of eight entities, with the first
octet specifying entities 1 through 8, the second
octet specifying entities 9 through 16, etc.
Within each octet, the most significant bit
represents the lowest numbered entity and the
least significant bit represents the highest
numbered entity.
If the length of an object of this type is less
than 256 bytes, then the entities which are not
represented are not considered to be part of this
list, i.e., effectively, the string is extended to
be of length 256 bytes by appending bytes
containing x'00'. Note that this means that the
zero length string represents the 'list is empty'
value. |
TEXTUAL-CONVENTION |
|
|
|
|
OCTET STRING |
Size(0..256) |
|
FcChangeProtoFailCause |
|
The reason for the failure of Change Protocol, which
kicks in due to zone set activation/de-activation.
none(1) - no error.
rcvdSfcBusy(2) - the local Zone Server received a busy
from one of the Zone Servers in the
fabric in response to SFC.
rcvdUfcBusy(3) - the local Zone Server received a busy
from one of the Zone Servers in the
fabric in response to UFC.
acaRetryExceed(4) - the number of ACA retries by
the local Zone Server has exceeded
the retry count.
sfcRetryExceed(5) - the number of SFC retries by the
local Zone Server has exceeded the
retry count.
ufcRetryExceed(6) - the number of UFC retries by the
local Zone Server has exceeded the
retry count.
unsuppCmd(7) - the local Zone Server has received response
from one of the Zone Servers in the fabric
that it does not support the particular
command.
notAuth(8) - the local Zone Server has received response
from one of the Zone Servers in the fabric
that the local Zone Server is not authorized
to carry out the particular command.
fabricChange(9) - the local Zone Server has received
response from one of the Zone Servers
that the fabric from it's viewpoint
is changing.
updateNotStaged(10) - the local Zone Server has received
response from one of the Zone Servers
in the fabric that it has received
a UFC before an SFC.
invalidZsetFormat(11) - the local Zone Server has received
response from one of the Zone
Servers in the fabric that the zone
set format in the pdu sent to it is
invalid.
systemErr(12) - a system error has occured on the local Zone
Server.
vsanNotPresent(13) - the specified VSAN is not present on
the local Zone Server.
vsanInactive(14) - the specifed VSAN is not active on the
local Zone Server.
zsetNotPresent(15) - the specified zone set is not present
on the local Zone Server.
dbUpdateInProgress(16) - the local Zone Server's database
is being updated.
zsetNotActive(17) - the zone set specified for
deactivation is not active on the
local Zone Server.
hwOperFailed(18) - the hardware update on the local Zone
Server failed.
fc2SeqSizeExceed(19) - the Change Protocol frame has
exceeded the allowed maximum FC-2
sequence size on the local
Zone Server.
fc2SendFailed(20) - the FC-2 stack failed to send the
frame on the local Zone Server.
zsetUnchangedAndActive(21) - the zone set specified for
activation is already active
and unchanged since the last
activation on the local Zone
Server.
fabricUnstable(22) - the fabric has become unstable as
detected by the local Zone Server.
nonInteropMember(23) - one or more of the members specified
in the zone set(s) to be activated,
are in non-interoperable format and
the interop mode is turned on, on
the local Zone Server.
lcUpgradeInProgress(24) - line card upgrade is in progress
on the local Zone Server. |
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
none(1), rcvdSfcBusy(2), rcvdUfcBusy(3), acaRetryExceed(4), sfcRetryExceed(5), ufcRetryExceed(6), unsuppCmd(7), notAuth(8), fabricChange(9), updateNotStaged(10), invalidZsetFormat(11), systemErr(12), vsanNotPresent(13), vsanInactive(14), zsetNotPresent(15), dbUpdateInProgress(16), zsetNotActive(17), hwOperFailed(18), fc2SeqSizeExceed(19), fc2SendFailed(20), zsetUnchangedAndActive(21), fabricUnstable(22), nonInteropMember(23), lcUpgradeInProgress(24) |
|
ZoneCopyProtocol |
|
The protocol to be used for copying the active
zoneset over the network. If the copy is to
occur on the local device, then the method of
transfer is left to the implementation and is
not restricted to these protocols. |
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
tftp(1), ftp(2), sftp(3), scp(4) |
|
ZoneFileType |
|
The various types of files onto which the
active zoneset can be copied.
networkFile(1) - the active zoneset needs
to be copied over the
network.
localFile(2) - the active zoneset needs to
be copied to a file on the
local device. |
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
networkFile(1), localFile(2) |
|
ZoneQosPriorityLevel |
|
Specifies the priority level for qos
attribute applied to a zone.
none - not applicable.
low - indicates low priority.
medium - indicates medium priority.
high - indicates high priority. |
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
none(1), low(2), medium(3), high(4) |
|
ZoneMergeFailCause |
|
Specifies the reason for zone merge failure.
When the Zone Merge takes place, the local
database is compared with the database of
the adjacent switch. The following
errors/mismatches can take place:
other - reason other than those specified
below.
zoningModeMismatch - mismatch in zoning modes
between the 2 switches.
qosNotEnabled - qos is not enabled on one of
the switches and qos
attribute is present in one
of the zones.
qosConflict - conflict between VSAN based Qos
and zone attribute qos.
bcastNotEnabled - broadcast service has not
been enabled on one of the
switches and broadcast
attribute is present in
one of the zones.
mergeCtrlMismatch - there is a mismatch in the
merge control flag value.
defZoneMismatch - there is a mismatch in the
default zone policy.
qosAttrMissing - qos attribute is missing.
bcastAttrMissing - broadcast attribute is
missing.
rdonlyAttrMissing - read only attribute is
missing.
memberMismatch - there is a mismatch in the
members.
invPayloadFormat - the payload format is
invalid.
sizeExceeded - the payload exceeded the
maximum size.
unlicensedMember - a member is unlicensed.
nonInteropZoneset - a zone attribute/member
which cannot be supported
in the current interop
mode of the switch. |
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
other(1), zoningModeMismatch(2), qosNotEnabled(3), qosConflict(4), bcastNotEnabled(5), mergeCtrlMismatch(6), defZoneMismatch(7), qosAttrMissing(8), bcastAttrMissing(9), rdonlyAttrMissing(10), memberMismatch(11), invPayloadFormat(12), sizeExceeded(13), unlicensedMember(14), nonInteropZoneset(15) |
|
ZoneDefaultZoneEntry |
|
SEQUENCE |
|
|
|
|
zoneDefaultZoneBehaviour |
INTEGER |
|
|
zoneDefaultZoneReadOnly |
TruthValue |
|
|
zoneDefaultZoneQos |
TruthValue |
|
|
zoneDefaultZoneQosPriority |
ZoneQosPriorityLevel |
|
|
zoneDefaultZoneBroadcast |
TruthValue |
|
ZoneSetPropagationEntry |
|
SEQUENCE |
|
|
|
|
zoneSetPropagationMode |
INTEGER |
|
ZoneSetEntry |
|
SEQUENCE |
|
|
|
|
zoneSetIndex |
Unsigned32 |
|
|
zoneSetName |
SnmpAdminString |
|
|
zoneSetZoneList |
FcList |
|
|
zoneSetLastChange |
TimeStamp |
|
|
zoneSetRowStatus |
RowStatus |
|
|
zoneSetClone |
SnmpAdminString |
|
ZoneSetActivateEntry |
|
SEQUENCE |
|
|
|
|
zoneSetActivate |
Unsigned32 |
|
|
zoneSetActivateResult |
INTEGER |
|
|
zoneSetDeActivate |
INTEGER |
|
|
zoneSetActivateRowStatus |
RowStatus |
|
|
zoneSetFailCause |
FcChangeProtoFailCause |
|
|
zoneSetFailDomId |
DomainIdOrZero |
|
ZoneEntry |
|
SEQUENCE |
|
|
|
|
zoneIndex |
Unsigned32 |
|
|
zoneName |
SnmpAdminString |
|
|
zoneMemberList |
FcList |
|
|
zoneAliasList |
FcList |
|
|
zoneLastChange |
TimeStamp |
|
|
zoneRowStatus |
RowStatus |
|
|
zoneReadOnly |
TruthValue |
|
|
zoneQos |
TruthValue |
|
|
zoneQosPriority |
ZoneQosPriorityLevel |
|
|
zoneBroadcast |
TruthValue |
|
|
zoneClone |
SnmpAdminString |
|
ZoneAliasEntry |
|
SEQUENCE |
|
|
|
|
zoneAliasIndex |
Unsigned32 |
|
|
zoneAliasName |
SnmpAdminString |
|
|
zoneAliasMemberList |
FcList |
|
|
zoneAliasRowStatus |
RowStatus |
|
|
zoneAliasLastChange |
TimeStamp |
|
|
zoneAliasClone |
SnmpAdminString |
|
ZoneMemberEntry |
|
SEQUENCE |
|
|
|
|
zoneMemberTypeIndex |
INTEGER |
|
|
zoneMemberParentIndex |
Unsigned32 |
|
|
zoneMemberIndex |
Unsigned32 |
|
|
zoneMemberFormat |
ZoneMemberType |
|
|
zoneMemberID |
OCTET STRING |
|
|
zoneMemberLunID |
OCTET STRING |
|
|
zoneMemberRowStatus |
RowStatus |
|
ZoneEnforcedZoneSetEntry |
|
SEQUENCE |
|
|
|
|
zoneEnforcedZoneSetName |
SnmpAdminString |
|
|
zoneEnforcedZoneSetZoneList |
FcList |
|
|
zoneEnforcedZoneSetActivateTime |
TimeStamp |
|
ZoneEnforcedZoneEntry |
|
SEQUENCE |
|
|
|
|
zoneEnforcedZoneName |
SnmpAdminString |
|
|
zoneEnforcedZoneMemberList |
FcList |
|
|
zoneEnforcedZoneAliasList |
FcList |
|
|
zoneEnforcedZoneActivateTime |
TimeStamp |
|
|
zoneEnforcedZoneReadOnly |
TruthValue |
|
|
zoneEnforcedZoneQos |
TruthValue |
|
|
zoneEnforcedZoneQosPriority |
ZoneQosPriorityLevel |
|
|
zoneEnforcedZoneBroadcast |
TruthValue |
|
ZoneEnforcedZoneAliasEntry |
|
SEQUENCE |
|
|
|
|
zoneEnforcedZoneAliasName |
SnmpAdminString |
|
|
zoneEnforcedZoneAliasMemberList |
FcList |
|
ZoneEnforcedZoneMemberEntry |
|
SEQUENCE |
|
|
|
|
zoneEnforcedZoneMemberFormat |
ZoneMemberType |
|
|
zoneEnforcedZoneMemberID |
OCTET STRING |
|
|
zoneEnforcedZoneMemberLunID |
OCTET STRING |
|
ZoneStatsEntry |
|
SEQUENCE |
|
|
|
|
zoneTxMergeReqs |
Counter32 |
|
|
zoneRxMergeAccepts |
Counter32 |
|
|
zoneRxMergeReqs |
Counter32 |
|
|
zoneTxMergeAccepts |
Counter32 |
|
|
zoneTxChangeReqs |
Counter32 |
|
|
zoneRxChangeAccepts |
Counter32 |
|
|
zoneRxChangeReqs |
Counter32 |
|
|
zoneTxChangeAccepts |
Counter32 |
|
|
zoneRxGS3Reqs |
Counter32 |
|
|
zoneTxGS3Rejects |
Counter32 |
|
ZoneLunStatsEntry |
|
SEQUENCE |
|
|
|
|
zoneLunSrcFcId |
FcAddressId |
|
|
zoneLunDstFcId |
FcAddressId |
|
|
zoneLunNum |
OCTET STRING |
|
|
zoneLunRxInqReqs |
Counter32 |
|
|
zoneLunRxRepLunReqs |
Counter32 |
|
|
zoneLunRxSenseReqs |
Counter32 |
|
|
zoneLunRxOtherCmds |
Counter32 |
|
|
zoneLunTxInqDataNoLus |
Counter32 |
|
|
zoneLunTxIllegalReqs |
Counter32 |
|
ZoneRoZoneStatsEntry |
|
SEQUENCE |
|
|
|
|
zoneRoZoneSrcFcId |
FcAddressId |
|
|
zoneRoZoneDstFcId |
FcAddressId |
|
|
zoneRoZoneLunNum |
OCTET STRING |
|
|
zoneRoZoneTxDataProts |
Counter32 |
|
ZoneDbEntry |
|
SEQUENCE |
|
|
|
|
zoneDbClearDb |
INTEGER |
|
|
zoneDbEnforcedEqualsLocal |
TruthValue |
|
|
zoneDbHardZoningEnabled |
TruthValue |
|
ZoneCopyEntry |
|
SEQUENCE |
|
|
|
|
zoneCopyProto |
ZoneCopyProtocol |
|
|
zoneCopyDestFileType |
ZoneFileType |
|
|
zoneCopyServerAddrType |
InetAddressType |
|
|
zoneCopyServerAddr |
InetAddress |
|
|
zoneCopyDestFileName |
SnmpAdminString |
|
|
zoneCopyUserName |
SnmpAdminString |
|
|
zoneCopyUserPassword |
SnmpAdminString |
|
|
zoneCopyStartCopy |
INTEGER |
|
|
zoneCopyState |
INTEGER |
|
|
zoneCopyRowStatus |
RowStatus |
|
ZoneSetZoneListEntry |
|
SEQUENCE |
|
|
|
|
zoneSetZoneListBmap4k |
FcList |
|
|
zoneSetZoneListBmap6k |
FcList |
|
|
zoneSetZoneListBmap8k |
FcList |
|
ZoneSetEnforcedZoneListEntry |
|
SEQUENCE |
|
|
|
|
zoneSetEnforcedZoneListBmap4k |
FcList |
|
|
zoneSetEnforcedZoneListBmap6k |
FcList |
|
|
zoneSetEnforcedZoneListBmap8k |
FcList |
|
ZoneCompactEntry |
|
SEQUENCE |
|
|
|
|
zoneCompactFirst2k |
INTEGER |
|
Defined Values
ciscoZsMIB |
1.3.6.1.4.1.9.9.294 |
The MIB module for the management of zoning within
the framework of Cisco's Zoning Server (ZS) Archi-
tecture which realizes the FC-GS3 requirements for
Zone Server. This MIB enables managers to configure
and monitor zoning server parameters.
Additionally, Cisco's Zoning Server allows for
configuration of Lun zoning, which is an extension
to the Zoning Server standard specified by FC-GS3.
Glossary of terms used
----------------------
VSAN - Virtual Storage Area Network.
Zone Merge - When the ISL (Inter Switch Link)
between 2 switches is brought up,
the zoning databases on the 2
switches are compared by means of
the Zone Merge protocol. If the
2 databases can be merged, the
ISL is brought up. Otherwise,
the link is isolated. |
MODULE-IDENTITY |
|
|
|
zoneStats |
1.3.6.1.4.1.9.9.294.1.2 |
OBJECT IDENTIFIER |
|
|
|
zoneDefaultZoneTable |
1.3.6.1.4.1.9.9.294.1.1.1 |
A table containing information on all
default zones on all VSANs on the local
Zone Server. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneDefaultZoneEntry |
|
zoneDefaultZoneEntry |
1.3.6.1.4.1.9.9.294.1.1.1.1 |
An entry (conceptual row) in this table. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneDefaultZoneEntry |
|
|
zoneDefaultZoneBehaviour |
1.3.6.1.4.1.9.9.294.1.1.1.1.1 |
This object controls the behaviour of the
default zone on this VSAN.
If this object is set to 'permit', then the
members of the default zone on this VSAN can
communicate with each other.
If this object is set to 'deny', then the
members of the default zone on this VSAN cannot
communicate with each other. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
permit(1), deny(2) |
|
zoneDefaultZoneReadOnly |
1.3.6.1.4.1.9.9.294.1.1.1.1.2 |
This object indicates if only SCSI read
operations are allowed on members of the
default zone which are SCSI targets, on
this VSAN.
If this object is set to 'true', then only
SCSI read operations are permitted. So, this
default zone becomes a read-only default zone
on this VSAN.
If this object is set to 'false', then both
SCSI read and write operations are permitted. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneDefaultZoneQos |
1.3.6.1.4.1.9.9.294.1.1.1.1.3 |
This object specifies if qos attribute for the
default zone on this VSAN is enabled. If this object
is set to 'true', then qos attribute for the default
zone on this VSAN is enabled.
If this object is set to 'false', then qos
attribute for the default zone on this VSAN is
disabled.
If this attribute is enabled for this default zone,
then only traffic with the configured priority
level will be allowed between the members of
this default zone. The priority can be specified by
means of the corresponding instance of
zoneDefaultZoneQosPriority object. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneDefaultZoneQosPriority |
1.3.6.1.4.1.9.9.294.1.1.1.1.4 |
Specifies the qos priority value. The value of
this object is relevant only if the corresponding
instance of zoneDefaultZoneQos object is enabled by
setting it to 'true'. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
ZoneQosPriorityLevel |
|
|
zoneDefaultZoneBroadcast |
1.3.6.1.4.1.9.9.294.1.1.1.1.5 |
This object specifies if broadcast zoning is
enabled on this default zone on this VSAN. If
this object is set to 'true', then it is enabled.
If this object is set to 'false', then it is disabled.
If broadcast zoning is enabled on this default zone,
then broadcast frames generated by a member in this
default zone will be restricted to members in this
default zone. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneSetPropagationTable |
1.3.6.1.4.1.9.9.294.1.1.2 |
A table containing information related to
propagation of zone set information during
Merge/Change protocols on all VSANs on the
local Zone Server. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneSetPropagationEntry |
|
zoneSetPropagationEntry |
1.3.6.1.4.1.9.9.294.1.1.2.1 |
An entry (conceptual row) in this table. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneSetPropagationEntry |
|
|
zoneSetPropagationMode |
1.3.6.1.4.1.9.9.294.1.1.2.1.1 |
This object controls the way zone set
information is propagated during
Merge/Change protocols on this VSAN.
If this object is set to 'fullZoneSet',
then the entire zone set database is
sent during Change/Merge protocol
exchanges on this VSAN.
If this object is set to 'activeZoneSet',
only the active zone set is sent during
Change/Merge protocol exchanges on this
VSAN. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
fullZoneSet(1), activeZoneSet(2) |
|
zoneSetNumber |
1.3.6.1.4.1.9.9.294.1.1.3 |
The number of entries currently present in the
zoneSetTable. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..8388608 |
|
zoneSetTable |
1.3.6.1.4.1.9.9.294.1.1.4 |
A table containing information on each Zone
Set which is configured and available on
any VSAN known to the local Zone Server.
The zoneSetTable lists all the zone sets
configured on all the VSANs configured on the
local zone server. There could be multiple zone
sets configured on a VSAN. But only one zone set
is allowed to be active at a time in each VSAN. A
Zone Set is a collection of zones. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneSetEntry |
|
zoneSetEntry |
1.3.6.1.4.1.9.9.294.1.1.4.1 |
An entry (conceptual row) in the zoneSetTable. The
zone sets are defined with respect to a VSAN. Hence,
this table is indexed by the vsanIndex, in addition to
the zoneSetIndex.
The sequence of operations to be performed in order
to create a zone set is as follows:
- create zone entries in the ZoneTable.
- create an entry in this table and set the
zoneSetZoneList bitmap object to contain the
required zones.
- Note that it is perfectly valid to create an
empty zone set. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneSetEntry |
|
|
zoneSetIndex |
1.3.6.1.4.1.9.9.294.1.1.4.1.1 |
The index of a zone set. This object uniquely
identifies a zone set on a particular VSAN. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
1..2048 |
|
zoneSetName |
1.3.6.1.4.1.9.9.294.1.1.4.1.2 |
The name of this zone set. The zoneSetName
should be unique within a VSAN.
The zone set can be renamed by setting this object
to a new value.
This object MUST be set before or concurrently
with setting the corresponding instance of
zoneSetRowStatus to 'active'. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
SnmpAdminString |
Size(1..64) |
|
zoneSetZoneList |
1.3.6.1.4.1.9.9.294.1.1.4.1.3 |
The set of zones which form this zone set on this
VSAN. The zones are identified by zoneIndex object
in the zoneTable.
If a particular bit has a value of '1', then the
corresponding zone is a part of this zone set.
All other zones have '0' in their positions or
not present in the string.
The default value is the zero length string. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneSetLastChange |
1.3.6.1.4.1.9.9.294.1.1.4.1.4 |
The value of sysUpTime at the time of the last
change to this zone set entry. If the entry has
not been modified since the last re-initialization
of the local network management system, then this
object will contain a zero value. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TimeStamp |
|
|
zoneSetRowStatus |
1.3.6.1.4.1.9.9.294.1.1.4.1.5 |
The status of this conceptual row.
This object can not be set to 'active' unless
the corresponding value of zoneSetName is
unique within the VSAN. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
zoneSetClone |
1.3.6.1.4.1.9.9.294.1.1.4.1.6 |
Setting this object to a name will result in
this zone set being cloned and the cloned
zone set will be set to this name.
When this object is read, the zero-length
string is returned. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
SnmpAdminString |
Size(1..64) |
|
zoneSetActivateTable |
1.3.6.1.4.1.9.9.294.1.1.5 |
This table contains atmost one entry for
each VSAN that is configured. These entries
reflect the state of the activation of a
zone set on the corresponding VSAN.
The management station needs to create an
entry in this table on the desired VSAN before
a zone set can be activated on that VSAN. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneSetActivateEntry |
|
zoneSetActivateEntry |
1.3.6.1.4.1.9.9.294.1.1.5.1 |
An entry (conceptual row) in this table. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneSetActivateEntry |
|
|
zoneSetActivate |
1.3.6.1.4.1.9.9.294.1.1.5.1.1 |
Setting this object to a value is a request for a
zone set to be activated on the particular VSAN,
i.e., for the current configuration of that zone
set to be cloned with the clone becoming the
active zone set for the particular VSAN.
Setting this object to a value (say, N) identifies
the zone set to be cloned as the zone set
identified by zoneSetIndex object having the same
value N.
Even though there could be multiple zone sets on a
VSAN, only one can be active at a time. If a zone
set is already active on a VSAN and a second zone
set is activated on the same VSAN, then the first
zone set is automatically deactivated and the second
zone set is activated.
The value of this object when read is always 0. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
1..2048 |
|
zoneSetActivateResult |
1.3.6.1.4.1.9.9.294.1.1.5.1.2 |
This object indicates the outcome of the most
recent activation/deactivation.
When the value of this object is 'inProgress',
the values of the corresponding instances of
zoneSetActivate, zoneSetDeActivate and
zoneSetActivateRowStatus cannot be modified.
The value 'newEntry' indicates that after the
entry has been created, activation/de-activation
has not yet been attempted on the entry. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
activateSuccess(1), activateFailure(2), deactivateSuccess(3), deactivateFailure(4), inProgress(5), newEntry(6) |
|
zoneSetDeActivate |
1.3.6.1.4.1.9.9.294.1.1.5.1.3 |
Setting this object to 'deactivate' is a request
to deactivate the currently active zone set on
this VSAN.
No action is taken if this object is set to
'noop'.
The value of this object when read is always
'noop'. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
INTEGER |
deactivate(1), noop(2) |
|
zoneSetFailCause |
1.3.6.1.4.1.9.9.294.1.1.5.1.5 |
The reason for the failure of the zone set
activation/de-activation.
The value of this object contains the reason
for the failure only if the value of the
corresponding instance of zoneSetActivateResult
is either 'activateFailure' or
'deactivateFailure'. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
FcChangeProtoFailCause |
|
|
zoneSetFailDomId |
1.3.6.1.4.1.9.9.294.1.1.5.1.6 |
The domain id of the device in the fabric that
has caused the Change Protocol to fail.
This object will contain a valid domain id if
the activation/deactivation has failed and the
corresponding instance of zoneSetFailCause
has a value between rcvdSfcBusy(2) and
invalidZsetFormat(11).
These errors are flagged by Zone Server modules
running on other devices in the entire fabric
as part of the Change Protocol.
The remaining errors are those that are detected
on the local Zone Server. In that case, this object
will contain the value 0. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DomainIdOrZero |
|
|
zoneNumber |
1.3.6.1.4.1.9.9.294.1.1.6 |
The number of entries currently present in the
zoneTable. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..8388608 |
|
zoneTable |
1.3.6.1.4.1.9.9.294.1.1.7 |
This table gives information on all the
zones/aliases and lists all their members. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneEntry |
|
zoneEntry |
1.3.6.1.4.1.9.9.294.1.1.7.1 |
An entry (conceptual row) in the zoneTable.
The sequence of operations to be performed in
order to create a zone is as follows:
- create an entry in this table.
- create zone members in the zoneMemberTable
that belong to this zone.
- if aliases need to be created, create an
alias entry in the zoneAliasTable, create
alias members in the zoneMemberTable and
associate the alias with the required zone
entry by setting the zoneAliasList object
in this table appropriately. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneEntry |
|
|
zoneIndex |
1.3.6.1.4.1.9.9.294.1.1.7.1.1 |
The index of a zone on this VSAN. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
1..8192 |
|
zoneName |
1.3.6.1.4.1.9.9.294.1.1.7.1.2 |
The name of this zone. The zoneName should be
unique within a VSAN.
The zone can be renamed by setting this object
to a new value.
This object MUST be set before or concurrently
with setting the corresponding instance of
zoneRowStatus to 'active'. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
SnmpAdminString |
Size(1..64) |
|
zoneMemberList |
1.3.6.1.4.1.9.9.294.1.1.7.1.3 |
The set of zone members that form this zone on
this VSAN.
The zone members are identified by zoneMemberIndex
object in the zoneMemberTable.
If a particular bit has a value of '1', then the
corresponding zone member is a part of this zone.
All other zone members have '0' in their
positions or not present in the string.
This object is read-only; changes to its value
are made by the agent as and when associated
entries are created/deleted in the
zoneMemberTable.
The default value is the zero length string. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneAliasList |
1.3.6.1.4.1.9.9.294.1.1.7.1.4 |
The set of aliases that form this zone on this
VSAN.
The aliases are identified by the zoneAliasIndex
object in the zoneAliasTable.
If a particular bit has a value of '1', then
the corresponding alias is a part of this zone.
All other aliases have '0' in their positions
or not present in the string.
The default value is the zero length string. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneLastChange |
1.3.6.1.4.1.9.9.294.1.1.7.1.5 |
The value of sysUpTime at the time of the last
change to this zone entry. If the entry has not
been modified since the last re-initialization
of the local network management system, then this
object will contain a zero value. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TimeStamp |
|
|
zoneRowStatus |
1.3.6.1.4.1.9.9.294.1.1.7.1.6 |
The status of this conceptual row.
This object can not be set to 'active'
unless the corresponding value of zoneName
is unique within the VSAN. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
zoneReadOnly |
1.3.6.1.4.1.9.9.294.1.1.7.1.7 |
This object indicates if only SCSI read
operations are allowed on the members of
this zone which are SCSI targets.
If the value of this object is set to 'true',
then only SCSI read operations are permitted.
So, this becomes a read-only zone.
If the value of this object is set to
'false', then both SCSI read and write
operations are permitted. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneQos |
1.3.6.1.4.1.9.9.294.1.1.7.1.8 |
This object specifies if qos attribute for this
zone is enabled. If this object is set to 'true',
then qos attribute for this zone is enabled.
If this object is set to 'false', then qos
attribute for this zone is disabled.
If this attribute is enabled for this zone,
then only traffic with the configured priority
level will be allowed between the members of
this zone. The priority can be specified by means
of the corresponding instance of zoneQosPriority
object. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneQosPriority |
1.3.6.1.4.1.9.9.294.1.1.7.1.9 |
Specifies the qos priority value. The value of
this object is relevant only if the corresponding
instance of zoneQos object is enabled by setting
it to 'true'. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
ZoneQosPriorityLevel |
|
|
zoneBroadcast |
1.3.6.1.4.1.9.9.294.1.1.7.1.10 |
This object specifies if broadcast zoning is
enabled on this zone. If this object is set to
'true', then it is enabled. If this object is
set to 'false', then it is disabled.
If broadcast zoning is enabled on this zone,
then broadcast frames generated by a member in this
zone will be restricted to members in this zone. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneClone |
1.3.6.1.4.1.9.9.294.1.1.7.1.11 |
Setting this object to a name will result in
this zone being cloned and the cloned
zone will be set to this name.
When this object is read, the zero-length
string is returned. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
SnmpAdminString |
Size(1..64) |
|
zoneAliasNumber |
1.3.6.1.4.1.9.9.294.1.1.8 |
The number of entries currently present in the
zoneAliasTable. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..8388608 |
|
zoneAliasTable |
1.3.6.1.4.1.9.9.294.1.1.9 |
This table gives information on all the aliases and
their members. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneAliasEntry |
|
zoneAliasEntry |
1.3.6.1.4.1.9.9.294.1.1.9.1 |
An entry (conceptual row) in this table. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneAliasEntry |
|
|
zoneAliasIndex |
1.3.6.1.4.1.9.9.294.1.1.9.1.1 |
The index of an alias entry on this VSAN. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
1..2048 |
|
zoneAliasName |
1.3.6.1.4.1.9.9.294.1.1.9.1.2 |
The name of this alias. The name of the alias
should be unique within a VSAN.
The alias can be renamed by setting this object
to a new value.
This object MUST be set before or concurrently
with setting the corresponding instance of
zoneAliasRowStatus to 'active'. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
SnmpAdminString |
Size(1..64) |
|
zoneAliasMemberList |
1.3.6.1.4.1.9.9.294.1.1.9.1.3 |
The set of zone members which form this alias
on this VSAN.
The members of an alias are identified by the
zoneMemberIndex object in the zoneMemberTable.
If a particular bit has a value of '1', then the
corresponding zone member is a part of this alias.
All other zone members have '0' in their positions
or not present in the string.
This object is read-only; changes to its value are
made by the agent as and when associated entries are
created/deleted in the zoneMemberTable.
The default value is the zero length string. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneAliasRowStatus |
1.3.6.1.4.1.9.9.294.1.1.9.1.4 |
The status of this conceptual row.
This object can not be set to 'active'
unless the corresponding value of
zoneAliasName is unique within the VSAN. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
zoneAliasLastChange |
1.3.6.1.4.1.9.9.294.1.1.9.1.5 |
The value of sysUpTime at the time of the last
change to this alias entry. If the entry has not
been modified since the last re-initialization
of the local network management system, then this
object will contain a zero value. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TimeStamp |
|
|
zoneAliasClone |
1.3.6.1.4.1.9.9.294.1.1.9.1.6 |
Setting this object to a name will result in
this alias being cloned and the cloned
alias will be set to this name.
When this object is read, the zero-length
string is returned. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
SnmpAdminString |
Size(1..64) |
|
zoneMemberNumber |
1.3.6.1.4.1.9.9.294.1.1.10 |
The number of entries currently present in the
zoneMemberTable. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..16777216 |
|
zoneMemberTable |
1.3.6.1.4.1.9.9.294.1.1.11 |
This table contains all members of a zone/alias
and information about those members. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneMemberEntry |
|
zoneMemberEntry |
1.3.6.1.4.1.9.9.294.1.1.11.1 |
An entry (conceptual row) in the zoneMemberTable.
Each entry represents the relationship between
a member and (one of) its 'parent(s)', i.e., a
zone or alias to which the member belongs, within
a particular VSAN. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneMemberEntry |
|
|
zoneMemberTypeIndex |
1.3.6.1.4.1.9.9.294.1.1.11.1.1 |
This object determines whether this member belongs
to a zone or an alias. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
INTEGER |
zone(1), alias(2) |
|
zoneMemberParentIndex |
1.3.6.1.4.1.9.9.294.1.1.11.1.2 |
This object contains the value of the index of
the zone or alias to which this member belongs to.
If the value of the corresponding instance of
zoneMemberTypeIndex is 'zone', then this object
will contain the value of the zoneIndex object of
the zone to which this member belongs to.
If the value of the corresponding instance of
zoneMemberTypeIndex is 'alias', then this object
will contain the value of the zoneAliasIndex object
of the alias to which this member belongs to. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
1..8192 |
|
zoneMemberIndex |
1.3.6.1.4.1.9.9.294.1.1.11.1.3 |
The index of this zone member on this VSAN on this
zone/alias. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
1..2048 |
|
zoneMemberID |
1.3.6.1.4.1.9.9.294.1.1.11.1.5 |
This object represents the zone/alias member ID. The
interpretation of this object depends on the
zoneMemberFormat object.
If the value of corresponding instance of
zoneMemberFormat object is 'wwn', then this object
holds an 8 octet long Port WWN.
If the value of corresponding instance of
zoneMemberFormat object is 'domainPort', then this
object contains a 2 octet value. The first octet
will represent the domain and the second octet
will represent the port.
If the value of the corresponding instance of
zoneMemberFormat object is 'fcAddr', then this
object contains the 3 octet N_Port FC-ID.
If the value of the corresponding instance of
zoneMemberFormat object is 'fwwn', then this object
contains the 8 octet Fabric Port WWN.
If the value of the corresponding instance of
zoneMemberFormat object is 'symNodeName', then
this object contains a symbolic node name which
could be of length 1 to 255 bytes.
If the value of corresponding instance of
zoneMemberFormat object is 'intf', then this
object will contain a 12 octet value which is a
concatenation of 4 octets containing an interface
index (ifIndex) encoded in network byte order, and
8 octets containing the WWN of a switch.
If the value of corresponding instance of
zoneMemberFormat object is 'domainIntf', then
this object will contain a 5 octet value which
is a concatenation of 1 octet representing the
domain and 4 octets representing an interface
index (ifIndex) encoded in network byte order.
If the value of corresponding instance of
zoneMemberFormat object is 'ipAddr', then
this object will contain a 4 octet IP address
value followed by an optional 4 octets of
subnet mask.
If the value of corresponding instance of
zoneMemberFormat object is 'ipAddrv6', then
this object will contain a 16 octet IPv6 address
value followed by an optional 4 octets of
prefix length encoded in network byte order.
If the value of the corresponding instance of
zoneMemberFormat object is 'deviceAlias', then
this object contains a Device Alias which
could be of length 1 to 64 bytes.
This object cannot be modified while the
corresponding value of zoneMemberRowStatus object
is 'active'. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(1..255) |
|
zoneMemberLunID |
1.3.6.1.4.1.9.9.294.1.1.11.1.6 |
This object specifies the Lun ID if Lun
zoning is configured.
If this object is the zero-length string, then
Lun zoning is not configured.
Lun zoning cannot be configured when the
corresponding instance of zoneMemberFormat
object has a value of 'fwwn', 'intf' or
'symNodeName'.
This object cannot be modified while the
corresponding value of zoneMemberRowStatus object
is 'active'. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0|8) |
|
zoneMemberRowStatus |
1.3.6.1.4.1.9.9.294.1.1.11.1.7 |
The status of this conceptual row.
zoneMemberID and zoneMemberFormat objects MUST
be set before or concurrently with setting the
corresponding instance of zoneMemberRowStatus
to 'active'. If Lun zoning needs to be configured,
then zoneMemberLunID object also needs to be set
before or concurrently with setting the
corresponding instance of zoneMemberRowStatus to
'active'. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
zoneEnforcedZoneSetNumber |
1.3.6.1.4.1.9.9.294.1.1.12 |
The number of entries currently present in the
zoneEnforcedZoneSetTable. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..2048 |
|
zoneEnforcedZoneSetTable |
1.3.6.1.4.1.9.9.294.1.1.13 |
A table containing information on all currently
enforced zone sets (active zone sets) on all VSANs.
Only one zone set can be activated per VSAN. The
active zone set is one which is copied from the
zone set database (zoneSetTable) at the time it
was activated. This active zone set is then
enforced on the fabric. This active zone set
cannot be modified.
Note that this table will be empty when no zone set
is activated. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneEnforcedZoneSetEntry |
|
zoneEnforcedZoneSetEntry |
1.3.6.1.4.1.9.9.294.1.1.13.1 |
An entry (conceptual row) in the
zoneEnforcedZoneSetTable. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneEnforcedZoneSetEntry |
|
|
zoneEnforcedZoneSetZoneList |
1.3.6.1.4.1.9.9.294.1.1.13.1.2 |
The set of zones which form this zone set on
this VSAN. This object was copied from the
zoneSetZoneList object in the zoneSetTable at
the time when the currently active zone set was
activated. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneEnforcedZoneSetActivateTime |
1.3.6.1.4.1.9.9.294.1.1.13.1.3 |
The sysUpTime at which this entry was
most recently activated. If this entry has
been activated prior to the last
re-initialization of the local network
management system, then this object will
contain a zero value. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TimeStamp |
|
|
zoneEnforcedZoneNumber |
1.3.6.1.4.1.9.9.294.1.1.14 |
The number of entries currently present in the
zoneEnforcedZoneTable. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..8388608 |
|
zoneEnforcedZoneTable |
1.3.6.1.4.1.9.9.294.1.1.15 |
This table contains all the zones/aliases that are
present in the active zone sets on all VSANs. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneEnforcedZoneEntry |
|
zoneEnforcedZoneEntry |
1.3.6.1.4.1.9.9.294.1.1.15.1 |
An entry (conceptual row) in this table. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneEnforcedZoneEntry |
|
|
zoneEnforcedZoneMemberList |
1.3.6.1.4.1.9.9.294.1.1.15.1.2 |
The set of members that form this zone on this
VSAN. This object was copied from the zoneMemberList
object in the zoneTable at the time when the
currently active zone set was activated. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneEnforcedZoneAliasList |
1.3.6.1.4.1.9.9.294.1.1.15.1.3 |
The set of aliases that form this zone on this
VSAN. This object was copied from the zoneAliasList
object in the zoneTable at the time when the
currently active zone set was activated. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneEnforcedZoneActivateTime |
1.3.6.1.4.1.9.9.294.1.1.15.1.4 |
The sysUpTime at which this entry was
most recently activated. If this entry has
been activated prior to the last
re-initialization of the local network
management system, then this object will
contain a zero value. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TimeStamp |
|
|
zoneEnforcedZoneReadOnly |
1.3.6.1.4.1.9.9.294.1.1.15.1.5 |
This object indicates whether this is a
read-only zone. This object was copied from
the zoneReadOnly object in the zoneTable at
the time when the currently active zone set
was activated. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneEnforcedZoneQos |
1.3.6.1.4.1.9.9.294.1.1.15.1.6 |
This object indicates whether this is a
qos enabled zone. This object was copied from
the zoneQos object in the zoneTable at
the time when the currently active zone set
was activated. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneEnforcedZoneQosPriority |
1.3.6.1.4.1.9.9.294.1.1.15.1.7 |
This object indicates the priority of qos
if it is a qos enabled zone. This object was
copied from the zoneQosPriority object in the
zoneTable at the time when the currently active
zone set was activated. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
ZoneQosPriorityLevel |
|
|
zoneEnforcedZoneBroadcast |
1.3.6.1.4.1.9.9.294.1.1.15.1.8 |
This object indicates whether broadcast zoning is
enabled. This object was copied from the
zoneBroadcast object in the zoneTable at
the time when the currently active zone set
was activated. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneEnforcedZoneAliasNumber |
1.3.6.1.4.1.9.9.294.1.1.16 |
The number of entries currently present in the
zoneEnforcedZoneAliasTable. |
Status: deprecated |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..8488608 |
|
zoneEnforcedZoneAliasEntry |
1.3.6.1.4.1.9.9.294.1.1.17.1 |
An entry (conceptual row) in this table. |
Status: deprecated |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneEnforcedZoneAliasEntry |
|
|
zoneEnforcedZoneAliasMemberList |
1.3.6.1.4.1.9.9.294.1.1.17.1.2 |
The set of members that form this alias on this
VSAN. This object was copied from the
zoneAliasMemberList object in the zoneAliasTable at
the time when the currently active zone set was
activated. |
Status: deprecated |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneEnforcedZoneMemberNumber |
1.3.6.1.4.1.9.9.294.1.1.18 |
The number of entries currently present in the
zoneEnforcedZoneMemberTable. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..16777216 |
|
zoneEnforcedZoneMemberEntry |
1.3.6.1.4.1.9.9.294.1.1.19.1 |
An entry (conceptual row) in this table. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneEnforcedZoneMemberEntry |
|
|
zoneEnforcedZoneMemberID |
1.3.6.1.4.1.9.9.294.1.1.19.1.2 |
This object represents this member's address.
This object was copied from the zoneMemberID
object in the zoneMemberTable at the time when
the currently active zone set was activated. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(1..255) |
|
zoneEnforcedZoneMemberLunID |
1.3.6.1.4.1.9.9.294.1.1.19.1.3 |
This object specifies the Lun ID if LUN
zoning is configured. This object was copied
from the zoneMemberLunID object in the
zoneMemberTable at the time when the currently
active zone set was activated. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0|8) |
|
zoneMergeFailRecoverSpinLock |
1.3.6.1.4.1.9.9.294.1.1.20 |
This object is used to facilitate modification
of zoneMergeFailRecoverInterface,
zoneMergeFailRecoverVsan and
zoneMergeFailRecoverOper by multiple managers.
The procedure for modifying these objects is
as follows:
1. Determine new values for
zoneMergeFailRecoverInterface, zoneMergeFail-
RecoverVsan and zoneMergeFailRecoverOper.
2. Retrieve the value of zoneMergeFailRecoverSpinLock.
3. Set the value of zoneMergeFailRecoverSpinLock to
the retrieved value, and (in the same PDU) the value
of zoneMergeFailRecoverInterface to the new
value. If the set fails for
zoneMergeFailRecoverSpinLock object, go back to step
2.
4. Set the value of zoneMergeFailRecoverSpinLock to
the retrieved value plus one, and (in the same PDU)
the value of zoneMergeFailRecoverVsan to the new
value. If the set fails for
zoneMergeFailRecoverSpinLock object, go back to step
2.
5. Set the value of zoneMergeFailRecoverSpinLock to
the retrieved value plus two, and (in the same PDU)
the value of zoneMergeFailRecoverOper to the new
value. If the set fails for
zoneMergeFailRecoverSpinLock object, go back to step
2.
Note that if it's possible to include
zoneMergeFailRecoverVsan and/or
zoneMergeFailRecoverOper in the (Set Req) PDU
of an earlier step, then steps 4 and/or 5 can
be eliminated. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TestAndIncr |
|
|
zoneMergeFailRecoverInterface |
1.3.6.1.4.1.9.9.294.1.1.21 |
The interface on which the Merge Failure Recovery
needs to be carried out. The value of this object
before the first set operation will be zero. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
InterfaceIndexOrZero |
|
|
zoneMergeFailRecoverVsan |
1.3.6.1.4.1.9.9.294.1.1.22 |
The VSAN on which the Merge Failure Recovery
needs to be carried out. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
VsanIndex |
|
|
zoneMergeFailRecoverOper |
1.3.6.1.4.1.9.9.294.1.1.23 |
The operation to be carried out.
If this object is set to 'import', then the
Active Zone Set from across the isolated link
is imported.
If this object is set to 'export', then the
Active Zone Set on the local system is
exported across the isolated link.
No action is taken if this object is set
to 'noop'.
The value of this object when read is always
'noop'. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
import(1), export(2), noop(3) |
|
zoneMergeFailRecoverResult |
1.3.6.1.4.1.9.9.294.1.1.24 |
The result of the last Merge Failure Recovery
operation that was attempted.
If the value of this object is 'success', then
the merge fail recovery operation was
successful.
If the value of this object is 'failure', then
the merge fail recovery operation failed.
If the value of this object is 'inProgress',
then the merge fail recovery operation is
still in progress. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
success(1), failure(2), inProgress(3) |
|
zoneCopyActiveToFullOnVsan |
1.3.6.1.4.1.9.9.294.1.1.25 |
The VSAN on which the enforced zone set
(active zone set) needs to be copied to the
zone set database (full zone set). Setting
this object to a valid VSAN will trigger a
copy of the enforced zone set on that VSAN
to the zone set database on the same VSAN.
Setting this object to an invalid VSAN-id
will result in an error and no copy will
take place. |
Status: deprecated |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
VsanIndex |
|
|
zoneTotalGS3Rejects |
1.3.6.1.4.1.9.9.294.1.2.1 |
The total number of GS3 requests rejected
by this Zone Server across all VSANs. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneStatsTable |
1.3.6.1.4.1.9.9.294.1.2.2 |
This table contains statistic counters which are
maintained by the Zone Server. These counters are
maintained per VSAN. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneStatsEntry |
|
zoneStatsEntry |
1.3.6.1.4.1.9.9.294.1.2.2.1 |
An entry (conceptual row) in this table. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneStatsEntry |
|
|
zoneTxMergeReqs |
1.3.6.1.4.1.9.9.294.1.2.2.1.1 |
The number of Merge Request Frames sent by this
Zone Server to other Zone Servers in the fabric
on this VSAN. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneRxMergeAccepts |
1.3.6.1.4.1.9.9.294.1.2.2.1.2 |
The number of Merge Accept Frames received by this
Zone Server from other Zone Servers in the fabric on
this VSAN. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneRxMergeReqs |
1.3.6.1.4.1.9.9.294.1.2.2.1.3 |
The number of Merge Request Frames received by this
Zone Server from other Zone Servers in the fabric on
this VSAN. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneTxMergeAccepts |
1.3.6.1.4.1.9.9.294.1.2.2.1.4 |
The number of Merge Accept Frames sent by this
Zone Server to other Zone Servers in the fabric on
this VSAN. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneTxChangeReqs |
1.3.6.1.4.1.9.9.294.1.2.2.1.5 |
The number of Change Requests sent by this Zone
Server to other Zone Servers in the fabric on
this VSAN.
This includes Acquire Change Authorization
requests, Stage Fabric Config Update requests,
Update Fabric Config requests and Release Change
Authorization requests. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneRxChangeAccepts |
1.3.6.1.4.1.9.9.294.1.2.2.1.6 |
The number of Change Responses received by this
Zone Server from other Zone Servers in the fabric
on this VSAN.
This includes Acquire Change Authorization Accept,
Stage Fabric Config Update Accept, Update Fabric
Config Accept and Release Change Authorization
Accept frames. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneRxChangeReqs |
1.3.6.1.4.1.9.9.294.1.2.2.1.7 |
The number of Change Requests received by this
Zone Server from other Zone Servers in the fabric
on this VSAN.
This includes Acquire Change Authorization requests,
Stage Fabric Config Update requests, Update Fabric
Config requests and Release Change Authorization
requests. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneTxChangeAccepts |
1.3.6.1.4.1.9.9.294.1.2.2.1.8 |
The number of Change Responses sent by this
Zone Server to other Zone Servers in the fabric
on this VSAN.
This includes Acquire Change Authorization Accept,
Stage Fabric Config Update Accept, Update Fabric
Config Accept and Release Change Authorization
Accept frames. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneRxGS3Reqs |
1.3.6.1.4.1.9.9.294.1.2.2.1.9 |
The number of GS3 requests received by this Zone
Server on this VSAN. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneTxGS3Rejects |
1.3.6.1.4.1.9.9.294.1.2.2.1.10 |
The number of GS3 requests rejected by this Zone
Server on this VSAN. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneLunStatsTable |
1.3.6.1.4.1.9.9.294.1.2.3 |
This table contains statistic counters related to
LUNs. These counters are populated by the local
Zone Server based on SCSI frames that are
forwarded to it because the LUNs being accessed
have been zoned out from a initiator's list of
accessible LUNs.
These counters are maintained per VSAN, per SCSI
initiator-target pair, per LUN. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneLunStatsEntry |
|
zoneLunStatsEntry |
1.3.6.1.4.1.9.9.294.1.2.3.1 |
Each entry provides SCSI statistics, at the local
Zone Server, for the host identified by
zoneLunSrcFcId trying to access the LUN
identified by zoneLunNum, that has
been zoned out from zoneLunSrcFcId's list of
accessible LUNs, on the disk identified by
zoneLunDstFcId on the VSAN identified by
vsanIndex. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneLunStatsEntry |
|
|
zoneLunSrcFcId |
1.3.6.1.4.1.9.9.294.1.2.3.1.1 |
The FC-ID of a SCSI initiator that is
accessing a LUN identified by
zoneLunNum. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
FcAddressId |
|
|
zoneLunDstFcId |
1.3.6.1.4.1.9.9.294.1.2.3.1.2 |
The FC-ID of a SCSI target containing the
LUN identified by zoneLunNum. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
FcAddressId |
|
|
zoneLunNum |
1.3.6.1.4.1.9.9.294.1.2.3.1.3 |
The LUN that is being accessed. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(8) |
|
zoneLunRxInqReqs |
1.3.6.1.4.1.9.9.294.1.2.3.1.4 |
The number of SCSI INQUIRY commands that have
been received by the local Zone Server from the
SCSI initiator zoneLunSrcFcId to the SCSI
target zoneLunDstFcId for the LUN
zoneLunNum, on the VSAN vsanIndex. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneLunRxRepLunReqs |
1.3.6.1.4.1.9.9.294.1.2.3.1.5 |
The number of SCSI Report LUNs commands that
have been received by the local Zone Server from
the SCSI initiator zoneLunSrcFcId to the SCSI
target zoneLunDstFcId for the LUN
zoneLunNum, on the VSAN vsanIndex.
Typically the Report LUNs command is sent only
for LUN 0. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneLunRxSenseReqs |
1.3.6.1.4.1.9.9.294.1.2.3.1.6 |
The number of SCSI SENSE commands that have
been received by the local Zone Server from the
SCSI initiator zoneLunSrcFcId to the SCSI
target zoneLunDstFcId for the LUN
zoneLunNum, on the VSAN vsanIndex. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneLunRxOtherCmds |
1.3.6.1.4.1.9.9.294.1.2.3.1.7 |
The number of SCSI Read, Write, Seek etc.
commands received by the local Zone Server from
the SCSI initiator zoneLunSrcFcId to the SCSI
target zoneLunDstFcId for the LUN
zoneLunNum, on the VSAN vsanIndex, during
changes to the zoning configuration. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneLunTxInqDataNoLus |
1.3.6.1.4.1.9.9.294.1.2.3.1.8 |
The number of 'No LU' error responses sent by the
local Zone Server in response to SCSI INQUIRY
commands from the SCSI initiator zoneLunSrcFcId
to the SCSI target zoneLunDstFcId for the LUN
zoneLunNum, on the VSAN vsanIndex. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneLunTxIllegalReqs |
1.3.6.1.4.1.9.9.294.1.2.3.1.9 |
The number of 'Illegal Request Check Condition'
responses sent by the local Zone Server in
response to SCSI commands from the SCSI
initiator zoneLunSrcFcId to the SCSI target
zoneLunDstFcId for the LUN zoneLunNum, on
the VSAN vsanIndex. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneRoZoneStatsTable |
1.3.6.1.4.1.9.9.294.1.2.4 |
This table contains statistic counter(s) related
to read-only zones which are maintained by the
Zone Server. These counters are maintained per
VSAN, per SCSI initiator target pair, per LUN. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneRoZoneStatsEntry |
|
zoneRoZoneStatsEntry |
1.3.6.1.4.1.9.9.294.1.2.4.1 |
Each entry provides statistics for the host
identified by zoneRoZoneSrcFcId accessing the LUN
identified by zoneRoZoneLunNum on the disk
identified by zoneRoZoneDstFcId on the VSAN
identified by vsanIndex. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneRoZoneStatsEntry |
|
|
zoneRoZoneSrcFcId |
1.3.6.1.4.1.9.9.294.1.2.4.1.1 |
The FC-ID of a SCSI initiator that is
accessing a LUN identified by
zoneRoZoneLunNum. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
FcAddressId |
|
|
zoneRoZoneDstFcId |
1.3.6.1.4.1.9.9.294.1.2.4.1.2 |
The FC-ID of a SCSI target containing the
LUN identified by zoneRoZoneLunNum. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
FcAddressId |
|
|
zoneRoZoneLunNum |
1.3.6.1.4.1.9.9.294.1.2.4.1.3 |
The LUN that is being accessed. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(8) |
|
zoneRoZoneTxDataProts |
1.3.6.1.4.1.9.9.294.1.2.4.1.4 |
The number of 'Data protected Check Condition'
error responses sent by the local Zone Server,
when the SCSI initiator identified by
zoneRoZoneSrcFcId tries to modify a LUN identified
by zoneRoZoneLunNum on the SCSI target
zoneRoZoneDstFcId. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Counter32 |
|
|
zoneServiceRejReasonCodeExp |
1.3.6.1.4.1.9.9.294.1.3.2 |
This object contains the reason code explanation
if the reason code is 'Unable to perform command
req'. This object also corresponds to the latest
Zone Server request rejection. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
FcZoneServerRejReasonExpl |
|
|
zoneMergeFailureVSANNum |
1.3.6.1.4.1.9.9.294.1.3.3 |
This object contains the number of the VSAN on an
interface on which the last zone merge failed.
If the zone merge has failed on all VSANs, then this
object will contain the value of 0. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
0..4096 |
|
zoneMergeSuccessVSANNum |
1.3.6.1.4.1.9.9.294.1.3.4 |
This object contains the number of the VSAN on an
interface on which the last zone merge succeeded.
If the zone merge has succeeded on all VSANs, then
this object will contain the value of 0. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
0..4096 |
|
zoneMergeFailureObject |
1.3.6.1.4.1.9.9.294.1.3.5 |
This object contains the name of the zoning
database object which was the cause of the
merge failure. In cases where it is not
applicable, this object will contain the
null string. |
Status: current |
Access: accessible-for-notify |
OBJECT-TYPE |
|
|
|
|
SnmpAdminString |
|
|
zoneServiceReqRejNotifyEnable |
1.3.6.1.4.1.9.9.294.1.1.26 |
This object specifies if the Zone Server should
issue a 'zoneServiceReqRejNotify' notification.
If the value of this object is 'true', then the
notification is issued.
If the value of this object is 'false', then the
notification is not issued. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneMergeFailureNotifyEnable |
1.3.6.1.4.1.9.9.294.1.1.27 |
This object specifies if the zone server should
issue a zoneMergeFailureNotify notification.
If the value of this object is 'true', then the
notification is issued.
If the value of this object is 'false', then the
notification is not issued. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneMergeSuccessNotifyEnable |
1.3.6.1.4.1.9.9.294.1.1.28 |
This object specifies if the zone server should
issue a zoneMergeSuccessNotify notification.
If the value of this object is 'true', then the
notification is issued.
If the value of this object is 'false', then the
notification is not issued. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneDefZoneBehvrChngNotifyEnable |
1.3.6.1.4.1.9.9.294.1.1.29 |
This object specifies if the zone server should
issue a zoneDefZoneBehaviourChngNotify
notification.
If the value of this object is 'true', then the
notification is issued.
If the value of this object is 'false', then the
notification is not issued. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneDbTable |
1.3.6.1.4.1.9.9.294.1.1.30 |
This table contains one entry for each VSAN
that is configured. These entries provide the
capability to perform operations on the local
zone server database on a VSAN. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneDbEntry |
|
zoneDbEntry |
1.3.6.1.4.1.9.9.294.1.1.30.1 |
An entry (conceptual row) in this table. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneDbEntry |
|
|
zoneDbClearDb |
1.3.6.1.4.1.9.9.294.1.1.30.1.1 |
Setting this object to 'clear(1)', will result
in the local zone server database being deleted
on this VSAN.
Setting this object to 'noop(2)', results in
no action.
When read, the value of this object is always
'noop(2)'. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
clear(1), noop(2) |
|
zoneDbEnforcedEqualsLocal |
1.3.6.1.4.1.9.9.294.1.1.30.1.2 |
This object indicates if the enforced database
is the same as the local database on this VSAN.
If the value of this object is 'true', then they
are the same.
If the value of this object is 'false', then
they are not the same. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneDbHardZoningEnabled |
1.3.6.1.4.1.9.9.294.1.1.30.1.3 |
This object indicates if hard zoning is
enabled on this VSAN. Hard Zoning is a
mechanism by which zoning is enforced in
hardware.
If the value of this object is 'true', then
hard zoning is enabled on this VSAN.
If the value of this object is 'false', then
hard zoning is not enabled on this VSAN. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneCopyTable |
1.3.6.1.4.1.9.9.294.1.1.31 |
In this table, for each VSAN that is configured,
atmost one entry can be created. These entries
provide the capability to copy the active zone set
on a VSAN to a file on the local device and/or to
a remote device over the network.
At any point of time, only one copy operation
can be active for all the VSANs. If a second
copy is attempted, it will result in error. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneCopyEntry |
|
zoneCopyEntry |
1.3.6.1.4.1.9.9.294.1.1.31.1 |
An entry (conceptual row) in this table. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneCopyEntry |
|
|
zoneCopyProto |
1.3.6.1.4.1.9.9.294.1.1.31.1.1 |
The protocol to be used for the copy of
the active zone set on this VSAN. If the
copy needs to take place on the local device,
then the value of this object will be ignored. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
ZoneCopyProtocol |
|
|
zoneCopyDestFileType |
1.3.6.1.4.1.9.9.294.1.1.31.1.2 |
The type of file to which the active zoneset
needs to be copied.
If the value of this object is set to
'networkFile(1)', then values must be set for
the corresponding instances of zoneCopyServerAddr
and zoneCopyDestFileName objects.
If the value of this object is set to
'localFile(2)', then the corresponding instance
of zoneCopyDestFileName must be set. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
ZoneFileType |
|
|
zoneCopyServerAddrType |
1.3.6.1.4.1.9.9.294.1.1.31.1.3 |
The type of address of the remote device as
specified by the corresponding instance of
zoneCopyServerAddr object. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
InetAddressType |
|
|
zoneCopyServerAddr |
1.3.6.1.4.1.9.9.294.1.1.31.1.4 |
The ip address of the remote device to which
the active zoneset on this VSAN needs to be
copied. This object must be set to a valid
value when the corresponding instance of
zoneCopyDestFileType is set to 'networkFile'
before the copy can be initiated by means
of the zoneCopyStartCopy object.
The protocol to be used for the copy operation
is specified by the value of the
corresponding instance of zoneCopyProto
object. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
InetAddress |
|
|
zoneCopyDestFileName |
1.3.6.1.4.1.9.9.294.1.1.31.1.5 |
The file-name, including the full path,
of the file to which the active zoneset
on this VSAN needs to be copied.
This object must be set to a valid value
before the copy can be initiated by means
of the zoneCopyStartCopy object. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
SnmpAdminString |
Size(1..255) |
|
zoneCopyUserName |
1.3.6.1.4.1.9.9.294.1.1.31.1.6 |
The user name on the remote device onto
which the active zoneset on this VSAN
needs to be copied. This object needs to
be set only if the value of the
corresponding instance of zoneCopyDestFileType
object is 'networkFile'. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
SnmpAdminString |
Size(0..32) |
|
zoneCopyUserPassword |
1.3.6.1.4.1.9.9.294.1.1.31.1.7 |
The password corresponding to the user
name specified by zoneCopyUserName object
on the remote device. This object is
meaningful only if the corresponding
instance of zoneCopyDestFileType object is
'networkFile' and the protocol to be
used as specified by zoneCopyProto is
'ftp' or 'sftp' or 'scp'.
The value of this object when read is
always the zero length string for
security reasons. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
SnmpAdminString |
Size(0..32) |
|
zoneCopyStartCopy |
1.3.6.1.4.1.9.9.294.1.1.31.1.8 |
This object provides the capability to
start the copy operation of the active
zoneset on this VSAN to the desired
destination.
When set to 'copy(1)', the copy of the
active zoneset on this VSAN is started.
No action is taken if this object is set
to 'noop(2)'.
The value of this object when read is
always 'noop'. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
INTEGER |
copy(1), noop(2) |
|
zoneCopyState |
1.3.6.1.4.1.9.9.294.1.1.31.1.9 |
The result of the most recent copy operation
on this VSAN.
success(1) - indicates that the copy
operation was successful.
timeout(2) - indicates that the copy operation
failed due to a timeout.
badFileName(3) - indicates that the file name/
path/permissions are incorrect.
inProgress(4) - indicates that this copy
operation is currently in
progress.
badUserNamePasswd(5) - indicates that the user
name/password of the
remote device is incorrect.
incompleteConfig(6) - configuration is
incomplete.
unknown(7) - error is unknown.
sysErr(8) - system error
anotherCopyInProgress(9) - indicates that a
copy operation on the
same VSAN or another
VSAN is already
in progress. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
success(1), timeout(2), badFileName(3), inProgress(4), badUserNamePasswd(5), incompleteConfig(6), unknown(7), sysErr(8), anotherCopyInProgress(9) |
|
zoneCopyRowStatus |
1.3.6.1.4.1.9.9.294.1.1.31.1.10 |
The status of this conceptual row. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
zoneUnsuppMemInIntOpNotifyEnable |
1.3.6.1.4.1.9.9.294.1.1.32 |
This object specifies if the zone server should
issue a zoneUnsuppMemInIntOpModeNotify
notification.
If the value of this object is 'true', then the
notification is issued.
If the value of this object is 'false', then the
notification is not issued. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
zoneVsanId |
1.3.6.1.4.1.9.9.294.1.1.33 |
This object represents the VSAN id on which a
mismatch between the operating mode of the local
switch and the type of zone members has been
detected. |
Status: current |
Access: accessible-for-notify |
OBJECT-TYPE |
|
|
|
|
VsanIndex |
|
|
zoneZoneSetDistributeVsan |
1.3.6.1.4.1.9.9.294.1.1.34 |
This object represents the VSAN on which the
full zoneset information needs to be
distributed throughout the fabric. Setting this
object to a valid VSAN will trigger such an
operation. Setting this object to an invalid
VSAN will result in an error and no action will
be taken.
It is to be noted that this operation of full
zoneset distribution on this VSAN is done
immediately and this is independent of
activation/deactivation.
This is supported only in 'interop' modes 2 and
3.
When a full zoneset distribute operation is
in process on a VSAN, any attempt to start the
same on another VSAN will result in error. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
VsanIndex |
|
|
zoneZoneSetDistributeResult |
1.3.6.1.4.1.9.9.294.1.1.35 |
The outcome of the full zoneset distribute
operation on the VSAN indicated by
zoneZoneSetDistributeVsan object. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
success(1), failure(2), inProgress(3) |
|
zoneZoneSetDistributeFailReason |
1.3.6.1.4.1.9.9.294.1.1.36 |
If the outcome of distributing the full
zoneset on a VSAN is failure, then this
object will contain the reason for the
failure. In other cases, the value of
this object does not make sense. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
FcChangeProtoFailCause |
|
|
zoneSwitchWwn |
1.3.6.1.4.1.9.9.294.1.1.37 |
This object represents the WWN of the
local device. It is used in the
notification zoneActivateNotify. |
Status: current |
Access: accessible-for-notify |
OBJECT-TYPE |
|
|
|
|
FcNameId |
|
|
zoneSetZoneListTable |
1.3.6.1.4.1.9.9.294.1.1.38 |
This table is an extension to the
zoneSetTable defined above.
The object zoneSetZoneList in zoneSetTable
represents the set of zones that form a
zoneset. However, this object has the
limitation of being able to represent
only 2048 zones. This table which extends
the zoneSetTable overcomes this limitation
and the number of zones that form a
zoneset is increased to 8192. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneSetZoneListEntry |
|
zoneSetZoneListEntry |
1.3.6.1.4.1.9.9.294.1.1.38.1 |
An entry (conceptual row) in this table
represents a set of 6144 zones that can be
associated with the zoneset represented by
zoneSetIndex on VSAN represented by
vsanIndex. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneSetZoneListEntry |
|
|
zoneSetZoneListBmap4k |
1.3.6.1.4.1.9.9.294.1.1.38.1.1 |
The set of zones from ids 2049 to 4096 which form
this zone set on this VSAN. The zones are
identified by zoneIndex object in the
zoneTable.
If a particular bit has a value of '1', then the
corresponding zone is a part of this zone set.
All other zones have '0' in their positions or
not present in the string.
The default value is the zero length string. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneSetZoneListBmap6k |
1.3.6.1.4.1.9.9.294.1.1.38.1.2 |
The set of zones from ids 4097 to 6144 which form
this zone set on this VSAN. The zones are
identified by zoneIndex object in the
zoneTable.
If a particular bit has a value of '1', then the
corresponding zone is a part of this zone set.
All other zones have '0' in their positions or
not present in the string.
The default value is the zero length string. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneSetZoneListBmap8k |
1.3.6.1.4.1.9.9.294.1.1.38.1.3 |
The set of zones from ids 6145 to 8192 which form
this zone set on this VSAN. The zones are
identified by zoneIndex object in the
zoneTable.
If a particular bit has a value of '1', then the
corresponding zone is a part of this zone set.
All other zones have '0' in their positions or
not present in the string.
The default value is the zero length string. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneSetEnforcedZoneListTable |
1.3.6.1.4.1.9.9.294.1.1.39 |
This table is an extension to the
zoneEnforcedZoneSetTable defined above.
The object zoneEnforcedZoneSetZoneList in
zoneEnforcedZoneSetTable represents the
set of enforced zones that form an
enforced zoneset. However, this object has the
limitation of being able to represent
only 2048 zones. This table which extends
the zoneEnforcedZoneSetTable overcomes this
limitation and the number of enforced zones that
form an enforced zoneset is increased to
8192. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneSetEnforcedZoneListEntry |
|
zoneSetEnforcedZoneListEntry |
1.3.6.1.4.1.9.9.294.1.1.39.1 |
An entry (conceptual row) in this table
represents a set of upto 6144 enforced zones
that can be associated with the enforced
zoneset on VSAN represented by vsanIndex. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneSetEnforcedZoneListEntry |
|
|
zoneSetEnforcedZoneListBmap4k |
1.3.6.1.4.1.9.9.294.1.1.39.1.1 |
The set of zones from ids 2049 to 4096 which form
the enforced zone set on this VSAN. The enforced
zones are identified by zoneIndex object in the
zoneEnforcedZoneTable.
If a particular bit has a value of '1', then the
corresponding zone is a part of this zone set.
All other zones have '0' in their positions or
not present in the string. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneSetEnforcedZoneListBmap6k |
1.3.6.1.4.1.9.9.294.1.1.39.1.2 |
The set of zones from ids 4097 to 6144 which form
the enforced zone set on this VSAN. The enforced
zones are identified by zoneIndex object in the
zoneEnforcedZoneTable.
If a particular bit has a value of '1', then the
corresponding zone is a part of this zone set.
All other zones have '0' in their positions or
not present in the string. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneSetEnforcedZoneListBmap8k |
1.3.6.1.4.1.9.9.294.1.1.39.1.3 |
The set of zones from ids 6145 to 8192 which form
the enforced zone set on this VSAN. The enforced
zones are identified by zoneIndex object in the
zoneEnforcedZoneTable.
If a particular bit has a value of '1', then the
corresponding zone is a part of this zone set.
All other zones have '0' in their positions or
not present in the string. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
FcList |
|
|
zoneCompactTable |
1.3.6.1.4.1.9.9.294.1.1.40 |
The zoneSetZoneList object and the
zoneSetZoneListTable allow upto 8192
zones to be associated with a zoneset.
This is done with the help of 4 bitmaps
each of which represent 2048 zones. There
may exist a situation where the 'lowest'
bitmap may not be fully populated but
'higher' bitmaps may have bits set in them.
Semantically what this means is: the lowest
2048 zones have not been fully associated,
but zones with higher ids have been
associated. This kind of a situation causes
problems for management stations which are
only aware of older versions of this MIB. They
are only aware of zoneSetZoneList object and
hence only the 'lowest' 2048 zones that are
associated with a zoneset. In the above
situation, the total number of zones
associated with the zoneset could be less
than 2048. But by virtue of being distributed
in the 'higher' bitmaps, those zones will
not be seen by those management stations as
they are not aware of the new objects in
zoneSetZoneListTable. In such a situation,
a management station which is aware of this
version of the MIB, can choose to compact
the zones associated with zonesets on a
VSAN, so that the holes in the lowest 2048
zones are filled.
Note that this table facilitates compaction
of only the first 2048 zones and not zones
belonging to 'higher' bitmaps. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
ZoneCompactEntry |
|
zoneCompactEntry |
1.3.6.1.4.1.9.9.294.1.1.40.1 |
An entry allows compaction to be carried
out on a VSAN. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ZoneCompactEntry |
|
|
zoneCompactFirst2k |
1.3.6.1.4.1.9.9.294.1.1.40.1.1 |
Setting this object to 'compact' will
result in compaction of the lowest
2048 zones that are associated to
zonesets on this VSAN. Zones present
in higher bitmaps will be moved down
so that the holes in the lowest 2048
zones are filled. As a result of this,
the ids of the corresponding zones are
changed and a management station should
re-read the zoneTable. If such a
compaction is not possible or the
lowest 2048 zones are already compacted,
the SET operation will result in error.
If a compaction operation goes through
successfully, then the notification
zoneCompactNotify is generated.
Setting this object to 'noop', will
result in no action being taken.
The value of this object when read is
always 'noop'. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
compact(1), noop(2) |
|
zoneCompactVsan |
1.3.6.1.4.1.9.9.294.1.1.41 |
This object represents the VSAN on which
a successful zone compaction has taken place.
It is used in the notification
zoneCompactNotify. |
Status: current |
Access: accessible-for-notify |
OBJECT-TYPE |
|
|
|
|
VsanIndex |
|
|
zoneCopyActToFullSpinLock |
1.3.6.1.4.1.9.9.294.1.1.42 |
This object is used to facilitate modification
of zoneCopyActToFullMode and zoneCopyActToFullOnVsan
by multiple managers.
The procedure for modifying these objects is
as follows:
1. Determine new values for
zoneCopyActToFullMode, zoneCopyActToFullOnVsan.
2. Retrieve the value of zoneCopyActToFullSpinLock.
3. Set the value of zoneCopyActToFullSpinLock to
the retrieved value, and (in the same PDU) the value
of zoneCopyActToFullMode to the new
value. If the set fails for zoneCopyActToFullSpinLock,
go back to step 2.
4. Set the value of zoneCopyActToFullSpinLock to
the retrieved value plus one, and (in the same PDU)
the value of zoneCopyActToFullOnVsan to the new
value. If the set fails for
zoneCopyActToFullSpinLock object, go back to step
2.
Note that if it's possible to include
zoneCopyActToFullOnVsan in the (Set Req)
PDU of the earlier step, then step 4 can be
eliminated. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TestAndIncr |
|
|
zoneCopyActToFullMode |
1.3.6.1.4.1.9.9.294.1.1.43 |
Setting this object to 'includeAutoZones', results
in certain internal zones created by Zone Server being
copied along with the enforced database to the full
zoneset database.
Setting this object to 'excludeAutoZones', does not
copy those zones.
Setting this object to 'noop' results in no action
being taken.
The value of this object when read is always
'noop'. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
includeAutoZones(1), excludeAutoZones(2), noop(3) |
|
zoneCopyActToFullVsan |
1.3.6.1.4.1.9.9.294.1.1.44 |
The VSAN on which the enforced zone set
(active zone set) needs to be copied to the
zone set database (full zone set). Setting
this object to a valid VSAN will trigger a
copy of the enforced zone set on that VSAN
to the zone set database on the same VSAN.
Setting this object to an invalid VSAN-id
will result in an error and no copy will
take place. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
VsanIndex |
|
|
zoneServiceReqRejNotify |
1.3.6.1.4.1.9.9.294.1.4.0.1 |
This notification is generated whenever the local
Zone Server rejects a registration request.
The Zone Server should update the
zoneServiceRejReasonCode and zoneServiceRejReason-
CodeExp objects with the corresponding reason
code and reason code explanation before sending the
notification.
The zoneMemberType and zoneMemberID identify the
source of the request. |
Status: current |
Access: read-write |
NOTIFICATION-TYPE |
|
|
|
zoneMergeFailureNotify |
1.3.6.1.4.1.9.9.294.1.4.0.2 |
This notification is generated whenever there is
a zone merge failure.
If all VSANs on a link have a zone-merge failure
at the same time, then just one notification is
generated in which zoneMergeFailureVSANNum object
has a zero value.
The zoneMergeFailureObject and
zoneMergeFailureReason assist in providing
information regarding the point of merge failure. |
Status: current |
Access: read-write |
NOTIFICATION-TYPE |
|
|
|
zoneMergeSuccessNotify |
1.3.6.1.4.1.9.9.294.1.4.0.3 |
This notification is generated whenever a zone
merge happens successfully.
If all VSANs on a link have a zone-merge success
at the same time, then just one notification is
generated in which zoneMergeSuccessVSANNum object
has a zero value. |
Status: current |
Access: read-write |
NOTIFICATION-TYPE |
|
|
|
zoneDefZoneBehaviourChngNotify |
1.3.6.1.4.1.9.9.294.1.4.0.4 |
This notification is generated whenever the
value of zoneDefaultZoneBehaviour changes. |
Status: current |
Access: read-write |
NOTIFICATION-TYPE |
|
|
|
zoneUnsuppMemInIntOpModeNotify |
1.3.6.1.4.1.9.9.294.1.4.0.5 |
This notification is generated whenever one or
more zone members are not supported in the
mode in which the local switch is currently
configured to function. The switch can be
configured to operate in certain 'interoperable'
modes on a VSAN basis to enable it to work with
switches from other vendors. The zoneVsanId object
identifies the VSAN on which the mismatch has
been identified. |
Status: current |
Access: read-write |
NOTIFICATION-TYPE |
|
|
|
zoneActivateNotify |
1.3.6.1.4.1.9.9.294.1.4.0.6 |
This notification is generated whenever a
zone set is activated/deactivated on a VSAN.
The zoneSetActivateResult object denotes
the outcome of the activation/deactivation.
The zoneSwitchWwn object represents the
WWN of the local device. |
Status: current |
Access: read-write |
NOTIFICATION-TYPE |
|
|
|
zoneCompactNotify |
1.3.6.1.4.1.9.9.294.1.4.0.7 |
This notification is generated whenever a
zone compaction on the VSAN specified by
zoneCompactVsan happens successfully. |
Status: current |
Access: read-write |
NOTIFICATION-TYPE |
|
|
|
zoneServerMIBCompliance |
1.3.6.1.4.1.9.9.294.2.1.1 |
The compliance statement for entities which
implement the Zone Server. |
Status: deprecated |
Access: read-write |
MODULE-COMPLIANCE |
|
|
|
zoneServerMIBCompliance1 |
1.3.6.1.4.1.9.9.294.2.1.2 |
The compliance statement for entities which
implement the Zone Server. |
Status: deprecated |
Access: read-write |
MODULE-COMPLIANCE |
|
|
|
zoneServerMIBComplianceRev2 |
1.3.6.1.4.1.9.9.294.2.1.3 |
The compliance statement for entities which
implement the Zone Server. |
Status: deprecated |
Access: read-write |
MODULE-COMPLIANCE |
|
|
|
zoneServerMIBComplianceRev3 |
1.3.6.1.4.1.9.9.294.2.1.4 |
The compliance statement for entities which
implement the Zone Server. |
Status: deprecated |
Access: read-write |
MODULE-COMPLIANCE |
|
|
|
zoneServerMIBComplianceRev4 |
1.3.6.1.4.1.9.9.294.2.1.5 |
The compliance statement for entities which
implement the Zone Server. |
Status: deprecated |
Access: read-write |
MODULE-COMPLIANCE |
|
|
|
zoneServerMIBComplianceRev5 |
1.3.6.1.4.1.9.9.294.2.1.6 |
The compliance statement for entities which
implement the Zone Server. |
Status: deprecated |
Access: read-write |
MODULE-COMPLIANCE |
|
|
|
zoneServerMIBComplianceRev6 |
1.3.6.1.4.1.9.9.294.2.1.7 |
The compliance statement for entities which
implement the Zone Server. |
Status: deprecated |
Access: read-write |
MODULE-COMPLIANCE |
|
|
|
zoneServerMIBComplianceRev7 |
1.3.6.1.4.1.9.9.294.2.1.8 |
The compliance statement for entities which
implement the Zone Server. |
Status: deprecated |
Access: read-write |
MODULE-COMPLIANCE |
|
|
|
zoneServerMIBComplianceRev8 |
1.3.6.1.4.1.9.9.294.2.1.9 |
The compliance statement for entities which
implement the Zone Server. |
Status: current |
Access: read-write |
MODULE-COMPLIANCE |
|
|
|
zoneConfigurationGroup |
1.3.6.1.4.1.9.9.294.2.2.1 |
A collection of objects for displaying and configuring
Zone Membership. |
Status: deprecated |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneStatisticsGroup |
1.3.6.1.4.1.9.9.294.2.2.2 |
A collection of objects for displaying the Zone
Server statistics information. |
Status: current |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneNotificationControlGroup |
1.3.6.1.4.1.9.9.294.2.2.3 |
A collection of notification control and
notification information objects for monitoring
Zone Server request rejection and zone merge
failures. |
Status: deprecated |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneNotificationGroup |
1.3.6.1.4.1.9.9.294.2.2.4 |
A collection of notification(s) for monitoring
Zone Server request rejection, zone merge
failures and successes and default zoning
behavioural changes. |
Status: deprecated |
Access: read-write |
NOTIFICATION-GROUP |
|
|
|
zoneConfigurationGroup1 |
1.3.6.1.4.1.9.9.294.2.2.5 |
A collection of objects for displaying and configuring
Zone Membership and deleting the local zone server
database. |
Status: deprecated |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneConfigurationGroup2 |
1.3.6.1.4.1.9.9.294.2.2.6 |
A collection of objects for displaying and configuring
Zone Membership and deleting the local zone server
database. |
Status: deprecated |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneLunStatsGroup |
1.3.6.1.4.1.9.9.294.2.2.7 |
A collection of objects for displaying the Zone
Server LUN statistics information. |
Status: current |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneConfigurationGroup3 |
1.3.6.1.4.1.9.9.294.2.2.8 |
A collection of objects for displaying and configuring
Zone Membership and deleting the local zone server
database. |
Status: deprecated |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneNotificationControlGroup1 |
1.3.6.1.4.1.9.9.294.2.2.9 |
A collection of notification control and
notification information objects for monitoring
Zone Server request rejection and zone merge
failures. |
Status: current |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneNotificationGroup1 |
1.3.6.1.4.1.9.9.294.2.2.10 |
A collection of notification(s) for monitoring
Zone Server request rejection, zone merge
failures and successes and default zoning
behavioural changes. |
Status: deprecated |
Access: read-write |
NOTIFICATION-GROUP |
|
|
|
zoneConfigurationGroup4 |
1.3.6.1.4.1.9.9.294.2.2.11 |
A collection of objects for displaying and configuring
Zone Membership and deleting the local zone server
database. |
Status: deprecated |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneConfigurationGroup5 |
1.3.6.1.4.1.9.9.294.2.2.12 |
A collection of objects for displaying and configuring
Zone Membership and deleting the local zone server
database. |
Status: deprecated |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneConfigurationGroup6 |
1.3.6.1.4.1.9.9.294.2.2.13 |
A collection of objects for displaying and configuring
Zone Membership and deleting the local zone server
database. |
Status: deprecated |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneNotificationGroup2 |
1.3.6.1.4.1.9.9.294.2.2.14 |
A collection of notification(s) for monitoring
Zone Server request rejection, zone merge
failures and successes and default zoning
behavioural changes. |
Status: current |
Access: read-write |
NOTIFICATION-GROUP |
|
|
|
zoneNotificationControlGroup1Sup1 |
1.3.6.1.4.1.9.9.294.2.2.15 |
A group that supplements
zoneNotificationControlGroup1 with additional
object(s). |
Status: current |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneConfigGroupSup1 |
1.3.6.1.4.1.9.9.294.2.2.16 |
A collection of objects to associate zones
to zonesets and facilitate compaction of
first 2k zones associated with zonesets. |
Status: current |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneNotificationControlGroup1Sup2 |
1.3.6.1.4.1.9.9.294.2.2.17 |
A group that supplements
zoneNotificationControlGroup1 with additional
notification information object(s). |
Status: current |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneNotificationGroup2Sup1 |
1.3.6.1.4.1.9.9.294.2.2.18 |
A group that supplements zoneNotificationGroup2
with additional notification(s). |
Status: current |
Access: read-write |
NOTIFICATION-GROUP |
|
|
|
zoneConfigGroupSup2 |
1.3.6.1.4.1.9.9.294.2.2.19 |
A collection of objects to copy active zonesets to
full zonesets on a VSAN. |
Status: current |
Access: read-write |
OBJECT-GROUP |
|
|
|
zoneConfigurationGroup7 |
1.3.6.1.4.1.9.9.294.2.2.20 |
A collection of objects for displaying and configuring
Zone Membership and deleting the local zone server
database. |
Status: current |
Access: read-write |
OBJECT-GROUP |
|
|
|