CISCO-WAN-SVC-MIB

File: CISCO-WAN-SVC-MIB.mib (189538 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
IF-MIB	PNNI-MIB	ATM-FORUM-TC-MIB
CISCO-WAN-ATM-CONN-MIB	CISCOWAN-SMI

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Counter32
Integer32	DisplayString	RowStatus
TimeStamp	TruthValue	TEXTUAL-CONVENTION
MODULE-COMPLIANCE	OBJECT-GROUP	ifIndex
InterfaceIndex	PnniNodeId	PnniPortId
AtmAddress	NetPrefix	CiscoWanNsapAtmAddress
stratacom

Defined Types

CwspSpvcState
Defines possible failures at an endpoint. The following are implemented: genSpvcErr(1) -- General SPVC error, sRecvSetupConfmMismatch(12) -- Connection ATM Conformance type -- mismatch with master at slave endpoint. sRecvSetupServMismatch(13) -- Connection Service type mismatch with -- master at slave endpoint. sRecvSetupTrafParmMismatch(14), -- Traffic parameters mismatch with master -- at slave endpoint. masterSpvcAutoDelete(15) -- Controller auto deleting provisioned -- master SPVC. and slaveSpvcAutoDelete(16) -- Controller auto deleting provisioned -- slave SPVC.
TEXTUAL-CONVENTION
	INTEGER	genSpvcErr(1), mPvcDelFail(2), sPvcDelFail(3), mRelPendHalfTmout(4), mInstlPvcFail(5), sInstlPvcFail(6), mRecmtPvcFail(7), sRecmtPvcFail(8), mCmtHalfFail(9), sCmtHalfFail(10), mInstlXconnFail(11), sRecvSetupConfmMismatch(12), sRecvSetupServMismatch(13), sRecvSetupTrafParmMismatch(14), masterSpvcAutoDelete(15), slaveSpvcAutoDelete(16)

CwspControllerState
Defines possible state for the pnni controller.
TEXTUAL-CONVENTION
	INTEGER	ready(1), unavilable(2)

CwspSscopEntry
SEQUENCE
	cwspSscopTmrCC	Integer32
	cwspSscopTmrKeepAlive	Integer32
	cwspSscopTmrNoResp	Integer32
	cwspSscopTmrPoll	Integer32
	cwspSscopTmtIdle	Integer32
	cwspSscopMaxCC	Integer32
	cwspSscopMaxPD	Integer32
	cwspSscopMaxSTAT	Integer32

CwspSscopStatsEntry
SEQUENCE
	cwspSscopCounterReset	INTEGER
	cwspSscopIgnoredPduRcv	Counter32
	cwspSscopBgnRcv	Counter32
	cwspSscopBgakRcv	Counter32
	cwspSscopEndRcv	Counter32
	cwspSscopEndakRcv	Counter32
	cwspSscopRsRcv	Counter32
	cwspSscopRsakRcv	Counter32
	cwspSscopBgrejRcv	Counter32
	cwspSscopSdRcv	Counter32
	cwspSscopSdpRcv	Counter32
	cwspSscopPollRcv	Counter32
	cwspSscopStatRcv	Counter32
	cwspSscopUstatRcv	Counter32
	cwspSscopUdRcv	Counter32
	cwspSscopMdRcv	Counter32
	cwspSscopErakRcv	Counter32
	cwspSscopBgnXmt	Counter32
	cwspSscopBgakXmt	Counter32
	cwspSscopEndXmt	Counter32
	cwspSscopEndakXmt	Counter32
	cwspSscopRsXmt	Counter32
	cwspSscopRsakXmt	Counter32
	cwspSscopBgrejXmt	Counter32
	cwspSscopSdXmt	Counter32
	cwspSscopSdpXmt	Counter32
	cwspSscopPollXmt	Counter32
	cwspSscopStatXmt	Counter32
	cwspSscopUstatXmt	Counter32
	cwspSscopUdXmt	Counter32
	cwspSscopMdXmt	Counter32
	cwspSscopErakXmt	Counter32

CwspSigConfigEntry
SEQUENCE
	cwspSigCfgT301	Integer32
	cwspSigCfgT303	Integer32
	cwspSigCfgT308	Integer32
	cwspSigCfgT310	Integer32
	cwspSigCfgT316	Integer32
	cwspSigCfgT317	Integer32
	cwspSigCfgT322	Integer32
	cwspSigCfgT397	Integer32
	cwspSigCfgT398	Integer32
	cwspSigCfgT399	Integer32

CwspSigStatsEntry
SEQUENCE
	cwspSigCounterReset	INTEGER
	cwspCallProcRcv	Counter32
	cwspConnectRcv	Counter32
	cwspConnectAckRcv	Counter32
	cwspSetupRcv	Counter32
	cwspReleaseRcv	Counter32
	cwspReleaseComplRcv	Counter32
	cwspRestartRcv	Counter32
	cwspRestartAckRcv	Counter32
	cwspStatusRcv	Counter32
	cwspStatusEnqRcv	Counter32
	cwspNotifyRcv	Counter32
	cwspAlertRcv	Counter32
	cwspProgressRcv	Counter32
	cwspAddPtyRcv	Counter32
	cwspAddPtyAckRcv	Counter32
	cwspAddPtyRejRcv	Counter32
	cwspDropPtyRcv	Counter32
	cwspIncorrectMsgRcv	Counter32
	cwspTimerExpiries	Counter32
	cwspLastCause	Counter32
	cwspLastDiagnostic	Integer32
	cwspCallProcXmt	Counter32
	cwspConnectXmt	Counter32
	cwspConnectAckXmt	Counter32
	cwspSetupXmt	Counter32
	cwspReleaseXmt	Counter32
	cwspReleaseComplXmt	Counter32
	cwspRestartXmt	Counter32
	cwspRestartAckXmt	Counter32
	cwspStatusXmt	Counter32
	cwspStatusEnqXmt	Counter32
	cwspNotifyXmt	Counter32
	cwspAlertXmt	Counter32
	cwspProgressXmt	Counter32
	cwspAddPtyXmt	Counter32
	cwspAddPtyAckXmt	Counter32
	cwspAddPtyRejXmt	Counter32
	cwspDropPtyXmt	Counter32
	cwspSscopStatus	INTEGER

CwspConfigEntry
SEQUENCE
	cwspAdminStatus	INTEGER
	cwspOperStatus	INTEGER
	cwspSvcBlocked	TruthValue
	cwspSpvcBlocked	TruthValue
	cwspIlmiAddrRegEnable	TruthValue
	cwspIlmiAutoConfEnable	TruthValue
	cwspIlmiServRegEnable	TruthValue
	cwspPhyIdentifier	DisplayString
	cwspSignallingVpi	Integer32
	cwspSignallingVci	Integer32
	cwspRoutingVpi	Integer32
	cwspRoutingVci	Integer32
	cwspMaxVpiBits	Integer32
	cwspMaxVciBits	Integer32
	cwspUniVersion	INTEGER
	cwspNniVersion	INTEGER
	cwspUniType	INTEGER
	cwspSide	INTEGER
	cwspMaxP2pCalls	Integer32
	cwspMaxP2mpRoots	Integer32
	cwspMaxP2mpLeafs	Integer32
	cwspMinSvccVpi	Integer32
	cwspMaxSvccVpi	Integer32
	cwspMinSvccVci	Integer32
	cwspMaxSvccVci	Integer32
	cwspMinSvpcVpi	Integer32
	cwspMaxSvpcVpi	Integer32
	cwspEnhancedIisp	TruthValue
	cwspConfigTableRowStatus	RowStatus
	cwspAddrPlanSupported	INTEGER
	cwspIlmiSecureLink	TruthValue
	cwspIlmiAttachmentPoint	TruthValue
	cwspIlmiLocalAttrStd	TruthValue
	cwspIlmiUCSMEnable	TruthValue
	cwspRoutingPriority	Integer32
	cwspSpvcAddress	CiscoWanNsapAtmAddress

CwspCallStatsEntry
SEQUENCE
	cwspCountReset	INTEGER
	cwspInCallAttempts	Counter32
	cwspInCallEstabs	Counter32
	cwspInCallFailures	Counter32
	cwspInFilterFailures	Counter32
	cwspInRouteFailures	Counter32
	cwspInResrcFailures	Counter32
	cwspInTimerFailures	Counter32
	cwspInCrankbacks	Counter32
	cwspOutCallAttempts	Counter32
	cwspOutCallEstabs	Counter32
	cwspOutCallFailures	Counter32
	cwspOutFilterFailures	Counter32
	cwspOutRouteFailures	Counter32
	cwspOutResrcFailures	Counter32
	cwspOutTimerFailures	Counter32
	cwspOutCrankbacks	Counter32

CwspPrefixEntry
SEQUENCE
	cwspNetPrefix	NetPrefix
	cwspPrefixRowStatus	RowStatus

CwspAddressEntry
SEQUENCE
	cwspAtmAddress	AtmAddress
	cwspAddrLen	INTEGER
	cwspAddrType	INTEGER
	cwspAddrProto	INTEGER
	cwspAddrPlan	INTEGER
	cwspAddrScope	INTEGER
	cwspAddrRedistribute	TruthValue
	cwspAddressRowStatus	RowStatus

CwspRegAddressEntry
SEQUENCE
	cwspRegAtmAddress	AtmAddress
	cwspRegAddressOrgSscope	INTEGER

CwspCacConfigEntry
SEQUENCE
	cwspUtilFactorCbr	Integer32
	cwspUtilFactorRtVbr	Integer32
	cwspUtilFactorNrtVbr	Integer32
	cwspUtilFactorAbr	Integer32
	cwspUtilFactorUbr	Integer32
	cwspMaxBwCbr	Integer32
	cwspMaxBwRtVbr	Integer32
	cwspMaxBwNrtVbr	Integer32
	cwspMaxBwAbr	Integer32
	cwspMaxBwUbr	Integer32
	cwspMinBwCbr	Integer32
	cwspMinBwRtVbr	Integer32
	cwspMinBwNrtVbr	Integer32
	cwspMinBwAbr	Integer32
	cwspMinBwUbr	Integer32
	cwspMaxVcCbr	Integer32
	cwspMaxVcRtVbr	Integer32
	cwspMaxVcNrtVbr	Integer32
	cwspMaxVcAbr	Integer32
	cwspMaxVcUbr	Integer32
	cwspMinVcCbr	Integer32
	cwspMinVcRtVbr	Integer32
	cwspMinVcNrtVbr	Integer32
	cwspMinVcAbr	Integer32
	cwspMinVcUbr	Integer32
	cwspMaxVcBwCbr	Integer32
	cwspMaxVcBwRtVbr	Integer32
	cwspMaxVcBwNrtVbr	Integer32
	cwspMaxVcBwAbr	Integer32
	cwspMaxVcBwUbr	Integer32
	cwspDefaultCdvtCbr	Integer32
	cwspDefaultCdvtRtVbr	Integer32
	cwspDefaultCdvtNrtVbr	Integer32
	cwspDefaultCdvtAbr	Integer32
	cwspDefaultCdvtUbr	Integer32
	cwspDefaultMbsRtVbr	Integer32
	cwspDefaultMbsNrtVbr	Integer32

CwspLoadEntry
SEQUENCE
	cwspLoadBwTotal	Integer32
	cwspLoadMaxBwCbr	Integer32
	cwspLoadMaxBwRtVbr	Integer32
	cwspLoadMaxBwNrtVbr	Integer32
	cwspLoadMaxBwAbr	Integer32
	cwspLoadMaxBwUbr	Integer32
	cwspLoadBwAvail	Integer32
	cwspLoadAvlBwCbr	Integer32
	cwspLoadAvlBwRtVbr	Integer32
	cwspLoadAvlBwNrtVbr	Integer32
	cwspLoadAvlBwAbr	Integer32
	cwspLoadAvlBwUbr	Integer32
	cwspLoadVcAvail	Integer32
	cwspLoadAvlVcCbr	Integer32
	cwspLoadAvlVcRtVbr	Integer32
	cwspLoadAvlVcNrtVbr	Integer32
	cwspLoadAvlVcAbr	Integer32
	cwspLoadAvlVcUbr	Integer32
	cwspLoadCtdCbr	Integer32
	cwspLoadCtdRtVbr	Integer32
	cwspLoadCtdNrtVbr	Integer32
	cwspLoadCtdAbr	Integer32
	cwspLoadCtdUbr	Integer32
	cwspLoadCdvCbr	Integer32
	cwspLoadCdvRtVbr	Integer32
	cwspLoadCdvNrtVbr	Integer32
	cwspLoadCdvAbr	Integer32
	cwspLoadCdvUbr	Integer32
	cwspLoadClr0Cbr	Integer32
	cwspLoadClr0RtVbr	Integer32
	cwspLoadClr0NrtVbr	Integer32
	cwspLoadClr0Abr	Integer32
	cwspLoadClr0Ubr	Integer32
	cwspLoadClr01Cbr	Integer32
	cwspLoadClr01RtVbr	Integer32
	cwspLoadClr01NrtVbr	Integer32
	cwspLoadClr01Abr	Integer32
	cwspLoadClr01Ubr	Integer32
	cwspLoadMinGurCrCbr	Integer32
	cwspLoadMinGurCrRtVbr	Integer32
	cwspLoadMinGurCrNrtVbr	Integer32
	cwspLoadMinGurCrAbr	Integer32
	cwspLoadMinGurCrUbr	Integer32

CwspCallEntry
SEQUENCE
	cwspCallVpi	Integer32
	cwspCallVci	Integer32
	cwspCallLeafReference	Integer32
	cwspCallCallRef	Integer32
	cwspCallCallingAddress	AtmAddress
	cwspCallCalledAddress	AtmAddress
	cwspCallCallingSubAddr	AtmAddress
	cwspCallCalledSubAddr	AtmAddress
	cwspCallOtherIntfIndex	Integer32
	cwspCallOtherIntfVpi	Integer32
	cwspCallOtherIntfVci	Integer32
	cwspCallOtherIntfCallRef	Integer32
	cwspCallType	INTEGER
	cwspCallStartTime	TimeStamp
	cwspCallBearerClass	INTEGER
	cwspCallServiceCategory	INTEGER
	cwspCallCastType	INTEGER
	cwspCallClipSusceptibility	INTEGER
	cwspCallFwdConformance	INTEGER
	cwspCallFwdPcr	Integer32
	cwspCallFwdScr	Integer32
	cwspCallFwdMbs	Integer32
	cwspCallFwdCdvt	Integer32
	cwspCallFwdFrameDiscard	INTEGER
	cwspCallBwdConformance	INTEGER
	cwspCallBwdPcr	Integer32
	cwspCallBwdScr	Integer32
	cwspCallBwdMbs	Integer32
	cwspCallBwdCdvt	Integer32
	cwspCallBwdFrameDiscard	INTEGER
	cwspCallMaxCtd	Integer32
	cwspCallMaxFwdCdv	Integer32
	cwspCallMaxFwdClr	Integer32
	cwspCallMaxBwdCdv	Integer32
	cwspCallMaxBwdClr	Integer32

CwspAbrCallEntry
SEQUENCE
	cwspAbrCallVpi	Integer32
	cwspAbrCallVci	Integer32
	cwspAbrCallCallRef	Integer32
	cwspAbrCallClgAddress	AtmAddress
	cwspAbrCallCldAddress	AtmAddress
	cwspAbrCallClgSubAddr	AtmAddress
	cwspAbrCallCldSubAddr	AtmAddress
	cwspAbrCallOtherIntfIndex	Integer32
	cwspAbrCallOtherIntfVpi	Integer32
	cwspAbrCallOtherIntfVci	Integer32
	cwspAbrCallOtherIntfCallRef	Integer32
	cwspAbrCallType	INTEGER
	cwspAbrCallStartTime	TimeStamp
	cwspAbrCallBearerClass	INTEGER
	cwspAbrCallServiceCategory	INTEGER
	cwspAbrCallCastType	INTEGER
	cwspAbrCallClipSusceptibility	INTEGER
	cwspAbrCallFwdConformance	INTEGER
	cwspAbrCallFwdPcr	Integer32
	cwspAbrCallFwdMcr	Integer32
	cwspAbrCallFwdIcr	Integer32
	cwspAbrCallFwdRif	INTEGER
	cwspAbrCallFwdRdf	INTEGER
	cwspAbrCallFwdTbe	Integer32
	cwspAbrCallFwdNrm	INTEGER
	cwspAbrCallFwdTrm	INTEGER
	cwspAbrCallFwdAdtf	Integer32
	cwspAbrCallFwdCdf	INTEGER
	cwspAbrCallFwdFrameDiscard	INTEGER
	cwspAbrCallBwdPcr	Integer32
	cwspAbrCallBwdMcr	Integer32
	cwspAbrCallBwdIcr	Integer32
	cwspAbrCallBwdRif	INTEGER
	cwspAbrCallBwdRdf	INTEGER
	cwspAbrCallBwdTbe	Integer32
	cwspAbrCallBwdNrm	INTEGER
	cwspAbrCallBwdTrm	INTEGER
	cwspAbrCallBwdAdtf	Integer32
	cwspAbrCallBwdCdf	INTEGER
	cwspAbrCallBwdFrameDiscard	INTEGER
	cwspAbrCallFrtt	Integer32
	cwspAbrCallMaxCtd	Integer32
	cwspAbrCallMaxFwdCdv	Integer32
	cwspAbrCallMaxFwdClr	Integer32
	cwspAbrCallMaxBwdCdv	Integer32
	cwspAbrCallMaxBwdClr	Integer32

CwspConnTraceCntlEntry
SEQUENCE
	cwspConnTraceIndex	Integer32
	cwspConnTraceifIndex	InterfaceIndex
	cwspConnTraceSrcVpi	Integer32
	cwspConnTraceSrcVci	Integer32
	cwspConnTraceType	INTEGER
	cwspConnTraceCallRef	Integer32
	cwspConnTraceLeafRef	Integer32
	cwspConnTraceDestVpi	Integer32
	cwspConnTraceDestVci	Integer32
	cwspConnTraceDestCallRef	Integer32
	cwspConnTraceResultStatus	INTEGER
	cwspConnTraceQueryStatus	RowStatus

CwspConnTraceEntry
SEQUENCE
	cwspConnTraceDataIndex	Integer32
	cwspConnTraceNodeId	PnniNodeId
	cwspConnTraceEgressPortId	PnniPortId
	cwspConnTraceEgressVpi	Integer32
	cwspConnTraceEgressVci	Integer32
	cwspConnTraceEgressCallRef	Integer32
	cwspConnTraceEgressPhyPortId	OCTET STRING
	cwspConnTraceLastNode	TruthValue

CwspOperationEntry
SEQUENCE
	cwspOperIlmiEnable	TruthValue
	cwspOperIfcType	INTEGER
	cwspOperIfcSide	INTEGER
	cwspOperMaxVPCs	Integer32
	cwspOperMaxVCCs	Integer32
	cwspOperMaxVpiBits	Integer32
	cwspOperMaxVciBits	Integer32
	cwspOperUniType	INTEGER
	cwspOperUniVersion	INTEGER
	cwspOperDeviceType	INTEGER
	cwspOperIlmiVersion	INTEGER
	cwspOperNniSigVersion	INTEGER
	cwspOperMaxSvpcVpi	Integer32
	cwspOperMinSvpcVpi	Integer32
	cwspOperMaxSvccVpi	Integer32
	cwspOperMinSvccVpi	Integer32
	cwspOperMaxSvccVci	Integer32
	cwspOperMinSvccVci	Integer32
	cwspOperAddrPlanSupported	INTEGER

Defined Values

ciscoWANSvcMIB		2.1.351.140
The MIB modules describe an ATM network service on a BPX-SES or a MGX ATM switch. This MIB module provides configuring, provisioning, as well as status gathering for ATM services. Abbreviation used: ABR -- Available Bit Rate AINI -- ATM Inter-Network Interface ATM -- Asynchronous Transfer Mode BGN -- Begin BW -- Bandwidth CBR -- Constant Bit Rate ENNI -- Enhanced Network to Network Interface Note: The 'ENNI' term used here indicating 'enhanced' or 'friendly' NNI for linking two networks of CISCO AutoRoute or PNNI switches. The XPVCs and XPVPs are provisioned across them. Functionality includes changing segment OAM cell handling so that these cells flow over 'end-to-end OAM segment' loops for the provisioned length of the XPVC or XPVP, i.e. the 'segment' comprises the two or three segments between the user ports. Also implemented at ENNIs is an LMI functionality that enables auto-discovery of the ENNIs. ER -- Error Recovery GAT -- Generic Application Transport IE -- Information Element IISP -- Interim Inter-Switch Signaling Protocol ILMI -- Interim Local Management Interface MD -- Management Data PNNI -- Private Network-Network Interface RS -- Resynchronization REJ -- Rejection SD -- Sequence Data SDP -- Sequence Data with Poll SPVC -- Soft Permanent Virtual Circuit SSCOP -- Service Specific Connection Oriented Protocol SVC -- Switched Virtual Circuit UBR -- Unspecified Bit Rate UD -- Unit Data UNI -- User-Network Interface USTAT -- Unsolicited STAT VBR -- Variable Bit Rate
MODULE-IDENTITY

ciscoWANSvcMIBObjects		2.1.351.140.1
OBJECT IDENTIFIER

ciscoWANSvcInfo		2.1.351.140.1.1
OBJECT IDENTIFIER

ciscoWANSvcPort		2.1.351.140.1.2
OBJECT IDENTIFIER

ciscoWANPnniRouting		2.1.351.140.1.3
OBJECT IDENTIFIER

ciscoWANSpvc		2.1.351.140.1.4
OBJECT IDENTIFIER

cwspConfig		2.1.351.140.1.2.1
OBJECT IDENTIFIER

cwspCacConfig		2.1.351.140.1.2.2
OBJECT IDENTIFIER

cwspSigConfig		2.1.351.140.1.2.3
OBJECT IDENTIFIER

cwspSscopConfig		2.1.351.140.1.2.4
OBJECT IDENTIFIER

cwspCallStats		2.1.351.140.1.2.5
OBJECT IDENTIFIER

cwspSigStats		2.1.351.140.1.2.6
OBJECT IDENTIFIER

cwspSscopStats		2.1.351.140.1.2.7
OBJECT IDENTIFIER

cwspCall		2.1.351.140.1.2.8
OBJECT IDENTIFIER

cwspAbrCall		2.1.351.140.1.2.9
OBJECT IDENTIFIER

cwspPrefix		2.1.351.140.1.2.10
OBJECT IDENTIFIER

cwspAddress		2.1.351.140.1.2.11
OBJECT IDENTIFIER

cwspRegAddress		2.1.351.140.1.2.12
OBJECT IDENTIFIER

cwspLoad		2.1.351.140.1.2.13
OBJECT IDENTIFIER

cwspConnTrace		2.1.351.140.1.2.14
OBJECT IDENTIFIER

cwspOperation		2.1.351.140.1.2.15
OBJECT IDENTIFIER

cwsSwRevision		2.1.351.140.1.1.1
PNNI network controller software revision number.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

cwsControllerStatus		2.1.351.140.1.1.6
The administrative status for the pnni active controller.
Status: current	Access: read-only
OBJECT-TYPE
	CwspControllerState

cwspPnniStndbyControllerStatus		2.1.351.140.1.1.7
The administrative status for the standby controller.
Status: current	Access: read-only
OBJECT-TYPE
	CwspControllerState

cwspPnniControllerStatus		2.1.351.140.1.1.8
The administrative status of the pnni controller. Note: this object is only used in the trap varbind, snmp get operation is meaningless.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), stndby(2), unavailable(3)

cwspPnniControllerPhySlot		2.1.351.140.1.1.9
The pnni controller physical location for MGX or BPX-SES. Note: this object is only used in the trap varbind, snmp get operation is meaningless.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..16

cwspSscopTable		2.1.351.140.1.2.4.1
This table specifies SSCOP (Layer 2) configuration parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspSscopEntry

cwspSscopEntry		2.1.351.140.1.2.4.1.1
An entry in the SSCOP configuration table. Each entry indexed by the ifIndex of a port.
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspSscopEntry

cwspSscopTmrCC		2.1.351.140.1.2.4.1.1.1
This object contains the value for Connection control timer.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspSscopTmrKeepAlive		2.1.351.140.1.2.4.1.1.2
This object contains the value for keep alive timer
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspSscopTmrNoResp		2.1.351.140.1.2.4.1.1.3
This object contains the value for no response timer.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspSscopTmrPoll		2.1.351.140.1.2.4.1.1.4
This object contains the value for poll timer.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspSscopTmtIdle		2.1.351.140.1.2.4.1.1.5
This object contains the value for idle timer.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspSscopMaxCC		2.1.351.140.1.2.4.1.1.6
This object contains the upper limit for the number of transmissions of a BGN, END, ER or RS PDU.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspSscopMaxPD		2.1.351.140.1.2.4.1.1.7
This object contains an upper limit for a counter which counts the number of SD PDUs transmitted between transmissions of POLL PDUs or the number of SD PDUs transmitted before the transmission of the first POLL PDU after POLL timer became active.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspSscopMaxSTAT		2.1.351.140.1.2.4.1.1.8
This object contains an upper limit for the number of list elements placed in a STAT PDU.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspSscopStatsTable		2.1.351.140.1.2.7.1
This table contains SSCOP (Layer 2) statistics counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspSscopStatsEntry

cwspSscopStatsEntry		2.1.351.140.1.2.7.1.1
An entry contains SSCOP (Layer 2) statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspSscopStatsEntry

cwspSscopCounterReset		2.1.351.140.1.2.7.1.1.1
This object specifies whether the SSCOP statistics collected for this interface needs to be reset.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noop(1), reset(2)

cwspSscopIgnoredPduRcv		2.1.351.140.1.2.7.1.1.2
This object stores the number of SSCOP PDUs that are received but ignored due to incorrect size, invalid PDU, unknown PDU type.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopBgnRcv		2.1.351.140.1.2.7.1.1.3
This object stores the number of SSCOP BGN PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopBgakRcv		2.1.351.140.1.2.7.1.1.4
This object stores the number of SSCOP BGN ACK PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopEndRcv		2.1.351.140.1.2.7.1.1.5
This object stores the number of SSCOP END PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopEndakRcv		2.1.351.140.1.2.7.1.1.6
This object stores the number of SSCOP END ACK PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopRsRcv		2.1.351.140.1.2.7.1.1.7
This object stores the number of SSCOP RS(Resync) PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopRsakRcv		2.1.351.140.1.2.7.1.1.8
This object stores the number of SSCOP RS(Resync) ACK PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopBgrejRcv		2.1.351.140.1.2.7.1.1.9
This object stores the number of SSCOP BGN REJ PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopSdRcv		2.1.351.140.1.2.7.1.1.10
This object stores the number of SSCOP SD (Sequenced Data) PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopSdpRcv		2.1.351.140.1.2.7.1.1.11
This object stores the number of SSCOP SDP (Sequenced Data with Poll) PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopPollRcv		2.1.351.140.1.2.7.1.1.12
This object stores the number of SSCOP POLL PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopStatRcv		2.1.351.140.1.2.7.1.1.13
This object stores the number of SSCOP STAT PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopUstatRcv		2.1.351.140.1.2.7.1.1.14
This object stores the number of SSCOP USTAT (Unsolicited STAT) PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopUdRcv		2.1.351.140.1.2.7.1.1.15
This object stores the number of SSCOP UD (Unit data) PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopMdRcv		2.1.351.140.1.2.7.1.1.16
This object stores the number of SSCOP MD (Management data) PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopErakRcv		2.1.351.140.1.2.7.1.1.17
This object stores the number of SSCOP ER ACK (error recovery ack) PDUs received at this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopBgnXmt		2.1.351.140.1.2.7.1.1.18
This object stores the number of SSCOP BGN PDUs transmitted over this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopBgakXmt		2.1.351.140.1.2.7.1.1.19
This object stores the number of SSCOP BGN ACK PDUs transmitted on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopEndXmt		2.1.351.140.1.2.7.1.1.20
This object stores the number of SSCOP END PDUs transmitted on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopEndakXmt		2.1.351.140.1.2.7.1.1.21
This object stores the number of SSCOP END ACK PDUs transmitted on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopRsXmt		2.1.351.140.1.2.7.1.1.22
This object stores the number of SSCOP RS (Resync) PDUs transmitted over this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopRsakXmt		2.1.351.140.1.2.7.1.1.23
This object stores the number of SSCOP RS (Resync) ACK PDUs transmitted over this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopBgrejXmt		2.1.351.140.1.2.7.1.1.24
This object stores the number of SSCOP BGN REJ PDUs transmitted over this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopSdXmt		2.1.351.140.1.2.7.1.1.25
This object stores the number of SSCOP SD transmitted over this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopSdpXmt		2.1.351.140.1.2.7.1.1.26
This object stores the number of SSCOP SDP PDUs transmitted over this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopPollXmt		2.1.351.140.1.2.7.1.1.27
This object stores the number of SSCOP POLL PDUs transmitted over this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopStatXmt		2.1.351.140.1.2.7.1.1.28
This object stores the number of SSCOP STAT PDUs transmitted over this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopUstatXmt		2.1.351.140.1.2.7.1.1.29
This object stores the number of SSCOP USTAT PDUs transmitted over this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopUdXmt		2.1.351.140.1.2.7.1.1.30
This object stores the number of SSCOP UD PDUs transmitted over this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopMdXmt		2.1.351.140.1.2.7.1.1.31
This object stores the number of SSCOP MD PDUs transmitted over this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopErakXmt		2.1.351.140.1.2.7.1.1.32
This object stores the number of SSCOP ER(error recovery) ACK PDUs transmitted over this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSigConfigTable		2.1.351.140.1.2.3.1
This table specifies signaling configuration parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspSigConfigEntry

cwspSigConfigEntry		2.1.351.140.1.2.3.1.1
An entry in the signaling configuration table. Each entry indexed by the ifIndex of a port.
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspSigConfigEntry

cwspSigCfgT301		2.1.351.140.1.2.3.1.1.1
Timer started when ALERT message received at Call Received State. Normally, timer is stopped when CONNECT message is received. Clear call at first expiry.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	150..240

cwspSigCfgT303		2.1.351.140.1.2.3.1.1.2
Timer started when SETUP message sent at Call Present State. Normally, timer is stopped when ALERT, CONNECT, RELEASE COMPLETE or CALL PROCEEDING message is received. Resend SETUP message and restart the timer at first expiry; Clear network connection and enter NULL state at second expiry.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	4..8

cwspSigCfgT308		2.1.351.140.1.2.3.1.1.3
Timer started when RELEASE message sent at Release Indication State. Normally, timer is stopped when RELEASE COMPLETE or RELEASE message is received. Resend RELEASE and restart the timer at first expiry; Release call reference and enter NULL state at second expiry.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	20..45

cwspSigCfgT310		2.1.351.140.1.2.3.1.1.4
Timer started when CALL PROCEEDING message received at Incoming Call Proceeding State. Normally, timer is stopped when ALERT, CONNECT or RELEASE message is received. Clear call at first expiry. Range from 10 to 20 seconds for UNI 3.0/3.1 with default of 10; 30 to 120 seconds for UNI 4.0 with default of 30, default number can be 10 or 30, 10 is used.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	10..120

cwspSigCfgT316		2.1.351.140.1.2.3.1.1.5
Timer started when RESTART message sent Restart Request State. Normally, timer is stopped when RESTART ACK message is received. RESTART may be sent multiple times in both first or second expiry.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	90..300

cwspSigCfgT317		2.1.351.140.1.2.3.1.1.6
Timer started when RESTART message received at Restart State. Normally, timer is stopped when Internal clearing of call references happen. Maintenance notification at first expiry. The value of this timer should be less than T316.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	60..300

cwspSigCfgT322		2.1.351.140.1.2.3.1.1.7
Timer started when STATUS ENQUIRY message sent at any call state. Normally, timer is stopped when STATUS RELEASE or RELEASE COMPLETE message is received. STATUS ENQUIREY message may be resent several times in both first or second expiry.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	4..20

cwspSigCfgT397		2.1.351.140.1.2.3.1.1.8
Timer started when ALERTING or PARTY ALERTING message received in point-to-multipoint call. Normally timer is stopped when ADD PARTY ACK message is received. Clear party at first expiry.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	180..240

cwspSigCfgT398		2.1.351.140.1.2.3.1.1.9
Timer is started when DROP PARTY message sent at Drop Party Initiated State. Normally, timer is stopped when DROP PARTY ACK or RELEASE message is received. Send DROP PARTY ACK or RELEASE at first expiry.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	4..20

cwspSigCfgT399		2.1.351.140.1.2.3.1.1.10
Timer is started when ADD PARTY message sent at Add Party Initiated State. Normally, timer is stopped when ADD PARTY ACK, ADD PARTY REJ or RELEASE message is received. Clear the party and enter NULL Party State at first expiry. Range from 14 to 28 seconds for UNI 3.0/3.1 with default of 14; 34 to 124 seconds for UNI 4.0 with default of 34, default can be 14 or 34, 14 is used.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	14..124

cwspSigStatsTable		2.1.351.140.1.2.6.1
This table contains signaling statistics counters
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspSigStatsEntry

cwspSigStatsEntry		2.1.351.140.1.2.6.1.1
An entry contains signaling statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspSigStatsEntry

cwspSigCounterReset		2.1.351.140.1.2.6.1.1.1
Writing a 2 to this object resets the all Sig counters.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noop(1), reset(2)

cwspCallProcRcv		2.1.351.140.1.2.6.1.1.2
Number of CALL PROCEEDING messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspConnectRcv		2.1.351.140.1.2.6.1.1.3
Number of CONNECT messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspConnectAckRcv		2.1.351.140.1.2.6.1.1.4
Number of CONNECT ACK messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSetupRcv		2.1.351.140.1.2.6.1.1.5
Number of SETUP messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspReleaseRcv		2.1.351.140.1.2.6.1.1.6
Number of RELEASE messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspReleaseComplRcv		2.1.351.140.1.2.6.1.1.7
Number of RELEASE COMPLETE messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspRestartRcv		2.1.351.140.1.2.6.1.1.8
Number of RESTART messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspRestartAckRcv		2.1.351.140.1.2.6.1.1.9
Number of RESTART ACK messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspStatusRcv		2.1.351.140.1.2.6.1.1.10
Number of STATUS messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspStatusEnqRcv		2.1.351.140.1.2.6.1.1.11
Number of STATUS ENQUIRY messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspNotifyRcv		2.1.351.140.1.2.6.1.1.12
Number of NOTIFY messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspAlertRcv		2.1.351.140.1.2.6.1.1.13
Number of ALERT messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspProgressRcv		2.1.351.140.1.2.6.1.1.14
Number of PROGRESS messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspAddPtyRcv		2.1.351.140.1.2.6.1.1.15
Number of ADD PARTY messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspAddPtyAckRcv		2.1.351.140.1.2.6.1.1.16
Number of ADD PARTY ACK messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspAddPtyRejRcv		2.1.351.140.1.2.6.1.1.17
Number of ADD PARTY REJECT messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspDropPtyRcv		2.1.351.140.1.2.6.1.1.18
Number of DROP PARTY messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspIncorrectMsgRcv		2.1.351.140.1.2.6.1.1.20
Number of Incorrect messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspTimerExpiries		2.1.351.140.1.2.6.1.1.21
Number of timeouts occurred on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspLastCause		2.1.351.140.1.2.6.1.1.22
to indicate the last cause of release or cranckback.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspLastDiagnostic		2.1.351.140.1.2.6.1.1.23
to indicate the last diagnostic of release or cranckback.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-2147483648..214743647

cwspCallProcXmt		2.1.351.140.1.2.6.1.1.24
Number of CALL PROCEEDING messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspConnectXmt		2.1.351.140.1.2.6.1.1.25
Number of CONNECT messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspConnectAckXmt		2.1.351.140.1.2.6.1.1.26
Number of CONNECT ACK messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSetupXmt		2.1.351.140.1.2.6.1.1.27
Number of SETUP messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspReleaseXmt		2.1.351.140.1.2.6.1.1.28
Number of RELEASE messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspReleaseComplXmt		2.1.351.140.1.2.6.1.1.29
Number of RELEASE COMPLETE messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspRestartXmt		2.1.351.140.1.2.6.1.1.30
Number of RESTART messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspRestartAckXmt		2.1.351.140.1.2.6.1.1.31
Number of RESTART ACK messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspStatusXmt		2.1.351.140.1.2.6.1.1.32
Number of STATUS messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspStatusEnqXmt		2.1.351.140.1.2.6.1.1.33
Number of STATUS ENQUIRY messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspNotifyXmt		2.1.351.140.1.2.6.1.1.34
Number of NOTIFY messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspAlertXmt		2.1.351.140.1.2.6.1.1.35
Number of ALERT messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspProgressXmt		2.1.351.140.1.2.6.1.1.36
Number of PROGRESS messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspAddPtyXmt		2.1.351.140.1.2.6.1.1.37
Number of ADD PARTY messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspAddPtyAckXmt		2.1.351.140.1.2.6.1.1.38
Number of ADD PARTY ACK messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspAddPtyRejXmt		2.1.351.140.1.2.6.1.1.39
Number of ADD PARTY REJECT messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspDropPtyXmt		2.1.351.140.1.2.6.1.1.40
Number of DROP PARTY messages transmitted from this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspSscopStatus		2.1.351.140.1.2.6.1.1.42
Sscop link status on an NNI interface, object is meaningful along with ciscoWANSscopLinkChange trap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

cwspConfigTable		2.1.351.140.1.2.1.1
The Interface configuration table collects attributes that affect the operation of the controller interface. There is a single row for each interface that the managed system is expected to be added or managed.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspConfigEntry

cwspConfigEntry		2.1.351.140.1.2.1.1.1
An entry in the interface configuration table containing information about an interface
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspConfigEntry

cwspAdminStatus		2.1.351.140.1.2.1.1.1.1
The administrative status of the interface. inService (1) means that the interface is operational while outService (2) indicates that the interface is put out of service by the administrator.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	inService(1), outService(2)

cwspOperStatus		2.1.351.140.1.2.1.1.1.2
The operational state of the interface. This status is derived from the physical state of the interface. failed (2) indicates that the interface has failed. ok (1) indicates that the interface is in operational status, while other (3) denotes that the interface is in an unknown state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), failed(2), other(3)

cwspSvcBlocked		2.1.351.140.1.2.1.1.1.3
Indicates whether Switches virtual connections are allowed through this interface.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cwspSpvcBlocked		2.1.351.140.1.2.1.1.1.4
Indicates whether soft permanent virtual connections are allowed through this interface.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cwspIlmiAddrRegEnable		2.1.351.140.1.2.1.1.1.5
Indicates whether ILMI address registration is enabled or disabled.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cwspIlmiAutoConfEnable		2.1.351.140.1.2.1.1.1.6
Indicates whether auto-configuration of the interface is turned on or off. If auto-configuration is enabled, then the interface comes up using the ILMI auto-configuration.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cwspIlmiServRegEnable		2.1.351.140.1.2.1.1.1.7
Indicates whether service registry is enabled or disabled on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cwspPhyIdentifier		2.1.351.140.1.2.1.1.1.8
Indicates the physical identification of the interface. Mandatory when the port is provisioned for the first time through SNMP.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString

cwspSignallingVpi		2.1.351.140.1.2.1.1.1.9
Denotes the Signaling VPI used on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..4095

cwspSignallingVci		2.1.351.140.1.2.1.1.1.10
Indicates the signaling VCI used on the interface, acceptable value is 32-65535, and 5 being the default.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

cwspRoutingVpi		2.1.351.140.1.2.1.1.1.11
Indicates the VPI used for PNNI lowest level RCC.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..4095

cwspRoutingVci		2.1.351.140.1.2.1.1.1.12
Indicates the VCI used for the PNNI lowest level RCC, acceptable value is 32-65535, and 18 being the default.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

cwspMaxVpiBits		2.1.351.140.1.2.1.1.1.13
The maximum number of active VPI bits on this ATM Interface. For virtual interfaces (i.e. Virtual Path Connections used by PNNI), this value has no meaning and is set to zero.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..12

cwspMaxVciBits		2.1.351.140.1.2.1.1.1.14
The maximum number of active VCI bits on this ATM Interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..16

cwspUniVersion		2.1.351.140.1.2.1.1.1.15
An indication of the latest version of the ATM Forum UNI Signaling Specification that is supported on this ATM Interface. If this value is not present, a version of the UNI earlier than 3.1 is supported. The value of 'self(9)' indicates this entry is a voice port. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	uni20(1), uni30(2), uni31(3), uni40(4), ituDss2(5), frf4(6), unsupported(7), ip(8), self(9)

cwspNniVersion		2.1.351.140.1.2.1.1.1.16
An indication of the latest version of the ATM Forum PNNI Signaling Specification that is supported on this ATM Interface. Note that the PNNI routing version is not determined through ILMI. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	iisp30(1), iisp31(2), pnni10(3), enni(4), aini(5), unsupported(7)

cwspUniType		2.1.351.140.1.2.1.1.1.17
The type of the ATM device, either public or private.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	public(1), private(2)

cwspSide		2.1.351.140.1.2.1.1.1.18
This object determines the type of the ATM device. This object is used in automatic ATM Interface-Type determination procedure such that a correct operational ATM Interface-type can be determined. An ATM End System shall take the value of user(1), and an ATM network node shall take the value of node(2).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	user(1), network(2)

cwspMaxP2pCalls		2.1.351.140.1.2.1.1.1.19
Indicates the maximum number of point to point calls (including VCs and VPs allowed on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

cwspMaxP2mpRoots		2.1.351.140.1.2.1.1.1.20
Indicates the maximum number of root VCs (for point-to-multipoint) allowed on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

cwspMaxP2mpLeafs		2.1.351.140.1.2.1.1.1.21
Indicates the maximum number of leaf VCs (for point-to-multipoint) allowed on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

cwspMinSvccVpi		2.1.351.140.1.2.1.1.1.22
Indicates the minimum SVCC VPI configured on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..4095

cwspMaxSvccVpi		2.1.351.140.1.2.1.1.1.23
Indicates the maximum SVCC VPI configured on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..4095

cwspMinSvccVci		2.1.351.140.1.2.1.1.1.24
Indicates the minimum SVCC VCI configured on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

cwspMaxSvccVci		2.1.351.140.1.2.1.1.1.25
Indicates the maximum SVCC VCI configured on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	35..65535

cwspMinSvpcVpi		2.1.351.140.1.2.1.1.1.26
Indicates the minimum SVPC VPI configured on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..4095

cwspMaxSvpcVpi		2.1.351.140.1.2.1.1.1.27
Indicates the maximum SVPC VPI configured on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..4095

cwspEnhancedIisp		2.1.351.140.1.2.1.1.1.28
Indicates whether the enhanced features for IISP are enabled or disabled.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cwspConfigTableRowStatus		2.1.351.140.1.2.1.1.1.29
Used to create and delete the Interface. However, only createAndGo, destroy, active and notInService are supported. NMS should only use createAndGo to create a row and destroy to delete a row. The managed device will either return active or notInService for a row status.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

cwspAddrPlanSupported		2.1.351.140.1.2.1.1.1.30
The ATM address plan supported on an interface. This can only be modified if interface is public UNI. For all other interfaces, the value is aesa.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	both(1), aesa(2), e164(3)

cwspIlmiSecureLink		2.1.351.140.1.2.1.1.1.31
Indicates whether ILMI Secure Link Protocol is enabled or disabled. When secure link protocol is enabled, loss in ILMI connectivity is treated as loss of attachment point which results in all SVCs/SVPs being released on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cwspIlmiAttachmentPoint		2.1.351.140.1.2.1.1.1.32
Indicates whether detection of loss of attachment procedures are enabled on this interface. When set to true, then standard ILMI procedures are employed to detect loss of attachment point. If set to false, then ILMI protocol on the interface does not detect the loss of attachment.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cwspIlmiLocalAttrStd		2.1.351.140.1.2.1.1.1.33
Indicates whether on modification of local attributes, procedures as recommended by ILMI 4.0 specification are followed or cisco proprietery procedures are followed. When set to true, the standard ILMI procedures are followed.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cwspIlmiUCSMEnable		2.1.351.140.1.2.1.1.1.34
Indicates whether ILMI user connection status monitoring is enabled or disabled.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cwspRoutingPriority		2.1.351.140.1.2.1.1.1.35
This object is the routing priority to be assigned to connections which enter the network from this ingress interface, but does not carry the routing priority signaling in the SETUP message. SETUP message. A default routing priority of 8 is used if this object is not configured. A routing priority 1 is the highest priority for a user connection. A connection tagged with a routing priority of 1 is derouted ahead of connections tagged with other priority values.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..15

cwspSpvcAddress		2.1.351.140.1.2.1.1.1.36
This object identifies the internal NSAP assigned to a port by the switch. a) The format is that of 13-byte node prefix and 7-byte port number. b) When the switch's node prefix is modified, the node prefix part of this variable is also changed accordingly. Note: the switch's node prefix cannot be changed if there are connections on the switch. c) The port number can be physical port identifier or the ifIndex of this port.
Status: current	Access: read-only
OBJECT-TYPE
	CiscoWanNsapAtmAddress

cwspCallStatsTable		2.1.351.140.1.2.5.1
This Table contains objects showing the Statistics for SVC/SPVC calls on a given interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspCallStatsEntry

cwspCallStatsEntry		2.1.351.140.1.2.5.1.1
An entry contains SVC/SPVC call statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspCallStatsEntry

cwspCountReset		2.1.351.140.1.2.5.1.1.1
Writing a 2 to this object resets all counters.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noop(1), reset(2)

cwspInCallAttempts		2.1.351.140.1.2.5.1.1.2
This object shows the number of incoming Signaling messages (Setup and Add Party) received by the switching node on this interface for Call establishment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspInCallEstabs		2.1.351.140.1.2.5.1.1.3
This object shows the number of incoming Signaling Messages (Connect and Add Party Ack) received by the switching node on this interface which marks that a call has been successfully established.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspInCallFailures		2.1.351.140.1.2.5.1.1.4
This object shows the total number of incoming Point-to-Point (p2p) and Point-to-MultiPoint(p2mp) SVC/SPVC call attempts failed on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspInFilterFailures		2.1.351.140.1.2.5.1.1.5
This object shows the number of incoming Point-to-Point(p2p) and Point-to-MultiPoint(p2mp) SVC/SPVC call attempts which failed due to address filtering on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspInRouteFailures		2.1.351.140.1.2.5.1.1.6
This object shows the number of incoming Point-to-Point(p2p) and Point-to-MulitPoint(p2mp) SVC/SPVC call attempts on this interface which failed because there was no route to the destination available.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspInResrcFailures		2.1.351.140.1.2.5.1.1.7
This object shows the number of incoming Point-to-Point(p2p) and Point-to-MulitPoint(p2mp) SVC/SPVC call attempts on this interface which failed because there were not enough resources as requested in the parameters of the call.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspInTimerFailures		2.1.351.140.1.2.5.1.1.8
This object shows the number of signaling timers timed out for incoming Point-to-Point(p2p) and Point-to-MultiPoint(p2mp) SVC/SPVC calls on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspInCrankbacks		2.1.351.140.1.2.5.1.1.9
This object shows the number of Crankback IEs received on this interface for incoming Point-to-Point(p2p) and Point-to-MultiPoint (p2mp) SVC/SPVC call attempts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspOutCallAttempts		2.1.351.140.1.2.5.1.1.10
This object shows the number of outgoing Signaling messages (Setup and Add Party) on this interface for Call establishment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspOutCallEstabs		2.1.351.140.1.2.5.1.1.11
This object shows the number of outgoing Signaling messages (Connect and Add Party Ack) which mark the call being established on this interface
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspOutCallFailures		2.1.351.140.1.2.5.1.1.12
This object shows the total number of outgoing Signaling messages for Point-to-Point and Point-to-MultiPoint call establishment on this interface which failed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspOutFilterFailures		2.1.351.140.1.2.5.1.1.13
This object shows the number of outgoing Signaling messages for call establishment on this interface which failed the address filtering.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspOutRouteFailures		2.1.351.140.1.2.5.1.1.14
This object shows the number of outgoing Signaling messages for call establishment on this interface which failed because the route was not available.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspOutResrcFailures		2.1.351.140.1.2.5.1.1.15
This object shows the number of outgoing Signaling messages for call establishment on this interface which failed because the resource requested was not available.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspOutTimerFailures		2.1.351.140.1.2.5.1.1.16
This object shows the number of Signaling timers timed-out on this interface for outgoing signaling messages.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspOutCrankbacks		2.1.351.140.1.2.5.1.1.17
This object shows the number of Crankback IEs being sent on this interface for outgoing signaling Release messages. This is generated on the node which generates the Crankback IEs.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

cwspPrefixTable		2.1.351.140.1.2.10.1
A table specifying the network prefix(es) used for ILMI address registration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspPrefixEntry

cwspPrefixEntry		2.1.351.140.1.2.10.1.1
Information about a single network prefix contained in the prefix table.
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspPrefixEntry

cwspNetPrefix		2.1.351.140.1.2.10.1.1.1
The network prefix specified for use in ILMI address registration.
Status: current	Access: not-accessible
OBJECT-TYPE
	NetPrefix

cwspPrefixRowStatus		2.1.351.140.1.2.10.1.1.2
Used to create, delete, activate and de-activate network prefixes used in ILMI address registration.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

cwspAddressTable		2.1.351.140.1.2.11.1
The Interface ATM Address Table. This table contains all the attributes necessary to determine what the PNNI entity believes is reachable in terms of ATM End System Addresses and to determine which nodes are advertising this reachability. This table is also used to configure static routes to reachable addresses. Entries in this table can be created/deleted by setting the intfAddressRowStatus object to appropriate values. Existing entries in this table cannot be modified. Entries in this table can also be created/deleted through the command provided by the CLI.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspAddressEntry

cwspAddressEntry		2.1.351.140.1.2.11.1.1
An entry in the table, containing information about a reachable address.
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspAddressEntry

cwspAtmAddress		2.1.351.140.1.2.11.1.1.1
The value of the ATM End System Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmAddress

cwspAddrLen		2.1.351.140.1.2.11.1.1.2
The address length in bits to be applied to the ATM End System Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..160

cwspAddrType		2.1.351.140.1.2.11.1.1.3
The type of reachability from the advertising node to the address. This variable indicates either this ATM address ('internal') is a reachable ATM destination that is directly attached to the logical node advertising this address or an ATM address('exterior') that can be reached through a PNNI routing domain but which is not located in that routing domain.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	internal(1), exterior(2)

cwspAddrProto		2.1.351.140.1.2.11.1.1.4
The routing mechanism via which the connectivity from the advertising node to the reachable address was learned. A 'local' address indicates this address is automatically advertised. A 'static' address is not automatically advertised. By setting 'cwspAddrRedistribute' variable (see below) to 'true' will force a 'static' address to be advertised.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	local(1), static(2)

cwspAddrPlan		2.1.351.140.1.2.11.1.1.5
The address plan. For NSAP address, the first byte of the address automatically implies one of the three NSAP address plans: NSAP E.164, NSAP DCC or NSAP ICD.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	e164(1), nsap(2)

cwspAddrScope		2.1.351.140.1.2.11.1.1.6
The PNNI scope of advertisement (i.e. level of PNNI hierarchy) of the reachability from the advertising node to the address.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..104

cwspAddrRedistribute		2.1.351.140.1.2.11.1.1.7
Whether or not the reachable address specified by this entry is to be advertised by the local node into its PNNI routing domain. This object is only meaningful if the routing mechanism (cwspAddrProto) is static.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cwspAddressRowStatus		2.1.351.140.1.2.11.1.1.8
To create or delete a reachable address. Note that NMS should use CreateAndGo to create a row and Destroy to delete a row. The managed device will return active or notInService as row status.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

cwspRegAddressTable		2.1.351.140.1.2.12.1
This table contains a list of ATM addresses that can be used for calls to and from a given interface by a switch or service. The ATM addresses are registered by the endsystem via ILMI. ILMI registered addresses cannot be deleted using this table. This table only applies to switches and network services.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspRegAddressEntry

cwspRegAddressEntry		2.1.351.140.1.2.12.1.1
An entry in the ATM Interface Registered Address table.
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspRegAddressEntry

cwspRegAtmAddress		2.1.351.140.1.2.12.1.1.1
An address registered for a given switch or service interface.
Status: current	Access: read-only
OBJECT-TYPE
	AtmAddress

cwspRegAddressOrgSscope		2.1.351.140.1.2.12.1.1.2
This object indicates the organizational scope for the referenced address. The information of the referenced address shall not be distributed outside the indicated scope. The default values for organizational scope are localNetwork(1) for ATM group addresses, and global(15) for individual addresses.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	localNetwork(1), global(15)

cwspCacConfigTable		2.1.351.140.1.2.2.1
A table specifying the CAC(Connection Admission Control) information for each interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspCacConfigEntry

cwspCacConfigEntry		2.1.351.140.1.2.2.1.1
An entry contains CAC information.
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspCacConfigEntry

cwspUtilFactorCbr		2.1.351.140.1.2.2.1.1.1
This is the booking factor for CBR service.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..200

cwspUtilFactorRtVbr		2.1.351.140.1.2.2.1.1.2
This is the booking factor for real time VBR service
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..200

cwspUtilFactorNrtVbr		2.1.351.140.1.2.2.1.1.3
This is the booking factor for non-real time VBR service
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..200

cwspUtilFactorAbr		2.1.351.140.1.2.2.1.1.4
This is the booking factor for ABR service
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..200

cwspUtilFactorUbr		2.1.351.140.1.2.2.1.1.5
This is the booking factor for UBR service.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..200

cwspMaxBwCbr		2.1.351.140.1.2.2.1.1.6
This is the maximum bandwidth for CBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxBwRtVbr		2.1.351.140.1.2.2.1.1.7
This is the maximum bandwidth for real time VBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxBwNrtVbr		2.1.351.140.1.2.2.1.1.8
This is the maximum bandwidth for non-real time VBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxBwAbr		2.1.351.140.1.2.2.1.1.9
This is the maximum bandwidth for ABR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxBwUbr		2.1.351.140.1.2.2.1.1.10
This is the maximum bandwidth for UBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMinBwCbr		2.1.351.140.1.2.2.1.1.11
This is the minimum bandwidth for CBR service in percentage. The total values of cwspMinBwCbr, cwspMinBwRtVbr, cwspMinBwNrtVbr, cwspMinBwAbr and cwspMinBwUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMinBwRtVbr		2.1.351.140.1.2.2.1.1.12
This is the minimum bandwidth for real time VBR service in percentage. The total values of cwspMinBwCbr, cwspMinBwRtVbr, cwspMinBwNrtVbr, cwspMinBwAbr and cwspMinBwUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMinBwNrtVbr		2.1.351.140.1.2.2.1.1.13
This is the minimum bandwidth for non-real time VBR service in percentage. The total values of cwspMinBwCbr, cwspMinBwRtVbr, cwspMinBwNrtVbr, cwspMinBwAbr and cwspMinBwUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMinBwAbr		2.1.351.140.1.2.2.1.1.14
This is the minimum bandwidth for ABR service in percentage. The total values of cwspMinBwCbr, cwspMinBwRtVbr, cwspMinBwNrtVbr, cwspMinBwAbr and cwspMinBwUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMinBwUbr		2.1.351.140.1.2.2.1.1.15
This is the minimum bandwidth for UBR service in percentage. The value for this variable is always 0.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxVcCbr		2.1.351.140.1.2.2.1.1.16
This is the maximum number of VCs for CBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxVcRtVbr		2.1.351.140.1.2.2.1.1.17
This is the maximum number of VCs for real time VBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxVcNrtVbr		2.1.351.140.1.2.2.1.1.18
This is the maximum number of VCs for non-real time VBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxVcAbr		2.1.351.140.1.2.2.1.1.19
This is the maximum number of VCs for ABR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxVcUbr		2.1.351.140.1.2.2.1.1.20
This is the maximum number of VCs for UBR service in percentage. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMinVcCbr		2.1.351.140.1.2.2.1.1.21
This is the minimum number of VCs for CBR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr, cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. This variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMinVcRtVbr		2.1.351.140.1.2.2.1.1.22
This is the minimum number of VCs for real time VBR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr, cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMinVcNrtVbr		2.1.351.140.1.2.2.1.1.23
This is the minimum number of VCs for non-real time VBR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr,cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMinVcAbr		2.1.351.140.1.2.2.1.1.24
This is the minimum number of VCs for ABR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr, cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMinVcUbr		2.1.351.140.1.2.2.1.1.25
This is the minimum number of VCs for UBR service in percentage. The values of cwspMinVcCbr, cwspMinVcRtVbr, cwspMinVcNrtVbr, cwspMinVcAbr and cwspMinVcUbr can not exceed 1000000, i.e. 100%. The value of this variable is interpreted in the format of xxx.xxxx. For example a value of 750000 is interpreted as 75.0000%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxVcBwCbr		2.1.351.140.1.2.2.1.1.26
This is the maximum bandwidth allowed for a VC for real time CBR service. The value is in the unit of cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxVcBwRtVbr		2.1.351.140.1.2.2.1.1.27
This is the maximum bandwidth allowed for a VC for real time VBR service. The value is in the unit of cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxVcBwNrtVbr		2.1.351.140.1.2.2.1.1.28
This is the maximum bandwidth allowed for a VC for non-real time VBR service. The value is in the unit of cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxVcBwAbr		2.1.351.140.1.2.2.1.1.29
This is the maximum bandwidth allowed for a VC for ABR service. The value is in the unit of cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspMaxVcBwUbr		2.1.351.140.1.2.2.1.1.30
This is the maximum bandwidth allowed for UBR service. The value is in the unit of cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

cwspDefaultCdvtCbr		2.1.351.140.1.2.2.1.1.31
This is the default CDVT for CBR service.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspDefaultCdvtRtVbr		2.1.351.140.1.2.2.1.1.32
This is the default CDVT real time VBR service.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspDefaultCdvtNrtVbr		2.1.351.140.1.2.2.1.1.33
This is the default CDVT non-real time VBR service.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspDefaultCdvtAbr		2.1.351.140.1.2.2.1.1.34
This is the default CDVT for ABR service.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspDefaultCdvtUbr		2.1.351.140.1.2.2.1.1.35
This is the default CDVT for UBR service.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspDefaultMbsRtVbr		2.1.351.140.1.2.2.1.1.36
This is the default MBS real time VBR service.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspDefaultMbsNrtVbr		2.1.351.140.1.2.2.1.1.37
This is the default MBS non-real time VBR service.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadTable		2.1.351.140.1.2.13.1
A table specifying the load information for each interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspLoadEntry

cwspLoadEntry		2.1.351.140.1.2.13.1.1
An entry contains the load information.
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspLoadEntry

cwspLoadBwTotal		2.1.351.140.1.2.13.1.1.1
The total bandwidth of the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadMaxBwCbr		2.1.351.140.1.2.13.1.1.2
The Maximum bandwith for CBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadMaxBwRtVbr		2.1.351.140.1.2.13.1.1.3
The maximum bandwith for real time VBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadMaxBwNrtVbr		2.1.351.140.1.2.13.1.1.4
The maximum bandwith for non-real time VBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadMaxBwAbr		2.1.351.140.1.2.13.1.1.5
The maximum bandwith for ABR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadMaxBwUbr		2.1.351.140.1.2.13.1.1.6
The maximum bandwith for UBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadBwAvail		2.1.351.140.1.2.13.1.1.7
The total available bandwidth of the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadAvlBwCbr		2.1.351.140.1.2.13.1.1.8
The available bandwith for CBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadAvlBwRtVbr		2.1.351.140.1.2.13.1.1.9
The available bandwith for real time VBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadAvlBwNrtVbr		2.1.351.140.1.2.13.1.1.10
The available bandwith for non-real time VBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadAvlBwAbr		2.1.351.140.1.2.13.1.1.11
The available bandwith for ABR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadAvlBwUbr		2.1.351.140.1.2.13.1.1.12
The available bandwith for UBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadVcAvail		2.1.351.140.1.2.13.1.1.13
The total number of available VCs of the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadAvlVcCbr		2.1.351.140.1.2.13.1.1.14
The number of VCs used by CBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadAvlVcRtVbr		2.1.351.140.1.2.13.1.1.15
The number of VCs used by real time VBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadAvlVcNrtVbr		2.1.351.140.1.2.13.1.1.16
The number of VCs used by non-real time VBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadAvlVcAbr		2.1.351.140.1.2.13.1.1.17
The number of VCs used by ABR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadAvlVcUbr		2.1.351.140.1.2.13.1.1.18
The number of VCs used by UBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadCtdCbr		2.1.351.140.1.2.13.1.1.19
The cell transfer delay of CBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadCtdRtVbr		2.1.351.140.1.2.13.1.1.20
The cell transfer delay of real time VBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadCtdNrtVbr		2.1.351.140.1.2.13.1.1.21
The cell transfer delay of non-real time VBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadCtdAbr		2.1.351.140.1.2.13.1.1.22
The cell transfer delay of ABR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadCtdUbr		2.1.351.140.1.2.13.1.1.23
The cell transfer delay of UBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadCdvCbr		2.1.351.140.1.2.13.1.1.24
The cell delay variation of CBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadCdvRtVbr		2.1.351.140.1.2.13.1.1.25
The cell delay variation of real time VBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadCdvNrtVbr		2.1.351.140.1.2.13.1.1.26
The cell delay variation of non-real time VBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadCdvAbr		2.1.351.140.1.2.13.1.1.27
The cell delay variation of ABR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadCdvUbr		2.1.351.140.1.2.13.1.1.28
The cell delay variation of UBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadClr0Cbr		2.1.351.140.1.2.13.1.1.29
The cell loss ratio-0 of CBR service, -1 implies N/A.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadClr0RtVbr		2.1.351.140.1.2.13.1.1.30
The cell loss ratio-0 of real time VBR service, -1 implies N/A.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadClr0NrtVbr		2.1.351.140.1.2.13.1.1.31
The cell loss ratio-0 of non-real time VBR service, -1 implies N/A.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadClr0Abr		2.1.351.140.1.2.13.1.1.32
The cell loss ratio-0 of ABR service, -1 implies N/A.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadClr0Ubr		2.1.351.140.1.2.13.1.1.33
The cell loss ratio-0 of UBR service, -1 implies N/A.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadClr01Cbr		2.1.351.140.1.2.13.1.1.34
The cell loss ratio-1 of CBR service, -1 implies N/A.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadClr01RtVbr		2.1.351.140.1.2.13.1.1.35
The cell loss ratio-1 of real time VBR service, -1 implies N/A.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadClr01NrtVbr		2.1.351.140.1.2.13.1.1.36
The cell loss ratio-1 of non-real time VBR service, -1 implies N/A.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadClr01Abr		2.1.351.140.1.2.13.1.1.37
The cell loss ratio-1 of ABR service, -1 implies N/A.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadClr01Ubr		2.1.351.140.1.2.13.1.1.38
The cell loss ratio-1 of UBR service, -1 implies N/A.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadMinGurCrCbr		2.1.351.140.1.2.13.1.1.39
The minimum guaranteed cell rate capacity of CBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadMinGurCrRtVbr		2.1.351.140.1.2.13.1.1.40
The minimum guaranteed cell rate capacity of real time VBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadMinGurCrNrtVbr		2.1.351.140.1.2.13.1.1.41
The minimum guaranteed cell rate capacity of non-real time VBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadMinGurCrAbr		2.1.351.140.1.2.13.1.1.42
The minimum guaranteed cell rate capacity of ABR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspLoadMinGurCrUbr		2.1.351.140.1.2.13.1.1.43
The minimum guaranteed cell rate capacity of UBR service.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallTable		2.1.351.140.1.2.8.1
This Table contains the objects which show parameters associated with a Point-to-Point(p2p) or Point-to-MultiPoint (p2mp) SVC/SPVC call.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspCallEntry

cwspCallEntry		2.1.351.140.1.2.8.1.1
This object shows the multiple key index to get the Call record information. The key comprise of Interface Index, VPI/VCI value and Call Reference Value for the call.
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspCallEntry

cwspCallVpi		2.1.351.140.1.2.8.1.1.1
This object shows the VPI value of the call on this interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..4095

cwspCallVci		2.1.351.140.1.2.8.1.1.2
This object shows The VCI value of the call on this interface. The value should be in the range of 32-65535 (0=SPVP).
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..65535

cwspCallLeafReference		2.1.351.140.1.2.8.1.1.3
This object shows the value of the Leaf Reference (EndPointReference) of the Call on this interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..65535

cwspCallCallRef		2.1.351.140.1.2.8.1.1.4
This object shows the Call Reference value of the call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallCallingAddress		2.1.351.140.1.2.8.1.1.5
This object shows the Calling Party Address of the call.
Status: current	Access: read-only
OBJECT-TYPE
	AtmAddress

cwspCallCalledAddress		2.1.351.140.1.2.8.1.1.6
This object shows the Called Party Address of the call.
Status: current	Access: read-only
OBJECT-TYPE
	AtmAddress

cwspCallCallingSubAddr		2.1.351.140.1.2.8.1.1.7
This object shows the Calling Party Subaddress of the call.
Status: current	Access: read-only
OBJECT-TYPE
	AtmAddress

cwspCallCalledSubAddr		2.1.351.140.1.2.8.1.1.8
This object shows the Called Party Subaddress of the call.
Status: current	Access: read-only
OBJECT-TYPE
	AtmAddress

cwspCallOtherIntfIndex		2.1.351.140.1.2.8.1.1.9
This object shows the Other Interface of the call. Generally, this would be the outgoing/egress interface for the call.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallOtherIntfVpi		2.1.351.140.1.2.8.1.1.10
This object shows the VPI of the call on the partner interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4095

cwspCallOtherIntfVci		2.1.351.140.1.2.8.1.1.11
This object shows The VCI of the call on the partner o interface. The value should be in the range of 32-65535 (0=SPVP).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

cwspCallOtherIntfCallRef		2.1.351.140.1.2.8.1.1.12
This object shows the Call Reference of the call on the partner interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallType		2.1.351.140.1.2.8.1.1.13
This object shows the Call Type for the call on this interface. The call type could be SVC or SPVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	svc(1), spvc(2)

cwspCallStartTime		2.1.351.140.1.2.8.1.1.14
This object shows the start time of the call. This is the timestamp when the Setup Message (or Add Party Message) was first received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

cwspCallBearerClass		2.1.351.140.1.2.8.1.1.15
This object shows the Bearer Class of the Call. It could be BcobA, BcobC, BcobX or VP Service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	bcobA(1), bcobC(2), bcobX(3), vp(4)

cwspCallServiceCategory		2.1.351.140.1.2.8.1.1.16
This object shows the service category of the call, which can be CBR, rtVBR, nrtVBR, ABR or UBR
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cbr(1), rtVbr(2), nrtVbr(3), abr(4), ubr(5)

cwspCallCastType		2.1.351.140.1.2.8.1.1.17
This object shows the Cast Type of the call, which can be a Point-to-Point (p2p), Point-to-MultiPoint (p2mp) or MultiPoint-to-Point (mp2p) call.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	p2p(1), p2mp(2), mp2p(3)

cwspCallClipSusceptibility		2.1.351.140.1.2.8.1.1.18
This object shows Susceptibility to Clipping. It can be susceptible or not susceptible.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	yes(1), no(2)

cwspCallFwdConformance		2.1.351.140.1.2.8.1.1.19
This object shows the conformance of the call to the traffic sets in the forward direction. It can be CBR.1, CBR.2, CBR.3, VBR.1 VBR.2, VBR.3, ABR, UBR.1 or UBR.2. This is as defined in ATMF Traffic Management 4.0 specification.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cbr1(1), cbr2(2), cbr3(3), vbr1(4), vbr2(5), vbr3(6), abr(7), ubr1(8), ubr2(9)

cwspCallFwdPcr		2.1.351.140.1.2.8.1.1.20
This object shows the Peak Cell Rate(pcr) in the forward direction of the call.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallFwdScr		2.1.351.140.1.2.8.1.1.21
This object shows the Sustainable Cell Rate(scr) in the forward direction of the call.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallFwdMbs		2.1.351.140.1.2.8.1.1.22
This object shows the Maximum Burst Size(mbs) of the call in the forward direction.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallFwdCdvt		2.1.351.140.1.2.8.1.1.23
This object shows the Cell Delay Variation Tolerance(cdvt) in the forward direction for the call, for PCR and SCR.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallFwdFrameDiscard		2.1.351.140.1.2.8.1.1.24
This object shows if the Frame Discard is enabled or disabled in the forward direction for the call
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	yes(1), no(2)

cwspCallBwdConformance		2.1.351.140.1.2.8.1.1.25
This object shows the conformance of the call to the traffic sets in the backward direction. It can be CBR.1, CBR.2, CBR.3, VBR.1 VBR.2, VBR.3, ABR, UBR.1 or UBR.2. This is as defined in ATMF Traffic Management 4.0 specification.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cbr1(1), cbr2(2), cbr3(3), vbr1(4), vbr2(5), vbr3(6), abr(7), ubr1(8), ubr2(9)

cwspCallBwdPcr		2.1.351.140.1.2.8.1.1.26
This object shows the Peak Cell Rate in the backward direction of the call.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallBwdScr		2.1.351.140.1.2.8.1.1.27
This object shows the Sustainable Cell Rate in the backward direction of the call.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallBwdMbs		2.1.351.140.1.2.8.1.1.28
This object shows the Maximum Burst Size of the call in the backward direction.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallBwdCdvt		2.1.351.140.1.2.8.1.1.29
This object shows the Cell Delay Variation Tolerance in the backward direction for the call, for PCR and SCR.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallBwdFrameDiscard		2.1.351.140.1.2.8.1.1.30
This object shows if the Frame Discard is enabled or disabled in the backward direction for the call.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	yes(1), no(2)

cwspCallMaxCtd		2.1.351.140.1.2.8.1.1.31
This object shows the Maximum Cell Transfer Delay for the call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallMaxFwdCdv		2.1.351.140.1.2.8.1.1.32
This object shows the Maximum Cell Delay Variation in the forward direction for this call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallMaxFwdClr		2.1.351.140.1.2.8.1.1.33
This object shows the Maximum Cell Loss Ratio in the forward direction for this call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallMaxBwdCdv		2.1.351.140.1.2.8.1.1.34
This object shows the Maximum Cell Delay Variation in the backward direction for this call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspCallMaxBwdClr		2.1.351.140.1.2.8.1.1.35
This object shows the Maximum Cell Loss Ratio in the backward direction for this call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallTable		2.1.351.140.1.2.9.1
This table contains information for ABR calls on an interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspAbrCallEntry

cwspAbrCallEntry		2.1.351.140.1.2.9.1.1
An entry in the table, containing information about an ABR call.
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspAbrCallEntry

cwspAbrCallVpi		2.1.351.140.1.2.9.1.1.1
The VPI value of the ABR call on this interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..4095

cwspAbrCallVci		2.1.351.140.1.2.9.1.1.2
The VCI value of the ABR call on this interface. The value should be in the range of 32-65535 (0=SPVP).
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..65535

cwspAbrCallCallRef		2.1.351.140.1.2.9.1.1.3
The Call Reference value of the ABR call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallClgAddress		2.1.351.140.1.2.9.1.1.4
The Calling Party Address of the ABR call.
Status: current	Access: read-only
OBJECT-TYPE
	AtmAddress

cwspAbrCallCldAddress		2.1.351.140.1.2.9.1.1.5
The Called Party Address of the ABR call.
Status: current	Access: read-only
OBJECT-TYPE
	AtmAddress

cwspAbrCallClgSubAddr		2.1.351.140.1.2.9.1.1.6
The Calling Party Subaddress of the ABR call.
Status: current	Access: read-only
OBJECT-TYPE
	AtmAddress

cwspAbrCallCldSubAddr		2.1.351.140.1.2.9.1.1.7
The Called Party Subaddress of the ABR call.
Status: current	Access: read-only
OBJECT-TYPE
	AtmAddress

cwspAbrCallOtherIntfIndex		2.1.351.140.1.2.9.1.1.8
The Other Interface ID of the ABR call. Generally this would be the outgoing/egress interface for the call.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallOtherIntfVpi		2.1.351.140.1.2.9.1.1.9
The VPI value of the ABR call on the partner interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4095

cwspAbrCallOtherIntfVci		2.1.351.140.1.2.9.1.1.10
The VCI value of the ABR call on the partner interface. The value should be in the range of 32-65535 (0=SPVP).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

cwspAbrCallOtherIntfCallRef		2.1.351.140.1.2.9.1.1.11
The Call Reference of the ABR call on the partner interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallType		2.1.351.140.1.2.9.1.1.12
The Call Type for the ABR call on this interface. The call type could be SVC or SPVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	svc(1), spvc(2)

cwspAbrCallStartTime		2.1.351.140.1.2.9.1.1.13
The start time of the ABR call. This is the timestamp when the Setup Message (or Add Party Message) was first received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

cwspAbrCallBearerClass		2.1.351.140.1.2.9.1.1.14
The Bearer Class of the ABR call. It could be BCOB-A, BCOB-C, BCOB-X or VP Service.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	bcobA(1), bcobC(2), bcobX(3), vp(4)

cwspAbrCallServiceCategory		2.1.351.140.1.2.9.1.1.15
The Service Category of the ABR call, which is ABR.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	abr(4)

cwspAbrCallCastType		2.1.351.140.1.2.9.1.1.16
The Cast Type of the ABR call, which can only be Point-to-Point(p2p) call.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	p2p(1)

cwspAbrCallClipSusceptibility		2.1.351.140.1.2.9.1.1.17
Susceptibility to Clipping. It can be susceptible or not susceptible.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	yes(1), no(2)

cwspAbrCallFwdConformance		2.1.351.140.1.2.9.1.1.18
The Conformance of the ABR call to the traffic sets in the forward direction. It can only be ABR as defined in ATMF Traffic Management 4.0 specification.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	abr(7)

cwspAbrCallFwdPcr		2.1.351.140.1.2.9.1.1.19
The Peak Cell Rate for the ABR call in the forward direction.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallFwdMcr		2.1.351.140.1.2.9.1.1.20
The Minimum Cell Rate for the ABR call in the forward direction.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallFwdIcr		2.1.351.140.1.2.9.1.1.21
The Initial Cell Rate for the ABR call in the forward direction. This is the rate at which the source starts, both initially and after an idle period. The value must not be larger than PCR, and is usually lower.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallFwdRif		2.1.351.140.1.2.9.1.1.22
The Rate Increase Factor for the ABR call in the forward direction. This controls the rate at which the rate increases, when a backward RM-cell is received with CI=0 and NI=0. Larger values lead to faster rate increase. The default value is rifOneOver16(12).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	rifOneOver32768(1), rifOneOver16384(2), rifOneOver8192(3), rifOneOver4096(4), rifOneOver2048(5), rifOneOver1024(6), rifOneOver512(7), rifOneOver256(8), rifOneOver128(9), rifOneOver64(10), rifOneOver32(11), rifOneOver16(12), rifOneOver8(13), rifOneOver4(14), rifOneOver2(15), rifOne(16)

cwspAbrCallFwdRdf		2.1.351.140.1.2.9.1.1.23
The Rate Decrease Factor for the ABR call in the forward direction. This controls the rate decrease which occurs when backward RM-cells with CI=1, are received. Larger values lead to faster rate decrease. The default value is rdfOneOver16(12).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	rdfOneOver32768(1), rdfOneOver16384(2), rdfOneOver8192(3), rdfOneOver4096(4), rdfOneOver2048(5), rdfOneOver1024(6), rdfOneOver512(7), rdfOneOver256(8), rdfOneOver128(9), rdfOneOver64(10), rdfOneOver32(11), rdfOneOver16(12), rdfOneOver8(13), rdfOneOver4(14), rdfOneOver2(15), rdfOne(16)

cwspAbrCallFwdTbe		2.1.351.140.1.2.9.1.1.24
The Transient Buffer Exposure for the ABR call in the forward direction. This is the negotiated number of cells that the network would like to limit the source to sending during setup periods, before the first RM-cell returns.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallFwdNrm		2.1.351.140.1.2.9.1.1.25
The Maximum Number of Cells a source may send for each forward RM-cell in the forward direction for the ABR call. The default value is nrm32(5).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	nrm2(1), nrm4(2), nrm8(3), nrm16(4), nrm32(5), nrm64(6), nrm128(7), nrm256(8)

cwspAbrCallFwdTrm		2.1.351.140.1.2.9.1.1.26
The Upper Bound on the time between forward RM-cells in the forward direction for the ABR call.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	trm0point78125(1), trm1point5625(2), trm3point125(3), trm6point25(4), trm12point5(5), trm25(6), trm50(7), trm100(8)

cwspAbrCallFwdAdtf		2.1.351.140.1.2.9.1.1.27
The Allowed Cell Rate (ACR) Decrease Time Factor for the ABR call in the forward direction. This is the time permitted between sending RM-cells before the rate is decreased to ICR. Range is 10 ms to 10.23 seconds. The unit is 10 msecs. For example, the default value of 50 corresponds to a time factor of 500 ms. Larger values allow a source to retain its current rate longer, during periods of relative inactivity. The default is 50 (0.5 seconds).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..1023

cwspAbrCallFwdCdf		2.1.351.140.1.2.9.1.1.28
The Cutoff Decrease Factor for the ABR call in the forward direction. This controls the decrease in Allowed Cell Rate (ACR) associated with missing RM-cell count (CRM). Larger values result in faster rate decrease. The default value is cdfOneOver16(4).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cdf0(1), cdfOneOver64(2), cdfOneOver32(3), cdfOneOver16(4), cdfOneOver8(5), cdfOneOver4(6), cdfOneOver2(7), cdfOne(8)

cwspAbrCallFwdFrameDiscard		2.1.351.140.1.2.9.1.1.29
Whether Frame Discard is enabled or disabled in the forward direction for the ABR call.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	yes(1), no(2)

cwspAbrCallBwdPcr		2.1.351.140.1.2.9.1.1.30
The Peak Cell Rate for the ABR call in the backward direction.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallBwdMcr		2.1.351.140.1.2.9.1.1.31
The Minimum Cell Rate for the ABR call in the backward direction.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallBwdIcr		2.1.351.140.1.2.9.1.1.32
The Initial Cell Rate for the ABR call in the backward direction. This is the rate at which the source starts, both initially and after an idle period. The value must not be larger than PCR, and is usually lower.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallBwdRif		2.1.351.140.1.2.9.1.1.33
The Rate Increase Factor for the ABR call in the backward direction. This controls the rate at which the rate increases, when a forward RM-cell is received with CI=0 and NI=0. Larger values lead to faster rate increase. The default value is rifOneOver16(12).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	rifOneOver32768(1), rifOneOver16384(2), rifOneOver8192(3), rifOneOver4096(4), rifOneOver2048(5), rifOneOver1024(6), rifOneOver512(7), rifOneOver256(8), rifOneOver128(9), rifOneOver64(10), rifOneOver32(11), rifOneOver16(12), rifOneOver8(13), rifOneOver4(14), rifOneOver2(15), rifOne(16)

cwspAbrCallBwdRdf		2.1.351.140.1.2.9.1.1.34
The Rate Decrease Factor for the ABR call in the backward direction. This controls the rate decrease which occurs when forward RM-cells with CI=1, are received. Larger values lead to faster rate decrease. The default value is rdfOneOver16(12).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	rdfOneOver32768(1), rdfOneOver16384(2), rdfOneOver8192(3), rdfOneOver4096(4), rdfOneOver2048(5), rdfOneOver1024(6), rdfOneOver512(7), rdfOneOver256(8), rdfOneOver128(9), rdfOneOver64(10), rdfOneOver32(11), rdfOneOver16(12), rdfOneOver8(13), rdfOneOver4(14), rdfOneOver2(15), rdfOne(16)

cwspAbrCallBwdTbe		2.1.351.140.1.2.9.1.1.35
The Transient Buffer Exposure for the ABR call in the backward direction. This is the negotiated number of cells that the network would like to limit the source to sending during setup periods, before the first RM-cell returns.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallBwdNrm		2.1.351.140.1.2.9.1.1.36
The Maximum Number of Cells a source may send for each forward RM-cell in the backward direction for the ABR call. The default value is nrm32(5).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	nrm2(1), nrm4(2), nrm8(3), nrm16(4), nrm32(5), nrm64(6), nrm128(7), nrm256(8)

cwspAbrCallBwdTrm		2.1.351.140.1.2.9.1.1.37
The Upper Bound on the time between forward RM-cells in the backward direction for the ABR call.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	trm0point78125(1), trm1point5625(2), trm3point125(3), trm6point25(4), trm12point5(5), trm25(6), trm50(7), trm100(8)

cwspAbrCallBwdAdtf		2.1.351.140.1.2.9.1.1.38
The Allowed Cell Rate (ACR) Decrease Time Factor for the ABR call in the backward direction. This is the time permitted between sending RM-cells before the rate is decreased to ICR. Range is 10 ms to 10.23 seconds. The unit is 10 msecs. For example, the default value of 50 corresponds to a time factor of 500 ms. Larger values allow a source to retain its current rate longer, during periods of relative inactivity. The default is 50 (0.5 seconds).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..1023

cwspAbrCallBwdCdf		2.1.351.140.1.2.9.1.1.39
The Cutoff Decrease Factor for the ABR call in the backward direction. This controls the decrease in Allowed Cell Rate (ACR) associated with missing RM-cell count (CRM). Larger values result in faster rate decrease. The default value is cdfOneOver16(4).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cdf0(1), cdfOneOver64(2), cdfOneOver32(3), cdfOneOver16(4), cdfOneOver8(5), cdfOneOver4(6), cdfOneOver2(7), cdfOne(8)

cwspAbrCallBwdFrameDiscard		2.1.351.140.1.2.9.1.1.40
Whether Frame Discard is enabled or disabled in the backward direction for the ABR call.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	yes(1), no(2)

cwspAbrCallFrtt		2.1.351.140.1.2.9.1.1.41
The Fixed Round-Trip Time for the ABR call. This is the sum of the fixed and propagation delays from the source to the furthest destination and back.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallMaxCtd		2.1.351.140.1.2.9.1.1.42
The Maximum Cell Transfer Delay for the ABR call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallMaxFwdCdv		2.1.351.140.1.2.9.1.1.43
The Maximum Cell Delay Variation in the forward direction for the ABR call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallMaxFwdClr		2.1.351.140.1.2.9.1.1.44
The Maximum Cell Loss Ratio in the forward direction for the ABR call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallMaxBwdCdv		2.1.351.140.1.2.9.1.1.45
The Maximum Cell Delay Variation in the backward direction for the ABR call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspAbrCallMaxBwdClr		2.1.351.140.1.2.9.1.1.46
The Maximum Cell Loss Ratio in the backward direction for the ABR call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspConnTraceAvail		2.1.351.140.1.2.14.1
This object tells the number of calls can be traced concurrently. Depending on the system resource, this object may vary sometime to time. NMS should query this object to ensure there is system resource available before creating a row in the cwspConnTraceCntlTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..100

cwspConnTraceNextIndex		2.1.351.140.1.2.14.2
When creating a row in the cwspConnTraceCntlTable, NMS should query this object to obtain the index value to be used for row creation.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

cwspConnTraceCntlTable		2.1.351.140.1.2.14.3
This Table contains the objects which control the creation of connection trace for the existing SVC call.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspConnTraceCntlEntry

cwspConnTraceCntlEntry		2.1.351.140.1.2.14.3.1
This object controls the connection trace creation. NMS needs to acquire the next index available to create a row. In addition, NMS needs to provide all read-create objects in the same pdu with RowStatus to be CreateAndGo.
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspConnTraceCntlEntry

cwspConnTraceIndex		2.1.351.140.1.2.14.3.1.1
Index to a row of connection trace.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

cwspConnTraceifIndex		2.1.351.140.1.2.14.3.1.2
The 'ifIndex' indicates the port to a trace connection.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndex

cwspConnTraceSrcVpi		2.1.351.140.1.2.14.3.1.3
This object shows the VPI value of the starting point on this interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..4095

cwspConnTraceSrcVci		2.1.351.140.1.2.14.3.1.4
This object shows The VCI value of the starting point on this interface. The value should be in the range of 32-65535 (0=SPVP).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

cwspConnTraceType		2.1.351.140.1.2.14.3.1.5
Setting this object to either p2p or p2mp to specify tracing a p2p or p2mp connection.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	p2p(1), p2mp(2)

cwspConnTraceCallRef		2.1.351.140.1.2.14.3.1.6
This object shows the Call Reference value of the call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspConnTraceLeafRef		2.1.351.140.1.2.14.3.1.7
This object shows the value of the Leaf Reference (EndPointReference) of the Call on this interface, this value is used to support p2mp call trace. For p2p call, this value should be set as 0 by NMS.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

cwspConnTraceDestVpi		2.1.351.140.1.2.14.3.1.8
This object shows the endpoint VPI value of the call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4095

cwspConnTraceDestVci		2.1.351.140.1.2.14.3.1.9
This object shows the endpoint VCI value of the call on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

cwspConnTraceDestCallRef		2.1.351.140.1.2.14.3.1.10
This object shows the endpoint call reference on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspConnTraceResultStatus		2.1.351.140.1.2.14.3.1.11
This object shows the result of tracing the call. NMS should get positive result (i.e. traceCompleted) for this attribute before query the cwspConnTraceTable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	traceInProgress(1), traceCompleted(2), traceIncompleted(3), traceExceededLength(4), traceContRefused(5), traceLackResource(6)

cwspConnTraceQueryStatus		2.1.351.140.1.2.14.3.1.12
This object used to manage rows in this table. However, only CreateAndGo, NotInService, Active, and Destroy are start up the trace. To remove a row, NMS set this value to Destroy. The managed device will either return Active or NotInService.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

cwspConnTraceTable		2.1.351.140.1.2.14.4
This table contains the objects which show the traversed node information in the existing SVC call.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspConnTraceEntry

cwspConnTraceEntry		2.1.351.140.1.2.14.4.1
A conceptual row of the cwspConnTraceTable used to return information about all the nodes belongs to the connection which search criteria is corresponding to instance of the cwspConnTraceCntlTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspConnTraceEntry

cwspConnTraceDataIndex		2.1.351.140.1.2.14.4.1.1
Along with cwspConnTraceIndex, this object specified an unique entry in the cwspConnTraceTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..100

cwspConnTraceNodeId		2.1.351.140.1.2.14.4.1.2
This octet string represents 22 bytes nodeId in the traced connection.
Status: current	Access: read-only
OBJECT-TYPE
	PnniNodeId

cwspConnTraceEgressPortId		2.1.351.140.1.2.14.4.1.3
This object represents 4 bytes logical port ID of the traversed node. When 0 is specified, the destination node for the trace is reached.
Status: current	Access: read-only
OBJECT-TYPE
	PnniPortId

cwspConnTraceEgressVpi		2.1.351.140.1.2.14.4.1.4
This object shows the Egress port's VPI value for the traced connection.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4095

cwspConnTraceEgressVci		2.1.351.140.1.2.14.4.1.5
This object shows the Egress port's VCI value for the traced connection
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

cwspConnTraceEgressCallRef		2.1.351.140.1.2.14.4.1.6
This object shows the Egress port's call reference.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

cwspConnTraceEgressPhyPortId		2.1.351.140.1.2.14.4.1.7
This object shows the Egress port's physical port Identifier for the traversed node; if this object is 0 meaning that the destination node for the traced connection has been reached. the meaning for the bytes are: first byte -- flag (used by CLI to decode the rest of bytes ) 2nd byte -- shelf 3rd & 4th bytes -- slot 5th byte -- subslot 6th & 7th bytes -- port 8th byte -- subport
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(8)

cwspConnTraceLastNode		2.1.351.140.1.2.14.4.1.8
This value indicates if this entry contains the information about the last node where this trace ends. If it is the last node, this value is 'true(1)' or it is 'false(2)'.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

ciscoWANPnniLinkStatus		2.1.351.140.1.3.1
Indicates the status of a link has changed: 1 - the link entered the 2-Way Inside state, 2 - the link exit the 2-Way Inside state, 3 - the link entered the 2-Way Outside state, 4 - the link exit the 2-Way Outside state. 5 - the link entered the Common Outside state, or 6 - the link exit the Common Outside state and entered the 1-Way Outside state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	in2win(1), out2win(2), in2wout(3), out2wout(4), inCout(5), outCout(6)

ciscoWANPnniPglStatus		2.1.351.140.1.3.2
Indicates the status of PGL process has changed: 1 - the PGL exit the hung-election state, or 2 - the PGL entered the hung-election state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), hung(2)

ciscoWANPnniReachability		2.1.351.140.1.3.3
This object is used in conjunction with ciscoWANPnniRemoteNodeId to indicate the reachability of the RemoteNode has changed: 1 - RemoteNode became reachable, or 2 - RemoteNode became unreachable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), fail(2)

ciscoWANPnniRemoteNodeId		2.1.351.140.1.3.4
Indicates the node identifier of a remote node. If the remote node ID is unknown, this attribute is set to all zeros.
Status: current	Access: read-only
OBJECT-TYPE
	PnniNodeId

ciscoWANPnniPortId		2.1.351.140.1.3.5
The port identifier of the port.
Status: current	Access: read-only
OBJECT-TYPE
	PnniPortId

cwspOperationTable		2.1.351.140.1.2.15.1
The Interface operation table contains the runtime negotiated values between platform, PNNI controller and peer on an interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CwspOperationEntry

cwspOperationEntry		2.1.351.140.1.2.15.1.1
An entry in the interface operation table containing negotiated values of an interface
Status: current	Access: not-accessible
OBJECT-TYPE
	CwspOperationEntry

cwspOperIlmiEnable		2.1.351.140.1.2.15.1.1.1
The operational state of ILMI.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

cwspOperIfcType		2.1.351.140.1.2.15.1.1.2
The interface type of an interface publicUni -- Public User-Network Interface privateUni -- Private User-Network Interface iisp -- Interim Inter-Switch Signaling Protocol pnni -- Private Network-Network Interface aini -- ATM Inter-Network Interface enni -- Enhanced Network-Network Interface, a cisco proprietary interfac type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	publicUni(1), privateUni(2), iisp(3), pnni(4), aini(5), enni(6)

cwspOperIfcSide		2.1.351.140.1.2.15.1.1.3
The IME type of the ATM device which is concluded from automatic interface type determination procedure.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	userSide(1), networkSide(2), symmetric(3)

cwspOperMaxVPCs		2.1.351.140.1.2.15.1.1.4
The maximum number of switched and permanent VPCs supported on this ATM interface
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4096

cwspOperMaxVCCs		2.1.351.140.1.2.15.1.1.5
The maximum number of switched and permanent VCCs supported on this ATM interface
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65536

cwspOperMaxVpiBits		2.1.351.140.1.2.15.1.1.6
The maximum number of active VPI bits on this ATM interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..12

cwspOperMaxVciBits		2.1.351.140.1.2.15.1.1.7
The maximum number of active VCI bits on this ATM interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..16

cwspOperUniType		2.1.351.140.1.2.15.1.1.8
The type of the ATM device, either public or private.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	public(1), private(2)

cwspOperUniVersion		2.1.351.140.1.2.15.1.1.9
An indication of the latest version of the ATM Forum UNI Signaling Specification that is supported on this ATM Interface. If this value is not present, a version of the UNI earlier than 3.1 is supported. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	version2point0(1), version3poing0(2), version3poing1(3), version4poing0(4), unsupported(5)

cwspOperDeviceType		2.1.351.140.1.2.15.1.1.10
This object determines the type of the ATM device. This object is used in automatic ATM Interface-Type determination procedure such that a correct operational ATM Interface-type can be determined. An ATM End System shall take the value of user(1), and an ATM network node shall take the value of node(2).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	user(1), node(2)

cwspOperIlmiVersion		2.1.351.140.1.2.15.1.1.11
An indication of the latest version of the ATM Forum ILMI Specification that is supported on this ATM Interface. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed. If this object is not present, a version of the ILMI earlier than 4.0 is supported.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unsupported(1), version4point0(2)

cwspOperNniSigVersion		2.1.351.140.1.2.15.1.1.12
An indication of the latest version of the ATM Forum PNNI Signaling Specification that is supported on this ATM Interface. Note that the PNNI routing version is not determined through ILMI. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed. Note that 'enni' is not a signaling protocol.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unsupported(1), iisp(2), pnniVersion1point0(3), enni(4), aini(5)

cwspOperMaxSvpcVpi		2.1.351.140.1.2.15.1.1.13
The maximum switched VPC VPI.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4095

cwspOperMinSvpcVpi		2.1.351.140.1.2.15.1.1.14
The minimum switched VPC VPI.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4095

cwspOperMaxSvccVpi		2.1.351.140.1.2.15.1.1.15
The maximum switched VCC VPI.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4095

cwspOperMinSvccVpi		2.1.351.140.1.2.15.1.1.16
The minimum switched VCC VPI.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4095

cwspOperMaxSvccVci		2.1.351.140.1.2.15.1.1.17
The maximum switched VCC VCI.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	35..65535

cwspOperMinSvccVci		2.1.351.140.1.2.15.1.1.18
The minimum switched VCC VCI.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

cwspOperAddrPlanSupported		2.1.351.140.1.2.15.1.1.19
The ATM address plan supported on a public UNI. For all other interfaces, the value is aesa.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	both(1), aesa(2), e164(3)

cwspOperFailReason		2.1.351.140.1.2.15.2
Defined SVC port failures. Note: this object is used as trap varbind only. The NMS applications should not issue SNMP get, get-next for this object.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ilmiDown(1), portDown(2), vsiOperDown(3), vccfailure(4), neighIpChanged(5), vsiRemove(6), vsiAdminDown(7)

ciscoWANSpvcFailReason		2.1.351.140.1.4.1
Defines SPVC manager failures. Refer description in the textual convention. Note: this object is for Supporting Varbinds used only in trap definitions. The NMS applications should not depend on the implementation of this object. The SNMP Requests(GET,GET-NEXT) is not valid for this object.
Status: current	Access: read-only
OBJECT-TYPE
	CwspSpvcState

cwspSpvcNodePrefix		2.1.351.140.1.4.2
Spvc node prefix for the pnni controller. This node prefix identifies an SPVC node in the network.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(13)

ciscoWANSvcMIBConformance		2.1.351.140.3
OBJECT IDENTIFIER

ciscoWANSvcMIBCompliances		2.1.351.140.3.1
OBJECT IDENTIFIER

ciscoWANSvcMIBGroups		2.1.351.140.3.2
OBJECT IDENTIFIER

ciscoWANSvcMIBCompliance		2.1.351.140.3.1.1
The compliance statement for entities that support the Cisco SVC MIB.
Status: deprecated	Access: read-only
MODULE-COMPLIANCE

ciscoWANSvcMIBCompliance2		2.1.351.140.3.1.2
The compliance statement for entities that support the Cisco SVC MIB.
Status: deprecated	Access: read-only
MODULE-COMPLIANCE

ciscoWANSvcMIBCompliance3		2.1.351.140.3.1.3
The compliance statement for entities that support the Cisco SVC MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

cwsInfoGrp		2.1.351.140.3.2.1
A collection of objects providing device level information.
Status: current	Access: read-only
OBJECT-GROUP

cwspConfigGrp		2.1.351.140.3.2.2
A collection of objects providing information about the controller interface operation and associated parameters.
Status: deprecated	Access: read-only
OBJECT-GROUP

cwspCacConfigGrp		2.1.351.140.3.2.3
A collection of objects providing information about CAC information of a interface.
Status: current	Access: read-only
OBJECT-GROUP

cwspCallStatsGrp		2.1.351.140.3.2.4
A collection of objects providing information about call statistics of a interface.
Status: current	Access: read-only
OBJECT-GROUP

cwspSigStatsGrp		2.1.351.140.3.2.5
A collection of objects providing information about signaling statistics.
Status: current	Access: read-only
OBJECT-GROUP

cwspCallGrp		2.1.351.140.3.2.6
A collection of objects providing information about the p2p or p2mp SVC/SPVC calls and associated parameters.
Status: current	Access: read-only
OBJECT-GROUP

cwspAbrCallGrp		2.1.351.140.3.2.7
A collection of objects providing information about ABR calls and associated parameters of a interface.
Status: current	Access: read-only
OBJECT-GROUP

cwspPrefixGrp		2.1.351.140.3.2.8
A table specifying the network prefix(es) used for ILMI address registration.
Status: current	Access: read-only
OBJECT-GROUP

cwspLoadGrp		2.1.351.140.3.2.9
A collection of objects providing information about load information and associated parameters of a interface.
Status: current	Access: read-only
OBJECT-GROUP

cwspAddressGrp		2.1.351.140.3.2.10
A collection of objects providing information about ATM End System Addresses.
Status: current	Access: read-only
OBJECT-GROUP

cwspSigConfigGrp		2.1.351.140.3.2.11
A collection of objects providing information about signaling configuration and associated parameters.
Status: current	Access: read-only
OBJECT-GROUP

cwspSscopConfigGrp		2.1.351.140.3.2.12
A collection of objects providing information about SSCOP configuration and associated parameters.
Status: current	Access: read-only
OBJECT-GROUP

cwspSscopStatsGrp		2.1.351.140.3.2.13
A collection of objects providing information about SSCOP statistics.
Status: current	Access: read-only
OBJECT-GROUP

cwspRegAddressGrp		2.1.351.140.3.2.14
A collection of objects providing information about registed ATM address.
Status: current	Access: read-only
OBJECT-GROUP

cwspRoutingGrp		2.1.351.140.3.2.15
A collection of objects providing information about PNNI topology.
Status: current	Access: read-only
OBJECT-GROUP

cwspConnTraceGrp		2.1.351.140.3.2.16
A collection of objects providing trace information about SVC/PNNI connnection.
Status: deprecated	Access: read-only
OBJECT-GROUP

cwspOperationGrp		2.1.351.140.3.2.17
A collection of objects providing information about runtime negotiated values between platform, PNNI controller and peer on an interface.
Status: current	Access: read-only
OBJECT-GROUP

cwspSpvcGrp		2.1.351.140.3.2.18
A collection of objects providing spvc related information in pnni controller.
Status: current	Access: read-only
OBJECT-GROUP

cwspConnTraceGrp2		2.1.351.140.3.2.19
A collection of objects providing trace information about SVC/PNNI connnection.
Status: current	Access: read-only
OBJECT-GROUP

cwspConfigGrp2		2.1.351.140.3.2.20
A collection of objects providing information about the controller interface operation and associated parameters.
Status: deprecated	Access: read-only
OBJECT-GROUP

cwspConfigGrp3		2.1.351.140.3.2.21
A collection of objects providing information about the controller interface operation and associated parameters.
Status: current	Access: read-only
OBJECT-GROUP