CISCO-WAN-FEEDER-MIB

File: CISCO-WAN-FEEDER-MIB.mib (11578 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB CISCOWAN-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE IpAddress
Integer32 RowStatus DisplayString
MODULE-COMPLIANCE OBJECT-GROUP InterfaceIndex
ciscoWan

Defined Types

CwfFeederEntry  
SEQUENCE    
  cwfFeederIfNum InterfaceIndex
  cwfFeederName DisplayString
  cwfLanIP IpAddress
  cwfNetIP IpAddress
  cwfRemoteShelf Integer32
  cwfRemoteSlot Integer32
  cwfRemotePort Integer32
  cwfFeederType INTEGER
  cwfModelNumber Integer32
  cwfLMIAdminStatus INTEGER
  cwfLMIOperStatus INTEGER
  cwfFeederNodeAlarm INTEGER
  cwfFeederRowStatus RowStatus
  cwfLMIType INTEGER

Defined Values

ciscoWanFeederMIB 1.3.6.1.4.1.351.150.15
This MIB is used for configuring a port on an ATM switch module to be aware of feeder connection information. Terminology: AR - Auto Route, a CISCO proprietary feature, provides connection management for network with only CISCO nodes such as BPX or IGX. Feeder - An external ATM switch, which does not have PNNI feature, connected to an ATM switch that supports PNNI to provide LMI. LMI - Local Management Interface is an interface to provide a set of enhancements to Frame Relay specification for managing complex internetworks. LMI extensions include global addressing, virtual-circuit status messages, and multicasting. XLMI - The Extended LMI is a type of LMI which is implemented in an AR + PNNI network.
MODULE-IDENTITY    

cwfMIBObjects 1.3.6.1.4.1.351.150.15.1
OBJECT IDENTIFIER    

cwfFeeder 1.3.6.1.4.1.351.150.15.1.1
OBJECT IDENTIFIER    

cwfFeederTable 1.3.6.1.4.1.351.150.15.1.1.1
This table contains the entries for the feeders. It is used for addition or deletion of feeders and to support LMI on the feeders. The information in these entries are advertised to LMI using a system dependent implementation when an entry is created/activated. This table can also be applicable to XLMI.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwfFeederEntry

cwfFeederEntry 1.3.6.1.4.1.351.150.15.1.1.1.1
An entry in cwfFeederTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CwfFeederEntry  

cwfFeederIfNum 1.3.6.1.4.1.351.150.15.1.1.1.1.1
This is an unique interface number of an ATM virtual interface. The value of this object is equal to the ifIndex of the ATM virtual interface interface identified by ifType atmVirtual(149).
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

cwfFeederName 1.3.6.1.4.1.351.150.15.1.1.1.1.2
This is the name of the feeder. It contains a string of length zero, if the feeder name is not available.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

cwfLanIP 1.3.6.1.4.1.351.150.15.1.1.1.1.3
This is the LAN IP address of the feeder. This IP address is used for ethernet interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

cwfNetIP 1.3.6.1.4.1.351.150.15.1.1.1.1.4
This is the network IP address of the feeder. This IP address is used for ATM interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

cwfRemoteShelf 1.3.6.1.4.1.351.150.15.1.1.1.1.5
This is the remote shelf number of the feeder module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..4  

cwfRemoteSlot 1.3.6.1.4.1.351.150.15.1.1.1.1.6
This is the remote slot number of the feeder module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..32  

cwfRemotePort 1.3.6.1.4.1.351.150.15.1.1.1.1.7
This is the remote physical port(line) number of the feeder module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..64  

cwfFeederType 1.3.6.1.4.1.351.150.15.1.1.1.1.8
This identifies the feeeder type. fdrNON(12) is applicable when cwfLMIType is xLMI(2). Other values are applicable for cwfLMIType = feeder(1). The possible values are: fdrIPX -- Feeder is an IPX node in a routing network fdrBPX -- Feeder is an BPX node in a routing network fdrIpxAF -- Feeder is a stand-alone IPX node fdrBASIS -- Feeder is a stand-alone BASIS node fdrUNKNOWN -- Feeder is unknown fdrUNI -- Feeder is a UNI AIT (phase 0) fdrAPS -- Feeder is an APS (Adjunct Processor Shelf) fdrIGX -- Feeder is an IGX node in a routing network fdrIgxAF -- Feeder is a stand-alone IGX node fdrVSI -- Feeder is an VSI Controller fdrPAR -- Feeder is a PAR fdrNON -- Non-feeder type
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER fdrIPX(1), fdrBPX(2), fdrIpxAF(3), fdrBASIS(4), fdrUNKNOWN(5), fdrUNI(6), fdrAPS(7), fdrIGX(8), fdrIgxAF(9), fdrVSI(10), fdrPAR(11), fdrNON(12)  

cwfModelNumber 1.3.6.1.4.1.351.150.15.1.1.1.1.9
This identifies the feeder model number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

cwfLMIAdminStatus 1.3.6.1.4.1.351.150.15.1.1.1.1.10
This provides the feeder LMI admin state configuration capabilities for the desired state of interface. The value of this object is ignored during row creation.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

cwfLMIOperStatus 1.3.6.1.4.1.351.150.15.1.1.1.1.11
This provides the operational state of the LMI connection.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

cwfFeederNodeAlarm 1.3.6.1.4.1.351.150.15.1.1.1.1.12
This identifies the feeder node alarm status. It provides the alarm status in hierarchical order where by if there are no feeder node alarms, it is signified by . If minor alarms, with no major alarms, it is signified by . If the node has one or more major alarms, irrespective of the minor alarm status, then it is signified by .
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER clear(1), minor(2), major(3), critical(4), unknown(5)  

cwfFeederRowStatus 1.3.6.1.4.1.351.150.15.1.1.1.1.13
This is used for adding or deleting a feeder entry. The row can be created by setting this object to 'createAndGo(4)'. The row can be deleted by setting this object to 'destroy(6)'. No other values are supported.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cwfLMIType 1.3.6.1.4.1.351.150.15.1.1.1.1.14
This identifies the LMI type. It identifies the type of network to which the LMI port is connected to.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER feeder(1), xLMI(2)  

cwfMIBConformance 1.3.6.1.4.1.351.150.15.3
OBJECT IDENTIFIER    

cwfMIBCompliances 1.3.6.1.4.1.351.150.15.3.1
OBJECT IDENTIFIER    

cwfMIBGroups 1.3.6.1.4.1.351.150.15.3.2
OBJECT IDENTIFIER    

cwfMIBCompliance 1.3.6.1.4.1.351.150.15.3.1.1
The compliance statement for feeder group.
Status: deprecated Access: read-create
MODULE-COMPLIANCE    

cwfMIBCompliance2 1.3.6.1.4.1.351.150.15.3.1.2
The Compliance statement for feeder group.
Status: current Access: read-create
MODULE-COMPLIANCE    

cwfFeederGroup 1.3.6.1.4.1.351.150.15.3.2.1
The objects related to configuring a feeder.
Status: deprecated Access: read-create
OBJECT-GROUP    

cwfFeederGroup2 1.3.6.1.4.1.351.150.15.3.2.2
The objects related to configuring feeder and non-feeder(XLMI).
Status: current Access: read-create
OBJECT-GROUP