CISCO-VOICE-DIAL-CONTROL-MIB

File: CISCO-VOICE-DIAL-CONTROL-MIB.mib (283262 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
DIAL-CONTROL-MIB INT-SERV-MIB IF-MIB
INET-ADDRESS-MIB SNMP-FRAMEWORK-MIB CISCO-DIAL-CONTROL-MIB
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB CISCO-VOICE-DNIS-MIB CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
IpAddress Gauge32 Integer32
Unsigned32 Counter32 MODULE-COMPLIANCE
OBJECT-GROUP NOTIFICATION-GROUP TEXTUAL-CONVENTION
DisplayString RowStatus TruthValue
TimeStamp PhysAddress DateAndTime
callActiveSetupTime callActiveIndex AbsoluteCounter32
callActivePeerAddress callActivePeerId QosService
ifIndex InterfaceIndexOrZero InetAddressType
InetAddress SnmpAdminString cCallHistoryIndex
cCallHistoryCallOrigin CvcSpeechCoderRate CvcFaxTransmitRate
CvcCoderTypeRate CvcGUid CvcInBandSignaling
cvCommonDcCallHistoryCoderTypeRate CvcCallReferenceIdOrZero DnisMapname
ciscoMgmt

Defined Types

CvCallVolumeWMIntvlType  
Represents the Id of the watermark table. Here is what different values represent 1 : Seconds Table: Here the entries are among last 60 second 2 : Minutes Table: Here the entries are among last 60 minutes 3 : Hours Table: Here the entries are among last 72 Hours 4 : Uptime Table: Here the entries are from last reload/reboot
TEXTUAL-CONVENTION    
  INTEGER secondStats(1), minuteStats(2), hourStats(3), fromReloadStats(4)  

CvCallVolumeStatsIntvlType  
Represents the ids of the stats vlolume table Here is what each entry corresponds. 1 : Seconds Table: Here each entry corresponds to a second 2 : Minutes Table: Here each entry corresponds to a minute 3 : Hours Table: Here each entry corresponds to an hour
TEXTUAL-CONVENTION    
  INTEGER secondStats(1), minuteStats(2), hourStats(3)  

CvSessionProtocol  
Represents a Session Protocol used by Voice calls between a local and remote router via the IP backbone. other - none of the following. cisco - cisco proprietary H.323 Lite session protocol. sdp - Session Description Protocol. sip - Session Initiation Protocol. sccp - Skinny Call Control Protocol.
TEXTUAL-CONVENTION    
  INTEGER other(1), cisco(2), sdp(3), sip(4), multicast(5), sccp(6)  

CvCasGroup  
The Channel Associated Signalling Group of a T1/E1. The valid CAS group range is from 0 to 23 for T1 and from 0 to 30 for E1. The value -1 indicates CAS group is disabled.
TEXTUAL-CONVENTION    
  Integer32 -1..30  

CvAmrNbBitRateMode  
Represents GSM AMR-NB bit rate modes. CodecMode Bit-rate (kbps) 0 4.75 1 5.15 2 5.90 3 6.70 4 7.40 5 7.95 6 10.2 7 12.2
TEXTUAL-CONVENTION    
  BITS amrBitRateMode0(0), amrBitRateMode1(1), amrBitRateMode2(2), amrBitRateMode3(3), amrBitRateMode4(4), amrBitRateMode5(5), amrBitRateMode6(6), amrBitRateMode7(7)  

CvAmrNbRtpEncap  
Represents GSM AMR-NB codec RTP encapsulation type.
TEXTUAL-CONVENTION    
  INTEGER rfc3267(1)  

CvIlbcFrameMode  
This Texatual Convention represents the iLBC codec frame modes. The possible values are : frameMode20: This mode operates at 15.2 kbps and each frame is packetized in 38 bytes. frameMode30: This mode operates at 13.33 kbps and each frame is packetized in 50 bytes.
TEXTUAL-CONVENTION    
  INTEGER frameMode20(20), frameMode30(30)  

CvCallConnectionType  
Call connection represents the connection/association/session between two media call end points. Following are the different connection types. h323 - h323 protocol. sip - Session Initiation Protocol. mgcp - Media Gateway Control Protocol. sccp - Cisco proprietary Skinny Call Control Protocol. multicast - multicast call connections. cacontrol - Call Agent Control. telephony - telephony signal call connections.
TEXTUAL-CONVENTION    
  INTEGER h323(1), sip(2), mgcp(3), sccp(4), multicast(5), cacontrol(6), telephony(7)  

CvPeerCfgEntry  
SEQUENCE    
  cvPeerCfgIndex Integer32
  cvPeerCfgIfIndex InterfaceIndexOrZero
  cvPeerCfgType INTEGER
  cvPeerCfgRowStatus RowStatus
  cvPeerCfgPeerType INTEGER

CvVoicePeerCfgEntry  
SEQUENCE    
  cvVoicePeerCfgSessionTarget DisplayString
  cvVoicePeerCfgDialDigitsPrefix DisplayString
  cvVoicePeerCfgDIDCallEnable TruthValue
  cvVoicePeerCfgCasGroup CvCasGroup
  cvVoicePeerCfgRegisterE164 TruthValue
  cvVoicePeerCfgForwardDigits Integer32
  cvVoicePeerCfgEchoCancellerTest INTEGER

CvVoIPPeerCfgEntry  
SEQUENCE    
  cvVoIPPeerCfgSessionProtocol CvSessionProtocol
  cvVoIPPeerCfgDesiredQoS QosService
  cvVoIPPeerCfgMinAcceptableQoS QosService
  cvVoIPPeerCfgSessionTarget DisplayString
  cvVoIPPeerCfgCoderRate CvcSpeechCoderRate
  cvVoIPPeerCfgFaxRate CvcFaxTransmitRate
  cvVoIPPeerCfgVADEnable TruthValue
  cvVoIPPeerCfgExpectFactor Integer32
  cvVoIPPeerCfgIcpif Integer32
  cvVoIPPeerCfgPoorQoVNotificationEnable TruthValue
  cvVoIPPeerCfgUDPChecksumEnable TruthValue
  cvVoIPPeerCfgIPPrecedence Integer32
  cvVoIPPeerCfgTechPrefix DisplayString
  cvVoIPPeerCfgDigitRelay BITS
  cvVoIPPeerCfgCoderBytes Integer32
  cvVoIPPeerCfgFaxBytes Integer32
  cvVoIPPeerCfgInBandSignaling CvcInBandSignaling
  cvVoIPPeerCfgMediaSetting INTEGER
  cvVoIPPeerCfgDesiredQoSVideo QosService
  cvVoIPPeerCfgMinAcceptableQoSVideo QosService
  cvVoIPPeerCfgRedirectip2ip TruthValue
  cvVoIPPeerCfgOctetAligned TruthValue
  cvVoIPPeerCfgBitRates CvAmrNbBitRateMode
  cvVoIPPeerCfgCRC TruthValue
  cvVoIPPeerCfgCoderMode CvIlbcFrameMode
  cvVoIPPeerCfgCodingMode INTEGER
  cvVoIPPeerCfgBitRate Unsigned32
  cvVoIPPeerCfgFrameSize INTEGER
  cvVoIPPeerCfgDSCPPolicyNotificationEnable TruthValue
  cvVoIPPeerCfgMediaPolicyNotificationEnable TruthValue

CvPeerCommonCfgEntry  
SEQUENCE    
  cvPeerCommonCfgIncomingDnisDigits DisplayString
  cvPeerCommonCfgMaxConnections Integer32
  cvPeerCommonCfgApplicationName DisplayString
  cvPeerCommonCfgPreference Integer32
  cvPeerCommonCfgHuntStop TruthValue
  cvPeerCommonCfgDnisMappingName DnisMapname
  cvPeerCommonCfgSourceCarrierId SnmpAdminString
  cvPeerCommonCfgTargetCarrierId SnmpAdminString
  cvPeerCommonCfgSourceTrunkGrpLabel SnmpAdminString
  cvPeerCommonCfgTargetTrunkGrpLabel SnmpAdminString

CvCallActiveEntry  
SEQUENCE    
  cvCallActiveConnectionId CvcGUid
  cvCallActiveTxDuration AbsoluteCounter32
  cvCallActiveVoiceTxDuration AbsoluteCounter32
  cvCallActiveFaxTxDuration AbsoluteCounter32
  cvCallActiveCoderTypeRate CvcCoderTypeRate
  cvCallActiveNoiseLevel Integer32
  cvCallActiveACOMLevel Integer32
  cvCallActiveOutSignalLevel Integer32
  cvCallActiveInSignalLevel Integer32
  cvCallActiveERLLevel Integer32
  cvCallActiveSessionTarget DisplayString
  cvCallActiveImgPageCount AbsoluteCounter32
  cvCallActiveCallingName SnmpAdminString
  cvCallActiveCallerIDBlock TruthValue
  cvCallActiveEcanReflectorLocation Integer32
  cvCallActiveAccountCode SnmpAdminString
  cvCallActiveERLLevelRev1 Integer32
  cvCallActiveCallId Unsigned32

CvVoIPCallActiveEntry  
SEQUENCE    
  cvVoIPCallActiveConnectionId CvcGUid
  cvVoIPCallActiveRemoteIPAddress IpAddress
  cvVoIPCallActiveRemoteUDPPort Integer32
  cvVoIPCallActiveRoundTripDelay Gauge32
  cvVoIPCallActiveSelectedQoS QosService
  cvVoIPCallActiveSessionProtocol CvSessionProtocol
  cvVoIPCallActiveSessionTarget DisplayString
  cvVoIPCallActiveOnTimeRvPlayout AbsoluteCounter32
  cvVoIPCallActiveGapFillWithSilence AbsoluteCounter32
  cvVoIPCallActiveGapFillWithPrediction AbsoluteCounter32
  cvVoIPCallActiveGapFillWithInterpolation AbsoluteCounter32
  cvVoIPCallActiveGapFillWithRedundancy AbsoluteCounter32
  cvVoIPCallActiveHiWaterPlayoutDelay AbsoluteCounter32
  cvVoIPCallActiveLoWaterPlayoutDelay Gauge32
  cvVoIPCallActiveReceiveDelay Gauge32
  cvVoIPCallActiveVADEnable TruthValue
  cvVoIPCallActiveCoderTypeRate CvcCoderTypeRate
  cvVoIPCallActiveLostPackets AbsoluteCounter32
  cvVoIPCallActiveEarlyPackets AbsoluteCounter32
  cvVoIPCallActiveLatePackets AbsoluteCounter32
  cvVoIPCallActiveUsername SnmpAdminString
  cvVoIPCallActiveProtocolCallId OCTET STRING
  cvVoIPCallActiveRemSigIPAddrT InetAddressType
  cvVoIPCallActiveRemSigIPAddr InetAddress
  cvVoIPCallActiveRemSigPort Integer32
  cvVoIPCallActiveRemMediaIPAddrT InetAddressType
  cvVoIPCallActiveRemMediaIPAddr InetAddress
  cvVoIPCallActiveRemMediaPort Integer32
  cvVoIPCallActiveSRTPEnable TruthValue
  cvVoIPCallActiveOctetAligned TruthValue
  cvVoIPCallActiveBitRates CvAmrNbBitRateMode
  cvVoIPCallActiveModeChgPeriod Integer32
  cvVoIPCallActiveModeChgNeighbor TruthValue
  cvVoIPCallActiveMaxPtime Integer32
  cvVoIPCallActiveCRC TruthValue
  cvVoIPCallActiveRobustSorting TruthValue
  cvVoIPCallActiveEncap CvAmrNbRtpEncap
  cvVoIPCallActiveInterleaving Integer32
  cvVoIPCallActivePtime Integer32
  cvVoIPCallActiveChannels Integer32
  cvVoIPCallActiveCoderMode CvIlbcFrameMode
  cvVoIPCallActiveCallId Unsigned32
  cvVoIPCallActiveCallReferenceId CvcCallReferenceIdOrZero
  ccVoIPCallActivePolicyName DisplayString
  cvVoIPCallActiveReversedDirectionPeerAddress DisplayString
  cvVoIPCallActiveSessionId Unsigned32

CvCallVolConnEntry  
SEQUENCE    
  cvCallVolConnIndex CvCallConnectionType
  cvCallVolConnActiveConnection Gauge32

CvCallVolPeerEntry  
SEQUENCE    
  cvCallVolPeerIncomingCalls Gauge32
  cvCallVolPeerOutgoingCalls Gauge32

CvCallVolIfEntry  
SEQUENCE    
  cvCallVolMediaIncomingCalls Gauge32
  cvCallVolMediaOutgoingCalls Gauge32

CvCallHistoryEntry  
SEQUENCE    
  cvCallHistoryConnectionId CvcGUid
  cvCallHistoryTxDuration AbsoluteCounter32
  cvCallHistoryVoiceTxDuration AbsoluteCounter32
  cvCallHistoryFaxTxDuration AbsoluteCounter32
  cvCallHistoryCoderTypeRate CvcCoderTypeRate
  cvCallHistoryNoiseLevel Integer32
  cvCallHistoryACOMLevel Integer32
  cvCallHistorySessionTarget DisplayString
  cvCallHistoryImgPageCount AbsoluteCounter32
  cvCallHistoryCallingName SnmpAdminString
  cvCallHistoryCallerIDBlock TruthValue
  cvCallHistoryAccountCode SnmpAdminString
  cvCallHistoryCallId Unsigned32

CvVoIPCallHistoryEntry  
SEQUENCE    
  cvVoIPCallHistoryConnectionId CvcGUid
  cvVoIPCallHistoryRemoteIPAddress IpAddress
  cvVoIPCallHistoryRemoteUDPPort Integer32
  cvVoIPCallHistoryRoundTripDelay Gauge32
  cvVoIPCallHistorySelectedQoS QosService
  cvVoIPCallHistorySessionProtocol CvSessionProtocol
  cvVoIPCallHistorySessionTarget DisplayString
  cvVoIPCallHistoryOnTimeRvPlayout AbsoluteCounter32
  cvVoIPCallHistoryGapFillWithSilence AbsoluteCounter32
  cvVoIPCallHistoryGapFillWithPrediction AbsoluteCounter32
  cvVoIPCallHistoryGapFillWithInterpolation AbsoluteCounter32
  cvVoIPCallHistoryGapFillWithRedundancy AbsoluteCounter32
  cvVoIPCallHistoryHiWaterPlayoutDelay AbsoluteCounter32
  cvVoIPCallHistoryLoWaterPlayoutDelay Gauge32
  cvVoIPCallHistoryReceiveDelay Gauge32
  cvVoIPCallHistoryVADEnable TruthValue
  cvVoIPCallHistoryCoderTypeRate CvcCoderTypeRate
  cvVoIPCallHistoryIcpif Integer32
  cvVoIPCallHistoryLostPackets AbsoluteCounter32
  cvVoIPCallHistoryEarlyPackets AbsoluteCounter32
  cvVoIPCallHistoryLatePackets AbsoluteCounter32
  cvVoIPCallHistoryUsername SnmpAdminString
  cvVoIPCallHistoryProtocolCallId OCTET STRING
  cvVoIPCallHistoryRemSigIPAddrT InetAddressType
  cvVoIPCallHistoryRemSigIPAddr InetAddress
  cvVoIPCallHistoryRemSigPort Integer32
  cvVoIPCallHistoryRemMediaIPAddrT InetAddressType
  cvVoIPCallHistoryRemMediaIPAddr InetAddress
  cvVoIPCallHistoryRemMediaPort Integer32
  cvVoIPCallHistorySRTPEnable TruthValue
  cvVoIPCallHistoryFallbackIcpif Integer32
  cvVoIPCallHistoryFallbackLoss AbsoluteCounter32
  cvVoIPCallHistoryFallbackDelay Gauge32
  cvVoIPCallHistoryOctetAligned TruthValue
  cvVoIPCallHistoryBitRates CvAmrNbBitRateMode
  cvVoIPCallHistoryModeChgPeriod Integer32
  cvVoIPCallHistoryModeChgNeighbor TruthValue
  cvVoIPCallHistoryMaxPtime Integer32
  cvVoIPCallHistoryCRC TruthValue
  cvVoIPCallHistoryRobustSorting TruthValue
  cvVoIPCallHistoryEncap CvAmrNbRtpEncap
  cvVoIPCallHistoryInterleaving Integer32
  cvVoIPCallHistoryPtime Integer32
  cvVoIPCallHistoryChannels Integer32
  cvVoIPCallHistoryCoderMode CvIlbcFrameMode
  cvVoIPCallHistoryCallId Unsigned32
  cvVoIPCallHistoryCallReferenceId CvcCallReferenceIdOrZero
  cvVoIPCallHistorySessionId Unsigned32

CvCallRateStatsEntry  
SEQUENCE    
  cvCallRateStatsIntvlDurUnits CvCallVolumeStatsIntvlType
  cvCallRateStatsIntvlDur Unsigned32
  cvCallRateStatsMaxVal Unsigned32
  cvCallRateStatsAvgVal Unsigned32

CvCallLegRateStatsEntry  
SEQUENCE    
  cvCallLegRateStatsIntvlDurUnits CvCallVolumeStatsIntvlType
  cvCallLegRateStatsIntvlDur Unsigned32
  cvCallLegRateStatsMaxVal Unsigned32
  cvCallLegRateStatsAvgVal Unsigned32

CvActiveCallStatsEntry  
SEQUENCE    
  cvActiveCallStatsIntvlDurUnits CvCallVolumeStatsIntvlType
  cvActiveCallStatsIntvlDur Unsigned32
  cvActiveCallStatsMaxVal Unsigned32
  cvActiveCallStatsAvgVal Unsigned32

CvCallDurationStatsEntry  
SEQUENCE    
  cvCallDurationStatsIntvlDurUnits CvCallVolumeStatsIntvlType
  cvCallDurationStatsIntvlDur Unsigned32
  cvCallDurationStatsMaxVal Unsigned32
  cvCallDurationStatsAvgVal Unsigned32

CvSipMsgRateStatsEntry  
SEQUENCE    
  cvSipMsgRateStatsIntvlDurUnits CvCallVolumeStatsIntvlType
  cvSipMsgRateStatsIntvlDur Unsigned32
  cvSipMsgRateStatsMaxVal Unsigned32
  cvSipMsgRateStatsAvgVal Unsigned32

CvCallRateWMEntry  
SEQUENCE    
  cvCallRateWMIntvlDurUnits CvCallVolumeWMIntvlType
  cvCallRateWMIndex Unsigned32
  cvCallRateWMValue Unsigned32
  cvCallRateWMts DateAndTime

CvCallLegRateWMEntry  
SEQUENCE    
  cvCallLegRateWMIntvlDurUnits CvCallVolumeWMIntvlType
  cvCallLegRateWMIndex Unsigned32
  cvCallLegRateWMValue Unsigned32
  cvCallLegRateWMts DateAndTime

CvActiveCallWMEntry  
SEQUENCE    
  cvActiveCallWMIntvlDurUnits CvCallVolumeWMIntvlType
  cvActiveCallWMIndex Unsigned32
  cvActiveCallWMValue Unsigned32
  cvActiveCallWMts DateAndTime

CvSipMsgRateWMEntry  
SEQUENCE    
  cvSipMsgRateWMIntvlDurUnits CvCallVolumeWMIntvlType
  cvSipMsgRateWMIndex Unsigned32
  cvSipMsgRateWMValue Unsigned32
  cvSipMsgRateWMts DateAndTime

Defined Values

ciscoVoiceDialControlMIB 2.9.63
This MIB module enhances the IETF Dial Control MIB (RFC2128) by providing management of voice telephony peers on both a circuit-switched telephony network, and an IP data network. *** ABBREVIATIONS, ACRONYMS AND SYMBOLS *** GSM - Global System for Mobile Communication AMR-NB - Adaptive Multi Rate - Narrow Band iLBC - internet Low Bitrate Codec KPML - Key Press Markup Language MGCP - Media Gateway Control Protocol. SIP - Session Initiation Protocol. H323 - One of the voip signalling protocol. SCCP - Skinny Client Control Protocol. dialpeer - This represents a configured interface that carries the dial map. A dialpeer maps the called and calling numbers with the port or IP interface to be used. License call capacity - This represents the licensed maximum call capacity of the gateway. iSAC - Internet Speech Audio Codec RPH - Resource Priority Header DSCP - Diffserv Code Points
MODULE-IDENTITY    

cvdcMIBObjects 2.9.63.1
OBJECT IDENTIFIER    

cvGeneralConfiguration 2.9.63.1.1
OBJECT IDENTIFIER    

cvPeer 2.9.63.1.2
OBJECT IDENTIFIER    

cvGatewayCallActive 2.9.63.1.3
OBJECT IDENTIFIER    

cvGatewayCallHistory 2.9.63.1.4
OBJECT IDENTIFIER    

cvGeneralPoorQoVNotificationEnable 2.9.63.1.1.1
This object indicates whether cvdcPoorQoVNotification (or the newer cvdcPoorQoVNotificationRev1) traps should be generated for a poor quality of voice calls. If the value of this object is 'true', cvdcPoorQoVNotification (or the newer cvdcPoorQoVNotificationRev1) traps will be generated for all voice over IP peers when a poor quality of voice call condition is detected after the voice gateway call disconnection. If the value of this object is 'false', cvdcPoorQoVNotification (or the newer cvdcPoorQoVNotificationRev1) traps will be generated only for calls for which the cvVoIPPeerCfgPoorQoVNotificationEnable object of voice over IP peers having set to 'true'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvGeneralFallbackNotificationEnable 2.9.63.1.1.2
This object indicates whether cvdcFallbackNotification traps should be generated for fallback. If the value of this object is 'true', cvdcFallbackNotification traps will be generated for all voice over IP peers.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvGeneralDSCPPolicyNotificationEnable 2.9.63.1.1.3
This object indicates whether cvdcPolicyViolationNotification traps should be generated for a RPH to DSCP mapping violation for SIP voice calls. If the value of this object is 'true', cvdcPolicyViolationNotification traps will be generated for SIP voice over IP peers when a RPH to DSCP violation condition is detected . If the value of this object is 'false', cvdcPolicyViolationNotification traps will be generated only for calls for which the cvVoIPPeerCfgDSCPPolicyNotificationEnable object of voice over IP peers having set to 'true'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvGeneralMediaPolicyNotificationEnable 2.9.63.1.1.4
This object indicates whether cvdcPolicyViolationNotification traps should be generated for Media violation for SIP voice calls. If the value of this object is 'true', cvdcPolicyViolationNotification traps will be generated for SIP voice over IP peers when media violation condition is detected . If the value of this object is 'false', cvdcPolicyViolationNotification traps will be generated only for calls for which the cvVoIPPeerCfgMediaPolicyNotificationEnable object of voice over IP peers having set to 'true'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvPeerCfgTable 2.9.63.1.2.1
The table contains the Voice Generic Peer information that is used to create an ifIndexed row with an appropriate ifType that is associated with the cvPeerCfgType and cvPeerCfgPeerType objects.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvPeerCfgEntry

cvPeerCfgEntry 2.9.63.1.2.1.1
A single voice generic Peer. The creation of this entry will create an associated ifEntry with an ifType that is associated with cvPeerCfgType, i.e., for 'voiceEncap' encapsulation, an ifEntry will contain an ifType voiceEncap(103); for 'voiceOverIp' encapsulation, an ifEntry will contain an ifType voiceOverIp(104). The ifAdminStatus of the newly created ifEntry is set to 'up' and ifOperStatus is set to 'down'. In addition, an associated voiceEncap/voiceOverIp Peer configuration entry is created after the successful ifEntry creation. Then ifIndex of the newly created ifEntry must be used by the network manager to create a peer configuration entry of IETF Dial Control MIB (Refer to RFC 2128 section 2.2.3.1 and the description of dialCtlPeerCfgEntry for the detailed information). In summary, the voice dial peer creation steps are as follows: [1] create this entry (voice/data generic peer entry). [2] read the cvPeerCfgIfIndex of this entry for the ifIndex of newly created voice/data generic peer. [3] create the dialCtlPeerCfgEntry of RFC 2128 with the indices of dialCtlPeerCfgId and the ifIndex of newly created voice generic peer. For each VoIP peer, it uses IP address and UDP port with RTP protocol to transfer voice packet. Therefore, it does not have its lower layer interface. The dialCtlPeerCfgIfType object of IETF Dial Control MIB must set to 'other' and the dialCtlPeerCfgLowerIf must set to '0'. After the successful creation of peer configuration entry of IETF Dial Control MIB, the dial plan software in managed device will set the ifOperStatus of the newly created voiceEncap/voiceOverIp ifEntry to 'up' for enabling the peer function if the peer configuration is completed. When this entry is deleted, its associated ifEntry, voiceEncap/voiceOverIp specific peer entry and the peer entry of IETF Dial Control MIB are deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  CvPeerCfgEntry  

cvPeerCfgIndex 2.9.63.1.2.1.1.1
An arbitrary index that uniquely identifies a generic voice peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

cvPeerCfgIfIndex 2.9.63.1.2.1.1.2
The ifIndex of the peer associated ifEntry. The ifIndex appears after the associated ifEntry is created successfully. This ifIndex will be used to access the objects in the Voice over Telephony or Voice over IP peer specific table. In addition, the ifIndex is also used to access the associated peer configuration entry of the IETF Dial Control MIB. If the peer associated ifEntry had not been created, then this object has a value of zero.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

cvPeerCfgType 2.9.63.1.2.1.1.3
Specifies the type of voice related encapsulation. voice - voice encapsulation (voiceEncap ifType) on the telephony network. voip - VoIP encapsulation (voiceOverIp ifType) on the IP network. mmail - Media Mail over IP encapsulation (mediaMailOverIp ifType) on the IP network. voatm - VoATM encapsulation (voiceOverATM ifType) on the ATM network. vofr - VoFR encapsulation (voiceOverFR ifType) on the Frame Relay network.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER voice(1), voip(2), mmail(3), voatm(4), vofr(5)  

cvPeerCfgRowStatus 2.9.63.1.2.1.1.4
This object is used to create a new row or modify or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cvPeerCfgPeerType 2.9.63.1.2.1.1.5
Specifies the type of a peer. voice - peer in voice type to be defined in a voice gateway for voice calls. data - peer in data type to be defined in gateway that supports universal ports for modem/data calls and integrated ports for data calls.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER voice(1), data(2)  

cvVoicePeerCfgTable 2.9.63.1.2.2
The table contains the Voice over Telephony peer specific information that is required to accept voice calls or to which it will place them or perform various loopback tests via interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvVoicePeerCfgEntry

cvVoicePeerCfgEntry 2.9.63.1.2.2.1
A single Voice specific Peer. One entry per voice encapsulation. The entry is created when its associated 'voiceEncap(103)' encapsulation ifEntry is created. This entry is deleted when its associated ifEntry is deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  CvVoicePeerCfgEntry  

cvVoicePeerCfgSessionTarget 2.9.63.1.2.2.1.1
The object specifies the session target of the peer. Session Targets definitions: The session target has the syntax used by the IETF service location protocol. The syntax is as follows: mapping-type:type-specific-syntax the mapping-type specifies a scheme for mapping the matching dial string to a session target. The valid Mapping type definitions for the peer are as follows: loopback - Syntax: loopback:where 'where' string is defined as follows: compressed - loopback is performed on compressed voice as close to the CODEC which processes the data as possible. uncompressed - loopback is performed on the PCM or analog voice as close to the telephony endpoint as possible. Local loopback case: uncompressed - the PCM voice coming into the DSP is simply turned around and sent back out, allowing testing of the transmit--> receive paths in the telephony endpoint. compressed - the compressed voice coming out of the CODEC is turned around on the DSP module and fed back into the decompressor through the jitter buffer. In addition to the telephony endpoint, this tests both the encode and decode paths without involving data paths or packet handling on the host router. Remote loopback case: compressed - RTP packets received from the network are decapsulated and passed to the DSP board. Instead of feeding these into the CODEC for decompression, they are immediately sent back to the session application as if they had originated locally and been compressed. uncompressed - In addition to the above, the voice samples are sent all the way through the CODEC and then turned around instead of being sent to the telephony endpoint
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

cvVoicePeerCfgDialDigitsPrefix 2.9.63.1.2.2.1.2
The object specifies the prefix of the dial digits for the peer. The dial digits prefix is sent to telephony interface before the real phone number when the system places the outgoing call to the voice encapsulation peer over telephony interface.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

cvVoicePeerCfgDIDCallEnable 2.9.63.1.2.2.1.3
The object enables/disables the DID call treatment for incoming DNIS digits. true - treat the incoming DNIS digits as if the digits are received from DID trunk. false - Disable DID call treatment for incoming DNIS digits.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvVoicePeerCfgCasGroup 2.9.63.1.2.2.1.4
The object specifies the CAS group number of a CAS capable T1/E1 that is in the dialCtlPeerCfgLowerIf object of RFC2128. This object can be set to a valid CAS group number only if the dialCtlPeerCfgLowerIf contains a valid ifIndex for a CAS capable T1/E1. The object must set to -1 before the value of the dialCtlPeerCfgLowerIf object of RFC2128 can be changed.
Status: current Access: read-write
OBJECT-TYPE    
  CvCasGroup  

cvVoicePeerCfgRegisterE164 2.9.63.1.2.2.1.5
This object specifies that the E.164 number specified in the dialCtlPeerCfgOriginateAddress field of the associated dialCtlPeerCfgTable entry be registered as an extension phone number of this gateway for H323 gatekeeper and/or SIP registrar.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvVoicePeerCfgForwardDigits 2.9.63.1.2.2.1.6
This object specifies the number of dialed digits to forward to the remote destination in the setup message. The object can take the value: 0-32 number of right justified digits to forward -1 default -2 forward extra digits i.e those over and above those needed to match to the destination pattern -3 forward all digits
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -3..32  

cvVoicePeerCfgEchoCancellerTest 2.9.63.1.2.2.1.7
This object specifies which, if any, test to run in the echo canceller when a call from the network is connected. echoCancellerTestNone - do not run a test. echoCancellerG168Test2A - run ITU-T G.168 Test 2A. echoCancellerG168Test2B - run ITU-T G.168 Test 2B. echoCancellerG168Test2Ca - run ITU-T G.168 Test 2C(a). echoCancellerG168Test2Cb - run ITU-T G.168 Test 2C(b). echoCancellerG168Test3A - run ITU-T G.168 Test 3A. echoCancellerG168Test3B - run ITU-T G.168 Test 3B. echoCancellerG168Test3C - run ITU-T G.168 Test 3C. echoCancellerG168Test4 - run ITU-T G.168 Test 4. echoCancellerG168Test5 - run ITU-T G.168 Test 5. echoCancellerG168Test6 - run ITU-T G.168 Test 6. echoCancellerG168Test7 - run ITU-T G.168 Test 7. echoCancellerG168Test9 - run ITU-T G.168 Test 9.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER echoCancellerTestNone(1), echoCancellerG168Test2A(2), echoCancellerG168Test2B(3), echoCancellerG168Test2Ca(4), echoCancellerG168Test2Cb(5), echoCancellerG168Test3A(6), echoCancellerG168Test3B(7), echoCancellerG168Test3C(8), echoCancellerG168Test4(9), echoCancellerG168Test6(10), echoCancellerG168Test9(11), echoCancellerG168Test5(12), echoCancellerG168Test7(13)  

cvVoIPPeerCfgTable 2.9.63.1.2.3
The table contains the Voice over IP (VoIP) peer specific information that is required to accept voice calls or to which it will place them via IP backbone with the specified session protocol in cvVoIPPeerCfgSessionProtocol.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvVoIPPeerCfgEntry

cvVoIPPeerCfgEntry 2.9.63.1.2.3.1
A single VoIP specific Peer. One entry per VoIP encapsulation. The entry is created when its associated 'voiceOverIp(104)' encapsulation ifEntry is created. This entry is deleted when its associated ifEntry is deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  CvVoIPPeerCfgEntry  

cvVoIPPeerCfgSessionProtocol 2.9.63.1.2.3.1.1
The object specifies the session protocol to be used for Internet call between local and remote router via IP backbone.
Status: current Access: read-write
OBJECT-TYPE    
  CvSessionProtocol  

cvVoIPPeerCfgDesiredQoS 2.9.63.1.2.3.1.2
The object specifies the user requested Quality of Service for the call.
Status: current Access: read-write
OBJECT-TYPE    
  QosService  

cvVoIPPeerCfgMinAcceptableQoS 2.9.63.1.2.3.1.3
The object specifies the minimally acceptable Quality of Service for the call.
Status: current Access: read-write
OBJECT-TYPE    
  QosService  

cvVoIPPeerCfgSessionTarget 2.9.63.1.2.3.1.4
The object specifies the session target of the peer. Session Targets definitions: The session target has the syntax used by the IETF service location protocol. The syntax is as follows: mapping-type:type-specific-syntax the mapping-type specifies a scheme for mapping the matching dial string to a session target. The type-specific-syntax is exactly that, something that the particular mapping scheme can understand. For example, Session target Meaning ipv4:171.68.13.55:1006 The session target is the IP version 4 address of 171.68.13.55 and port 1006. dns:pots.cisco.com:1661 The session target is the IP host with dns name pots.cisco.com, and port 1661. ras The session target is the gatekeeper with RAS (Registration , Admission, Status protocol). settlement The session target is the settlement server. enum:1 The session target is the enum profile match table 1. The valid Mapping type definitions for the peer are as follows: ipv4 - Syntax: ipv4:w.x.y.z:port or ipv4:w.x.y.z dns - Syntax: dns:host.domain:port or dns:host.domain ras - Syntax: ras settlement - Syntax: settlement enum - Syntax: enum: loopback - Syntax: loopback:where 'where' string is defined as follows: rtp - loopback is performed at the transport protocol level. Local loopback case: rtp - the session application sets up an RTP stream to itself (i.e. actually allocates a port pair and opens the appropriate UDP sockets). It then does the full RTP encapsulation, sends the packets to the loopback IP address, receives the RTP packets, and hands the compressed voice back to the CODEC. This tests the entire local processing path, both transmit and receive, in the router, as well as all of the above paths. Remote loopback case: rtp: RTP packets received from the network are decapsulated and immediately re-encapsulated in the outbound RTP stream, using the same media clock (i.e. timestamp) as the received packet. They are then sent back to the remote source router as if the voice had originated on a telephony port on the local router.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

cvVoIPPeerCfgCoderRate 2.9.63.1.2.3.1.5
This object specifies the most desirable codec of speech for the VoIP peer.
Status: current Access: read-write
OBJECT-TYPE    
  CvcSpeechCoderRate  

cvVoIPPeerCfgFaxRate 2.9.63.1.2.3.1.6
This object specifies the default transmit rate of FAX the VoIP peer. If the value of this object is 'none', then the Fax relay feature is disabled; otherwise the Fax relay feature is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  CvcFaxTransmitRate  

cvVoIPPeerCfgVADEnable 2.9.63.1.2.3.1.7
This object specifies whether or not the VAD (Voice Activity Detection) voice data is continuously transmitted to IP backbone.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvVoIPPeerCfgExpectFactor 2.9.63.1.2.3.1.8
This object specifies the user requested Expectation Factor of voice quality for the call via this peer.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..20  

cvVoIPPeerCfgIcpif 2.9.63.1.2.3.1.9
This object specifies the user requested Calculated Planning Impairment Factor (Icpif) for the call via this peer.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..55  

cvVoIPPeerCfgPoorQoVNotificationEnable 2.9.63.1.2.3.1.10
This object specifies whether cvdcPoorQoVNotification (or the newer cvdcPoorQoVNotificationRev1) traps should be generated for the call that is associated with this peer.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvVoIPPeerCfgUDPChecksumEnable 2.9.63.1.2.3.1.11
This object specifies whether the outgoing voice related UDP packet contains a valid checksum value. true - enable the checksum of outgoing voice UDP packets false - disable the checksum of outgoing voice UDP packets
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvVoIPPeerCfgIPPrecedence 2.9.63.1.2.3.1.12
This object specifies the value to be stored in the IP Precedence field of voice packets, with values ranging from 0 (normal precedence) through 7 (network control), allowing the managed system to set the importance of each voice packet for delivering them to the destination peer.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cvVoIPPeerCfgTechPrefix 2.9.63.1.2.3.1.13
This object specifies the technology prefix of the peer, The technology prefix and the called party address are passed in Admission Request (ARQ) to gatekeeper for the called party address resolution during call setup.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

cvVoIPPeerCfgDigitRelay 2.9.63.1.2.3.1.14
This object specifies the methods to transmit dial digits (DTMF or MF digits) via IP network. rtpCisco - Enable capability to transmit dial digits with Cisco proprietary RTP payload type. h245Signal - Enable capability to transmit dtmf digits across the H.245 channel, via the signal field of the UserInputIndication message h245Alphanumeric - Enable capability to transmit dtmf digit across the H.245 channel, via the string or alphanumeric fields of the UserInputIndication message rtpNte - Enable capability to transmit dial digits using Named Telephony Event per RFC 2833 section 3. sipNotify - Enable capability to transmit dtmf digits using unsolicited SIP NOTIFY messages. This mechanism is only available for SIP dialpeers. sipKpml - Enable capability to transmit dtmf digits using KPML over SIP SUBSCRIBE and NOTIFY messages. This mechanism is only available for SIP dialpeers. Modifying the value of cvVoIPPeerCfgSessionProtocol can reset the digit-relay method associated bits value in this object if the modified session protocol does not support these digit-relay methods.
Status: current Access: read-write
OBJECT-TYPE    
  BITS rtpCisco(0), h245Signal(1), h245Alphanumeric(2), rtpNte(3), sipNotify(4), sipKpml(5)  

cvVoIPPeerCfgCoderBytes 2.9.63.1.2.3.1.15
This object specifies the size of the voice payload sample to be produced by the coder specified in cvVoIPPeerCfgCoderRate. Each coder sample produces 10 bytes of voice payload. The specified value will be rounded down to the nearest valid size. A value of 0, specifies that the coder defined by cvVoIPPeerCfgCoderRate should produce its default payload size.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 10..240  

cvVoIPPeerCfgFaxBytes 2.9.63.1.2.3.1.16
This object specifies the payload size to be produced by the coder when it is generating fax data. A value of 0, specifies that the coder specified in cvVoIPCfgPeerCoderRate should produce its default fax payload size.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 10..255  

cvVoIPPeerCfgInBandSignaling 2.9.63.1.2.3.1.17
This object specifies the type of in-band signaling that will be used between the end points of the call. It is used by the router to determine how to interpret ABCD signaling bits sent as part of voice payload data.
Status: current Access: read-write
OBJECT-TYPE    
  CvcInBandSignaling  

cvVoIPPeerCfgMediaSetting 2.9.63.1.2.3.1.23
This object specifies how the media is to be setup on an IP-IP Gateway. Two choices are valid: flow-through and flow-around. When in flow-through mode, which is the default setting, the IP-IP Gateway will terminate and then re-originate the media stream. When flow-around is configured the Gateway will not be involved with the media, since it will flow-around the Gateway and will be established directly between the endpoints.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER flowThrough(1), flowAround(2)  

cvVoIPPeerCfgDesiredQoSVideo 2.9.63.1.2.3.1.24
The object specifies the user requested Quality of Service for the video portion of the call.
Status: current Access: read-write
OBJECT-TYPE    
  QosService  

cvVoIPPeerCfgMinAcceptableQoSVideo 2.9.63.1.2.3.1.25
The object specifies the minimally acceptable Quality of Service for the video portion of the call.
Status: current Access: read-write
OBJECT-TYPE    
  QosService  

cvVoIPPeerCfgRedirectip2ip 2.9.63.1.2.3.1.26
This object specifies the Inbound VoIP calls that match an outbound VoIP dialpeer will be responded with a SIP redirect(for inbound SIP) or H.450.3 call-forward(for inbound H.323).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvVoIPPeerCfgOctetAligned 2.9.63.1.2.3.1.27
If the object has a value true(1) octet align operation is used, and if the value is false(2), bandwidth efficient operation is used. This object is not instantiated when the object cvVoIPPeerCfgCoderRate is not equal to gsmAmrNb enum.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvVoIPPeerCfgBitRates 2.9.63.1.2.3.1.28
This object indicates modes of Bit rates. One or more upto four modes can be configured at the same time as bit rates can be changed dynamically for AMR-NB codec. This object is not instantiated when the object cvVoIPPeerCfgCoderRate is not equal to gsmAmrNb enum.
Status: current Access: read-write
OBJECT-TYPE    
  CvAmrNbBitRateMode  

cvVoIPPeerCfgCRC 2.9.63.1.2.3.1.29
If the object has a value of true(1), frame CRC will be included in the payload and if the value is false(2), frame CRC will not be included in the payload. This object is applicable only when RTP frame type is octet aligned. This object is not instantiated when the object cvVoIPPeerCfgCoderRate is not equal to gsmAmrNb enum.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvVoIPPeerCfgCoderMode 2.9.63.1.2.3.1.30
This object indicates the iLBC codec mode to be used. The value of this object is valid only if cvVoIPPeerCfgCoderRate is equal to 'iLBC'.
Status: current Access: read-write
OBJECT-TYPE    
  CvIlbcFrameMode  

cvVoIPPeerCfgCodingMode 2.9.63.1.2.3.1.31
This object specifies the coding mode to be used. The object is instantiated only if cvVoIPPeerCfgCoderRate is 'iSAC'. Following coding modes are supported: adaptive (1) - adaptive mode where iSAC performs bandwidth estimation and adapts to the available channel bandwidth. independent (2) - independent mode in which no bandwidth estimation is performed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER adaptive(1), independent(2)  

cvVoIPPeerCfgBitRate 2.9.63.1.2.3.1.32
This object specifies the target bit rate. The object is instantiated only if cvVoIPPeerCfgCoderRate is 'iSAC'.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 10000..32000  

cvVoIPPeerCfgFrameSize 2.9.63.1.2.3.1.33
This object specifies the frame size used. The object is instantiated only if cvVoIPPeerCfgCoderRate is 'iSAC'. The frame size can be 30 ms or 60 ms, and it can be fixed for all packets or vary depending on the configuration and bandwidth estimation. Thus it can have the following values: frameSize30 - initial frame size of 30 ms frameSize60 - initial frame size of 60 ms frameSize30fixed - fixed frame size 30 ms frameSize60fixed - fixed frame size 60 ms
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER frameSize30(1), frameSize60(2), frameSize30fixed(3), frameSize60fixed(4)  

cvVoIPPeerCfgDSCPPolicyNotificationEnable 2.9.63.1.2.3.1.34
This object specifies whether cvdcPolicyViolationNotification traps should be generated for the call that is associated with this peer for RPH to DSCP mapping and policing feature.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvVoIPPeerCfgMediaPolicyNotificationEnable 2.9.63.1.2.3.1.35
This object specifies whether cvdcPolicyViolationNotification traps should be generated for the call that is associated with this peer for Media policing feature..
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvPeerCommonCfgTable 2.9.63.1.2.4
The table contains the Voice specific peer common configuration information that is required to accept voice calls or to which it will place them or process the incoming calls.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvPeerCommonCfgEntry

cvPeerCommonCfgEntry 2.9.63.1.2.4.1
A single Voice specific Peer. One entry per voice related encapsulation. The entry is created when a voice related encapsulation ifEntry is created. This entry is deleted when its associated ifEntry is deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  CvPeerCommonCfgEntry  

cvPeerCommonCfgIncomingDnisDigits 2.9.63.1.2.4.1.1
The object specifies the prefix of the incoming Dialed Number Identification Service (DNIS) digits for the peer. The DNIS digits prefix is used to match with the incoming DNIS number for incoming call discrimination. If the digits in this object are matched with incoming DNIS number, the associated dialCtlPeerCfgInfoType in RFC 2128 will be used as a call discriminator for differentiating speech, data, fax, video or modem calls.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

cvPeerCommonCfgMaxConnections 2.9.63.1.2.4.1.2
The object specifies the maximum allowed connection to/from the peer. A value of -1 disables the limit of maximum connections.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 1..2147483647  

cvPeerCommonCfgApplicationName 2.9.63.1.2.4.1.3
The object specifies the application to handle the incoming call after the peer is selected. If no application name is specified, then the default session application will take care of the incoming call.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

cvPeerCommonCfgPreference 2.9.63.1.2.4.1.4
This object specifies the selection preference of a peer when multiple peers are matched to the selection criteria. The value of 0 has the lowest preference for peer selection.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10  

cvPeerCommonCfgHuntStop 2.9.63.1.2.4.1.5
This object specifies whether dialpeer hunting should stop when this peer is reached.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvPeerCommonCfgDnisMappingName 2.9.63.1.2.4.1.6
The object specifies a Dialer Number Identification Service (DNIS) map name for the Voice specific peer entry specified in this row. A DNIS is a called party number and they can be grouped and identified by DNIS map.
Status: current Access: read-write
OBJECT-TYPE    
  DnisMapname  

cvPeerCommonCfgSourceCarrierId 2.9.63.1.2.4.1.7
The object specifies the Source Carrier Id for the peer. The Source Carrier Id is used to match with the Source Carrier Id of a call. If the Source Carrier Id in this object is matched with the Source Carrier Id of a call, then the associated peer will be used to handle the call. Only alphanumeric characters, '-' and '_' are allowed in the string.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

cvPeerCommonCfgTargetCarrierId 2.9.63.1.2.4.1.8
The object specifies the Target Carrier Id for the peer. The Target Carrier Id is used to match with the Target Carrier Id of a call. If the Target Carrier Id in this object is matched with the Target Carrier Id of a call, then the associated peer will be used to handle the call. Only alphanumeric characters, '-' and '_' are allowed in the string.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

cvPeerCommonCfgSourceTrunkGrpLabel 2.9.63.1.2.4.1.9
The object specifies the Source Trunk Group Label for the peer. The Source Trunk Group Label is used to match with the Source Trunk Group Label of a call. If the Source Trunk Group Label in this object is matched with the Source Trunk Group Label of a call, then the associated peer will be used to handle the call. Only alphanumeric characters, '-' and '_' are allowed in the string.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

cvPeerCommonCfgTargetTrunkGrpLabel 2.9.63.1.2.4.1.10
The object specifies the Target Trunk Group Label for the peer. The Target Trunk Group Label is used to match with the Target Trunk Group Label of a call. If the Target Trunk Group Label in this object is matched with the Target Trunk Group Label of a call, then the associated peer will be used to handle the call. Only alphanumeric characters, '-' and '_' are allowed in the string.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

cvCallActiveTable 2.9.63.1.3.1
This table is the voice extension to the call active table of IETF Dial Control MIB. It contains voice encapsulation call leg information that is derived from the statistics of lower layer telephony interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvCallActiveEntry

cvCallActiveEntry 2.9.63.1.3.1.1
The information regarding a single voice encapsulation call leg. The call leg entry is identified by using the same index objects that are used by Call Active table of IETF Dial Control MIB to identify the call. An entry of this table is created when its associated call active entry in the IETF Dial Control MIB is created and call active entry contains the call establishment to a voice over telephony network peer. The entry is deleted when its associated call active entry in the IETF Dial Control MIB is deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallActiveEntry  

cvCallActiveConnectionId 2.9.63.1.3.1.1.1
The global connection identifier for the active telephony leg of the call.
Status: current Access: read-only
OBJECT-TYPE    
  CvcGUid  

cvCallActiveTxDuration 2.9.63.1.3.1.1.2
Duration of Transmit path open from this peer to the voice gateway for the call leg. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvCallActiveVoiceTxDuration 2.9.63.1.3.1.1.3
Duration of voice transmitted from this peer to voice gateway for this call leg. The Voice Utilization Rate can be obtained by dividing this by cvCallActiveTXDuration object. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvCallActiveFaxTxDuration 2.9.63.1.3.1.1.4
Duration of fax transmitted from this peer to voice gateway for this call leg. The FAX Utilization Rate can be obtained by dividing this by cvCallActiveTXDuration object. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvCallActiveCoderTypeRate 2.9.63.1.3.1.1.5
The negotiated coder rate. It specifies the transmit rate of voice/fax compression to its associated call leg for the call.
Status: current Access: read-only
OBJECT-TYPE    
  CvcCoderTypeRate  

cvCallActiveNoiseLevel 2.9.63.1.3.1.1.6
The object contains the active noise level for the call leg.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -128..8  

cvCallActiveACOMLevel 2.9.63.1.3.1.1.7
The object contains the sum of Echo Return Loss (ERL), cancellation loss (Echo Return Loss Enhancement) and nonlinear processing loss for the call leg. The value -1 indicates the level can not be determined or level detection is disabled.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..127  

cvCallActiveOutSignalLevel 2.9.63.1.3.1.1.8
The object contains the active output signal level to telephony interface that is used by the call leg.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -128..8  

cvCallActiveInSignalLevel 2.9.63.1.3.1.1.9
The object contains the active input signal level from telephony interface that is used by the call leg.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -128..8  

cvCallActiveERLLevel 2.9.63.1.3.1.1.10
The object contains the current Echo Return Loss (ERL) level for the call leg. The value -1 indicates the level can not be determined or level detection is disabled.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32 -1..45  

cvCallActiveSessionTarget 2.9.63.1.3.1.1.11
The object specifies the session target of the peer that is used for the call leg. This object is set with the information in the call associated cvVoicePeerCfgSessionTarget object when the call is connected.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

cvCallActiveImgPageCount 2.9.63.1.3.1.1.12
The number of FAX related image pages are received or transmitted via the peer for the call leg.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvCallActiveCallingName 2.9.63.1.3.1.1.13
The calling party name of the call. If the name is not available, then it will have a length of zero.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

cvCallActiveCallerIDBlock 2.9.63.1.3.1.1.14
The object indicates whether or not the caller ID feature is blocked for this call.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cvCallActiveEcanReflectorLocation 2.9.63.1.3.1.1.15
The location in milliseconds of the largest amplitude reflector detected by the echo canceller for this call. The value 0 indicates there is no reflector or the information is not available.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..128  

cvCallActiveAccountCode 2.9.63.1.3.1.1.16
The object indicates the account code input to the call. It could be used for call screen or by down stream server for billing purpose. The value of empty string indicates no account code input.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..50)  

cvCallActiveERLLevelRev1 2.9.63.1.3.1.1.17
The object contains the current Echo Return Loss (ERL) level for the call leg. The value -1 indicates the level can not be determined or level detection is disabled.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..200  

cvCallActiveCallId 2.9.63.1.3.1.1.18
This object represents the call identifier for the active telephony leg of the call.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cvVoIPCallActiveTable 2.9.63.1.3.2
This table is the VoIP extension to the call active table of IETF Dial Control MIB. It contains VoIP call leg information about specific VoIP call destination and the selected QoS for the call leg.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvVoIPCallActiveEntry

cvVoIPCallActiveEntry 2.9.63.1.3.2.1
The information regarding a single VoIP call leg. The call leg entry is identified by using the same index objects that are used by Call Active table of IETF Dial Control MIB to identify the call. An entry of this table is created when its associated call active entry in the IETF Dial Control MIB is created and the call active entry contains information for the call establishment to the peer on the IP backbone via a voice over IP peer. The entry is deleted when its associated call active entry in the IETF Dial Control MIB is deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  CvVoIPCallActiveEntry  

cvVoIPCallActiveConnectionId 2.9.63.1.3.2.1.1
The global connection identifier for the active VoIP leg of the call.
Status: current Access: read-only
OBJECT-TYPE    
  CvcGUid  

cvVoIPCallActiveRemoteIPAddress 2.9.63.1.3.2.1.2
Remote system IP address for the VoIP call.
Status: deprecated Access: read-only
OBJECT-TYPE    
  IpAddress  

cvVoIPCallActiveRemoteUDPPort 2.9.63.1.3.2.1.3
Remote system UDP listener port to which to transmit voice packets.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

cvVoIPCallActiveRoundTripDelay 2.9.63.1.3.2.1.4
The voice packet round trip delay between local and the remote system on the IP backbone during the call.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cvVoIPCallActiveSelectedQoS 2.9.63.1.3.2.1.5
The selected RSVP QoS for the voice call.
Status: current Access: read-only
OBJECT-TYPE    
  QosService  

cvVoIPCallActiveSessionProtocol 2.9.63.1.3.2.1.6
The object specifies the session protocol to be used for Internet call between local and remote router via IP backbone.
Status: current Access: read-only
OBJECT-TYPE    
  CvSessionProtocol  

cvVoIPCallActiveSessionTarget 2.9.63.1.3.2.1.7
The object specifies the session target of the peer that is used for the call. This object is set with the information in the call associated cvVoIPPeerCfgSessionTarget object when the voice over IP call is connected.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

cvVoIPCallActiveOnTimeRvPlayout 2.9.63.1.3.2.1.8
Duration of voice playout from data received on time for this call. This plus the durations for the GapFills in the following entries gives the Total Voice Playout Duration for Active Voice. This does not include duration for which no data was sent by the Transmit end as voice signal, e.g., silence suppression and fax signal. The On Time Playout Rate can be computed by dividing this entry by the Total Voice Playout Duration. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallActiveGapFillWithSilence 2.9.63.1.3.2.1.9
Duration of voice signal replaced with signal played out during silence due to voice data not received on time (or lost) from voice gateway this call. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallActiveGapFillWithPrediction 2.9.63.1.3.2.1.10
Duration of voice signal played out with signal synthesized from parameters or samples of data preceding in time due to voice data not received on time (or lost) from voice gateway for this call. An example of such playout is frame-erasure or frame-concealment strategies in G.729 and G.723.1 compression algorithms. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallActiveGapFillWithInterpolation 2.9.63.1.3.2.1.11
Duration of voice signal played out with signal synthesized from parameters or samples of data preceding and following in time due to voice data not received on time (or lost) from voice gateway for this call. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallActiveGapFillWithRedundancy 2.9.63.1.3.2.1.12
Duration of voice signal played out with signal synthesized from redundancy parameters available due to voice data not received on time (or lost) from voice gateway for this call. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallActiveHiWaterPlayoutDelay 2.9.63.1.3.2.1.13
The high water mark Voice Playout FIFO Delay during the voice call. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallActiveLoWaterPlayoutDelay 2.9.63.1.3.2.1.14
The low water mark Voice Playout FIFO Delay during the voice call.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cvVoIPCallActiveReceiveDelay 2.9.63.1.3.2.1.15
The average Playout FIFO Delay plus the decoder delay during the voice call.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cvVoIPCallActiveVADEnable 2.9.63.1.3.2.1.16
The object indicates whether or not the VAD (Voice Activity Detection) was enabled for the voice call.
Status: deprecated Access: read-only
OBJECT-TYPE    
  TruthValue  

cvVoIPCallActiveCoderTypeRate 2.9.63.1.3.2.1.17
The negotiated coder rate. It specifies the transmit rate of voice/fax compression to its associated call leg for the call. This rate is different from the configuration rate because of rate negotiation during the call.
Status: deprecated Access: read-only
OBJECT-TYPE    
  CvcCoderTypeRate  

cvVoIPCallActiveLostPackets 2.9.63.1.3.2.1.18
The number of lost voice packets during the call.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallActiveEarlyPackets 2.9.63.1.3.2.1.19
The number of received voice packets that arrived too early to store in jitter buffer during the call.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallActiveLatePackets 2.9.63.1.3.2.1.20
The number of received voice packets that arrived too late to playout with CODEC (Coder/Decoder) during the call.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallActiveUsername 2.9.63.1.3.2.1.21
The textual identifier of the calling party (user) of the call. If the username is not available, then the value of this object will have a length of zero.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..16)  

cvVoIPCallActiveProtocolCallId 2.9.63.1.3.2.1.22
The protocol-specific call identifier for the VoIP call.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

cvVoIPCallActiveRemSigIPAddrT 2.9.63.1.3.2.1.23
This object specifies the type of address contained in the associated instance of cvVoIPCallActiveRemSigIPAddr.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

cvVoIPCallActiveRemSigIPAddr 2.9.63.1.3.2.1.24
Remote signalling IP address for the VoIP call.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

cvVoIPCallActiveRemSigPort 2.9.63.1.3.2.1.25
Remote signalling listener port to which to transmit voice packets.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

cvVoIPCallActiveRemMediaIPAddrT 2.9.63.1.3.2.1.26
This object specifies the type of address contained in the associated instance of cvVoIPCallActiveRemMediaIPAddr.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

cvVoIPCallActiveRemMediaIPAddr 2.9.63.1.3.2.1.27
Remote media end point IP address for the VoIP call.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

cvVoIPCallActiveRemMediaPort 2.9.63.1.3.2.1.28
Remote media end point listener port to which to transmit voice packets.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

cvVoIPCallActiveSRTPEnable 2.9.63.1.3.2.1.29
The object indicates whether or not the SRTP (Secured RTP) was enabled for the voice call.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cvVoIPCallActiveOctetAligned 2.9.63.1.3.2.1.30
If the object has a value true(1) octet align operation is used, and if the value is false(2), bandwidth efficient operation is used. This object is not instantiated when the object cvVoIPCallActiveCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cvVoIPCallActiveBitRates 2.9.63.1.3.2.1.31
This object indicates modes of Bit rates. This object is not instantiated when the object cvVoIPCallActiveCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  CvAmrNbBitRateMode  

cvVoIPCallActiveModeChgPeriod 2.9.63.1.3.2.1.32
The object indicates the interval (N frame-blocks) at which codec mode changes are allowed. This object is not instantiated when the object cvVoIPCallActiveCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..100  

cvVoIPCallActiveModeChgNeighbor 2.9.63.1.3.2.1.33
If the object has a value of true(1), mode changes will be made to only neighboring modes set to cvVoIPCallActiveBitRates object. If the value is false(2), mode changes will be allowed to any modes set to cvVoIPCallActiveBitRates object. This object is not instantiated when the object cvVoIPCallActiveCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cvVoIPCallActiveMaxPtime 2.9.63.1.3.2.1.34
The object indicates the maximum amount of media that can be encapsulated in a payload. Supported value is 20 msec. This object is not instantiated when the object cvVoIPCallActiveCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 20..100  

cvVoIPCallActiveCRC 2.9.63.1.3.2.1.35
If the object has a value of true(1), frame CRC will be included in the payload and if the value is false(2), frame CRC will not be included in the payload. This object is applicable only when RTP frame type is octet aligned. This object is not instantiated when the object cvVoIPCallActiveCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cvVoIPCallActiveRobustSorting 2.9.63.1.3.2.1.36
If the object has a value of true(1), payload employs robust sorting and if the value is false(2), payload does not employ robust sorting. This object is applicable only when RTP frame type is octet aligned. This object is not instantiated when the object cvVoIPCallActiveCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cvVoIPCallActiveEncap 2.9.63.1.3.2.1.37
The object indicates the RTP encapsulation type. Supported RTP encapsulation type is RFC3267. This object is not instantiated when the object cvVoIPCallActiveCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  CvAmrNbRtpEncap  

cvVoIPCallActiveInterleaving 2.9.63.1.3.2.1.38
The object indicates the maximum number of frame-blocks allowed in an interleaving group. It indicates that frame-block level interleaving will be used for that session. If this object is not set, interleaving is not used. This object is applicable only when RTP frame type is octet aligned. This object is not instantiated when the object cvVoIPCallActiveCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..50  

cvVoIPCallActivePtime 2.9.63.1.3.2.1.39
The object indicates the length of the time in milliseconds represented by the media of the packet. Supported value is 20 milliseconds. This object is not instantiated when the object cvVoIPCallActiveCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 20..100  

cvVoIPCallActiveChannels 2.9.63.1.3.2.1.40
The object indicates the number of audio channels. Supported value is 1. This object is not instantiated when the object cvVoIPCallActiveCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..6  

cvVoIPCallActiveCoderMode 2.9.63.1.3.2.1.41
The object indicates the iLBC codec mode. The value of this object is valid only if cvVoIPCallActiveCoderTypeRate is equal to 'iLBC'.
Status: current Access: read-only
OBJECT-TYPE    
  CvIlbcFrameMode  

cvVoIPCallActiveCallId 2.9.63.1.3.2.1.42
This object represents the call identifier for the active VoIP leg of the call.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cvVoIPCallActiveCallReferenceId 2.9.63.1.3.2.1.43
The call reference ID associates the video call entry and voice call entry of the same endpoint. An audio-only call may or may not have a valid call reference ID (i.e. value greater than zero), but in both cases, there will not be a video call entry associated with it. For a video call, the video-specific information is stored in a call entry in cVideoSessionActive of CISCO-VIDEO-SESSION-MIB, in which the call reference ID is also identified.
Status: current Access: read-only
OBJECT-TYPE    
  CvcCallReferenceIdOrZero  

ccVoIPCallActivePolicyName 2.9.63.1.3.2.1.44
This object holds the policy name. It could be media policy, DSCP policy etc.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

cvVoIPCallActiveReversedDirectionPeerAddress 2.9.63.1.3.2.1.45
This object store the reversed direction peer address If the address is not available, then it will have a length of zero. If the call is ingress then it contains called number and if the call is egress then it contains calling number.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

cvVoIPCallActiveSessionId 2.9.63.1.3.2.1.46
This object indicates the active session ID assigned by the call manager to identify call legs that belong to the same call session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvCallActiveDS0s 2.9.63.1.3.3
The current number of DS0 interfaces used for the active calls.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cvCallActiveDS0sHighThreshold 2.9.63.1.3.4
A high threshold used to determine when to generate the cvdcActiveDS0sHighNotification. This object represents the percentage of active DS0s in total number of DS0s.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

cvCallActiveDS0sLowThreshold 2.9.63.1.3.5
A low threshold used to determine when to generate the cvdcActiveDS0sLowNotification notification. This object represents the percentage of active DS0s in total number of DS0s.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

cvCallActiveDS0sHighNotifyEnable 2.9.63.1.3.6
Specifies whether or not cvdcActiveDS0sHighNotification should be generated. 'true' : Indicates that the cvdcActiveDS0sHighNotification generation is enabled. 'false': Indicates that cvdcActiveDS0sHighNotification generation is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvCallActiveDS0sLowNotifyEnable 2.9.63.1.3.7
Specifies whether or not cvdcActiveDS0sLowNotification should be generated. 'true' : Indicates that the cvdcActiveDS0sLowNotification generation is enabled. 'false': Indicates that cvdcActiveDS0sLowNotification generation is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvCallVolume 2.9.63.1.3.8
OBJECT IDENTIFIER    

cvCallVolConnTable 2.9.63.1.3.8.1
This table represents the number of active call connections for each call connection type in the voice gateway.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvCallVolConnEntry

cvCallVolConnEntry 2.9.63.1.3.8.1.1
An entry in the cvCallVolConnTable indicates number of active calls for a call connection type in the voice gateway.
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallVolConnEntry  

cvCallVolConnIndex 2.9.63.1.3.8.1.1.1
This object represents index to the cvCallVolConnTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallConnectionType  

cvCallVolConnActiveConnection 2.9.63.1.3.8.1.1.2
This object represents the total number of active calls for a connection type in the voice gateway.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..65535  

cvCallVolConnTotalActiveConnections 2.9.63.1.3.8.2
This object represents the total number of active call legs in the voice gateway.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..65535  

cvCallVolConnMaxCallConnectionLicenese 2.9.63.1.3.8.3
This object represents the licensed call capacity for a voice gateway. If the value is 0, no licensing is done and the gateway can be accomodate as many calls depending on its capability.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

cvCallVolPeerTable 2.9.63.1.3.8.4
This table represents the information about the usage of dialpeers configured in a voice gateway.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvCallVolPeerEntry

cvCallVolPeerEntry 2.9.63.1.3.8.4.1
Each entry represents a row in cvCallVolPeerTable and corresponds to the information about a dialpeer configured on the voice gateway.
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallVolPeerEntry  

cvCallVolPeerIncomingCalls 2.9.63.1.3.8.4.1.1
This object represents the total number of active calls that has selected the dialpeer as an incoming dialpeer.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..65535  

cvCallVolPeerOutgoingCalls 2.9.63.1.3.8.4.1.2
This object represents the total number of active calls that has selected the dialpeer as an outgoing dialpeer.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..65535  

cvCallVolIfTable 2.9.63.1.3.8.5
This table represents the information about the usage of an IP interface in a voice gateway for voice media calls. This table has a sparse-dependent relationship with ifTable. There exists an entry in this table, for each of the entries in ifTable where ifType is one of 'ethernetCsmacd' and 'softwareLoopback'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvCallVolIfEntry

cvCallVolIfEntry 2.9.63.1.3.8.5.1
Each entry represents a row in cvCallVolIfTable and corresponds to the information about an IP interface in the voice gateway.
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallVolIfEntry  

cvCallVolMediaIncomingCalls 2.9.63.1.3.8.5.1.1
This object represents the total number of inbound active media calls through this IP interface.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..65535  

cvCallVolMediaOutgoingCalls 2.9.63.1.3.8.5.1.2
This object represents the total number of outbound active media calls through the IP interface.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..65535  

cvCallRateMonitor 2.9.63.1.3.11
OBJECT IDENTIFIER    

cvCallRateMonitorEnable 2.9.63.1.3.11.1
This object represents the state of call-monitoring. A value of 'true' indicates that call-monitoring is enabled. A value of 'false' indicates that call-monitoring is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cvCallRateMonitorTime 2.9.63.1.3.11.2
This object represents the interval for which the gateway monitors the call-rate.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..12  

cvCallRate 2.9.63.1.3.11.3
This object represents the total number of calls handled by the gateway during the monitored time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..65535  

cvCallRateHiWaterMark 2.9.63.1.3.11.4
This object represents the high water mark for the number of calls handled by the gateway in an unit interval of cvCallRateMonitorTime, from the time the call-monitoring is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

cvCallHistoryTable 2.9.63.1.4.1
This table is the voice extension to the call history table of IETF Dial Control MIB. It contains voice encapsulation call leg information such as voice packet statistics, coder usage and end to end bandwidth of the call leg.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvCallHistoryEntry

cvCallHistoryEntry 2.9.63.1.4.1.1
The information regarding a single voice encapsulation call leg. The call leg entry is identified by using the same index objects that are used by Call Active table of IETF Dial Control MIB to identify the call. An entry of this table is created when its associated call history entry in the IETF Dial Control MIB is created and the call history entry contains the call establishment to a voice encapsulation peer. The entry is deleted when its associated call active entry in the IETF Dial Control MIB is deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallHistoryEntry  

cvCallHistoryConnectionId 2.9.63.1.4.1.1.1
The global connection identifier for the telephony leg, which was assigned to the call.
Status: current Access: read-only
OBJECT-TYPE    
  CvcGUid  

cvCallHistoryTxDuration 2.9.63.1.4.1.1.2
Duration of Transmit path open from this peer to the voice gateway for the call leg. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvCallHistoryVoiceTxDuration 2.9.63.1.4.1.1.3
Duration for this call leg. The Voice Utilization Rate can be obtained by dividing this by cvCallHistoryTXDuration object. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvCallHistoryFaxTxDuration 2.9.63.1.4.1.1.4
Duration of fax transmitted from this peer to voice gateway for this call leg. The FAX Utilization Rate can be obtained by dividing this by cvCallHistoryTXDuration object. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvCallHistoryCoderTypeRate 2.9.63.1.4.1.1.5
The negotiated coder rate. It specifies the transmit rate of voice/fax compression to its associated call leg for the call.
Status: current Access: read-only
OBJECT-TYPE    
  CvcCoderTypeRate  

cvCallHistoryNoiseLevel 2.9.63.1.4.1.1.6
The object contains the average noise level for the call leg.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -128..8  

cvCallHistoryACOMLevel 2.9.63.1.4.1.1.7
The object contains the average ACOM level for the call leg. The value -1 indicates the level can not be determined or level detection is disabled.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..127  

cvCallHistorySessionTarget 2.9.63.1.4.1.1.8
The object specifies the session target of the peer that is used for the call leg via telephony interface.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

cvCallHistoryImgPageCount 2.9.63.1.4.1.1.9
The number of FAX related image pages are received or transmitted via the peer for the call leg.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvCallHistoryCallingName 2.9.63.1.4.1.1.10
The calling party name of the call. If the name is not available, then it will have a length of zero.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

cvCallHistoryCallerIDBlock 2.9.63.1.4.1.1.11
The object indicates whether or not the caller ID feature is blocked for this call.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cvCallHistoryAccountCode 2.9.63.1.4.1.1.12
The object indicates the account code input to the call. It could be used by down stream billing server. The value of empty string indicates no account code input.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..50)  

cvCallHistoryCallId 2.9.63.1.4.1.1.13
This object represents the call identifier for the telephony leg, which was assigned to the call.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cvVoIPCallHistoryTable 2.9.63.1.4.2
This table is the VoIP extension to the call history table of IETF Dial Control MIB. It contains VoIP call leg information about specific VoIP call destination and the selected QoS for the call leg.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvVoIPCallHistoryEntry

cvVoIPCallHistoryEntry 2.9.63.1.4.2.1
The information regarding a single VoIP call leg. The call leg entry is identified by using the same index objects that are used by Call Active table of IETF Dial Control MIB to identify the call. An entry of this table is created when its associated call history entry in the IETF Dial Control MIB is created and the call history entry contains information for the call establishment to the peer on the IP backbone via a voice over IP peer. The entry is deleted when its associated call history entry in the IETF Dial Control MIB is deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  CvVoIPCallHistoryEntry  

cvVoIPCallHistoryConnectionId 2.9.63.1.4.2.1.1
The global connection identifier for the VoIP leg, which was assigned to the call.
Status: current Access: read-only
OBJECT-TYPE    
  CvcGUid  

cvVoIPCallHistoryRemoteIPAddress 2.9.63.1.4.2.1.2
Remote system IP address for the call.
Status: deprecated Access: read-only
OBJECT-TYPE    
  IpAddress  

cvVoIPCallHistoryRemoteUDPPort 2.9.63.1.4.2.1.3
Remote system UDP listener port to which to transmit voice packets for the call.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

cvVoIPCallHistoryRoundTripDelay 2.9.63.1.4.2.1.4
The voice packet round trip delay between local and the remote system on the IP backbone during the call.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cvVoIPCallHistorySelectedQoS 2.9.63.1.4.2.1.5
The selected RSVP QoS for the call.
Status: current Access: read-only
OBJECT-TYPE    
  QosService  

cvVoIPCallHistorySessionProtocol 2.9.63.1.4.2.1.6
The object specifies the session protocol to be used for Internet call between local and remote router via IP backbone.
Status: current Access: read-only
OBJECT-TYPE    
  CvSessionProtocol  

cvVoIPCallHistorySessionTarget 2.9.63.1.4.2.1.7
The object specifies the session target of the peer that is used for the Voice over IP call.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

cvVoIPCallHistoryOnTimeRvPlayout 2.9.63.1.4.2.1.8
Duration of voice playout from data received on time for this call. This plus the durations for the GapFills in the following entries gives the Total Voice Playout Duration for Active Voice. This does not include duration for which no data was sent by the Transmit end as voice signal, e.g., silence suppression and fax signal. The On Time Playout Rate can be computed by dividing this entry by the Total Voice Playout Duration. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallHistoryGapFillWithSilence 2.9.63.1.4.2.1.9
Duration of voice signal replaced with signal played out during silence due to voice data not received on time (or lost) from voice gateway this call. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallHistoryGapFillWithPrediction 2.9.63.1.4.2.1.10
Duration of voice signal played out with signal synthesized from parameters or samples of data preceding in time due to voice data not received on time (or lost) from voice gateway for this call. An example of such playout is frame-erasure or frame-concealment strategies in G.729 and G.723.1 compression algorithms. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallHistoryGapFillWithInterpolation 2.9.63.1.4.2.1.11
Duration of voice signal played out with signal synthesized from parameters or samples of data preceding and following in time due to voice data not received on time (or lost) from voice gateway for this call. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallHistoryGapFillWithRedundancy 2.9.63.1.4.2.1.12
Duration of voice signal played out with signal synthesized from redundancy parameters available due to voice data not received on time (or lost) from voice gateway for this call. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallHistoryHiWaterPlayoutDelay 2.9.63.1.4.2.1.13
The high water mark Voice Playout FIFO Delay during the voice call. This counter object will lock at the maximum value which is approximately two days.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallHistoryLoWaterPlayoutDelay 2.9.63.1.4.2.1.14
The low water mark Voice Playout FIFO Delay during the voice call.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cvVoIPCallHistoryReceiveDelay 2.9.63.1.4.2.1.15
The average Playout FIFO Delay plus the decoder delay during the voice call.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cvVoIPCallHistoryVADEnable 2.9.63.1.4.2.1.16
The object indicates whether or not the VAD (Voice Activity Detection) was enabled for the voice call.
Status: deprecated Access: read-only
OBJECT-TYPE    
  TruthValue  

cvVoIPCallHistoryCoderTypeRate 2.9.63.1.4.2.1.17
The negotiated coder rate. It specifies the transmit rate of voice/fax compression to its associated call leg for the call. This rate is different from the configuration rate because of rate negotiation during the call.
Status: deprecated Access: read-only
OBJECT-TYPE    
  CvcCoderTypeRate  

cvVoIPCallHistoryIcpif 2.9.63.1.4.2.1.18
The Calculated Planning Impairment Factor (Icpif) of the call that is associated to this call leg. The value in this object is computed by the following equation. Icpif of the call = Itotal (total impairment value) of the call - A (Expectation Factor) in the cvVoIPPeerCfgExpectFactor of the call leg associated peer. A value of -1 implies that Icpif was not calculated and is meaningless for this call.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..55  

cvVoIPCallHistoryLostPackets 2.9.63.1.4.2.1.19
The number of lost voice packets during the call.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallHistoryEarlyPackets 2.9.63.1.4.2.1.20
The number of received voice packets that are arrived too early to store in jitter buffer during the call.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallHistoryLatePackets 2.9.63.1.4.2.1.21
The number of received voice packets that are arrived too late to playout with CODEC (Coder/Decoder) during the call.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallHistoryUsername 2.9.63.1.4.2.1.22
The textual identifier of the calling party (user) of the call. If the username is not available, then the value of this object will have a length of zero.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..16)  

cvVoIPCallHistoryProtocolCallId 2.9.63.1.4.2.1.23
The protocol-specific call identifier for the VoIP call.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

cvVoIPCallHistoryRemSigIPAddrT 2.9.63.1.4.2.1.24
This object specifies the type of address contained in the associated instance of cvVoIPCallHistoryRemSigIPAddr.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

cvVoIPCallHistoryRemSigIPAddr 2.9.63.1.4.2.1.25
Remote signalling IP address for the VoIP call.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

cvVoIPCallHistoryRemSigPort 2.9.63.1.4.2.1.26
Remote signalling listener port to which to transmit voice packets.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

cvVoIPCallHistoryRemMediaIPAddrT 2.9.63.1.4.2.1.27
This object specifies the type of address contained in the associated instance of cvVoIPCallHistoryRemMediaIPAddr.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

cvVoIPCallHistoryRemMediaIPAddr 2.9.63.1.4.2.1.28
Remote media end point IP address for the VoIP call.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

cvVoIPCallHistoryRemMediaPort 2.9.63.1.4.2.1.29
Remote media end point listener port to which to transmit voice packets.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

cvVoIPCallHistorySRTPEnable 2.9.63.1.4.2.1.30
The object indicates whether or not the SRTP (Secured RTP) was enabled for the voice call.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cvVoIPCallHistoryFallbackIcpif 2.9.63.1.4.2.1.31
The Calculated Planning Impairment Factor (Icpif) of the call that is associated to this call leg. The value in this object is computed by the following equation. Icpif of the fallback probe = Itotal (total impairment value) - configured fallback (Expectation Factor). A value of 0 implies that Icpif was not calculated and is meaningless for this attempt.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cvVoIPCallHistoryFallbackLoss 2.9.63.1.4.2.1.32
FallbackLoss is the percentage of loss packets based on the total packets sent.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cvVoIPCallHistoryFallbackDelay 2.9.63.1.4.2.1.33
The FallbackDelay is calculated as follows - Take the sum of the round trips for all the probes, divide by the number of probes, and divide by two to get the one-way delay. Then add in jitter_in or jiter_out, which ever is higher.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cvVoIPCallHistoryOctetAligned 2.9.63.1.4.2.1.34
If the object has a value true(1) octet align operation is used, and if the value is false(2), bandwidth efficient operation is used. This object is not instantiated when the object cvVoIPCallHistoryCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cvVoIPCallHistoryBitRates 2.9.63.1.4.2.1.35
This object indicates modes of Bit rates. This object is not instantiated when the object cvVoIPCallHistoryCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  CvAmrNbBitRateMode  

cvVoIPCallHistoryModeChgPeriod 2.9.63.1.4.2.1.36
The object indicates the interval (N frame-blocks) at which codec mode changes are allowed. This object is not instantiated when the object cvVoIPCallHistoryCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..100  

cvVoIPCallHistoryModeChgNeighbor 2.9.63.1.4.2.1.37
If the object has a value of true(1), mode changes will be made to only neighboring modes set to cvVoIPCallHistoryBitRates object. If the value is false(2), mode changes will be allowed to any modes set to cvVoIPCallHistoryBitRates object. This object is not instantiated when the object cvVoIPCallHistoryCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cvVoIPCallHistoryMaxPtime 2.9.63.1.4.2.1.38
The object indicates the maximum amount of media that can be encapsulated in a payload. Supported value is 20 msec. This object is not instantiated when the object cvVoIPCallHistoryCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 20..100  

cvVoIPCallHistoryCRC 2.9.63.1.4.2.1.39
If the object has a value of true(1), frame CRC will be included in the payload and if the value is false(2), frame CRC will not be included in the payload. This object is applicable only when RTP frame type is octet aligned. This object is not instantiated when the object cvVoIPCallHistoryCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cvVoIPCallHistoryRobustSorting 2.9.63.1.4.2.1.40
If the object has a value of true(1), payload employs robust sorting and if the value is false(2), payload does not employ robust sorting. This object is applicable only when RTP frame type is octet aligned. This object is not instantiated when the object cvVoIPCallHistoryCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cvVoIPCallHistoryEncap 2.9.63.1.4.2.1.41
The object indicates the RTP encapsulation type. Supported RTP encapsulation type is RFC3267. This object is not instantiated when the object cvVoIPCallHistoryCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  CvAmrNbRtpEncap  

cvVoIPCallHistoryInterleaving 2.9.63.1.4.2.1.42
The object indicates the maximum number of frame-blocks allowed in an interleaving group. It indicates that frame-block level interleaving will be used for that session. If this object is not set, interleaving is not used. This object is applicable only when RTP frame type is octet aligned. This object is not instantiated when the object cvVoIPCallHistoryCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..50  

cvVoIPCallHistoryPtime 2.9.63.1.4.2.1.43
The object indicates the length of the time in milliseconds represented by the media of the packet. Supported value is 20 milliseconds. This object is not instantiated when the object cvVoIPCallHistoryCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 20..100  

cvVoIPCallHistoryChannels 2.9.63.1.4.2.1.44
The object indicates the number of audio channels. Supported value is 1. This object is not instantiated when the object cvVoIPCallHistoryCoderTypeRate is not equal to gsmAmrNb enum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..6  

cvVoIPCallHistoryCoderMode 2.9.63.1.4.2.1.45
The object indicates the iLBC mode. The value of this object is valid only if cvVoIPCallHistoryCoderTypeRate is equal to 'iLBC'.
Status: current Access: read-only
OBJECT-TYPE    
  CvIlbcFrameMode  

cvVoIPCallHistoryCallId 2.9.63.1.4.2.1.46
This object represents the call identifier for the VoIP leg, which was assigned to the call.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cvVoIPCallHistoryCallReferenceId 2.9.63.1.4.2.1.47
The call reference ID associates the video call entry and voice call entry of the same endpoint. An audio-only call may or may not have a valid call reference ID (i.e. value greater than zero), but in both cases, there will not be a video call entry associated with it. For a video call, the video-specific information is stored in a call entry in cVideoSessionActive of CISCO-VIDEO-SESSION-MIB, in which the call reference ID is also identified.
Status: current Access: read-only
OBJECT-TYPE    
  CvcCallReferenceIdOrZero  

cvVoIPCallHistorySessionId 2.9.63.1.4.2.1.48
This object indicates the session ID assigned by the call manager to identify call legs that belong to the same call session. This session ID (history) represents a completed call session, whereas the active session ID (cvVoIPCallActiveSessionId) represents an ongoing session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvCallVolumeStatsHistory 2.9.63.1.4.3
OBJECT IDENTIFIER    

cvCallRateStatsTable 2.9.63.1.4.3.1
This table represents voice call rate measurement in various interval lengths defined by the CvCallVolumeStatsIntvlType object. Each interval may contain one or more entries to allow for detailed measurement to be collected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvCallRateStatsEntry

cvCallRateStatsEntry 2.9.63.1.4.3.1.1
This is a conceptual-row in cvCallRateStatsTable This entry is created at the system initialization and is updated at every epoch based on CvCallVolumeStatsIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallRateStatsEntry  

cvCallRateStatsIntvlDurUnits 2.9.63.1.4.3.1.1.1
The Object indexes in Call Rate Table to select one among three interval-tables. The different types in this table are represented by CvCallVolumeStatsIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallVolumeStatsIntvlType  

cvCallRateStatsIntvlDur 2.9.63.1.4.3.1.1.2
This is an index that references to the different past periods in given in interval of call rate table. This range is 1-60 for Seconds and Minutes table wherein 1-72 for hours table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..72  

cvCallRateStatsMaxVal 2.9.63.1.4.3.1.1.3
This object indicates the maximum calls per second that occured for the given period for the given interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvCallRateStatsAvgVal 2.9.63.1.4.3.1.1.4
This object indicates the average calls per second that occured for the given period for the given interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvCallLegRateStatsTable 2.9.63.1.4.3.2
cvCallLegRateStatsTable table represents voice call leg rate measurement in various interval lengths defined by the CvCallVolumeStatsIntvlType object. Each interval may contain one or more entries to allow for detailed measurement to be collected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvCallLegRateStatsEntry

cvCallLegRateStatsEntry 2.9.63.1.4.3.2.1
This is a conceptual-row in cvCallLegRateStatsTable This entry is created at the system initialization and is updated at every epoch based on CvCallVolumeStatsIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallLegRateStatsEntry  

cvCallLegRateStatsIntvlDurUnits 2.9.63.1.4.3.2.1.1
The Object indexes in Call Leg Rate Table to select one among three interval-tables. The different types in this table are represented by CvCallVolumeStatsIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallVolumeStatsIntvlType  

cvCallLegRateStatsIntvlDur 2.9.63.1.4.3.2.1.2
This is an index that references to the different past periods in given in interval of call rate table. This range is 1-60 for Seconds and Minutes table wherein 1-72 for hours table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..72  

cvCallLegRateStatsMaxVal 2.9.63.1.4.3.2.1.3
This object indicates the maximum call-legs per second that occured for the given period for the given interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvCallLegRateStatsAvgVal 2.9.63.1.4.3.2.1.4
This object indicates the average call-legs per second that occured for the given period for the given interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvActiveCallStatsTable 2.9.63.1.4.3.3
This table represents the active voice calls in various interval lengths defined by the CvCallVolumeStatsIntvlType object. Each interval may contain one or more entries to allow for detailed measurement to be collected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvActiveCallStatsEntry

cvActiveCallStatsEntry 2.9.63.1.4.3.3.1
This is a conceptual-row in cvActiveCallStatsTable This entry is created at the system initialization and is updated at every epoch based on CvCallVolumeStatsIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvActiveCallStatsEntry  

cvActiveCallStatsIntvlDurUnits 2.9.63.1.4.3.3.1.1
The Object indexes in Active Call Rate Table (con-current calls table) to select one among three interval-tables. The different types in this table are represented by CvCallVolumeStatsIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallVolumeStatsIntvlType  

cvActiveCallStatsIntvlDur 2.9.63.1.4.3.3.1.2
This is an index that references to the different past periods in given in interval of active call table. This range is 1-60 for Seconds and Minutes table wherein 1-72 for hours table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..72  

cvActiveCallStatsMaxVal 2.9.63.1.4.3.3.1.3
This object indicates the maximum number of active call that occured for the given period for the given interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvActiveCallStatsAvgVal 2.9.63.1.4.3.3.1.4
This object indicates the average number of active calls that occured for the given period for the given interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvCallDurationStatsTable 2.9.63.1.4.3.4
This table represents the number of calls below a specific duration in various interval length defined by the CvCallVolumeStatsIntvlType object. The specific duration is configurable value of cvCallDurationStatsThreshold object. Each interval may contain one or more entries to allow for detailed measurement to be collected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvCallDurationStatsEntry

cvCallDurationStatsEntry 2.9.63.1.4.3.4.1
This is a conceptual-row in cvCallDurationStatsTable This entry is created at the system initialization and is updated at every epoch based on CvCallVolumeStatsIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallDurationStatsEntry  

cvCallDurationStatsIntvlDurUnits 2.9.63.1.4.3.4.1.1
The Object indexes in Call Duration Table to select one among three interval-tables. The different types in this table are represented by CvCallVolumeStatsIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallVolumeStatsIntvlType  

cvCallDurationStatsIntvlDur 2.9.63.1.4.3.4.1.2
This is an index that references to the different past periods in given in interval of call Duration table. This range is 1-60 for Seconds and Minutes table wherein 1-72 for hours table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..72  

cvCallDurationStatsMaxVal 2.9.63.1.4.3.4.1.3
This object indicates the maximum number of calls having a duration which is below the threshold for the given interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvCallDurationStatsAvgVal 2.9.63.1.4.3.4.1.4
This object indicates the average number of calls having a duration which is below the threshold for the given interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvSipMsgRateStatsTable 2.9.63.1.4.3.5
This table represents the SIP message rate measurement in various interval length defined by the CvCallVolumeStatsIntvlType object. Each interval may contain one or more entries to allow for detailed measurement to be collected
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvSipMsgRateStatsEntry

cvSipMsgRateStatsEntry 2.9.63.1.4.3.5.1
This is a conceptual-row in cvSipMsgRateStatsTable This entry is created at the system initialization and is updated at every epoch based on CvCallVolumeStatsIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvSipMsgRateStatsEntry  

cvSipMsgRateStatsIntvlDurUnits 2.9.63.1.4.3.5.1.1
The Object indexes in SIP Message Rate Table to select one among three interval-tables. The different types in this table are represented by CvCallVolumeStatsIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallVolumeStatsIntvlType  

cvSipMsgRateStatsIntvlDur 2.9.63.1.4.3.5.1.2
This is an index that references to the different past periods in given in interval of SIP message rate table. This range is 1-60 for Seconds and Minutes table wherein 1-72 for hours table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..72  

cvSipMsgRateStatsMaxVal 2.9.63.1.4.3.5.1.3
This object indicates the maximum SIP messages per second that is received for the given interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvSipMsgRateStatsAvgVal 2.9.63.1.4.3.5.1.4
This object indicates the average SIP messages per second that is received for the given interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvCallRateWMTable 2.9.63.1.4.3.6
This table represents high watermarks achieved by call rate in various interval length defined by CvCallVolumeWMIntvlType. Each interval may contain one or more entries to allow for detailed measurement to be collected
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvCallRateWMEntry

cvCallRateWMEntry 2.9.63.1.4.3.6.1
This is a conceptual-row in cvCallRateWMTable This entry is created at the system initialization and is updated whenever a) This entry is obsolete OR b) A new/higher entry is available. These entries are reinitialised/added/deleted if cvCallVolumeWMTableSize is changed
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallRateWMEntry  

cvCallRateWMIntvlDurUnits 2.9.63.1.4.3.6.1.1
The Object indexes in call rate Water mark Table to select one among four interval-tables. The different types in this table are represented by CvCallVolumeWMIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallVolumeWMIntvlType  

cvCallRateWMIndex 2.9.63.1.4.3.6.1.2
This is an index that references to different peaks in past period in call rate watermark table. The number of watermarks entries stored for each table are based on cvCallVolumeWMTableSize
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..10  

cvCallRateWMValue 2.9.63.1.4.3.6.1.3
This object indicates high watermark value achieved by the calls per second for the given interval
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvCallRateWMts 2.9.63.1.4.3.6.1.4
This object indicates date and Time when the high watermark is achieved for calls per second for the given interval
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

cvCallLegRateWMTable 2.9.63.1.4.3.7
cvCallLegRateWMTable table represents high watermarks achieved by call-leg rate in various interval length defined by CvCallVolumeWMIntvlType. Each interval may contain one or more entries to allow for detailed measurement to be collected
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvCallLegRateWMEntry

cvCallLegRateWMEntry 2.9.63.1.4.3.7.1
This is a conceptual-row in cvCallLegRateWMTable This entry is created at the system initialization and is updated whenever a) This entry is obsolete OR b) A new/higher entry is available. These entries are reinitialised/added/deleted if cvCallVolumeWMTableSize is changed
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallLegRateWMEntry  

cvCallLegRateWMIntvlDurUnits 2.9.63.1.4.3.7.1.1
The Object indexes in call leg rate Water mark Table to select one among four interval-tables. The different types in this table are represented by CvCallVolumeWMIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallVolumeWMIntvlType  

cvCallLegRateWMIndex 2.9.63.1.4.3.7.1.2
This is an index that references to different peaks in past period in call leg rate watermark table. The number of watermarks entries stored for each table are based on cvCallVolumeWMTableSize
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..10  

cvCallLegRateWMValue 2.9.63.1.4.3.7.1.3
This object indicates high watermark value achieved by the call legs per second for the given interval
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvCallLegRateWMts 2.9.63.1.4.3.7.1.4
This object indicates date and time when the high watermark is achieved for call-legs per second for the given interval
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

cvActiveCallWMTable 2.9.63.1.4.3.8
This table represents high watermarks achieved by active calls in various interval length defined by CvCallVolumeWMIntvlType. Each interval may contain one or more entries to allow for detailed measurement to be collected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvActiveCallWMEntry

cvActiveCallWMEntry 2.9.63.1.4.3.8.1
This is a conceptual-row in cvActiveCallWMTable This entry is created at the system initialization and is updated whenever a) This entry is obsolete OR b) A new/higher entry is available. These entries are reinitialised/added/deleted if cvCallVolumeWMTableSize is changed
Status: current Access: not-accessible
OBJECT-TYPE    
  CvActiveCallWMEntry  

cvActiveCallWMIntvlDurUnits 2.9.63.1.4.3.8.1.1
The Object indexes in active call Water mark Table to select one among four interval-tables. The different types in this table are represented by CvCallVolumeWMIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallVolumeWMIntvlType  

cvActiveCallWMIndex 2.9.63.1.4.3.8.1.2
This is an index that references to different peaks in past period in acive call watermark table. The number of watermarks entries stored for each table are based on cvCallVolumeWMTableSize
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..10  

cvActiveCallWMValue 2.9.63.1.4.3.8.1.3
This object indicates high watermark value achieved by the active calls for the given interval
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvActiveCallWMts 2.9.63.1.4.3.8.1.4
This object indicates date and time when the high watermark is achieved for active calls for the given interval
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

cvSipMsgRateWMTable 2.9.63.1.4.3.9
This table represents of high watermarks achieved by SIP message rate in various interval length defined by CvCallVolumeWMIntvlType. Each interval may contain one or more entries to allow for detailed measurement to be collected
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CvSipMsgRateWMEntry

cvSipMsgRateWMEntry 2.9.63.1.4.3.9.1
This is a conceptual-row in cvSipMsgRateWMTable. This entry is created at the system initialization and is updated whenever a) This entry is obsolete OR b) A new/higher entry is available. These entries are reinitialised/added/deleted if cvCallVolumeWMTableSize is changed
Status: current Access: not-accessible
OBJECT-TYPE    
  CvSipMsgRateWMEntry  

cvSipMsgRateWMIntvlDurUnits 2.9.63.1.4.3.9.1.1
The Object indexes in SIP Message rate Water mark Table to select one among four interval-tables. The different types in this table are represented by CvCallVolumeWMIntvlType
Status: current Access: not-accessible
OBJECT-TYPE    
  CvCallVolumeWMIntvlType  

cvSipMsgRateWMIndex 2.9.63.1.4.3.9.1.2
This is an index that references to different peaks in past period in sip message rate watermark table. The number of watermarks entries stored for each table are based on cvCallVolumeWMTableSize
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..10  

cvSipMsgRateWMValue 2.9.63.1.4.3.9.1.3
This object indicates high watermark value achieved by the SIP messages per second for the given interval
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cvSipMsgRateWMts 2.9.63.1.4.3.9.1.4
This object indicates date and time when the high watermark is achieved for SIP messages per second for the given interval
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

cvCallDurationStatsThreshold 2.9.63.1.4.3.10
This Object specifies the thresold duration in seconds. cvCallDurationStatsTable will monitor all the calls below this threshold. Decresing the value of the threshold will reset this table.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..3600  

cvCallVolumeWMTableSize 2.9.63.1.4.3.11
This Object specifies the number of entries the watermark table will maintain. This value will decide the number of elements in cvCallRateWMTable, cvCallLegRateWMTable, cvActiveCallWMTable and cvSipMsgRateWMTable.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 3..10  

cvdcMIBNotificationPrefix 2.9.63.2
OBJECT IDENTIFIER    

cvdcMIBNotifications 2.9.63.2.0
OBJECT IDENTIFIER    

cvdcPoorQoVNotification 2.9.63.2.0.1
Poor quality of voice notification. A cvdcPoorQoVNotification is sent at the call disconnection time if the value of cvVoIPCallHistoryIcpif exceeds the value of cvVoIPPeerCfgIcpif in the call associated peer.
Status: deprecated Access: read-write
NOTIFICATION-TYPE    

cvdcPoorQoVNotificationRev1 2.9.63.2.0.2
Poor quality of voice notification. A cvdcPoorQoVNotificationRev1 is sent at the call disconnection time if the value of cvVoIPCallHistoryIcpif exceeds the value of cvVoIPPeerCfgIcpif in the call associated peer.
Status: current Access: read-write
NOTIFICATION-TYPE    

cvdcActiveDS0sHighNotification 2.9.63.2.0.3
The cvdcActiveDS0sHighNotification is sent when the percentage of active DS0s exceeds cvCallActiveDS0sHighThreshold value.
Status: current Access: read-write
NOTIFICATION-TYPE    

cvdcActiveDS0sLowNotification 2.9.63.2.0.4
The cvdcActiveDS0sLowNotification is sent when the percentage of active DS0s is less than cvCallActiveDS0sLowThreshold value.
Status: current Access: read-write
NOTIFICATION-TYPE    

cvdcFallbackNotification 2.9.63.2.0.5
This cvdcFallbackNotificaion is sent out, when the destination IP address of call fallback probe fails. This probe generated for beginning of each call, with exception of existing cached entry.
Status: current Access: read-write
NOTIFICATION-TYPE    

cvdcPolicyViolationNotification 2.9.63.2.0.6
Policy violation voice notification. A cvdcPolicyViolationNotification is sent when the call is active and has policy violation. It can be media policy violation or DSCP policy violation.
Status: current Access: read-write
NOTIFICATION-TYPE    

cvdcMIBConformance 2.9.63.3
OBJECT IDENTIFIER    

cvdcMIBCompliances 2.9.63.3.1
OBJECT IDENTIFIER    

cvdcMIBGroups 2.9.63.3.2
OBJECT IDENTIFIER    

cvdcMIBCompliance 2.9.63.3.1.1
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev1 2.9.63.3.1.2
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev2 2.9.63.3.1.3
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev3 2.9.63.3.1.4
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev4 2.9.63.3.1.5
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev5 2.9.63.3.1.6
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev6 2.9.63.3.1.7
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev7 2.9.63.3.1.8
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev8 2.9.63.3.1.9
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev9 2.9.63.3.1.10
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev10 2.9.63.3.1.11
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev11 2.9.63.3.1.12
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev12 2.9.63.3.1.13
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev13 2.9.63.3.1.14
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev14 2.9.63.3.1.15
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev15 2.9.63.3.1.16
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev16 2.9.63.3.1.17
The compliance statement for entities which implement the CISCO VOICE DIAL CONTROL MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev17 2.9.63.3.1.18
The compliance statement for the entities that implement CISCO-VOICE-DIAL-CONTROL-MIB.
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev18 2.9.63.3.1.19
The compliance statement for the entities that implement CISCO-VOICE-DIAL-CONTROL-MIB.
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev19 2.9.63.3.1.20
The compliance statement for the entities that implement CISCO-VOICE-DIAL-CONTROL-MIB.
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev20 2.9.63.3.1.21
The compliance statement for the entities that implement CISCO-VOICE-DIAL-CONTROL-MIB.
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev21 2.9.63.3.1.22
The compliance statement for the entities that implement CISCO-VOICE-DIAL-CONTROL-MIB.
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cvdcMIBComplianceRev22 2.9.63.3.1.23
The compliance statement for the entities that implement CISCO-VOICE-DIAL-CONTROL-MIB.
Status: current Access: read-write
MODULE-COMPLIANCE    

cvdcGeneralCfgGroup 2.9.63.3.2.1
A collection of objects providing the general Voice Gateway Call Dial Control configuration capability. cvdcGeneralCfgGroup group is superseded by cvdcGeneralCfgGroupRev1.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvdcVoiceCfgGroup 2.9.63.3.2.2
A collection of objects providing the GSTN (General Switched Telephony Network Voice Dial Control configuration capability. GSTN (General Switched Telephony Network), which is supposed to encompass analog, ISDN, Cellular - essentially anything circuit switched over the TDM infrastructure. cvdcVoiceCfgGroup group is superseded by cvdcVoiceCfgGroupRev1.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvdcVoIPCfgGroup 2.9.63.3.2.3
A collection of objects providing the VoIP Dial Control configuration capability. cvdcVoIPCfgGroup group is superseded by cvdcVoIPCfgGroupRev1.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvCallGroup 2.9.63.3.2.4
A collection of objects providing the GSTN (General Switched Telephony Network Voice Call capability. GSTN (General Switched Telephony Network), which is supposed to encompass analog, ISDN, Cellular - essentially anything circuit switched over the TDM infrastructure. cvCallGroup group is superseded by cvCallGroupRev1.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvVoIPCallGroup 2.9.63.3.2.5
A collection of objects providing the VoIP Call capability. cvVoIPCallGroup group is superseded by cvVoIPCallGroupRev1.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvdcGeneralCfgGroupRev1 2.9.63.3.2.6
A collection of objects providing the general Voice Gateway Call Dial Control configuration capability. cvdcGeneralCfgGroupRev1 group is superseded by cvdcGeneralCfgGroupRev2.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvdcVoiceCfgGroupRev1 2.9.63.3.2.7
A collection of objects providing the GSTN (General Switched Telephony Network Voice Dial Control configuration capability. GSTN (General Switched Telephony Network), which is supposed to encompass analog, ISDN, Cellular - essentially anything circuit switched over the TDM infrastructure. cvdcVoiceCfgGroupRev1 group is superseded by cvdcVoiceCfgGroupRev2.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvVoIPCallGroupRev1 2.9.63.3.2.8
A collection of objects providing the VoIP Call capability. cvVoIPCallGroupRev1 group is superseded by cvVoIPCallGroupRev2.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvCallGroupRev1 2.9.63.3.2.9
A collection of objects providing the GSTN (General Switched Telephony Network Voice Dial Control configuration capability. GSTN (General Switched Telephony Network), which is supposed to encompass analog, ISDN, Cellular - essentially anything circuit switched over the TDM infrastructure. cvCallGroupRev1 group is superseded by cvCallGroupRev2.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvdcGeneralCfgGroupRev2 2.9.63.3.2.10
A collection of objects providing the general Voice Gateway Call Dial Control configuration capability. cvdcGeneralCfgGroupRev2 group is superseded by cvdcGeneralCfgGroupRev3.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvdcVoIPCfgGroupRev1 2.9.63.3.2.11
A collection of objects providing the VoIP Dial Control configuration capability. cvdcVoIPCfgGroupRev1 group is superseded by cvdcVoIPCfgGroupRev2.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvdcGeneralCfgGroupRev3 2.9.63.3.2.12
A collection of objects providing the general Voice Gateway Call Dial Control configuration capability. cvdcGeneralCfgGroupRev3 group is superseded by cvdcGeneralCfgGroupRev4.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvdcVoiceCfgGroupRev2 2.9.63.3.2.13
A collection of objects providing the GSTN (General Switched Telephony Network Voice Dial Control configuration capability. GSTN (General Switched Telephony Network), which is supposed to encompass analog, ISDN, Cellular - essentially anything circuit switched over the TDM infrastructure.
Status: current Access: read-write
OBJECT-GROUP    

cvdcVoIPCfgGroupRev2 2.9.63.3.2.14
A collection of objects providing the VoIP Dial Control configuration capability. cvdcVoIPCfgGroupRev2 group is superseded by cvdcVoIPCfgGroupRev3.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvVoIPCallGroupRev3 2.9.63.3.2.15
A collection of objects providing the VoIP Call capability. cvVoIPCallGroupRev3 group is superseded by cvVoIPCallGroupRev4.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvdcNotificationGroup 2.9.63.3.2.16
The notifications for the CISCO-VOICE-DIAL-CONTROL-MIB cvdcNotificationGroup group is superseded by cvdcNotificationGroupRev1.
Status: deprecated Access: read-write
NOTIFICATION-GROUP    

cvCallGroupRev2 2.9.63.3.2.17
A collection of objects providing the GSTN (General Switched Telephony Network Voice Dial Control configuration capability. GSTN (General Switched Telephony Network), which is supposed to encompass analog, ISDN, Cellular - essentially anything circuit switched over the TDM infrastructure. cvCallGroupRev2 group is superseded by cvCallGroupRev3.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvdcGeneralCfgGroupRev4 2.9.63.3.2.18
A collection of objects providing the general Voice Gateway Call Dial Control configuration capability. cvdcGeneralCfgGroupRev4 group is superseded by cvdcGeneralCfgGroupRev5.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvVoIPCallGroupRev4 2.9.63.3.2.19
A collection of objects providing the VoIP Call capability. cvVoIPCallGroupRev4 group is superseded by cvVoIPCallGroupRev5.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvdcNotificationGroupRev1 2.9.63.3.2.20
The notifications for the CISCO-VOICE-DIAL-CONTROL-MIB cvdcNotificationGroupRev1 group is superseded by cvdcNotificationGroupRev2.
Status: deprecated Access: read-write
NOTIFICATION-GROUP    

cvdcVoIPCfgGroupRev3 2.9.63.3.2.21
A collection of objects providing the VoIP Dial Control configuration capability. cvdcVoIPCfgGroupRev3 group is superseded by cvdcVoIPCfgGroupRev4.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvdcGeneralCfgGroupRev5 2.9.63.3.2.22
A collection of objects providing the general Voice Gateway Call Dial Control configuration capability. cvdcGeneralCfgGroupRev5 group is superseded by cvdcGeneralCfgGroupRev6.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvdcVoIPCfgGroupRev4 2.9.63.3.2.23
A collection of objects providing the VoIP Dial Control configuration capability.
Status: current Access: read-write
OBJECT-GROUP    

cvCallGroupRev3 2.9.63.3.2.24
A collection of objects providing the GSTN (General Switched Telephony Network Voice Dial Control configuration capability. GSTN (General Switched Telephony Network), which is supposed to encompass analog, ISDN, Cellular - essentially anything circuit switched over the TDM infrastructure. cvCallGroupRev3 group is superseded by cvCallGroupRev4.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvCallGroupRev4 2.9.63.3.2.25
A collection of objects providing the GSTN (General Switched Telephony Network Voice Dial Control configuration capability. GSTN (General Switched Telephony Network), which is supposed to encompass analog, ISDN, Cellular - essentially anything circuit switched over the TDM infrastructure. cvCallGroupRev4 group is superseded by cvCallGroupRev5.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvVoIPCallGroupRev5 2.9.63.3.2.26
A collection of objects providing the VoIP Call capability. cvVoIPCallGroupRev5 group is superseded by cvVoIPCallGroupRev6.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvCallGroupRev5 2.9.63.3.2.27
A collection of objects providing the GSTN (General Switched Telephony Network Voice Dial Control configuration capability. GSTN (General Switched Telephony Network), which is supposed to encompass analog, ISDN, Cellular - essentially anything circuit switched over the TDM infrastructure.
Status: current Access: read-write
OBJECT-GROUP    

cvdcNotificationGroupRev2 2.9.63.3.2.28
The notifications for the CISCO-VOICE-DIAL-CONTROL-MIB cvdcNotificationGroupRev2 group is superseded by cvdcNotificationGroupRev3.
Status: deprecated Access: read-write
NOTIFICATION-GROUP    

cvVoIPCallGroupRev6 2.9.63.3.2.29
A collection of objects providing the VoIP Call capability.
Status: current Access: read-write
OBJECT-GROUP    

cvdcGeneralCfgGroupRev6 2.9.63.3.2.30
A collection of objects providing the general Voice Gateway Call Dial Control configuration capability.
Status: current Access: read-write
OBJECT-GROUP    

cvdcNotificationGroupRev3 2.9.63.3.2.31
The notifications for the CISCO-VOICE-DIAL-CONTROL-MIB. This group cvdcNotificationGroupRev3 is deprecated and replaced by cvdcNotificationGroupRev4. cvdcNotificationGroupRev3 group is superseded by cvdcNotificationGroupRev4.
Status: deprecated Access: read-write
NOTIFICATION-GROUP    

cvdcVoIPCfgAmrNbGroup 2.9.63.3.2.32
A collection of objects providing the VoIP Dial Control configuration capability for GSM AMR-NB codec.
Status: current Access: read-write
OBJECT-GROUP    

cvVoIPCallAmrNbGroup 2.9.63.3.2.33
A collection of objects providing GSM AMR-NB codec related information.
Status: current Access: read-write
OBJECT-GROUP    

cvdcVoIPCfgIlbcGroup 2.9.63.3.2.34
A collection of objects providing the VoIP Dial Control configuration capability for iLBC codec.
Status: current Access: read-write
OBJECT-GROUP    

cvVoIPCallIlbcGroup 2.9.63.3.2.35
A collection of objects providing iLBC codec related information.
Status: current Access: read-write
OBJECT-GROUP    

cvCallGroupSup1 2.9.63.3.2.36
This group supplements cvCallGroup to provide the call identifier for the telephony leg of the gateway call.
Status: current Access: read-write
OBJECT-GROUP    

cvVoIPCallGroupSup1 2.9.63.3.2.37
This group supplements cvVoIPCallGroup to provide the call identifier for the VoIP leg of the gateway call. The group cvVoIPCallGroupSup1 is deprecated and replaced by cvVoIPCallGroupSup2.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvCallVolumeGroup 2.9.63.3.2.38
This group provides the information about the call-volume in the voice gateway.
Status: current Access: read-write
OBJECT-GROUP    

cvCallRateMonitorGroup 2.9.63.3.2.39
This group represents the objects used to monitor the call-rate.
Status: current Access: read-write
OBJECT-GROUP    

cvdcVoIPCfgISACGroup 2.9.63.3.2.40
A collection of objects providing iSAC codec related information.
Status: current Access: read-write
OBJECT-GROUP    

cvdcNotificationGroupRev4 2.9.63.3.2.41
The notifications for the CISCO-VOICE-DIAL-CONTROL-MIB.
Status: current Access: read-write
NOTIFICATION-GROUP    

cvVoIPCallGroupSup2 2.9.63.3.2.42
This group supplements cvVoIPCallGroup to provide the call identifier and policy for the VoIP leg of the gateway call. cvVoIPCallGroupSup2 group is superseded by cvVoIPCallGroupSup3.
Status: deprecated Access: read-write
OBJECT-GROUP    

cvVoIPCallGroupSup3 2.9.63.3.2.43
This group supplements cvVoIPCallGroup to identify the VoIP leg of the gateway call.
Status: current Access: read-write
OBJECT-GROUP    

cvdcCallVolumeStatsHistory 2.9.63.3.2.44
This group provides the information about the Call Volume Stats History information in the voice gateway.
Status: current Access: read-write
OBJECT-GROUP