CISCO-TELEPRESENCE-MIB

File: CISCO-TELEPRESENCE-MIB.mib (70643 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
SNMP-FRAMEWORK-MIB INET-ADDRESS-MIB IF-MIB
CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
NOTIFICATION-TYPE MODULE-COMPLIANCE NOTIFICATION-GROUP
OBJECT-GROUP TEXTUAL-CONVENTION TruthValue
TimeStamp SnmpAdminString InetAddress
InetAddressType InterfaceIndexOrZero ciscoMgmt

Defined Types

CtpSystemResetMode  
This textual convention identifies the system reset mode. noRestart (1) -- No operation. restartPending (2) -- Restart a system without shutting down when there is no active call; otherwise, system will be restarted after the call is terminated. resetPending (3) -- Shut down a system and bring it back up if there is no active call; otherwise, system will be reset after the call is terminated. forceReset (4) -- Shut down a system and bring it back up no matter if there is an active call or not.
TEXTUAL-CONVENTION    
  INTEGER noRestart(1), restartPending(2), resetPending(3), forceReset(4)  

CtpPeripheralCableCode  
The textual convention identifies cable status of the attached peripheral through HDMI. plugged (1) -- Peripheral cable is plugged. loose (2) -- Peripheral cable is loose. unplugged (3) -- Peripheral cable is unplugged. unknown (4) -- Cannot detect peripheral cable status. internalError (5) -- Internal error.
TEXTUAL-CONVENTION    
  INTEGER plugged(1), loose(2), unplugged(3), unknown(4), internalError(5)  

CtpPeripheralPowerCode  
The textual convention identifies power status of the attached peripheral through HDMI. on (1) -- Peripheral power is on. standby (2) -- Peripheral power is in standby mode. off (3) -- Peripheral power is off. unknown (4) -- Cannot detect peripheral power status. internalError (5) -- Internal error.
TEXTUAL-CONVENTION    
  INTEGER on(1), standby(2), off(3), unknown(4), internalError(5)  

CtpPeripheralStatusCode  
The textual convention identifies the peripheral status. noError (0) -- Expected peripheral device is functioning through the attached port. other (1) -- None of the listed state. cableError (2) -- Expected peripheral device has cabling issue. powerError (3) -- Expected peripheral device has power issue. mgmtSysConfigError (4) -- Expected peripheral device has communications management system configuration issue. systemError (5) -- Telepresence system error. deviceError (6) -- Expected peripheral device is attached but not fully functional. linkError (7) -- Expected peripheral device has port level link issue. commError (8) -- Expected peripheral device has port level communication issue. detectionDisabled (9) -- Status detection has been disabled.
TEXTUAL-CONVENTION    
  INTEGER noError(0), other(1), cableError(2), powerError(3), mgmtSysConfigError(4), systemError(5), deviceError(6), linkError(7), commError(8), detectionDisabled(9)  

CtpSystemAccessProtocol  
The textual convention identifies supported Telepresence user access protocol. http (1) -- Hypertext Transfer Protocol (HTTP) snmp (2) -- Simple Network Management Protocol (SNMP) ssh (3) -- Secure Shell (SSH)
TEXTUAL-CONVENTION    
  INTEGER http(1), snmp(2), ssh(3)  

CtpPeripheralDeviceCategoryCode  
The textual convention identifies the peripheral type. unknown (0) -- Unknown Device other (1) -- None of the listed device uplinkDevice (2) -- Device attached to CTS uplink port ipPhone (3) -- IP phone camera (4) -- Camera display (5) -- Display secCodec (6) -- CTS secondary codec docCamera (7) -- Document camera projector (8) -- Projector dviDevice (9) -- Device attached to DVI port presentationCodec (10) -- CTS codec process presentation -- stream auxiliaryControlUnit (11) -- Auxiliary control unit audioExpansionUnit (12) -- Audio expansion unit microphone (13) -- Microphone headset (14) -- Headset positionMic (15) -- Position microphone digitalMediaSystem (16) -- Digitial Media System auxHDMIOuputDevice (17) -- Auxiliary HDMI output device uiDevice (18) -- User Interface device for CTS auxHDMIInputDevice (19) -- HDMI input enabled device bringYourOwnDevice (20) -- Bring Your Own Device, -- like PC,Laptop,Tablet etc
TEXTUAL-CONVENTION    
  INTEGER unknown(0), other(1), uplinkDevice(2), ipPhone(3), camera(4), display(5), secCodec(6), docCamera(7), projector(8), dviDevice(9), presentationCodec(10), auxiliaryControlUnit(11), audioExpansionUnit(12), microphone(13), headset(14), positionMic(15), digitialMediaSystem(16), auxHDMIOutputDevice(17), uiDevice(18), auxHDMIInputDevice(19), bringYourOwnDevice(20)  

CtpPeripheralStatusEntry  
SEQUENCE    
  ctpPeripheralIndex Unsigned32
  ctpPeripheralDescription SnmpAdminString
  ctpPeripheralStatus CtpPeripheralStatusCode
  ctpPeripheralDeviceCategory CtpPeripheralDeviceCategoryCode
  ctpPeripheralDeviceNumber Unsigned32

CtpEtherPeripheralStatusEntry  
SEQUENCE    
  ctpEtherPeripheralIndex Unsigned32
  ctpEtherPeripheralIfIndex InterfaceIndexOrZero
  ctpEtherPeripheralAddrType InetAddressType
  ctpEtherPeripheralAddr InetAddress
  ctpEtherPeripheralStatus CtpPeripheralStatusCode

CtpHDMIPeripheralStatusEntry  
SEQUENCE    
  ctpHDMIPeripheralIndex Unsigned32
  ctpHDMIPeripheralCableStatus CtpPeripheralCableCode
  ctpHDMIPeripheralPowerStatus CtpPeripheralPowerCode

CtpDVIPeripheralStatusEntry  
SEQUENCE    
  ctpDVIPeripheralIndex Unsigned32
  ctpDVIPeripheralCableStatus CtpPeripheralCableCode

CtpRS232PeripheralStatusEntry  
SEQUENCE    
  ctpRS232PeripheralIndex Unsigned32
  ctpRS232PortIndex InterfaceIndexOrZero
  ctpRS232PeripheralConnStatus INTEGER

CtpPeripheralAttributeEntry  
SEQUENCE    
  ctpPeripheralAttributeIndex Unsigned32
  ctpPeripheralAttributeDescr INTEGER
  ctpPeripheralAttributeValue Unsigned32

CtpUSBPeripheralStatusEntry  
SEQUENCE    
  ctpUSBPeripheralIndex Unsigned32
  ctpUSBPeripheralCableStatus CtpPeripheralCableCode
  ctpUSBPeripheralPowerStatus INTEGER
  ctpUSBPeripheralPortType INTEGER
  ctpUSBPeripheralPortRate INTEGER

Ctp802dot11PeripheralStatusEntry  
SEQUENCE    
  ctp802dot11PeripheralIndex Unsigned32
  ctp802dot11PeripheralIfIndex InterfaceIndexOrZero
  ctp802dot11PeripheralAddrType InetAddressType
  ctp802dot11PeripheralAddr InetAddress
  ctp802dot11PeripheralLinkStrength Unsigned32
  ctp802dot11PeripheralLinkStatus CtpPeripheralCableCode

CtpDPPeripheralStatusEntry  
SEQUENCE    
  ctpDPPeripheralIndex Unsigned32
  ctpDPPeripheralCableStatus CtpPeripheralCableCode
  ctpDPPeripheralPowerStatus CtpPeripheralPowerCode

CtpPeripheralErrorHistoryEntry  
SEQUENCE    
  ctpPeripheralErrorHistoryIndex Unsigned32
  ctpPeripheralErrorIndex Unsigned32
  ctpPeripheralErrorStatus CtpPeripheralStatusCode
  ctpPeripheralErrorTimeStamp TimeStamp
  ctpPeripheralErrorDeviceCategory CtpPeripheralDeviceCategoryCode
  ctpPeripheralErrorDeviceNumber Unsigned32

CtpSysUserAuthFailHistoryEntry  
SEQUENCE    
  ctpSysUserAuthFailHistoryIndex Unsigned32
  ctpSysUserAuthFailSourceAddrType InetAddressType
  ctpSysUserAuthFailSourceAddr InetAddress
  ctpSysUserAuthFailSourcePort Unsigned32
  ctpSysUserAuthFailUserName SnmpAdminString
  ctpSysUserAuthFailAccessProtocol CtpSystemAccessProtocol
  ctpSysUserAuthFailTimeStamp TimeStamp

Defined Values

ciscoTelepresenceMIB 1.3.6.1.4.1.9.9.643
The MIB module defines the managed objects for a Telepresence system. Telepresence refers to a set of technologies which allow a person to feel as if they were present, to give the appearance that they were present, or to have an effect, at a location other than their true location. A complete Telepresence system includes one or more Telepresence CODECS and peripherals such as display, camera, speaker, microphone and presentation device. Peripherals are attached directly to a Telepresence CODEC via an interface. Some peripherals may have more than one interface to transmit audio and/or video data and provide a configuration and/or control access.
MODULE-IDENTITY    

ciscoTelepresenceMIBNotifs 1.3.6.1.4.1.9.9.643.0
OBJECT IDENTIFIER    

ciscoTelepresenceMIBObjects 1.3.6.1.4.1.9.9.643.1
OBJECT IDENTIFIER    

ciscoTelepresenceMIBConform 1.3.6.1.4.1.9.9.643.2
OBJECT IDENTIFIER    

ctpObjects 1.3.6.1.4.1.9.9.643.1.1
OBJECT IDENTIFIER    

ctpPeripheralStatusObjects 1.3.6.1.4.1.9.9.643.1.2
OBJECT IDENTIFIER    

ctpEventHistory 1.3.6.1.4.1.9.9.643.1.3
OBJECT IDENTIFIER    

ctpPeripheralErrorNotifyEnable 1.3.6.1.4.1.9.9.643.1.1.1
This object controls generation of ctpPeripheralErrorNotification. When the object is 'true(1)', generation of ctpPeripheralErrorNotification is enabled. When the object is 'false(2)', generation of ctpPeripheralErrorNotification is disabled. ctpPeripheralErrorNotifyEnable object is superseded by ctpPeriStatusChangeNotifyEnable.
Status: deprecated Access: read-write
OBJECT-TYPE    
  TruthValue  

ctpSysUserAuthFailNotifyEnable 1.3.6.1.4.1.9.9.643.1.1.2
This object controls generation of ctpSysUserAuthFailNotification. When the object is 'true(1)', generation of ctpSysUserAuthFailNotification is enabled. When the object is 'false(2)', generation of ctpSysUserAuthFailNotification is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ctpSystemReset 1.3.6.1.4.1.9.9.643.1.1.3
This object is used to reset or restart a Telepresence system.
Status: current Access: read-write
OBJECT-TYPE    
  CtpSystemResetMode  

ctpPeriStatusChangeNotifyEnable 1.3.6.1.4.1.9.9.643.1.1.4
This object controls generation of ctpPeriStatusChangeNotification. When the object is 'true(1)', generation of ctpPeriStatusChangeNotification is enabled. When the object is 'false(2)', generation of ctpPeriStatusChangeNotification is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ctpVlanId 1.3.6.1.4.1.9.9.643.1.1.5
This object specifies the Telepresence system VLAN ID.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

ctpDefaultGatewayAddrType 1.3.6.1.4.1.9.9.643.1.1.6
This object specifies the type of address contained in the corresponding instance of ctpDefaultGateway.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

ctpDefaultGateway 1.3.6.1.4.1.9.9.643.1.1.7
This object specifies the Telepresence system default gateway.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

ctpPeripheralStatusTable 1.3.6.1.4.1.9.9.643.1.2.1
The table contains system peripheral information. An entry in this table has a corresponding entry, INDEX-ed by the same value of ctpPeripheralIndex, in the table relevant to the type of interface: ctpEtherPeripheralStatusTable for Ethernet, ctpHDMIPeripheralStatusTable for HDMI or ctpDVIPeripheralStatusTable for DVI.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtpPeripheralStatusEntry

ctpPeripheralStatusEntry 1.3.6.1.4.1.9.9.643.1.2.1.1
An entry contains information about one peripheral which is configured or detected by a Telepresence system.
Status: current Access: not-accessible
OBJECT-TYPE    
  CtpPeripheralStatusEntry  

ctpPeripheralIndex 1.3.6.1.4.1.9.9.643.1.2.1.1.1
This object specifies a unique index for a peripheral which is attached to a Telepresence system.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

ctpPeripheralDescription 1.3.6.1.4.1.9.9.643.1.2.1.1.2
This object specifies a description of the attached peripheral. Peripheral description may be the peripheral type, model and/or version information or a peripheral signal description.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

ctpPeripheralStatus 1.3.6.1.4.1.9.9.643.1.2.1.1.3
This object specifies a peripheral status.
Status: current Access: read-only
OBJECT-TYPE    
  CtpPeripheralStatusCode  

ctpPeripheralDeviceCategory 1.3.6.1.4.1.9.9.643.1.2.1.1.4
This object specifies a peripheral category of a device.
Status: current Access: read-only
OBJECT-TYPE    
  CtpPeripheralDeviceCategoryCode  

ctpPeripheralDeviceNumber 1.3.6.1.4.1.9.9.643.1.2.1.1.5
This object specifies a device number for a peripheral. Device number is unique within the same peripheral device category.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ctpEtherPeripheralStatusTable 1.3.6.1.4.1.9.9.643.1.2.2
The table contains information about all peripherals connected to the system via Ethernet port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtpEtherPeripheralStatusEntry

ctpEtherPeripheralStatusEntry 1.3.6.1.4.1.9.9.643.1.2.2.1
An entry contains information about one peripheral attached to the Telepresence system via Ethernet.
Status: current Access: not-accessible
OBJECT-TYPE    
  CtpEtherPeripheralStatusEntry  

ctpEtherPeripheralIndex 1.3.6.1.4.1.9.9.643.1.2.2.1.1
This object specifies a unique number for a peripheral Ethernet interface. If no peripheral has more than one Ethernet interface, this object will have value '1'.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

ctpEtherPeripheralIfIndex 1.3.6.1.4.1.9.9.643.1.2.2.1.2
The object specifies an index value that uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IF-MIB's ifIndex. If this entry doesn't have corresponding ifIndex, then this value will have value '0'.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

ctpEtherPeripheralAddrType 1.3.6.1.4.1.9.9.643.1.2.2.1.3
This object specifies the type of address contained in the corresponding instance of ctpEtherPeripheralAddr.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

ctpEtherPeripheralAddr 1.3.6.1.4.1.9.9.643.1.2.2.1.4
This object specifies the address of the attached peripheral in the format given by the corresponding instance of ctpEtherPeripheralAddrType.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

ctpEtherPeripheralStatus 1.3.6.1.4.1.9.9.643.1.2.2.1.5
This object specifies attached peripheral status retrieved via Ethernet port.
Status: current Access: read-only
OBJECT-TYPE    
  CtpPeripheralStatusCode  

ctpHDMIPeripheralStatusTable 1.3.6.1.4.1.9.9.643.1.2.3
The table contains information about all peripherals connected to the system via HDMI.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtpHDMIPeripheralStatusEntry

ctpHDMIPeripheralStatusEntry 1.3.6.1.4.1.9.9.643.1.2.3.1
An entry contains information about one Telepresence HDMI peripheral.
Status: current Access: not-accessible
OBJECT-TYPE    
  CtpHDMIPeripheralStatusEntry  

ctpHDMIPeripheralIndex 1.3.6.1.4.1.9.9.643.1.2.3.1.1
This object specifies a unique number for a peripheral HDMI. If no peripheral has more than one HDMI, this object will have value '1'.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

ctpHDMIPeripheralCableStatus 1.3.6.1.4.1.9.9.643.1.2.3.1.2
This object specifies cable status of an attached peripheral. This object is set to 'loose' if system detects cable is 'unplugged' but power is 'on'.
Status: current Access: read-only
OBJECT-TYPE    
  CtpPeripheralCableCode  

ctpHDMIPeripheralPowerStatus 1.3.6.1.4.1.9.9.643.1.2.3.1.3
This object specifies power status of an attached peripheral. This object is set to 'unknown' if system detects cable is 'unplugged'.
Status: current Access: read-only
OBJECT-TYPE    
  CtpPeripheralPowerCode  

ctpDVIPeripheralStatusTable 1.3.6.1.4.1.9.9.643.1.2.4
The table contains information about all peripherals connected to the system via DVI.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtpDVIPeripheralStatusEntry

ctpDVIPeripheralStatusEntry 1.3.6.1.4.1.9.9.643.1.2.4.1
An entry contains information about one peripheral attached to the Telepresence system via DVI.
Status: current Access: not-accessible
OBJECT-TYPE    
  CtpDVIPeripheralStatusEntry  

ctpDVIPeripheralIndex 1.3.6.1.4.1.9.9.643.1.2.4.1.1
This object specifies a unique number for a peripheral DVI. If no peripheral has more than one DVI, this object will have value '1'. Note that some Telepresence systems have no DVI port and some Telepresence systems have only one DVI port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

ctpDVIPeripheralCableStatus 1.3.6.1.4.1.9.9.643.1.2.4.1.2
This object specifies attached device cable status reported by DVI.
Status: current Access: read-only
OBJECT-TYPE    
  CtpPeripheralCableCode  

ctpRS232PeripheralStatusTable 1.3.6.1.4.1.9.9.643.1.2.5
The table contains information about all peripherals connected to the system via RS-232.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtpRS232PeripheralStatusEntry

ctpRS232PeripheralStatusEntry 1.3.6.1.4.1.9.9.643.1.2.5.1
An entry contains information about one peripheral attached to the Telepresence system via RS-232.
Status: current Access: not-accessible
OBJECT-TYPE    
  CtpRS232PeripheralStatusEntry  

ctpRS232PeripheralIndex 1.3.6.1.4.1.9.9.643.1.2.5.1.1
This object specifies a unique number for a peripheral RS-232. If no peripheral has more than one RS-232, this object will have value '1'. Note that some Telepresence systems have no RS-232 port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

ctpRS232PortIndex 1.3.6.1.4.1.9.9.643.1.2.5.1.2
The object specifies an index value that uniquely identifies the RS-232 port to which this entry is applicable. Its value is the same as RS-232-MIB's rs232PortIndex for the port. If RS-232-MIB is not supported by the agent, then this value will have value '0'.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

ctpRS232PeripheralConnStatus 1.3.6.1.4.1.9.9.643.1.2.5.1.3
This object specifies peripheral which is connected via RS232. When the object is 'connected(1)', peripheral connection via RS232 is working properly. When the object is 'unknown(2)', peripheral connection via RS232 is not working properly. It may due to device problem or connection problem.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER connected(1), unknown(2)  

ctpPeripheralAttributeTable 1.3.6.1.4.1.9.9.643.1.2.6
The table contains information about attributes for the peripherals which are connected to the system. Peripheral attribute may specify peripheral's component information, for example, an entry may specify lifetime of a lamp on a presentation device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtpPeripheralAttributeEntry

ctpPeripheralAttributeEntry 1.3.6.1.4.1.9.9.643.1.2.6.1
An entry contains information about one peripheral attribute related to the peripheral specified by ctpPeripheralIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  CtpPeripheralAttributeEntry  

ctpPeripheralAttributeIndex 1.3.6.1.4.1.9.9.643.1.2.6.1.1
This object specifies a unique number for a peripheral attribute. If no peripheral has more than one attribute, this object will have value '1'.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

ctpPeripheralAttributeDescr 1.3.6.1.4.1.9.9.643.1.2.6.1.2
This object specifies description of a attribute. The supported attributes are lampOperTime(1) -- indicate the lamp operating time of a peripheral lampState(2) -- indicate the lamp state powerSwitchState(3) -- indicate the power on/off state of a peripheral Note that not all peripheral contains all the supported attributes. Agent reports whatever is available.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER lampOperTime(1), lampState(2), powerSwitchState(3)  

ctpPeripheralAttributeValue 1.3.6.1.4.1.9.9.643.1.2.6.1.3
This object specifies value of the attribute corresponding to ctpPeripheralAttributeDescr. The possible value of the supported attributes is listed as the following: Attribute Unit SYNTAX ----------------------------------------------------------- lampOperTime hours Unsigned32(0..4294967295) lampState INTEGER { on(1), off(2), failure(3), unknown(4) } powerSwitchState INTEGER { on(1), off(2), unknown(3) }
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ctpUSBPeripheralStatusTable 1.3.6.1.4.1.9.9.643.1.2.7
This table contains information about all the peripherals connected to the system via USB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtpUSBPeripheralStatusEntry

ctpUSBPeripheralStatusEntry 1.3.6.1.4.1.9.9.643.1.2.7.1
An entry drescribes a peripheral connected to the Telepresence system through USB.
Status: current Access: not-accessible
OBJECT-TYPE    
  CtpUSBPeripheralStatusEntry  

ctpUSBPeripheralIndex 1.3.6.1.4.1.9.9.643.1.2.7.1.1
This object indicates an arbitrary positive, integer-value that uniquely identifies the USB peripheral.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

ctpUSBPeripheralCableStatus 1.3.6.1.4.1.9.9.643.1.2.7.1.2
This object indicates the status of the cable attaching the USB peripheral.
Status: current Access: read-only
OBJECT-TYPE    
  CtpPeripheralCableCode  

ctpUSBPeripheralPowerStatus 1.3.6.1.4.1.9.9.643.1.2.7.1.3
This object indicates the source of power for the attached USB peripheral: 'unknown' - The source of power is unknown. 'self' - The USB peripheral is externally powered. 'bus' - The USB peripheral is powered by the USB bus. 'both' - The USB peripheral can be powered by both the USB bus or self
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), self(2), bus(3), both(4)  

ctpUSBPeripheralPortType 1.3.6.1.4.1.9.9.643.1.2.7.1.4
This object indicates the type of device connected to the USB port: 'host' - no device os connected to the port 'device' - a usb device is connected to the port 'hub' - a usb hub is connected to the port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER host(1), device(2), hub(3)  

ctpUSBPeripheralPortRate 1.3.6.1.4.1.9.9.643.1.2.7.1.5
This object indicates the current operational rate of the USB peripheral: 'unknown' - The USB port rate is unknown 'low' - The USB port rate is at 1.5 Mbps. 'full' - The USB port rate is at 12 Mbps. 'high' - The USB port rate is at 480 Mbps.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER low(1), full(2), high(3)  

ctp802dot11PeripheralStatusTable 1.3.6.1.4.1.9.9.643.1.2.8
The table contains information about all peripherals connected to the system via 802dot11.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Ctp802dot11PeripheralStatusEntry

ctp802dot11PeripheralStatusEntry 1.3.6.1.4.1.9.9.643.1.2.8.1
An entry describes one Telepresence 802dot11 peripheral.
Status: current Access: not-accessible
OBJECT-TYPE    
  Ctp802dot11PeripheralStatusEntry  

ctp802dot11PeripheralIndex 1.3.6.1.4.1.9.9.643.1.2.8.1.1
This object indicates an arbitrary positive, integer-value that uniquely identifies the IEEE 802.11 peripheral.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

ctp802dot11PeripheralIfIndex 1.3.6.1.4.1.9.9.643.1.2.8.1.2
This object indicates an index value that uniquely identifies the interface to which this entry is applicable. If this entry doesn't have corresponding ifIndex, then this value will have value '0'.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

ctp802dot11PeripheralAddrType 1.3.6.1.4.1.9.9.643.1.2.8.1.3
This object indicates the type of address indicated by the corresponding instance of ctp802dot11PeripheralAddr.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

ctp802dot11PeripheralAddr 1.3.6.1.4.1.9.9.643.1.2.8.1.4
This object indicates the address of the attached peripheral in the format indicated by the corresponding instance of ctp802dot11PeripheralAddrType.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

ctp802dot11PeripheralLinkStrength 1.3.6.1.4.1.9.9.643.1.2.8.1.5
This object indicates the link strength of an IEEE 802.11 link for a peripheral. A return value of 0 indicates the link is not connected. A return value between 1 - 5 indicates the strength of the link, with 1 being the weakest and 5 being the strongest.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ctp802dot11PeripheralLinkStatus 1.3.6.1.4.1.9.9.643.1.2.8.1.6
This object indicates the link status of the attached peripheral via IEEE 802.11 link.
Status: current Access: read-only
OBJECT-TYPE    
  CtpPeripheralCableCode  

ctpDPPeripheralStatusTable 1.3.6.1.4.1.9.9.643.1.2.9
The table contains information about all peripherals connected to the system via DP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtpDPPeripheralStatusEntry

ctpDPPeripheralStatusEntry 1.3.6.1.4.1.9.9.643.1.2.9.1
An entry contains information about one Telepresence DP peripheral.
Status: current Access: not-accessible
OBJECT-TYPE    
  CtpDPPeripheralStatusEntry  

ctpDPPeripheralIndex 1.3.6.1.4.1.9.9.643.1.2.9.1.1
This object indicates a unique number for a peripheral DP. If no peripheral has more than one DP, this object will have value '1'.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

ctpDPPeripheralCableStatus 1.3.6.1.4.1.9.9.643.1.2.9.1.2
This object indicates the cable status of a peripheral which is attached to the system via Display Port interface. This object returns 'loose' if system detects cable is 'unplugged' but power is 'on'.
Status: current Access: read-only
OBJECT-TYPE    
  CtpPeripheralCableCode  

ctpDPPeripheralPowerStatus 1.3.6.1.4.1.9.9.643.1.2.9.1.3
This object indicates the power status of a peripheral which is attached to the system via Display Port interface. This object returns 'unknown' if system detects cable is 'unplugged'.
Status: current Access: read-only
OBJECT-TYPE    
  CtpPeripheralPowerCode  

ctpPeripheralErrorHistTableSize 1.3.6.1.4.1.9.9.643.1.3.1
This object specifies the maximum number of entries that the ctpPeripheralErrorHistTable can contain. When the capacity of the ctpPeripheralErrorHistTable has reached the value specified by this object, then the agent deletes the oldest entity in order to accommodate the new entry. A value of '0' prevents any history from being retained. Some agents restrict the value of this object to be less than 500.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..500  

ctpPeripheralErrorHistLastIndex 1.3.6.1.4.1.9.9.643.1.3.2
This object specifies the value of the ctpPeripheralErrorHistIndex object corresponding to the last entry added to the table by the agent. If the management application uses the notifications defined by this module, then it can poll this object to determine whether it has missed a notification sent by the agent.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

ctpPeripheralErrorHistoryTable 1.3.6.1.4.1.9.9.643.1.3.3
This table contains a history of the detected peripheral status changes. After a management agent restart, when sysUpTime is reset to zero, this table records all notifications until such time as it becomes full. Thereafter, it remains full by retaining the number of most recent notifications specified in ctpPeripheralErrorHistTableSize.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtpPeripheralErrorHistoryEntry

ctpPeripheralErrorHistoryEntry 1.3.6.1.4.1.9.9.643.1.3.3.1
An entry contains information about a Telepresence peripheral status changes.
Status: current Access: not-accessible
OBJECT-TYPE    
  CtpPeripheralErrorHistoryEntry  

ctpPeripheralErrorHistoryIndex 1.3.6.1.4.1.9.9.643.1.3.3.1.1
A unique non-zero integer value that identifies a CtpPeripheralErrorHistoryEntry in the table. The value of this index starts from '1' and monotonically increases for each peripheral error known to the agent. If the value of this object is '4294967295', the agent will use '1' as the value of the next detected peripheral status change.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ctpPeripheralErrorIndex 1.3.6.1.4.1.9.9.643.1.3.3.1.2
The object specifies the value of ctpPeripheralIndex of a peripheral which is in error state. This object is deprecated in favor of ctpPeripheralErrorDeviceCategory and ctpPeripheralErrorDeviceNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ctpPeripheralErrorStatus 1.3.6.1.4.1.9.9.643.1.3.3.1.3
This object specifies the peripheral status after its status changed.
Status: current Access: read-only
OBJECT-TYPE    
  CtpPeripheralStatusCode  

ctpPeripheralErrorTimeStamp 1.3.6.1.4.1.9.9.643.1.3.3.1.4
This object specifies the value of the sysUpTime object at the time the notification was generated.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

ctpPeripheralErrorDeviceCategory 1.3.6.1.4.1.9.9.643.1.3.3.1.5
The object specifies peripheral device category after its status changed.
Status: current Access: read-only
OBJECT-TYPE    
  CtpPeripheralDeviceCategoryCode  

ctpPeripheralErrorDeviceNumber 1.3.6.1.4.1.9.9.643.1.3.3.1.6
The object specifies peripheral device number after its status changed. Device number is unique within the same peripheral device category.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ctpSysUserAuthFailHistTableSize 1.3.6.1.4.1.9.9.643.1.3.4
This object specifies the number of entries that the ctpSysUserAuthFailHistTable can contain. When the capacity of the ctpSysUserAuthFailHistTable has reached the value specified by this object, then the agent deletes the oldest entity in order to accommodate the new entry. A value of '0' prevents any history from being retained. Some agents restrict the value of this object to be less than 500.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..500  

ctpSysUserAuthFailHistLastIndex 1.3.6.1.4.1.9.9.643.1.3.5
This object specifies the value of the ctpSysUserAuthFailHistIndex object corresponding to the last entry added to the table by the agent. If the management application uses the notifications defined by this module, then it can poll this object to determine whether it has missed a notification sent by the agent.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

ctpSysUserAuthFailHistoryTable 1.3.6.1.4.1.9.9.643.1.3.6
This table contains a history of detected user authentication failures. After a management agent restart, when sysUpTime is reset to zero, this table records all user authentication failure notifications until such time as it becomes full. Thereafter, it remains full by retaining the number of most recent notifications specified in ctpSysUserAuthFailHistTableSize.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtpSysUserAuthFailHistoryEntry

ctpSysUserAuthFailHistoryEntry 1.3.6.1.4.1.9.9.643.1.3.6.1
An entry contains information about a Telepresence system user authentication failure.
Status: current Access: not-accessible
OBJECT-TYPE    
  CtpSysUserAuthFailHistoryEntry  

ctpSysUserAuthFailHistoryIndex 1.3.6.1.4.1.9.9.643.1.3.6.1.1
A unique non-zero integer value that identifies a CtpSysUserAuthFailHistoryEntry in the table. The value of this index starts from '1' and monotonically increases for each system authentication failure event known to the agent. If the value of this object is '4294967295', the agent will use '1' as the value of the next user authentication failure event.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ctpSysUserAuthFailSourceAddrType 1.3.6.1.4.1.9.9.643.1.3.6.1.2
The object specifies the type of address contained in the corresponding instance of ctpSysUserAuthFailSourceAddr.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

ctpSysUserAuthFailSourceAddr 1.3.6.1.4.1.9.9.643.1.3.6.1.3
The object specifies the source address when the user authentication failure occurred, in the format given by the corresponding instance of ctpSysUserAuthFailSourceAddrType.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

ctpSysUserAuthFailSourcePort 1.3.6.1.4.1.9.9.643.1.3.6.1.4
The object specifies the source TCP/UDP port number when a user authentication failure occurred.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ctpSysUserAuthFailUserName 1.3.6.1.4.1.9.9.643.1.3.6.1.5
The object specifies the user name which was used to gain system access when authentication failure occurred.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

ctpSysUserAuthFailAccessProtocol 1.3.6.1.4.1.9.9.643.1.3.6.1.6
This object specifies the access protocol when a user authentication failure occurred.
Status: current Access: read-only
OBJECT-TYPE    
  CtpSystemAccessProtocol  

ctpSysUserAuthFailTimeStamp 1.3.6.1.4.1.9.9.643.1.3.6.1.7
This object specifies the value of the sysUpTime object at the time the notification was generated.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

ctpPeripheralErrorNotification 1.3.6.1.4.1.9.9.643.0.1
This notification is sent when a peripheral error is detected. This notification is deprecated in favor of ctpPeriStatusChangeNotification. ctpPeripheralErrorNotification object is superseded by ctpPeriStatusChangeNotification.
Status: deprecated Access: read-only
NOTIFICATION-TYPE    

ctpSysUserAuthFailNotification 1.3.6.1.4.1.9.9.643.0.2
This notification is sent when a user authentication failure via a Telepresence supported access protocol is detected.
Status: current Access: read-only
NOTIFICATION-TYPE    

ctpPeriStatusChangeNotification 1.3.6.1.4.1.9.9.643.0.3
This notification is sent when a peripheral status is changed.
Status: current Access: read-only
NOTIFICATION-TYPE    

ciscoTelepresenceCompliances 1.3.6.1.4.1.9.9.643.2.1
OBJECT IDENTIFIER    

ciscoTelepresenceMIBGroups 1.3.6.1.4.1.9.9.643.2.2
OBJECT IDENTIFIER    

ciscoTelepresenceCompliance 1.3.6.1.4.1.9.9.643.2.1.1
The compliance statement for entities which implement the Cisco Telepresence MIB.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoTelepresenceComplianceR01 1.3.6.1.4.1.9.9.643.2.1.2
The compliance statement for entities which implement the Cisco Telepresence MIB.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoTelepresenceComplianceR02 1.3.6.1.4.1.9.9.643.2.1.3
The compliance statement for entities which implement the Cisco Telepresence MIB.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoTelepresenceComplianceR03 1.3.6.1.4.1.9.9.643.2.1.4
The compliance statement for entities which implement the Cisco Telepresence MIB.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoTelepresenceComplianceR04 1.3.6.1.4.1.9.9.643.2.1.5
The compliance statement for entities which implement the Cisco Telepresence MIB.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoTelepresenceComplianceR05 1.3.6.1.4.1.9.9.643.2.1.6
The compliance statement for entities which implement the Cisco Telepresence MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

ciscoTpConfigurationGroup 1.3.6.1.4.1.9.9.643.2.2.1
A collection of objects providing the notification configuration and system reset. ciscoTpConfigurationGroup object is superseded by ciscoTpConfigurationGroupR01.
Status: deprecated Access: read-only
OBJECT-GROUP    

ciscoTpPeripheralStatusGroup 1.3.6.1.4.1.9.9.643.2.2.2
A collection of objects providing the Telepresence peripheral information. ciscoTpPeripheralStatusGroup object is superseded by ciscoTpPeripheralStatusGroupR01.
Status: deprecated Access: read-only
OBJECT-GROUP    

ciscoTpEventHistoryGroup 1.3.6.1.4.1.9.9.643.2.2.3
A collection of managed objects providing notification event history information. ciscoTpEventHistoryGroup object is superseded by ciscoTpEventHistoryGroupR01.
Status: deprecated Access: read-only
OBJECT-GROUP    

ciscoTpNotificationGroup 1.3.6.1.4.1.9.9.643.2.2.4
A collection of Telepresence system notifications. ciscoTpNotificationGroup object is superseded by ciscoTpNotificationGroupR01.
Status: deprecated Access: read-only
NOTIFICATION-GROUP    

ciscoTpRS232PeripheralStatusGroup 1.3.6.1.4.1.9.9.643.2.2.5
A collection of objects providing the information about Telepresence peripheral which is connected via RS232.
Status: current Access: read-only
OBJECT-GROUP    

ciscoTpPeripheralAttributeGroup 1.3.6.1.4.1.9.9.643.2.2.6
A collection of managed objects providing peripheral attribute information.
Status: current Access: read-only
OBJECT-GROUP    

ciscoTpPeripheralStatusGroupR01 1.3.6.1.4.1.9.9.643.2.2.7
A collection of objects providing the Telepresence peripheral information. ciscoTpPeripheralStatusGroupR01 object is superseded by ciscoTpPeripheralStatusGroupR02.
Status: deprecated Access: read-only
OBJECT-GROUP    

ciscoTpEventHistoryGroupR01 1.3.6.1.4.1.9.9.643.2.2.8
A collection of managed objects providing notification event history information.
Status: current Access: read-only
OBJECT-GROUP    

ciscoTpNotificationGroupR01 1.3.6.1.4.1.9.9.643.2.2.9
A collection of Telepresence system notifications.
Status: current Access: read-only
NOTIFICATION-GROUP    

ciscoTpConfigurationGroupR01 1.3.6.1.4.1.9.9.643.2.2.10
A collection of objects providing the notification configuration and system reset.
Status: current Access: read-only
OBJECT-GROUP    

ciscoTpPeripheralStatusGroupR02 1.3.6.1.4.1.9.9.643.2.2.11
A collection of objects providing the Telepresence peripheral information.
Status: current Access: read-only
OBJECT-GROUP    

ciscoTpConfigurationGroupR02 1.3.6.1.4.1.9.9.643.2.2.12
A collection of objects providing network configurations.
Status: current Access: read-only
OBJECT-GROUP    

ciscoTpDPPeripheralStatusGroup 1.3.6.1.4.1.9.9.643.2.2.13
A collection of objects providing the information about Telepresence peripheral which is connected via Display Port.
Status: current Access: read-only
OBJECT-GROUP