CISCO-TAP2-MIB
File:
CISCO-TAP2-MIB.mib (39763 bytes)
Imported modules
Imported symbols
Defined Types
| CTap2StreamEntry |
|
| SEQUENCE |
|
|
|
| |
cTap2StreamIndex |
INTEGER |
|
| |
cTap2StreamType |
INTEGER |
|
| |
cTap2StreamInterceptEnable |
TruthValue |
|
| |
cTap2StreamInterceptedPackets |
Counter |
|
| |
cTap2StreamInterceptDrops |
Counter |
|
| |
cTap2StreamStatus |
RowStatus |
|
| |
cTap2StreamInterceptedHCPackets |
Counter |
|
| |
cTap2StreamInterceptHCDrops |
Counter |
|
| CTap2DebugEntry |
|
| SEQUENCE |
|
|
|
| |
cTap2DebugIndex |
INTEGER |
|
| |
cTap2DebugMediationId |
Gauge |
|
| |
cTap2DebugStreamId |
Gauge |
|
| |
cTap2DebugMessage |
SnmpAdminString |
|
| |
cTap2DebugStatus |
RowStatus |
|
| CTap2DebugUserEntry |
|
| SEQUENCE |
|
|
|
| |
cTap2DebugUserName |
SnmpAdminString |
|
| |
cTap2DebugUserTimeout |
DateAndTime |
|
| |
cTap2DebugUserStorageType |
StorageType |
|
| |
cTap2DebugUserStatus |
RowStatus |
|
Defined Values
| cTap2MediationEntry |
1.3.6.1.4.1.9.9.399.1.1.2.1 |
| The entry describes a single session maintained with an
application on a Mediation Device. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
CTap2MediationEntry |
|
|
| cTap2MediationContentId |
1.3.6.1.4.1.9.9.399.1.1.2.1.1 |
| cTap2MediationContentId is a session identifier, from the
intercept application's perspective, and a content identifier
from the Mediation Device's perspective. The Mediation Device
is responsible for making sure these are unique, although the
SNMP RowStatus row creation process will help by not allowing
it to create conflicting entries. Before creating a new entry,
a value for this variable may be obtained by reading
cTap2MediationNewIndex to reduce the probability of a value
collision. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..2147483647 |
|
| cTap2StreamTable |
1.3.6.1.4.1.9.9.399.1.2.1 |
| The Intercept Stream Table lists the traffic streams to be
intercepted. The same data stream may be required by multiple
taps, and one might assume that often the intercepted stream
is a small subset of the traffic that could be intercepted.
The Table consists of generic fields that are independent
of the type of intercept. It contains type of the specific
filter which is defined in an extension MIB and counters to
account for packets intercepted or dropped by the attached
filter specification.
Note that the Mediation Device must make sure there is
only one type of specific filter created with the same
indices as that of a row in this table, otherwise the
later creations will fail. For example, if there is a
row in this table with index 1.2, there can be a
corresponding row with the same index either in
citapStreamTable, c8tapStreamTable or cuctTapStreamTable,
but not all.
The first index indicates which Mediation Device the
intercepted traffic will be diverted to. The second index
permits multiple classifiers to be used together.
Entries are added to this table via cTap2StreamStatus in
accordance with the RowStatus convention. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
CTap2StreamEntry |
|
| cTap2StreamEntry |
1.3.6.1.4.1.9.9.399.1.2.1.1 |
| A stream entry indicates a single data stream to be
intercepted to a Mediation Device. Many selected data
streams may go to the same application interface, and many
application interfaces are supported. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
CTap2StreamEntry |
|
|
| cTap2StreamIndex |
1.3.6.1.4.1.9.9.399.1.2.1.1.1 |
| The index of the stream itself. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..2147483647 |
|
| cTap2StreamType |
1.3.6.1.4.1.9.9.399.1.2.1.1.2 |
| Identifies the type of intercept filter associated to this
generic stream. The following types of streams are supported:
ip: The specific filter is an IP filter
with same indices as that of this
table. The exact filter is a row in
citapStreamTable of CISCO-IP-TAP-MIB.
mac: The specific filter is a MAC filter
with same indices as that of this table.
The exact filter is a row in
c8tapStreamTable of CISCO-802-TAP-MIB.
userConnecton: The specific filter is a user connection
filter with same indices as that of
this table. The exact filter is a row
in cuctTapStreamTable of
CISCO-USER-CONNECTION-TAP-MIB.
msPdsn: The specific filter is a Mobile Sub
connection filter with same indices as
that of this table. The exact filter
is a row in ccptapStreamTable of
CISCO-CDMA-PDSN-TAP-MIB.
mobility: The specific filter is a Mobile
Subscriber connection filter with same
indices as that of this table. The exact
filter is a row in cmtapStreamTable of
CISCO-MOBILITY-TAP-MIB. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
ip(1), mac(2), userConnection(3), msPdsn(4), mobility(5) |
|
| cTap2StreamInterceptEnable |
1.3.6.1.4.1.9.9.399.1.2.1.1.3 |
| If 'true', the tap should intercept matching traffic. The
value for this object should be set to 'true' only after an
additional filter specification has been attached to this
stream. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| cTap2StreamInterceptedPackets |
1.3.6.1.4.1.9.9.399.1.2.1.1.4 |
| The number of packets matching this data stream specification
that have been intercepted. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|
| cTap2StreamInterceptDrops |
1.3.6.1.4.1.9.9.399.1.2.1.1.5 |
| The number of packets matching this data stream specification
that, having been intercepted, were dropped in the lawful
intercept process. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|
| cTap2StreamStatus |
1.3.6.1.4.1.9.9.399.1.2.1.1.6 |
| The status of this conceptual row. This object manages
creation, modification, and deletion of rows in this table.
cTap2StreamInterceptEnable may be modified any time even the
value of this entry rowStatus object is 'active'. When other
rows must be changed, cTap2StreamStatus must be first set to
'notInService'. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| cTap2StreamInterceptedHCPackets |
1.3.6.1.4.1.9.9.399.1.2.1.1.7 |
| The number of packets matching this data stream specification
that have been intercepted. This object is a 64-bit version of
cTap2StreamInterceptedPackets. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|
| cTap2StreamInterceptHCDrops |
1.3.6.1.4.1.9.9.399.1.2.1.1.8 |
| The number of packets matching this data stream specification
that, having been intercepted, were dropped in the lawful
intercept process. This object is a 64-bit version of
cTap2StreamInterceptDrops. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|
| cTap2DebugAge |
1.3.6.1.4.1.9.9.399.1.3.1 |
| This object contains the duration in minutes for which an
entry in cTap2DebugTable is maintained by the implementing
device after which the entry is deleted. The management
station also has the option of deleting the entry itself
by setting cTap2DebugStatus. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..2147483647 |
|
| cTap2DebugMaxEntries |
1.3.6.1.4.1.9.9.399.1.3.2 |
| This object contains the maximum number of debug messages
maintained by the implementing device at a time. If this
limit is crossed, most recent message will replace the
least recent message. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..2147483647 |
|
| cTap2DebugTable |
1.3.6.1.4.1.9.9.399.1.3.3 |
| A table that contains Lawful Intercept debug messages
generated by the implementing device. This table is used
by ciscoTap2MediationDebug and ciscoTap2StreamDebug
notifications.
An entry in this table contains a debug message which is
regarding either a Mediation Device or a intercept stream
created by a Mediation Device. The Mediation device is
identified by cTap2DebugMediationId whose value is
that of cTap2MediationContentId of cTapMediationEntry.
The stream is identified by cTap2DebugMediationId and
cTap2DebugStreamId whose values are that of
cTap2MediationContentId and cTap2StreamIndex of
the corresponding cTap2StreamEntry.
Note that cTap2DebugStreamId may be zero for an entry,
in which case the debug message is regarding a Medation
Device.
Entries are added to this table via cTap2DebugStatus in
accordance with the RowStatus convention. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
CTap2DebugEntry |
|
| cTap2DebugEntry |
1.3.6.1.4.1.9.9.399.1.3.3.1 |
| A list of the debug messages. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
CTap2DebugEntry |
|
|
| cTap2DebugIndex |
1.3.6.1.4.1.9.9.399.1.3.3.1.1 |
| Index to the debug table. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..2147483647 |
|
| cTap2DebugStreamId |
1.3.6.1.4.1.9.9.399.1.3.3.1.3 |
| The value of this object is that of cTap2StreamIndex of an
entry in cTap2StreamTable. This object along with
cTap2DebugMediationId identifies an entry in cTap2StreamTable.
The value of this object may be zero, in which this debug
message is regarding a Mediation Device, but not a particular
stream. Note this object may contain a value for which an
entry in cTap2MediationTable does not exist. This happens
when creation of an entry in cTap2StreamTable fails. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge |
|
|
| cTap2DebugStatus |
1.3.6.1.4.1.9.9.399.1.3.3.1.5 |
| The status of this conceptual row. A row in this table is
created by the implementing device. A management station cannot
modify any of the objects in this row, except deleting the row
by setting this object to 'destroy'. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| cTap2DebugUserTable |
1.3.6.1.4.1.9.9.399.1.3.4 |
| The User Table lists information of all the users configured
in the system who are given permission by different Mediation
Devices to access Lawful Intercept CLIs.
This table will have dependancy on cTap2MediationTable. When
entry in cTap2MediationTable is deleted or moved to
'notInService', entries corresponding cTap2MediationContentId
in this table will be deleted. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
CTap2DebugUserEntry |
|
| cTap2DebugUserEntry |
1.3.6.1.4.1.9.9.399.1.3.4.1 |
| A conceptual row in the cTap2DebugUserTable. Each row
represents name of user on the router to whom Mediation Device
with CCCid represented by cTap2MediationContentId has given
access to Lawful Intercept commands and cTap2DebugUserTimeout
represents the time when the entry will expire. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
CTap2DebugUserEntry |
|
|
| cTap2DebugUserName |
1.3.6.1.4.1.9.9.399.1.3.4.1.1 |
| A human readable string representing the name of debug user
who will have access to Lawful Intercept commands. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SnmpAdminString |
Size(1..255) |
|
| cTap2DebugUserTimeout |
1.3.6.1.4.1.9.9.399.1.3.4.1.2 |
| This object specifies the time at which the row will be
removed from the table by the system. The value of this object
is only effective when the value of corresponding instance of
cTap2DebugUserStatus is 'active'. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DateAndTime |
|
|
| cTap2DebugUserStorageType |
1.3.6.1.4.1.9.9.399.1.3.4.1.3 |
| This object specifies the storage type of this conceptual row.
If it is set to 'nonVolatile', this entry can be saved into
non-volatile memory. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
StorageType |
|
|
| cTap2DebugUserStatus |
1.3.6.1.4.1.9.9.399.1.3.4.1.4 |
| The status of this conceptual row. This object manages
creation, modification, and deletion of rows in this table.
cTap2DebugUserTimeout may be modified any time even when the
value of this entry rowStatus object is 'active'. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| ciscoTap2MIBActive |
1 |
| This Notification is sent when an intercepting router or
switch is first capable of intercepting a packet corresponding
to a configured data stream. The value of the corresponding
cTap2StreamType which identifies the actual intercept stream
type is included in this notification.
This notification may be generated in conjunction with the
intercept application, which is designed to expect the
notification to be sent as reliably as possible, e.g., through
the use of a finite number of retransmissions until
acknowledged, as and when such mechanisms are available; for
example, with SNMPv3, this would be an InformRequest. Filter
installation can take a long period of time, during which call
progress may be delayed. |
| TRAP-TYPE |
|
|
|
| ciscoTap2StreamDebug |
4 |
| When there is intervention needed due to some events related
to entries configured in cTap2StreamTable, the device
notifies the manager of the event.
This notification may be generated in conjunction with the
intercept application, which is designed to expect the
notification to be sent as reliably as possible, e.g., through
the use of a finite number of retransmissions until
acknowledged, as and when such mechanisms are available; for
example, with SNMPv3, this would be an InformRequest. |
| TRAP-TYPE |
|
|
|
| ciscoTap2Switchover |
5 |
| This notification is sent when there is a redundant (standby)
route processor available on the intercepting device and the
current active processor is going down causing standby to
takeover. Note that this notification may be sent by the
intercepting device only when it had a chance to know before it
goes down.
Mediation device when received this notification should assume
that configured intercepts on the intercepting device no longer
exist, when the standby processor takes control. This means that
the Mediation device should again configure the intercepts. |
| TRAP-TYPE |
|
|
|