CISCO-POWER-ETHERNET-EXT-MIB

File: CISCO-POWER-ETHERNET-EXT-MIB.mib (56322 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
POWER-ETHERNET-MIB SNMP-FRAMEWORK-MIB CISCO-TC
CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
NOTIFICATION-TYPE MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP TEXTUAL-CONVENTION TruthValue
pethPsePortEntry pethMainPseGroupIndex pethPsePortGroupIndex
pethPsePortIndex SnmpAdminString EntPhysicalIndexOrZero
ciscoMgmt

Defined Types

CpeExtLldpPwrType  
The requested Data Terminal Equipment (DTE) Power via Media Dependent Interface (MDI) type based on Data Link Layer (DLL) power classification. In Data Link Layer power classification, the PSE and PD perform power negotiation using the Link Layer Discovery Protocol (LLDP) as soon as the data link is established. It has finer power resolution than the Physical Layer power classification and has the ability for the PSE and PD to participate in dynamic power allocation wherein allocated power to the PD may change one or more times during PD operation. 'type1Pd' - A PD that advertises a power draw less than or equal to 12.95 W (at the PD). 'type1Pse' - A PSE that is designed to support a Type 1 PD. 'type2Pd' - A PD that advertises a power draw greater than 12.95 W (at the PD). 'type2Pse - A PSE that is designed to support either a Type 1 or a Type 2 PD.
TEXTUAL-CONVENTION    
  INTEGER type1Pd(1), type1Pse(2), type2Pd(3), type2Pse(4)  

CpeExtLldpPwrSrc  
The power source of the PD or PSE port which implements the LLDP based Data Link Layer power classification. 'pseAndLocal' - A PD powered both locally and by a PSE. 'local' - A PD powered locally only. 'pse' - A PD powered by a PSE only. 'backupSrc' - A PSE powered by a backup power source. 'primarySrc' - A PSE powered by its primary power source. 'unknown' - A PD or PSE where the power source is unknown.
TEXTUAL-CONVENTION    
  INTEGER pseAndLocal(1), local(2), pse(3), backupSrc(4), primarySrc(5), unknown(6)  

CpeExtPwrPriority  
The power priority for the PD on the PSE port which implements the LLDP based Data Link Layer power classification. 'critical' - power priority is at critical level. 'high' - power priority is at high level. 'low' - power priority is at low level. 'unknown' - power priority level is unknown.
TEXTUAL-CONVENTION    
  INTEGER critical(1), high(2), low(3), unknown(4)  

CpeExtLldpPwrClassOrZero  
The power class of the PD or PSE port that implements the LLDP based Data Link Layer power classification 'unknown' - power classification of the powered devices is unknown. 'class0' - power classification of the powered devices is class 0 in IEEE specifications. 'class1' - power classification of the powered devices is class 1 in IEEE specifications. 'class2' - power classification of the powered devices is class 2 in IEEE specifications. 'class3' - power classification of the powered devices is class 3 in IEEE specifications. 'class4' - power classification of the powered devices is class 4 in IEEE specifications.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), class0(1), class1(2), class2(3), class3(4), class4(5)  

CpeExtPsePortEntry  
SEQUENCE    
  cpeExtPsePortEnable INTEGER
  cpeExtPsePortDiscoverMode INTEGER
  cpeExtPsePortDeviceDetected TruthValue
  cpeExtPsePortIeeePd TruthValue
  cpeExtPsePortAdditionalStatus BITS
  cpeExtPsePortPwrMax Unsigned32
  cpeExtPsePortPwrAllocated Unsigned32
  cpeExtPsePortPwrAvailable Unsigned32
  cpeExtPsePortPwrConsumption Unsigned32
  cpeExtPsePortMaxPwrDrawn Unsigned32
  cpeExtPsePortEntPhyIndex EntPhysicalIndexOrZero
  cpeExtPsePortPolicingCapable TruthValue
  cpeExtPsePortPolicingEnable INTEGER
  cpeExtPsePortPolicingAction INTEGER
  cpeExtPsePortPwrManAlloc Unsigned32
  cpeExtPsePortCapabilities BITS

CpeExtMainPseEntry  
SEQUENCE    
  cpeExtMainPseEntPhyIndex EntPhysicalIndexOrZero
  cpeExtMainPseDescr SnmpAdminString
  cpeExtMainPsePwrMonitorCapable TruthValue

CpeExtPdStatsEntry  
SEQUENCE    
  cpeExtPdStatsClass INTEGER
  cpeExtPdStatsDeviceCount Unsigned32

CpeExtPsePortLldpEntry  
SEQUENCE    
  cpeExtPsePortLldpPwrType CpeExtLldpPwrType
  cpeExtPsePortLldpPdPwrType CpeExtLldpPwrType
  cpeExtPsePortLldpPwrSrc CpeExtLldpPwrSrc
  cpeExtPsePortLldpPdPwrSrc CpeExtLldpPwrSrc
  cpeExtPsePortLldpPwrPriority CpeExtPwrPriority
  cpeExtPsePortLldpPdPwrPriority CpeExtPwrPriority
  cpeExtPsePortLldpPwrReq Unsigned32
  cpeExtPsePortLldpPdPwrReq Unsigned32
  cpeExtPsePortLldpPwrAlloc Unsigned32
  cpeExtPsePortLldpPdPwrAlloc Unsigned32
  cpeExtPsePortLldpPwrClass CpeExtLldpPwrClassOrZero
  cpeExtPsePortLldpPdPwrClass CpeExtLldpPwrClassOrZero
  cpeExtPsePortLldpPdPwrSupport BITS
  cpeExtPsePortLldpPdPwrPairsOrZero INTEGER

Defined Values

ciscoPowerEthernetExtMIB 4.9.402
A MIB module for extending the POWER-ETHERNET-MIB (RFC3621) to add objects which provide additional management information about Power Sourcing Equipment (PSE) not available in POWER-ETHERNET-MIB. Glossary Power Sourcing Equipment (PSE) These are devices supplying electrical power to other equipment. They are, for example, inline power switches, inline power daughterboards and power patch panels. Powered Device (PD) These are devices receiving their electrical power supply from Power Sourcing Equipment. They are, for example, IP telephones and wireless access points or bridges.
MODULE-IDENTITY    

cpeExtMIBNotifs 4.9.402.0
OBJECT IDENTIFIER    

cpeExtMIBObjects 4.9.402.1
OBJECT IDENTIFIER    

cpeExtMIBConformance 4.9.402.2
OBJECT IDENTIFIER    

cpeExtDefaultAllocation 4.9.402.1.1
This object indicates the default inline power allocation per port. This is a global configuration parameter that applies to all inline power capable ports in the system. The system must consider this object as well as the per port configuration object, cpeExtPsePortPwrMax, when determining how much power to allocate to a port. The system will use the lower of the two numbers.
OBJECT-TYPE    
  Unsigned32  

cpeExtPsePortTable 4.9.402.1.2
This table extends the POWER-ETHERNET-MIB pethPsePortTable for power Ethernet ports on a Powered Sourcing Equipment (PSE) device.
OBJECT-TYPE    
  SEQUENCE OF  
    CpeExtPsePortEntry

cpeExtPsePortEntry 4.9.402.1.2.1
A cpeExtPsePortEntry extends a corresponding pethPsePortTable entry. This entry displays and controls more characteristics of a power Ethernet port on a PSE device.
OBJECT-TYPE    
  CpeExtPsePortEntry  

cpeExtPsePortEnable 4.9.402.1.2.1.1
This object is an extension of the pethPsePortAdminEnable object from RFC3621. It allows the user to be more specific when enabling the PSE functions. The states, 'auto', 'static' and 'limit' correspond to a value of 'true' for the pethPsePortAdminEnable object. The state 'disable' corresponds to a value of 'false' for the pethPsePortAdminEnable object. Setting this value to 'auto' enables Powered Device discovery on the interface and the amount of power allocated depends on the Powered Device discovered. If pethPsePortAdminEnable was 'false' prior to this set operation, then it will become 'true'. Setting this value to 'static' will also enable Powered Device discovery. However, this is different from 'auto' in that the amount of power is pre-allocated based on the configuration on the Power Sourcing Equipment. If pethPsePortAdminEnable was 'false' prior to this set operation, then it will become 'true'. Setting this value to 'limit' enables Powered Device discovery on the interface. The amount of power allocated depends on the Powered Device discovered and the value of cpeExtPsePortPwrMax. The lower value will be used. If pethPsePortAdminEnable was 'false' prior to this set operation, then it will become 'true'. Setting this value to 'disable' disables the PSE functions. The pethPsePortAdminEnable object will adopt the value of 'false' if it was 'true' prior to this set operation. When setting the pethPsePortAdminEnable object to 'false' this object cpeExtPsePortEnable will adopt the value of 'disable'. If cpeExtPsePortPolicingCapable of the PSE port, or cpeExtMainPsePwrMonitorCapable of the PSE port's main group, has the value of 'false', this object can only be set to 'auto', 'static' or 'disable'. Otherwise, this object can be set to 'auto', 'static', 'limit' or 'disable'.
OBJECT-TYPE    
  INTEGER auto(1), static(2), limit(3), disable(4)  

cpeExtPsePortDiscoverMode 4.9.402.1.2.1.2
This object indicates the discover mode used by the system to discover the PD. A value of 'unknown' indicates that the discover mode on the interface is unknown. A value of 'off' indicates that discovery is disabled on the interface. A value of 'ieee' indicates that the discover mode on the interface is IEEE based. A value of 'cisco' indicates that the discover mode on the interface is Cisco based. A value of 'ieeeAndCisco' indicates that the discover mode on the interface is both IEEE and Cisco based.
OBJECT-TYPE    
  INTEGER unknown(1), off(2), ieee(3), cisco(4), ieeeAndCisco(5)  

cpeExtPsePortDeviceDetected 4.9.402.1.2.1.3
This object indicates if a Powered Device (PD) has been detected on the interface. A value of 'true' indicates that a PD has been detected on the interface. A value of 'false' indicates that no PD has been detected on the interface.
OBJECT-TYPE    
  TruthValue  

cpeExtPsePortIeeePd 4.9.402.1.2.1.4
This object indicates whether the Powered Device attached to the interface is an IEEE compliant Powered Device or not. A value of 'true' indicates the attached Powered Device is an IEEE compliant Powered Device. A value of 'false' indicates the attached Powered Device is not an IEEE compliant Powered Device. This also means that the value of the corresponding object from the pethPsePortTable, pethPsePortPowerClassifications is irrelevant.
OBJECT-TYPE    
  TruthValue  

cpeExtPsePortAdditionalStatus 4.9.402.1.2.1.5
This object is an extension of the pethPsePortDetectionStatus object from RFC3621 and provides additional status information. deny: When set, the PD attached to the interface is being denied power due to insufficient power resources on the Power Sourcing Equipment. overdraw: When set, the PD attached to the interface is being denied power because the PD is trying to consume more power than it has been configured to consume. overdrawLog: When set, the PD attached to the interface is trying to consume more power than it has been configured to consume, but is not being denied power.
OBJECT-TYPE    
  BITS deny(0), overdraw(1), overdrawLog(2)  

cpeExtPsePortPwrMax 4.9.402.1.2.1.6
This indicates the maximum amount of power that the PSE will make available to the PD connected to this interface.
OBJECT-TYPE    
  Unsigned32  

cpeExtPsePortPwrAllocated 4.9.402.1.2.1.7
This object indicates the amount of power allocated from the PSE for the PD.
OBJECT-TYPE    
  Unsigned32  

cpeExtPsePortPwrAvailable 4.9.402.1.2.1.8
This object indicates the amount of power available for the PD to use. This value may differ from the value cpeExtPsePortPwrAllocated due to the efficiency issues of delivering the power from the PSE to the PD. When sufficient power is available to power a PD, this value should be equal to the lower of the two objects, cpeExtDefaultAllocation and cpeExtPsePortPwrMax.
OBJECT-TYPE    
  Unsigned32  

cpeExtPsePortPwrConsumption 4.9.402.1.2.1.9
This indicates the actual power consumption of the PD connected to this interface. It may not necessarily be equal to the value of cpeExtPsePortPwrAvailable.
OBJECT-TYPE    
  Unsigned32  

cpeExtPsePortMaxPwrDrawn 4.9.402.1.2.1.10
This indicates the maximum amount of power drawn by the PD connected to this interface, since it was powered on.
OBJECT-TYPE    
  Unsigned32  

cpeExtPsePortEntPhyIndex 4.9.402.1.2.1.11
The entPhysicalIndex value that uniquely identifies the PSE port. If the PSE port does not have a corresponding physical entry in entPhysicalTable or if the entPhysicalTable is not supported by the management system, this object has the value of zero.
OBJECT-TYPE    
  EntPhysicalIndexOrZero  

cpeExtPsePortPolicingCapable 4.9.402.1.2.1.12
This object indicates whether the PSE port hardware is capable of policing the port for proper power consumption based on the allocated value.
OBJECT-TYPE    
  TruthValue  

cpeExtPsePortPolicingEnable 4.9.402.1.2.1.13
This object allows the user to turn on or turn off the power policing of the PSE port. If the instance value of cpeExtPsePortPolicingCapable is 'TRUE', the user is allowed to set this object to 'on' or 'off'. Otherwise, this object is read-only and always has the value of 'off'.
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cpeExtPsePortPolicingAction 4.9.402.1.2.1.14
This object specifies the power policing action that the device will take on this PSE port when the real-time power consumption exceeds its max power allocation if the value of cpeExtPsePortPolicingEnable is 'on'. 'deny' - the device will deny the power to the PSE port 'logOnly' - the device will not deny the power to the PSE port
OBJECT-TYPE    
  INTEGER deny(1), logOnly(2)  

cpeExtPsePortPwrManAlloc 4.9.402.1.2.1.15
This object specifies the manual power allocation that the PSE will allocate to the PD connected to this interface regardless of the amount requested via CDP or IEEE. Setting this object value to zero disables the manual power allocation. Warning: Misconfiguring this manual power allocation may cause damage to the system and void the warranty. Take precautions not to oversubscribe the power supply.
OBJECT-TYPE    
  Unsigned32  

cpeExtPsePortCapabilities 4.9.402.1.2.1.16
This object indicates the PSE functionality that this port supports. If the 'policing' BIT is set, then this PSE port is capable of policing the port for proper power consumption based on the allocated value. If the 'poePlus' BIT is set, then this PSE port supports PoE Plus functions.
OBJECT-TYPE    
  BITS policing(0), poePlus(1)  

cpeExtMainPseTable 4.9.402.1.3
This table contains the additional information for the main PSE group in pethMainPseTable.
OBJECT-TYPE    
  SEQUENCE OF  
    CpeExtMainPseEntry

cpeExtMainPseEntry 4.9.402.1.3.1
A cpeExtMainPseEntry contains information about a particular pethMainPseGroupIndex. An entry is created by the agent when a main PSE group is added to the pethMainPseTable. An entry is deleted by the agent when a main PSE group is removed from the pethMainPseTable.
OBJECT-TYPE    
  CpeExtMainPseEntry  

cpeExtMainPseEntPhyIndex 4.9.402.1.3.1.1
The entPhysicalIndex value that uniquely identifies the main PSE group. If the main PSE group does not have a corresponding physical entry in entPhysicalTable or if the entPhysicalTable is not supported by the management system, then this object has the value of zero.
OBJECT-TYPE    
  EntPhysicalIndexOrZero  

cpeExtMainPseDescr 4.9.402.1.3.1.2
A textual string containing information about the Power Source Equipment (PSE) group.
OBJECT-TYPE    
  SnmpAdminString  

cpeExtMainPsePwrMonitorCapable 4.9.402.1.3.1.3
This object indicates if the given group is capable of monitoring the power consumption of the interfaces that belong to the group. The value 'true' means that the group is capable. The value 'false' means that the group in not capable.
OBJECT-TYPE    
  TruthValue  

cpeExtPdStatistics 4.9.402.1.4
OBJECT IDENTIFIER    

cpeExtPdStatsTotalDevices 4.9.402.1.4.1
This object indicates the total number of the powered devices with any power classifications in the system. Classification is a way to tag different terminals on the Power over LAN network according to their power consumption. Devices such as IP telephones, WLAN access points and others, will be classified according to their power requirements.
OBJECT-TYPE    
  Unsigned32  

cpeExtPdStatsTable 4.9.402.1.4.2
This table contains the statistics information of the powered devices fallen into different power classifications in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    CpeExtPdStatsEntry

cpeExtPdStatsEntry 4.9.402.1.4.2.1
A cpeExtPdStatsEntry contains the statistics information about a particular power classification defined in cpeExtPdStatsIndex.
OBJECT-TYPE    
  CpeExtPdStatsEntry  

cpeExtPdStatsClass 4.9.402.1.4.2.1.1
The power classification as the index for the statistics information for powered devices. A value of 'cisco' indicates that the powered devices are CISCO proprietary and their power classification does not fall into any class in IEEE specifications. A value of 'class0' indicates that the power classification of the powered devices falls into class 0 in IEEE specifications. A value of 'class1' indicates that the power classification of the powered devices falls into class 1 in IEEE specifications. A value of 'class2' indicates that the power classification of the powered devices falls into class 2 in IEEE specifications. A value of 'class3' indicates that the power classification of the powered devices falls into class 3 in IEEE specifications. A value of 'class4' indicates that the power classification of the powered devices falls into class 4 in IEEE specifications.
OBJECT-TYPE    
  INTEGER cisco(1), class0(2), class1(3), class2(4), class3(5), class4(6)  

cpeExtPdStatsDeviceCount 4.9.402.1.4.2.1.2
This object indicates the count of the powered devices whose power classification falls into a specific value of cpeExtPdStatsIndex.
OBJECT-TYPE    
  Unsigned32  

cpeExtPolicingNotifEnable 4.9.402.1.5
This object is used to enable/disable the the cpeExtPolicingNotif notification.
OBJECT-TYPE    
  TruthValue  

cpeExtPowerPriorityEnable 4.9.402.1.6
This object is the global control of the power priority feature on the device. 'true' indicates that the power priority feature is globally enabled. 'false' indicates that the power priority feature is globally disabled.
OBJECT-TYPE    
  TruthValue  

cpeExtPsePortLldpTable 4.9.402.1.7
A table provides the Link Layer Discovery Protocol (LLDP) based Data Link Layer (DLL) power classification characteristics of PSE ports and PDs attached to them.
OBJECT-TYPE    
  SEQUENCE OF  
    CpeExtPsePortLldpEntry

cpeExtPsePortLldpEntry 4.9.402.1.7.1
A cpeExtPsePortLldpEntry entry contains the LLDP based 802.3at DLL power classification characteristics for a particular PSE and the PD attached to it. A PSE has its entry here when all of the following conditions are satisfied: - The LLDP power classification is globally enabled. - It has a PD attached. - LLDP is the operational power negotiation protocol between the PSE and the PD attached.
OBJECT-TYPE    
  CpeExtPsePortLldpEntry  

cpeExtPsePortLldpPwrType 4.9.402.1.7.1.1
The DTE Power via MDI type of the local system (PSE).
OBJECT-TYPE    
  CpeExtLldpPwrType  

cpeExtPsePortLldpPdPwrType 4.9.402.1.7.1.2
The DTE Power via MDI type of the remote system (PD).
OBJECT-TYPE    
  CpeExtLldpPwrType  

cpeExtPsePortLldpPwrSrc 4.9.402.1.7.1.3
The power source of the local system (PSE).
OBJECT-TYPE    
  CpeExtLldpPwrSrc  

cpeExtPsePortLldpPdPwrSrc 4.9.402.1.7.1.4
The power source of the remote system (PD).
OBJECT-TYPE    
  CpeExtLldpPwrSrc  

cpeExtPsePortLldpPwrPriority 4.9.402.1.7.1.5
The power priority of the local system (PSE).
OBJECT-TYPE    
  CpeExtPwrPriority  

cpeExtPsePortLldpPdPwrPriority 4.9.402.1.7.1.6
The power priority of the remote system (PD).
OBJECT-TYPE    
  CpeExtPwrPriority  

cpeExtPsePortLldpPwrReq 4.9.402.1.7.1.7
The requested PD power value that the local system (PSE) mirrors back to the remote system (PD).
OBJECT-TYPE    
  Unsigned32  

cpeExtPsePortLldpPdPwrReq 4.9.402.1.7.1.8
The PD requested power value received from the remote system (PD).
OBJECT-TYPE    
  Unsigned32  

cpeExtPsePortLldpPwrAlloc 4.9.402.1.7.1.9
The PSE allocated power value for the remote system (PD).
OBJECT-TYPE    
  Unsigned32  

cpeExtPsePortLldpPdPwrAlloc 4.9.402.1.7.1.10
The PSE allocated power value received from the remote system (PD).
OBJECT-TYPE    
  Unsigned32  

cpeExtPsePortLldpPwrClass 4.9.402.1.7.1.11
The PSE power classification sent to the remote PD via MDI TLV in LLDP Protocol.
OBJECT-TYPE    
  CpeExtLldpPwrClassOrZero  

cpeExtPsePortLldpPdPwrClass 4.9.402.1.7.1.12
This power classification received from the remote system (PD).
OBJECT-TYPE    
  CpeExtLldpPwrClassOrZero  

cpeExtPsePortLldpPdPwrSupport 4.9.402.1.7.1.13
This object indicates the power support mode received from the remote PD via MDI TLV in LLDP protocol. 'portClass' - This bit is set if the port is operating as PSE. Otherwise, it is operating as PD. 'pseMdiPwrSupport' - This bit is set if power is supported in MDI TLV. 'pseMdiPwrState' - This bit is set if power is enabled. 'psePairCtrlAbility' - This bit is set if pair selection can be controlled.
OBJECT-TYPE    
  BITS portClass(0), pseMdiPwrSupport(1), pseMdiPwrState(2), psePairCtrlAbility(3)  

cpeExtPsePortLldpPdPwrPairsOrZero 4.9.402.1.7.1.14
This object indicates the pinout pairs in use received from the remote PD via MDI TLV in LLDP Protocol. 'unknown' - information is not available 'signal' - the signal pairs are in use. 'spare' - the spare pairs are in use.
OBJECT-TYPE    
  INTEGER unknown(0), signal(1), spare(2)  

cpeExtPolicingNotif 4.9.402.0.1
This notification is generated when the 'overdraw' or 'overdrawLog' bit in value of cpeExtPsePortAdditionalStatus is set or cleared.
NOTIFICATION-TYPE    

cpeExtMIBCompliances 4.9.402.2.1
OBJECT IDENTIFIER    

cpeExtMIBGroups 4.9.402.2.2
OBJECT IDENTIFIER    

cpeExtMIBCompliance 4.9.402.2.1.1
The compliance statement for the CISCO-POWER-ETHERNET-EXT-MIB.
MODULE-COMPLIANCE    

cpeExtMIBCompliance2 4.9.402.2.1.2
The compliance statement for the CISCO-POWER-ETHERNET-EXT-MIB.
MODULE-COMPLIANCE    

cpeExtMIBCompliance3 4.9.402.2.1.3
The compliance statement for the CISCO-POWER-ETHERNET-EXT-MIB.
MODULE-COMPLIANCE    

cpeExtMIBCompliance4 4.9.402.2.1.4
The compliance statement for the CISCO-POWER-ETHERNET-EXT-MIB.
MODULE-COMPLIANCE    

cpeExtMIBCompliance5 4.9.402.2.1.5
The compliance statement for the CISCO-POWER-ETHERNET-EXT-MIB.
MODULE-COMPLIANCE    

cpeExtPsePortGroup 4.9.402.2.2.1
This group provides information and configuration objects in addition to those provided in the POWER-ETHERNET-MIB (RFC3621).
OBJECT-GROUP    

cpeExtPsePortGlobalConfigGroup 4.9.402.2.2.2
This is a collection of objects which provide global configuration of the PSE interfaces.
OBJECT-GROUP    

cpeExtPsePortPwrMonitorGroup 4.9.402.2.2.3
This is a collection of objects which provide power monitoring on PD's connected to the PSE interfaces.
OBJECT-GROUP    

cpeExtMainPseGroup 4.9.402.2.2.4
This is a collection of objects which provide additional information for the PSE group. cpeExtMainPseGroup object is superseded by cpeExtMainPseGroup2, and cpeExtPseGrpPwrGroup.
OBJECT-GROUP    

cpeExtPortEntityIndexGroup 4.9.402.2.2.5
This is a collection of objects which provide entity physical index information for PSE port.
OBJECT-GROUP    

cpeExtPortPolicingGroup 4.9.402.2.2.6
This is a collection of objects which provide the hardware power consumption policing information for PSE port.
OBJECT-GROUP    

cpeExtPdStatsGroup 4.9.402.2.2.7
This is a collection of objects which provide the statistics information for powered devices.
OBJECT-GROUP    

cpeExtMainPseGroup2 4.9.402.2.2.8
This is a collection of objects which provide additional information to identify the PSE group.
OBJECT-GROUP    

cpeExtPseGrpPwrGroup 4.9.402.2.2.9
This is a collection of objects which provide power monitoring information for the PSE group.
OBJECT-GROUP    

cpeExtPortPolicingActionGroup 4.9.402.2.2.10
This is a collection of objects which provide control of the power policing action of the PSE port.
OBJECT-GROUP    

cpeExtPortPwrManAllocGroup 4.9.402.2.2.11
This is a collection of objects which provide manual power allocation for the PSE port.
OBJECT-GROUP    

cpeExtPolicingNotifEnableGroup 4.9.402.2.2.12
A collection of object that provides control over power consumption policing status notification.
OBJECT-GROUP    

cpeExtPolicingNotifGroup 4.9.402.2.2.13
This is a collection of notifications related to power consumption policing information for PSE ports.
NOTIFICATION-GROUP    

cpeExtPowerPriorityGroup 4.9.402.2.2.14
A collection of objects which provides global control of power priority feature.
OBJECT-GROUP    

cpeExtPsePortLldpGroup 4.9.402.2.2.15
A collection of objects which provides the information about the LLDP based Data Link Layer power classification characteristics of power Ethernet PSE ports.
OBJECT-GROUP    

cpeExtPsePortCapabilitiesGroup 4.9.402.2.2.16
A collection of objects which provides PSE port capabilities.
OBJECT-GROUP    

cpeExtPsePortLldpPowerGroup 4.9.402.2.2.17
A collection of objects which provide Power information via MDI TLV in LLDP Protocol.
OBJECT-GROUP