CISCO-POP-MGMT-MIB

File: CISCO-POP-MGMT-MIB.mib (62494 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
IF-MIB DS1-MIB CISCO-SMI

Imported symbols

MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE
IpAddress Integer32 Gauge32
Counter32 TimeTicks Unsigned32
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP
DisplayString TimeStamp TruthValue
InterfaceIndexOrZero dsx1LineStatus dsx1LineIndex
ciscoExperiment

Defined Types

CpmDS0UsageEntry  
SEQUENCE    
  cpmDS1SlotIndex Integer32
  cpmDS1PortIndex Integer32
  cpmChannelIndex Integer32
  cpmConfiguredType INTEGER
  cpmDS0CallType INTEGER
  cpmL2Encapsulation INTEGER
  cpmCallCount Counter32
  cpmTimeInUse TimeTicks
  cpmInOctets Counter32
  cpmOutOctets Counter32
  cpmInPackets Counter32
  cpmOutPackets Counter32
  cpmAssociatedInterface InterfaceIndexOrZero

CpmDS1DS0UsageEntry  
SEQUENCE    
  cpmDS1UsageSlotIndex Integer32
  cpmDS1UsagePortIndex Integer32
  cpmDS1ActiveDS0s Gauge32
  cpmDS1ActiveDS0sHighWaterMark Counter32
  cpmDS1TotalAnalogCalls Counter32
  cpmDS1TotalDigitalCalls Counter32
  cpmDS1TotalV110Calls Counter32
  cpmDS1TotalV120Calls Counter32
  cpmDS1TotalCalls Counter32
  cpmDS1TotalTimeInUse Unsigned32
  cpmDS1CurrentIdle Gauge32
  cpmDS1CurrentOutOfService Gauge32
  cpmDS1CurrentBusyout Gauge32
  cpmDS1InOctets Counter32
  cpmDS1OutOctets Counter32
  cpmDS1InPackets Counter32
  cpmDS1OutPackets Counter32

CpmDS0StatusEntry  
SEQUENCE    
  cpmDS0OperStatus INTEGER
  cpmDS0BusyoutAdminStatus INTEGER
  cpmDS0BusyoutAllow TruthValue
  cpmDS0BusyoutStatus INTEGER
  cpmDS0BusyoutSource INTEGER
  cpmDS0BusyoutTime TimeStamp
  cpmDS0ConfigFunction INTEGER
  cpmDS0InterfaceIndex InterfaceIndexOrZero

CpmActiveCallSummaryEntry  
SEQUENCE    
  cpmActiveCallStartTimeIndex TimeStamp
  cpmActiveCallSummaryIndex Integer32
  cpmActiveUserID DisplayString
  cpmActiveUserIpAddr IpAddress
  cpmActiveCallType INTEGER
  cpmActiveModemSlot Integer32
  cpmActiveModemPort Integer32
  cpmActiveCallDuration TimeTicks
  cpmActiveEntrySlot Integer32
  cpmActiveEntryPort Integer32
  cpmActiveEntryChannel Integer32
  cpmActiveRemotePhoneNumber DisplayString
  cpmActiveLocalPhoneNumber DisplayString
  cpmActiveTTYNumber Integer32

CpmCallHistorySummaryEntry  
SEQUENCE    
  cpmCallDisconnectTimeIndex TimeStamp
  cpmCallStartTimeIndex TimeStamp
  cpmCallHistorySummaryIndex Integer32
  cpmUserID DisplayString
  cpmUserIpAddr IpAddress
  cpmCallType INTEGER
  cpmModemSlot Integer32
  cpmModemPort Integer32
  cpmCallDuration TimeTicks
  cpmEntrySlot Integer32
  cpmEntryPort Integer32
  cpmEntryChannel Integer32
  cpmRemotePhoneNumber DisplayString
  cpmLocalPhoneNumber DisplayString
  cpmTTYNumber Integer32

Defined Values

ciscoPopMgmtMIB 1.3.6.1.4.1.9.10.19
Cisco Point Of Presence Management MIB to provide DSX1 and DSX0 facilities management and call summaries.
MODULE-IDENTITY    

ciscoPopMgmtMIBObjects 1.3.6.1.4.1.9.10.19.1
OBJECT IDENTIFIER    

cpmDS0Usage 1.3.6.1.4.1.9.10.19.1.1
OBJECT IDENTIFIER    

cpmCallFailure 1.3.6.1.4.1.9.10.19.1.2
OBJECT IDENTIFIER    

cpmActiveCallSummary 1.3.6.1.4.1.9.10.19.1.3
OBJECT IDENTIFIER    

cpmCallHistorySummary 1.3.6.1.4.1.9.10.19.1.4
OBJECT IDENTIFIER    

cpmDS0Status 1.3.6.1.4.1.9.10.19.1.5
OBJECT IDENTIFIER    

cpmDS1LoopbackNotifyConfig 1.3.6.1.4.1.9.10.19.1.6
OBJECT IDENTIFIER    

cpmCallVolume 1.3.6.1.4.1.9.10.19.1.7
OBJECT IDENTIFIER    

cpmDS0UsageTable 1.3.6.1.4.1.9.10.19.1.1.1
The DS0 usage table is for hardware and software objects not used as interfaces, and not covered in rfc1213. These objects include analog calls coming over ISDN, Channelized T1, and Channelized E1. This table is created for every DS1 line in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    CpmDS0UsageEntry

cpmDS0UsageEntry 1.3.6.1.4.1.9.10.19.1.1.1.1
An entry in the DS0 Usage table.
OBJECT-TYPE    
  CpmDS0UsageEntry  

cpmDS1SlotIndex 1.3.6.1.4.1.9.10.19.1.1.1.1.1
The slot index indicates the slot number on the device where the DS1 card resides.
OBJECT-TYPE    
  Integer32 0..2147483647  

cpmDS1PortIndex 1.3.6.1.4.1.9.10.19.1.1.1.1.2
The port index indicates the port number of a specific DS1 on the DS1 card in the slot
OBJECT-TYPE    
  Integer32 0..2147483647  

cpmChannelIndex 1.3.6.1.4.1.9.10.19.1.1.1.1.3
The channel index that distinguishes the DS0 timeslot of the DS1 port. The range of the channel index is based on the number of T1/E1 channels: 1-24(T1) and 1-31(E1).
OBJECT-TYPE    
  Integer32 0..2147483647  

cpmConfiguredType 1.3.6.1.4.1.9.10.19.1.1.1.1.4
The configured technology for the channel: ISDN(2), Channelized T1 (3) or Channelized E1 (4).
OBJECT-TYPE    
  INTEGER unknown(1), isdn(2), ct1(3), ce1(4)  

cpmDS0CallType 1.3.6.1.4.1.9.10.19.1.1.1.1.5
The type of the current call carried by this DS0. idle - This DS0 is currently idle. unknown - The data type of the call currently occupying this DS0 is not one of the types listed here. analog - The data type of the call currently occupying this DS0 is analog, i.e. a modem call. digital - The data type of the call currently occupying this DS0 is digital. v110 - The call currently occupying this DS0 is a V110 call. v120 - The call currently occupying this DS0 is a V120 call. voice - The call currently occupying this DS0 is a voice call.
OBJECT-TYPE    
  INTEGER idle(1), unknown(2), analog(3), digital(4), v110(5), v120(6), voice(7)  

cpmL2Encapsulation 1.3.6.1.4.1.9.10.19.1.1.1.1.6
The data link encapsulation of the call currently occuppying this DS0: idle - This DS0 is currently idle. unknown - The encapsulation of the currently active call on this DS0 is not one of the options following. PPP - slip - arap - hdlc - exec - voice - voice encapsulation; IANA type voiceEncap(103)
OBJECT-TYPE    
  INTEGER idle(1), unknown(2), ppp(3), slip(4), arap(5), hdlc(6), exec(7), voice(8)  

cpmCallCount 1.3.6.1.4.1.9.10.19.1.1.1.1.7
The number of calls that have occupied this DS0.
OBJECT-TYPE    
  Counter32  

cpmTimeInUse 1.3.6.1.4.1.9.10.19.1.1.1.1.8
The amount of time that this DS0 has been in use. This is computed by summing up the call durations of all past calls that have occupied this DS0.
OBJECT-TYPE    
  TimeTicks  

cpmInOctets 1.3.6.1.4.1.9.10.19.1.1.1.1.9
The total number of octets received on this DS0 for data calls (cpmDS0CallType has the value 'analog(3)' or 'digital(4)' or 'v110(5)' or 'v120(6)'). All the received 'raw' octets are counted, including any protocol headers which may or may not be present, depending on the service type of data call.
OBJECT-TYPE    
  Counter32  

cpmOutOctets 1.3.6.1.4.1.9.10.19.1.1.1.1.10
The total number of octets transmitted on this DS0 for data calls (cpmDS0CallType has the value 'analog(3)' or 'digital(4)' or 'v110(5)' or 'v120(6)'). All the transmitted 'raw' octets are counted, including any protocol headers which may or may not be present, depending on the service type of data call.
OBJECT-TYPE    
  Counter32  

cpmInPackets 1.3.6.1.4.1.9.10.19.1.1.1.1.11
The total number of packets received on this DS0 for data calls (cpmDS0CallTyp has the value 'analog(3)' or 'digital(4)' or 'v110(5)' or 'v120(6)').
OBJECT-TYPE    
  Counter32  

cpmOutPackets 1.3.6.1.4.1.9.10.19.1.1.1.1.12
The total number of packets transmitted on this DS0 for data calls (cpmDS0CallTyp has the value 'analog(3)' or 'digital(4)' or 'v110(5)' or 'v120(6)').
OBJECT-TYPE    
  Counter32  

cpmAssociatedInterface 1.3.6.1.4.1.9.10.19.1.1.1.1.13
This is the value of ifIndex when the specific channel has an active call with a corresponding interface in the ifTable. For example, a digital ISDN call has a value pointing to the B-Channel entry in the ifTable. A modem call over ISDN or CT1/CE1 has a value pointing to the async interface of the modem assigned to this call. If the channel is idle, this value is 0.
OBJECT-TYPE    
  InterfaceIndexOrZero  

cpmISDNCfgBChanInUseForAnalog 1.3.6.1.4.1.9.10.19.1.1.2
The number of configured ISDN B-Channels that are currently occupied by analog calls.
OBJECT-TYPE    
  Gauge32  

cpmISDNCfgBChannelsInUse 1.3.6.1.4.1.9.10.19.1.1.3
The number of configured ISDN B-Channels that are currently occupied by both Digital and Analog calls.
OBJECT-TYPE    
  Gauge32  

cpmActiveDS0s 1.3.6.1.4.1.9.10.19.1.1.4
The number of DS0s that are currently in use.
OBJECT-TYPE    
  Gauge32  

cpmPPPCalls 1.3.6.1.4.1.9.10.19.1.1.5
The current number of active PPP calls received by the managed device
OBJECT-TYPE    
  Gauge32  

cpmV120Calls 1.3.6.1.4.1.9.10.19.1.1.6
The current number of active V.120 calls received by the managed device
OBJECT-TYPE    
  Gauge32  

cpmV110Calls 1.3.6.1.4.1.9.10.19.1.1.7
The current number of active V.110 calls received by the managed device
OBJECT-TYPE    
  Gauge32  

cpmActiveDS0sHighWaterMark 1.3.6.1.4.1.9.10.19.1.1.8
The high water mark for number of DS0s that are active simultaneously
OBJECT-TYPE    
  Counter32  

cpmDS1DS0UsageTable 1.3.6.1.4.1.9.10.19.1.1.9
The DS1-DS0-usage table is for hardware and software objects not used as interfaces, and not covered in rfc1213. These objects provide information on timeslots usage for a particular DS1.
OBJECT-TYPE    
  SEQUENCE OF  
    CpmDS1DS0UsageEntry

cpmDS1DS0UsageEntry 1.3.6.1.4.1.9.10.19.1.1.9.1
An entry in the DS0 Usage table.
OBJECT-TYPE    
  CpmDS1DS0UsageEntry  

cpmDS1UsageSlotIndex 1.3.6.1.4.1.9.10.19.1.1.9.1.1
The slot index indicates the slot number on the device where the DS1 card resides. The slot index of the first slot is starting from 0 and increment by 1 for the next slot in the device.
OBJECT-TYPE    
  Integer32 0..2147483647  

cpmDS1UsagePortIndex 1.3.6.1.4.1.9.10.19.1.1.9.1.2
The port index indicates the port number of a specific DS1 on the DS1 card in the slot. The port index of the first port is starting from 0 and increment by 1 for the next port on the DS1 card.
OBJECT-TYPE    
  Integer32 0..2147483647  

cpmDS1ActiveDS0s 1.3.6.1.4.1.9.10.19.1.1.9.1.3
The number of DS0s that are currently in use for a particular DS1.
OBJECT-TYPE    
  Gauge32  

cpmDS1ActiveDS0sHighWaterMark 1.3.6.1.4.1.9.10.19.1.1.9.1.4
The highest number of simultaneously actived DS0s on a specified DS1.
OBJECT-TYPE    
  Counter32  

cpmDS1TotalAnalogCalls 1.3.6.1.4.1.9.10.19.1.1.9.1.5
The accumulated number of analog data calls (cpmDS0CallType has the value 'analog(3)') on all ds0s within this DS1 since system startup. The object includes active and terminated calls.
OBJECT-TYPE    
  Counter32  

cpmDS1TotalDigitalCalls 1.3.6.1.4.1.9.10.19.1.1.9.1.6
The accumulated number of digital data calls (cpmDS0CallType has the value 'digital(4)') on all ds0s within this DS1 since system startup. The object includes active and terminated calls.
OBJECT-TYPE    
  Counter32  

cpmDS1TotalV110Calls 1.3.6.1.4.1.9.10.19.1.1.9.1.7
The accumulated number of v.110 data calls (cpmDS0CallType has the value 'v110(5)') on all ds0s within this DS1 since system startup. The object includes active and terminated calls.
OBJECT-TYPE    
  Counter32  

cpmDS1TotalV120Calls 1.3.6.1.4.1.9.10.19.1.1.9.1.8
The accumulated number of v.120 data calls (cpmDS0CallType has the value 'v120(6)') on all ds0s within this DS1 since system startup. The object includes active and terminated calls.
OBJECT-TYPE    
  Counter32  

cpmDS1TotalCalls 1.3.6.1.4.1.9.10.19.1.1.9.1.9
The total number of calls on all the DS0s within this DS1 since last system re-initialization. The object includes active and terminated calls. This only includes DS0s configured as bearer channels, not those configured for signaling, such as PRI D-channel.
OBJECT-TYPE    
  Counter32  

cpmDS1TotalTimeInUse 1.3.6.1.4.1.9.10.19.1.1.9.1.10
The total call duration on all the DS0s within this DS1 since last system re-initialization. This only includes DS0s configured as bearer channels, not those configured for signaling, such as PRI D-channel.
OBJECT-TYPE    
  Unsigned32  

cpmDS1CurrentIdle 1.3.6.1.4.1.9.10.19.1.1.9.1.11
The total number of DS0s currently in idle state within this DS1. This only includes DS0s configured as bearer and CAS channels, not those configured for signaling, such as PRI D-channel. See cpmDS0OperStatus in the cpmDS0StatusTable for individual DS0s.
OBJECT-TYPE    
  Gauge32  

cpmDS1CurrentOutOfService 1.3.6.1.4.1.9.10.19.1.1.9.1.12
The total number of DS0s in this DS1 currently placed out of service. This only includes DS0s configured as bearer and CAS channels, not those configured for signaling, such as PRI D-channel. See cpmDS0OperStatus in the cpmDS0StatusTable for individual DS0s.
OBJECT-TYPE    
  Gauge32  

cpmDS1CurrentBusyout 1.3.6.1.4.1.9.10.19.1.1.9.1.13
The total number of DS0s in this DS1 which currently have been requested to be busied out, but are not yet out of service. When an active call on a busied out DS0 terminates, the DS0 will be out of service, this object will be decremented and cpmDS1TotalOutOfService will be incremented. This only includes DS0s configured as bearer channels, not those configured for signaling, such as PRI D-channel. See cpmDS0AdminStatus in the cpmDS0StatusTable for individual DS0s.
OBJECT-TYPE    
  Gauge32  

cpmDS1InOctets 1.3.6.1.4.1.9.10.19.1.1.9.1.14
The total number of octets received over all the DS0 bearer channels within this DS1 since last system re-initialization. This value is a sum of all the cpmInOctets objects in the cpmDS0UsageTable for this DS1.
OBJECT-TYPE    
  Counter32  

cpmDS1OutOctets 1.3.6.1.4.1.9.10.19.1.1.9.1.15
The total number of octets transmitted over all the DS0 bearer channels within this DS1 since last system re-initialization. This value is a sum of all the cpmOutOctets objects in the cpmDS0UsageTable for this DS1.
OBJECT-TYPE    
  Counter32  

cpmDS1InPackets 1.3.6.1.4.1.9.10.19.1.1.9.1.16
The total number of data packets received over all the DS0 bearer channels within this DS1 since last system re-initialization. This value is a sum of all the cpmInPackets objects in the cpmDS0UsageTable for this DS1. It consists of PPP or PCM voice data packets.
OBJECT-TYPE    
  Counter32  

cpmDS1OutPackets 1.3.6.1.4.1.9.10.19.1.1.9.1.17
The total number of data packets transmitted over all the DS0 bearer channels within this DS1 since last system re-initialization. This value is a sum of all the cpmOutPackets objects in the cpmDS0UsageTable for this DS1. It consists of PPP or PCM voice data packets.
OBJECT-TYPE    
  Counter32  

cpmSW56CfgBChannelsInUse 1.3.6.1.4.1.9.10.19.1.1.10
The number of configured SW56 B-Channels that are currently occupied by Digital calls.
OBJECT-TYPE    
  Gauge32  

cpmISDNCfgBChanInUseForVoice 1.3.6.1.4.1.9.10.19.1.1.11
The number of configured ISDN B-Channels that are currently occupied by Voice calls.
OBJECT-TYPE    
  Gauge32  

cpmCASCfgBChanInUseForVoice 1.3.6.1.4.1.9.10.19.1.1.12
The number of configured CAS Channels that are currently occupied by Voice calls.
OBJECT-TYPE    
  Gauge32  

cpmISDNCfgActiveDChannels 1.3.6.1.4.1.9.10.19.1.1.13
The number of ISDN signaling channels which are active.
OBJECT-TYPE    
  Gauge32  

cpmISDNCfgBChannelsTimeInUse 1.3.6.1.4.1.9.10.19.1.1.14
The total call duration on all the ISDN B-channels since last system re-initialization.
OBJECT-TYPE    
  Counter32  

cpmISDNCfgBChannelsTimeInUseAnlg 1.3.6.1.4.1.9.10.19.1.1.15
The total analog call duration on all the ISDN B-channels since last system re-initialization. Analog call type is identified in cpmDS0CallType.
OBJECT-TYPE    
  Counter32  

cpmISDNCfgBChannelCalls 1.3.6.1.4.1.9.10.19.1.1.16
The total number of calls on all the ISDN B-channels since last system re-initialization.
OBJECT-TYPE    
  Counter32  

cpmISDNCfgBChannelAnalogCalls 1.3.6.1.4.1.9.10.19.1.1.17
The total number of analog calls on all the ISDN B-channels since last system re-initialization. Analog call type is identified in cpmDS0CallType.
OBJECT-TYPE    
  Counter32  

cpmTotalISDNSyncPPPCalls 1.3.6.1.4.1.9.10.19.1.1.18
The total number of ISDN-sync PPP calls received by the managed device since last system re-initialization.
OBJECT-TYPE    
  Counter32  

cpmDS0BusyoutNotifyEnable 1.3.6.1.4.1.9.10.19.1.5.1
This variable controls generation of cpmDS0BusyoutNotification. When this variable is 'true(1)', generation of cpmDS0BusyoutNotification is enabled. When this variable is 'false(2)', generation of cpmDS0BusyoutNotification is disabled. The default value is 'false(2)'.
OBJECT-TYPE    
  TruthValue  

cpmDS0StatusTable 1.3.6.1.4.1.9.10.19.1.5.2
The DS0 Status Table provides additional DS0 level information and configuration. This table is an extension of the cpmDS0UsageTable.
OBJECT-TYPE    
  SEQUENCE OF  
    CpmDS0StatusEntry

cpmDS0StatusEntry 1.3.6.1.4.1.9.10.19.1.5.2.1
Status for an individual DS0. This entry AUGMENTS the cpmDS0UsageEntry. An entry exists for each configured DS0 in the system.
OBJECT-TYPE    
  CpmDS0StatusEntry  

cpmDS0OperStatus 1.3.6.1.4.1.9.10.19.1.5.2.1.1
The operational state of the DSO. This object provides more detailed information than the IF-MIB ifOperStatus. unknown - The DSO is in an unknown state down - The DS0 is out of service idle - This DS0 is currently idle setup - A new connection is in the process of being established connected - A active connection exists test - The DSO is undergoing internal testing
OBJECT-TYPE    
  INTEGER unknown(1), down(2), idle(3), setup(4), connected(5), test(6)  

cpmDS0BusyoutAdminStatus 1.3.6.1.4.1.9.10.19.1.5.2.1.2
The administratively requested busyout state of the DSO. This object represents the desired busyout state of the DS0, which may or may not be reflected in the operation state, cpmDS0OperStatus. This object may be set via SNMP or the system console. noBusyout - No administrative busyout has been requested busyout - The DS0 will be shutdown when it next transitions to idle(2) cpmDS0OperStatus busyoutImmediate - Immediately transition the DS0 to down(2), terminating any current activity The effect of setting this object to busyout or busyoutImmediate is constrained by the value of cpmDS0BusyoutAllowed. If cpmDS0BusyoutAllowed has a value of false, attempting to set this object to busyout or busyoutImmediate will fail. This object provides more busyout information not available from the IF-MIB ifAdminStatus. This object reflects busyout requests configured on the local system as defined for the object cpmDS0BusyoutSource.
OBJECT-TYPE    
  INTEGER noBusyout(1), busyout(2), busyoutImmediate(3)  

cpmDS0BusyoutAllow 1.3.6.1.4.1.9.10.19.1.5.2.1.3
The object indicates if busyout requests for this DSO will be allowed. true - Setting cpmDS0BusyoutAdminStatus to busyout(2) or busyoutImmediate(3) will be accepted false - Busyout requests for this DS0 are not allowed The default value is true(1). If cpmDS0BusyoutAllowed has a value of false(2), attempting to set cpmDS0BusyoutAdminStatus to busyout or busyoutImmediate will fail. This object only constrains setting the value of cpmDS0BusyoutAdminStatus when cpmDS0BusyoutAdminStatus is set via SNMP.
OBJECT-TYPE    
  TruthValue  

cpmDS0BusyoutStatus 1.3.6.1.4.1.9.10.19.1.5.2.1.4
The busyout status of the DSO. noBusyout - The DS0 is not busied out nor has a busyout pending. busyoutPending - The DS0 has a busyout request pending. It will shutdown when it next transitions to idle(2) cpmDS0OperStatus. busiedOut - The DS0 is out of service due to a busyout request. This object is needed to reflect busyouts initiated other than administrativly, as described in cpmDS0BusyoutSource.
OBJECT-TYPE    
  INTEGER noBusyout(1), busyoutPending(2), busiedOut(3)  

cpmDS0BusyoutSource 1.3.6.1.4.1.9.10.19.1.5.2.1.5
The source of the busyout request either pending or active for the DSO. none - The DS0 is not busied out nor has a busyout request pending local - The DS0 is busied out or has a pending request due to an adminstrative command issued locally. internal - The DS0 is busied out or has a pending request due to internal system processing. remote - The DS0 is busied out or has a pending request due to a request from the peer switch.
OBJECT-TYPE    
  INTEGER none(1), local(2), internal(3), remote(4)  

cpmDS0BusyoutTime 1.3.6.1.4.1.9.10.19.1.5.2.1.6
Value of sysUpTime when the most recent busyout request was issued for this DS0. The value is zero indicates no busyout request has been issued.
OBJECT-TYPE    
  TimeStamp  

cpmDS0ConfigFunction 1.3.6.1.4.1.9.10.19.1.5.2.1.7
The object indicates the function this DSO is configured to provide. This object provides more detail than cpmConfiguredType. unknown - Unknown configuration t1SignallingChan - DS0 is configured as a T1 common channel signalling (CCS) such as ISDN PRI D-channel t1CcsBearerChan - DS0 is configured as a T1 common channel signalling (CCS) bearer channel e1SignallingChan - DS0 is configured as a E1 common channel signalling (CCS) such as ISDN PRI D-channel e1CcsBearerChan - DS0 is configured as a E1 common channel signalling (CCS) bearer channel t1CasChan - DS0 is configured as a T1 channel associated signalling channel e1CasChan - DS0 is configured as a E1 channel associated signalling channel
OBJECT-TYPE    
  INTEGER unknown(1), t1CcsSignallingChan(2), t1CcsBearerChan(3), e1CcsSignallingChan(4), e1CcsBearerChan(5), t1CasChan(6), e1CasChan(7)  

cpmDS0InterfaceIndex 1.3.6.1.4.1.9.10.19.1.5.2.1.8
This is the value of ifIndex in the ifTable for this DS0.
OBJECT-TYPE    
  InterfaceIndexOrZero  

cpmISDNCallsRejected 1.3.6.1.4.1.9.10.19.1.2.1
The number of rejected ISDN calls in this managed device.
OBJECT-TYPE    
  Counter32  

cpmModemCallsRejected 1.3.6.1.4.1.9.10.19.1.2.2
The number of rejected modem calls in this managed device.
OBJECT-TYPE    
  Counter32  

cpmISDNCallsClearedAbnormally 1.3.6.1.4.1.9.10.19.1.2.3
The number of connected ISDN calls that have been abnormally cleared, that is, they were cleared by some event other than the following: a - The transmission of a normal disconnect message by the local end. b - The reception of a normal disconnect message from the remote end.
OBJECT-TYPE    
  Counter32  

cpmModemCallsClearedAbnormally 1.3.6.1.4.1.9.10.19.1.2.4
The number of connected modem calls that have been abnormally cleared, that is, they were not cleared with the proper modem protocol handshakes.
OBJECT-TYPE    
  Counter32  

cpmISDNNoResource 1.3.6.1.4.1.9.10.19.1.2.5
The number of ISDN calls that have been rejected because there is no B-Channel available to handle the call.
OBJECT-TYPE    
  Counter32  

cpmModemNoResource 1.3.6.1.4.1.9.10.19.1.2.6
The number of modem calls that have been rejected because there is no modem available to handle the call.
OBJECT-TYPE    
  Counter32  

cpmCallVolSuccISDNDigital 1.3.6.1.4.1.9.10.19.1.7.1
The number of incoming and outgoing successful ISDN digital data calls (cpmDS0CallType has the value 'digital(4)'), since system startup. A successful call is a terminated call that has a disconnect cause of 'normal call clearing(16)'.
OBJECT-TYPE    
  Counter32  

cpmCallVolAnalogCallClearedNormally 1.3.6.1.4.1.9.10.19.1.7.2
The number of incoming and outgoing successful analog data calls which use modem resource (cpmDS0CallType has the value 'analog(3)'), since system startup. A successful call is a terminated call who is cleared by the proper modem protocol handshake.
OBJECT-TYPE    
  Counter32  

cpmActiveCallSummaryTable 1.3.6.1.4.1.9.10.19.1.3.1
The active call summary table is needed to track currently active calls. This table is needed because modem calls are not in CALL-HISTORY-MIB, and the DIAL-CONTROL_MIB is not yet available.
OBJECT-TYPE    
  SEQUENCE OF  
    CpmActiveCallSummaryEntry

cpmActiveCallSummaryEntry 1.3.6.1.4.1.9.10.19.1.3.1.1
An entry in the Call Summary table.
OBJECT-TYPE    
  CpmActiveCallSummaryEntry  

cpmActiveCallStartTimeIndex 1.3.6.1.4.1.9.10.19.1.3.1.1.1
The start time of the current call.
OBJECT-TYPE    
  TimeStamp  

cpmActiveCallSummaryIndex 1.3.6.1.4.1.9.10.19.1.3.1.1.2
Arbitrary small integer to distinguish calls that occured at the same time tick.
OBJECT-TYPE    
  Integer32 0..2147483647  

cpmActiveUserID 1.3.6.1.4.1.9.10.19.1.3.1.1.3
The User login ID or zero length string if unavailable.
OBJECT-TYPE    
  DisplayString Size(0..255)  

cpmActiveUserIpAddr 1.3.6.1.4.1.9.10.19.1.3.1.1.4
The IP address of the call or 0.0.0.0 if unavailable. This object comes directly from IOS.
OBJECT-TYPE    
  IpAddress  

cpmActiveCallType 1.3.6.1.4.1.9.10.19.1.3.1.1.5
The call type: unknown - None of the following analog - Modem call digital - Digital call v110 - V110 Call v120 - V120 Call voice - Voice Call
OBJECT-TYPE    
  INTEGER unknown(1), analog(2), digital(3), v110(4), v120(5), voice(6)  

cpmActiveModemSlot 1.3.6.1.4.1.9.10.19.1.3.1.1.6
Identification of modem resource allocated to call. This is the value of cmSlotIndex from CISCO-MODEM-MGMT-MIB. This value along with cpmActiveModemPort uniquely identifies a modem. Value is -1 if call does not utilize a modem.
OBJECT-TYPE    
  Integer32 0..2147483647  

cpmActiveModemPort 1.3.6.1.4.1.9.10.19.1.3.1.1.7
Identification of modem resource allocated to call. This is the value of cmPortIndex from CISCO-MODEM-MGMT-MIB. This value along with cpmActiveModemSlot uniquely identifies a modem. Value is -1 if call does not utilize a modem.
OBJECT-TYPE    
  Integer32 0..2147483647  

cpmActiveCallDuration 1.3.6.1.4.1.9.10.19.1.3.1.1.8
The duration of the current call.
OBJECT-TYPE    
  TimeTicks  

cpmActiveEntrySlot 1.3.6.1.4.1.9.10.19.1.3.1.1.9
The logical slot in which the DS1 line that the user connected on resides.
OBJECT-TYPE    
  Integer32 0..2147483647  

cpmActiveEntryPort 1.3.6.1.4.1.9.10.19.1.3.1.1.10
The logical port for the DS1 line that the user connected on.
OBJECT-TYPE    
  Integer32 0..2147483647  

cpmActiveEntryChannel 1.3.6.1.4.1.9.10.19.1.3.1.1.11
The channel within the DS1 that is allocated to the call.
OBJECT-TYPE    
  Integer32 0..2147483647  

cpmActiveRemotePhoneNumber 1.3.6.1.4.1.9.10.19.1.3.1.1.12
The remote telephone number. For a call into the device, this is the originating number. For a call out of the device, this is the dialed number. If not available the string length is zero.
OBJECT-TYPE    
  DisplayString Size(0..255)  

cpmActiveLocalPhoneNumber 1.3.6.1.4.1.9.10.19.1.3.1.1.13
The local telephone number. For a call into the device, this is the dialed number. For a call out of the device, this is the originating number. If not available the string length is zero.
OBJECT-TYPE    
  DisplayString Size(0..255)  

cpmActiveTTYNumber 1.3.6.1.4.1.9.10.19.1.3.1.1.14
The TTY number associated with this call. This information comes from the IOS 'show line' command.
OBJECT-TYPE    
  Integer32  

cpmCallHistorySummaryTableMaxLength 1.3.6.1.4.1.9.10.19.1.4.1
The upper limit on the number of entries that the cpmCallHistoryTable may contain. A value of 0 will prevent any history from being retained. When this table is full, the oldest entry will be deleted and the new one will be created.
OBJECT-TYPE    
  Integer32 0..500  

cpmCallHistorySummaryRetainTimer 1.3.6.1.4.1.9.10.19.1.4.2
The minimum amount of time that an cpmCallHistoryEntry will be maintained before being deleted. A value of 0 will prevent any history from being retained, but will not prevent callCompletion traps being genarated.
OBJECT-TYPE    
  Integer32 0..500  

cpmCallHistorySummaryTable 1.3.6.1.4.1.9.10.19.1.4.3
The call history summary table is needed to track ended active calls. This table is needed because modem calls are not in CALL-HISTORY-MIB; the CISCO-ISDN-MIB objects do not contain information about the active calls; and the DIAL-CONTROL_MIB is not yet available.
OBJECT-TYPE    
  SEQUENCE OF  
    CpmCallHistorySummaryEntry

cpmCallHistorySummaryEntry 1.3.6.1.4.1.9.10.19.1.4.3.1
An entry in the Call Summary table.
OBJECT-TYPE    
  CpmCallHistorySummaryEntry  

cpmCallDisconnectTimeIndex 1.3.6.1.4.1.9.10.19.1.4.3.1.1
The disconnect time of the call.
OBJECT-TYPE    
  TimeStamp  

cpmCallStartTimeIndex 1.3.6.1.4.1.9.10.19.1.4.3.1.2
The start time of the current call.
OBJECT-TYPE    
  TimeStamp  

cpmCallHistorySummaryIndex 1.3.6.1.4.1.9.10.19.1.4.3.1.3
Arbitrary small integer to distinguish calls that occured at the same time tick.
OBJECT-TYPE    
  Integer32 0..2147483647  

cpmUserID 1.3.6.1.4.1.9.10.19.1.4.3.1.4
The User login ID or zero length string if unavailable. This object comes directly from IOS.
OBJECT-TYPE    
  DisplayString Size(0..255)  

cpmUserIpAddr 1.3.6.1.4.1.9.10.19.1.4.3.1.5
The IP address of the call or 0.0.0.0 if unavailable. This object comes directly from IOS.
OBJECT-TYPE    
  IpAddress  

cpmCallType 1.3.6.1.4.1.9.10.19.1.4.3.1.6
The call type: unknown - None of the following analog - Modem call digital - Digital call v110 - V110 Call v120 - V120 Call voice - Voice Call
OBJECT-TYPE    
  INTEGER unknown(1), analog(2), digital(3), v110(4), v120(5), voice(6)  

cpmModemSlot 1.3.6.1.4.1.9.10.19.1.4.3.1.7
Identification of modem resource allocated to call. This is the value of cmSlotIndex from CISCO-MODEM-MGMT-MIB. This value along with cpmModemPort uniquely identifies a modem. Value is -1 if call does not utilize a modem.
OBJECT-TYPE    
  Integer32  

cpmModemPort 1.3.6.1.4.1.9.10.19.1.4.3.1.8
Identification of modem resource allocated to call. This is the value of cmPortIndex from CISCO-MODEM-MGMT-MIB. This value along with cpmModemSlot uniquely identifies a modem. Value is -1 if call does not utilize a modem.
OBJECT-TYPE    
  Integer32  

cpmCallDuration 1.3.6.1.4.1.9.10.19.1.4.3.1.9
The duration of the current call.
OBJECT-TYPE    
  TimeTicks  

cpmEntrySlot 1.3.6.1.4.1.9.10.19.1.4.3.1.10
The physical system slot in which the DS1 line that the user connected on resides.
OBJECT-TYPE    
  Integer32  

cpmEntryPort 1.3.6.1.4.1.9.10.19.1.4.3.1.11
The logical port for the DS1 line that the user connected on.
OBJECT-TYPE    
  Integer32  

cpmEntryChannel 1.3.6.1.4.1.9.10.19.1.4.3.1.12
The channel within the DS1 that is allocated to the call.
OBJECT-TYPE    
  Integer32  

cpmRemotePhoneNumber 1.3.6.1.4.1.9.10.19.1.4.3.1.13
The remote telephone number. For a call into the device, this is the originating number. For a call out of the device, this is the dialed number. If not available the string length is zero.
OBJECT-TYPE    
  DisplayString Size(0..255)  

cpmLocalPhoneNumber 1.3.6.1.4.1.9.10.19.1.4.3.1.14
The local telephone number. For a call into the device, this is the dialed number. For a call out of the device, this is the originating number. If not available the string length is zero.
OBJECT-TYPE    
  DisplayString Size(0..255)  

cpmTTYNumber 1.3.6.1.4.1.9.10.19.1.4.3.1.15
The TTY number associated with this call. This information comes from the IOS 'show line' command.
OBJECT-TYPE    
  Integer32  

cpmDS1LoopbackNotifyEnable 1.3.6.1.4.1.9.10.19.1.6.1
This variable controls the generation of cpmDS1LoopbackNotification When this variable is 'true(1)', generation of these notification is enabled. When this variable is 'false(2)', generation is disabled The default value is 'false(2)'.
OBJECT-TYPE    
  TruthValue  

cPopMgmtMIBNotificationPrefix 1.3.6.1.4.1.9.10.19.2
OBJECT IDENTIFIER    

cpmNotifications 1.3.6.1.4.1.9.10.19.2.0
OBJECT IDENTIFIER    

cpmDS0BusyoutNotification 1.3.6.1.4.1.9.10.19.2.0.1
This notification is sent when there is a state change in cpmDS0BusyoutStatus object.
NOTIFICATION-TYPE    

cpmDS1LoopbackNotification 1.3.6.1.4.1.9.10.19.2.0.2
This notification is sent when there is a state change in dsx1LineStatus object of RFC1406-MIB.
NOTIFICATION-TYPE    

cpmMIBConformance 1.3.6.1.4.1.9.10.19.3
OBJECT IDENTIFIER    

cpmMIBCompliances 1.3.6.1.4.1.9.10.19.3.1
OBJECT IDENTIFIER    

cpmMIBGroups 1.3.6.1.4.1.9.10.19.3.2
OBJECT IDENTIFIER    

cpmMIBCompliance 1.3.6.1.4.1.9.10.19.3.1.1
The compliance statement used in a PoPM Stack, which implement the Cisco PoP Management MIB
MODULE-COMPLIANCE    

cpmMIBComplianceRev1 1.3.6.1.4.1.9.10.19.3.1.2
The compliance statement used in a PoPM Stack, which implement the Cisco PoP Management MIB
MODULE-COMPLIANCE    

cpmComplianceRev2 1.3.6.1.4.1.9.10.19.3.1.3
The compliance statement used in a PoPM Stack, which implement the Cisco PoP Management MIB
MODULE-COMPLIANCE    

cpmMIBComplianceRev3 1.3.6.1.4.1.9.10.19.3.1.4
This group is mandatory only for systems supporting generation of notifications.
MODULE-COMPLIANCE    

cpmMIBComplianceRev4 1.3.6.1.4.1.9.10.19.3.1.5
This group is optional.
MODULE-COMPLIANCE    

cpmMIBComplianceRev5 1.3.6.1.4.1.9.10.19.3.1.6
This group is optional.
MODULE-COMPLIANCE    

cpmDS0UsageGroup 1.3.6.1.4.1.9.10.19.3.2.1
A collection of objects providing the analog and digital statistics for a DS1.
OBJECT-GROUP    

cpmCallFailureGroup 1.3.6.1.4.1.9.10.19.3.2.2
A collection of objects providing aggregate totals of call failures
OBJECT-GROUP    

cpmActiveCallSummaryGroup 1.3.6.1.4.1.9.10.19.3.2.3
A collection of objects providing the summary of the currently active calls.
OBJECT-GROUP    

cpmCallHistorySummaryGroup 1.3.6.1.4.1.9.10.19.3.2.4
A collection of objects providing the summary of calls that were recently terminated.
OBJECT-GROUP    

cpmDS0UsageGroupRev1 1.3.6.1.4.1.9.10.19.3.2.5
A collection of objects providing the analog and digital statistics for a DS1.
OBJECT-GROUP    

cpmDS0UsageGroupRev2 1.3.6.1.4.1.9.10.19.3.2.6
A collection of objects providing the analog and digital statistics for a DS1.
OBJECT-GROUP    

cpmDS1UsageGroup 1.3.6.1.4.1.9.10.19.3.2.7
A collection of objects providing statistics aggregation across DS0s within a DS1.
OBJECT-GROUP    

cpmSystemGroup 1.3.6.1.4.1.9.10.19.3.2.8
A collection of objects providing statistics aggregation for the entire system.
OBJECT-GROUP    

cpmDS0StatusGroup 1.3.6.1.4.1.9.10.19.3.2.9
A collection of objects providing the status for a DS0.
OBJECT-GROUP    

cpmNotificationGroup 1.3.6.1.4.1.9.10.19.3.2.10
The collection of notifications
NOTIFICATION-GROUP    

cpmDS1LoopbackNotifyConfigGroup 1.3.6.1.4.1.9.10.19.3.2.11
A collection of objects providing the notification configuration
OBJECT-GROUP    

cpmCallVolumeGroup 1.3.6.1.4.1.9.10.19.3.2.12
A collection of objects providing aggregate totals of call successfully completed
OBJECT-GROUP    

cpmNotificationGroupRev1 1.3.6.1.4.1.9.10.19.3.2.13
The collection of notifications
NOTIFICATION-GROUP