CISCO-MGX82XX-SONET-MIB

File: CISCO-MGX82XX-SONET-MIB.mib (144604 bytes)

Imported modules

RFC1155-SMI BASIS-MIB RFC-1212
RFC1213-MIB

Imported symbols

Counter Gauge cwsonetObjects
OBJECT-TYPE DisplayString

Defined Types

SonetConfigEntry  
SEQUENCE    
  sonetLineNum INTEGER
  sonetLineType INTEGER
  sonetLineLoopbackCommand INTEGER
  sonetHCSmasking INTEGER
  sonetPayloadScrambling INTEGER
  sonetFrameScrambling INTEGER
  sonetLineEnable INTEGER
  sonetLineXmtClkSrc INTEGER
  sonetRDIVType INTEGER
  sonetRDIPType INTEGER
  sonetTributaryType INTEGER
  sonetTributaryMappingType INTEGER
  sonetTributaryFramingFormat INTEGER
  sonetSignallingTransportMode INTEGER
  sonetTributaryGroupingType INTEGER

CwSonetMediumEntry  
SEQUENCE    
  cwSonetMediumType INTEGER
  cwSonetMediumTimeElapsed INTEGER
  cwSonetMediumValidIntervals INTEGER
  cwSonetMediumLineCoding INTEGER
  cwSonetMediumLineType INTEGER
  cwSonetMediumCircuitIdentifier DisplayString

CwSonetSectionCurrentEntry  
SEQUENCE    
  cwSonetSectionCurrentLineNum INTEGER
  cwSonetSectionCurrentStatus INTEGER
  cwSonetSectionCurrentValidFlag INTEGER
  cwSonetSectionCurrent15minTimeElapsed INTEGER
  cwSonetSectionCurrentESs Counter
  cwSonetSectionCurrentSESs Counter
  cwSonetSectionCurrentSEFSs Counter
  cwSonetSectionCurrentCVs Counter
  cwSonetSectionCurrentClrButton INTEGER

SonetSectionCurrentDayEntry  
SEQUENCE    
  sonetSectionCurrentDayLineNum INTEGER
  sonetSectionCurrentDayValidFlag INTEGER
  sonetSectionCurrentDayESs Counter
  sonetSectionCurrentDaySESs Counter
  sonetSectionCurrentDaySEFSs Counter
  sonetSectionCurrentDayCVs Counter
  sonetSectionCurrentDayClrButton INTEGER

CwSonetSectionIntervalEntry  
SEQUENCE    
  cwSonetSectionIntervalLineNum INTEGER
  cwSonetSectionIntervalNumber INTEGER
  cwSonetSectionIntervalValidFlag INTEGER
  cwSonetSectionIntervalESs Counter
  cwSonetSectionIntervalSESs Counter
  cwSonetSectionIntervalSEFss Counter
  cwSonetSectionIntervalCVs Counter

SonetSectionAlarmEntry  
SEQUENCE    
  sectionAlarmLineNum INTEGER
  sonetSectionStatisticalAlarmSeverity INTEGER
  sonetSectionCurrent15minESsThreshold INTEGER
  sonetSectionCurrentDayESsThreshold INTEGER
  sonetSectionCurrent15minSESsThreshold INTEGER
  sonetSectionCurrentDaySESsThreshold INTEGER
  sonetSectionCurrent15minSEFSsThreshold INTEGER
  sonetSectionCurrentDaySEFSsThreshold INTEGER
  sonetSectionCurrent15minCVsThreshold INTEGER
  sonetSectionCurrentDayCVsThreshold INTEGER
  sonetSectionTraceSelection INTEGER
  sonetSectionTraceToTransmit OCTET STRING
  sonetSectionTraceToExpect OCTET STRING
  sonetSectionTraceReceived OCTET STRING
  sonetSectionStatAlarmStatus INTEGER

SonetSectionCounterEntry  
SEQUENCE    
  sectionCounterLineNum INTEGER
  sonetSectionCounterLOSs Gauge
  sonetSectionCounterLOFs Gauge
  sonetSectionCounterClrButton INTEGER

CwSonetLineCurrentEntry  
SEQUENCE    
  cwSonetLineCurrentLineNum INTEGER
  cwSonetLineCurrentStatus INTEGER
  cwSonetLineCurrentValidFlag INTEGER
  cwSonetLineCurrent15minTimeElapsed INTEGER
  cwSonetLineCurrentESs Gauge
  cwSonetLineCurrentSESs Gauge
  cwSonetLineCurrentCVs Gauge
  cwSonetLineCurrentUASs Gauge
  cwSonetLineCurrentClrButton INTEGER

SonetLineCurrentDayEntry  
SEQUENCE    
  lineCurrentDayLineNum INTEGER
  sonetLineCurrentDayValidFlag INTEGER
  sonetLineCurrentDayESs Gauge
  sonetLineCurrentDaySESs Gauge
  sonetLineCurrentDayCVs Gauge
  sonetLineCurrentDayFCs Gauge
  sonetLineCurrentDayUASs Gauge
  sonetLineCurrentDayClrButton INTEGER

CwSonetLineIntervalEntry  
SEQUENCE    
  cwSonetLineIntervalLineNum INTEGER
  cwSonetLineIntervalNumber INTEGER
  cwSonetLineIntervalValidFlag INTEGER
  cwSonetLineIntervalESs Gauge
  cwSonetLineIntervalSESs Gauge
  cwSonetLineIntervalCVs Gauge
  cwSonetLineIntervalFCs Gauge
  cwSonetLineIntervalUASs Gauge

CwSonetFarEndLineCurrentEntry  
SEQUENCE    
  cwSonetFELineCurrentLineNum INTEGER
  cwSonetFarEndLineCurrentValidFlag INTEGER
  cwSonetFarEndLineCurrentTimeElapsed INTEGER
  cwSonetFarEndLineCurrentESs Gauge
  cwSonetFarEndLineCurrentSESs Gauge
  cwSonetFarEndLineCurrentCVs Gauge
  cwSonetFarEndLineCurrentFCs Gauge
  cwSonetFarEndLineCurrentUASs Gauge
  cwSonetFarEndLineCurrentClrButton INTEGER

SonetFarEndLineCurrentDayEntry  
SEQUENCE    
  sonetFELineCurrentDayLineNum INTEGER
  sonetFarEndLineCurrentDayValidFlag INTEGER
  sonetFarEndLineCurrentDayESs Gauge
  sonetFarEndLineCurrentDaySESs Gauge
  sonetFarEndLineCurrentDayCVs Gauge
  sonetFarEndLineCurrentDayFCs Gauge
  sonetFarEndLineCurrentDayUASs Gauge
  sonetFarEndLineCurrentDayClrButton INTEGER

CwSonetFarEndLineIntervalEntry  
SEQUENCE    
  cwSonetFELineIntervalLineNum INTEGER
  cwSonetFarEndLineIntervalNumber INTEGER
  cwSonetFarEndLineIntervalValidFlag INTEGER
  cwSonetFarEndLineIntervalESs Gauge
  cwSonetFarEndLineIntervalSESs Gauge
  cwSonetFarEndLineIntervalCVs Gauge
  cwSonetFarEndLineIntervalFCs Gauge
  cwSonetFarEndLineIntervalUASs Gauge

SonetLineAlarmEntry  
SEQUENCE    
  sonetLineAlarmLineNum INTEGER
  sonetLineStatisticalAlarmSeverity INTEGER
  sonetLineCurrent15minESsThreshold INTEGER
  sonetLineCurrentDayESsThreshold INTEGER
  sonetLineCurrent15minSESsThreshold INTEGER
  sonetLineCurrentDaySESsThreshold INTEGER
  sonetLineCurrent15minCVsThreshold INTEGER
  sonetLineCurrentDayCVsThreshold INTEGER
  sonetLineCurrent15minUASsThreshold INTEGER
  sonetLineCurrentDayUASsThreshold INTEGER
  sonetLineStatAlarmStatus INTEGER

SonetLineCounterEntry  
SEQUENCE    
  sonetLineCounterLineNum INTEGER
  sonetLineCounterAISs Gauge
  sonetLineCounterRFIs Gauge
  sonetLineCounterClrButton INTEGER

CwSonetPathCurrentEntry  
SEQUENCE    
  cwSonetPathCurrentLineNum INTEGER
  cwSonetPathCurrentStatus INTEGER
  cwSonetPathCurrentValidFlag INTEGER
  cwSonetPathCurrentTimeElapsed INTEGER
  cwSonetPathCurrentESs Gauge
  cwSonetPathCurrentSESs Gauge
  cwSonetPathCurrentCVs Gauge
  cwSonetPathCurrentFCs Gauge
  cwSonetPathCurrentUASs Gauge
  cwSonetPathCurrentClrButton INTEGER

SonetPathCurrentDayEntry  
SEQUENCE    
  sonetPathCurrentDayLineNum INTEGER
  sonetPathCurrentDayValidFlag INTEGER
  sonetPathCurrentDayESs Gauge
  sonetPathCurrentDaySESs Gauge
  sonetPathCurrentDayCVs Gauge
  sonetPathCurrentDayFCs Gauge
  sonetPathCurrentDayUASs Gauge
  sonetPathCurrentDayClrButton INTEGER

CwSonetPathIntervalEntry  
SEQUENCE    
  cwSonetPathIntervalLineNum INTEGER
  cwSonetPathIntervalNumber INTEGER
  cwSonetPathIntervalValidFlag INTEGER
  cwSonetPathIntervalESs Gauge
  cwSonetPathIntervalSESs Gauge
  cwSonetPathIntervalCVs Gauge
  cwSonetPathIntervalFCs Gauge
  cwSonetPathIntervalUASs Gauge

CwSonetFarEndPathCurrentEntry  
SEQUENCE    
  cwSonetFEPathCurrentLineNum INTEGER
  cwSonetFarEndPathCurrentValidFlag INTEGER
  cwSonetFarEndPathCurrentTimeElapsed INTEGER
  cwSonetFarEndPathCurrentESs Gauge
  cwSonetFarEndPathCurrentSESs Gauge
  cwSonetFarEndPathCurrentCVs Gauge
  cwSonetFarEndPathCurrentFCs Gauge
  cwSonetFarEndPathCurrentUASs Gauge
  cwSonetFarEndPathCurrentClrButton INTEGER

SonetFarEndPathCurrentDayEntry  
SEQUENCE    
  sonetFEPathCurrentDayLineNum INTEGER
  sonetFarEndPathCurrentDayValidFlag INTEGER
  sonetFarEndPathCurrentDayESs Gauge
  sonetFarEndPathCurrentDaySESs Gauge
  sonetFarEndPathCurrentDayCVs Gauge
  sonetFarEndPathCurrentDayFCs Gauge
  sonetFarEndPathCurrentDayUASs Gauge
  sonetFarEndPathCurrentDayClrButton INTEGER

CwSonetFarEndPathIntervalEntry  
SEQUENCE    
  cwSonetFEPathIntervalLineNum INTEGER
  cwSonetFarEndPathIntervalNumber INTEGER
  cwSonetFarEndPathIntervalValidFlag INTEGER
  cwSonetFarEndPathIntervalESs Gauge
  cwSonetFarEndPathIntervalSESs Gauge
  cwSonetFarEndPathIntervalCVs Gauge
  cwSonetFarEndPathIntervalFCs Gauge
  cwSonetFarEndPathIntervalUASs Gauge

SonetPathAlarmEntry  
SEQUENCE    
  sonetPathAlarmLineNum INTEGER
  sonetPathStatisticalAlarmSeverity INTEGER
  sonetPathCurrent15minESsThreshold INTEGER
  sonetPathCurrentDayESsThreshold INTEGER
  sonetPathCurrent15minSESsThreshold INTEGER
  sonetPathCurrentDaySESsThreshold INTEGER
  sonetPathCurrent15minCVsThreshold INTEGER
  sonetPathCurrentDayCVsThreshold INTEGER
  sonetPathCurrent15minUASsThreshold INTEGER
  sonetPathCurrentDayUASsThreshold INTEGER
  sonetPathTraceSelection INTEGER
  sonetPathTraceToTransmit OCTET STRING
  sonetPathTraceToExpect OCTET STRING
  sonetPathTraceReceived OCTET STRING
  sonetPathStatAlarmStatus INTEGER

SonetPathCounterEntry  
SEQUENCE    
  sonetPathCounterLineNum INTEGER
  sonetPathCounterAISs Gauge
  sonetPathCounterRFIs Gauge
  sonetPathCounterClrButton INTEGER

SonetApsConfigEntry  
SEQUENCE    
  apsWorkingSlot INTEGER
  apsWorkingLine INTEGER
  apsProtectionSlot INTEGER
  apsProtectionLine INTEGER
  apsEnable INTEGER
  apsArchMode INTEGER
  apsActiveLine INTEGER
  apsSFBER INTEGER
  apsSDBER INTEGER
  apsWtr INTEGER
  apsdirection INTEGER
  apsRevertive INTEGER
  apsK1K2Disable INTEGER

Defined Values

sonetConfig 1.1.1
OBJECT IDENTIFIER    

cwsonetMedium 1.1.2
OBJECT IDENTIFIER    

cwsonetSection 1.1.3
OBJECT IDENTIFIER    

cwsonetLine 1.1.4
OBJECT IDENTIFIER    

cwsonetPath 1.1.5
OBJECT IDENTIFIER    

sonetConfigTable 1.1.1.1
The SONET Configuration table. There is one row for each SONET port in the BASIS system. The table size (number of rows) is given by the value of sonetLineNumOfValidEntries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonetConfigEntry

sonetConfigEntry 1.1.1.1.1
An entry in the SONET Configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SonetConfigEntry  

sonetLineNum 1.1.1.1.1.1
This object is the identifier of a SONET Interface on a managed device. For MGX8850(For example PXM1 Module): OC-3 : sonetLineNum in a range 1..4 OC-12: sonetLineNum = 1 is the ONLY valid number For Other: sonetLineNum = 1 is the ONLY valid number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

sonetLineType 1.1.1.1.1.2
This variable indicates the cell framing. Defaults to Sts-3c
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sonetSts3c(1), sonetStm1(2), sonetSts12c(3), sonetStm4(4), sonetSts48c(5), sonetStm16(6), sonetSts192c(7), sonetStm64(8), sonetSts3(9)  

sonetLineLoopbackCommand 1.1.1.1.1.3
This variable represents the loopback configuration of the SONET interface. The values mean: sonetNoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as it's value. sonetRemoteLineLoop Near End loops back Remote data sonetLocalLineLoop Near End loops back Local data.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sonetNoLoop(1), sonetRemoteLineLoop(2), sonetLocalLineLoop(3)  

sonetHCSmasking 1.1.1.1.1.4
HCS masking. Defaults to enable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

sonetPayloadScrambling 1.1.1.1.1.5
STS3c or STM-1 payload scrambling. Defaults to enable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

sonetFrameScrambling 1.1.1.1.1.6
STS3c or STM-1 frame scrambling. Defaults to enable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

sonetLineEnable 1.1.1.1.1.7
This variable indicates if the line is enabled or not defaults to disable
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sonetLineXmtClkSrc 1.1.1.1.1.8
This represents the type of transmit clock source. backplaneClk: clock source is from the controller card, transmitted via the backplane to the service module. recoverClk: clock is recovered from the received signal. localClk: clock is from a local oscillator on the card. Default is backplaneClk.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER backplaneClk(1), recoverClk(2), localClk(3)  

sonetRDIVType 1.1.1.1.1.9
This variable represents the type of RDI-V sent by this NE to remote NE. onebit: use 1 bit RDI-V. Compatible with older equipment. threebit: use 3 bit, enhanced RDI-V. Defaults to onebit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER onebit(1), threebit(3)  

sonetRDIPType 1.1.1.1.1.10
This variable represents the type of RDI-P sent by this NE to remote NE. onebit: use 1 bit RDI-P. Compatible with older equipment. threebit: use 3 bit, enhanced RDI-P. Defaults to onebit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER onebit(1), threebit(3)  

sonetTributaryType 1.1.1.1.1.11
Type of tributary carried within the Sonet/Sdh signal. vt15vc11: carries T1 signals (VT15 or VC11) vt2vc12: carries E1 signals (VT2 or VC12) Default is vt15vc11 for Sonet interfaces and vt2vc12 for SDH interfaces.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER vt15vc11(1), vt2vc12(2)  

sonetTributaryMappingType 1.1.1.1.1.12
Type of VT/VC mapping. asynchronous: In this mode, the channel structure of the DS1/E1 is neither visible nor preserved. byteSynchronous: In this mode, the DS0 channels inside the VC/VT can be found and extracted. Default is asynchronous.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER asynchronous(1), byteSynchronous(2)  

sonetTributaryFramingFormat 1.1.1.1.1.13
Type of vt framing format. Is applicable only in byte-sync mapping mode for T1 tributaries. notApplicable: if VT mapping is not byte-sync. sf: superframe format. esf: extended superframe format. Default is esf if sonetTributaryMappingType is set to byteSynchronous, else the default is notApplicable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notApplicable(1), sf(2), esf(3)  

sonetSignallingTransportMode 1.1.1.1.1.14
The mode used to transport DS0 signalling information for T1 byte-sync mapping. notApplicable: if byte-sync mapping is not used. signallingTransferMode: the robbed bit signalling is transferred into the S bits of the VT header and framing bit is discarded. clearMode: only the framing bit is transferred to VT header. The signalling bits are left intact in the VT payload. Default is signallingTransferMode if sonetTributaryMappingType is set to byteSynchronous, else the default is notApplicable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notApplicable(1), signallingTransferMode(2), clearMode(3)  

sonetTributaryGroupingType 1.1.1.1.1.15
This variable indicates the method used to group VCs into an STM-1 signal. Applicable only to SDH. notApplicable: for sonet interfaces. au3Grouping: STM-1 <- AU-3 <- TUG-2 <- TU-12 <- VC12 or STM-1 <- AU-3 <- TUG-2 <- TU-11 <- VC11. au4Grouping: STM-1 <- AU-4 <- TUG-3 <- TUG-2 <- TU-12 <- VC12 or STM-1 <- AU-4 <- TUG-3 <- TUG-2 <- TU-11 <- VC11. Defaults to au3Grouping for SDH interfaces and notApplicable for Sonet interfaces.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notApplicable(1), au3Grouping(2), au4Grouping(3)  

sonetConfigNumOfValidEntries 1.1.1.2
The number of SONET configuration entries (regardless of their current configuration) in the sonetConfigTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cwSonetMediumTable 1.1.2.1
Sonet medium table parameters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwSonetMediumEntry

cwSonetMediumEntry 1.1.2.1.1
An entry in the SONET/SDH Medium table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CwSonetMediumEntry  

cwSonetMediumType 1.1.2.1.1.1
This variable identifies whether a SONET or a SDH signal is used across this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER sonet(1), sdh(2)  

cwSonetMediumTimeElapsed 1.1.2.1.1.2
The number of seconds, including partial seconds, that have elapsed since the beginning of the mandatory error-measurement period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..900  

cwSonetMediumValidIntervals 1.1.2.1.1.3
The number of previous intervals for which valid data has been stored. A SONET device must support at least n intervals. The minimum value of n is 4. The default of n is 32. The maximum value of n is 96. The value of this object will be n unless the device was brought online within the last (nx15) minutes, in which case the value will be the number of complete 15 minute intervals the device has been online.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

cwSonetMediumLineCoding 1.1.2.1.1.4
This variable describes the line coding for this interface. The B3ZS and CMI are used for electrical SONET/SDH signals (STS-1 and STS-3). The Non-Return to Zero (NRZ) and the Return to Zero are used for optical SONET/SDH signals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER sonetMediumOther(1), sonetMediumB3ZS(2), sonetMediumCMI(3), sonetMediumNRZ(4), sonetMediumRZ(5)  

cwSonetMediumLineType 1.1.2.1.1.5
This variable describes the line type for this interface. The line types are Short and Long Range Single Mode fiber or Multi-Mode fiber interfaces, and coax and UTP for electrical interfaces. The value sonetOther should be used when the Line Type is not one of the listed values.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER sonetOther(1), sonetShortSingleMode(2), sonetLongSingleMode(3), sonetMultiMode(4), sonetCoax(5), sonetUTP(6)  

cwSonetMediumCircuitIdentifier 1.1.2.1.1.6
This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cwSonetSectionCurrentTable 1.1.3.1
The SONET/SDH Section Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwSonetSectionCurrentEntry

cwSonetSectionCurrentEntry 1.1.3.1.1
An entry in the SONET/SDH Section Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CwSonetSectionCurrentEntry  

cwSonetSectionCurrentLineNum 1.1.3.1.1.1
line number. There are Max 1 line Num
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

cwSonetSectionCurrentStatus 1.1.3.1.1.2
This variable indicates the status of the sonet section layer. The cwSonetSectionCurrentStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetSectionNoDefect should be set if and only if no other flag is set. The various bit positions are: bit 1 = sonetSectionNoDefect bit 2 = sonetSectionLOS bit 3 = sonetSectionLOF
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..6  

cwSonetSectionCurrentValidFlag 1.1.3.1.1.3
Indicates if the current 15min bucket is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

cwSonetSectionCurrent15minTimeElapsed 1.1.3.1.1.4
The number of seconds, including partial seconds, that have elapsed since the beginning of the 15min error-measurement period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..900  

cwSonetSectionCurrentESs 1.1.3.1.1.5
The counter associated with the number of Errored Seconds encountered by a SONET/SDH Section in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cwSonetSectionCurrentSESs 1.1.3.1.1.6
The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Section in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cwSonetSectionCurrentSEFSs 1.1.3.1.1.7
The counter associated with the number of Severely Errored Framing Seconds encountered by a SONET/SDH Section in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cwSonetSectionCurrentCVs 1.1.3.1.1.8
The counter associated with the number of Coding Violations encountered by a SONET/SDH Section in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cwSonetSectionCurrentClrButton 1.1.3.1.1.9
Clears all the Section's Current15min counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), clear(2)  

sonetSectionCurrentDayTable 1.1.3.2
The SONET/SDH Section CurrentDay table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonetSectionCurrentDayEntry

sonetSectionCurrentDayEntry 1.1.3.2.1
An entry in the SONET/SDH Section CurrentDay table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SonetSectionCurrentDayEntry  

sonetSectionCurrentDayLineNum 1.1.3.2.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

sonetSectionCurrentDayValidFlag 1.1.3.2.1.2
Indicates if the current day bucket is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

sonetSectionCurrentDayESs 1.1.3.2.1.3
The counter associated with the number of Errored Seconds encountered by a SONET/SDH Section in the CurrentDay one day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sonetSectionCurrentDaySESs 1.1.3.2.1.4
The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Section in the CurrentDay minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sonetSectionCurrentDaySEFSs 1.1.3.2.1.5
The counter associated with the number of Severely Errored Framing Seconds encountered by a SONET/SDH Section in the CurrentDay one day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sonetSectionCurrentDayCVs 1.1.3.2.1.6
The counter associated with the number of Coding Violations encountered by a SONET/SDH Section in the CurrentDay one day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sonetSectionCurrentDayClrButton 1.1.3.2.1.7
Clears all the Section's Current Day counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), clear(2)  

cwSonetSectionIntervalTable 1.1.3.3
The SONET/SDH Section Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwSonetSectionIntervalEntry

cwSonetSectionIntervalEntry 1.1.3.3.1
An entry in the SONET/SDH Section Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CwSonetSectionIntervalEntry  

cwSonetSectionIntervalLineNum 1.1.3.3.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

cwSonetSectionIntervalNumber 1.1.3.3.1.2
A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

cwSonetSectionIntervalValidFlag 1.1.3.3.1.3
Indicates if the bucket specified by the interval is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

cwSonetSectionIntervalESs 1.1.3.3.1.4
The counter associated with the number of Errored Seconds encountered by a SONET/SDH Section in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cwSonetSectionIntervalSESs 1.1.3.3.1.5
The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Section in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cwSonetSectionIntervalSEFss 1.1.3.3.1.6
The counter associated with the number of Severely Errored Framing Seconds encountered by a SONET/SDH Section in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cwSonetSectionIntervalCVs 1.1.3.3.1.7
The counter associated with the number of Coding Violations encountered by a SONET/SDH Section in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sonetSectionAlarmTable 1.1.3.4
The SONET/SDH Section Alarm table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonetSectionAlarmEntry

sonetSectionAlarmEntry 1.1.3.4.1
An entry in the SONET/SDH Section Alarm table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SonetSectionAlarmEntry  

sectionAlarmLineNum 1.1.3.4.1.1
line number. BNM has 1 line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

sonetSectionStatisticalAlarmSeverity 1.1.3.4.1.2
When any statistical threshold is exceeded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minor(1), major(2)  

sonetSectionCurrent15minESsThreshold 1.1.3.4.1.3
The default is set to 20.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetSectionCurrentDayESsThreshold 1.1.3.4.1.4
The default is set to 200.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetSectionCurrent15minSESsThreshold 1.1.3.4.1.5
The default is set to 3.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetSectionCurrentDaySESsThreshold 1.1.3.4.1.6
The default is set to 7.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetSectionCurrent15minSEFSsThreshold 1.1.3.4.1.7
The default is set to 3.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetSectionCurrentDaySEFSsThreshold 1.1.3.4.1.8
The default is set to 7.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetSectionCurrent15minCVsThreshold 1.1.3.4.1.9
The default is set to 25.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetSectionCurrentDayCVsThreshold 1.1.3.4.1.10
The default is set to 250.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetSectionTraceSelection 1.1.3.4.1.11
Sonet Section Trace Selection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), sixtyFourBytes(2), sixtyFourBytesCrlf(3), sixteenBytes(4), sixteenBytesCrc7(5), sixteenBytesMsb1(6)  

sonetSectionTraceToTransmit 1.1.3.4.1.12
Sonet Section Trace To Transmit. 16-64 bytes String. If 16 byte trace is selected, FW will only use bytes 0-15 of the string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

sonetSectionTraceToExpect 1.1.3.4.1.13
Sonet Section Trace To Expect. 16-64 bytes String. If 16 byte trace is selected, FW will only use bytes 0-15 of the string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

sonetSectionTraceReceived 1.1.3.4.1.14
Sonet Section Trace Received. 16-64 bytes String. The write option is for debugging only.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

sonetSectionStatAlarmStatus 1.1.3.4.1.15
This variable indicates the status of the interface. The sonetSectionStatAlarmStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetLineStatAlarmNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sonetSectionStatAlarmNoDefect 2 sonetSectionCurrent15minESs 3 sonetSectionCurrent15minSESs 4 sonetSectionCurrent15minSEFSs 5 sonetSectionCurrent15minCVs 6 sonetSectionCurrentDayESs 7 sonetSectionCurrentDaySESs 8 sonetSectionCurrentDaySEFSs 9 sonetSectionCurrentDayCVs
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..1FF  

sonetSectionCounterTable 1.1.3.5
The SONET/SDH Section Counter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonetSectionCounterEntry

sonetSectionCounterEntry 1.1.3.5.1
An entry in the SONET/SDH Section table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SonetSectionCounterEntry  

sectionCounterLineNum 1.1.3.5.1.1
line number. There are Max 1 line on the BNM
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

sonetSectionCounterLOSs 1.1.3.5.1.2
The counter associated with the number of LOSs encountered by a SONET/SDH.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetSectionCounterLOFs 1.1.3.5.1.3
The counter associated with the number of LOFs encountered by a SONET/SDH Section.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetSectionCounterClrButton 1.1.3.5.1.4
Clears all the Section's counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), clear(2)  

cwSonetLineCurrentTable 1.1.4.1
The SONET/SDH Line Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwSonetLineCurrentEntry

cwSonetLineCurrentEntry 1.1.4.1.1
An entry in the SONET/SDH Line Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CwSonetLineCurrentEntry  

cwSonetLineCurrentLineNum 1.1.4.1.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

cwSonetLineCurrentStatus 1.1.4.1.1.2
This variable indicates the status of the sonet line layer. The cwSonetLineCurrentStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetLineNoDefect should be set if and only if no other flag is set. The various bit positions are: bit 1 = sonetLineNoDefect bit 2 = sonetLineRcvAIS bit 3 = sonetLineRcvRDI bit 4 = sonetLineXmtAis bit 5 = sonetLineXmtRdi
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..30  

cwSonetLineCurrentValidFlag 1.1.4.1.1.3
Indicates if the current 15min bucket is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

cwSonetLineCurrent15minTimeElapsed 1.1.4.1.1.4
The number of seconds, including partial seconds, that have elapsed since the beginning of the 15min error-measurement period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..900  

cwSonetLineCurrentESs 1.1.4.1.1.5
The counter associated with the number of Errored Seconds encountered by a SONET/SDH Line in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetLineCurrentSESs 1.1.4.1.1.6
The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Line in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetLineCurrentCVs 1.1.4.1.1.7
The counter associated with the number of Coding Violations encountered by a SONET/SDH Line in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetLineCurrentUASs 1.1.4.1.1.8
The counter associated with the number of Unavailable Seconds encountered by a SONET/SDH Line in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetLineCurrentClrButton 1.1.4.1.1.9
Clears all the SONET Line's Current15min counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), clear(2)  

sonetLineCurrentDayTable 1.1.4.2
The SONET/SDH Line Current Day table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonetLineCurrentDayEntry

sonetLineCurrentDayEntry 1.1.4.2.1
An entry in the SONET/SDH Line Current Day table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SonetLineCurrentDayEntry  

lineCurrentDayLineNum 1.1.4.2.1.1
line number. BNM has 1 line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

sonetLineCurrentDayValidFlag 1.1.4.2.1.2
Indicates if the current day bucket is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

sonetLineCurrentDayESs 1.1.4.2.1.3
The counter associated with the number of Errored Seconds encountered by a SONET/SDH Line in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetLineCurrentDaySESs 1.1.4.2.1.4
The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Line in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetLineCurrentDayCVs 1.1.4.2.1.5
The counter associated with the number of Coding Violations (BIP-8*N for STS-N) encountered by a SONET/SDH Line in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetLineCurrentDayFCs 1.1.4.2.1.6
Number of times that line was in AIS alarm in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetLineCurrentDayUASs 1.1.4.2.1.7
The counter associated with the number of Unavailable Seconds encountered by a SONET/SDH Line in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetLineCurrentDayClrButton 1.1.4.2.1.8
Clears all the SONET Line's CurrentDay counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), clear(2)  

cwSonetLineIntervalTable 1.1.4.3
The SONET/SDH Line Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwSonetLineIntervalEntry

cwSonetLineIntervalEntry 1.1.4.3.1
An entry in the SONET/SDH Line Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CwSonetLineIntervalEntry  

cwSonetLineIntervalLineNum 1.1.4.3.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

cwSonetLineIntervalNumber 1.1.4.3.1.2
A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

cwSonetLineIntervalValidFlag 1.1.4.3.1.3
Indicates if the bucket specified by the interval is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

cwSonetLineIntervalESs 1.1.4.3.1.4
The counter associated with the number of Errored Seconds encountered by a SONET/SDH Line in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetLineIntervalSESs 1.1.4.3.1.5
The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Line in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetLineIntervalCVs 1.1.4.3.1.6
The counter associated with the number of Coding Violations (BIP-8*N) encountered by a SONET/SDH Line in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetLineIntervalFCs 1.1.4.3.1.7
Number of times that line was in AIS alarm in the particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetLineIntervalUASs 1.1.4.3.1.8
The counter associated with the number of Unavailable Seconds encountered by a SONET/SDH Line in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndLineCurrentTable 1.1.4.4
The SONET/SDH Far End Line Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwSonetFarEndLineCurrentEntry

cwSonetFarEndLineCurrentEntry 1.1.4.4.1
An entry in the SONET/SDH Far End Line Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CwSonetFarEndLineCurrentEntry  

cwSonetFELineCurrentLineNum 1.1.4.4.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

cwSonetFarEndLineCurrentValidFlag 1.1.4.4.1.2
Indicates if the Far End current 15min bucket is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

cwSonetFarEndLineCurrentTimeElapsed 1.1.4.4.1.3
The number of seconds, including partial seconds, that have elapsed since the beginning of the 15min error-measurement period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..900  

cwSonetFarEndLineCurrentESs 1.1.4.4.1.4
The counter associated with the number of Far Far End Errored Seconds encountered by a SONET/SDH interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndLineCurrentSESs 1.1.4.4.1.5
The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Medium/Section/Line interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndLineCurrentCVs 1.1.4.4.1.6
The counter associated with the number of Far End Coding Violations reported via the far end block error (FEBE) count encountered by a SONET/SDH Medium/Section/Line interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndLineCurrentFCs 1.1.4.4.1.7
The counter associated with the number of RFI failures occurred in the current 15 min.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndLineCurrentUASs 1.1.4.4.1.8
The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Medium/Section/Line interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndLineCurrentClrButton 1.1.4.4.1.9
Clears all the SONET Far End Line's Current 15min counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), clear(2)  

sonetFarEndLineCurrentDayTable 1.1.4.5
The SONET/SDH Far End Line CurrentDay table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonetFarEndLineCurrentDayEntry

sonetFarEndLineCurrentDayEntry 1.1.4.5.1
An entry in the SONET/SDH Far End Line CurrentDay table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SonetFarEndLineCurrentDayEntry  

sonetFELineCurrentDayLineNum 1.1.4.5.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

sonetFarEndLineCurrentDayValidFlag 1.1.4.5.1.2
Indicates if the Far End current day bucket is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

sonetFarEndLineCurrentDayESs 1.1.4.5.1.3
The counter associated with the number of Far Far End Errored Seconds encountered by a SONET/SDH interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetFarEndLineCurrentDaySESs 1.1.4.5.1.4
The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Medium/Section/Line interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetFarEndLineCurrentDayCVs 1.1.4.5.1.5
The counter associated with the number of Far End Coding Violations reported via the far end block error (FEBE) count encountered by a SONET/SDH Medium/Section/Line interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetFarEndLineCurrentDayFCs 1.1.4.5.1.6
The counter associated with the number of RFI failures occurred in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetFarEndLineCurrentDayUASs 1.1.4.5.1.7
The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Medium/Section/Line interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetFarEndLineCurrentDayClrButton 1.1.4.5.1.8
Clears all the SONET Far End Line's Current Day counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), clear(2)  

cwSonetFarEndLineIntervalTable 1.1.4.6
The SONET/SDH Far End Line Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwSonetFarEndLineIntervalEntry

cwSonetFarEndLineIntervalEntry 1.1.4.6.1
An entry in the SONET/SDH Far End Line Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CwSonetFarEndLineIntervalEntry  

cwSonetFELineIntervalLineNum 1.1.4.6.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

cwSonetFarEndLineIntervalNumber 1.1.4.6.1.2
A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

cwSonetFarEndLineIntervalValidFlag 1.1.4.6.1.3
Indicates if the bucket specified by the interval is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

cwSonetFarEndLineIntervalESs 1.1.4.6.1.4
The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH Line interface in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndLineIntervalSESs 1.1.4.6.1.5
The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Line interface in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndLineIntervalCVs 1.1.4.6.1.6
The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH Line interface in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndLineIntervalFCs 1.1.4.6.1.7
The counter associated with the number of RFI failures in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndLineIntervalUASs 1.1.4.6.1.8
The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Line interface in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetLineAlarmTable 1.1.4.7
The SONET/SDH Line Alarm table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonetLineAlarmEntry

sonetLineAlarmEntry 1.1.4.7.1
An entry in the SONET/SDH Line Alarm table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SonetLineAlarmEntry  

sonetLineAlarmLineNum 1.1.4.7.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

sonetLineStatisticalAlarmSeverity 1.1.4.7.1.2
When any statistical threshold is exceeded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minor(1), major(2)  

sonetLineCurrent15minESsThreshold 1.1.4.7.1.3
The default is set to 20. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetLineCurrentDayESsThreshold 1.1.4.7.1.4
The default is set to 200. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetLineCurrent15minSESsThreshold 1.1.4.7.1.5
The default is set to 3. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetLineCurrentDaySESsThreshold 1.1.4.7.1.6
The default is set to 7. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetLineCurrent15minCVsThreshold 1.1.4.7.1.7
The default is set to 25. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetLineCurrentDayCVsThreshold 1.1.4.7.1.8
The default is set to 250. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetLineCurrent15minUASsThreshold 1.1.4.7.1.9
The default is set to 10. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetLineCurrentDayUASsThreshold 1.1.4.7.1.10
The default is set to 10. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetLineStatAlarmStatus 1.1.4.7.1.11
This variable indicates the status of the interface. The sonetLineStatAlarmStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetLineStatAlarmNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sonetLineStatAlarmNoDefect 2 sonetLineCurrent15minESs 3 sonetLineCurrent15minSESs 4 sonetLineCurrent15minCVs 5 sonetLineCurrent15minUASs 6 sonetFarEndLineCurrent15minESs 7 sonetFarEndLineCurrent15minSESs 8 sonetFarEndLineCurrent15minCVs 9 sonetFarEndLineCurrent15minUASs 10 sonetLineCurrentDayESs 11 sonetLineCurrentDaySESs 12 sonetLineCurrentDayCVs 13 sonetLineCurrentDayUASs 14 sonetFarEndLineCurrentDayESs 15 sonetFarEndLineCurrentDaySESs 16 sonetFarEndLineCurrentDayCVs 17 sonetFarEndLineCurrentDayUASs
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1FFFF  

sonetLineCounterTable 1.1.4.8
The SONET/SDH Line Counter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonetLineCounterEntry

sonetLineCounterEntry 1.1.4.8.1
An entry in the SONET/SDH Line table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SonetLineCounterEntry  

sonetLineCounterLineNum 1.1.4.8.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

sonetLineCounterAISs 1.1.4.8.1.2
The counter associated with the number of AISs encountered by a SONET/SDH.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetLineCounterRFIs 1.1.4.8.1.3
The counter associated with the number of RFIs encountered by a SONET/SDH Line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetLineCounterClrButton 1.1.4.8.1.4
Clears all the Line's counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), clear(2)  

cwSonetPathCurrentTable 1.1.5.1
The SONET/SDH Path Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwSonetPathCurrentEntry

cwSonetPathCurrentEntry 1.1.5.1.1
An entry in the SONET/SDH Path Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CwSonetPathCurrentEntry  

cwSonetPathCurrentLineNum 1.1.5.1.1.1
line number. BNM has 1 line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

cwSonetPathCurrentStatus 1.1.5.1.1.2
This variable indicates the status of the sonet path layer. The cwSonetPathCurrentStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetPathNoDefect should be set if and only if no other flag is set. The various bit positions are: bit 1 = sonetPathNoDefect bit 2 = sonetPathRcvLOP bit 3 = sonetPathRcvAIS bit 4 = sonetPathRcvRDI bit 5 = sonetPathUnequipted bit 6 = sonetPathSignalLabelMismatch bit 7 = sonetPathTraceFailure bit 8 = sonetPathXmtAis bit 9 = sonetPathXmtRdi bit 10 = sonetPathRcvLOCD
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1022  

cwSonetPathCurrentValidFlag 1.1.5.1.1.3
Indicates if the current 15min bucket is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

cwSonetPathCurrentTimeElapsed 1.1.5.1.1.4
The number of seconds, including partial seconds, that have elapsed since the beginning of the 15min error-measurement period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..900  

cwSonetPathCurrentESs 1.1.5.1.1.5
The counter associated with the number of Errored Seconds encountered by a SONET/SDH Path in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetPathCurrentSESs 1.1.5.1.1.6
The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Path in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetPathCurrentCVs 1.1.5.1.1.7
The counter associated with the number of Coding Violations (BIP-8) encountered by a SONET/SDH Path in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetPathCurrentFCs 1.1.5.1.1.8
Number of times that Path was in AIS or LOP alarm in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetPathCurrentUASs 1.1.5.1.1.9
The counter associated with the number of Unavailable Seconds encountered by a Path in the current 15 minute, interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetPathCurrentClrButton 1.1.5.1.1.10
Clears all the SONET Path's Current counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), clear(2)  

sonetPathCurrentDayTable 1.1.5.2
The SONET/SDH Path CurrentDay table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonetPathCurrentDayEntry

sonetPathCurrentDayEntry 1.1.5.2.1
An entry in the SONET/SDH Path CurrentDay table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SonetPathCurrentDayEntry  

sonetPathCurrentDayLineNum 1.1.5.2.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

sonetPathCurrentDayValidFlag 1.1.5.2.1.2
Indicates if the current day bucket is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

sonetPathCurrentDayESs 1.1.5.2.1.3
The counter associated with the number of Errored Seconds encountered by a SONET/SDH Path in the Current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetPathCurrentDaySESs 1.1.5.2.1.4
The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Path in the Current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetPathCurrentDayCVs 1.1.5.2.1.5
The counter associated with the number of Coding Violations (BIP-8) encountered by a SONET/SDH Path in the Current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetPathCurrentDayFCs 1.1.5.2.1.6
Number of times that Path was in AIS or LOP alarm in the Current interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetPathCurrentDayUASs 1.1.5.2.1.7
The counter associated with the number of Unavailable Seconds encountered by a Path in the Current day, interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetPathCurrentDayClrButton 1.1.5.2.1.8
Clears all the SONET Path's CurrentDay counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), clear(2)  

cwSonetPathIntervalTable 1.1.5.3
The SONET/SDH Path Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwSonetPathIntervalEntry

cwSonetPathIntervalEntry 1.1.5.3.1
An entry in the SONET/SDH Path Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CwSonetPathIntervalEntry  

cwSonetPathIntervalLineNum 1.1.5.3.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

cwSonetPathIntervalNumber 1.1.5.3.1.2
A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

cwSonetPathIntervalValidFlag 1.1.5.3.1.3
Indicates if the bucket specified by the interval is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

cwSonetPathIntervalESs 1.1.5.3.1.4
The counter associated with the number of Errored Seconds encountered by a SONET/SDH Path in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetPathIntervalSESs 1.1.5.3.1.5
The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Path in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetPathIntervalCVs 1.1.5.3.1.6
The counter associated with the number of Coding Violations encountered by a SONET/SDH Path in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetPathIntervalFCs 1.1.5.3.1.7
Number of times that Path was in AIS or LOP alarm in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetPathIntervalUASs 1.1.5.3.1.8
The counter associated with the number of Unavailable Seconds encountered by a Path in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndPathCurrentTable 1.1.5.4
The SONET/SDH Far End Path Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwSonetFarEndPathCurrentEntry

cwSonetFarEndPathCurrentEntry 1.1.5.4.1
An entry in the SONET/SDH Far End Path Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CwSonetFarEndPathCurrentEntry  

cwSonetFEPathCurrentLineNum 1.1.5.4.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

cwSonetFarEndPathCurrentValidFlag 1.1.5.4.1.2
Indicates if the Far End current 15min bucket is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

cwSonetFarEndPathCurrentTimeElapsed 1.1.5.4.1.3
The number of seconds, including partial seconds, that have elapsed since the beginning of the 15min error-measurement period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..900  

cwSonetFarEndPathCurrentESs 1.1.5.4.1.4
The counter associated with the number of Far Far End Errored Seconds encountered by a SONET/SDH interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndPathCurrentSESs 1.1.5.4.1.5
The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Path interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndPathCurrentCVs 1.1.5.4.1.6
The counter associated with the number of Far End Coding Violations reported via the far end block error (FEBE) count encountered by a SONET/SDH Path interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndPathCurrentFCs 1.1.5.4.1.7
The counter associated with the number of RFIs in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndPathCurrentUASs 1.1.5.4.1.8
The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Path interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndPathCurrentClrButton 1.1.5.4.1.9
Clears all the Far End Path Current counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), clear(2)  

sonetFarEndPathCurrentDayTable 1.1.5.5
The SONET/SDH Far End Path CurrentDay table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonetFarEndPathCurrentDayEntry

sonetFarEndPathCurrentDayEntry 1.1.5.5.1
An entry in the SONET/SDH Far End Path CurrentDay table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SonetFarEndPathCurrentDayEntry  

sonetFEPathCurrentDayLineNum 1.1.5.5.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

sonetFarEndPathCurrentDayValidFlag 1.1.5.5.1.2
Indicates if the Far End current day bucket is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

sonetFarEndPathCurrentDayESs 1.1.5.5.1.3
The counter associated with the number of Far Far End Errored Seconds encountered by a SONET/SDH interface in the Current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetFarEndPathCurrentDaySESs 1.1.5.5.1.4
The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Path interface in the Current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetFarEndPathCurrentDayCVs 1.1.5.5.1.5
The counter associated with the number of Far End Coding Violations reported via the far end block error (FEBE) count encountered by a SONET/SDH Path interface in the Current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetFarEndPathCurrentDayFCs 1.1.5.5.1.6
The counter associated with the number of RFIs in the Current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetFarEndPathCurrentDayUASs 1.1.5.5.1.7
The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Path interface in the Current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetFarEndPathCurrentDayClrButton 1.1.5.5.1.8
Clears all the Far End Path CurrentDay counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), clear(2)  

cwSonetFarEndPathIntervalTable 1.1.5.6
The SONET/SDH Far End Path Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwSonetFarEndPathIntervalEntry

cwSonetFarEndPathIntervalEntry 1.1.5.6.1
An entry in the SONET/SDH Far End Path Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CwSonetFarEndPathIntervalEntry  

cwSonetFEPathIntervalLineNum 1.1.5.6.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

cwSonetFarEndPathIntervalNumber 1.1.5.6.1.2
A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

cwSonetFarEndPathIntervalValidFlag 1.1.5.6.1.3
Indicates if the bucket specified by the interval is valid or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notValid(1), valid(2)  

cwSonetFarEndPathIntervalESs 1.1.5.6.1.4
The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH Path interface in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndPathIntervalSESs 1.1.5.6.1.5
The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Path interface in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndPathIntervalCVs 1.1.5.6.1.6
The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH Path interface in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndPathIntervalFCs 1.1.5.6.1.7
The counter associated with the number of RFIs in in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cwSonetFarEndPathIntervalUASs 1.1.5.6.1.8
The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Path interface in a particular 15-minute interval in the past 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetPathAlarmTable 1.1.5.7
The SONET/SDH Path Alarm table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonetPathAlarmEntry

sonetPathAlarmEntry 1.1.5.7.1
An entry in the SONET/SDH Path Alarm table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SonetPathAlarmEntry  

sonetPathAlarmLineNum 1.1.5.7.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

sonetPathStatisticalAlarmSeverity 1.1.5.7.1.2
When any statistical threshold is exceeded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minor(1), major(2)  

sonetPathCurrent15minESsThreshold 1.1.5.7.1.3
The default is set to 20. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetPathCurrentDayESsThreshold 1.1.5.7.1.4
The default is set to 200. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetPathCurrent15minSESsThreshold 1.1.5.7.1.5
The default is set to 3. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetPathCurrentDaySESsThreshold 1.1.5.7.1.6
The default is set to 7. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetPathCurrent15minCVsThreshold 1.1.5.7.1.7
The default is set to 25. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetPathCurrentDayCVsThreshold 1.1.5.7.1.8
The default is set to 250. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetPathCurrent15minUASsThreshold 1.1.5.7.1.9
The default is set to 10. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetPathCurrentDayUASsThreshold 1.1.5.7.1.10
The default is set to 10. This threshold is the same for Far End and Near End.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sonetPathTraceSelection 1.1.5.7.1.11
Sonet Path Trace Selection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), sixtyFourBytes(2), sixtyFourBytesCrlf(3), sixteenBytes(4), sixteenBytesCrc7(5), sixteenBytesMsb1(6)  

sonetPathTraceToTransmit 1.1.5.7.1.12
Sonet Path Trace To Transmit. 64-bytes String. If 16 byte trace is selected, FW will only use bytes 0-15 of the string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

sonetPathTraceToExpect 1.1.5.7.1.13
Sonet Path Trace To Expect. 64-bytes String. If 16 byte trace is selected, FW will only use bytes 0-15 of the string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

sonetPathTraceReceived 1.1.5.7.1.14
Sonet Path Trace Received. 64-bytes String. The write option is for debugging only.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

sonetPathStatAlarmStatus 1.1.5.7.1.15
This variable indicates the status of the interface. The sonetPathStatAlarmStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetPathStatAlarmNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sonetPathStatAlarmNoDefect 2 sonetPathCurrent15minESs 3 sonetPathCurrent15minSESs 4 sonetPathCurrent15minCVs 5 sonetPathCurrent15minUASs 6 sonetFarEndPathCurrent15minESs 7 sonetFarEndPathCurrent15minSESs 8 sonetFarEndPathCurrent15minCVs 9 sonetFarEndPathCurrent15minUASs 10 sonetPathCurrentDayESs 11 sonetPathCurrentDaySESs 12 sonetPathCurrentDayCVs 13 sonetPathCurrentDayUASs 14 sonetFarEndPathCurrentDayESs 15 sonetFarEndPathCurrentDaySESs 16 sonetFarEndPathCurrentDayCVs 17 sonetFarEndPathCurrentDayUASs
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1FFFF  

sonetPathCounterTable 1.1.5.8
The SONET/SDH Path Counter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonetPathCounterEntry

sonetPathCounterEntry 1.1.5.8.1
An entry in the SONET/SDH Path table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SonetPathCounterEntry  

sonetPathCounterLineNum 1.1.5.8.1.1
line number. BNM has one line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1  

sonetPathCounterAISs 1.1.5.8.1.2
The counter associated with the number of AISs encountered by a SONET/SDH.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetPathCounterRFIs 1.1.5.8.1.3
The counter associated with the number of RFIs encountered by a SONET/SDH Path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sonetPathCounterClrButton 1.1.5.8.1.4
Clears all the Path's counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), clear(2)  

sonetApsConfig 1.1.6
OBJECT IDENTIFIER    

sonetApsConfigTable 1.1.6.1
The Sonet APS config table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonetApsConfigEntry

sonetApsConfigEntry 1.1.6.1.1
An entry in the Sonet APS table. Each Entry is index by the working Line number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SonetApsConfigEntry  

apsWorkingSlot 1.1.6.1.1.1
This object is the chassis slot number of the working line MGX 8x50 PXM: can only be slot 7 or 8. MGX 8x30 PXM: can only be slot 1 or 2. MGX 8x50 SRME: can only be slot 15,16,31 or 32 MGX 8x30 SRME: can only be slot 7 or 14
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..32  

apsWorkingLine 1.1.6.1.1.2
This object is the line number of the working line OC-3 : sonetLineNum in a range 1..4 OC-12: sonetLineNum = 1 is the ONLY valid number
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4  

apsProtectionSlot 1.1.6.1.1.3
This object is the chassis slot number of the protection line MGX 8x50 PXM: can only be slot 7 or 8. MGX 8x30 PXM: can only be slot 1 or 2. MGX 8x50 SRME: can only be slot 15,16,31 or 32 MGX 8x30 SRME: can only be slot 7 or 14
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..32  

apsProtectionLine 1.1.6.1.1.4
This object is the line number of the working line OC-3 : sonetLineNum in a range 1..4 OC-12: sonetLineNum = 1 is the ONLY valid number
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4  

apsEnable 1.1.6.1.1.5
This object is used to enable or disable APS feature on the working/protection line pairs.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER apsFeatDisable(1), apsFeatEnable(2)  

apsArchMode 1.1.6.1.1.6
This object is used to configure APS architecture mode on the working/protection line pairs. The architecture modes currently supported are 'dualCardonePlusOne' (for GR-253) and 'anexAOnePlusOne (for G.783 Annex A).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER singleCardonePlusOne(1), dualCardonePlusOne(2), singleCardOneToOne(3), anexBOnePlusOne(4), anexAOnePlusOne(5)  

apsActiveLine 1.1.6.1.1.7
This object indicates which line is currently active ob the trunk line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER apsWorkingLine(1), apsProtectionLine(2)  

apsSFBER 1.1.6.1.1.8
This object contains the Bit Error Rate threshold for Signal Fault detection on the working line.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 3..13  

apsSDBER 1.1.6.1.1.9
This object contains the Bit Error Rate threshold for Signal Degrade detection on the working line. If set to 5, it means SDBER rate = 10 ^^ -5.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..13  

apsWtr 1.1.6.1.1.10
This object contains interval (in minute) to wait before attempting to switch back to working line. Not applicable if the line configure in non-revertive mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..12  

apsdirection 1.1.6.1.1.11
This object is used to configure the switching direction which this APS line support. Unidirectional switch only one direction. Bidirectional switch in both ends of the line.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER uniDirectional(1), biDirectional(2)  

apsRevertive 1.1.6.1.1.12
This object is used to configure the APS revertive or nonrevertive option. Revertive allows the line to be switch back to working line after the Wait-To-restore interval has expired and the working line SF/SD has been cleared.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER nonrevertive(1), revertive(2)  

apsK1K2Disable 1.1.6.1.1.13
This object is used to enable or disable the K1/K2 inband interface on the protection line.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER kbandEnable(1), kbandDisable(2)  

apsCardFailureCode 1.1.6.2
The Sonet APS card failure code apsProtectBCMissing = protection Back card missing apsProtectDCMissing = protection Daughter card missing apsWorkingBCMissing = Working Back card missing apsWorkingDCMissing = Working Daughter card missing apsWorkingCdMismatch = Working Card in mismatch/fail state apsProtectCdMismatch = protection card in mismatch/fail state
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER apsProtectBCMissing(1), apsProtectDCMissing(2), apsWorkingBCMissing(3), apsWorkingDCMissing(4), apsWorkingCdMismatch(5), apsProtectCdMismatch(6)  

apsLineFailureCode 1.1.6.3
The Sonet APS line failure code
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER apsSignalDegrade(1), apsSignalFailure(2), apsLineAlarm(3), apsLineLoopBack(4)  

apsLineSwReason 1.1.6.4
The Sonet APS line switch reason code
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER apsRevertive(1), apsManual(2), apsSignalDefectLow(3), apsSignalDefectHigh(4), apsSignalFailureLow(5), apsSignalFailureHigh(6), apsForceSwitch(7), apsLockOut(8)  

apsLineSwFailureCode 1.1.6.5
The Sonet APS line switch failure code
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER apsRevertiveSwitchFail(1), apsManualSwitchFail(2), apsSDLowSwitchFail(3), apsSDHighSwitchFail(4), apsSFLowSwitchFail(5), apsSFHighSwitchFail(6), apsForceSwitchFail(7), apsLockOutSwitchFail(8)  

apsStandbyLineFailureCode 1.1.6.6
The Sonet APS standby line failure code
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER apsSignalDegrade(1), apsSignalFailure(2), apsLineAlarm(3), apsLineLoopBack(4), apsProtectionByteFail(5), apsArchitectureMismatch(6), apsChannelMismatch(7), apsDirectionMismatch(8), apsWrongRequest(9)