CISCO-MGX82XX-PXM-CLOCK-MIB

File: CISCO-MGX82XX-PXM-CLOCK-MIB.mib (13491 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
BASIS-MIB CISCOWAN-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
MODULE-COMPLIANCE OBJECT-GROUP TEXTUAL-CONVENTION
cardSpecific ciscoWan

Defined Types

CmpClockConnectorType  
Represents the connector type for the clock device. rj45Type(1): RJ-45 Connector. This is for T1/E1 clock input. smbType (2): SMB Connector. This is for E1 clock input.
TEXTUAL-CONVENTION    
  INTEGER rj45Type(1), smbType(2)  

CmpClockSourceType  
This object identifies the source of the Mux Clock on PXM card. pxmInbandClock1 (1), pxmInbandClock2 (5): clock is derived from physical line pxmServiceModuleClock1(2), pxmServiceModuleClock2(6): clock is derived from service module. pxmTopSRMClock (3), pxmBottomSRMClock (7): clock is derived from SRM module. pxmExternalClock(4), pxmExternalClock2(9) :clock is derived from the port. pxmInternalOscillator (8): clock is derived from internal oscillator.
TEXTUAL-CONVENTION    
  INTEGER pxmInbandClock1(1), pxmServiceModuleClock1(2), pxmTopSRMClock(3), pxmExternalClock(4), pxmInbandClock2(5), pxmServiceModuleClock2(6), pxmBottomSRMClock(7), pxmInternalOscillator(8), pxmExternalClock2(9)  

CmpCurrentClock  
This TEXTUAL Convention represents the clock source currently selected for PXM card. primary(1): The primary clock source is described by pxmPrimaryMuxClockSource secondary(2): The secondary clock source is described by pxmSecondaryMuxClockSource. intOscillator(3): Current clock is internal oscillator.
TEXTUAL-CONVENTION    
  INTEGER primary(1), secondary(2), intOscillator(3)  

CmpClockExistence  
This TEXTUAL Convention represents the existence of the clock source. clkNotPresent (1): The T1/E1 external clock not present. clkPresent (2): The T1/E1 external clock present.
TEXTUAL-CONVENTION    
  INTEGER clkNotPresent(1), clkPresent(2)  

CmpClockImpedance  
This Textual Convention provides the impedance on external clock input on PXM-UI-S3 back card.
TEXTUAL-CONVENTION    
  INTEGER ohms75(1), ohms100(2), ohms120(3)  

Defined Values

ciscoMgx82xxPxmClockMIB 1.3.6.1.4.1.351.150.72
The MIB module to describe the clock configuration in Processor Switch Module(PXM) in MGX82xx product. Back cards supported for PXM1: PXM-UI : T1 Clock port, E1 Clock Port PXM-UI-S3 : External Clock1 for T1/E1 Clock input.
MODULE-IDENTITY    

pxmClockConfig 1.3.6.1.4.1.351.110.3.16
OBJECT IDENTIFIER    

pxmPrimaryMuxClockSource 1.3.6.1.4.1.351.110.3.16.1
This object identifies the source of the Primary Mux Clock for PXM card.
Status: current Access: read-only
OBJECT-TYPE    
  CmpClockSourceType  

pxmPrimaryInbandClockSourceLineNumber 1.3.6.1.4.1.351.110.3.16.2
This object indicates the inband line number. This is applicable when pxmPrimaryMuxClockSource is pxmInbandClock1(1) or pxmServiceModuleClock2 (5).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4  

pxmPrimarySMClockSourceSlotNumber 1.3.6.1.4.1.351.110.3.16.3
This object indicates the service module slot number. This is applicable when pxmPrimaryMuxClockSource is pxmServiceModuleClock1(2) or pxmServiceModuleClock2(6).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..32  

pxmSecondaryMuxClockSource 1.3.6.1.4.1.351.110.3.16.4
This object identifies the source of the Secondary Mux Clock for PXM card.
Status: current Access: read-only
OBJECT-TYPE    
  CmpClockSourceType  

pxmSecondaryInbandClockSourceLineNumber 1.3.6.1.4.1.351.110.3.16.5
This object indicates the inband line number. This is applicable when pxmSecondaryMuxClockSource is pxmInbandClock1(1) or pxmServiceModuleClock2 (5).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4  

pxmSecondarySMClockSourceSlotNumber 1.3.6.1.4.1.351.110.3.16.6
This object indicates the service module slot number. This is applicable when pxmSecondaryMuxClockSource is pxmServiceModuleClock1(2) or pxmServiceModuleClock2(6).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..32  

pxmCurrentClock 1.3.6.1.4.1.351.110.3.16.7
This object represents the clock source currently selected for PXM card. primary(1): The primary clock source is described by pxmPrimaryMuxClockSource secondary(2): The secondary clock source is described by pxmSecondaryMuxClockSource. intOscillator(3): Current clock is internal oscillator.
Status: current Access: read-only
OBJECT-TYPE    
  CmpCurrentClock  

pxmPreviousClock 1.3.6.1.4.1.351.110.3.16.8
This object represents the clock source previously selected for PXM card.
Status: current Access: read-only
OBJECT-TYPE    
  CmpCurrentClock  

pxmExtClockPresent 1.3.6.1.4.1.351.110.3.16.9
Status of External T1/E1 Clock on PXM card.
Status: current Access: read-only
OBJECT-TYPE    
  CmpClockExistence  

pxmExtClkSrcImpedance 1.3.6.1.4.1.351.110.3.16.10
Impedance on external clock input for PXM card.
Status: current Access: read-only
OBJECT-TYPE    
  CmpClockImpedance  

pxmExtClkConnectorType 1.3.6.1.4.1.351.110.3.16.11
This object describes the type of connector available for connecting the external clock source to the PXM.
Status: current Access: read-only
OBJECT-TYPE    
  CmpClockConnectorType  

pxmClkStratumLevel 1.3.6.1.4.1.351.110.3.16.12
This object describes the lowest stratum level provided by the interface the external clock source to the PXM back card.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER stratumUnknown(1), stratumLevel1(2), stratumLevel2(3), stratumLevel3E(4), stratumLevel3(5), stratumLevel4(6), stratumLevel4E(7)  

pxmClkErrReason 1.3.6.1.4.1.351.110.3.16.13
This object gives more information about clock status. The possible values are : goodClk(1) : Clock is good unkownReason(2) : reason not known noClkSignal(3) : Loss of signal(LOS) on clock source freqTooHigh(4) : frequency drifted too high freqTooLow(5) : frequency drifted too low excessiveJitter(6) : jitter has exceeded the tolerance missingCard (7) : no clock hardware found missingLogicalIf(8): Logical Interface missing or not operational noClock (9): No clock.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER goodClk(1), unknownReason(2), noClkSignal(3), freqTooHigh(4), freqTooLow(5), excessiveJitter(6), missingCard(7), missingLogicalIf(8), noClock(9)  

pxmExtClock2Present 1.3.6.1.4.1.351.110.3.16.14
This object indicates the status of external T1/E1 Clock on port 2 of PXMUI-S3 back card.
Status: current Access: read-only
OBJECT-TYPE    
  CmpClockExistence  

pxmExtClk2SrcImpedance 1.3.6.1.4.1.351.110.3.16.15
This object provides the impedance on external clock input on port 2 of PXMUI-S3 back card.
Status: current Access: read-only
OBJECT-TYPE    
  CmpClockImpedance  

pxmExtClk2ConnectorType 1.3.6.1.4.1.351.110.3.16.16
This object describes the type of connector available for connecting the external clock source to the port 2 of PXM-UI-S3 back card of PXM.
Status: current Access: read-only
OBJECT-TYPE    
  CmpClockConnectorType  

cmpClockMIBConformance 1.3.6.1.4.1.351.150.72.2
OBJECT IDENTIFIER    

cmpClockMIBGroups 1.3.6.1.4.1.351.150.72.2.1
OBJECT IDENTIFIER    

cmpClockMIBCompliances 1.3.6.1.4.1.351.150.72.2.2
OBJECT IDENTIFIER    

cmpClockCompliance 1.3.6.1.4.1.351.150.72.2.2.1
The compliance statement for objects related to PXM Clock mib.
Status: current Access: read-only
MODULE-COMPLIANCE    

cmpClockInfoGroup 1.3.6.1.4.1.351.150.72.2.1.1
The collection of objects which are used for providing information on PXM Clock configuration.
Status: current Access: read-only
OBJECT-GROUP    

cmpPrimaryClockInfoGroup 1.3.6.1.4.1.351.150.72.2.1.2
The collection of objects which are used for providing information on Primary Clock configuration.
Status: current Access: read-only
OBJECT-GROUP    

cmpSecondaryClockInfoGroup 1.3.6.1.4.1.351.150.72.2.1.3
The collection of objects which are used for providing information on Secondary Clock configuration.
Status: current Access: read-only
OBJECT-GROUP    

cmpExtClockInfoGroup 1.3.6.1.4.1.351.150.72.2.1.4
The collection of objects which are used for providing general information on PXM Clock configuration.
Status: current Access: read-only
OBJECT-GROUP