CISCO-LWAPP-WLAN-MIB

File: CISCO-LWAPP-WLAN-MIB.mib (165799 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
SNMP-FRAMEWORK-MIB INET-ADDRESS-MIB CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
Integer32 Gauge32 MODULE-COMPLIANCE
OBJECT-GROUP TimeStamp TruthValue
RowStatus DisplayString StorageType
MacAddress SnmpAdminString InetAddressType
InetAddress ciscoMgmt

Defined Types

CLWlanConfigEntry  
SEQUENCE    
  cLWlanIndex Unsigned32
  cLWlanRowStatus RowStatus
  cLWlanProfileName SnmpAdminString
  cLWlanSsid OCTET STRING
  cLWlanDiagChan TruthValue
  cLWlanStorageType StorageType
  cLWlanIsWired TruthValue
  cLWlanIngressInterface OCTET STRING
  cLWlanNACSupport TruthValue
  cLWlanWepKeyChange TimeStamp
  cLWlanChdEnable TruthValue
  cLWlan802dot11anDTIM Unsigned32
  cLWlan802dot11bgnDTIM Unsigned32
  cLWlanLoadBalancingEnable TruthValue
  cLWlanBandSelectEnable TruthValue
  cLWlanPassiveClientEnable TruthValue
  cLWlanReAnchorRoamedVoiceClientsEnable TruthValue
  cLWlanMulticastInterfaceEnable TruthValue
  cLWlanMulticastInterface SnmpAdminString
  cLWlanMulticastDirectEnable TruthValue
  cLWlanNACPostureSupport TruthValue
  cLWlanMaxClientsAccepted Unsigned32
  cLWlanScanDeferPriority BITS
  cLWlanScanDeferTime Unsigned32
  cLWlanLanSubType INTEGER
  cLWlanWebAuthOnMacFilterFailureEnabled TruthValue
  cLWlanStaticIpTunnelingEnabled TruthValue
  cLWlanKtsCacSupportEnabled TruthValue
  cLWlanWifiDirectPolicyStatus INTEGER
  cLWlanWebAuthIPv6AclName DisplayString
  cLWlanHotSpot2Enabled TruthValue
  cLWlanMaxClientsAllowedPerRadio Unsigned32
  cLWlanDhcpDeviceProfiling TruthValue
  cLWlanMacAuthOverDot1xEnabled TruthValue
  cLWlanUserTimeout Unsigned32
  cLWlanUserIdleThreshold Unsigned32
  cLWlanHttpDeviceProfiling TruthValue
  cLWlanHotSpotClearConfig INTEGER
  cLWlanRadiusAuthFourthServer DisplayString
  cLWlanRadiusAuthFifthServer DisplayString
  cLWlanRadiusAuthSixthServer DisplayString
  cLWlanRadiusAcctFourthServer DisplayString
  cLWlanRadiusAcctFifthServer DisplayString
  cLWlanRadiusAcctSixthServer DisplayString
  cLWlanSelfAnchorEnabled TruthValue
  cLWlanUniversalAdmin TruthValue
  cLWlan11acMuMimoEnabled TruthValue

CLWlan11uEntry  
SEQUENCE    
  cLWlan11uStatus TruthValue
  cLWlan11uInternetAccess TruthValue
  cLWlan11uNetworkType INTEGER
  cLWlan11uVenueGroup INTEGER
  cLWlan11uVenueType INTEGER
  cLWlan11uVenueName SnmpAdminString
  cLWlan11uHessid MacAddress
  cLWlan11uNetworkAuthType INTEGER
  cLWlan11uIpAddressAvailIpv4 INTEGER
  cLWlan11uIpAddressAvailIpv6 INTEGER

CLWlan11uOuiEntry  
SEQUENCE    
  cLWlan11uOuiIndex Unsigned32
  cLWlan11uOui OCTET STRING
  cLWlan11uOuiIsBeacon TruthValue
  cLWlan11uOuiRowStatus RowStatus
  cLWlan11uOuiStorageType StorageType

CLWlan11uRealmEntry  
SEQUENCE    
  cLWlan11uRealmIndex Unsigned32
  cLWlan11uRealmName SnmpAdminString
  cLWlan11uRealmRowStatus RowStatus

CLWlan11uRealmEapEntry  
SEQUENCE    
  cLWlan11uRealmEapIndex Unsigned32
  cLWlan11uRealmEapMethod INTEGER
  cLWlan11uRealmEapRowStatus RowStatus

CLWlan11uRealmEapAuthEntry  
SEQUENCE    
  cLWlan11uRealmEapAuthIndex Unsigned32
  cLWlan11uRealmEapAuthMethod INTEGER
  cLWlan11uRealmEapAuthParam INTEGER
  cLWlan11uRealmEapAuthCredentialType INTEGER
  cLWlan11uRealmEapAuthRowStatus RowStatus

CLWlan11uDomainEntry  
SEQUENCE    
  cLWlan11uDomainIndex Unsigned32
  cLWlan11uDomainName SnmpAdminString
  cLWlan11uDomainRowStatus RowStatus

CLWlan11u3gppEntry  
SEQUENCE    
  cLWlan11u3gppIndex Unsigned32
  cLWlan11u3gppCountryCode OCTET STRING
  cLWlan11u3gppNetworkCode OCTET STRING
  cLWlan11u3gppRowStatus RowStatus

CLWlanServiceAdvertisementEntry  
SEQUENCE    
  cLWlanServiceAdvertisementStatus TruthValue
  cLWlanServiceAdvertisementMsapServerIndex Unsigned32

CLWlanHotSpot2OperatorEntry  
SEQUENCE    
  cLWlanHotSpot2OperatorIndex Unsigned32
  cLWlanHotSpot2OperatorName SnmpAdminString
  cLWlanHotSpot2OperatorLanguage SnmpAdminString
  cLWlanHotSpot2OperatorRowStatus RowStatus

CLWlanHotSpot2PortConfigEntry  
SEQUENCE    
  cLWlanHotSpot2PortConfigIndex Unsigned32
  cLWlanHotSpot2PortConfigIpProtocol INTEGER
  cLWlanHotSpot2PortConfigPortNumber INTEGER
  cLWlanHotSpot2PortConfigStatus INTEGER
  cLWlanHotSpot2PortConfigRowStatus RowStatus

CLWlanHotSpot2ConfigEntry  
SEQUENCE    
  cLWlanHotSpot2WanLinkStatus INTEGER
  cLWlanHotSpot2WanSymLinkStatus INTEGER
  cLWlanHotSpot2WanDownLinkSpeed Unsigned32
  cLWlanHotSpot2WanUpLinkSpeed Unsigned32

CLAPGroupsHyperlocationConfigEntry  
SEQUENCE    
  cLAPGroupsHyperlocationEnable TruthValue
  cLAPGroupsPakRssiThreshold Integer32
  cLAPGroupsPakRssiThresholdTrigger Gauge32
  cLAPGroupsPakRssiNtpIpAddressType InetAddressType
  cLAPGroupsPakRssiNtpAddress InetAddress

CLAPGroupsPortConfigEntry  
SEQUENCE    
  cLAPGroupsLANPortNumber Unsigned32
  cLAPGroupsLANPortStatus INTEGER
  cLAPGroupsLANPortPoeStatus INTEGER
  cLAPGroupsLANPortRlanName SnmpAdminString
  cLAPGroupsLANPortRowStatus RowStatus

CLAPGroupsExtModuleConfigEntry  
SEQUENCE    
  cLAPGroupsExtModuleStatus INTEGER
  cLAPGroupsExtModuleRlanName SnmpAdminString

CLAPGroupsVlanConfigEntry  
SEQUENCE    
  cLAPGroupName OCTET STRING
  cLAPGroupsVlanMappingInterfaceName OCTET STRING
  cLAPGroupNACSupport TruthValue
  cLAPGroupsVlanConfigRowStatus RowStatus
  cLAPGroupsVlanConfigStorageType StorageType
  cLAPGroupsWlanOrderIndex Unsigned32
  cLAPGroupsVlanMappingInterfaceNameRev1 OCTET STRING

CLAPGroupsVenueConfigEntry  
SEQUENCE    
  cLAPGroupsVenueConfigVenueGroup INTEGER
  cLAPGroupsVenueConfigVenueType INTEGER
  cLAPGroupsVenueConfigVenueName SnmpAdminString
  cLAPGroupsVenueConfigLanguage SnmpAdminString
  cLAPGroupsOperatingClass BITS

CLAPGroupsMultipleVenueEntry  
SEQUENCE    
  cLAPGroupsMultipleVenueLanguage SnmpAdminString
  cLAPGroupsMultipleVenueName SnmpAdminString
  cLAPGroupsMultipleVenueRowStatus RowStatus

CLWlanConfigClientEntry  
SEQUENCE    
  cLWlanClientAclName DisplayString
  cLWlanP2PBlocking INTEGER
  cLWlanClientIPv6AclName DisplayString

CLWlanConfigQosEntry  
SEQUENCE    
  cLWlanClientDSAverageDataRate Unsigned32
  cLWlanClientUSAverageDataRate Unsigned32
  cLWlanClientDSBurstDataRate Unsigned32
  cLWlanClientUSBurstDataRate Unsigned32
  cLWlanClientDSAvgRealTimeDataRate Unsigned32
  cLWlanClientUSAvgRealTimeDataRate Unsigned32
  cLWlanClientDSBurstRealTimeDataRate Unsigned32
  cLWlanClientUSBurstRealTimeDataRate Unsigned32
  cLWlanSsidDSAverageDataRate Unsigned32
  cLWlanSsidUSAverageDataRate Unsigned32
  cLWlanSsidDSBurstDataRate Unsigned32
  cLWlanSsidUSBurstDataRate Unsigned32
  cLWlanSsidDSAvgRealTimeDataRate Unsigned32
  cLWlanSsidUSAvgRealTimeDataRate Unsigned32
  cLWlanSsidDSBurstRealTimeDataRate Unsigned32
  cLWlanSsidUSBurstRealTimeDataRate Unsigned32

CLWlanConfigIosEntry  
SEQUENCE    
  cLWlanIosAccountingMethodListName SnmpAdminString
  cLWlanIosAuthenticationMethodListName SnmpAdminString
  cLWlanIosMacFilteringMethodListName SnmpAdminString
  cLWlanIosWebAuthMethodListName SnmpAdminString
  cLWlanIosQosUpStreamProfileName SnmpAdminString
  cLWlanIosQosDownStreamProfileName SnmpAdminString
  cLWlanIngressDHCPOption82Format Unsigned32
  cLWlanIngressDHCPOption82Ascii TruthValue
  cLWlanIngressDHCPOption82Rid TruthValue
  cLWlanIngressDHCPOption82Enable TruthValue
  cLWlanIosScanDeferPriority Unsigned32
  cLWlanIosWebAuthParameterMapName SnmpAdminString
  cLWlanIosQosClientUpStreamProfileName SnmpAdminString
  cLWlanIosQosClientDownStreamProfileName SnmpAdminString

CLWlanFlexibleNetflowEntry  
SEQUENCE    
  cLWlanFlexibleNetflowPolicyTypeIndex INTEGER
  cLWlanFlexibleNetflowMonitorName SnmpAdminString
  cLWlanFlexibleNetflowRowStatus RowStatus

Defined Values

ciscoLwappWlanMIB 2.1.9.9.512
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. This MIB helps to manage the WLANs on the controller. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected to. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the controllers. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Access Control List ( ACL ) A list of rules used to restrict the traffic reaching an interface or the CPU or WLAN. Each ACL is an ordered set of rules and actions. If a rule matches then the action for that rule is applied to the packet. 802.1x The IEEE ratified standard for enforcing port based access control. This was originally intended for use on wired LANs and later extended for use in 802.11 WLAN environments. This defines an architecture with three main parts - a supplicant (Ex. an 802.11 wireless client), an authenticator (the AP) and an authentication server(a Radius server). The authenticator passes messages back and forth between the supplicant and the authentication server to enable the supplicant get authenticated to the network. Temporal Key Integrity Protocol ( TKIP ) A security protocol defined to enhance the limitations of WEP. Message Integrity Check and per-packet keying on all WEP-encrypted frames are two significant enhancements provided by TKIP to WEP. Cisco Key Integrity Protocol ( CKIP ) A proprietary implementation similar to TKIP. CKIP implements key permutation for protecting the CKIP key against attacks. Other features of CKIP include expansion of encryption key to 16 bytes of length for key protection and MIC to ensure data integrity. Wired Equivalent Privacy ( WEP ) A security method defined by 802.11. WEP uses a symmetric key stream cipher called RC4 to encrypt the data packets. Wi-Fi Protected Access ( WPA ) Wi-Fi Protected Access (WPA and WPA2) are security systems created in response to several serious weaknesses found in Wired Equivalent Privacy (WEP). WPA implements the majority of the IEEE 802.11i standard, and was intended as an intermediate measure to take the place of WEP while 802.11i was prepared. WPA is designed to work with all wireless network interface cards, but not necessarily with first generation wireless access points. WLAN Layer 2 Security WLAN layer 2 (MAC) security defines the encryption and authentication approaches such as 802.1x, WPA, WPA2, CKIP and WEP. Delivery Traffic Indication Map ( DTIM ) DTIM is measured in beacon intervals and is the time period during which multicast/broadcast packets are sent to clients. This helps client to go in Power Saving mode and helps to save battery power. Network Admission Control (NAC) Cisco NAC uses the network infrastructure to enforce security policy compliance on all devices that seek to access network computing resources. With the Cisco NAC appliance, network administrators can authenticate, authorize, evaluate, and remediate wired, wireless, and remote users and their machines prior to network access. The Cisco NAC appliance identifies whether networked devices such as laptops, IP phones, or game consoles are compliant with network security policies, and repairs any vulnerabilities before it permits access to the network. Out of Band (OOB) Out-of-band deployments require user traffic to traverse through the NAC appliance only within authentication, posture assessment, and remediation. When a user is authenticated and passes all policy checks, the traffic is switched normally through the network and bypasses the NAC server. Band Select The 2.4 GHz band is congested and clients have to contend with numerous performance challenges. These consist of interference from Bluetooth, microwave ovens, cordless phones, etc.; protection mechanisms from 802.11b legacy clients; and co-channel interference from other access points due to 802.11bg?s limit of three non-overlapping channels. Allowing client Wi-Fi radios capable of dual band (2.4 and 5 GHz) operation move to the less congested 5 GHz radios would improve the overall performance of the network. The Band Select algorithm is based on probe response suppression on clients 2.4G radio. The feature is OFF by default and has to be manually switched ON globally for a WLC. It can be optionally over-ridden per-SSID to disallow it. Network Access Identifier ( NAI ) In order to provide roaming services, it is necessary to have a standardized method for identifying users. NAI is actually the user identity submitted by the client during network authentication. KTS (Key Telephone System) Key Telephone System is an alternative to a private branch exchange (PBX)phone system. A KTS is equipped with several buttons that allow a caller to directly select outgoing lines or incoming calls, and use intercom and conference facilities. HALO (Hyperlocation) Hyperlocation is a technique of calculating location using Angle of Arrival(AoA) tracks 802.11 OFDM clients (meaning 802.11a/g/n/ac clients) that are associated(connected) on the network and is able to do so with much higher accuracy than conventional Real Time Location Systems(RTLS) that rely on only RSSI (RF Signal Strength). PakRSSI (Packet Received Signal Strength Indicator) PakRSSI is a measurement of the power present in a received radio signal. POE (Power Over Ethernet) Power over Ethernet or PoE describes any of several standardized or ad-hoc systems which pass electrical power along with data on Ethernet cabling. This allows a single cable to provide both data connection and electrical power to devices such as wireless access points or IP cameras. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol [3] IEEE 802.11 - The original 1 Mbit/s and 2 Mbit/s, 2.4 GHz RF and IR standard.
MODULE-IDENTITY    

ciscoLwappWlanMIBNotifs 2.1.9.9.512.0
OBJECT IDENTIFIER    

ciscoLwappWlanMIBObjects 2.1.9.9.512.1
OBJECT IDENTIFIER    

ciscoLwappWlanMIBConform 2.1.9.9.512.2
OBJECT IDENTIFIER    

ciscoLwappWlanConfig 2.1.9.9.512.1.1
OBJECT IDENTIFIER    

ciscoLwappAPGroupsVlanConfig 2.1.9.9.512.1.2
OBJECT IDENTIFIER    

ciscoLwappWlan11uConfig 2.1.9.9.512.1.3
OBJECT IDENTIFIER    

ciscoLwappWlanServiceAdvertisementConfig 2.1.9.9.512.1.4
OBJECT IDENTIFIER    

ciscoLwappWlanHotSpot2Config 2.1.9.9.512.1.5
OBJECT IDENTIFIER    

ciscoLwappAPGroupsHyperlocationConfig 2.1.9.9.512.1.8
OBJECT IDENTIFIER    

ciscoLwappAPGroupsPortConfig 2.1.9.9.512.1.9
OBJECT IDENTIFIER    

cLWlanConfigTable 2.1.9.9.512.1.1.1
This table represents the WLAN configuration sent by the controller to the LWAPP APs for their operation. LWAPP APs exchange configuration messages with the controller and get the required configuration for their 802.11 related operations. As part of these messages, the WLAN configuration is pushed by the controller to the LWAPP APs. This table doesn't have any dependencies on other existing tables. By defining cLWlanIndex, the unique identifier for a WLAN, this table provides a common index structure for use in several other new tables that populate information on security related attributes like authentication, encryption, 802.11 parameters, Quality-of-Service attributes etc., that would relate to a particular WLAN. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLWlanRowStatus object.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlanConfigEntry

cLWlanConfigEntry 2.1.9.9.512.1.1.1.1
Each entry in this table represents the WLAN configuration sent by the controller to LWAPP APs for use during their operations. entries can be added/deleted by explicit management actions by NMS or by user console
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlanConfigEntry  

cLWlanIndex 2.1.9.9.512.1.1.1.1.1
This object uniquely identifies one instance of a WLAN on the controller. The value 513-517 indicates wired clients.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..517  

cLWlanRowStatus 2.1.9.9.512.1.1.1.1.2
This is the status column for this row and used to create, modify and delete specific instances of rows in this table. This table supports modification of writable objects when the RowStatus is 'active'. The following objects are mandatory for successful creation of an entry: cLWlanProfileName cLWlanSsid.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLWlanProfileName 2.1.9.9.512.1.1.1.1.3
This object represents the profile name assigned to this WLAN. The name assigned to a WLAN has to be unique across all the WLANs on the controller. An administrator can assign a meaningful name that could later be used to refer a particular WLAN on the controller. This object cannot be modified when cLWlanRowStatus is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..64)  

cLWlanSsid 2.1.9.9.512.1.1.1.1.4
This object represents the SSID assigned to this WLAN. The access points will broadcast this SSID on this WLAN. Different WLAN could use the same SSID as long as the layer 2 security is different. This object cannot be modified when cLWlanRowStatus is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

cLWlanDiagChan 2.1.9.9.512.1.1.1.1.5
This object is used to configure this WLAN as a diagnostic WLAN. A value of 'true' indicates that the WLAN can be used for diagnostic purposes. A value of 'false' indicates that the WLAN can not be used for diagnostic purposes.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanStorageType 2.1.9.9.512.1.1.1.1.6
This object represnts the storage type for this conceptual row.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cLWlanIsWired 2.1.9.9.512.1.1.1.1.7
This object is used to configure this WLAN as a wired or wireless WLAN. A value of 'true' indicates that this is a wired WLAN. A value of 'false' indicates that this is a wireless WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanIngressInterface 2.1.9.9.512.1.1.1.1.8
This object represents the ingress interface attached to the wireless lan.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

cLWlanNACSupport 2.1.9.9.512.1.1.1.1.9
This object is used to configure the NAC- Out Of Band(OOB) support for the WLAN. A value of 'true' indicates that the WLAN supports the NAC- Out Of Band(OOB) feature. A value of 'false' indicates that the WLAN does not support the NAC- Out Of Band(OOB) feature.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanWepKeyChange 2.1.9.9.512.1.1.1.1.10
This object represents the time when the static WEP key was changed by the user.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cLWlanChdEnable 2.1.9.9.512.1.1.1.1.11
This object indicates whether Coverage Hole Detection (CHD) is enabled on the controller. A value of 'true' indicates CHD is on and a value of 'false' indicates CHD is turned off for this WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlan802dot11anDTIM 2.1.9.9.512.1.1.1.1.12
This object represents DTIM configuration per WLAN for each 802.11 network. The DTIM value is measured in Beacon Intervals.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..255  

cLWlan802dot11bgnDTIM 2.1.9.9.512.1.1.1.1.13
This object represents DTIM configuration per WLAN for each 802.11 network. The DTIM value is measured in Beacon Intervals.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..255  

cLWlanLoadBalancingEnable 2.1.9.9.512.1.1.1.1.14
This object indicates whether Load Balancing is enabled on the controller for this WLAN . A value of 'true' indicates Load Balance is on and a value of 'false' indicates Load Balance is turned off for this WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanBandSelectEnable 2.1.9.9.512.1.1.1.1.15
This object indicates whether Band Select is enabled on the controller for this WLAN. A value of 'true' indicates Band Select is on and a value of 'false' indicates Band Select is turned off for this WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanPassiveClientEnable 2.1.9.9.512.1.1.1.1.16
This object specifies whether passive client is enabled on the controller for this WLAN. A value of 'true' indicates passive client is on and a value of 'false' indicates passive client is turned off for this WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanReAnchorRoamedVoiceClientsEnable 2.1.9.9.512.1.1.1.1.17
This object specifies whether the Roamed Voice Client Re-Anchoring feature is enabled on the controller for this WLAN. A value of 'true' indicates the roamed voice clients will get re-anchored. A value of 'false' indicates the roamed voice clients re-anchoring is turned off for this WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanMulticastInterfaceEnable 2.1.9.9.512.1.1.1.1.18
This object specifies whether multicast interface is enabled on the controller. A value of 'true' indicates that multicast interface feature is enabled and the interface represented by 'cLWlanMulticastInterface' would be used for the multicast traffic on this WLAN. A value of 'false' indicates that multicast interface feature is turned off for this WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanMulticastInterface 2.1.9.9.512.1.1.1.1.19
This object specifies the interface, which would be used for the multicast traffic for all the clients that are associated to this WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

cLWlanMulticastDirectEnable 2.1.9.9.512.1.1.1.1.20
This object specifies whether multicast direct is enabled on the controller for this WLAN. A value of 'true' indicates multicast direct is ON. A value of 'false' indicates multicast direct is turned off for this WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanNACPostureSupport 2.1.9.9.512.1.1.1.1.21
This object is used to configure the NAC-Posture support for the WLAN. A value of 'true' indicates that the WLAN supports the NAC-Posture feature. A value of 'false' indicates that the WLAN does not support the NAC-Posture feature.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanMaxClientsAccepted 2.1.9.9.512.1.1.1.1.22
This object specifies the maximum number of client connection allowed for this WLAN. A value of 0 indicates that there is no limit on maximum allowed clients for this WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLWlanScanDeferPriority 5.6.2.1.9.9.512.1.1.1.1.23
This object specifies the priority of packets that defer the off-channel scan. This is used in off-channel scanning to improve performance for medical devices using Radio Resource Management. Each bit represents a packet type for which off-channel scanning needs to be deferred. bit0 - Best effort. bit1 - Background bit2 - Spare bit3 - Excellent effort bit4 - Controlled load bit5 - Video, less than 100-ms latency and jitter bit6 - Voice, less than 10-ms latency and jitter bit7 - Network control
Status: current Access: read-create
OBJECT-TYPE    
  BITS bit0(0), bit1(1), bit2(2), bit3(3), bit4(4), bit5(5), bit6(6), bit7(7)  

cLWlanScanDeferTime 2.1.9.9.512.1.1.1.1.24
This object specifies the minimum number of milliseconds that must elapse without the appearance of a specified packet before the access point radios begin an off-channel scan.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..60000  

cLWlanLanSubType 2.1.9.9.512.1.1.1.1.25
This object specifies the sub-type of the LAN created. This has to be congruent with cLWlanIswired. If cLWlanIswired is set to 'true', allowed values are guestLan(2) and remoteLan(3). If cLWlanIswired is set to 'false', allowed value is wirelessLan(1). A value of other(4) will be returned if it doesnt match any values defined here. This value is not configurable.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER wirelessLan(1), guestLan(2), remoteLan(3), other(4)  

cLWlanWebAuthOnMacFilterFailureEnabled 2.1.9.9.512.1.1.1.1.26
This object is used to configure the Web based authentication on Mac Filter failure support for the WLAN. A value of 'true' enables Web authentication on MAC filter failure for the WLAN. A value of 'false' disables Web authentication on MAC filter failure for the WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanStaticIpTunnelingEnabled 2.1.9.9.512.1.1.1.1.27
This object is used to configure the Static IP Tunneling of clients feature support for the WLAN. A value of 'true' enables static IP Tunneling of client for the WLAN. A value of 'false' disables static IP Tunneling of client for the WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanKtsCacSupportEnabled 2.1.9.9.512.1.1.1.1.28
This object is used to configure the KTS CAC support for the WLAN. A value of 'true' enables the KTS based CAC support for this wlan. A value of 'false' disables the KTS based CAC support for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanWifiDirectPolicyStatus 2.1.9.9.512.1.1.1.1.29
This object is used to allow/disallow wi-fi direct clients to/from joining the infrastructure network. disable(1) - WFD is completely disabled. allow(2) - allow WFD clients disallow(3) - controller rejects association request from WFD clients only if it has P2P IE with concurrency enabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), allow(2), notAllow(3)  

cLWlanWebAuthIPv6AclName 2.1.9.9.512.1.1.1.1.30
This object represents the name of the Web Auth IPv6 ACL applied to this WLAN. If it is required to remove the ACL name for a WLAN, it should be set to 'none'. ACL's are applied in the following priority order - interfaces ACLs, WLAN ACLs, client ACLs.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

cLWlanHotSpot2Enabled 2.1.9.9.512.1.1.1.1.31
This object represents the hotSpot2 feature for this WLAN. A value of 'true' enables the HotSpot2 for this wlan. A value of 'false' disables the HotSpot2 for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanMaxClientsAllowedPerRadio 2.1.9.9.512.1.1.1.1.32
This object represents the maximum allowed clients per AP radio for a WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..200  

cLWlanDhcpDeviceProfiling 2.1.9.9.512.1.1.1.1.33
This object specifies the status of DHCP Device Profiling feature for this WLAN. A value of 'true' enables DHCP Device Profiling on this wlan. A value of 'false' disables DHCP the Device Profiling on this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanMacAuthOverDot1xEnabled 2.1.9.9.512.1.1.1.1.34
This object specifies the configuration state of authentication failover to Dot1x for the WLAN. A value of 'true' enables mac auth or dot1x for the WLAN. A value of 'false' disables mac auth or dot1x for the WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanUserTimeout 2.1.9.9.512.1.1.1.1.35
This object represents the timeout value of user for a WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLWlanUserIdleThreshold 2.1.9.9.512.1.1.1.1.36
This object represents the user idle threshold value in bytes for a WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLWlanHttpDeviceProfiling 2.1.9.9.512.1.1.1.1.37
This object specifies the status of HTTP Device Profiling feature for this WLAN. A value of 'true' enables HTTP Device Profiling on this wlan. A value of 'false' disables the HTTP Device Profiling on this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanHotSpotClearConfig 2.1.9.9.512.1.1.1.1.38
This object is used to clear all the configuration related to HotSpot feature at WLAN level. A value of 'enable' would clear the configuration. When queries for the current value, always 'disable' would be returned.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

cLWlanRadiusAuthFourthServer 2.1.9.9.512.1.1.1.1.39
This object specifies the Fourth Radius Authentication Server for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..21)  

cLWlanRadiusAuthFifthServer 2.1.9.9.512.1.1.1.1.40
This object specifies the Fifth Radius Authentication Server for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..21)  

cLWlanRadiusAuthSixthServer 2.1.9.9.512.1.1.1.1.41
This object specifies the Sixth Radius Authentication Server for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..21)  

cLWlanRadiusAcctFourthServer 2.1.9.9.512.1.1.1.1.42
This object specifies the Fourth Radius Accounting Server for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..21)  

cLWlanRadiusAcctFifthServer 2.1.9.9.512.1.1.1.1.43
This object specifies the Fifth Radius Accounting Server for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..21)  

cLWlanRadiusAcctSixthServer 2.1.9.9.512.1.1.1.1.44
This object specifies the Sixth Radius Accounting Server for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..21)  

cLWlanSelfAnchorEnabled 2.1.9.9.512.1.1.1.1.64
This object specifies whether self anchoring is enabled for the wlan.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanUniversalAdmin 2.1.9.9.512.1.1.1.1.65
This object allows universal admin mode. to be enabled on a 802.1X/WPA/WPA2 secured WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlan11acMuMimoEnabled 2.1.9.9.512.1.1.1.1.66
This object is used to configure 11ac Mu Mimo mode for the WLAN. A value of 'true' enables Mu Mimo mode for the WLAN. A value of 'false' disables Mu Mimo mode for the WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlan11uTable 2.1.9.9.512.1.3.1
This table represents the generic 802.11u configuration for a particular WLAN in a controller. This table has a one-to-one relationship with cLWlanConfigTable. There exist a row in this table corresponding to each row representing a WLAN in cLWlanConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlan11uEntry

cLWlan11uEntry 2.1.9.9.512.1.3.1.1
Each entry in this table represents the generic 802.11u configuration for a WLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlan11uEntry  

cLWlan11uStatus 2.1.9.9.512.1.3.1.1.1
This object is used to configure the 802.11u support for this WLAN. A value of 'true' indicates that 802.11u support is enabled for this WLAN and a value of 'false' indicates that the support is disabled for this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLWlan11uInternetAccess 2.1.9.9.512.1.3.1.1.2
This object is used to configure the internet access with respect to 802.11u feature for this WLAN. A value of 'true' indicates that internet access is enabled for this WLAN and a value of 'false' indicates that the internet access is disabled for this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLWlan11uNetworkType 2.1.9.9.512.1.3.1.1.3
This object indicates the network type with respect to 802.11u feature , for this WLAN. invalid (1) : Invalid network type. private(2) : Non-authorized users are not permitted on this network. privateWithGuestAccess(3) : Private network but guest accounts area available. chargeablePublicNetwork(4) : The network is accessible to anyone, however, access to the network requires payment. freePublicNetwork(5) : The network is accessible to anyone and no charges apply for the network use. testOrEquipment(6) : The network is used for test or experimental purposes only. wildcard(6) : Wildcard network type. personnalDeviceNetwork(8) : The network is accessible only by Personnal Device. emgerencyServiceOnlyNetwork(9) : Emergency Service network Type.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), private(2), privateWithGuestAccess(3), chargeablePublicNetwork(4), freePublicNetwork(5), testOrEquipment(6), wildcard(7), personnalDeviceNetwork(8), emgerencyServiceOnlyNetwork(9), notConfigured(255)  

cLWlan11uVenueGroup 2.1.9.9.512.1.3.1.1.4
This object indicates the venue group with respect to 802.11u feature , for this WLAN.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER unspecified(1), assembly(2), business(3), educational(4), factoryAndIndustrial(5), institutional(6), mercantile(7), residential(8), storage(9), utilityAndMisc(10), vehicular(11), outdoor(12)  

cLWlan11uVenueType 2.1.9.9.512.1.3.1.1.5
This object indicates the venue type within a particular venue group, with respect to 802.11u feature , for this WLAN. The Venue group-Venue Type relationship is per the following table: Venue Group Venue Type Code Venue Description =========== =============== ================= 0 0 Unspecified 0 1-255 Reserved 1 0 Unspecified Assembly 1 1 Arena 1 2 Stadium 1 3 Passenger Terminal (e.g., airport, port, bus station, ferry terminal, train station) 1 4 Amphitheater 1 5 Amusement Park 1 6 Place of Worship 1 7 Convention Center 1 8 Library 1 9 Museum 1 10 Restaurant 1 11 Theater 1 12 Bar 1 13 Coffee Shop 1 14 Zoo or Aquarium 1 15 Emergency Coordination Center 1 16-255 Reserved 2 0 Unspecified Business 2 1 Doctor or Dentist office 2 2 Bank 2 3 Fire Station 2 4 Police Station 2 6 Post Office 2 7 Professional Office 2 8 Research and Development Facility 2 9 Attorney Office 2 10-255 Reserved 3 0 Unspecified Educational 3 1 School, Primary 3 2 School, Secondary 3 3 University or College 3 4-255 Reserved 4 0 Unspecified Factory and Industrial 4 1 Factory 4 2-255 Reserved 5 0 Unspecified Institutional 5 1 Hospital 5 2 Long-Term Care Facility (e.g., Nursing home, Hospice, etc.) 5 3 Alcohol and Drug Re-habilitation Center 5 4 Group Home 5 5 Prison or Jail 5 6-255 Reserved 6 0 Unspecified Mercantile 6 1 Retail Store 6 2 Grocery Market 6 3 Automotive Service Station 6 4-255 Reserved 7 0 Unspecified Residential 7 1 Hotel or Motel 7 2 Dormitory 7 3 Boarding House 7 4-255 Reserved 8 0-255 Reserved 9 0-255 Reserved 10 0 Unspecified Vehicular 10 1 Automobile or Truck 10 2 Airplane 10 3 Bus 10 4 Ferry 10 5 Ship or Boat 10 6 Train 10 7-255 Reserved 11 0 Unspecified Outdoor 11 1 Muni-mesh Network 11 2 City Park 11 3-255 Reserved
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER unspecified(1), assembly(2), business(3), educational(4), factoryAndIndustrial(5), institutional(6), mercantile(7), residential(8), storage(9), utilityAndMisc(10), vehicular(11), outdoor(12)  

cLWlan11uVenueName 2.1.9.9.512.1.3.1.1.6
This is the venue name defined for this WLAN with respect to 802.11u feature.
Status: deprecated Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(1..255)  

cLWlan11uHessid 2.1.9.9.512.1.3.1.1.8
This object is used to configure the Hessid for this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cLWlan11uNetworkAuthType 2.1.9.9.512.1.3.1.1.9
This object is used to configure the NetworkAuthType for a WLAN
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER acceptance(1), enrollment(2), redirection(3), dnsRedirection(4), notConfigured(5)  

cLWlan11uIpAddressAvailIpv4 2.1.9.9.512.1.3.1.1.10
This object represents the IPv4 Address Availability.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notAvailable(1), public(2), portRestricted(3), singleNATPrivate(4), doubleNATPrivate(5), portRestrictedAndSingleNATPrivate(6), portRestrictedAndDoubleNATPrivate(7), unKnown(8)  

cLWlan11uIpAddressAvailIpv6 2.1.9.9.512.1.3.1.1.11
This object represents the IPv6 Address Availability.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notAvailable(1), available(2), unKnown(3)  

cLWlan11uOuiTable 2.1.9.9.512.1.3.2
This table represents the OUI (organizational unique identifier) configuration for a particular WLAN. OUIs are assigned by IEEE. A WLAN can have up to 32 OUIs defined. OUI configuration per WLAN is required for the 802.11u feature to work. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLWlan11uOuiRowStatus object.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlan11uOuiEntry

cLWlan11uOuiEntry 2.1.9.9.512.1.3.2.1
Each entry in this table represents the OUI (organizational unique identifier) configuration for a particular WLAN. OUIs are assigned by IEEE. A WLAN can have up to 32 OUIs defined. OUI configuration per WLAN is required for the 802.11u feature to work.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlan11uOuiEntry  

cLWlan11uOuiIndex 2.1.9.9.512.1.3.2.1.1
This object uniquely identifies one instance of a OUI on a WLAN.Each WLAN can have up to 32 OUIs defined. Each OUI should be unique.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

cLWlan11uOui 2.1.9.9.512.1.3.2.1.2
The OUI field is a public OUI assigned by the IEEE. Each OUI identifies a roaming consortium (group of SSPs with inter-SSP roaming agreement) or a single SSP.WLAN can have up to 32 OUIs defined. Each OUI defined for a WLAN should be unique. For example the value for Cisco is 004096.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(6|10)  

cLWlan11uOuiIsBeacon 2.1.9.9.512.1.3.2.1.3
This object is used to configure this particular OUI as one of the beacon OUIs. Beacon can carry at most 3 OUIs. User should be able to select 0-3 OUIs (from the already configured OUIs for this WLAN). A value of 'true' indicates that this OUI would be carried in beacon. A value of 'false' indicates that this OUI is not a beacon OUI.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlan11uOuiRowStatus 2.1.9.9.512.1.3.2.1.4
Row Status for creation/deletion of a particular OUI entry in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLWlan11uOuiStorageType 2.1.9.9.512.1.3.2.1.5
This object represnts the storage type for this conceptual row.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cLWlan11uRealmTable 2.1.9.9.512.1.3.3
This table represents the realm (NAI) details per WLAN. In order to provide roaming services, it is necessary to have a standardized method for identifying users. NAI is the user identity submitted by the client during network authentication. Each realm entry should be unique.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlan11uRealmEntry

cLWlan11uRealmEntry 2.1.9.9.512.1.3.3.1
Each entry in this table represents the realm (NAI) configuration for a particular WLAN.A WLAN can have up to 32 realm defined
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlan11uRealmEntry  

cLWlan11uRealmIndex 2.1.9.9.512.1.3.3.1.1
This object specifies, one instance of a realm EAP entry (NAI) on a WLAN. Each realm entry should be unique.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..128  

cLWlan11uRealmName 2.1.9.9.512.1.3.3.1.2
This object represents the NAI name. In order to provide roaming services, it is necessary to have a standardized method for identifying users. NAI is the user identity submitted by the client during network authentication. In roaming, the purpose of the NAI is to identify the user as well as to assist in the routing of the authentication request. Please note that the NAI may not necessarily be the same as the user's e-mail address or the user identity submitted in an application layer authentication.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..128)  

cLWlan11uRealmRowStatus 2.1.9.9.512.1.3.3.1.3
Row Status for creation/deletion of a particular realm entry (NAI)from the table
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLWlan11uRealmEapTable 2.1.9.9.512.1.3.4
This table represents the EAP method configured per realm for a particular WLAN. A realm can have up to 4 EAP method defined. The EAP method supported are LEAP,PEAP,EAP-FAST and EAP-TLS.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlan11uRealmEapEntry

cLWlan11uRealmEapEntry 2.1.9.9.512.1.3.4.1
Each entry in this table represents the EAP method configured per realm for a particular WLAN. A realm can have up to 4 EAP method defined. The EAP method supported are LEAP,PEAP,EAP-FAST and EAP-TLS.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlan11uRealmEapEntry  

cLWlan11uRealmEapIndex 2.1.9.9.512.1.3.4.1.1
This object uniquely identifies one instance of a EAP entry configured per a realm for a particular WLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4  

cLWlan11uRealmEapMethod 2.1.9.9.512.1.3.4.1.2
This object represents the EAP method defined.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), leap(2), peap(3), eapTls(4), eapFast(5), eapSim(6), eapTtls(7), eapAka(8)  

cLWlan11uRealmEapRowStatus 2.1.9.9.512.1.3.4.1.3
Row Status for creation/deletion of a particular EAP entry from the table
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLWlan11uRealmEapAuthTable 2.1.9.9.512.1.3.5
This table represents the authentication method details configured per EAP method for particular realm. There can be up to 10 authentication configuration entries per EAP method.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlan11uRealmEapAuthEntry

cLWlan11uRealmEapAuthEntry 2.1.9.9.512.1.3.5.1
Each entry in this table represents the authentication method details configured per EAP method for particular realm. There can be up to 10 authentication configuration entries per EAP method.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlan11uRealmEapAuthEntry  

cLWlan11uRealmEapAuthIndex 2.1.9.9.512.1.3.5.1.1
This object uniquely identifies one instance of a auth entry configured per a EAP for a particular WLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..10  

cLWlan11uRealmEapAuthMethod 2.1.9.9.512.1.3.5.1.2
This object represents the authentication method defined.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER nonEapInnerAuthType(1), innerAuthEapType(2), credentialType(3), tunneledEapCredentialType(4)  

cLWlan11uRealmEapAuthParam 2.1.9.9.512.1.3.5.1.3
This object represents the authentication parameter defined for a particular authentication method. The Autentication Parameter and the Authentication Method relationship as follows Method Parameter Description =========== =============== ================= 1 1 Reserved 1 2 PAP 1 3 CHAP 1 4 MSCHAP 1 5 MSCHAPV2 2 6 LEAP 2 7 PEAP 2 8 EAP-TLS 2 9 EAP-FAST 2 10 EAP-SIM 2 11 EAP-TTLS 2 12 EAP-AKA 3 13 SIM 3 14 USIM 3 15 NFCSECURE 3 16 HARDWARE TOKEN 3 17 SOFT TOKEN 3 18 CERTIFICATE 3 19 USERNAME PASSWORD 3 20 RESERVED 3 21 Anonynous 3 22 Vendor Specific
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), pap(2), chap(3), mschap(4), mschapV2(5), leap(6), peap(7), eapTls(8), eapFast(9), eapSim(10), eapTtls(11), eapAka(12), sim(13), usim(14), nfcSecure(15), hardwareToken(16), softToken(17), certificate(18), usernamePassword(19), reserved(20), anonynous(21), vendorSpecific(22)  

cLWlan11uRealmEapAuthCredentialType 2.1.9.9.512.1.3.5.1.4
This is the credential type defined for a particular authentication method.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER sim(1), usim(2), nfcSecure(3), hardwareToken(4), softToken(5), certificate(6), usernamePassword(7), reserved(8), anonynous(9), vendorSpecific(10)  

cLWlan11uRealmEapAuthRowStatus 2.1.9.9.512.1.3.5.1.5
Row Status for creation/deletion of a particular auth entry from the table
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLWlan11uDomainTable 2.1.9.9.512.1.3.6
This table represents the Domain Entry configuration for a particular WLAN in a controller. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLWlan11uDomainRowStatus object
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlan11uDomainEntry

cLWlan11uDomainEntry 2.1.9.9.512.1.3.6.1
Each entry in this table represents the Domain configuration for a particular WLAN. A WLAN can have up to 10 domains defined.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlan11uDomainEntry  

cLWlan11uDomainIndex 2.1.9.9.512.1.3.6.1.1
This object uniquely identifies one instance of a Domain on a WLAN.Each WLAN can have up to 10 Domains defined. Each Domain should be unique.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..32  

cLWlan11uDomainName 2.1.9.9.512.1.3.6.1.2
This object represents the domain name for this particular Index.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..255)  

cLWlan11uDomainRowStatus 2.1.9.9.512.1.3.6.1.3
Row Status for creation/deletion of a particular Domain entry in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLWlan11u3gppTable 2.1.9.9.512.1.3.7
This table represents the 3gpp info configuration for a particular WLAN in a controller. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLWlan11u3gppRowStatus object
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlan11u3gppEntry

cLWlan11u3gppEntry 2.1.9.9.512.1.3.7.1
Each entry in this table represents the Domain configuration for a particular WLAN. A WLAN can have up to 32 operator defined.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlan11u3gppEntry  

cLWlan11u3gppIndex 2.1.9.9.512.1.3.7.1.1
This object uniquely identifies one instance of a 3gpp on a WLAN.Each WLAN can have up to 32 3gpps defined. Each 3gpp should be unique.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..32  

cLWlan11u3gppCountryCode 2.1.9.9.512.1.3.7.1.2
This is the Language defined for this 3gpp Index.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

cLWlan11u3gppNetworkCode 2.1.9.9.512.1.3.7.1.3
This is the Language defined for this 3gpp Index.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

cLWlan11u3gppRowStatus 2.1.9.9.512.1.3.7.1.4
Row Status for creation/deletion of a particular 3gpp entry in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLWlanServiceAdvertisementTable 2.1.9.9.512.1.4.1
This table represents the generic service advertisement configuration for a particular WLAN in a controller. This table has a one-to-one relationship with cLWlanConfigTable. There exist a row in this table corresponding to each row representing a WLAN in cLWlanConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlanServiceAdvertisementEntry

cLWlanServiceAdvertisementEntry 2.1.9.9.512.1.4.1.1
Each entry in this table represents the generic 802.11u configuration for a WLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlanServiceAdvertisementEntry  

cLWlanServiceAdvertisementStatus 2.1.9.9.512.1.4.1.1.1
This object represents the MSAP status for this WLAN. A value of true enables MSAP for this WLAN. A value of false disbales MSAP for this WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLWlanServiceAdvertisementMsapServerIndex 2.1.9.9.512.1.4.1.1.5
This object represents the Index for the MSAP Server.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..10  

cLWlanHotSpot2OperatorTable 2.1.9.9.512.1.5.1
This table represents the Operator configuration for a particular WLAN in a controller. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLWlanHotSpot2OperatorRowStatus object
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlanHotSpot2OperatorEntry

cLWlanHotSpot2OperatorEntry 2.1.9.9.512.1.5.1.1
Each entry in this table represents the Domain configuration for a particular WLAN. A WLAN can have up to 32 operator defined.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlanHotSpot2OperatorEntry  

cLWlanHotSpot2OperatorIndex 2.1.9.9.512.1.5.1.1.1
This object uniquely identifies one instance of a Operator on a WLAN.Each WLAN can have up to 32 Operators defined. Each Operator should be unique.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..32  

cLWlanHotSpot2OperatorName 2.1.9.9.512.1.5.1.1.2
This object represents the Operator name for this particular Index.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..255)  

cLWlanHotSpot2OperatorLanguage 2.1.9.9.512.1.5.1.1.3
This is the Language defined for this Operator Index.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..3)  

cLWlanHotSpot2OperatorRowStatus 2.1.9.9.512.1.5.1.1.4
Row Status for creation/deletion of a particular Operator entry in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLWlanHotSpot2PortConfigTable 2.1.9.9.512.1.5.2
This object uniquely identifies one instance of Port-Protocol Configuration on a WLAN.Each WLAN can have up to 10 port configuration defined.Each configuration should be unique.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlanHotSpot2PortConfigEntry

cLWlanHotSpot2PortConfigEntry 2.1.9.9.512.1.5.2.1
Each entry in this table represents the Port-Protocol configuration for a particular WLAN. A WLAN can have up to 10 port configurations defined.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlanHotSpot2PortConfigEntry  

cLWlanHotSpot2PortConfigIndex 2.1.9.9.512.1.5.2.1.1
This object uniquely identifies one instance of a Port Configuration on a WLAN.Each WLAN can have up to 32 Port Configurations defined.Each Port Configuration should be unique.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

cLWlanHotSpot2PortConfigIpProtocol 2.1.9.9.512.1.5.2.1.2
This object represents the Port Ip protocol for this index for a WLAN
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER icmp(1), ftp(6), ikev2(17), esp(50)  

cLWlanHotSpot2PortConfigPortNumber 2.1.9.9.512.1.5.2.1.3
This object represents the Port Number for this index for a WLAN. This object indicates the Port Number with respect to an IP Protocol. The Protocol Port Number relationship is per the following table: IP Protocol Port Number Description =========== =============== ================= 1 0 ICMP 6 20 FTP 6 22 SSH 6 443 TLS 6 1723 PPTP-VPN 6 5060 VoIP 17 5060 VoIP 17 4500 IKEv 17 500 IKEv2 50 0 ESP
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER icmp-esp(0), ftp(20), ssh(22), ttls-vpn(443), ikev2(500), pptp-vpn(1723), ipsec-nat(4500), voip(5060)  

cLWlanHotSpot2PortConfigStatus 2.1.9.9.512.1.5.2.1.4
This object represents the Port Status for this instance for a WLAN
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER closed(1), open(2), unknown(3)  

cLWlanHotSpot2PortConfigRowStatus 2.1.9.9.512.1.5.2.1.5
Row Status for creation/deletion of a particular PortConfig entry in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLWlanHotSpot2ConfigTable 2.1.9.9.512.1.5.3
This table represents the generic HotSpot2 configuration for a particular WLAN in a controller. This table has a one-to-one relationship with cLWlanConfigTable. There exist a row in this table corresponding to each row representing a WLAN in cLWlanConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlanHotSpot2ConfigEntry

cLWlanHotSpot2ConfigEntry 2.1.9.9.512.1.5.3.1
Each entry in this table represents the generic HotSpot2 configuration for a WLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlanHotSpot2ConfigEntry  

cLWlanHotSpot2WanLinkStatus 2.1.9.9.512.1.5.3.1.1
This object represents the status of the link with respect to WAN metrics configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER linkUp(1), linkDown(2), linkInTestState(3), notConfigured(4)  

cLWlanHotSpot2WanSymLinkStatus 2.1.9.9.512.1.5.3.1.2
This object represents the symmetry of the link with respect to WAN metrics configuration. A value of 'different(1)' indicates that link speed is different in uplink and downlink(ex:ADSL). A value of 'same(2)' indicates that link speed is same in uplink and downlink(ex:DSL).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER different(1), same(2)  

cLWlanHotSpot2WanDownLinkSpeed 2.1.9.9.512.1.5.3.1.3
This object represents the down link speed of WAN Backhaul in kbps.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanHotSpot2WanUpLinkSpeed 2.1.9.9.512.1.5.3.1.4
This object represents the up link speed of WAN Backhaul in kbps.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLAPGroupsHyperlocationConfigTable 2.1.9.9.512.1.8.1
A table for configuring Hyperlocation settings allowed for each AP Group. Each site can have a set of HALO and PakRSSI parameters associated with it.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLAPGroupsHyperlocationConfigEntry

cLAPGroupsHyperlocationConfigEntry 2.1.9.9.512.1.8.1.1
An entry in cLAPGroupsHyperlocationConfigEntry. cLAPGroupName is mandatory for creating an entry in CLAPGroupsHyperlocationConfigEntry .
Status: current Access: not-accessible
OBJECT-TYPE    
  CLAPGroupsHyperlocationConfigEntry  

cLAPGroupsHyperlocationEnable 2.1.9.9.512.1.8.1.1.1
This object represents the state of Hyperlocation. A value of 'true' indicates that Hyperlocation is enabled. A value of 'false' indicates that Hyperlocation is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLAPGroupsPakRssiThreshold 2.1.9.9.512.1.8.1.1.2
This object represents the threshold value for Packet RSSI location feature. Valid range is -100 dbm to -50 dbm.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cLAPGroupsPakRssiThresholdTrigger 2.1.9.9.512.1.8.1.1.3
This object represents the trigger threshold value for Packet RSSI location feature. Valid range is 1 dbm to 100 dbm.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32 1..100  

cLAPGroupsPakRssiNtpIpAddressType 2.1.9.9.512.1.8.1.1.4
This object represents the NTP server IP address type for Packet RSSI location feature.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

cLAPGroupsPakRssiNtpAddress 2.1.9.9.512.1.8.1.1.5
This object represents the NTP server IP address for Packet RSSI location feature.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

cLAPGroupsPortConfigTable 2.1.9.9.512.1.9.1
A table for configuring port settings allowed for each AP Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLAPGroupsPortConfigEntry

cLAPGroupsPortConfigEntry 2.1.9.9.512.1.9.1.1
An entry in cLAPGroupsPortConfigEntry. cLAPGroupName is mandatory for creating a entry in CLAPGroupsPortConfigEntry .
Status: current Access: not-accessible
OBJECT-TYPE    
  CLAPGroupsPortConfigEntry  

cLAPGroupsLANPortNumber 2.1.9.9.512.1.9.1.1.1
This object uniquely identifies the LAN port number of an AP Group. Each AP Group can have up to 3 LAN ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

cLAPGroupsLANPortStatus 2.1.9.9.512.1.9.1.1.2
This object represents the LAN port state. A value of 'true' indicates that selected LAN Port is enabled. A value of 'false' indicates that LAN Port is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

cLAPGroupsLANPortPoeStatus 2.1.9.9.512.1.9.1.1.3
This object represents the LAN port POE state. A value of 'true' indicates that POE is enabled. A value of 'false' indicates that POE is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER notsupported(0), disabled(1), enabled(2)  

cLAPGroupsLANPortRlanName 2.1.9.9.512.1.9.1.1.4
This object represents the remote LAN name of the corresponding port.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..64)  

cLAPGroupsLANPortRowStatus 2.1.9.9.512.1.9.1.1.5
This is the status column for this row and used to create and delete specific instances of rows in this table. cLAPGroupName and cLAPGroupsLANPortNumber are mandatory for creating and deleting an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLAPGroupsExtModuleConfigTable 2.1.9.9.512.1.9.2
A table for configuring external module settings allowed for each AP Group. An entry in this table is created for each AP group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLAPGroupsExtModuleConfigEntry

cLAPGroupsExtModuleConfigEntry 2.1.9.9.512.1.9.2.1
An entry in cLAPGroupsExtModuleConfigEntry. cLAPGroupName is mandatory for creating an entry in CLAPGroupsExtModuleConfigEntry .
Status: current Access: not-accessible
OBJECT-TYPE    
  CLAPGroupsExtModuleConfigEntry  

cLAPGroupsExtModuleStatus 2.1.9.9.512.1.9.2.1.1
This object represents the external module state. A value of 'true' indicates that external module is enabled. A value of 'false' indicates that external module is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

cLAPGroupsExtModuleRlanName 2.1.9.9.512.1.9.2.1.2
This object represents the remote lan name of the external module.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(1..64)  

cLAPGroupsVlanConfigTable 2.1.9.9.512.1.2.1
A table for the WLAN-interface-mappings and WLAN-NAC settings allowed for each configured site. Each site can have a set of WLANs associated with it. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLAPGroupsVlanConfigRowStatus object.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLAPGroupsVlanConfigEntry

cLAPGroupsVlanConfigEntry 2.1.9.9.512.1.2.1.1
An entry in cLAPGroupsVlanMappingTable. cLWlanProfileName is mandatory for creating a entry in cLWlanConfigEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLAPGroupsVlanConfigEntry  

cLAPGroupName 2.1.9.9.512.1.2.1.1.1
This object uniquely identifies a AP group. The string is an unique name assigned to a site.
Status: current Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(1..64)  

cLAPGroupsVlanMappingInterfaceName 2.1.9.9.512.1.2.1.1.2
This object represents the interface to be used when a client connects to the 'cLWlanProfileName' WLAN on the AP. When an AP is associated with a site, and the site has an associated set of WLANs, then only those WLANs are beamed by the AP. cLAPGroupsVlanMappingInterfaceName object is superseded by cLAPGroupsVlanMappingInterfaceNameRev1.
Status: deprecated Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

cLAPGroupNACSupport 2.1.9.9.512.1.2.1.1.3
This object is used to configure the NAC- Out Of Band(OOB) support for this AP groups VLAN. A value of 'true' indicates that the AP group supports the NAC- Out Of Band(OOB) feature. A value of 'false' indicates that the AP group does not support the NAC- Out Of Band(OOB) feature.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLAPGroupsVlanConfigRowStatus 2.1.9.9.512.1.2.1.1.4
This is the status column for this row and used to create and delete specific instances of rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLAPGroupsVlanConfigStorageType 2.1.9.9.512.1.2.1.1.5
This object represnts the storage type for this conceptual row.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cLAPGroupsWlanOrderIndex 2.1.9.9.512.1.2.1.1.6
This object represnts the position of a wlan in each AP group. When a WLAN is added to an AP group, it will be placed in the lowest available slot in an array of size 16. This index will determine the order in which the WLAN is applied on an AP in that group.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cLAPGroupsVlanMappingInterfaceNameRev1 2.1.9.9.512.1.2.1.1.7
This object represents the interface to be used when a client connects to the 'cLWlanProfileName' WLAN on the AP. When an AP is associated with a site, and the site has an associated set of WLANs, then only those WLANs are beamed by the AP.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..128)  

cLAPGroupsVenueConfigTable 2.1.9.9.512.1.2.2
A table for the configuring Venue details for a configured site.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLAPGroupsVenueConfigEntry

cLAPGroupsVenueConfigEntry 2.1.9.9.512.1.2.2.1
An entry in cLAPGroupsVlanMappingTable. cLWlanProfileName is mandatory for creating a entry in cLWlanConfigEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLAPGroupsVenueConfigEntry  

cLAPGroupsVenueConfigVenueGroup 2.1.9.9.512.1.2.2.1.1
This object indicates the venue group for this AP Group.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unspecified(1), assembly(2), business(3), educational(4), factoryAndIndustrial(5), institutional(6), mercantile(7), residential(8), storage(9), utilityAndMisc(10), vehicular(11), outdoor(12)  

cLAPGroupsVenueConfigVenueType 2.1.9.9.512.1.2.2.1.2
This object indicates the venue type within a particular venue group,for this AP Group. The Venue group-Venue Type relationship is per the following table: Venue Group Venue Type Code Venue Description =========== =============== ================= 0 0 Unspecified 0 1-255 Reserved 1 0 Unspecified Assembly 1 1 Arena 1 2 Stadium 1 3 Passenger Terminal (e.g., airport, port, bus station, ferry terminal, train station) 1 4 Amphitheater 1 5 Amusement Park 1 6 Place of Worship 1 7 Convention Center 1 8 Library 1 9 Museum 1 10 Restaurant 1 11 Theater 1 12 Bar 1 13 Coffee Shop 1 14 Zoo or Aquarium 1 15 Emergency Coordination Center 1 16-255 Reserved 2 0 Unspecified Business 2 1 Doctor or Dentist office 2 2 Bank 2 3 Fire Station 2 4 Police Station 2 6 Post Office 2 7 Professional Office 2 8 Research and Development Facility 2 9 Attorney Office 2 10-255 Reserved 3 0 Unspecified Educational 3 1 School, Primary 3 2 School, Secondary 3 3 University or College 3 4-255 Reserved 4 0 Unspecified Factory and Industrial Factory 4 2-255 Reserved 5 0 Unspecified Institutional 5 1 Hospital 5 2 Long-Term Care Facility (e.g., Nursing home, Hospice, etc.) 5 3 Alcohol and Drug Re-habilitation Center 5 4 Group Home 5 5 Prison or Jail 5 6-255 Reserved 6 0 Unspecified Mercantile 6 1 Retail Store 6 2 Grocery Market 6 3 Automotive Service Station 6 4-255 Reserved 7 0 Unspecified Residential 7 1 Hotel or Motel 7 2 Dormitory 7 3 Boarding House 7 4-255 Reserved 8 0-255 Reserved 9 0-255 Reserved 10 0 Unspecified Vehicular 10 1 Automobile or Truck 10 2 Airplane 10 3 Bus 10 4 Ferry 10 5 Ship or Boat 10 6 Train 10 7-255 Reserved 11 0 Unspecified Outdoor 11 1 Muni-mesh Network 11 2 City Park 11 3-255 Reserved
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unspecified(1), unspecifiedAssembly(2), arena(3), stadium(4), passengerTerminal(5), amphitheater(6), amusementPark(7), placeOfWorship(8), conventionCenter(9), library(10), museum(11), restaurant(12), theater(13), bar(14), coffeeShop(15), zooOrAquarium(16), emergencyCoordinationCenter(17), unspecifiedBusiness(18), doctorOrDentistOffice(19), bank(20), fireStation(21), policeStation(22), postOffice(23), professionalOffice(24), researchAndDevelopmentFacility(25), attorneyOffice(26), unspecifiedEducational(27), schoolPrimary(28), schoolSecondary(29), universityOrCollege(30), unspecifiedFactoryAndIndustrial(31), factory(32), unspecifiedInstitutional(33), hospital(34), longTermCareFacility(35), alcoholAndDrugRehabilitationCenter(36), groupHome(37), prisonOrJail(38), unspecifiedMercantile(39), retailStore(40), groceryMarket(41), atomotiveServiceStation(42), shoppingMall(43), gasStation(44), unspecifiedResidential(45), privateResidence(46), hotelOrMotel(47), dormitory(48), boardingHouse(49), unspecifiedStorage(50), unspecifiedUtility(51), unspecifiedVehicular(52), automobileOrTruck(53), airplane(54), bus(55), ferry(56), shipOrBoat(57), train(58), motorBike(59), unspecifiedOutdoor(60), muniMeshNetwork(61), cityPark(62), restArea(63), trafficControl(64), busStop(65), kiosk(66)  

cLAPGroupsVenueConfigVenueName 2.1.9.9.512.1.2.2.1.3
This is the venue name defined for this AP Group.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..252)  

cLAPGroupsVenueConfigLanguage 2.1.9.9.512.1.2.2.1.4
This is the Language defined for this AP Group.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..3)  

cLAPGroupsOperatingClass 2.1.9.9.512.1.2.2.1.5
This object specifies the the group of channels on the frequency band(s) the access network operates.
Status: current Access: read-write
OBJECT-TYPE    
  BITS class81(0), class83(1), class84(2), class112(3), class113(4), class115(5), class116(6), class117(7), class118(8), class119(9), class120(10), class121(11), class122(12), class123(13), class124(14), class125(15), class126(16), class127(17)  

cLAPGroupsMultipleVenueTable 2.1.9.9.512.1.2.3
Table for configuring multiple venues for a configured site.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLAPGroupsMultipleVenueEntry

cLAPGroupsMultipleVenueEntry 2.1.9.9.512.1.2.3.1
An entry in cLAPGroupsMultipleVenueTable. cLAPGroupsMultipleVenueLanguage is mandatory for creating a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLAPGroupsMultipleVenueEntry  

cLAPGroupsMultipleVenueLanguage 2.1.9.9.512.1.2.3.1.1
This is the Language defined for the particular venue name entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(0..3)  

cLAPGroupsMultipleVenueName 2.1.9.9.512.1.2.3.1.2
This is the one of the venue names defined for this AP Group.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..252)  

cLAPGroupsMultipleVenueRowStatus 2.1.9.9.512.1.2.3.1.3
Row Status for creation/deletion of a particular venue entry in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLWlanConfigClientTable 2.1.9.9.512.1.1.2
This table represents the WLAN configuration for the 802.11 wireless clients that are associated with the APs that have joined this controller. The creation of a new row in cLWlanConfigTable, through an explicit network management action, results in creation of an entry in this table. Similarly, deletion of a row in cLWlanConfigTable through user action causes the deletion of corresponding row in this table. This table has an one-to-one relationship with cLWlanConfigTable. There exists an entry in this table for each corresponding entry in the cLWlanConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlanConfigClientEntry

cLWlanConfigClientEntry 2.1.9.9.512.1.1.2.1
Each entry represents a conceptual row in this table and provides the information about the clients associated on the WLAN, uniquely identified by the cLWlanIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlanConfigClientEntry  

cLWlanClientAclName 2.1.9.9.512.1.1.2.1.1
This object represents the name of the ACL applied to this WLAN. If it is required to remove the ACL name for a WLAN, it should be set to 'none'. ACL's are applied in the following priority order - interfaces ACLs, WLAN ACLs, client ACLs.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

cLWlanP2PBlocking 2.1.9.9.512.1.1.2.1.2
This object represents per WLAN peer-to-peer blocking behavior on controller. Peer-to-peer blocking means traffic between two clients on same VLAN will not be bridged. disable : Peer-to-peer blocking is disabled and traffic is bridged locally within the controller. drop : The packet will be discarded. forwardUp : The packet will be forwarded on the upstream VLAN. The device 'north' of the controller can then make the decision about what to do with the packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), drop(2), forwardUp(3)  

cLWlanClientIPv6AclName 2.1.9.9.512.1.1.2.1.3
This object represents the name of the IPv6 ACL applied to this WLAN. If it is required to remove the ACL name for a WLAN, it should be set to 'none'. ACL's are applied in the following priority order - interfaces ACLs, WLAN ACLs, client ACLs.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

cLWlanConfigQosTable 2.1.9.9.512.1.1.3
This table represents the QoS configuration for the WLAN. The creation of a new row in cLWlanConfigTable, through an explicit network management action, results in creation of an entry in this table. Similarly, deletion of a row in cLWlanConfigTable through user action causes the deletion of corresponding row in this table. This table has an one-to-one relationship with cLWlanConfigTable. There exists an entry in this table for each corresponding entry in the cLWlanConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlanConfigQosEntry

cLWlanConfigQosEntry 2.1.9.9.512.1.1.3.1
Each entry represents a conceptual row in this table and provides the information about the QoS parameters on the WLAN, uniquely identified by the cLWlanIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlanConfigQosEntry  

cLWlanClientDSAverageDataRate 2.1.9.9.512.1.1.3.1.1
This object specifies Average Data Rate per user on downstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanClientUSAverageDataRate 2.1.9.9.512.1.1.3.1.2
This object specifies Average Data Rate per user on upstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanClientDSBurstDataRate 2.1.9.9.512.1.1.3.1.3
This object specifies Burst Data Rate per user on downstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanClientUSBurstDataRate 2.1.9.9.512.1.1.3.1.4
This object specifies Burst Data Rate per user on upstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanClientDSAvgRealTimeDataRate 2.1.9.9.512.1.1.3.1.5
This object specifies average real time Data Rate per user on downstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanClientUSAvgRealTimeDataRate 2.1.9.9.512.1.1.3.1.6
This object specifies average real time Data Rate per user on upstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanClientDSBurstRealTimeDataRate 2.1.9.9.512.1.1.3.1.7
This object specifies burst real time Data Rate per user on downstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanClientUSBurstRealTimeDataRate 2.1.9.9.512.1.1.3.1.8
This object specifies burst real time Data Rate per user on upstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanSsidDSAverageDataRate 2.1.9.9.512.1.1.3.1.9
This object specifies Average Data Rate per user on downstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanSsidUSAverageDataRate 2.1.9.9.512.1.1.3.1.10
This object specifies Average Data Rate per user on upstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanSsidDSBurstDataRate 2.1.9.9.512.1.1.3.1.11
This object specifies Burst Data Rate per user on downstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanSsidUSBurstDataRate 2.1.9.9.512.1.1.3.1.12
This object specifies Burst Data Rate per user on upstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanSsidDSAvgRealTimeDataRate 2.1.9.9.512.1.1.3.1.13
This object specifies average real time Data Rate per user on downstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanSsidUSAvgRealTimeDataRate 2.1.9.9.512.1.1.3.1.14
This object specifies average real time Data Rate per user on upstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanSsidDSBurstRealTimeDataRate 2.1.9.9.512.1.1.3.1.15
This object specifies burst real time Data Rate per user on downstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanSsidUSBurstRealTimeDataRate 2.1.9.9.512.1.1.3.1.16
This object specifies burst real time Data Rate per user on upstream. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanConfigIosTable 2.1.9.9.512.1.1.4
This table represents the WLAN configuration for IOS profiles configured on the switch. The creation of a new row in cLWlanConfigTable, through an explicit network management action, results in creation of an entry in this table. Similarly, deletion of a row in cLWlanConfigTable through user action causes the deletion of corresponding row in this table. This table has an one-to-one relationship with cLWlanConfigTable. There exists an entry in this table for each corresponding entry in the cLWlanConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlanConfigIosEntry

cLWlanConfigIosEntry 2.1.9.9.512.1.1.4.1
Each entry represents a conceptual row in this table and provides the information about the clients associated on the WLAN, uniquely identified by the cLWlanIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlanConfigIosEntry  

cLWlanIosAccountingMethodListName 2.1.9.9.512.1.1.4.1.1
This object represents the method list name used for accounting on this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

cLWlanIosAuthenticationMethodListName 2.1.9.9.512.1.1.4.1.2
This object represents the method list name used for 802.1x authentication on this WLAN. This could be LDAP, RADIUS, LOCAL AUTH.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

cLWlanIosMacFilteringMethodListName 2.1.9.9.512.1.1.4.1.3
This object represents the method list name used for mac filtering on this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

cLWlanIosWebAuthMethodListName 2.1.9.9.512.1.1.4.1.4
This object represents the method list name used for WEB AUTH on this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

cLWlanIosQosUpStreamProfileName 2.1.9.9.512.1.1.4.1.5
This object represents the profile name used for upstream QOS configuration on this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

cLWlanIosQosDownStreamProfileName 2.1.9.9.512.1.1.4.1.6
This object represents the profile name used for downstream QOS configuration on this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

cLWlanIngressDHCPOption82Format 2.1.9.9.512.1.1.4.1.7
This object represents the DHCP Option82 format for this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanIngressDHCPOption82Ascii 2.1.9.9.512.1.1.4.1.8
This object represents the DHCP Option82 Ascii option for this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLWlanIngressDHCPOption82Rid 2.1.9.9.512.1.1.4.1.9
This object represents the DHCP Option82 Rid option for this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLWlanIngressDHCPOption82Enable 2.1.9.9.512.1.1.4.1.10
This object represents the DHCP Option82 state for this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLWlanIosScanDeferPriority 2.1.9.9.512.1.1.4.1.11
This object specifies the priority of packets that defer the off-channel scan. This is used in off-channel scanning to improve performance for medical devices using Radio Resource Management. Each bit represents a packet type for which off-channel scanning needs to be deferred.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLWlanIosWebAuthParameterMapName 2.1.9.9.512.1.1.4.1.12
This object represents the web auth parameter name on this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

cLWlanIosQosClientUpStreamProfileName 2.1.9.9.512.1.1.4.1.13
This object represents the profile name used for upstream QOS client configuration on this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

cLWlanIosQosClientDownStreamProfileName 2.1.9.9.512.1.1.4.1.14
This object represents the profile name used for downstream QOS client configuration on this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

cLWlanFlexibleNetflowTable 2.1.9.9.512.1.1.5
This table represents the flexible netflow policy details per WLAN for AVC. The creation of a new row in cLWlanFlexibleConfigTable, through an explicit network management action, results in creation of an entry in this table. Similarly, deletion of a row in cLWlanConfigTable through user action causes the deletion of corresponding rows in this table. For each wlan, there will be zero to many instances of flexible netflow policies.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLWlanFlexibleNetflowEntry

cLWlanFlexibleNetflowEntry 2.1.9.9.512.1.1.5.1
Each entry represents a conceptual row in this table and provides the information about the flexible netflow policy types associated on the WLAN, uniquely identified by the cLWlanIndex and cLWlanFlexibleNetflowPolicyTypeIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLWlanFlexibleNetflowEntry  

cLWlanFlexibleNetflowPolicyTypeIndex 2.1.9.9.512.1.1.5.1.1
This object is used to set the netflow traffic direction for AVC. none(0) capture no traffic IPV4 Input Policy(1) - IPV4 input policy IPV4OutputPolicy(2) - IPV4 output policy IPV6InputPolicy(3) - IPV6 input policy IPV6OutputPolicy(4) - IPV6 output policy DatalinkInputPolicy(5) - Datalink input policy DatalinkOutputPolicy(6) - Datalink output policy.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(0), ipv4InputPolicy(1), ipv4OutputPolicy(2), ipv6InputPolicy(3), ipv6OutputPolicy(4), datalinkInputPolicy(5), datalinkOutputPolicy(6)  

cLWlanFlexibleNetflowMonitorName 2.1.9.9.512.1.1.5.1.2
This object represents the flexible netflow monitor name assigned to this WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

cLWlanFlexibleNetflowRowStatus 2.1.9.9.512.1.1.5.1.3
Row Status for creation/deletion of a particular flexible netflow policy entry from the table
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ciscoLwappWlanMIBCompliances 2.1.9.9.512.2.1
OBJECT IDENTIFIER    

ciscoLwappWlanMIBGroups 2.1.9.9.512.2.2
OBJECT IDENTIFIER    

ciscoLwappWlanMIBCompliance 2.1.9.9.512.2.1.1
The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module.
Status: deprecated Access: read-create
MODULE-COMPLIANCE    

ciscoLwappWlanMIBComplianceRev1 2.1.9.9.512.2.1.2
The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module.
Status: deprecated Access: read-create
MODULE-COMPLIANCE    

ciscoLwappWlanMIBComplianceRev2 2.1.9.9.512.2.1.3
The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module.
Status: deprecated Access: read-create
MODULE-COMPLIANCE    

ciscoLwappWlanMIBComplianceRev3 2.1.9.9.512.2.1.4
The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module.
Status: deprecated Access: read-create
MODULE-COMPLIANCE    

ciscoLwappWlanMIBComplianceRev4 2.1.9.9.512.2.1.5
The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module.
Status: deprecated Access: read-create
MODULE-COMPLIANCE    

ciscoLwappWlanMIBComplianceRev5 2.1.9.9.512.2.1.6
The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module.
Status: deprecated Access: read-create
MODULE-COMPLIANCE    

ciscoLwappWlanMIBComplianceRev6 2.1.9.9.512.2.1.7
The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module.
Status: deprecated Access: read-create
MODULE-COMPLIANCE    

ciscoLwappWlanMIBComplianceRev7 2.1.9.9.512.2.1.8
The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module.
Status: deprecated Access: read-create
MODULE-COMPLIANCE    

ciscoLwappWlanMIBComplianceRev8 2.1.9.9.512.2.1.9
The compliance statement for the SNMP entities that implement the ciscoLwappWlanMIB module.
Status: current Access: read-create
MODULE-COMPLIANCE    

ciscoLwappWlanConfigGroup 2.1.9.9.512.2.2.1
This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP. ciscoLwappWlanConfigGroup object is superseded by ciscoLwappWlanConfigGroupSup1.
Status: deprecated Access: read-create
OBJECT-GROUP    

ciscoLwappWlanConfigGroupSup1 2.1.9.9.512.2.2.2
This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanConfigClientGroup 2.1.9.9.512.2.2.3
This collection of objects represent the configuration of WLANs on the controller to be passed to an 8021.11 clients.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlan11uConfigGroup 2.1.9.9.512.2.2.4
This collection of objects represents 802.11u related configuration of WLANs on the controller to be passed to an AP. ciscoLwappWlan11uConfigGroup object is superseded by ciscoLwappWlan11uConfigGroupsup1.
Status: deprecated Access: read-create
OBJECT-GROUP    

ciscoLwappAPGroupsVlanConfigGroup 2.1.9.9.512.2.2.5
This collection of objects represent the configuration of AP Groups Vlan on the controller to be passed to an AP. ciscoLwappAPGroupsVlanConfigGroup object is superseded by ciscoLwappAPGroupsVlanConfigGroupSup2.
Status: deprecated Access: read-create
OBJECT-GROUP    

ciscoLwappWlanConfigGroupSup2 2.1.9.9.512.2.2.6
This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanConfigClientGroupSup1 2.1.9.9.512.2.2.7
This collection of objects represent the configuration of WLANs on the controller to be passed to an 8021.11 clients.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanConfigGroupSup3 2.1.9.9.512.2.2.8
This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlan11uConfigGroupsup1 2.1.9.9.512.2.2.9
This collection of objects represents 802.11u related configuration of WLANs on the controller to be passed to an AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanServiceAdvertisementConfigGroup 2.1.9.9.512.2.2.10
This collection of objects represents 802.11u related configuration of WLANs on the controller to be passed to an AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanHotSpot2ConfigGroup 2.1.9.9.512.2.2.11
This collection of objects represents 802.11u related configuration of WLANs on the controller to be passed to an AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanIosConfigGroup 2.1.9.9.512.2.2.12
This collection of objects represents IOS related configuration of WLANs on the controller to be passed to an AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanQosConfigGroup 2.1.9.9.512.2.2.13
This collection of objects represents QoS related configuration of WLANs on the controller to be passed to an AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanConfigGroupSup4 2.1.9.9.512.2.2.14
This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP.This object is superceded by ciscoLwappWlanConfigGroupSup5. ciscoLwappWlanConfigGroupSup4 object is superseded by ciscoLwappWlanConfigGroupSup5.
Status: deprecated Access: read-create
OBJECT-GROUP    

ciscoLwappWlan11uConfigGroupsup2 2.1.9.9.512.2.2.15
This collection of objects represents 802.11u related configuration of WLANs on the controller to be passed to an AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanHotSpot2ConfigGroupSup1 2.1.9.9.512.2.2.16
This collection of objects represents 802.11u related configuration of WLANs on the controller to be passed to an AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappAPGroupsVlanConfigGroupSup1 2.1.9.9.512.2.2.17
This collection of objects represent the configuration of AP Groups Vlan on the controller to be passed to an AP.
Status: current Access: read-create
OBJECT-GROUP    

cLAPGroupsVenueConfigGroup 2.1.9.9.512.2.2.18
This collection of objects represent the configuration of Venue groups on the controller to be passed to an AP.
Status: current Access: read-create
OBJECT-GROUP    

cLAPGroupsMultipleVenueGroup 2.1.9.9.512.2.2.19
This collection of objects represent the configuration of Venue groups on the controller to be passed to an AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanConfigClientGroupSup2 2.1.9.9.512.2.2.20
This collection of objects represent the configuration of WLANs on the controller to be passed to an 8021.11 clients.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanConfigFlexibleNetflowGroup 2.1.9.9.512.2.2.21
This collection of objects represent the configuration of flexible netflow policy details per WLAN on the conroller to be passed to an AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanConfigGroupSup5 2.1.9.9.512.2.2.22
This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappAPGroupsVlanConfigGroupSup2 2.1.9.9.512.2.2.23
This collection of objects represent the configuration of AP Groups Vlan on the controller to be passed to an AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanConfigGroupSup6 2.1.9.9.512.2.2.24
This collection of objects represent the configuration of WLANs on the controller to be passed to an LWAPP AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanConfigGroupSup7 2.1.9.9.512.2.2.25
This collection of objects represent the configuration of AP Groups HyperLocation on the controller to be passed to an LWAPP AP.
Status: current Access: read-create
OBJECT-GROUP    

ciscoLwappWlanConfigGroupSup8 2.1.9.9.512.2.2.26
This collection of objects represent the configuration of AP Groups LAN Port on the controller to be passed to an LWAPP AP.
Status: current Access: read-create
OBJECT-GROUP