CISCO-LWAPP-SYS-MIB

File: CISCO-LWAPP-SYS-MIB.mib (79316 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
SNMP-FRAMEWORK-MIB INET-ADDRESS-MIB CISCO-LWAPP-DOT11-CLIENT-MIB
CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
Counter32 NOTIFICATION-TYPE MODULE-COMPLIANCE
OBJECT-GROUP NOTIFICATION-GROUP RowStatus
DisplayString TruthValue SnmpAdminString
InetAddressType InetAddress InetPortNumber
cldcClientAccessVLAN cldcClientMacAddress ciscoMgmt

Defined Types

ClsTransferConfigEntry  
SEQUENCE    
  clsTransferType INTEGER
  clsTransferMode INTEGER
  clsTransferServerAddressType InetAddressType
  clsTransferServerAddress InetAddress
  clsTransferPath SnmpAdminString
  clsTransferFilename SnmpAdminString
  clsTransferFtpUsername SnmpAdminString
  clsTransferFtpPassword SnmpAdminString
  clsTransferFtpPortNum InetPortNumber
  clsTransferTftpMaxRetries Unsigned32
  clsTransferTftpTimeout Unsigned32
  clsTransferStart INTEGER
  clsTransferStatus INTEGER
  clsTransferStatusString SnmpAdminString

CLSysLogConfigEntry  
SEQUENCE    
  cLSysLogServerIndex Unsigned32
  cLSysLogAddressType InetAddressType
  cLSysLogAddress InetAddress
  cLSysLogHostRowStatus RowStatus

ClsPortModeConfigEntry  
SEQUENCE    
  clsPortDot1dBasePort Unsigned32
  clsPortModePhysicalMode INTEGER
  clsPortModePhysicalStatus INTEGER
  clsPortModeSfpType SnmpAdminString
  clsPortUpDownCount Counter32

Defined Values

ciscoLwappSysMIB 1.3.6.1.4.1.9.9.618
This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. This MIB provides global configuration and status information for the controller. All general system related information is presented in this MIB. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ + + + + + + + CC + + CC + + CC + + + + + + + +......+ +......+ +......+ .. . . .. . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + AP + + AP + + AP + + AP + + + + + + + + + +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + MN + + MN + + MN + + MN + + + + + + + + + +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably. Extensible Authentication Protocol ( EAP ) EAP is a universal authentication protocol used in wireless and PPP networks. It is defined by RFC 3748. EAP-Flexible Authentication ( EAP-FAST ) This protocol is used via secure tunneling for 802.1X EAP. PAC PAC (Protected Access Credential) is a meachanism for mutual authentication in EAP-FAST. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol. [3] IEEE 802.1X - Authentication for Wireless and Wired Connections.
MODULE-IDENTITY    

ciscoLwappSysMIBNotifs 1.3.6.1.4.1.9.9.618.0
OBJECT IDENTIFIER    

ciscoLwappSysMIBObjects 1.3.6.1.4.1.9.9.618.1
OBJECT IDENTIFIER    

ciscoLwappSysMIBConform 1.3.6.1.4.1.9.9.618.2
OBJECT IDENTIFIER    

clsConfig 1.3.6.1.4.1.9.9.618.1.1
OBJECT IDENTIFIER    

clsStatus 1.3.6.1.4.1.9.9.618.1.2
OBJECT IDENTIFIER    

clsImageInfo 1.3.6.1.4.1.9.9.618.1.3
OBJECT IDENTIFIER    

clsCpuInfo 1.3.6.1.4.1.9.9.618.1.4
OBJECT IDENTIFIER    

clsSecurityGroup 1.3.6.1.4.1.9.9.618.1.5
OBJECT IDENTIFIER    

ciscoLwappSysMIBNotifObjects 1.3.6.1.4.1.9.9.618.1.6
OBJECT IDENTIFIER    

ciscoLwappSysMIBNotifControlObjects 1.3.6.1.4.1.9.9.618.1.7
OBJECT IDENTIFIER    

clsSysInfo 1.3.6.1.4.1.9.9.618.1.8
OBJECT IDENTIFIER    

clsDot3BridgeEnabled 1.3.6.1.4.1.9.9.618.1.1.1
This object specifies whether 803.2 bridging mode is enabled or disabled on the controller. A value of 'true' specifies that the bridging mode is enabled. A value of 'false' specifies that the bridging mode is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clsConfigDownload 1.3.6.1.4.1.9.9.618.1.1.2
OBJECT IDENTIFIER    

clsConfigUpload 1.3.6.1.4.1.9.9.618.1.1.3
OBJECT IDENTIFIER    

clsDownloadFileType 1.3.6.1.4.1.9.9.618.1.1.2.1
This object specifies the file types that can be downloaded to the controller. The file types for download are: unknown - Unknown file type code - Code file config - Configuration file webAuthCert - Web authentication certificates webAdminCert - Web administrative certificates signatures - Signature file customWebAuth - Custom web authentication tar file vendorDeviceCert - Vendor device certificates vendorCaCert - Vendor certificate authority certificates
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), code(2), config(3), webAuthCert(4), webAdminCert(5), signatures(6), customWebAuth(7), vendorDeviceCert(8), vendorCaCert(9)  

clsDownloadCertificateKey 1.3.6.1.4.1.9.9.618.1.1.2.2
This object specifies the key used to encrypt the EAP certificate, specified by IEEE 802.1X standard, during upload from the controller and for decrypting the file after its downloaded to the controller. This object is relevant only when clsDownloadFileType is 'vendorDeviceCert'. For all other values of clsDownloadFileType object this will return an empty string.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

clsUploadFileType 1.3.6.1.4.1.9.9.618.1.1.3.1
This object specifies the file types that can be uploaded to the controller. The file types for upload are: unknown - Unknown file config - Configuration file errorLog - Error log systemTrace - System trace trapLog - Trap log crashFile - Crash file signatures - Signature file pac - PAC file radioCoreDump - AP's Radio core dump file invalidConfig - Upload the file which contains the invalid configuration commands feeded by the downloaded Config file. debugfile - Debug file. pktCapture - Packet Capture File watchdogCrash - Watchdog Crash Information File panicCrash - Panic Crash Information File. vendorDevCert - EAP ca certificate. vendorCaCert - EAP dev certificate. webAdminCert - Web Admin certificate. webAuthCert - Web Auth certificate.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), config(2), errorLog(3), systemTrace(4), trapLog(5), crashFile(6), signatures(7), pac(8), radioCoreDump(9), invalidConfig(10), debugfile(11), pktCapture(12), watchdogCrash(13), panicCrash(14), vendorDevCert(15), vendorCaCert(16), webAdminCert(17), webAuthCert(18)  

clsUploadPacUsername 1.3.6.1.4.1.9.9.618.1.1.3.2
This object specifies the upload user name for protected access credential (PAC). This object needs to be set before setting clsUploadFileType to 'pac'. For all other values of clsUploadFileType this will return an empty string.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..63)  

clsUploadPacPassword 1.3.6.1.4.1.9.9.618.1.1.3.3
This object specifies the upload password for protected access credential (PAC). This object needs to be set before setting clsUploadFileType to 'pac'. For all other values of clsUploadFileType this will return an empty string.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..128)  

clsUploadPacValidity 1.3.6.1.4.1.9.9.618.1.1.3.4
This object specifies the upload validity in days for protected access credential (PAC). This object is relevant only when clsUploadFileType is set to 'pac'. For all other values of clsUploadFileType this will return an empty string.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

clsTransferConfigGroup 1.3.6.1.4.1.9.9.618.1.1.4
OBJECT IDENTIFIER    

clsTransferConfigFileEncryption 1.3.6.1.4.1.9.9.618.1.1.4.1
The configuration file can be encrypted before upload from the controller and then decrypted before downloading to the controller when this option is enabled. This is applicable only when clsDownloadFileType, clsUploadFileType is set to Config.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

clsTransferConfigFileEncryptionKey 1.3.6.1.4.1.9.9.618.1.1.4.2
This is the key to be used when encrypting the configuration file while upload from the controller or while decrypting the file after download to the controller. This is applicable only when clsDownloadFileType, clsUploadFileType is set to Config.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..16)  

clsTransferConfig 1.3.6.1.4.1.9.9.618.1.1.8
OBJECT IDENTIFIER    

clsTransferConfigTable 1.3.6.1.4.1.9.9.618.1.1.8.1
This table is used to configure the server details which will be used by the controller to upload/download files.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClsTransferConfigEntry

clsTransferConfigEntry 1.3.6.1.4.1.9.9.618.1.1.8.1.1
Each entry in this table provides information about the server to which the controller will upload/download files.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClsTransferConfigEntry  

clsTransferType 1.3.6.1.4.1.9.9.618.1.1.8.1.1.1
Transfer type configures the type of operation with the server by the controller. The mode is either Upload or Download.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER download(1), upload(2)  

clsTransferMode 1.3.6.1.4.1.9.9.618.1.1.8.1.1.2
Transfer mode configures the mode of transfer used by the controller with the server. The mode is either TFTP or FTP/SFTP.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER tftp(1), ftp(2), sftp(3)  

clsTransferServerAddressType 1.3.6.1.4.1.9.9.618.1.1.8.1.1.3
This object represents the address type of the Server to which the controller will transfer the file.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

clsTransferServerAddress 1.3.6.1.4.1.9.9.618.1.1.8.1.1.4
This object represents the address of the Server to which the controller will transfer the file.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

clsTransferPath 1.3.6.1.4.1.9.9.618.1.1.8.1.1.5
Transfer path configures the directory path for file transfer. The controller remembers the last file path used.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

clsTransferFilename 1.3.6.1.4.1.9.9.618.1.1.8.1.1.6
Transfer filename configures the file name for the file being transferred from the controller. The controller remembers the last file name used. An example would be File Path set to c: ftp\code\ and File Name set to e1r1v1.opr.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

clsTransferFtpUsername 1.3.6.1.4.1.9.9.618.1.1.8.1.1.7
This object is used to store the FTP username for transferring file on the server. This is valid only for FTP transfer mode.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..31)  

clsTransferFtpPassword 1.3.6.1.4.1.9.9.618.1.1.8.1.1.8
This object is used to store the FTP password for transferring file on the server. This is valid only for FTP transfer mode.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..31)  

clsTransferFtpPortNum 1.3.6.1.4.1.9.9.618.1.1.8.1.1.9
This object is used to store the port number to be used by the FTP protocol while connecting to the server. This is valid only for FTP transfer mode.
Status: current Access: read-write
OBJECT-TYPE    
  InetPortNumber  

clsTransferTftpMaxRetries 1.3.6.1.4.1.9.9.618.1.1.8.1.1.10
Maximum number of retries to be allowed for a TFTP message packet. This is valid only for TFTP transfer mode.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..254  

clsTransferTftpTimeout 1.3.6.1.4.1.9.9.618.1.1.8.1.1.11
Timeout in seconds for a TFTP message packet. This is valid only for TFTP transfer mode.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..254  

clsTransferStart 1.3.6.1.4.1.9.9.618.1.1.8.1.1.12
Transfer start will start the file transfer operation on Active when it is set to initiate(2), it will return none(1) for GET. Transfer start will start the file transfer operation on Standby when it is set to initiatePeer(3),
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), initiate(2), initiatePeer(3)  

clsTransferStatus 1.3.6.1.4.1.9.9.618.1.1.8.1.1.13
Indicates the current status of a transfer. Following are valid only when clsTransferType is 'download' :- bootBreakOff(14), invalidTarFile(15).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notInitiated(1), transferStarting(2), errorStarting(3), wrongFileType(4), updatingConfig(5), invalidConfigFile(6), writingToFlash(7), failureWritingToFlash(8), checkingCRC(9), failedCRC(10), unknownDirection(11), transferSuccessful(12), transferFailed(13), bootBreakOff(14), invalidTarFile(15), unknown(99)  

clsTransferStatusString 1.3.6.1.4.1.9.9.618.1.1.8.1.1.14
Indicates in string format about the current status of a transfer.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

clsConfigGeneral 1.3.6.1.4.1.9.9.618.1.1.5
OBJECT IDENTIFIER    

clsTimeZone 1.3.6.1.4.1.9.9.618.1.1.5.1
This object timezone for the controller. Enter the timezone location index. 1. (GMT-12:00) International Date Line West 2. (GMT-11:00) Samoa 3. (GMT-10:00) Hawaii 4. (GMT -9:00) Alaska 5. (GMT -8:00) Pacific Time (US and Canada) 6. (GMT -7:00) Mountain Time (US and Canada) 7. (GMT -6:00) Central Time (US and Canada) 8. (GMT -5:00) Eastern Time (US and Canada) 9. (GMT -4:00) Altantic Time (Canada) 10. (GMT -3:00) Buenos Aires (Agentina) 11. (GMT -2:00) Mid-Atlantic 12. (GMT -1:00) Azores 13. (GMT) London, Lisbon, Dublin, Edinburgh 14. (GMT +1:00) Amsterdam, Berlin, Rome, Vienna 15. (GMT +2:00) Jerusalem 16. (GMT +3:00) Baghdad 17. (GMT +4:00) Muscat, Abu Dhabi 18. (GMT +4:30) Kabul 19. (GMT +5:00) Karachi, Islamabad, Tashkent 20. (GMT +5:30) Colombo, Kolkata, Mumbai, New Delhi 21. (GMT +5:45) Katmandu 22. (GMT +6:00) Almaty, Novosibirsk 23. (GMT +6:30) Rangoon 24. (GMT +7:00) Saigon, Hanoi, Bangkok, Jakatar 25. (GMT +8:00) HongKong, Bejing, Chongquing 26. (GMT +9:00) Tokyo, Osaka, Sapporo 27. (GMT +9:30) Darwin 28. (GMT+10:00) Sydney, Melbourne, Canberra 29. (GMT+11:00) Magadan, Solomon Is., New Caledonia 30. (GMT+12:00) Kamchatka, Marshall Is., Fiji
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

clsTimeZoneDescription 1.3.6.1.4.1.9.9.618.1.1.5.2
This object represents the timezone description for the controller.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

clsMaxClientsTrapThreshold 1.3.6.1.4.1.9.9.618.1.1.5.3
This object specifies the threshold number of clients on the controller to trigger a trap. The trap ciscoLwappMaxClientsReached will be triggered once the count of clients on the controller reaches this limit and the clsMaxClientsTrapEnabled is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

clsMaxRFIDTagsTrapThreshold 1.3.6.1.4.1.9.9.618.1.1.5.4
This object specifies the threshold number of RFID tags on the controller to trigger a trap. The trap ciscoLwappMaxRFIDTagsReached will be triggered once the count of RFID tags on the controller reaches this limit and the clsMaxRFIDTagsTrapEnabled is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

clsSyslogIpConfig 1.3.6.1.4.1.9.9.618.1.1.6
OBJECT IDENTIFIER    

cLSysLogConfigTable 1.3.6.1.4.1.9.9.618.1.1.6.1
This table is used to configure multiple syslog servers to which the the syslog messages will be sent to by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLSysLogConfigEntry

cLSysLogConfigEntry 1.3.6.1.4.1.9.9.618.1.1.6.1.1
Each entry in this table provides information about the host to which the syslog messages will be sent to.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLSysLogConfigEntry  

cLSysLogServerIndex 1.3.6.1.4.1.9.9.618.1.1.6.1.1.1
This object represents the index of the host to which syslog messages will be sent.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

cLSysLogAddressType 1.3.6.1.4.1.9.9.618.1.1.6.1.1.2
This object represents the address type of the host to which syslog messages will be sent. 'dns' is used when the hostname of the server is configured.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

cLSysLogAddress 1.3.6.1.4.1.9.9.618.1.1.6.1.1.3
This object represents the ipaddress or hostname of the host to which syslog messages will be sent.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

cLSysLogHostRowStatus 1.3.6.1.4.1.9.9.618.1.1.6.1.1.4
This is the status column for this row and is used to create and delete specific instances of rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLSysArpUnicastEnabled 1.3.6.1.4.1.9.9.618.1.1.7
This object specifies whether ARP unicast is enabled or disabled on the controller. A value of 'true' specifies that the ARP unicast is enabled. A value of 'false' specifies that the ARP unicast is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLSysBroadcastForwardingEnabled 1.3.6.1.4.1.9.9.618.1.1.9
This object specifies whether broadcast forwarding is enabled or disabled on the controller. A value of 'true' specifies that the broadcast forwarding is enabled. A value of 'false' specifies that the broadcast forwarding is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLSysLagModeEnabled 1.3.6.1.4.1.9.9.618.1.1.10
This object specifies whether Link Aggregation(LAG) mode is enabled or disabled on the controller. A value of 'true' specifies that the LAG mode is enabled. A value of 'false' specifies that the LAG mode is disabled on the controller.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clsConfigProductBranchVersion 1.3.6.1.4.1.9.9.618.1.1.11
This string contains the branch name of the specific controller branch. For Mesh branches, this string has the value M(Mesh). Zero length string is returned if there is no branch name. This string is append to the product version for display purposes. For example, if the mesh product version is 4.1.191.10, a manager application may display the version string as 4.1.191.10M (Mesh)
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

clsConfigDhcpProxyEnabled 1.3.6.1.4.1.9.9.618.1.1.12
This object represents whether the DHCP proxy option is enabled or disabled. A value of 'true' specifies that the proxy option is enabled on the controller. A value of 'false' specifies that the proxy option is disabled on the controller.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLSysMulticastIGMP 1.3.6.1.4.1.9.9.618.1.1.13
OBJECT IDENTIFIER    

cLSysMulticastIGMPSnoopingEnabled 1.3.6.1.4.1.9.9.618.1.1.13.1
This object specifies whether Multicast IGMP Snooping is enabled or disabled on the controller. A value of 'true' specifies that the Multicast IGMP Snooping is enabled. To enable this, agentNetworkMulticastMode/clsConfigMulticastEnabled must not be in disabled state. A value of 'false' specifies that the Multicast IGMP Snooping is disabled on the controller.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLSysMulticastIGMPSnoopingTimeout 1.3.6.1.4.1.9.9.618.1.1.13.2
This object specifies the IGMP timeout, in seconds. To set this value, cLSysMulticastIGMPSnoopingEnabled must be set to True. When the timeout expires, the controller sends a query on all WLANs, causing all clients that are listening to a multicast group to send a packet back to the controller.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLSysMulticastIGMPQueryInterval 1.3.6.1.4.1.9.9.618.1.1.13.3
This object specifies the IGMP query interval, in seconds. To set this value, cLSysMulticastIGMPSnoopingEnabled must be set to True.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLSPortModeConfig 1.3.6.1.4.1.9.9.618.1.1.14
OBJECT IDENTIFIER    

clsPortModeConfigTable 1.3.6.1.4.1.9.9.618.1.1.14.1
This table contains the entries for physical port related parameters
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClsPortModeConfigEntry

clsPortModeConfigEntry 1.3.6.1.4.1.9.9.618.1.1.14.1.1
This entry contains the Switch's physical port phyical mode related attribues
Status: current Access: not-accessible
OBJECT-TYPE    
  ClsPortModeConfigEntry  

clsPortDot1dBasePort 1.3.6.1.4.1.9.9.618.1.1.14.1.1.1
This object is a unique unsigned integer value which identifies the base port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..65535  

clsPortModePhysicalMode 1.3.6.1.4.1.9.9.618.1.1.14.1.1.2
The switch's Port Speed Mode. This is the configured physical mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER autoNegotiate(1), half10(2), full10(3), half100(4), full100(5), full1000sx(6), half1000(7), full1000(8), half10000(9), full10000(10)  

clsPortModePhysicalStatus 1.3.6.1.4.1.9.9.618.1.1.14.1.1.3
The switch's Port Physical Speed Status.This is the current actual speed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), autonegotiate(2), half10(3), full10(4), half100(5), full100(6), full1000sx(7), half1000(8), full1000(9), half10000(10), full10000(11)  

clsPortModeSfpType 1.3.6.1.4.1.9.9.618.1.1.14.1.1.4
This object represents the SFP's type of the port.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

clsPortUpDownCount 1.3.6.1.4.1.9.9.618.1.1.14.1.1.5
This object represents the total number of up/down count of the port. Every time the value of ifOperStatus is changed, this MIB should be incremented.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

clsCoreDump 1.3.6.1.4.1.9.9.618.1.1.15
OBJECT IDENTIFIER    

clsCoreDumpTransferEnable 1.3.6.1.4.1.9.9.618.1.1.15.1
This object specifies whether the core dump file transfer is enabled or disabled. If the value is True the core-dump feature is Enabled otherwise Disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clsCoreDumpTransferMode 1.3.6.1.4.1.9.9.618.1.1.15.2
This Object specifies the Core Dump Transfer Mode. If the value is FTP then only FTP attributes clsCoreDumpServerIPAddress, clsCoreDumpFileName, clsCoreDumpUserName, clsCoreDumpPassword can be set, unknown value is not SETable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), ftp(2)  

clsCoreDumpServerIPAddressType 1.3.6.1.4.1.9.9.618.1.1.15.3
This Object Id Specifies the IP Address Type of Server.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

clsCoreDumpServerIPAddress 1.3.6.1.4.1.9.9.618.1.1.15.4
This object specifies the IP Address of the Server where the core-dump will be uploaded.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

clsCoreDumpFileName 1.3.6.1.4.1.9.9.618.1.1.15.5
This object specifies the File Name of the core-dump by which you want to save it on the Server.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

clsCoreDumpUserName 1.3.6.1.4.1.9.9.618.1.1.15.6
This object specifies the Login Name at the FTP server.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

clsCoreDumpPassword 1.3.6.1.4.1.9.9.618.1.1.15.7
This object specifies the Login Password of the FTP server.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

clsConfigMulticastEnabled 1.3.6.1.4.1.9.9.618.1.1.16
This object represents whether global multicast is enabled or disabled. A value of 'true' specifies that the multicast option is enabled on the controller. A value of 'false' specifies that the multicast option is disabled on the controller.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLSysMulticastMLD 1.3.6.1.4.1.9.9.618.1.1.17
OBJECT IDENTIFIER    

cLSysMulticastMLDSnoopingEnabled 1.3.6.1.4.1.9.9.618.1.1.17.1
This object specifies whether Multicast MLD Snooping is enabled or disabled on the controller. A value of 'true' specifies that the Multicast MLD Snooping is enabled. To enable this, agentNetworkMulticastMode/ clsConfigMulticastEnabled must not be in disabled state. A value of 'false' specifies that the Multicast MLD Snooping is disabled on the controller.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLSysMulticastMLDSnoopingTimeout 1.3.6.1.4.1.9.9.618.1.1.17.2
This object specifies the MLD timeout, in seconds. To set this value, cLSysMulticastMLDSnoopingEnabled must be set to True. When the timeout expires, the controller sends a query on all WLANs, causing all clients that are listening to a multicast group to send a packet back to the controller.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLSysMulticastMLDQueryInterval 1.3.6.1.4.1.9.9.618.1.1.17.3
This object specifies the MLD query interval, in seconds. To set this value, cLSysMulticastMLDSnoopingEnabled must be set to True.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

clsConfigStats 1.3.6.1.4.1.9.9.618.1.1.18
OBJECT IDENTIFIER    

clsSysRealtimeStatsTimer 1.3.6.1.4.1.9.9.618.1.1.18.1
This object specifies the realtime stats interval of the system. There are 2 stats modes: realtime and normal. realtime interval is much less than normal mode.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 2..5  

clsSysNormalStatsTimer 1.3.6.1.4.1.9.9.618.1.1.18.2
This object specifies the normal stats interval of the system. There are 2 stats modes: realtime and normal. realtime interval is much less than normal mode.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 10..180  

clsSysStatsSamplingInterval 1.3.6.1.4.1.9.9.618.1.1.18.3
This object specifies the sampling interval of the system, which is applied to WLC and APs connected to this WLC. WLC and APs poll specific data every sampling interval.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

clsSysStatsAverageInterval 1.3.6.1.4.1.9.9.618.1.1.18.4
This object specifies the average statistics interval of the system, which is applied to WLC and APs connected to this WLC. This interval works as a time window for calculating the average value of the data polled by WLC/AP every sampling interval.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

clsAlarmObjects 1.3.6.1.4.1.9.9.618.1.1.19
OBJECT IDENTIFIER    

clsAlarmHoldTime 1.3.6.1.4.1.9.9.618.1.1.19.1
This object specifies the time in seconds for which an alarm object should be soaked when its on/off state is changed.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..3600  

clsAlarmTrapRetransmitInterval 1.3.6.1.4.1.9.9.618.1.1.19.2
This object specifies the interval in seconds in which alarm traps, if any, are retransmitted. Setting this value to 0 means no retransmission.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

clsSysThresholdConfig 1.3.6.1.4.1.9.9.618.1.1.20
OBJECT IDENTIFIER    

clsSysControllerCpuUsageThreshold 1.3.6.1.4.1.9.9.618.1.1.20.1
This object specifies the CPU usage threshold on a controller. Setting this value to 0 means no threshold.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

clsSysControllerMemoryUsageThreshold 1.3.6.1.4.1.9.9.618.1.1.20.2
This object specifies the memory usage threshold on a controller. Setting this value to 0 means no threshold.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

clsSysApCpuUsageThreshold 1.3.6.1.4.1.9.9.618.1.1.20.3
This object specifies the CPU usage threshold on a AP. Setting this value to 0 means no threshold.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

clsSysApMemoryUsageThreshold 1.3.6.1.4.1.9.9.618.1.1.20.4
This object specifies the memory usage threshold on a AP. Setting this value to 0 means no threshold.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

clsNMHeartBeat 1.3.6.1.4.1.9.9.618.1.1.21
OBJECT IDENTIFIER    

clsNMHeartBeatEnable 1.3.6.1.4.1.9.9.618.1.1.21.1
This object specifies whether heart beat trap to network manager is enabled or disabled. If the value is True the Network Manager Heart Beat feature is Enabled otherwise Disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clsNMHeartBeatInterval 1.3.6.1.4.1.9.9.618.1.1.21.2
This object specifies the interval in seconds in heart beat traps to network manager.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..65535  

clsCrashSystem 1.3.6.1.4.1.9.9.618.1.1.99
This object resets the switch with a crash. If a value of of 'true' is set, the swicth would crash. GET on this object would return 'false'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLSysLagModeInTransition 1.3.6.1.4.1.9.9.618.1.2.1
This object specifies whether the LAG mode is in transition on the controller. A value of 'true' specifies that the LAG mode is in transition and the controller has to be rebooted to take effect.A value of 'false' specifies that the LAG mode is not in transition.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

clsEmergencyImageVersion 1.3.6.1.4.1.9.9.618.1.3.1
Cisco recommends installing Cisco Unified Wireless Network Controller Boot Software , (*_ER.aes , where star denotes the version of the controller image ) on all controller platforms. If this ER.aes is not installed, the controller would not be able to show the Emergency Image Version correctly(or Field Recovery Image Version), and would be shown as 'N/A'. The ER.aes files are independent from the controller software files. Any controller software file can be run with any ER.aes file. However, installing the latest boot software file (*_ER.aes , where star denotes the controller version) ensures that the boot software modifications in all of the previous and current boot software ER.aes files are installed.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

clsSecStrongPwdCaseCheck 1.3.6.1.4.1.9.9.618.1.5.1
This object is used to enable/disable the case check for the passwords configured in controller. When enabled, the new password must contain characters from at least three of the following classes : lowercase letters, uppercase letters, digits and special characters.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clsSecStrongPwdConsecutiveCheck 1.3.6.1.4.1.9.9.618.1.5.2
This object is used to enable/disable the consecutive check for the passwords configured in controller. When enabled, the password provided should not have a character repeated more than thrice consecutively.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clsSecStrongPwdDefaultCheck 1.3.6.1.4.1.9.9.618.1.5.3
This object is used to enable/disable the default check for the passwords configured in controller. When enabled, the new password must not be 'cisco', 'ocsic', 'admin', 'nimda' or any variant obtained by changing the capitalization of letters therein, or by substituting '1' '|' or '!' for i, and/or substituting '0' for 'o', and/or substituting '$' for 's'
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clsSecStrongPwdAsUserNameCheck 1.3.6.1.4.1.9.9.618.1.5.4
This object is used to enable/disable the username check for the password configured in controller. When enabled the new password must not be same as the associated username or the reversed username.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clsSysFlashSize 1.3.6.1.4.1.9.9.618.1.8.1
This object specifies the total flash memory size in Kbytes.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clsSysMemoryType 1.3.6.1.4.1.9.9.618.1.8.2
This object specifies the system memory type.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

clsSysMaxClients 1.3.6.1.4.1.9.9.618.1.8.3
This object specifies max associated clients supported per WLC
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clsSysApConnectCount 1.3.6.1.4.1.9.9.618.1.8.4
This object specifies the count of AP's that are connected with WLC
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clsSysNetId 1.3.6.1.4.1.9.9.618.1.8.5
This object specifies the SysNetId which is the numeric string to identify the system information like SysName
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

clsSysCurrentMemoryUsage 1.3.6.1.4.1.9.9.618.1.8.6
This object specifies the current percent usage of system memory. This MIB should be updated every clsSysStatsSamplingInterval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clsSysAverageMemoryUsage 1.3.6.1.4.1.9.9.618.1.8.7
This object specifies the average percent usage of system memory. The memory average usage should be the average of memory-Usage during the time window specified by clsSysStatsAverageInterval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clsSysCurrentCpuUsage 1.3.6.1.4.1.9.9.618.1.8.8
This object specifies the current percent usage of all CPUs. This MIB should be updated every clsSysStatsSamplingInterval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clsSysAverageCpuUsage 1.3.6.1.4.1.9.9.618.1.8.9
This object specifies the average percent CPU usage. The average CPU usage should be the average of CPU-Usage during the time window specified by clsSysStatsAverageInterval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clsSysCpuType 1.3.6.1.4.1.9.9.618.1.8.10
This object specifies the cpu type.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

clsMaxRFIDTagsCount 1.3.6.1.4.1.9.9.618.1.8.11
This object represents the maximum RFID tags present on the controller.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clsMaxClientsCount 1.3.6.1.4.1.9.9.618.1.8.12
This object represents the maximum clients present on the controller.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clsSecStrongPwdCheckTrapEnabled 1.3.6.1.4.1.9.9.618.1.7.1
This object specifies whether the ciscoLwappStrongPwdCheck notification would be generated. A value of 'true' indicates that the agent generates ciscoLwappStrongPwdCheck notification. A value of 'false' indicates that the agent doesn't generate ciscoLwappStrongPwdCheck notification.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clsMaxClientsTrapEnabled 1.3.6.1.4.1.9.9.618.1.7.2
This object specifies whether the ciscoLwappMaxClientsReached notification would be generated. A value of 'true' indicates that the agent generates ciscoLwappMaxClientsReached notification. A value of 'false' indicates that the agent doesn't generate ciscoLwappMaxClientsReached notification.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clsMaxRFIDTagsTrapEnabled 1.3.6.1.4.1.9.9.618.1.7.3
This object specifies whether the ciscoLwappMaxRFIDTagsReached notification would be generated. A value of 'true' indicates that the agent generates ciscoLwappMaxRFIDTagsReached notification. A value of 'false' indicates that the agent doesn't generate ciscoLwappMaxRFIDTagsReached notification.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clsSecStrongPwdManagementUser 1.3.6.1.4.1.9.9.618.1.6.1
This object specifies the management user who enabled/disabled the strong password checks.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING Size(1..24)  

clsSecStrongPwdCheckType 1.3.6.1.4.1.9.9.618.1.6.2
This object specifies the type of the check that was enabled/disabled by the management user.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER caseCheck(1), consecutiveCheck(2), defaultCheck(3), usernameCheck(4), allChecks(5)  

clsSecStrongPwdCheckOption 1.3.6.1.4.1.9.9.618.1.6.3
This object specifies whether the strong password check was enabled/disabled.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  TruthValue  

clsSysAlarmSet 1.3.6.1.4.1.9.9.618.1.6.4
This object specifies whether this system alarm is raise or clear. A value of 'true' indicates this event is set. A value of 'false' indicates this even is cleared.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  TruthValue  

ciscoLwappSysInvalidXmlConfig 1.3.6.1.4.1.9.9.618.0.1
This notification will be sent whenever invalid configuration detected by XML
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappNoVlanConfigured 1.3.6.1.4.1.9.9.618.0.2
This notification will be sent whenever wired client tries to associate without interface for specified vlan
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappStrongPwdCheck 1.3.6.1.4.1.9.9.618.0.3
This notification will be sent whenever the management user enables/disables the strong password rules.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappSysCpuUsageHigh 1.3.6.1.4.1.9.9.618.0.4
When a WLC detects its CPU usage is higher than the threshold configured in clsSysControllerCpuUsageThreshold, this notification is generated with clsSysAlarmSet set to true. When its CPU usage falls below the threshold lately, this notification is generated with clsSysAlarmSet set to false.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappSysMemoryUsageHigh 1.3.6.1.4.1.9.9.618.0.5
When a WLC detects its memory usage is higher than the threshold configured in clsSysControllerMemoryUsageThreshold, this notification is generated with clsSysAlarmSet set to true. When its memory usage falls below the threshold lately, this notification is generated with clsSysAlarmSet set to false.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMaxRFIDTagsReached 1.3.6.1.4.1.9.9.618.0.6
This notification is generated when the number of RFID tags on the controller exceeds the limit defined by clsMaxRFIDTagsTrapThreshold.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMaxClientsReached 1.3.6.1.4.1.9.9.618.0.7
This notification is generated when the number of clients on the controller exceeds the limit defined by clsMaxClientsTrapThreshold.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappNMHeartBeat 1.3.6.1.4.1.9.9.618.0.8
This notification will be sent when Network Mamager Heart Beat Enable.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

clsAllCpuUsage 1.3.6.1.4.1.9.9.618.1.4.1
This object specifies the CPU usage string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

ciscoLwappSysMIBCompliances 1.3.6.1.4.1.9.9.618.2.1
OBJECT IDENTIFIER    

ciscoLwappSysMIBGroups 1.3.6.1.4.1.9.9.618.2.2
OBJECT IDENTIFIER    

ciscoLwappSysMIBCompliance 1.3.6.1.4.1.9.9.618.2.1.1
The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoLwappSysMIBComplianceRev1 1.3.6.1.4.1.9.9.618.2.1.2
The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoLwappSysMIBComplianceRev2 1.3.6.1.4.1.9.9.618.2.1.3
The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module. This deprecates ciscoLwappSysMIBComplianceRev1.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoLwappSysMIBComplianceRev3 1.3.6.1.4.1.9.9.618.2.1.4
The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module. This deprecates ciscoLwappSysMIBComplianceRev2.
Status: current Access: read-only
MODULE-COMPLIANCE    

ciscoLwappSysConfigGroup 1.3.6.1.4.1.9.9.618.2.2.1
This collection of objects represent the system wide configuration on the controller.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysConfigFileEncryptionGroup 1.3.6.1.4.1.9.9.618.2.2.2
This object represents the System encryption configuration on the controller.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysTransferOperationConfigGroup 1.3.6.1.4.1.9.9.618.2.2.3
This object represents the System Transfer operation configuration on the controller.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysPortConfigGroup 1.3.6.1.4.1.9.9.618.2.2.4
This collection of objects represent the system wide configuration on the controller.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysSecurityConfigGroup 1.3.6.1.4.1.9.9.618.2.2.5
This collection of objects represent the system security configuration on the controller.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysIgmpConfigGroup 1.3.6.1.4.1.9.9.618.2.2.6
This collection of objects represent the IGMP multicast configuration on the controller.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysSecNotifObjsGroup 1.3.6.1.4.1.9.9.618.2.2.7
This collection of objects represent the information carried by the security related notifications sent by the agent to a network management station.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysNotifsGroup 1.3.6.1.4.1.9.9.618.2.2.8
This collection of objects represent the system config related notifications sent by the agent to a network management station.
Status: current Access: read-only
NOTIFICATION-GROUP    

ciscoLwappSysNotifControlGroup 1.3.6.1.4.1.9.9.618.2.2.9
This collection of objects represent the flags to control the generation of notification.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysConfigGroupVer1 1.3.6.1.4.1.9.9.618.2.2.10
This collection of objects represent the system wide configuration on the controller.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysConfigGroupSup1 1.3.6.1.4.1.9.9.618.2.2.11
This collection of objects represents the timzone and syslog configuration on the controller.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysMldConfigGroup 1.3.6.1.4.1.9.9.618.2.2.12
This collection of objects represent the MLD multicast configuration on the controller.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysConfigStatsGroup 1.3.6.1.4.1.9.9.618.2.2.13
This collection of objects represents the statistics intervals configuration on the controller.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysAlarmObjectGroup 1.3.6.1.4.1.9.9.618.2.2.14
This collection of objects represents the alarm objetcs configurations on the controller.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysThresholdGroup 1.3.6.1.4.1.9.9.618.2.2.15
This collection of objects represents the Threshold configuration on the controller.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysHeartBeatGroup 1.3.6.1.4.1.9.9.618.2.2.16
This collection of objects represents the heart beat configurations on the controller.
Status: current Access: read-only
OBJECT-GROUP    

ciscoLwappSysInfoGroup 1.3.6.1.4.1.9.9.618.2.2.17
This group of object represents the system information of the controller.
Status: current Access: read-only
OBJECT-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor