CISCO-L2-CONTROL-MIB

File: CISCO-L2-CONTROL-MIB.mib (65058 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
CISCO-SMI ENTITY-MIB Q-BRIDGE-MIB
IF-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Unsigned32 MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP TruthValue RowStatus
TEXTUAL-CONVENTION ciscoMgmt entPhysicalIndex
VlanIndex InterfaceIndex ifIndex

Defined Types

MacLimitExceededAction  
The action that will be taken by the system on an entity, when the system detects the current learned number of MAC addresses in the forwarding table has exceeded the limit number of MAC addresses which is configured by the users. The entities that will be affected by the action are VLAN, interface or interface-VLAN pair. warning : The violation will only generate the notification and no further action will be taken. limit : The notification will be generated as the 'warning' action and also the MAC limit is enforced for the entity. It means that the new address will not be learned in the entity and the traffic with new addresses will be flooded in the entity. The learning will be re-enabled in the entity if the number of MAC addresses falls below the limit. limitNoFlood : The notification will be generated as the 'warning' action and also the MAC limit is enforced for the entity but no flooding traffic for unknown unicast MAC address packets. It means that the new addresses will not be learned in the entity and also the traffic with new addresses will not be flooded in the entity. The learning will be re-enabled in the entity if the number of MAC addresses falls below the limit. shutdown : The notification will be generated as the 'warning' action and the system will move the corresponding entity to blocked state, no traffic in the entity. The traffic will be re-enabled in the entity if the number of MAC addresses falls below the limit.
TEXTUAL-CONVENTION    
  INTEGER warning(1), limit(2), limitNoFlood(3), shutdown(4)  

ClcMacAddressStatsType  
The type of MAC address statistics. 'allMac' - All MAC addresses 'dynamicMac' - dynamic MAC addresses 'staticMac' - static MAC addresses 'mcastMac' - multicast MAC addresses 'pvlanCloneMac' - PVLAN clone MAC addresses 'overlayMac' - overlay MAC addresses 'secureMac' - secure MAC addresses
TEXTUAL-CONVENTION    
  INTEGER allMac(1), dynamicMac(2), staticMac(3), mcastMac(4), pvlanCloneMac(5), overlayMac(6), secureMac(7)  

ClcVlanMacLimitEntry  
SEQUENCE    
  clcVlanMacLimitIndex Unsigned32
  clcVlanMacLimitGlobalConfig BITS
  clcVlanMaxMacLimit Unsigned32
  clcVlanMacLimitExceededAction MacLimitExceededAction
  clcVlanMacLimitStatus RowStatus
  clcVlanMacLimitEnable TruthValue
  clcVlanMacLimitHigh Unsigned32
  clcVlanMacLimitHighExceedAction MacLimitExceededAction

ClcFdbVlanInfoEntry  
SEQUENCE    
  clcFdbVlanMacUsage Unsigned32

ClcUnicastFloodEntry  
SEQUENCE    
  clcUnicastFloodAdminEnable TruthValue
  clcUnicastFloodOperEnable TruthValue

ClcIfMacLimitEntry  
SEQUENCE    
  clcIfMacLimitIfIndex InterfaceIndex
  clcIfMacLimitEnable TruthValue
  clcIfMacLimitGlobalConfig BITS
  clcIfMacLimitLow Unsigned32
  clcIfMacLimitLowExceedAction MacLimitExceededAction
  clcIfMacLimitHigh Unsigned32
  clcIfMacLimitHighExceedAction MacLimitExceededAction
  clcIfMacLimitStatus RowStatus

ClcFdbIfInfoEntry  
SEQUENCE    
  clcFdbIfMacUsage Unsigned32

ClcIfVlanMacLimitEntry  
SEQUENCE    
  clcIfVlanMacLimitIfIndex InterfaceIndex
  clcIfVlanMacLimitVlanIndex VlanIndex
  clcIfVlanMacLimitEnable TruthValue
  clcIfVlanMacLimitGlobalConfig BITS
  clcIfVlanMacLimitLow Unsigned32
  clcIfVlanMacLimitLowExceedAction MacLimitExceededAction
  clcIfVlanMacLimitHigh Unsigned32
  clcIfVlanMacLimitHiExceedAction MacLimitExceededAction
  clcIfVlanMacLimitStatus RowStatus

ClcFdbIfVlanInfoEntry  
SEQUENCE    
  clcFdbIfVlanMacUsage Unsigned32

ClcFdbMacAddressStatsEntry  
SEQUENCE    
  clcFdbMacAddressStatsType ClcMacAddressStatsType
  clcFdbMacAddressStatsNumber Unsigned32

Defined Values

ciscoL2ControlMIB 1.3.6.1.4.1.9.9.313
The CISCO-L2-CONTROL-MIB is used to control some layer 2 functions, including MAC limit function and unicast flooding. This device could be a router or a switch.
MODULE-IDENTITY    

ciscoL2ControlMIBNotifs 1.3.6.1.4.1.9.9.313.0
OBJECT IDENTIFIER    

ciscoL2ControlMIBObjects 1.3.6.1.4.1.9.9.313.1
OBJECT IDENTIFIER    

ciscoL2ControlMIBConformance 1.3.6.1.4.1.9.9.313.2
OBJECT IDENTIFIER    

clcMacAddressLimitObjects 1.3.6.1.4.1.9.9.313.1.1
OBJECT IDENTIFIER    

clcUnicastFloodObjects 1.3.6.1.4.1.9.9.313.1.2
OBJECT IDENTIFIER    

clcIfMacAddressLimitObjects 1.3.6.1.4.1.9.9.313.1.3
OBJECT IDENTIFIER    

clcIfVlanMacAddressLimitObjects 1.3.6.1.4.1.9.9.313.1.4
OBJECT IDENTIFIER    

clcMacAddressStatsObjects 1.3.6.1.4.1.9.9.313.1.5
OBJECT IDENTIFIER    

clcMacLimitEnable 1.3.6.1.4.1.9.9.313.1.1.1
This object is to enable or disable the limit of number of MAC addresses function globally. MAC limit function is to try to control the number of MAC addresses for each VLAN or interface or interface-VLAN pair in the forwarding tables for a network device. It is possible that one VLAN or one interface or interface-VLAN pair can exhaust all available MAC entries because of Denial-of-Service and cause users' traffic on the other VLANS or interfaces flooded. To prevent this situation, the MAC limit for each VLAN or interface or interface-VLAN pair is needed. The major function of this feature is to protect the layer 2 forwarding table.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clcMaxMacLimitDefault 1.3.6.1.4.1.9.9.313.1.1.2
The global default value for low threshold limit number of MAC addresses in the system.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

clcMacLimitExceededActionDefault 1.3.6.1.4.1.9.9.313.1.1.3
The global default action to be taken by the system when the number of MAC addresses in the forwarding table has exceeded the low threshold number of MAC address limit for a VLAN or an interface or for interface-VLAN pair.
Status: current Access: read-write
OBJECT-TYPE    
  MacLimitExceededAction  

clcMacLimitExceedNotifOption 1.3.6.1.4.1.9.9.313.1.1.4
This MIB object provides the choices of generating MAC limit exceeded notification to the users. When the system detects the current learned number of MAC addresses in the forwarding table which has exceeded the limit number of MAC addresses, the system will generate the following notifications. syslog(1) : An syslog message will be generated to users. snmpNotif(2) : An SNMP notification message will be generated to users. both(3) : Both a syslog message and an SNMP notification message will be generated to users.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER sysLog(1), snmpNotif(2), both(3)  

clcMacLimitNotifEnable 1.3.6.1.4.1.9.9.313.1.1.5
The MIB object controls generation of SNMP notification for MAC Limit feature. When this object is 'true', generation of clcVlanMacLimitNotif is enabled. When this object is 'false', generation of clcVlanMacLimitNotif is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clcVlanMacLimitTable 1.3.6.1.4.1.9.9.313.1.1.6
The table contains information on Vlan MAC address limit feature for each VLAN capable of this feature.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClcVlanMacLimitEntry

clcVlanMacLimitEntry 1.3.6.1.4.1.9.9.313.1.1.6.1
An entry contains Vlan MAC address limit feature configuration for the VLAN
Status: current Access: not-accessible
OBJECT-TYPE    
  ClcVlanMacLimitEntry  

clcVlanMacLimitIndex 1.3.6.1.4.1.9.9.313.1.1.6.1.1
The VLAN ID for each VLAN's configuration of MAC address limit function in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4096  

clcVlanMacLimitGlobalConfig 1.3.6.1.4.1.9.9.313.1.1.6.1.2
This object indicates whether the configurations for this VLAN are based on the corresponding global default configurations or not. vlanMaxMacLimit(0) : indicates that the value of clcVlanMaxMacLimit is based on the value of clcMaxMacLimitDefault if this bit is set. vlanLimitExceededAction(1) : indicates that the value of clcVlanMacLimitExceededAction is based on the value of clcMacLimitExceededActionDefault if this bit is set. vlanMacLimitHigh(2) : indicates that the value of clcVlanMacLimitHigh is based on the value of clcMacLimitHighDefault if this bit is set. vlanLimitHighExceededAction(3) : indicates that the value of clcVlanMacLimitHighExceedAction is based on the value of clcMacLimitHighExceedActionDef if this bit is set.
Status: current Access: read-only
OBJECT-TYPE    
  BITS vlanMaxMacLimit(0), vlanLimitExceededAction(1), vlanMacLimitHigh(2), vlanLimitHighExceededAction(3)  

clcVlanMaxMacLimit 1.3.6.1.4.1.9.9.313.1.1.6.1.3
The lower threshold limit number of MAC addresses entries for this VLAN. When the instance value of this object is set to 0, no lower threshold limit will be applied for this Vlan and the corresponding instance value of clcVlanMacLimitExceededAction of the same row has no effect. The default value of this object is the value of clcMaxMacLimitDefault.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

clcVlanMacLimitExceededAction 1.3.6.1.4.1.9.9.313.1.1.6.1.4
The action to be taken by the system for this VLAN while the number of MAC addresses has exceeded the value of clcVlanMaxMacLimit. This object value is only effective when the corresponding instance value of clcVlanMaxMacLimit is not set to 0. The default value of this MIB object is the value of clcMacLimitExceededActionDefault.
Status: current Access: read-create
OBJECT-TYPE    
  MacLimitExceededAction  

clcVlanMacLimitStatus 1.3.6.1.4.1.9.9.313.1.1.6.1.5
This object is a conceptual row entry that allows to add or delete entries to or from the clcVlanMacLimitTable. 1. When creating an entry in this table 'createAndGo' method is used and the value of this object is set to 'active'. Deactivation of an 'active' entry is not allowed. 2. When deleting an entry in this table 'destroy' method is used. The value of clcVlanMaxMacLimit, clcVlanMacLimitExceededAction, clcVlanMacLimitEnable, clcVlanMacLimitHigh and clcVlanMacLimitHighExceedAction object can be modified when the value of this RowStatus object is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

clcVlanMacLimitEnable 1.3.6.1.4.1.9.9.313.1.1.6.1.6
This object indicates whether the Mac Limit feature is enabled on this Vlan or not.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

clcVlanMacLimitHigh 1.3.6.1.4.1.9.9.313.1.1.6.1.7
The higher threshold limit for the number of MAC addresses entries on this VLAN. The instance value of this clcVlanMacLimitHigh must be greater than the instance value of the clcVlanMaxMacLimit of the same row, only when the value is not zero. When the instance value of this object is set to 0, no higher threshold limit will be applied for this Vlan and the corresponding instance value of clcVlanMacLimitHighExceededAction of the same row has no effect. The default value of this MIB object is the value of clcMacLimitHighDefault.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

clcVlanMacLimitHighExceedAction 1.3.6.1.4.1.9.9.313.1.1.6.1.8
The action to be taken by the system for this Vlan while the number of MAC addresses has exceeded the value of clcVlanMacLimitHigh. This object value is only effective when the corresponding instance value of clcVlanMacLimitHigh is not set to 0. The default value of this MIB object is the value of clcMacLimitHighExceedActionDef.
Status: current Access: read-create
OBJECT-TYPE    
  MacLimitExceededAction  

clcFdbVlanInfoTable 1.3.6.1.4.1.9.9.313.1.1.7
The table contains VLAN information of forwarding tables in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClcFdbVlanInfoEntry

clcFdbVlanInfoEntry 1.3.6.1.4.1.9.9.313.1.1.7.1
An entry contains the information of a VLAN in a specific forwarding table. Each forwarding table will be identified by the entity physical index.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClcFdbVlanInfoEntry  

clcFdbVlanMacUsage 1.3.6.1.4.1.9.9.313.1.1.7.1.1
The usage of the MAC addresses in the specific forwarding table for this VLAN. It indicates the number of MAC addresses in this VLAN for a forwarding table.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clcMacLimitInterval 1.3.6.1.4.1.9.9.313.1.1.8
Specifies the interval at which forwarding table is monitored.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

clcMacLimitHighDefault 1.3.6.1.4.1.9.9.313.1.1.9
The global default value for high threshold limit number of MAC addresses in the system. The value of clcMacLimitHighDefault must be greater than the value of clcMaxMacLimitDefault.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

clcMacLimitHighExceedActionDef 1.3.6.1.4.1.9.9.313.1.1.10
The global default action to be taken by the system when the number of MAC addresses in the forwarding table has exceeded the high threshold number of MAC address limit for a VLAN or for a interface or for interface-VLAN pair.
Status: current Access: read-write
OBJECT-TYPE    
  MacLimitExceededAction  

clcMacLimitHighNotifEnable 1.3.6.1.4.1.9.9.313.1.1.11
The MIB object controls generation of SNMP notification for Vlan MAC Limit feature. When this object is 'true', generation of clcVlanMacLimitHighNotif is enabled. When this object is 'false', generation of clcVlanMacLimitHighNotif is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clcUnicastFloodTable 1.3.6.1.4.1.9.9.313.1.2.1
This table contains information about the unicast flooding on the system. The number of entries is determined by the number of interfaces in the system that can support the unicast flooding feature. Only L2 interfaces can support unicast flooding.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClcUnicastFloodEntry

clcUnicastFloodEntry 1.3.6.1.4.1.9.9.313.1.2.1.1
An entry contains the information about the unicast flooding for a particular interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClcUnicastFloodEntry  

clcUnicastFloodAdminEnable 1.3.6.1.4.1.9.9.313.1.2.1.1.1
This object indicates whether the configuration of the unicast flooding is enabled or disabled on a particular interface. If this object is 'true', then the unicast flooding has been configured to enabled. If this object is 'false', then the unicast flooding has been configured to disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clcUnicastFloodOperEnable 1.3.6.1.4.1.9.9.313.1.2.1.1.2
This object indicates the operational status of the unicast flooding on an interface, whether it is enabled or not. If this object is 'true', then the interface is unicast flooding. If this object is 'false', then the interface is not unicast flooding.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

clcIfMacLimitTable 1.3.6.1.4.1.9.9.313.1.3.1
The table contains information on Interface MAC address limit feature for each interface capable of this feature.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClcIfMacLimitEntry

clcIfMacLimitEntry 1.3.6.1.4.1.9.9.313.1.3.1.1
An entry contains Interface MAC address limit feature configuration for the Interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClcIfMacLimitEntry  

clcIfMacLimitIfIndex 1.3.6.1.4.1.9.9.313.1.3.1.1.1
The value of ifIndex for the configuration of MAC address limit function on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

clcIfMacLimitEnable 1.3.6.1.4.1.9.9.313.1.3.1.1.2
This object indicates whether the Mac Limit feature is enabled on this interface or not.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

clcIfMacLimitGlobalConfig 1.3.6.1.4.1.9.9.313.1.3.1.1.3
This object indicates whether the configurations for this interface are based on the corresponding global default configurations or not. ifMacLimitLow(0) : indicates that the value of clcIfMacLimitLow is based on the value of clcMaxMacLimitDefault if this bit is set. ifLimitLowExceededAction(1) : indicates that the value of clcIfMacLimitLowExceedAction is based on the value of clcMacLimitExceededActionDefault if this bit is set. ifMacLimitHigh(2) : indicates that the value of clcIfMacLimitHigh is based on the value of clcMacLimitHighDefault if this bit is set. ifLimitHighExceededAction(3) : indicates that the value of clcIfMacLimitHighExceedAction is based on the value of clcMacLimitHighExceedActionDef if this bit is set.
Status: current Access: read-only
OBJECT-TYPE    
  BITS ifMacLimitLow(0), ifLimitLowExceededAction(1), ifMacLimitHigh(2), ifLimitHighExceededAction(3)  

clcIfMacLimitLow 1.3.6.1.4.1.9.9.313.1.3.1.1.4
The lower threshold limit for the number of MAC addresses entries on this interface. When the instance value of this object is set to 0, no lower threshold limit will be applied for this Vlan and the corresponding instance value of clcIfMacLimitLowExceedAction of the same row has no effect. The default value of this MIB object is the value of clcMaxMacLimitDefault.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

clcIfMacLimitLowExceedAction 1.3.6.1.4.1.9.9.313.1.3.1.1.5
The action to be taken by the system for this interface while the number of MAC addresses has exceeded the value of clcMaxIfMacLimitLow. This object value is only effective when the corresponding instance value of clcIfMacLimitLow is not set to 0. The default value of this MIB object is the value of clcMacLimitExceededActionDefault.
Status: current Access: read-create
OBJECT-TYPE    
  MacLimitExceededAction  

clcIfMacLimitHigh 1.3.6.1.4.1.9.9.313.1.3.1.1.6
The higher threshold limit for the number of MAC addresses entries on this interface. The instance value of this clcIfMacLimitHigh must be greater than the instance value of the clcIfMacLimitLow of the same row, only when the value is not zero. When the instance value of this object is set to 0, no higher threshold limit will be applied for this Vlan and the corresponding instance value of clcIfMacLimitHighExceedAction of the same row has no effect. The default value of this MIB object is the value of clcMacLimitHighDefault.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

clcIfMacLimitHighExceedAction 1.3.6.1.4.1.9.9.313.1.3.1.1.7
The action to be taken by the system for this interface while the number of MAC addresses has exceeded the value of clcIfMacLimitHigh. This object value is only effective when the corresponding instance value of clcIfMacLimitHigh is not set to 0. The default value of this MIB object is the value of clcMacLimitHighExceedActionDef.
Status: current Access: read-create
OBJECT-TYPE    
  MacLimitExceededAction  

clcIfMacLimitStatus 1.3.6.1.4.1.9.9.313.1.3.1.1.8
This object is a conceptual row entry that allows to add or delete entries to or from the clcIfMacLimitTable. 1. When creating an entry in this table 'createAndGo' method is used and the value of this object is set to 'active'. Deactivation of an 'active' entry is not allowed. 2. When deleting an entry in this table 'destroy' method is used. The value of clcIfMacLimitEnable , clcIfMacLimitLow, clcIfMacLimitLowExceedAction, clcIfMacLimitHigh and clcIfMacLimitHighExceedAction object can be modified when the value of this RowStatus object is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

clcFdbIfInfoTable 1.3.6.1.4.1.9.9.313.1.3.2
The table contains interface information of forwarding tables in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClcFdbIfInfoEntry

clcFdbIfInfoEntry 1.3.6.1.4.1.9.9.313.1.3.2.1
An entry contains the information of a interface in a specific forwarding table. Each forwarding table will be identified by the entity physical index.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClcFdbIfInfoEntry  

clcFdbIfMacUsage 1.3.6.1.4.1.9.9.313.1.3.2.1.1
The usage of the MAC addresses in the specific forwarding table for this interface. It indicates the number of MAC addresses learnt or configured on this interface for a forwarding table.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clcIfMacLimitLowNotifEnable 1.3.6.1.4.1.9.9.313.1.3.3
Specifies whether the generation of a specified notification for interface MAC Limit feature is enabled or not. When this object is 'true', generation of clcIfMacLimitLowNotif is enabled. When this object is 'false', generation of clcIfMacLimitLowNotif is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clcIfMacLimitHighNotifEnable 1.3.6.1.4.1.9.9.313.1.3.4
Specifies whether the generation of a specified notification for interface MAC Limit feature is enabled or not. When this object is 'true', generation of clcIfMacLimitHighNotif is enabled. When this object is 'false', generation of clcIfMacLimitHighNotif is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clcIfVlanMacLimitTable 1.3.6.1.4.1.9.9.313.1.4.1
The table contains information on Interface Vlan MAC address limit feature for each interface-VLAN pair capable of this feature.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClcIfVlanMacLimitEntry

clcIfVlanMacLimitEntry 1.3.6.1.4.1.9.9.313.1.4.1.1
An entry contains Interface Vlan MAC address limit feature configuration for the Interface and Vlan.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClcIfVlanMacLimitEntry  

clcIfVlanMacLimitIfIndex 1.3.6.1.4.1.9.9.313.1.4.1.1.1
The value of ifIndex for the configuration of MAC address limit function on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

clcIfVlanMacLimitVlanIndex 1.3.6.1.4.1.9.9.313.1.4.1.1.2
The VLAN ID for each VLAN's configuration of MAC address limit function in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanIndex  

clcIfVlanMacLimitEnable 1.3.6.1.4.1.9.9.313.1.4.1.1.3
This object indicates whether the Mac Limit feature is enabled on this interface-Vlan pair or not.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

clcIfVlanMacLimitGlobalConfig 1.3.6.1.4.1.9.9.313.1.4.1.1.4
This object indicates whether the configurations for this interface are based on the corresponding global default configurations or not. ifVlanMacLimitLow(0) : indicates that the value of clcIfVlanMacLimitLow is based on the value of clcMaxMacLimitDefault if this bit is set. ifVlanLimitLowExceededAction(1) : indicates that the value of clcIfVlanMacLimitLowExceedAction is based on the value of clcMacLimitExceededActionDefault if this bit is set. ifVlanMacLimitHigh(2) : indicates that the value of clcIfVlanMacLimitHigh is based on the value of clcMacLimitHighDefault if this bit is set. ifVlanLimitHighExceededAction(3) : indicates that the value of clcIfVlanMacLimitHiExceedAction is based on the value of clcMacLimitHighExceedActionDef if this bit is set.
Status: current Access: read-only
OBJECT-TYPE    
  BITS ifVlanMacLimitLow(0), ifVlanLimitLowExceededAction(1), ifVlanMacLimitHigh(2), ifVlanLimitHighExceededAction(3)  

clcIfVlanMacLimitLow 1.3.6.1.4.1.9.9.313.1.4.1.1.5
The lower threshold limit for the number of MAC addresses entries on this interface and Vlan. When the instance value of this object is set to 0, no lower threshold limit will be applied for this Vlan and the corresponding instance value of clcIfVlanMacLimitLowExceedAction of the same row has no effect. The default value of this MIB object is the value of clcMaxMacLimitDefault.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

clcIfVlanMacLimitLowExceedAction 1.3.6.1.4.1.9.9.313.1.4.1.1.6
The action to be taken by the system for this interface Vlan while the number of MAC addresses has exceeded the value of clcIfVlanMacLimitLow. This object value is only effective when the corresponding instance value of clcIfVlanMacLimitLow is not set to 0. The default value of this MIB object is the value of clcMacLimitExceededActionDefault.
Status: current Access: read-create
OBJECT-TYPE    
  MacLimitExceededAction  

clcIfVlanMacLimitHigh 1.3.6.1.4.1.9.9.313.1.4.1.1.7
The higher threshold limit for the number of MAC addresses entries on this interface and Vlan. The instance value of this clcIfVlanMacLimitHigh must be greater than the instance value of the clcIfVlanMacLimitLow of the same row, only when the value is not zero. When the instance value of this object is set to 0, no higher threshold limit will be applied for this Vlan and the corresponding instance value of clcIfVlanMacLimitHiExceedAction of the same row has no effect. The default value of this MIB object is the value of clcMacLimitHighDefault.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

clcIfVlanMacLimitHiExceedAction 1.3.6.1.4.1.9.9.313.1.4.1.1.8
The action to be taken by the system for this interface and Vlan while the number of MAC addresses has exceeded the value of clcIfVlanMacLimitHigh. This object value is only effective when the corresponding instance value of clcIfVlanMacLimitHigh is not set to 0. The default value of this MIB object is the value of clcMacLimitHighExceedActionDef.
Status: current Access: read-create
OBJECT-TYPE    
  MacLimitExceededAction  

clcIfVlanMacLimitStatus 1.3.6.1.4.1.9.9.313.1.4.1.1.9
This object is a conceptual row entry that allows to add or delete entries to or from the clcIfVlanMacLimitTable. 1. When creating an entry in this table 'createAndGo' method is used and the value of this object is set to 'active'. Deactivation of an 'active' entry is not allowed. 2. When deleting an entry in this table 'destroy' method is used. The value of clcIfVlanMacLimitEnable , clcIfVlanMacLimitLow, clcIfVlanMacLimitLowExceedAction, clcIfVlanMacLimitHigh and clcIfVlanMacLimitHiExceedAction object can be modified when the value of this RowStatus object is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

clcFdbIfVlanInfoTable 1.3.6.1.4.1.9.9.313.1.4.2
The table contains interface information of forwarding tables in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClcFdbIfVlanInfoEntry

clcFdbIfVlanInfoEntry 1.3.6.1.4.1.9.9.313.1.4.2.1
An entry contains the information of a interface-VLAN pair in a specific forwarding table. Each forwarding table will be identified by the entity physical index.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClcFdbIfVlanInfoEntry  

clcFdbIfVlanMacUsage 1.3.6.1.4.1.9.9.313.1.4.2.1.1
The usage of the MAC addresses in the specific forwarding table for this interface and Vlan. It indicates the number of MAC addresses learnt or configured on this interface and VLAN for a forwarding table.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clcIfVlanMacLimitLowNotifEnable 1.3.6.1.4.1.9.9.313.1.4.3
Spcifies whether the generation of a specified notification for interface Vlan MAC Limit feature is enabled or not. When this object is 'true', generation of clcIfVlanMacLimitLowNotif is enabled. When this object is 'false', generation of clcIfVlanMacLimitLowNotif is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clcIfVlanMacLimitHighNotifEnable 1.3.6.1.4.1.9.9.313.1.4.4
Spcifies whether the generation of a specified notification for interface Vlan MAC Limit feature is enabled or not. When this object is 'true', generation of clcIfVlanMacLimitHighNotif is enabled. When this object is 'false', generation of clcIfVlanMacLimitHighNotif is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clcFdbMacAddressStatsTable 1.3.6.1.4.1.9.9.313.1.5.1
The table contains statistics information for different type of MAC addresses in the forwarding table of the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClcFdbMacAddressStatsEntry

clcFdbMacAddressStatsEntry 1.3.6.1.4.1.9.9.313.1.5.1.1
An entry contains statistics information for a specific MAC addresse type in the forwarding table of the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClcFdbMacAddressStatsEntry  

clcFdbMacAddressStatsType 1.3.6.1.4.1.9.9.313.1.5.1.1.1
This object indicates a specific MAC address statistics type.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClcMacAddressStatsType  

clcFdbMacAddressStatsNumber 1.3.6.1.4.1.9.9.313.1.5.1.1.2
This object indicates the number of a particular type of MAC address in the forwarding table.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clcVlanMacLimitNotif 1.3.6.1.4.1.9.9.313.0.1
Notification is sent when the number of MAC addresses (the value of clcFdbVlanMacUsage) has crossed the configured limit of MAC addresses(clcVlanMaxMacLimit) either rising above or falling below it.
Status: current Access: read-only
NOTIFICATION-TYPE    

clcVlanMacLimitHighNotif 1.3.6.1.4.1.9.9.313.0.2
Notification is sent when the number of MAC addresses (the value of clcFdbVlanMacUsage) has crossed the configured higher threshold limit of MAC addresses(clcVlanMacLimitHigh) either rising above or falling below it.
Status: current Access: read-only
NOTIFICATION-TYPE    

clcIfMacLimitLowNotif 1.3.6.1.4.1.9.9.313.0.3
Notification is sent when the number of MAC addresses (the value of clcFdbIfMacUsage) has crossed the configured lower threshold limit of MAC addresses(clcIfMacLimitLow) either rising above or falling below it.
Status: current Access: read-only
NOTIFICATION-TYPE    

clcIfMacLimitHighNotif 1.3.6.1.4.1.9.9.313.0.4
Notification is sent when the number of MAC addresses (the value of clcFdbIfMacUsage) has crossed the configured higher threshold limit of MAC addresses(clcIfMacLimitHigh) either rising above or falling below it.
Status: current Access: read-only
NOTIFICATION-TYPE    

clcIfVlanMacLimitLowNotif 1.3.6.1.4.1.9.9.313.0.5
Notification is sent when the number of MAC addresses (the value of clcFdbIfVlanMacUsage) has crossed the configured lower threshold limit of MAC addresses(clcIfVlanMacLimitLow) either rising above or falling below it.
Status: current Access: read-only
NOTIFICATION-TYPE    

clcIfVlanMacLimitHighNotif 1.3.6.1.4.1.9.9.313.0.6
Notification is sent when the number of MAC addresses (the value of clcFdbIfVlanMacUsage) has crossed the configured higher threshold limit of MAC addresses(clcIfVlanMacLimitHigh) either rising above or falling below it.
Status: current Access: read-only
NOTIFICATION-TYPE    

ciscoL2ControlMIBCompliances 1.3.6.1.4.1.9.9.313.2.1
OBJECT IDENTIFIER    

ciscoL2ControlMIBGroups 1.3.6.1.4.1.9.9.313.2.2
OBJECT IDENTIFIER    

ciscoL2ControlMIBCompliance 1.3.6.1.4.1.9.9.313.2.1.1
The compliance statement for entities which implement the L2 Control MIB.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoL2ControlMIBCompliance2 1.3.6.1.4.1.9.9.313.2.1.2
The compliance statement for entities which implement the L2 Control MIB.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoL2ControlMIBCompliance3 1.3.6.1.4.1.9.9.313.2.1.3
The compliance statement for entities which implement the L2 Control MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

clcMacAddressLimitGroup 1.3.6.1.4.1.9.9.313.2.2.1
This is the group to control MAC address limit function.
Status: current Access: read-only
OBJECT-GROUP    

clcVlanMacAddressLimitGroup 1.3.6.1.4.1.9.9.313.2.2.2
This is the group to control VLAN MAC address limit function.
Status: current Access: read-only
OBJECT-GROUP    

clcVlanMacLimitNotifsGroup 1.3.6.1.4.1.9.9.313.2.2.3
The collection of notifications used to indicate that the number of MAC addresses has crossed the configured limit of MAC addresses either rising above or falling below it.
Status: current Access: read-only
NOTIFICATION-GROUP    

clcUnicastFloodGroup 1.3.6.1.4.1.9.9.313.2.2.4
This is the group to control unicast flooding.
Status: current Access: read-only
OBJECT-GROUP    

clcMacAddressLimitIntervalGroup 1.3.6.1.4.1.9.9.313.2.2.5
This is the group to control MAC address limit interval.
Status: current Access: read-only
OBJECT-GROUP    

clcMacAddressLimitGroup1 1.3.6.1.4.1.9.9.313.2.2.6
This group is to control additional global MAC address limit function.
Status: current Access: read-only
OBJECT-GROUP    

clcVlanMacAddressLimitGroup1 1.3.6.1.4.1.9.9.313.2.2.7
This is the group to control additional VLAN MAC address limit function.
Status: current Access: read-only
OBJECT-GROUP    

clcVlanMacLimitEnableGroup 1.3.6.1.4.1.9.9.313.2.2.8
This is the group to control per vlan MAC limit enable/disable configuration.
Status: current Access: read-only
OBJECT-GROUP    

clcVlanMacLimitNotifControlGroup 1.3.6.1.4.1.9.9.313.2.2.9
This is the group to control vlan MAC limit notification configuration.
Status: current Access: read-only
OBJECT-GROUP    

clcVlanMacLimitNotifControlGroup1 1.3.6.1.4.1.9.9.313.2.2.10
This is the group to control high vlan MAC limit notification configuration.
Status: current Access: read-only
OBJECT-GROUP    

clcVlanMacLimitNotifsGroup1 1.3.6.1.4.1.9.9.313.2.2.11
The collection of notifications used to indicate that the number of MAC addresses has crossed the configured high limit of MAC addresses for the VLAN either rising above or falling below it.
Status: current Access: read-only
NOTIFICATION-GROUP    

clcIfMacAddressLimitGroup 1.3.6.1.4.1.9.9.313.2.2.12
This is the group to control Interface MAC address limit function.
Status: current Access: read-only
OBJECT-GROUP    

clcIfMacLimitEnableGroup 1.3.6.1.4.1.9.9.313.2.2.13
This is the group to control per interface MAC limit enable/disable configuration.
Status: current Access: read-only
OBJECT-GROUP    

clcIfMacLimitNotifControlGroup 1.3.6.1.4.1.9.9.313.2.2.14
This is the group to control interface MAC limit notification configuration.
Status: current Access: read-only
OBJECT-GROUP    

clcIfMacLimitNotifsGroup 1.3.6.1.4.1.9.9.313.2.2.15
The collection of notifications used to indicate that the number of MAC addresses has crossed the configured limit of MAC addresses for an interface either rising above or falling below it.
Status: current Access: read-only
NOTIFICATION-GROUP    

clcIfVlanMacAddressLimitGroup 1.3.6.1.4.1.9.9.313.2.2.16
This is the group to control Interfcae and Vlan MAC address limit function.
Status: current Access: read-only
OBJECT-GROUP    

clcIfVlanMacLimitEnableGroup 1.3.6.1.4.1.9.9.313.2.2.17
This is the group to control per interface Vlan MAC limit enable/disable configuration.
Status: current Access: read-only
OBJECT-GROUP    

clcIfVlanMacLimitNotifControlGroup 1.3.6.1.4.1.9.9.313.2.2.18
This is the group to control per interface Vlan MAC limit notification configuration.
Status: current Access: read-only
OBJECT-GROUP    

clcIfVlanMacLimitNotifsGroup 1.3.6.1.4.1.9.9.313.2.2.19
The collection of notifications used to indicate that the number of MAC addresses has crossed the configured limit of MAC addresses for a given VLAN and interface either rising above or falling below it.
Status: current Access: read-only
NOTIFICATION-GROUP    

clcMacAddressStatsGroup 1.3.6.1.4.1.9.9.313.2.2.20
A collection of objects that provides the MAC address statistics based on the type of MAC addresses.
Status: current Access: read-only
OBJECT-GROUP