CISCO-ITP-GSP-MIB

File: CISCO-ITP-GSP-MIB.mib (222763 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMP-FRAMEWORK-MIB
INET-ADDRESS-MIB IF-MIB SNMPv2-TC
CISCO-ITP-TC-MIB CISCO-SMI

Imported symbols

Counter32 Integer32 Gauge32
MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE
Unsigned32 MODULE-COMPLIANCE NOTIFICATION-GROUP
OBJECT-GROUP SnmpAdminString InetAddressType
InetAddress InetPortNumber InterfaceIndexOrZero
RowStatus TimeStamp TruthValue
TEXTUAL-CONVENTION CItpTcAclId CItpTcCLLI
CItpTcDisplayPC CItpTcInstanceNumber CItpTcLinksetId
CItpTcNetworkName CItpTcLinkSLC CItpTcLinkType
CItpTcNetworkIndicator CItpTcPointCode CItpTcPointCodeType
CItpTcQos CItpTcRouteTableName CItpTcServiceIndicator
ciscoMgmt

Defined Types

CgspSequenceNumber  
This textual convention defines all of the allowed values for a sequence of integers used by the SS7 protocol to transmit and acknowledge packets. The range is specified from 0 to maximum allowed value for extended sequence numbers. The actual range will depend on the type of link and the variant. The value will increase and then wrap to the zero value. The following are examples of valid sequences. 0..126,127,0.. 0..254,255,0.. 0..32766,32767,0.. 0..65534,65535,0.. Therefore, the sequence number will behave like a counter with range appropriate for the type of link.
TEXTUAL-CONVENTION    
  Unsigned32 0..65535  

CgspSampleInterval  
This textual convention defines the allowed values for a sample interval. This value is specified in seconds and ranges from 1 minute to 1 hour.
TEXTUAL-CONVENTION    
  Unsigned32 60..3600  

CgspPercentThreshold  
This textual convention defines the allowed values used to define a threshold. This value is specified as percentage of link utilization. A value of zero indicates that this specific threshold is to be ignored.
TEXTUAL-CONVENTION    
  Unsigned32 0..100  

CgspLinkTestResults  
This object provides information on result from signalling link test procedures as follows. 'noErrors' : Link test did not detect any errors. 'undefinedOpc' : A signalling link test message was received with an undefined originating point code. 'incorrectOpc' : A signalling link test message was received with an incorrect originating point code. 'undefinedSlc' : A signalling link test message was received with an undefined signalling link code. 'incorrectSlc' : A signalling link test message was received with an incorrect signalling link code.. 'incorrectNi' : A signalling link test message was received with an incorrect Network Indicator. 'badPattern' : A signalling link test message was received with an incorrect test pattern. This may be caused by variant mismatched or incorrect definitions on physical link. 'nonAdjacent' :Received a signalling link test message from an non-adjacent node. 'failed' :Unable to run test or no response was received within the specified interval.
TEXTUAL-CONVENTION    
  INTEGER noErrors(0), undefinedOpc(1), incorrectOpc(2), undefinedSlc(3), incorrectSlc(4), incorrectNi(5), badPattern(6), nonAdjacent(7), failed(8)  

CgspLinkUtilization  
This textual convention defines a range of values that represent a link's utilization during an interval of time. The values expressed as a percent of link capacity. Any value over 999 will be represented as 999. For SS7 links based on IP/SCTP the link capacity is not directly related to the interface speed used to transmit packets. This is different from serial and HSL links. The capacity of these types of links depend on the amount of resources available in the IP cloud. The IP cloud must be provisioned to support traffic for all SS7 links. In order to monitor link utilization on IP/SCTP based SS7 links a planned capacity must be specified. If this value is incorrectly estimated or traffic exceeds this expected value link utilization may exceed 100 percent. This is possible because the IP cloud may be provisioned with additional capacity or may discard less important traffic based on QoS parameters. When a SS7 link has not be configured for link utilization monitoring this value object will have a value of zero.
TEXTUAL-CONVENTION    
  Gauge32 0..999  

CgspLinkCapacity  
This textual convention defines the planned capacity of a SS7 link in bit per second. When the cgspLinkType object is 'sctpIp' or 'hsl' the link capacity can be obtained from information in the IF-MIB. When the cgspLinkType object is 'sctpIp' a value of zero indicates that link utilization should not be calculated for this SS7 link.
TEXTUAL-CONVENTION    
  Unsigned32 0..0 | 56000..2147483647  

CgspProfileName  
The configured name associated with a Signalling Point Profile. An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..19)  

CgspLinkUtilizationState  
Link Utilization State as follows: 'unMonitored' - traffic for a specified direction is not being monitored. 'underThreshold' - traffic for a specified direction on a link is below the specified threshold. 'overThreshold' - traffic for a specified direction on a link is above to or exceeds the specified threshold.
TEXTUAL-CONVENTION    
  INTEGER unMonitored(0), underThreshold(1), overThreshold(2)  

CgspTimerNumbers  
Enumerated values for all timers
TEXTUAL-CONVENTION    
  INTEGER timerMtp3T01(1), timerMtp3T02(2), timerMtp3T03(3), timerMtp3T04(4), timerMtp3T05(5), timerMtp3T06(6), timerMtp3T07(7), timerMtp3T08(8), timerMtp3T09(9), timerMtp3T10(10), timerMtp3T11(11), timerMtp3T12(12), timerMtp3T13(13), timerMtp3T14(14), timerMtp3T15(15), timerMtp3T16(16), timerMtp3T17(17), timerMtp3T18(18), timerMtp3T19(19), timerMtp3T20(20), timerMtp3T21(21), timerMtp3T22(22), timerMtp3T23(23), timerMtp3T24(24), timerMtp3T25(25), timerMtp3T26(26), timerMtp3T27(27), timerMtp3T28(28), timerMtp3T29(29), timerMtp3T30(30), timerMtp3T31(31), timerMtp3T32(32), timerMtp3T33(33), timerMtp3T34(34), timerLinkTest(35), timerLinkMessag1(36), timerLinkActRetry(37), timerMtp2T01(38), timerMtp2T02(39), timerMtp2T03(40), timerMtp2T04N(41), timerMtp2T04E(42), timerMtp2T05(43), timerMtp2T06(44), timerMtp2T07(45)  

CgspTimerValue  
Value of timers in milliseconds as follows. A value of zero indicates that the timer is not applicable for variant or link type. The values specified in this textual convention apply to the various timers identified in CgspTimerNumbers textual convention. ANSI ITU Min Max Def Min Max Def ------ ------ ------ ------ ------ ------ TimerMtp3T01 500 1200 800 500 1200 800 TimerMtp3T02 700 2000 1400 700 2000 1400 TimerMtp3T03 500 1200 800 500 1200 800 TimerMtp3T04 500 1200 800 500 1200 800 TimerMtp3T05 500 1200 800 500 1200 800 TimerMtp3T06 500 1200 800 500 1200 800 TimerMtp3T07 1000 2000 1500 1000 2000 1500 TimerMtp3T08 800 1200 1000 800 1200 1000 TimerMtp3T10 30000 60000 45000 30000 60000 45000 TimerMtp3T11 30000 90000 60000 30000 90000 60000 TimerMtp3T12 800 1500 1150 800 1500 1150 TimerMtp3T13 800 1500 1150 800 1500 1150 TimerMtp3T14 2000 3000 2500 2000 3000 2500 TimerMtp3T15 2000 3000 2500 2000 3000 2500 TimerMtp3T16 1400 2000 1700 1400 2000 1700 TimerMtp3T17 800 1500 1150 800 1500 1150 TimerMtp3T18 2000 20000 11000 1000 31000 30000 TimerMtp3T19 480000 600000 540000 67000 69000 68000 TimerMtp3T20 90000 120000 105000 1000 61000 60000 TimerMtp3T21 90000 120000 105000 63000 65000 64000 TimerMtp3T22 36000 60000 30000 80000 360000 300000 TimerMtp3T23 9000 60000 30000 80000 360000 300000 TimerMtp3T24 9000 60000 30000 500 500 500 TimerMtp3T25 30000 35000 30000 n/a n/a n/a TimerMtp3T26 12000 15000 12000 n/a n/a n/a TimerMtp3T27 2000 50000 4000 n/a n/a n/a TimerMtp3T28 3000 35000 30000 n/a n/a n/a TimerMtp3T29 60000 65000 63000 n/a n/a n/a TimerMtp3T30 30000 35000 33000 n/a n/a n/a TimerMtp3T31 10000 120000 60000 n/a n/a n/a TimerMtp3T32 5000 120000 60000 n/a n/a n/a TimerMtp3T33 60000 600000 300000 n/a n/a n/a TimerMtp3T34 5000 120000 60000 n/a n/a n/a TimerLinkTest 4000 12000 8000 n/a n/a n/a TimerLinkMessage 30000 90000 60000 n/a n/a n/a TimerLinkActRetry 60000 90000 60000 n/a n/a n/a
TEXTUAL-CONVENTION    
  Unsigned32 0..0 | 1..4294967295  

CgspSS7Variant  
The list of SS7 variants. 'unknown' : Unknown or undefined variant. 'ANSI' : The ANSI variant of the SS7 specification. 'ITU' : The ITU variant of the SS7 specification. 'China' : The China national variant. This variant is a combination of ITU and ANSI. The protocol matches ITU except where the point-code has been expanded to ANSI format. 'NTT' : The Japanese Nippon Telephone & Telegraph variant. 'TTC' : The Japanese Telecommunications Technology Committee variant.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), ansi(1), itu(2), china(3), ntt(4), ttc(5)  

CgspDisplayInstanceUserPart  
The instance name and user part information formatted for display. If instance name is not configured, the default local point code in ASCII string format will be provided as instance name.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..40)  

CItpTcSccpWrrOption  
The possible options for calculate sccp class1 traffic loadshare when GTT application group's multiplicity mode is WRR(Weighted round robin): 'sls' : Use sls to calculate loadsharing 'cgpaSls' : Use the combination of cgpa and sls to calculate loadsharing 'opcSls' : Use the combination of opc and sls to calculate loadsharing 'opc' : Use the opc to caculate loadsharing
TEXTUAL-CONVENTION    
  INTEGER sls(0), cgpaSls(1), opcSls(2), opc(3)  

CgspProfileTableEntry  
SEQUENCE    
  cgspProfileName CgspProfileName
  cgspProfileVariant CgspSS7Variant
  cgspProfileMtp2BundleTimer Integer32
  cgspProfileMtp2SendQueueDepth Integer32
  cgspProfileRowStatus RowStatus

CgspProfileTimerTableEntry  
SEQUENCE    
  cgspProfileTimerNumber CgspTimerNumbers
  cgspProfileTimerValue CgspTimerValue
  cgspProfileTimerRowStatus RowStatus

CgspInstanceTableEntry  
SEQUENCE    
  cgspInstNetwork CItpTcNetworkName
  cgspInstNetworkIndicator CItpTcNetworkIndicator
  cgspInstVariant CgspSS7Variant
  cgspInstDisplayName SnmpAdminString
  cgspInstDescription SnmpAdminString
  cgspInstTFR TruthValue
  cgspInstCongestionsLevels TruthValue
  cgspInstFastRestart TruthValue
  cgspInstDistSccpUnseq TruthValue
  cgspInstSummaryRoutingException TruthValue
  cgspInstNumber CItpTcInstanceNumber
  cgspInstRouteTableName CItpTcRouteTableName
  cgspInstRowStatus RowStatus
  cgspInstSccpWrrOpcShift Unsigned32
  cgspInstSccpWrrOption CItpTcSccpWrrOption

CgspInstTimerTableEntry  
SEQUENCE    
  cgspInstTimerNumber CgspTimerNumbers
  cgspInstTimerValue CgspTimerValue
  cgspInstTimerRowStatus RowStatus

CgspInstUPUTableEntry  
SEQUENCE    
  cgspMtp3SI CItpTcServiceIndicator
  cgspInstSIUPUReceived Counter32
  cgspInstSIUPUTransmitted Counter32
  cgspInstUserPartDisplay CgspDisplayInstanceUserPart

CgspPointCodeTableEntry  
SEQUENCE    
  cgspPointCodeNi CItpTcNetworkIndicator
  cgspPointCodeBin CItpTcPointCode
  cgspPointCodeType CItpTcPointCodeType
  cgspPointCodeDisplay CItpTcDisplayPC
  cgspPointCodeRowStatus RowStatus

CgspLinksetTableEntry  
SEQUENCE    
  cgspLinksetName CItpTcLinksetId
  cgspLinksetSourcePointCode CItpTcPointCode
  cgspLinksetSourceDisplayPC CItpTcDisplayPC
  cgspLinksetAdjacentPointCode CItpTcPointCode
  cgspLinksetAdjacentDisplayPC CItpTcDisplayPC
  cgspLinksetState INTEGER
  cgspLinksetInboundAcl CItpTcAclId
  cgspLinksetOutboundAcl CItpTcAclId
  cgspLinksetAccountingMtp3 TruthValue
  cgspLinksetAccountingGtt TruthValue
  cgspLinksetNumLinks Unsigned32
  cgspLinksetDurationInService Counter32
  cgspLinksetDurationOutService Counter32
  cgspLinksetActPriority Unsigned32
  cgspLinksetDisplayName SnmpAdminString
  cgspLinksetDescription SnmpAdminString
  cgspLinksetRotateSlsEnable TruthValue
  cgspLinksetRotateSlsShift Unsigned32
  cgspLinksetProfileName CgspProfileName
  cgspLinksetAdjacentInst CItpTcNetworkName
  cgspLinksetRowStatus RowStatus

CgspLinksetTimerTableEntry  
SEQUENCE    
  cgspLinksetTimerNumber CgspTimerNumbers
  cgspLinksetTimerValue CgspTimerValue
  cgspLinksetTimerRowStatus RowStatus

CgspLinkTableEntry  
SEQUENCE    
  cgspLinkSlc CItpTcLinkSLC
  cgspLinkDescription SnmpAdminString
  cgspLinkState INTEGER
  cgspLinkReason INTEGER
  cgspLinkType CItpTcLinkType
  cgspLinkifIndex InterfaceIndexOrZero
  cgspLinkSctpAssociation Unsigned32
  cgspLinkXmitQueueDepth Gauge32
  cgspLinkXmitQueueDepthHigh Unsigned32
  cgspLinkXmitQueueDepthHighRT TimeStamp
  cgspLinkCongestionState Unsigned32
  cgspLinkCongestionAbate1 Unsigned32
  cgspLinkCongestionAbate2 Unsigned32
  cgspLinkCongestionAbate3 Unsigned32
  cgspLinkCongestionOnset1 Unsigned32
  cgspLinkCongestionOnset2 Unsigned32
  cgspLinkCongestionOnset3 Unsigned32
  cgspLinkSigLinkTest TruthValue
  cgspLinkQ752T1E1 Counter32
  cgspLinkQ752T1E2 Counter32
  cgspLinkQ752T1E3 Counter32
  cgspLinkQ752T1E5 Counter32
  cgspLinkQ752T1E7 Counter32
  cgspLinkQ752T1E8 Counter32
  cgspLinkQ752T1E9 Counter32
  cgspLinkQ752T1E10 Counter32
  cgspLinkQ752T1E11 Counter32
  cgspLinkQ752T2E1 Counter32
  cgspLinkQ752T2E5 Counter32
  cgspLinkQ752T2E6 Counter32
  cgspLinkQ752T2E7 Counter32
  cgspLinkQ752T2E9 Counter32
  cgspLinkQ752T2E10 Counter32
  cgspLinkQ752T2E15 Counter32
  cgspLinkQ752T2E16 Counter32
  cgspLinkQ752T2E18 Counter32
  cgspLinkQ752T3E1 Counter32
  cgspLinkQ752T3E2Bytes Counter32
  cgspLinkQ752T3E2Packets Counter32
  cgspLinkQ752T3E3 Counter32
  cgspLinkQ752T3E4 Counter32
  cgspLinkQ752T3E5 Counter32
  cgspLinkQ752T3E6 Counter32
  cgspLinkQ752T3E7 Counter32
  cgspLinkQ752T3E10L1 Counter32
  cgspLinkQ752T3E10L2 Counter32
  cgspLinkQ752T3E10L3 Counter32
  cgspLinkQ752T3E11L1 Counter32
  cgspLinkQ752T3E11L2 Counter32
  cgspLinkQ752T3E11L3 Counter32
  cgspLinkLocalPeerPort InetPortNumber
  cgspLinkRemotePeerPort InetPortNumber
  cgspLinkQosClass CItpTcQos
  cgspLinkDisplayName SnmpAdminString
  cgspLinkDroppedPkts Counter32
  cgspLinkTransmittedLSSUs Counter32
  cgspLinkReceivedLSSUs Counter32
  cgspLinkProtocolDetails BITS
  cgspLinkLsacState INTEGER
  cgspLinkTsrcState INTEGER
  cgspLinkTcocState INTEGER
  cgspLinkTcocLocalBSNT CgspSequenceNumber
  cgspLinkTcocRemoteBSNT CgspSequenceNumber
  cgspLinkTcbcState INTEGER
  cgspLinkReceivedSIBs Counter32
  cgspLinkTransmittedSIBs Counter32
  cgspLinkMtp2T01Counts Counter32
  cgspLinkMtp2T02Counts Counter32
  cgspLinkMtp2T03Counts Counter32
  cgspLinkMtp2T04Counts Counter32
  cgspLinkMtp2T05Counts Counter32
  cgspLinkMtp2T06Counts Counter32
  cgspLinkMtp2T07Counts Counter32
  cgspLinkOMAERMCounts Counter32
  cgspLinkOMAERMFailCounts Counter32
  cgspLinkOMSURMCounts Counter32
  cgspLinkOMSURMFailCounts Counter32
  cgspLinkPlanCapacityRcvd CgspLinkCapacity
  cgspLinkUtilThresholdRcvd CgspPercentThreshold
  cgspLinkUtilizationRcvd CgspLinkUtilization
  cgspLinkUtilStateRcvd CgspLinkUtilizationState
  cgspLinkL2BytesRcvd Counter32
  cgspLinkPlanCapacitySent CgspLinkCapacity
  cgspLinkUtilThresholdSent CgspPercentThreshold
  cgspLinkUtilizationSent CgspLinkUtilization
  cgspLinkUtilStateSent CgspLinkUtilizationState
  cgspLinkL2BytesSent Counter32
  cgspLinkTestResult CgspLinkTestResults
  cgspLinkRowStatus RowStatus
  cgspLinkSctpAssociationId Unsigned32
  cgspLinkQ752T1E12 Counter32
  cgspLinkQ752T1E12Errors Counter32
  cgspLinkQ752T2E11 Counter32
  cgspLinkQ752T2E17 Counter32
  cgspLinkQ752T2E19 Counter32
  cgspLinkRxCongestionState Unsigned32

CgspLinkTimerTableEntry  
SEQUENCE    
  cgspLinkTimerNumber CgspTimerNumbers
  cgspLinkTimerValue CgspTimerValue
  cgspLinkTimerRowStatus RowStatus

CgspLinkRemoteIpAddrTableEntry  
SEQUENCE    
  cgspLinkRemoteIpAddrNumber Unsigned32
  cgspLinkRemoteIpAddrType InetAddressType
  cgspLinkRemoteIpAddress InetAddress
  cgspLinkRemoteIpAddrRowStatus RowStatus

CgspLinkUtilTableEntry  
SEQUENCE    
  cgspLinkUtilIndex Unsigned32
  cgspLinkUtilRcvd CgspLinkUtilization
  cgspLinkUtilSent CgspLinkUtilization
  cgspLinkUtilEndTimestamp TimeStamp

Defined Values

ciscoGspMIB 1.3.6.1.4.1.9.9.336
The MIB for managing Signalling Points and its associated messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. This MIB replaces the CISCO-ITP-SP-MIB and provide support multiple instances of a signalling point within same configuration. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 Signalling point. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. This MIB models the GSP as follows: Abbreviations: AERM - Alignment Error Rate Monitor CLLI - Common-Language Location Identification DPC - Destination Point Code GSP - Gateway Signalling Point HSL - High Speed Link (ATM based) LLSC - link set control LSAC - Signalling link activity control LSDA - Signalling data link allocation LSLA - Signalling link activation LSLD - Signalling link deactivation LSLR - Signalling link restoration LSSU - Link Status Signal Unit LSTA - Signalling terminal allocation MTP - Message Transport Protocol MTP2 - Layer 2 of Message Transport Protocol MTP3 - Layer 3 of Message Transport Protocol NTT - The Japanese Nippon Telephone & Telegraph OPC - Originating Point Code PC - Point Code RTN - RouteTableName SCTP - Stream Transmission Protocol(RFC 2960) SIB - Status Indicator Busy SLT - Signalling Link Test SLTA - Signalling Link Test Acknowledgement SP - Signalling Point SS7 - System No. 7 (SS7) Network SUERM - Signal Unit Error Rate Monitor TCBC - Changeback control TCOC - Changeover control TCRC - Controlled rerouting control TFRC - Forced rerouting control TLAC - Link availability control TPRC - Signalling point restart control TRCC - Signalling route set congestion control TSFC - Signalling traffic flow control TSRC - Signalling routing control TTC - The Japanese Telecommunications Technology Committee WRR - Weighted round robin
MODULE-IDENTITY    

ciscoGspMIBNotifs 1.3.6.1.4.1.9.9.336.0
OBJECT IDENTIFIER    

ciscoGspMIBObjects 1.3.6.1.4.1.9.9.336.1
OBJECT IDENTIFIER    

ciscoGspMIBConform 1.3.6.1.4.1.9.9.336.2
OBJECT IDENTIFIER    

cgspScalars 1.3.6.1.4.1.9.9.336.1.1
OBJECT IDENTIFIER    

cgspProfile 1.3.6.1.4.1.9.9.336.1.2
OBJECT IDENTIFIER    

cgspInstance 1.3.6.1.4.1.9.9.336.1.3
OBJECT IDENTIFIER    

cgspPointCode 1.3.6.1.4.1.9.9.336.1.4
OBJECT IDENTIFIER    

cgspLinkset 1.3.6.1.4.1.9.9.336.1.5
OBJECT IDENTIFIER    


cgspNotificationsEnable 1.3.6.1.4.1.9.9.336.1.7
OBJECT IDENTIFIER    

cgspNotificationsInfo 1.3.6.1.4.1.9.9.336.1.8
OBJECT IDENTIFIER    

cgspCLLICode 1.3.6.1.4.1.9.9.336.1.1.1
Common-Language Location Identification Codes (CLLI Codes). This object identifies the physical location of this device and can provide additional informaton on the device type.
Status: current Access: read-write
OBJECT-TYPE    
  CItpTcCLLI  

cgspUtilSampleInterval 1.3.6.1.4.1.9.9.336.1.1.2
This object specifies the time interval used to monitor the utilization of SS7 links. This object in combination with cgspUtilThreshold, cgspLinkPlanCapacitySent and cgspLinkPlanCapacityRcvd will be used to calculate utilization of SS7 links. Changes to the polling interval will take effect after the completion of the current sample interval.
Status: current Access: read-write
OBJECT-TYPE    
  CgspSampleInterval  

cgspUtilThreshold 1.3.6.1.4.1.9.9.336.1.1.3
This object specifies the threshold of usage for all SS7 links in SP. This object is used to determine when to generate the ciscoGspLinkRcvdUtilChange or ciscoGspLinkSentUtilChange notifications. A value of zero indicates that no default threshold is specified. Therefore, only links with non-zero values for cgspLinkUtilThresholdRcvd or cgspLinkUtilThresholdSent will generate notifications based on link utilization. Changes to the utilization threshold will take effect at the end of the current interval.
Status: current Access: read-write
OBJECT-TYPE    
  CgspPercentThreshold  

cgspUtilAbateDelta 1.3.6.1.4.1.9.9.336.1.1.4
This object allows the falling threshold to be lower than the rising threshold when calculating whether to generate the ciscoGspLinkRcvdUtilChange or ciscoGspLinkSentUtilChange notifications. This is done to prevent generating notifications for slight changes in traffic.
Status: current Access: read-write
OBJECT-TYPE    
  CgspPercentThreshold  

cgspPlanCapacityDefault 1.3.6.1.4.1.9.9.336.1.1.5
This object provides a default for value for links with a cgspLinkType='sctpIp'. For all other types of linkset this value is ignored. When a linkset based on SCTP/IP and the values for the cgspLinkPlanCapacityRcvd or cgspLinkPlanCapacitySent object are zero then this object will be used as the default. A value of zero indicates that a global default has not been specified. This object will be used in combination with cgspUtilSampleInterval, cgspUtilThreshold, cgspUtilThreshold and cgspLinkUtilThresholdRcvd to generate the ciscoGspLinkRcvdUtilChange notification.
Status: current Access: read-write
OBJECT-TYPE    
  CgspLinkCapacity  

cgspEventSequenceNumber 1.3.6.1.4.1.9.9.336.1.1.6
Each event or notification is required to provide a sequence number to be used by the NMS to determine when messages from a particular device are missing. This value will included in each SS7 notification issued by this device.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspUPUNotifWindowTime 1.3.6.1.4.1.9.9.336.1.1.7
This object specifies the time interval used to monitor the ciscoGspUPUReceived and ciscoGspUPUTransmitted notifications for specific user part and signalling point instance. The first occurrence of ciscoGspUPUReceived and ciscoGspUPUTransmitted notifications are sent and the further occurrences of notifications in this interval are suppressed. At the end of this interval, a notification is sent with total number of UPU MSUs transmitted or received during this interval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..86400  

cgspProfileTable 1.3.6.1.4.1.9.9.336.1.2.1
A table that contains the Profiles of signalling points. Entries are added to this table via cgspProfileRowStatus in accordance with the RowStatus convention.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CgspProfileTableEntry

cgspProfileTableEntry 1.3.6.1.4.1.9.9.336.1.2.1.1
A list of Profile attributes. Profiles are used to specify common configuration options for SS7 links without customizing each link. A profile is created with the specified values using this table and the cgspProfileTimerTable Table. The common values are applied to all links in a linkset by specifying the cgspLinksetProfileName on the linkset.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspProfileTableEntry  

cgspProfileName 1.3.6.1.4.1.9.9.336.1.2.1.1.1
Name of the profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspProfileName  

cgspProfileVariant 1.3.6.1.4.1.9.9.336.1.2.1.1.2
The SS7 variant used to format data specified in this profile.
Status: current Access: read-create
OBJECT-TYPE    
  CgspSS7Variant  

cgspProfileMtp2BundleTimer 1.3.6.1.4.1.9.9.336.1.2.1.1.3
Bundle timer value. This value is used to control the bundling of SS7 packets as they are transported within the device. The value of zero indicates that MTP3 packets will not be bundled for transmission as they arrival for transmission at the MTP2 layer. A non-zero value specifies the maximum delay time used to collect MTP3 packets before they are transmitted by the MTP2 layer.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..0 | 5..10000  

cgspProfileMtp2SendQueueDepth 1.3.6.1.4.1.9.9.336.1.2.1.1.4
The maximum Queue depth allowed per link for MTP2 waiting to be transmitted.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 25..32000  

cgspProfileRowStatus 1.3.6.1.4.1.9.9.336.1.2.1.1.5
The object is used by a management station to create or delete the row entry in cgspProfileTable following the RowStatus textual convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cgspProfileTimerTable 1.3.6.1.4.1.9.9.336.1.2.2
A table that contains a profile of timers used to configure SS7 links. Entries are added to this table via cgspProfileTimerRowStatus in accordance with the RowStatus convention.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CgspProfileTimerTableEntry

cgspProfileTimerTableEntry 1.3.6.1.4.1.9.9.336.1.2.2.1
A list of ProfileTimer attributes. Profiles are used to specify common timer configuration options for SS7 links without customizing each link. A profile is created with the specified values using this table and the cgspProfileTable Table. The common values are applied to all links in a linkset by specifying the cgspLinksetProfileName on the linkset.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspProfileTimerTableEntry  

cgspProfileTimerNumber 1.3.6.1.4.1.9.9.336.1.2.2.1.1
Index into table containing timer information.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspTimerNumbers  

cgspProfileTimerValue 1.3.6.1.4.1.9.9.336.1.2.2.1.2
Value of timer selected by cgspProfileTimerNumber object.
Status: current Access: read-create
OBJECT-TYPE    
  CgspTimerValue  

cgspProfileTimerRowStatus 1.3.6.1.4.1.9.9.336.1.2.2.1.3
The object is used by a management station to create or delete the row entry in cgspProfileTimerTable following the RowStatus textual convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cgspInstanceTable 1.3.6.1.4.1.9.9.336.1.3.1
A table that contains the instances of signalling points. Entries are added to this table via cgspInstRowStatus in accordance with the RowStatus convention.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CgspInstanceTableEntry

cgspInstanceTableEntry 1.3.6.1.4.1.9.9.336.1.3.1.1
A list of instance attributes.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspInstanceTableEntry  

cgspInstNetwork 1.3.6.1.4.1.9.9.336.1.3.1.1.1
The network name is used to indicate the network in which this signalling point is participating. One or more instances of signalling points can exist in the same physical device. This identifier will be used to correlate instances of signalling points by network. When multiple instance support is not enabled the network name will default to the null string. An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space.
Status: current Access: not-accessible
OBJECT-TYPE    
  CItpTcNetworkName  

cgspInstNetworkIndicator 1.3.6.1.4.1.9.9.336.1.3.1.1.2
The Network Indicator for this Signalling point instance.
Status: current Access: read-create
OBJECT-TYPE    
  CItpTcNetworkIndicator  

cgspInstVariant 1.3.6.1.4.1.9.9.336.1.3.1.1.3
The SS7 variant used to format data used by this instance.
Status: current Access: read-create
OBJECT-TYPE    
  CgspSS7Variant  

cgspInstDisplayName 1.3.6.1.4.1.9.9.336.1.3.1.1.4
A short identifier for the Signalling point. This value can be set by system administrator or defaults to the local point code formatted as an ASCII string.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..30)  

cgspInstDescription 1.3.6.1.4.1.9.9.336.1.3.1.1.5
A textual description for the Signalling point.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..254)  

cgspInstTFR 1.3.6.1.4.1.9.9.336.1.3.1.1.6
Allow transfer restricted messages. 'true' TFR are allowed. 'false' TFR are disabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cgspInstCongestionsLevels 1.3.6.1.4.1.9.9.336.1.3.1.1.7
Allow multiple congestion levels. 'true' multiple congestion levels are allowed. 'false' multiple congestion levels are disabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cgspInstFastRestart 1.3.6.1.4.1.9.9.336.1.3.1.1.8
The support for fast restarts as follows. 'true' fast restart is enabled. 'false' fast restart is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cgspInstDistSccpUnseq 1.3.6.1.4.1.9.9.336.1.3.1.1.9
Evenly distribute Class 0 SCCP messages as follows. 'true' Evenly distribute 0 SCCP messages is enabled. 'false' Evenly distribute 0 SCCP messages is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cgspInstSummaryRoutingException 1.3.6.1.4.1.9.9.336.1.3.1.1.10
This object is used to control the usage of the summary route when both a summary route (or ANSI cluster route) and a full point-code route (within that summary) are configured. The object is used to indicate whether the summary route is to be used when the full point-code destination is inaccessible as follows. 'true' Use summary routing. 'false' Do not use summary routing.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cgspInstNumber 1.3.6.1.4.1.9.9.336.1.3.1.1.11
A unique Identifier assigned to each instance.
Status: current Access: read-only
OBJECT-TYPE    
  CItpTcInstanceNumber  

cgspInstRouteTableName 1.3.6.1.4.1.9.9.336.1.3.1.1.12
The routing table for Signalling network management messages.
Status: current Access: read-create
OBJECT-TYPE    
  CItpTcRouteTableName  

cgspInstRowStatus 1.3.6.1.4.1.9.9.336.1.3.1.1.13
The object is used by a management station to create or delete the row entry in cgspInstanceTable following the RowStatus textual convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cgspInstSccpWrrOpcShift 1.3.6.1.4.1.9.9.336.1.3.1.1.14
This object indicates the shift amount for the OPC bits in SCCP class1 WRR(Weighted round robin). The range depends on the variant as follows. The ITU range is 0-2 The ANSI range is 0-8 The CHINA range is 0-2 The JAPAN NTT range is 0-2 The JAPAN TTC range is 0-2
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..8  

cgspInstSccpWrrOption 1.3.6.1.4.1.9.9.336.1.3.1.1.15
This object indicate the options for calculate SCCP class 1 traffic loadshare under WRR
Status: current Access: read-create
OBJECT-TYPE    
  CItpTcSccpWrrOption  

cgspInstTimerTable 1.3.6.1.4.1.9.9.336.1.3.2
A table that contains the timer used to configure an instances of signalling points. Entries are added to this table via cgspInstTimerRowStatus in accordance with the RowStatus convention.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CgspInstTimerTableEntry

cgspInstTimerTableEntry 1.3.6.1.4.1.9.9.336.1.3.2.1
This table is used to configure all MTP3 timer values that apply to linksets and links. The values apply to all linkset and links defined to this signalling point(instances).
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspInstTimerTableEntry  

cgspInstTimerNumber 1.3.6.1.4.1.9.9.336.1.3.2.1.1
Index into table containing timer information.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspTimerNumbers  

cgspInstTimerValue 1.3.6.1.4.1.9.9.336.1.3.2.1.2
Value of timer selected by cgspInstTimerNumber object.
Status: current Access: read-create
OBJECT-TYPE    
  CgspTimerValue  

cgspInstTimerRowStatus 1.3.6.1.4.1.9.9.336.1.3.2.1.3
The object is used by a management station to create or delete the row entry in cgspInstTimerTable following the RowStatus textual convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cgspInstUPUTable 1.3.6.1.4.1.9.9.336.1.3.3
The Instance UPU table contains information about the number of UPU MSUs transmitted and received for the specific user part(represented by service indicator) and signalling point instance. The user part is primarily represented with the possible service indicator. This table provides the granularity of information required by Q752 table 5.6 and 5.7.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CgspInstUPUTableEntry

cgspInstUPUTableEntry 1.3.6.1.4.1.9.9.336.1.3.3.1
Each table entry represent the UPU MSU statistics for a specific user part and signalling point instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspInstUPUTableEntry  

cgspMtp3SI 1.3.6.1.4.1.9.9.336.1.3.3.1.1
The service indicator.
Status: current Access: not-accessible
OBJECT-TYPE    
  CItpTcServiceIndicator  

cgspInstSIUPUReceived 1.3.6.1.4.1.9.9.336.1.3.3.1.2
The number of UPU MSUs that were received for the associated user part(service indicator) and and signalling point instance Q752/5.7.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspInstSIUPUTransmitted 1.3.6.1.4.1.9.9.336.1.3.3.1.3
The number of UPU MSUs that were transmitted for the associated user part(service indicator) and and signalling point instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspInstUserPartDisplay 1.3.6.1.4.1.9.9.336.1.3.3.1.4
The associated instance name and user part information formatted for display.
Status: current Access: read-only
OBJECT-TYPE    
  CgspDisplayInstanceUserPart  

cgspPointCodeTable 1.3.6.1.4.1.9.9.336.1.4.1
A table that contains a list of point code defined for the Signalling point defined by this instance. Entries are added to this table via cgspPointCodeRowStatus in accordance with the RowStatus convention.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CgspPointCodeTableEntry

cgspPointCodeTableEntry 1.3.6.1.4.1.9.9.336.1.4.1.1
A list of Point codes for a signalling point defined by an instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspPointCodeTableEntry  

cgspPointCodeNi 1.3.6.1.4.1.9.9.336.1.4.1.1.1
The network Indicator for this pointcode.
Status: current Access: not-accessible
OBJECT-TYPE    
  CItpTcNetworkIndicator  

cgspPointCodeBin 1.3.6.1.4.1.9.9.336.1.4.1.1.2
The point code for this Signalling Point.
Status: current Access: not-accessible
OBJECT-TYPE    
  CItpTcPointCode  

cgspPointCodeType 1.3.6.1.4.1.9.9.336.1.4.1.1.3
The function of this point code.
Status: current Access: read-create
OBJECT-TYPE    
  CItpTcPointCodeType  

cgspPointCodeDisplay 1.3.6.1.4.1.9.9.336.1.4.1.1.4
The point code for this Signalling Point.
Status: current Access: read-only
OBJECT-TYPE    
  CItpTcDisplayPC  

cgspPointCodeRowStatus 1.3.6.1.4.1.9.9.336.1.4.1.1.5
The object is used by a management station to create or delete the row entry in cgspPointCodeTable following the RowStatus textual convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cgspLinksetTable 1.3.6.1.4.1.9.9.336.1.5.1
A table of linksets for this Signalling Point defined by this instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CgspLinksetTableEntry

cgspLinksetTableEntry 1.3.6.1.4.1.9.9.336.1.5.1.1
A list of Signalling Point linkset attributes for Signalling Point define by this instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspLinksetTableEntry  

cgspLinksetName 1.3.6.1.4.1.9.9.336.1.5.1.1.1
The name of the linkset.
Status: current Access: not-accessible
OBJECT-TYPE    
  CItpTcLinksetId  

cgspLinksetSourcePointCode 1.3.6.1.4.1.9.9.336.1.5.1.1.2
The point code to which this linkset is connected.
Status: current Access: read-create
OBJECT-TYPE    
  CItpTcPointCode  

cgspLinksetSourceDisplayPC 1.3.6.1.4.1.9.9.336.1.5.1.1.3
The point code to which this linkset is connected.
Status: current Access: read-only
OBJECT-TYPE    
  CItpTcDisplayPC  

cgspLinksetAdjacentPointCode 1.3.6.1.4.1.9.9.336.1.5.1.1.4
The point code to which this linkset is connected.
Status: current Access: read-create
OBJECT-TYPE    
  CItpTcPointCode  

cgspLinksetAdjacentDisplayPC 1.3.6.1.4.1.9.9.336.1.5.1.1.5
The point code to which this linkset is connected.
Status: current Access: read-only
OBJECT-TYPE    
  CItpTcDisplayPC  

cgspLinksetState 1.3.6.1.4.1.9.9.336.1.5.1.1.6
The list of possible linkset states. 'available' : Traffic may flow over this linkset 'shutdown' : This linkset has been forced to an unavailable state by an administrative action. 'unavailable': The linkset is currently unable to support traffic. Activation of this linkset will occur as required by protocol.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER available(1), shutdown(2), unavailable(3)  

cgspLinksetInboundAcl 1.3.6.1.4.1.9.9.336.1.5.1.1.7
Packets are filtered against this access control list before they are passed to the routing function. A value of zero indicates that no access control list is present.
Status: current Access: read-create
OBJECT-TYPE    
  CItpTcAclId  

cgspLinksetOutboundAcl 1.3.6.1.4.1.9.9.336.1.5.1.1.8
Packets are filtered against this access control list after they have passed through the routing function. A value of zero indicates that no access control list is present.
Status: current Access: read-create
OBJECT-TYPE    
  CItpTcAclId  

cgspLinksetAccountingMtp3 1.3.6.1.4.1.9.9.336.1.5.1.1.9
This indicates if accounting for this linkset is enabled. 'true' Indicates that the accounting function is enabled for this linkset and is being accumulated in cgactMtp3Table. 'false' Indicates that the accounting function is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cgspLinksetAccountingGtt 1.3.6.1.4.1.9.9.336.1.5.1.1.10
This indicates if accounting for this linkset is enabled. 'true' Indicates that the accounting function is enabled for this linkset and is being accumulated in cgactMtp3Table. 'false' Indicates that the accounting function is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  


cgspLinksetDurationInService 1.3.6.1.4.1.9.9.336.1.5.1.1.12
Time linkset was providing service related to Q752/Table 4.2.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinksetDurationOutService 1.3.6.1.4.1.9.9.336.1.5.1.1.13
Time linkset was Out-of-Service as required for Q752/Table 4.2.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinksetActPriority 1.3.6.1.4.1.9.9.336.1.5.1.1.14
Defines the activation priority for linksets. The linksets with the lowest values will be activated first. If two or more linksets share the same values they will be activated in the order they were defined.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255  

cgspLinksetDisplayName 1.3.6.1.4.1.9.9.336.1.5.1.1.15
A short identifier for each linkset. This value can be set by system administrator or defaults to the linkset name.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..30)  

cgspLinksetDescription 1.3.6.1.4.1.9.9.336.1.5.1.1.16
A textual description for the Signalling point.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..254)  

cgspLinksetRotateSlsEnable 1.3.6.1.4.1.9.9.336.1.5.1.1.17
This defines whether signalling link selector(SLS) will be rotated. This option only applies to ANSI variant and will return false for all other variants. By default SLS rotation is enable by default for ANSI linksets. ANSI specifications state that SLS rotation should not be performed on C type linksets. This object can be used to disable SLS rotation. 'true' Indicates that SLS rotation is enable for this linkset. 'false' Indicates that SLS rotation is disable for this linkset.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cgspLinksetRotateSlsShift 1.3.6.1.4.1.9.9.336.1.5.1.1.18
This value used to shift the signalling link selector(SLS) when rotation is enabled. This option only applies to ANSI variant and will return 0 all other variants.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..3  

cgspLinksetProfileName 1.3.6.1.4.1.9.9.336.1.5.1.1.19
When specified this object indicates which profile will be used to establish defaults for common configuration values like MTP2 and MTP3 timers. The null string is used to indicate that the linkset does not have a profile.
Status: current Access: read-create
OBJECT-TYPE    
  CgspProfileName  

cgspLinksetAdjacentInst 1.3.6.1.4.1.9.9.336.1.5.1.1.20
When a linkset is used to carry traffic between different instances, this object contains the network name used as an index into the cgspInstanceTable table. In all other cases the object will contain the same network name as the source signalling point.
Status: current Access: read-only
OBJECT-TYPE    
  CItpTcNetworkName  

cgspLinksetRowStatus 1.3.6.1.4.1.9.9.336.1.5.1.1.21
The object is used by a management station to create or delete the row entry in cgspLinksetTable following the RowStatus textual convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cgspLinksetTimerTable 1.3.6.1.4.1.9.9.336.1.5.2
A table that contains the timer used to configure timer values specific to a particular linkset. Entries are added to this table via cgspLinksetTimerRowStatus in accordance with the RowStatus convention.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CgspLinksetTimerTableEntry

cgspLinksetTimerTableEntry 1.3.6.1.4.1.9.9.336.1.5.2.1
This table is used to configure all MTP3 timer values that apply to linksets and links. The values apply to this linkset and links it c contains.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspLinksetTimerTableEntry  

cgspLinksetTimerNumber 1.3.6.1.4.1.9.9.336.1.5.2.1.1
Index into table containing timer information.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspTimerNumbers  

cgspLinksetTimerValue 1.3.6.1.4.1.9.9.336.1.5.2.1.2
Value of timer selected by cgspLinksetTimerNumber object.
Status: current Access: read-create
OBJECT-TYPE    
  CgspTimerValue  

cgspLinksetTimerRowStatus 1.3.6.1.4.1.9.9.336.1.5.2.1.3
The object is used by a management station to create or delete the row entry in cgspLinksetTimerTable following the RowStatus textual convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cgspLinkTable 1.3.6.1.4.1.9.9.336.1.6.1
A table of links for each Signalling Point.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CgspLinkTableEntry

cgspLinkTableEntry 1.3.6.1.4.1.9.9.336.1.6.1.1
A list of signalling point link attributes.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspLinkTableEntry  

cgspLinkSlc 1.3.6.1.4.1.9.9.336.1.6.1.1.1
The Signalling Link Code for this link.
Status: current Access: not-accessible
OBJECT-TYPE    
  CItpTcLinkSLC  

cgspLinkDescription 1.3.6.1.4.1.9.9.336.1.6.1.1.2
A textual description for this link.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..254)  

cgspLinkState 1.3.6.1.4.1.9.9.336.1.6.1.1.3
The list of possible links states. 'available' : Traffic may flow over this linkset 'failed' : Traffic management has detected a failure that prevents activating this linkset. 'shutdown' : This linkset has been forced to an unavailable state by an administrative action. 'unavailable': The linkset is currently unable to support traffic. Activation of this linkset will occur as required by protocol.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER available(1), failed(2), shutdown(3), unavailable(4)  

cgspLinkReason 1.3.6.1.4.1.9.9.336.1.6.1.1.4
This object provides additional information on the source of a link failure. This object will contain the last reason that caused the link to fail. 'unknown' : Link has failed do to an undetermined cause. 'changeOverInProgress' : Change over in progress. 'mgmtDisconnectRequest' : Management disconnect request. 'linkAlignmentLost' : Link alignment lost. 'connectionLost' : Link connection lost. 'localDisconnect' : Local Disconnect. 'remoteDisconnect' : Remote Disconnect. 'suermFailure' : Signal unit error rate monitor failure. 't1Timeout' : T1 timeout no FISU received. 't2Timeout' : T2 timeout no SIO received. 't3Timeout' : T3 timeout no SIN received. 't6Timeout' : T6 timeout excessive congestion. 't7Timeout' : T7 timeout excessive acknowledgement delay. 'provingFailure' : Link proving failure. 'protocolError-BSN' : Abnormal BSN received. 'protocolError-FIB' : Abnormal FIB received. 'protocolError-SIN' : Abnormal SIB received. 'protocolError-LSSU' : Abnormal LSSU received. 'peerNotReady' : Peer not ready. 'communicationLost' : Communication lost. 'noListenPosted' : No Listen posted. 'bufferNotAvailable' : Unable to allocate buffer. 'cardRemoved' : Link card removed. 'cardInserted' : Link card Inserted. 'falseLinkCongestion' : false link congestion. 'configDownload' : Configuration downloading. 'localInhibit' : Local request to inhibit link. 'localUninhibit' : Local request to uninhibit link. 'remoteInhibit' : Remote request to inhibit link. 'remoteUninhibit': Local request to uninhibit link. 'localBlocked' : Local Processor outage. 'localUnBlocked' : Local Processor recovery. 'remoteBlocked' : Remote Processor outage. 'remoteUnblocked': Remote Processor recovery. 'linkRestored' : Link restored. 'linkTestFailure': Signalling Link Test failure.'
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), changeOverInProgress(1), mgmtDisconnectRequest(2), linkAlignmentLost(3), connectionLost(4), localDisconnect(5), remoteDisconnect(6), suermFailure(7), t1Timeout(8), t2Timeout(9), t3Timeout(10), t6Timeout(11), t7Timeout(12), provingFailure(13), protocolErrorBsn(14), protocolErrorFib(15), protocolErrorSin(16), protocolErrorLssu(17), peerNotReady(18), communicationLost(19), noListenPosted(20), bufferNotAvailable(21), cardRemoved(22), cardInserted(23), falseLinkCongestion(24), configDownload(25), localInhibit(26), localUninhibit(27), remoteInhibit(28), remoteUninhibit(29), localBlocked(30), localUnBlocked(31), remoteBlocked(32), remoteUnblocked(33), linkRestored(34), linkTestFailure(35)  

cgspLinkType 1.3.6.1.4.1.9.9.336.1.6.1.1.5
The link type.
Status: current Access: read-create
OBJECT-TYPE    
  CItpTcLinkType  

cgspLinkifIndex 1.3.6.1.4.1.9.9.336.1.6.1.1.6
If the link type specified by cgspLinkType is serial or high speed Link, this is the ifIndex specified in IF-MIB, otherwise no significance is to be placed on this value.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

cgspLinkSctpAssociation 1.3.6.1.4.1.9.9.336.1.6.1.1.7
Association Identifiers can be greater than 65,535. This object has been replaced by cgspLinkSctpAssociationId.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

cgspLinkXmitQueueDepth 1.3.6.1.4.1.9.9.336.1.6.1.1.8
Number of packets waiting to be sent over this link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cgspLinkXmitQueueDepthHigh 1.3.6.1.4.1.9.9.336.1.6.1.1.9
This is the maximum number of packets waiting to be sent over this link since the last time this value was reset as indicated by cgspLinkXmitQueueDepthHighRT. Resetting this object is achieved by setting this object to 0. Attempting to set this object to any other value will result in a wrongValue (SNMPv2c, SNMPv3) or badValue (SNMPv1).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cgspLinkXmitQueueDepthHighRT 1.3.6.1.4.1.9.9.336.1.6.1.1.10
This indicates when cgspLinkXmitQueueDepthHigh was last set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cgspLinkCongestionState 1.3.6.1.4.1.9.9.336.1.6.1.1.11
The Signalling link congestion status of this link. 0 is the least congestion level, 3 is the highest congestion level.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..3  

cgspLinkCongestionAbate1 1.3.6.1.4.1.9.9.336.1.6.1.1.12
Threshold used to abate congestion level 1.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cgspLinkCongestionAbate2 1.3.6.1.4.1.9.9.336.1.6.1.1.13
Threshold used to abate congestion level 2.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cgspLinkCongestionAbate3 1.3.6.1.4.1.9.9.336.1.6.1.1.14
Threshold used to abate congestion level 3.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cgspLinkCongestionOnset1 1.3.6.1.4.1.9.9.336.1.6.1.1.15
Threshold used to mark onset of congestion level 1.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cgspLinkCongestionOnset2 1.3.6.1.4.1.9.9.336.1.6.1.1.16
Threshold used to mark onset of congestion level 2.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cgspLinkCongestionOnset3 1.3.6.1.4.1.9.9.336.1.6.1.1.17
Threshold used to mark onset of congestion level 3.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cgspLinkSigLinkTest 1.3.6.1.4.1.9.9.336.1.6.1.1.18
Indicated if Signalling link test is enabled on this link. true : Signalling link test is enabled. false : Signalling link test not enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cgspLinkQ752T1E1 1.3.6.1.4.1.9.9.336.1.6.1.1.19
Duration of link in the In-Service state Q752/1.1.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T1E2 1.3.6.1.4.1.9.9.336.1.6.1.1.20
Count of Signalling Link failures - All reasons Q752/1.2.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T1E3 1.3.6.1.4.1.9.9.336.1.6.1.1.21
Count of Signalling Link failures - Abnormal FIBR/BSNR Q752/1.3
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T1E5 1.3.6.1.4.1.9.9.336.1.6.1.1.22
Count of Signalling Link failures - Excessive error rate Q752/1.5.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T1E7 1.3.6.1.4.1.9.9.336.1.6.1.1.23
Count of alignment or proving errors Q752/1.7.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T1E8 1.3.6.1.4.1.9.9.336.1.6.1.1.24
Count of signal units received in error Q752/1.8.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T1E9 1.3.6.1.4.1.9.9.336.1.6.1.1.25
Count of negative acknowledgements received Q752/1.9.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T1E10 1.3.6.1.4.1.9.9.336.1.6.1.1.26
Count of 'local automatic changeover' events Q752/1.10.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T1E11 1.3.6.1.4.1.9.9.336.1.6.1.1.27
Count of 'local automatic changeback' events Q752/1.11.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T2E1 1.3.6.1.4.1.9.9.336.1.6.1.1.28
Duration of Signalling Link unavailable(for any reason) Q752/2.1.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T2E5 1.3.6.1.4.1.9.9.336.1.6.1.1.29
Duration of Signalling Link unavailable due to local management actions Q752/2.5.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T2E6 1.3.6.1.4.1.9.9.336.1.6.1.1.30
Duration of Signalling Link unavailable due to remote management actions Q752/2.6.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T2E7 1.3.6.1.4.1.9.9.336.1.6.1.1.31
Duration of Signalling Link unavailable due to link failure Q752/2.7.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T2E9 1.3.6.1.4.1.9.9.336.1.6.1.1.32
Duration of Signalling Link unavailable due to remote processor outage Q752/2.9.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T2E10 1.3.6.1.4.1.9.9.336.1.6.1.1.33
Count of 'remote processor outage' events Q752/2.10 and Q752/2.11. The standard only requires that events are issued. The entries have been combined into a single entry to track all occurrences of these event types.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T2E15 1.3.6.1.4.1.9.9.336.1.6.1.1.34
Count of Status Indicator Busy received Q752/2.15.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T2E16 1.3.6.1.4.1.9.9.336.1.6.1.1.35
Count of local inhibition Q752/2.16 and Q752/2.17. The standard only requires that events are issued. The entries have been combined into a single entry to track all occurrences of these event types.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T2E18 1.3.6.1.4.1.9.9.336.1.6.1.1.36
Count of remote inhibition Q752/2.18 and Q752/2.19. The standard only requires that events are issued. The entries have been combined into a single entry to track all occurrences of these event types.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E1 1.3.6.1.4.1.9.9.336.1.6.1.1.37
The number of MTP3 bytes sent by this link. This measurement is specified in Q752/3.1
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E2Bytes 1.3.6.1.4.1.9.9.336.1.6.1.1.38
The number of MTP3 bytes retransmitted on this link. This measurement is specified in Q752/3.2
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E2Packets 1.3.6.1.4.1.9.9.336.1.6.1.1.39
The number of MTP3 packets retransmitted on this link. This measurement is specified in Q752/3.2
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E3 1.3.6.1.4.1.9.9.336.1.6.1.1.40
The number of MTP3 packets sent by this link. This measurement is specified in Q752/3.3.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E4 1.3.6.1.4.1.9.9.336.1.6.1.1.41
The number of MTP3 bytes received by this link. This measurement is specified in Q752/3.4
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E5 1.3.6.1.4.1.9.9.336.1.6.1.1.42
The number of MTP3 packets received by this link. This measurement is specified in Q752/3.5
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E6 1.3.6.1.4.1.9.9.336.1.6.1.1.43
The number times this Signalling link was marked congested. This measurement is specified in Q752/3.6
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E7 1.3.6.1.4.1.9.9.336.1.6.1.1.44
Cumulative duration of Signalling link congestion Q752/3.7.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E10L1 1.3.6.1.4.1.9.9.336.1.6.1.1.45
The number of packets(MSUs) discarded due to Signalling link level 1 congestion Q752/3.10
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E10L2 1.3.6.1.4.1.9.9.336.1.6.1.1.46
The number of packets(MSUs) discard due to Signalling link level 2 congestion Q752/3.10
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E10L3 1.3.6.1.4.1.9.9.336.1.6.1.1.47
The number of packets(MSUs) discard due to Signalling link level 3 congestion Q752/3.10
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E11L1 1.3.6.1.4.1.9.9.336.1.6.1.1.48
The number times this Signalling link entered congestion level 1 and packets were discarded. This measurement is specified in Q752/3.11
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E11L2 1.3.6.1.4.1.9.9.336.1.6.1.1.49
The number times this Signalling link entered congestion level 2 and packets were discarded. This measurement is specified in Q752/3.11
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T3E11L3 1.3.6.1.4.1.9.9.336.1.6.1.1.50
The number times this Signalling link entered congestion level 3 and packets were discarded. This measurement is specified in Q752/3.11
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkLocalPeerPort 1.3.6.1.4.1.9.9.336.1.6.1.1.51
When cgspLinkType is set to 'sctpIp' then this object contains the local port number used to create the association supporting this link. This object can be used to obtain information from the cgsp2LocalPeerTable and cgsp2LpIpAddrTable Tables in the CISCO-ITP-GSP2-MIB.my MIB.
Status: current Access: read-create
OBJECT-TYPE    
  InetPortNumber  

cgspLinkRemotePeerPort 1.3.6.1.4.1.9.9.336.1.6.1.1.52
When cgspLinkType is set to 'sctpIp' then this object contains the remote port number used to create the association supporting this link. When cgspLinkType is not set to 'sctpIp' then no significance is to be placed on this value.
Status: current Access: read-create
OBJECT-TYPE    
  InetPortNumber  

cgspLinkQosClass 1.3.6.1.4.1.9.9.336.1.6.1.1.53
When cgspLinkType is set to 'sctpIp' then this object contains the quality of service class to be assigned to packets sent on this association. When cgspLinkType is not set to 'sctpIp' then no significance is to be placed on this value.
Status: current Access: read-create
OBJECT-TYPE    
  CItpTcQos  

cgspLinkDisplayName 1.3.6.1.4.1.9.9.336.1.6.1.1.54
A short identifier for each link linkset. This value can be set by system administrator or defaults to the linkset name and SLC formatted as an ASCII string.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..30)  

cgspLinkDroppedPkts 1.3.6.1.4.1.9.9.336.1.6.1.1.55
The number of packets that were dropped by this link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkTransmittedLSSUs 1.3.6.1.4.1.9.9.336.1.6.1.1.56
The number of Link Status Signal Units sent on this link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkReceivedLSSUs 1.3.6.1.4.1.9.9.336.1.6.1.1.57
The number of Link Status Signal Units received on this link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkProtocolDetails 1.3.6.1.4.1.9.9.336.1.6.1.1.58
This object provide details on the protocol states for this link as follows. Changeback control(TCBC) 'tcbcBuffering': Changeback control is buffering data on this link. Changeover control(TCOC) 'tcocBuffering': Changeover control is buffering data on this link Link availability control(TLAC) 'tlacAdjacentSpRestarting': Adjacent Signalling point is restarting. 'tlacEmergencyCoInProgress': Emergency changeover is in progress on this link. 'tlacChangebackInProgress': Changeback is in progress on this link. 'tlacChangeoverInProgress': Changeover is in progress on this link. 'tlacChangeoverFailed': The last changeover operation failed on this link. 'tlacInhibitRetry': Inhibit command will be retried. 'tlacManagementRequest': Management request in progress for this link. 'tlacSpRestarting': Signalling point is in the process of a restart. 'tlacLocalInhibit': Link has been inhibited by a local management operation. 'tlacRemoteInhibit': Link has been inhibited by a remote management operation. 'tlacLocalBlocked': Link is blocked because of a local processor outage. 'tlacRemoteBlocked': Link is blocked because of a remote processor outage. Signalling routing control(TSRC) 'tsrcChangeOverComplete': Changeove request is complete. 'tsrcAdjacentSpRestart': Adjacent Signalling Point is restarting.
Status: current Access: read-only
OBJECT-TYPE    
  BITS tcbcBuffering(0), tcocBuffering(1), tlacAdjacentSpRestarting(2), tlacEmergencyCoInProgress(3), tlacChangebackInProgress(4), tlacChangeoverInProgress(5), tlacChangeoverFailed(6), tlacInhibitRetry(7), tlacManagementRequest(8), tlacSpRestarting(9), tsrcChangeOverComplete(10), tsrcAdjacentSpRestart(11), tlacLocalInhibit(12), tlacRemoteInhibit(13), tlacLocalBlocked(14), tlacRemoteBlocked(15)  

cgspLinkLsacState 1.3.6.1.4.1.9.9.336.1.6.1.1.59
Signalling link activity control state: 'undefined' - link is an undefined state 'inactive' - A Signalling link that is not in operation. 'active' - A Signalling link that is in operation. 'activatingRestoring' - A Signalling that is not operational and is being activated or restored. 'failed' - A Signalling link which is available (not blocked) is marked by level 3 as failed when a changeover order is received. 'actT17wait' - Link activation has failed. Link is placed into this state to wait for timer T17 to expire in order to avoid the oscillation of initial alignment failure and link restart. 'actAnsiWaitDeloaded - Waiting for change back acknowledgement (second attempt). 'actItuWaitStmReady' Wait for Signalling Traffic Management ready event.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER undefined(1), inactive(2), active(3), activatingRestoring(4), failed(5), actT17wait(6), actAnsiWaitDeloaded(7), actItuWaitStmReady(8)  

cgspLinkTsrcState 1.3.6.1.4.1.9.9.336.1.6.1.1.60
Signalling traffic management routing control state: 'undefined' - link is an undefined state 'idle' - traffic management is idle 'wait5' - traffic management is active and in the sending status phase
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER undefined(1), idle(2), wait5(3)  

cgspLinkTcocState 1.3.6.1.4.1.9.9.336.1.6.1.1.61
Changeover control State: 'undefined' - Link is an undefined state. 'idle' - Link is available and idle. 'wait2' - Wait for MTP2 to initialize link. 'waitForAck' - Waiting for changeover acknowledgement. 'retrieving' - Packets are being retrieved from link. 'wait5' - Wait state when transitioning from idle state. 'wait7' - Delay to avoid message mis-sequencing on changeover 'wait8' - Wait state prior to processing changeover order or emergency changeover order events.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER undefined(1), idle(2), wait2(3), waitForAck(4), retrieving(5), wait5(6), wait7(7), wait8(8)  

cgspLinkTcocLocalBSNT 1.3.6.1.4.1.9.9.336.1.6.1.1.62
The local backward sequence number to be transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  CgspSequenceNumber  

cgspLinkTcocRemoteBSNT 1.3.6.1.4.1.9.9.336.1.6.1.1.63
The remote backward sequence number to be transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  CgspSequenceNumber  

cgspLinkTcbcState 1.3.6.1.4.1.9.9.336.1.6.1.1.64
Changeback control State: 'undefined' - link is an undefined state. 'idle' - Link is available and idle. 'firstAttempt' - First attempt at changeback. 'secondAttempt' - Second attempt at changeback 'timeControlledDiversion' - Changeback using time controlled Diversion.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER undefined(1), idle(2), firstAttempt(3), secondAttempt(4), timeControlledDiversion(5)  

cgspLinkReceivedSIBs 1.3.6.1.4.1.9.9.336.1.6.1.1.65
The number of status indicator 'busy' link status signal units received on this link. The SIB indicates that level two is congested at the transmitting Signalling point.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkTransmittedSIBs 1.3.6.1.4.1.9.9.336.1.6.1.1.66
The number of status indicator 'busy' link status signal units transmitted on this link. The SIB indicates that level two is congested at the transmitting Signalling point.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkMtp2T01Counts 1.3.6.1.4.1.9.9.336.1.6.1.1.67
The number of times the alignment ready timer has expired on this link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkMtp2T02Counts 1.3.6.1.4.1.9.9.336.1.6.1.1.68
The number of times the not alignment ready timer has expired on this link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkMtp2T03Counts 1.3.6.1.4.1.9.9.336.1.6.1.1.69
The number of times the aligned timer has expired on this link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkMtp2T04Counts 1.3.6.1.4.1.9.9.336.1.6.1.1.70
The number of times the proving period timer has expired on this link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkMtp2T05Counts 1.3.6.1.4.1.9.9.336.1.6.1.1.71
The number of times the sending status indicator busy timer has expired on this link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkMtp2T06Counts 1.3.6.1.4.1.9.9.336.1.6.1.1.72
The number of times the remote congestion timer has expired on this link(Q752/1.6).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkMtp2T07Counts 1.3.6.1.4.1.9.9.336.1.6.1.1.73
The number of times the excessive delay of acknowledgement timer has expired on this link(Q752/1.4).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkOMAERMCounts 1.3.6.1.4.1.9.9.336.1.6.1.1.74
The number of times the Alignment Error Rate Monitor procedure was started on this link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkOMAERMFailCounts 1.3.6.1.4.1.9.9.336.1.6.1.1.75
The number of times the Alignment Error Rate Monitor procedure failed on this link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkOMSURMCounts 1.3.6.1.4.1.9.9.336.1.6.1.1.76
The number of times the Signal Unit Error Rate Monitor procedure was started on this link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkOMSURMFailCounts 1.3.6.1.4.1.9.9.336.1.6.1.1.77
The number of times the Signal Unit Error Rate Monitor procedure failed on this link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkPlanCapacityRcvd 1.3.6.1.4.1.9.9.336.1.6.1.1.78
An estimate of the number of bits per second that is expected to be received from this link. This object will be used in combination with cgspUtilSampleInterval, cgspUtilThreshold, cgspUtilThreshold and cgspLinkUtilThresholdRcvd to generate the ciscoGspLinkRcvdUtilChange notification.
Status: current Access: read-create
OBJECT-TYPE    
  CgspLinkCapacity  

cgspLinkUtilThresholdRcvd 1.3.6.1.4.1.9.9.336.1.6.1.1.79
This object specifies the threshold used to to generate the ciscoGspLinkRcvdUtilChange notification. The value of zero indicates the threshold has not been defined at the link level and the value from the cgspLinksetUtilThresholdRcvd or cgspUtilThreshold objects will be used to generate the ciscoGspLinkRcvdUtilChange notification.
Status: current Access: read-create
OBJECT-TYPE    
  CgspPercentThreshold  

cgspLinkUtilizationRcvd 1.3.6.1.4.1.9.9.336.1.6.1.1.80
An estimate of the utilization of this link for traffic received on this link in the prior time period defined by the cgspUtilSampleInterval object.
Status: current Access: read-only
OBJECT-TYPE    
  CgspLinkUtilization  

cgspLinkUtilStateRcvd 1.3.6.1.4.1.9.9.336.1.6.1.1.81
Link Utilization State for inbound traffic.
Status: current Access: read-only
OBJECT-TYPE    
  CgspLinkUtilizationState  

cgspLinkL2BytesRcvd 1.3.6.1.4.1.9.9.336.1.6.1.1.82
A count of the bytes received on the link including the additional bytes required by underlying protocols. This provides a transport independent mechanism for collection information on link utilization.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkPlanCapacitySent 1.3.6.1.4.1.9.9.336.1.6.1.1.83
An estimate of the number of bits per second that is expected to be sent on this link. This object will be used in combination with cgspUtilSampleInterval, cgspUtilThreshold and cgspLinkUtilThresholdRcvd to generate the ciscoGspLinkSentUtilChange notification.
Status: current Access: read-create
OBJECT-TYPE    
  CgspLinkCapacity  

cgspLinkUtilThresholdSent 1.3.6.1.4.1.9.9.336.1.6.1.1.84
This object specifies the threshold used to generate the ciscoGspLinkRcvdUtilChange notification. The value of zero indicates the threshold has not been defined at the link level and the value from the cgspLinksetUtilThresholdRcvd or cgspUtilThreshold objects will be used to generate the ciscoGspLinkRcvdUtilChange notification.
Status: current Access: read-create
OBJECT-TYPE    
  CgspPercentThreshold  

cgspLinkUtilizationSent 1.3.6.1.4.1.9.9.336.1.6.1.1.85
An estimate of the utilization of this link for traffic sent on this link in the prior time period defined by the cgspUtilSampleInterval object.
Status: current Access: read-only
OBJECT-TYPE    
  CgspLinkUtilization  

cgspLinkUtilStateSent 1.3.6.1.4.1.9.9.336.1.6.1.1.86
Link Utilization State for out bound traffic.
Status: current Access: read-only
OBJECT-TYPE    
  CgspLinkUtilizationState  

cgspLinkL2BytesSent 1.3.6.1.4.1.9.9.336.1.6.1.1.87
A count of the bytes sent on the link including the additional bytes required by underlying protocols. This provides a transport independent mechanism for collection information on link utilization.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkTestResult 1.3.6.1.4.1.9.9.336.1.6.1.1.88
This object provides information on result from signalling link test received on this link.
Status: current Access: read-only
OBJECT-TYPE    
  CgspLinkTestResults  

cgspLinkRowStatus 1.3.6.1.4.1.9.9.336.1.6.1.1.89
The object is used by a management station to create or delete the row entry in cgspLinkTable following the RowStatus textual convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cgspLinkSctpAssociationId 1.3.6.1.4.1.9.9.336.1.6.1.1.90
If the link type specified by cgspLinkType is 'sctpIp', this is the association identifier defined in the Stream Control Transmission Protocol(SCTP) MIB. Where value greater than zero indicates a valid association. The zero value indicates an association does not exist for this link. This value will always be set to zero one when cgspLinkType is not equal to the 'sctpIp' value. This object replaces cgspLinkSctpAssociation and allows association identifiers to be larger than 65,535.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cgspLinkQ752T1E12 1.3.6.1.4.1.9.9.336.1.6.1.1.91
Count of 'Signalling Link Restoration' events Q752/1.12.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T1E12Errors 1.3.6.1.4.1.9.9.336.1.6.1.1.92
Count of 'Signalling Link Restoration' error events related to Q752/1.12. i.e., the number of times the link restoration was attempted and the link was not recovered.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T2E11 1.3.6.1.4.1.9.9.336.1.6.1.1.93
Count of 'remote processor recovery' events Q752/2.11. The standard only requires that events are issued.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T2E17 1.3.6.1.4.1.9.9.336.1.6.1.1.94
Count of local uninhibition Q752/2.17. The standard only requires that events are issued.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkQ752T2E19 1.3.6.1.4.1.9.9.336.1.6.1.1.95
Count of remote uninhibition Q752/2.19. The standard only requires that events are issued.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cgspLinkRxCongestionState 1.3.6.1.4.1.9.9.336.1.6.1.1.96
The Signalling link Received Side congestion status of this link. 0 abate, 1 onset is the received side congestion level
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..1  

cgspLinkTimerTable 1.3.6.1.4.1.9.9.336.1.6.2
A table that contains the timer used to configure timer values specific to a particular Link. Entries are added to this table via cgspLinkTimerRowStatus in accordance with the RowStatus convention.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CgspLinkTimerTableEntry

cgspLinkTimerTableEntry 1.3.6.1.4.1.9.9.336.1.6.2.1
This table is used to configure all MTP3 timer values that apply to links. The values apply to a particular link.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspLinkTimerTableEntry  

cgspLinkTimerNumber 1.3.6.1.4.1.9.9.336.1.6.2.1.1
Index into table containing timer information.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspTimerNumbers  

cgspLinkTimerValue 1.3.6.1.4.1.9.9.336.1.6.2.1.2
Value of timer selected by cgspLinkTimerNumber object.
Status: current Access: read-create
OBJECT-TYPE    
  CgspTimerValue  

cgspLinkTimerRowStatus 1.3.6.1.4.1.9.9.336.1.6.2.1.3
The object is used by a management station to create or delete the row entry in cgspLinkTimerTable following the RowStatus textual convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cgspLinkRemoteIpAddrTable 1.3.6.1.4.1.9.9.336.1.6.3
A table that contains the remote IP addresses used to configure a particular Link. Entries are added to this table via cgspLinkRemoteIpAddrRowStatus in accordance with the RowStatus convention.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CgspLinkRemoteIpAddrTableEntry

cgspLinkRemoteIpAddrTableEntry 1.3.6.1.4.1.9.9.336.1.6.3.1
A list of remote IP addresses per Link.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspLinkRemoteIpAddrTableEntry  

cgspLinkRemoteIpAddrNumber 1.3.6.1.4.1.9.9.336.1.6.3.1.1
This object specifies the index for the IP addresses in the remote IP Address table
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..65535  

cgspLinkRemoteIpAddrType 1.3.6.1.4.1.9.9.336.1.6.3.1.2
This object contains the type of the local IP address used to create an association.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

cgspLinkRemoteIpAddress 1.3.6.1.4.1.9.9.336.1.6.3.1.3
This object contains the remote IP address used to create the association with the partner of this association.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

cgspLinkRemoteIpAddrRowStatus 1.3.6.1.4.1.9.9.336.1.6.3.1.4
The object is used by a management station to create or delete the row entry in cgspLinkRemoteIpAddrTable following the RowStatus textual convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cgspLinkUtilTable 1.3.6.1.4.1.9.9.336.1.6.4
A table that contains a history of the cgspLinkUtilizationRcvd and cgspLinkUtilizationRcvd objects. In order to properly manage network capacity it is necessary to collect utilization information during short interval. These intervals are less than 5 minutes and can be as low as 1 minute. The number of links supported by a signalling point prevent polling each signalling point to collect information. This table is provided to allow an NMS to collect the information during a normal poll cycle.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CgspLinkUtilTableEntry

cgspLinkUtilTableEntry 1.3.6.1.4.1.9.9.336.1.6.4.1
A collection of entries used to store a history link utilization values. Values from cgspLinkUtilizationRcvd and cgspLinkUtilizationSent objects are saved in cgspLinkUtilRcvd and cgspLinkUtilSent.
Status: current Access: not-accessible
OBJECT-TYPE    
  CgspLinkUtilTableEntry  

cgspLinkUtilIndex 1.3.6.1.4.1.9.9.336.1.6.4.1.1
Index used to access historical link utilization information. Entry one corresponds to the most recent utilization window for the length of time specified by the cgspUtilSampleInterval object. Example of utilization history using default values. Current Time: 10:42 am Sample Interval: 300 seconds cgspLinkUtilIndex [1] Window from 10:36-10:41 [2] Window from 10:31-10:36 [3] Window from 10:26-10:31 . . [n] The index ranges from one to a maximum of sixty entries. The actual number of entries will depend on the implementation and available resources.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..60  

cgspLinkUtilRcvd 1.3.6.1.4.1.9.9.336.1.6.4.1.2
An estimate of the utilization of this link for traffic received on this link in the time period defined by the cgspUtilSampleInterval object.
Status: current Access: read-only
OBJECT-TYPE    
  CgspLinkUtilization  

cgspLinkUtilSent 1.3.6.1.4.1.9.9.336.1.6.4.1.3
An estimate of the utilization of this link for traffic transmitted on this link in the time period defined by the cgspUtilSampleInterval object.
Status: current Access: read-only
OBJECT-TYPE    
  CgspLinkUtilization  

cgspLinkUtilEndTimestamp 1.3.6.1.4.1.9.9.336.1.6.4.1.4
This timestamp indicates when time period ended for this sample.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cgspLsStateChangeNotifEnabled 1.3.6.1.4.1.9.9.336.1.7.1
The signalling point linkset notification truth value. 'true' Indicates that ciscoGspLinksetStateChange notification is to be generated when the state changes. That is, the notification generation is enabled. 'false' Indicates that ciscoGspLinksetStateChange notification generation is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cgspLnkStateChangeNotifEnabled 1.3.6.1.4.1.9.9.336.1.7.2
The signalling point link notification truth value. 'true' Indicates that ciscoGspLinkStateChange notification is to be generated when the state changes. That is, the notification generation is enabled. 'false' Indicates that ciscoGspLinkStateChange notification generation is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cgspCongestionNotifEnabled 1.3.6.1.4.1.9.9.336.1.7.3
The signalling point congestion notification truth value. 'true' Indicates that ciscoGspCongestionChange and ciscoGspRxCongestionChange notification is to be generated when the state changes. That is, the notification generation is enabled. 'false' Indicates that ciscoGspCongestionChange and ciscoGspRxCongestionChange notification generation is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cgspLinkUtilNotifEnabled 1.3.6.1.4.1.9.9.336.1.7.4
The signalling point link utilization notification truth value. 'true' Indicates that the notification of link utilization has been enabled. That is, the notification generation is enabled. 'false' Indicates that the notification link utilization has been disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cgspIsolationNotifEnabled 1.3.6.1.4.1.9.9.336.1.7.5
The isolation notification truth value. 'true' Indicates that the notification of isolation has been enabled. That is, the notification generation is enabled. 'false' Indicates that the notification of isolation has been disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cgspUPUNotifEnabled 1.3.6.1.4.1.9.9.336.1.7.6
A control to enable or disable both ciscoGspUPUReceived and ciscoGspUPUTransmitted notifications as follows: 'true' Indicates that the ciscoGspUPUReceived and ciscoGspUPUTransmitted notification generation is enabled. 'false' Indicates that ciscoGspUPUReceived and ciscoGspUPUTransmitted notification generation is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cgspUPUIntervalDuration 1.3.6.1.4.1.9.9.336.1.8.1
Duration elapsed since the start of the cgspUPUNotifWindowTime interval. This duration value can range from 0 upto cgspUPUNotifWindowTime. For the notifications generated at the end of the interval, this value will be equal to cgspUPUNotifWindowTime.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

cgspIntervalUPUs 1.3.6.1.4.1.9.9.336.1.8.2
Number of UPU MSUs received or transmitted during this specific cgspUPUIntervalDuration interval.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

ciscoGspLinksetStateChange 1.3.6.1.4.1.9.9.336.0.1
The notification generated when a linkset changes to a new state. The value of cgspLinksetState indicates the new state.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoGspLinkStateChange 1.3.6.1.4.1.9.9.336.0.2
The notification generated when a link changes to a new state. The value of cgspLinkState indicates the new state.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoGspCongestionChange 1.3.6.1.4.1.9.9.336.0.3
The notification generated when a link changes to a new congestion level as specified by cgspLinkCongestionState object for Transmission Side congestion.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoGspLinkRcvdUtilChange 1.3.6.1.4.1.9.9.336.0.4
The notification provide is generated when the cgspLinkUtilStateRcvd changes states.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoGspLinkSentUtilChange 1.3.6.1.4.1.9.9.336.0.5
The notification provide is generated when the cgspLinkUtilStateSent changes states.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoGspIsolation 1.3.6.1.4.1.9.9.336.0.6
This notification indicates the instance specified by cgspInstDisplayName and cgspInstDescription has become isolated. All linkset used to connect MTP3 node (instance) are unavailable. Isolation is ended when any linkset supported by this instance reaches the active state.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoGspUPUReceived 1.3.6.1.4.1.9.9.336.0.8
The notification is generated when an UPU MSU is received from a remote signalling point, for a specific instance and user part for the first time in the configured cgspUPUNotifWindowTime. For cases when there is a non-zero number of UPU MSUs received, this notification will be sent at the end of the cgspUPUNotifWindowTime interval, with cgspIntervalUPUs indicating the total count of UPU MSUs received for that specific instance and user part during the entire cgspUPUNotifWindowTime interval Q752/5.6.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoGspUPUTransmitted 1.3.6.1.4.1.9.9.336.0.9
The notification is generated when an UPU MSU is transmitted to a remote signalling point, for a specific instance and user part for the first time in the configured cgspUPUNotifWindowTime. For cases when there is a non-zero number of UPU MSUs received, this notification will be sent at the end of the cgspUPUNotifWindowTime interval, with cgspIntervalUPUs indicating the total count of UPU MSUs transmitted for that specific instance and user part during the entire cgspUPUNotifWindowTime interval Q752/5.7.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoGspRxCongestionChange 1.3.6.1.4.1.9.9.336.0.10
The notification generated when a link changes to a new congestion level as specified by cgspLinkRxCongestionstate object for Received side congestion
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoGspMIBCompliances 1.3.6.1.4.1.9.9.336.2.1
OBJECT IDENTIFIER    

ciscoGspMIBGroups 1.3.6.1.4.1.9.9.336.2.2
OBJECT IDENTIFIER    

ciscoGspMIBCompliance 1.3.6.1.4.1.9.9.336.2.1.1
The compliance statement for entities which implement the CISCO-ITP-GSP-MIB
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoGspMIBComplianceRev1 1.3.6.1.4.1.9.9.336.2.1.2
The compliance statement for entities which implement the CISCO-ITP-GSP-MIB
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoGspMIBComplianceRev2 1.3.6.1.4.1.9.9.336.2.1.3
The compliance statement for entities which implement the CISCO-ITP-GSP-MIB
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoGspMIBComplianceRev3 1.3.6.1.4.1.9.9.336.2.1.4
The compliance statement for entities which implement the CISCO-ITP-GSP-MIB
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoGspMIBComplianceRev4 1.3.6.1.4.1.9.9.336.2.1.5
The compliance statement for entities which implement the CISCO-ITP-GSP-MIB
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoGspMIBComplianceRev5 1.3.6.1.4.1.9.9.336.2.1.6
The compliance statement for entities which implement the CISCO-ITP-GSP-MIB
Status: current Access: read-only
MODULE-COMPLIANCE    

ciscoGspScalarsGroup 1.3.6.1.4.1.9.9.336.2.2.1
Scalars Group for Gateway Signalling Point.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspProfileGroup 1.3.6.1.4.1.9.9.336.2.2.2
Profile Group for Gateway Signalling Point.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspInstanceGroup 1.3.6.1.4.1.9.9.336.2.2.3
Instance of Signalling Point.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspInstTimerGroup 1.3.6.1.4.1.9.9.336.2.2.4
Timers defined for each Instance of Signalling Point.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspPointCodeGroup 1.3.6.1.4.1.9.9.336.2.2.5
Pointcode defined for each Instance of Signalling Point.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspLinksetGroup 1.3.6.1.4.1.9.9.336.2.2.6
linkset objects .
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspLinksetTimerGroup 1.3.6.1.4.1.9.9.336.2.2.7
Timers defined for each Linkset.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspLinkGroup 1.3.6.1.4.1.9.9.336.2.2.8
SP link objects.
Status: deprecated Access: read-only
OBJECT-GROUP    

ciscoGspLinkTimerGroup 1.3.6.1.4.1.9.9.336.2.2.9
Timers defined for each Link.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspLinkRemoteIpGroup 1.3.6.1.4.1.9.9.336.2.2.10
Remote IP addresses for each Link.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspLinkUtilGroup 1.3.6.1.4.1.9.9.336.2.2.11
Utilization history for each Link.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspNotificationsEnableGroup 1.3.6.1.4.1.9.9.336.2.2.12
SP enable notification objects.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspNotificationsGroup 1.3.6.1.4.1.9.9.336.2.2.13
SP notifications.
Status: current Access: read-only
NOTIFICATION-GROUP    

ciscoGspLinkGroupRev1 1.3.6.1.4.1.9.9.336.2.2.14
SP link objects.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspNotificationsEnableGroupSup1 1.3.6.1.4.1.9.9.336.2.2.15
Isolation notification enable.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspNotificationsGroupSup1 1.3.6.1.4.1.9.9.336.2.2.16
Isolation notification.
Status: current Access: read-only
NOTIFICATION-GROUP    

ciscoGspLinkGroupSup1 1.3.6.1.4.1.9.9.336.2.2.17
Additional Link statistics.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspScalarsGroupSup1 1.3.6.1.4.1.9.9.336.2.2.18
Scalar Group supplements.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspInstUPUGroup 1.3.6.1.4.1.9.9.336.2.2.20
SS7 Destination and Service Indicator group.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspNotificationsInfoGroup 1.3.6.1.4.1.9.9.336.2.2.21
Notifications Info Group.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspNotificationsEnableGroupSup2 1.3.6.1.4.1.9.9.336.2.2.22
UPU notifications enable.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspNotificationsGroupSup2 1.3.6.1.4.1.9.9.336.2.2.23
Adjacent SP accessibility notification, UPU sent and received notifications.
Status: current Access: read-only
NOTIFICATION-GROUP    

ciscoGspInstSccpWrrGroup 1.3.6.1.4.1.9.9.336.2.2.24
SCCP GTT weighted loadshare group.
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspLinkTableEntryGroupSup1 1.3.6.1.4.1.9.9.336.2.2.25
cgspLinkRxCongestionstate object for Received side congestion
Status: current Access: read-only
OBJECT-GROUP    

ciscoGspNotificationsGroupSup3 1.3.6.1.4.1.9.9.336.2.2.26
Link Receive side congestion notication.
Status: current Access: read-only
NOTIFICATION-GROUP