CISCO-GGSN-MIB

File: CISCO-GGSN-MIB.mib (178464 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF IF-MIB
SNMPv2-TC INET-ADDRESS-MIB SNMP-FRAMEWORK-MIB
CISCO-TC CISCO-GTP-MIB CISCO-SMI

Imported symbols

MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE
Integer32 Counter32 Counter64
Unsigned32 Gauge32 MODULE-COMPLIANCE
OBJECT-GROUP NOTIFICATION-GROUP InterfaceIndexOrZero
ifIndex DisplayString TruthValue
TimeStamp RowStatus InetAddressType
InetAddress InetAddressDNS InetAddressPrefixLength
SnmpAdminString CiscoAlarmSeverity CiscoInetAddressMask
cGtpPathAddressType cGtpPathAddress cGtpPathPort
ciscoMgmt

Defined Types

CGgsnSgsnStatEntry  
SEQUENCE    
  cGgsnSgsnThruPutInterval Integer32
  cGgsnSgsnThruPutLastCollected Integer32
  cGgsnSgsnUpStreamPktCnt Gauge32
  cGgsnSgsnUpStreamByteCnt Gauge32
  cGgsnSgsnDownStreamPktCnt Gauge32
  cGgsnSgsnDownStreamByteCnt Gauge32

CGgsnHistNotifEntry  
SEQUENCE    
  cGgsnHistNotifIndex Unsigned32
  cGgsnHistNotifType INTEGER
  cGgsnHistNotifSeverity CiscoAlarmSeverity
  cGgsnHistNotifTimestamp TimeStamp
  cGgsnHistNotifGgsnIpAddrType InetAddressType
  cGgsnHistNotifGgsnIpAddr InetAddress
  cGgsnHistNotifInfo DisplayString

CGgsnIpDupProtectEntry  
SEQUENCE    
  cGgsnMsExcludeRangeStartIpType InetAddressType
  cGgsnMsExcludeRangeStartIp InetAddress
  cGgsnMsExcludeRangeEndIpType InetAddressType
  cGgsnMsExcludeRangeEndIp InetAddress
  cGgsnIpDupProtectRowStatus RowStatus
  cGgsnMsExcludeRangeStartIpv6Prefixlen InetAddressPrefixLength
  cGgsnMsExcludeRangeEndIpv6Prefixlen InetAddressPrefixLength

CGgsnDefaultAggregEntry  
SEQUENCE    
  cGgsnDefaultAggregIpAddrType InetAddressType
  cGgsnDefaultAggregIpAddr InetAddress
  cGgsnDefaultAggregIpMask CiscoInetAddressMask
  cGgsnDefaultAggregRowStatus RowStatus

CGgsnPlmnIpAddrRangeEntry  
SEQUENCE    
  cGgsnPlmnAddrRangeIpAddrType InetAddressType
  cGgsnPlmnAddrRangeFirstIp InetAddress
  cGgsnPlmnAddrRangeLastIp InetAddress
  cGgsnPlmnAddrRangeRowStatus RowStatus
  cGgsnPlmnAddrRangeUsage INTEGER
  cGgsnPlmnAddrRangeFirstIpv6Prefixlen InetAddressPrefixLength
  cGgsnPlmnAddrRangeLastIpv6Prefixlen InetAddressPrefixLength

CGgsnPdfEntry  
SEQUENCE    
  cGgsnPdfGroupName SnmpAdminString
  cGgsnPdfDomainName InetAddressDNS
  cGgsnPdfIpAddressType InetAddressType
  cGgsnPdfIpAddress InetAddress
  cGgsnPdfRowStatus RowStatus
  cGgsnPdfReconnectTimeOut Unsigned32
  cGgsnPdfReconnectRetries Unsigned32
  cGgsnPdfReconExpPdpDelete TruthValue
  cGgsnPdfReqRetryTimeOut Unsigned32
  cGgsnPdfReqRetries Unsigned32

CGgsnPcscfEntry  
SEQUENCE    
  cGgsnPcscfGroupName SnmpAdminString
  cGgsnPcscfIpAddressType InetAddressType
  cGgsnPcscfIpAddress InetAddress
  cGgsnPcscfRowStatus RowStatus

CGgsnPlmnEntry  
SEQUENCE    
  cGgsnPlmnMcc SnmpAdminString
  cGgsnPlmnMnc SnmpAdminString
  cGgsnPlmnRowStatus RowStatus
  cGgsnPlmnScope INTEGER

CGgsnSlbVserverEntry  
SEQUENCE    
  cGgsnSlbVserAddrType InetAddressType
  cGgsnSlbVserAddress InetAddress
  cGgsnSlbVserNextHopAddrType InetAddressType
  cGgsnSlbVserNextHopAddress InetAddress
  cGgsnSlbVserVrfName SnmpAdminString
  cGgsnSlbVserRowStatus RowStatus

CGgsnGtpEncapsuEntry  
SEQUENCE    
  cGgsnGtpEncapsuInterface InterfaceIndexOrZero

Defined Values

cGgsnMIB 1.3.6.1.4.1.9.9.240
This MIB module manages the Gateway GPRS Support Node (GGSN) devices. A GGSN device provides interworking with external packet-data network of a particular GPRS service provider. It provides a combination of IP routing and GPRS specific functionality to support mobile users. GTP version1 is introduced in UMTS release 99 and Cisco GGSN will support both GTP version 1 (GTP v1) and version zero (GTP v0) simultaneously. GTP v1 supports multiple PDP contexts sharing one IP address. TFTs are introduced to achieve this. Each TFT is associated with a PDP context and there may exist one PDP context without TFT amongst all PDP contexts sharing the same IP address. Each TFT has one to eight packet filters each assigned with a precedence index. These packet filters are evaluated one at a time against the packet header information in sequence of their precedence index. A match is claimed if all the filters are matched and the PDP context that the TFT belongs to will be selected, else the checks are performed against the filters of another PDP context. If the packet header doesn't contain any TFT packet filter information, then the PDP context without the TFT is selected for further processing. Note on notifications: When an alarm occurs on the device, if the alarm's severity is higher than the severity filter threshold, a notification is generated by the device; and if cGgsnNotifEnabled is 'true', then the device's SNMP-engine configuration will be searched to determine where to send the notification. Acronyms and terms: APN Access Point Name CSG Content Service Gateway CDR Charging Data Record DCCA Diameter Credit Control Application ETSI European Telecommunications Standards Institute GGSN Gateway GPRS Support Node GPRS General Packet Radio Service GSM Global System for Mobile communication GTP GPRS Tunneling Protocol G-PDU GTP PDU IE Information Element MS Mobile Station MSISDN Mobile Station ISDN number PDP Packet Data Protocol PDU Protocol Data Unit PLMN Public Land Mobile Network SGSN Serving GPRS support Node SLB Server Load Balancing TFT Traffic Flow Template T-PDU the payload of G-PDU UMTS Universal Mobile Telecommunications System IMS IP Multimedia Subsystem COPS Common Open Policy Service protocol PEP Policy Enforcement Point PDF Policy Decision Function P-CSCF Proxy Call Session Control Function PLMN Public Land Mobile Network QS Quota Server UE User Equipment REFERENCE [1] GSM 03.60: Digital cellular telecommunications system (Phase 2+); General Packet Radio Service (GPRS); Service description; Stage 2. V7.1.0 [2] GSM 09.60: Digital cellular telecommunication system (Phase 2+); General Packet Radio Service (GPRS); GPRS Tunnelling Protocol (GTP) across Gn and Gp Interface. V7.3.0 [3] 3GPP; Technical Specification Group Services and System Aspects; QoS Concept and Architecture. 3G TS 23.107 v3.2.0. [4] 3GPP; Technical Specification Group Core Network; General Packet Radio Service(GPRS); GPRS Tunnelling Protocol (GTP) across Gn and Gp Interface (Release 1999). 3G TS 29.060 v3.5.0. [5] 3GPP: Technical Specification Group Core Network; Policy control over Go interface (Release 5). 3GPP TS 29.207 V5.2.0
MODULE-IDENTITY    

cGgsnMIBObjects 1.3.6.1.4.1.9.9.240.1
OBJECT IDENTIFIER    

cGgsnStatistics 1.3.6.1.4.1.9.9.240.1.1
OBJECT IDENTIFIER    

cGgsnNotifMgmt 1.3.6.1.4.1.9.9.240.1.2
OBJECT IDENTIFIER    

cGgsnConfigurations 1.3.6.1.4.1.9.9.240.1.3
OBJECT IDENTIFIER    

cGgsnStatus 1.3.6.1.4.1.9.9.240.1.4
OBJECT IDENTIFIER    

cGgsnNotifInfo 1.3.6.1.4.1.9.9.240.1.5
OBJECT IDENTIFIER    

cGgsnSentSigMessages 1.3.6.1.4.1.9.9.240.1.1.1
The number of GTPv0 and GTPv1 signalling messages sent. Trigger Condition: This counter is updated whenever a GTPv0 and GTPv1 signalling messages is sent out, including retries.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnReceivedSigMessages 1.3.6.1.4.1.9.9.240.1.1.2
The number of GTPv0 and GTPv1 signalling messages received. Trigger Condition: This counter is updated whenever a GTPv0 and GTPv1 signalling message is received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnUnexpectedSigMessages 1.3.6.1.4.1.9.9.240.1.1.3
The number of unexpected GTP signalling messages received. Trigger Condition: This counter is updated whenever an unexpected Signalling message is received. Condition includes, a) A Response message for which there is no corresponding outstanding Request. b) A GTP control plane message a GSN is not expected to handle (such as a PDU Notification Request received by a GGSN). c) Charging messages in GTP path and vice-versa. d) LFN bit not being set when CG path uses short-header and vice-versa.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnSentGPDUs 1.3.6.1.4.1.9.9.240.1.1.4
The number of G-PDU messages sent. Trigger Condition: This counter is updated whenever a G-PDU is sent out by the GGSN.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnReceivedGPDUs 1.3.6.1.4.1.9.9.240.1.1.5
The number of G-PDU messages received. Trigger Condition: This counter is incremented for each G-PDU received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnSentGPDUOctets 1.3.6.1.4.1.9.9.240.1.1.6
The number of total bytes sent in G-PDU messages. Trigger Condition: This counter is updated whenever a G-PDU is sent out by the GGSN.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnReceivedGPDUOctets 1.3.6.1.4.1.9.9.240.1.1.7
The number of total bytes received in G-PDU messages. Trigger Condition: This counter is incremented for each G-PDU received.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnUnexpectedGPDUs 1.3.6.1.4.1.9.9.240.1.1.8
The number of unexpected G-PDU messages, for example, non existent PDP contexts and ACL denial. Trigger Condition: This counter is updated whenever an unexpected G-PDU message is received. Conditions include, a) G-PDU for a non existent PDP. b) ACL denial.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnActivationRejectedPdps 1.3.6.1.4.1.9.9.240.1.1.9
The number of PDP contexts that the activation request was rejected. Trigger Condition: This counter is updated when a PDP activation request is rejected. The cause for rejection can be a) Resource limitations like max PDP limit is reached, Out of memory. b) Config restrictions like trying to create NIPDP on an APN on which the same is disabled, c) Creating secondary contexts on PPP/PPP-Regen PDPs.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnOutOfResourcePdps 1.3.6.1.4.1.9.9.240.1.1.10
The number of PDP contexts that the activation request rejected due to the GGSN running out of resources for transmitting GTP packets. Examples: - Out of memory; - The number of PDPs on GGSN reached limit; - all dynamic PDP address are occupied; Trigger Condition: a) Out of memory. b) Number of PDPs on GGSN reached limit. c) Number of of PPP-regen PDPs reaches max limit. d) All dynamic PDP address are occupied. e) Incorrect configs for create pdp req. f) Qos negotiation fails. g) Create PDP req received for non-transparent APN but no radius server is present for authorization. h) Attempt to create a PDP with IP address that is already in use. i) Attempt to create a PPP-Regen PDP but the vtemplate for PPP-regen is not properly configured or VPDN configs are not proper. j) Number of pending signalling messages that needs to be processed by the GGSN is beyond the max limit(100).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnParserErrorMessages 1.3.6.1.4.1.9.9.240.1.1.11
The number of GTP messages received with wrong value. It includes the following cases: - mandatory and optional information element in the GTP packet is duplicated, missing, unknown, incorrect or out of order. - the GTP message is too short to hold the GTP header for the supported version. - the GTP messages running an unsupported version of GTP. - Unknown GTP message type. Trigger Condition: This counter is triggered when a signalling message is received with parsing related errors such as missing/unknown/invalid/unexpected/duplicate mandatory/optional IE's in the messages.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnTotalCreatedPdps 1.3.6.1.4.1.9.9.240.1.1.12
This object represents the total number of PDP contexts created. Trigger Condition: This counter is updated whenever a PDP context is created. This includes static, dynamic, IP, PPP, network init PDPs.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnTotalDeletedPdps 1.3.6.1.4.1.9.9.240.1.1.13
This object represents the total number of PDP contexts deleted. Trigger Condition: This counter is updated whenever a PDP context is deleted. This includes static, dynamic, IP, PPP, network init PDPs.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnTotalNetworkInitPdps 1.3.6.1.4.1.9.9.240.1.1.14
This object represents the total number of PDP contexts activated by the GGSN that were initiated by the PDN. Trigger Condition: This counter will be updated on successful creation of network initiated PDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnTotalPppPdpsCreated 1.3.6.1.4.1.9.9.240.1.1.15
This object represents the total number of PPP PDP contexts created. Trigger Condition: This counter is updated whenever a PPP PDP context is created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnTotalPppPdpsDeleted 1.3.6.1.4.1.9.9.240.1.1.16
This object represents the total number of PPP PDP contexts deleted. Trigger Condition: This counter is updated whenever a PPP PDP context is deleted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnOutOfResourcePppRegenPdps 1.3.6.1.4.1.9.9.240.1.1.17
This object represents the total number of create PDP context and delete PDP context requests rejected due to unavailable resource on the GGSN for PPP regeneration. Trigger Condition: a) Out of memory. b) Number of PPP-regen PDPs reaches max limit. c) All dynamic PDP address are occupied. d) Attempt to create a PPP-Regen PDP but the vtemplate for PPP-regen is not properly configured or VPDN configs are not proper.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnDroppedPppRegenPdps 1.3.6.1.4.1.9.9.240.1.1.18
This object represents the total number of create PDP context and delete PDP context requests that were dropped due to the threshold limit being reached for maximum number of PPP regeneration sessions allowed on the GGSN. Trigger Condition: This counter is updated when a new PPP regen PDP activation request is received by GGSN and max allowed PPP Regen session is reached.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnTftSemanticErrorPdps 1.3.6.1.4.1.9.9.240.1.1.19
This object represents the total number of received PDP context messages that had TFTs with semantic errors. Trigger Condition: This counter is triggered by the create, update PDP context request message.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnTftSyntacticErrorPdps 1.3.6.1.4.1.9.9.240.1.1.20
This object represents the total number of received PDP context messages that had TFTs with syntactic errors. Trigger Condition: This counter is triggered by the create, update PDP context request message.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnPktFilterSemanticErrorPdps 1.3.6.1.4.1.9.9.240.1.1.21
This object represents the total number of received PDP context messages that had packet filters with semantic errors. Trigger Condition: This counter is triggered by the create, update PDP context request message.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnPktFilterSyntacticErrorPdps 1.3.6.1.4.1.9.9.240.1.1.22
This object represents the total number of received PDP context messages that had packet filters with syntactic errors. Trigger Condition: This counter is triggered by the create, update PDP context request message.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnHCSentGPDUOctets 1.3.6.1.4.1.9.9.240.1.1.23
The number of total bytes sent in G-PDU messages. Trigger Condition: This counter is updated whenever a G-PDU is sent out by the GGSN.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

cGgsnHCReceivedGPDUOctets 1.3.6.1.4.1.9.9.240.1.1.24
The number of total bytes received in G-PDU messages. Trigger Condition: This counter is incremented for each G-PDU received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

cGgsnPdpsRejStatistics 1.3.6.1.4.1.9.9.240.1.1.25
OBJECT IDENTIFIER    

cGgsnVersionNotSupportedRejPdps 1.3.6.1.4.1.9.9.240.1.1.25.1
The number of PDP contexts that were rejected due to the cause of Version Not Supported. Trigger Condition: This counter is triggered by create/update PDP / PPP PDP context request message. This object is deprecated by cGgsnVersionNotSupportedMsgs.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnUnkownMessageRejPdps 1.3.6.1.4.1.9.9.240.1.1.25.2
The number of PDP contexts that were rejected due to the cause of Unknown Message. Trigger Condition: This counter is triggered by create/update PDP / PPP PDP context request message. This object is deprecated by cGgsnUnkownGtpMsgs.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnMsgTooShortRejPdps 1.3.6.1.4.1.9.9.240.1.1.25.3
The number of PDP contexts that were rejected due to the cause of Message Too Short. Trigger Condition: This counter is triggered by create/update PDP / PPP PDP context request message. This object is deprecated by cGgsnTooShortMsgs.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnMandIeMissingRejPdps 1.3.6.1.4.1.9.9.240.1.1.25.4
The number of PDP contexts that were rejected due to the cause of Mandatory IE Missing. Trigger Condition: This counter is triggered by create/update PDP / PPP PDP context request message. This object is deprecated by cGgsnMandIeMissingMsgs.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnMandIeIncorrectRejPdps 1.3.6.1.4.1.9.9.240.1.1.25.5
The number of PDP contexts that were rejected due to the cause of Mandatory IE Incorrect. Trigger Condition: This counter is triggered by create/update PDP / PPP PDP context request message. This object is deprecated by cGgsnMandIeIncorrectMsgs.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnOptIeInvalidRejPdps 1.3.6.1.4.1.9.9.240.1.1.25.6
The number of PDP contexts that rejected due to the cause of Optional IE Invalid. Trigger Condition: This counter is triggered by create/update PDP / PPP PDP context request message. This object is deprecated by cGgsnOptIeInvalidMsgs.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnIeUnknownRejPdps 1.3.6.1.4.1.9.9.240.1.1.25.7
The number of PDP contexts that rejected due to the cause of IE Unknown. Trigger Condition: This counter is triggered by create/update PDP / PPP PDP context request message. This object is deprecated by cGgsnIeUnknownMsgs.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnIeOutOfOrderRejPdps 1.3.6.1.4.1.9.9.240.1.1.25.8
The number of PDP contexts that rejected due to the cause of IE Out of Order. Trigger Condition: This counter is triggered by create/update PDP / PPP PDP context request message. This object is deprecated by cGgsnIeOutOfOrderMsgs.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnIeUnexpectedRejPdps 1.3.6.1.4.1.9.9.240.1.1.25.9
The number of PDP contexts that rejected due to the cause of IE Unexpected. Trigger Condition: This counter is triggered by create/update PDP / PPP PDP context request message. This object is deprecated by cGgsnIeUnexpectedMsgs.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnIeDuplicatedRejPdps 1.3.6.1.4.1.9.9.240.1.1.25.10
The number of PDP contexts that rejected due to the cause of IE Duplicated. Trigger Condition: This counter is triggered by create/update PDP / PPP PDP context request message. This object is deprecated by cGgsnIeDuplicatedMsgs.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnOptIeIncorrectRejPdps 1.3.6.1.4.1.9.9.240.1.1.25.11
The number of PDP contexts that rejected due to the cause of Optional IE Incorrect. Trigger Condition: This counter is triggered by create/update PDP / PPP PDP context request message. This object is deprecated by cGgsnOptIeIncorrectMsgs.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnPdpWithoutTftExistsRejPdps 1.3.6.1.4.1.9.9.240.1.1.25.12
The number of PDP contexts that are rejected due to the cause of PDP context without TFT already exists. Trigger Condition: This counter is triggered by create/update PDP / PPP PDP context request message. This object is deprecated by cGgsnPdpWithoutTftExistsPdps.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnSgsnStatTable 1.3.6.1.4.1.9.9.240.1.1.26
This table has the statistics of the interface (Gi, Gn, Gp) upstream and downstream traffic per SGSN for a configurable duration set in cGgsnThruputIntervalOne and cGgsnThruputIntervalTwo. Creation of row(s) will happen when there is a valid value set to cGgsnThruputIntervalOne or cGgsnThruputIntervalTwo and when a PATH is established. Deletion of row(s) will happen when either the PATH gets removed or the throughput intervals(cGgsnThruputIntervalOne, cGgsnThruputIntervalTwo) is unset.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CGgsnSgsnStatEntry

cGgsnSgsnStatEntry 1.3.6.1.4.1.9.9.240.1.1.26.1
An entry in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  CGgsnSgsnStatEntry  

cGgsnSgsnThruPutInterval 1.3.6.1.4.1.9.9.240.1.1.26.1.1
This object should be one of the values set in the objects cGgsnThruputIntervalOne or cGgsnThruputIntervalTwo except for value '0', which means the throughput collection is disabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

cGgsnSgsnThruPutLastCollected 1.3.6.1.4.1.9.9.240.1.1.26.1.2
This object represents the delta value between the time when this data is collected and the time it is been retrieved.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

cGgsnSgsnUpStreamPktCnt 1.3.6.1.4.1.9.9.240.1.1.26.1.3
This object represents the total number of upstream packets sent on this SGSN data path. Data flow from MS to PDN is considered to be upstream traffic. When the throughput intervals (cGgsnThruputIntervalOne or cGgsnThruputIntervalTwo) is set to some valid value this object is set to '0' (meaning, a fresh throughput collection is started). Until the first expiry of the throughput interval , this object will be '0'. On further periodic expiry, the throughput upstream packet count per SGSN is collected and updated to this object
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnSgsnUpStreamByteCnt 1.3.6.1.4.1.9.9.240.1.1.26.1.4
This object represents the total number of upstream bytes sent on this SGSN data path. Data flow from MS to PDN is considered to be upstream traffic. When the throughput intervals (cGgsnThruputIntervalOne or cGgsnThruputIntervalTwo) is set to some valid value this object is set to '0' (meaning, a fresh throughput collection is started). Until the first expiry of the throughput interval , this object will be '0'. On further periodic expiry, the throughput upstream byte count per SGSN is collected and updated to this object
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnSgsnDownStreamPktCnt 1.3.6.1.4.1.9.9.240.1.1.26.1.5
This object represents the total number of downstream packets sent on this SGSN data path. Data flow from PDN to MS is considered to be downstream traffic. When the throughput interval (cGgsnThruputIntervalOne or cGgsnThruputIntervalTwo) is set to some valid value, this object is set to '0' (meaning, a fresh throughput collection is started). Until the first expiry of the throughput interval , this object will be '0'. On further periodic expiry, the throughput downstream packet count per SGSN is collected and updated to this object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnSgsnDownStreamByteCnt 1.3.6.1.4.1.9.9.240.1.1.26.1.6
This object represents the total number of downstream bytes sent on this SGSN data path. Data flow from PDN to MS is considered to be downstream traffic. When the throughput interval (cGgsnThruputIntervalOne or cGgsnThruputIntervalTwo) is set to some valid value, this object is set to '0' (meaning, a fresh throughput collection is started). Until the first expiry of the throughput interval , this object will be '0'. On further periodic expiry, the throughput downstream byte count per SGSN is collected and updated to this object.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnRedundancyStatistics 1.3.6.1.4.1.9.9.240.1.1.27
OBJECT IDENTIFIER    

cGgsnTotalMessages 1.3.6.1.4.1.9.9.240.1.1.27.1
This counter will maintain the count of total number of messages of all kind. Trigger Condition: The counter is increamented whenever a redundancy message is sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnContextSetupMessages 1.3.6.1.4.1.9.9.240.1.1.27.2
The PDP context is check pointed to standby only after it goes to active. This object is a counter, which maintains the total count of PDP context setup messages. Trigger Condition: This counter is updated whenever a PDP context setup message is check pointed to standby.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnContextModifyMessages 1.3.6.1.4.1.9.9.240.1.1.27.3
For modify or update PDP context, the categories get affected and new quota is assigned to them. This new info must be check pointed to the standby. This object maintains the total number of context modify messages which are check pointed to standby. Trigger Condition: This counter is incremented whenever a context modify message is check pointed to standby.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnContextRemoveMessages 1.3.6.1.4.1.9.9.240.1.1.27.4
When the PDP context is deleted, deletion event is check pointed to the standby, so that the corresponding backup context deleted as well. This object will maintain the total number of context removed messages which are check pointed to standby. Trigger Condition: The counter is incremented for every context remove message, which is check pointed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnPathSetupMessages 1.3.6.1.4.1.9.9.240.1.1.27.5
Messages (of any kind PDP create/delete etc)indicate the presence of other GSN. Path is setup between the GSNs when they transmit the messages. This object contains the number of path setup messages between SGSN and GGSN. Trigger Condition: This counter is updated for every path setup messages sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnPathModifyMessages 1.3.6.1.4.1.9.9.240.1.1.27.6
This object will contain the total number of path Modify messages. The IE recovery count is used to indicate restart of other GSN. Any change related to path or GSN will be check pointed to standby. Trigger Condition: This counter is incremented for every change related to path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnPathRemoveMessages 1.3.6.1.4.1.9.9.240.1.1.27.7
This object will keep track of all the messages which are responsible for path removal between the GSNs. As long as context remain established, the path between the GSNs is alive. In an instant where the last context is released and the echo timer is not enabled, the path timer is started within which the PDP context is expected to keep the path live, when the timer expires, path is Removed. Trigger Condition: This timer is triggered when the path between the GSNs is removed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnCGFReadyMessages 1.3.6.1.4.1.9.9.240.1.1.27.8
The charging information are sent from GGSN to charging gateway. GTP' protocol is used between them. This object will consists of total number of CGF ready messages. Trigger Condition: The counter is incremented when CGF ready message is check pointed to standby.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnCGFModifyMessages 1.3.6.1.4.1.9.9.240.1.1.27.9
Significant information related to change in state of CGF must be check pointed to GGSN. This object indicates the total number of CGF modify messages recieved. Trigger condition: This counter is triggered when there is a change in CGF state.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnCGFRemoveMessages 1.3.6.1.4.1.9.9.240.1.1.27.10
This object maintains the count for all the messages responsible for CGF removal Trigger Condition: This counter is triggered when context is deleted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnInternalStateMsgs 1.3.6.1.4.1.9.9.240.1.1.27.11
The GGSN certain information which are sent out to other GSN's (SGSN) and CGF. On failover these information must be consistent. Information like, IE recovery count sent to the other GSN's for path management, local record sequence number and charging ID etc. Trigger Condition: The counter is incremented for each of these kind of messages.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnSlbCacFailures 1.3.6.1.4.1.9.9.240.1.1.28
This object will keep track of number of CAC Failure notifications sent to SLB. Trigger Condition: The counter is incremented whenever GGSN sends CAC failure notification to SLB.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnSlbSessionFailures 1.3.6.1.4.1.9.9.240.1.1.29
This object will keep track of number of Session failure notifications sent to SLB. Trigger Condition: The counter is incremented whenever GGSN sends Session failure notification to SLB.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnTotalCreatedIpv6Pdps 1.3.6.1.4.1.9.9.240.1.1.30
This object represents the total number of successfully created ipv6 PDP contexts. Trigger Condition: The counter is incremented whenever a ipv6 PDP context is created. This includes static, dynamic, IP PDPs.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnTotalDeletedIpv6Pdps 1.3.6.1.4.1.9.9.240.1.1.31
This object represents the total number of ipv6 PDP contexts deleted. Trigger Condition: The counter is incremented whenever a ipv6 PDP context is deleted. This includes static, dynamic, IP, PPP PDPs.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnTotalRejectedIpv6Pdps 1.3.6.1.4.1.9.9.240.1.1.32
This object represents the total number of rejected ipv6 PDP context activation requests. Trigger Condition: The counter is incremented when a ipv6 PDP activation request is rejected.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnSentIpv6SigMessages 1.3.6.1.4.1.9.9.240.1.1.33
The total number of GTP signalling messages related to the IPv6 PDP sent by GGSN. Trigger Condition: The counter is incremented whenever a GTP signalling message for IPv6 PDP is sent out, including retries.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnReceivedIpv6SigMessages 1.3.6.1.4.1.9.9.240.1.1.34
The total number of GTP signalling messages related to the IPv6 PDP received by GGSN. Trigger Condition: The counter is incremented whenever a GTP signalling message for IPv6 PDP is received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnSentIpv6PDUs 1.3.6.1.4.1.9.9.240.1.1.35
The number of ipv6 data packets sent by GGSN. Trigger Condition: The counter is incremented whenever a G-PDU is sent out by the GGSN.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnReceivedIpv6PDUs 1.3.6.1.4.1.9.9.240.1.1.36
The number of ipv6 data packets receivd by GGSN. Trigger Condition: This counter is incremented for each G-PDU received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnSentIpv6PDUOctets 1.3.6.1.4.1.9.9.240.1.1.37
The number of ipv6 data bytes sent, in PDU messages, by GGSN. Trigger Condition: The counter is incremented whenever a G-PDU is sent out by the GGSN.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

cGgsnReceivedIpv6PDUOctets 1.3.6.1.4.1.9.9.240.1.1.38
The number of ipv6 data bytes received, in PDU messages, by GGSN. Trigger Condition: The counter is incremented for each G-PDU received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

cGgsnVersionNotSupportedMsgs 1.3.6.1.4.1.9.9.240.1.1.39
The number of GTP messages received from devices running an unsupported version of the GTP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnUnkownGtpMsgs 1.3.6.1.4.1.9.9.240.1.1.40
The number of unknown GTP messages received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnTooShortMsgs 1.3.6.1.4.1.9.9.240.1.1.41
The number of GTP messages received that are too short to hold the GTP header for the supported GTP version.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnMandIeMissingMsgs 1.3.6.1.4.1.9.9.240.1.1.42
The number of GTP messages received with a missing mandatory information element.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnMandIeIncorrectMsgs 1.3.6.1.4.1.9.9.240.1.1.43
The number of GTP messages received with an incorrect mandatory information element, for example, with an information element that has an incorrect length.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnOptIeInvalidMsgs 1.3.6.1.4.1.9.9.240.1.1.44
The number of GTP messages received with an information element that contains a value that is not within the defined range for that IE. GTP messages with invalid optional IEs are processed as if the IE was not present.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnIeUnknownMsgs 1.3.6.1.4.1.9.9.240.1.1.45
The number of GTP messages received with an information element of an unknown type.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnIeOutOfOrderMsgs 1.3.6.1.4.1.9.9.240.1.1.46
The number of GTP messages received with an information element out of order.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnIeUnexpectedMsgs 1.3.6.1.4.1.9.9.240.1.1.47
The number of GTP messages received with an information element that is not expected in the GTP message, but is defined in GTP. GTP messages with unexpected IEs are processed as if the IE was not present.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnIeDuplicatedMsgs 1.3.6.1.4.1.9.9.240.1.1.48
The number of GTP messages received with a duplicated information element.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnOptIeIncorrectMsgs 1.3.6.1.4.1.9.9.240.1.1.49
The number of GTP messages received with an optional IE that is incorrect, which prevents the GGSN from processing the GTP message correctly.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnPdpWithoutTftExistsPdps 1.3.6.1.4.1.9.9.240.1.1.50
The number of create PDP context requests received without traffic flow template information element.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnNotifEnabled 1.3.6.1.4.1.9.9.240.1.2.1
Indicates whether cGgsnNotification notification will be sent when a notification is generated by the device. - 'true', it will enable the device to send a notification, as well as logging the notification to the cGgsnHistNotifTable. - 'false', it will prevent the device from sending out a notification, but it will still log the notification into cGgsnHistNotifTable.
Status: deprecated Access: read-write
OBJECT-TYPE    
  TruthValue  

cGgsnNotifLeastSeverLevel 1.3.6.1.4.1.9.9.240.1.2.2
Indicates the least severity level of the cGgsnNotification notifications to be generated by the device. Thus, notifications are not generated for alarms with a severity level less urgent than the value of this object. This object cannot be set to cleared(1) or indeterminate(2).
Status: current Access: read-write
OBJECT-TYPE    
  CiscoAlarmSeverity  

cGgsnGeneratedNotifs 1.3.6.1.4.1.9.9.240.1.2.3
The number of cGgsnNotification notifications that have been generated since sysUpTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnIgnoredAlarms 1.3.6.1.4.1.9.9.240.1.2.4
The number of alarms which are less severe than cGgsnNotifLeastSeverLevel since sysUpTime, and thus, for which no notification was generated.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cGgsnHistNotifMaxLength 1.3.6.1.4.1.9.9.240.1.2.5
The maximum number of entries to be retained in the cGgsnHistNotifTable. When the table is full, the oldest entries are removed to make space for new entries.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..2147483647  

cGgsnHistNotifLatestIndex 1.3.6.1.4.1.9.9.240.1.2.6
The value of cGgsnHistNotifIndex for the most recently created entry in cGgsnHistNotifTable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cGgsnHistNotifTable 1.3.6.1.4.1.9.9.240.1.2.7
A history table of the most recent cGgsnNotification notifications generated by this device. If a new cGgsnNotification notification is generated when the number of entries is equal to cGgsnHistNotifMaxLength, then the oldest entry is deleted and replaced with an entry for the latest notification.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CGgsnHistNotifEntry

cGgsnHistNotifEntry 1.3.6.1.4.1.9.9.240.1.2.7.1
Detailed information concerning a particular notification that previously generated from this device.
Status: current Access: not-accessible
OBJECT-TYPE    
  CGgsnHistNotifEntry  

cGgsnHistNotifIndex 1.3.6.1.4.1.9.9.240.1.2.7.1.1
A monotonically increasing integer for the sole purpose of indexing notifications. When it reaches the maximum value, it wraps the value back to 1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cGgsnHistNotifType 1.3.6.1.4.1.9.9.240.1.2.7.1.2
This object indicates the type of notification.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ggsnServiceUp(1), ggsnServiceDown(2), mapSgsnUp(3), mapSgsnDown(4), noResource(5), noRADIUS(6), noDHCPServer(7), ipAllocationFail(8), authenticationFail(9), apnUnreachable(10)  

cGgsnHistNotifSeverity 1.3.6.1.4.1.9.9.240.1.2.7.1.3
This object indicates the severity level of the notification. This object cannot be set to cleared(1) or indeterminate(2).
Status: current Access: read-only
OBJECT-TYPE    
  CiscoAlarmSeverity  

cGgsnHistNotifTimestamp 1.3.6.1.4.1.9.9.240.1.2.7.1.4
This object indicates the value of sysUpTime when this notification was generated.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cGgsnHistNotifGgsnIpAddrType 1.3.6.1.4.1.9.9.240.1.2.7.1.5
This object indicates the type of Internet address by which cGgsnHistNotifGgsnIpAddr is reachable.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

cGgsnHistNotifGgsnIpAddr 1.3.6.1.4.1.9.9.240.1.2.7.1.6
The object indicates the IP address that uniquely identifies the device which generated the notification.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

cGgsnHistNotifInfo 1.3.6.1.4.1.9.9.240.1.2.7.1.7
A textual description of cGgsnHistNotifType, which potentially contains additional information (more than just the type of alarm). If the text of the message exceeds 64 bytes, the message will be truncated to 63 bytes and a '*' character will be appended to indicate the message has been truncated.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..64)  

cGgsnServiceNotifEnabled 1.3.6.1.4.1.9.9.240.1.2.8
Indicates whether cGgsnInServiceNotif notification and cGgsnMaintenanceNotif notification will be sent when a notification is generated by the device. - 'true', it will enable the device to send a notification. - 'false', it will prevent the device from sending out a notification.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cGgsnMemoryNotifEnabled 1.3.6.1.4.1.9.9.240.1.2.9
Indicates whether cGgsnMemThresholdReachedNotif notification and cGgsnMemThresholdClearedNotif notification will be sent when a notification is generated by the device. - 'true', it will enable the device to send a notification. - 'false', it will prevent the device from sending out a notification.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cGgsnPdfNotifEnabled 1.3.6.1.4.1.9.9.240.1.2.10
Indicates whether cGgsnPdfStateUpNotif notification and cGgsnPdfStateDownNotiff notification will be sent when a notification is generated by the device. - 'true', it will enable the device to send a notification. - 'false', it will prevent the device from sending out a notification.
Status: deprecated Access: read-write
OBJECT-TYPE    
  TruthValue  

cGgsnGlobalErrorNotifEnabled 1.3.6.1.4.1.9.9.240.1.2.11
Indicates whether cGgsnGlobalErrorNotif notification will be sent when a notification is generated by the device. - 'true', it will enable the device to send a notification. - 'false', it will prevent the device from sending out a notification.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cGgsnAccessPointNotifEnabled 1.3.6.1.4.1.9.9.240.1.2.12
Indicates whether cGgsnAccessPointNameNotif notification will be sent when a notification is generated by the device. - 'true', it will enable the device to send a notification. - 'false', it will prevent the device from sending out a notification.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cGgsnPdpNotifEnabled 1.3.6.1.4.1.9.9.240.1.2.13
Indicates whether cGgsnPacketDataProtocolNotif notification will be sent when a notification is generated by the device. - 'true', it will enable the device to send a notification. - 'false', it will prevent the device from sending out a notification.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cGgsnDefaultIpAllocationMethod 1.3.6.1.4.1.9.9.240.1.3.1
Specifies the default method by which the GGSN obtains address leases for mobile user sessions. - 'disable', which indicates that dynamic address allocation is disabled. - 'dhcp', which indicates that the DHCP server will be used. - 'radius', which indicates that the radius server will be used.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), dhcp(2), radius(3)  

cGgsnIdlePdpPurgeTimer 1.3.6.1.4.1.9.9.240.1.3.2
This object specifies the time that the GGSN waits before purging idle PDP contexts. A value '0' will disable the purge timer.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

cGgsnIpDupProtectTable 1.3.6.1.4.1.9.9.240.1.3.3
This table contains the range of IP address used in the GPRS PLMN. These IP addresses are used to avoid IP address duplication in GPRS network. IP address duplication occurs when a MS uses an IP address which is already used in the PLMN. The IP addresses configured inside GPRS network should be in these ranges and MS IP address should not be in this range.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CGgsnIpDupProtectEntry

cGgsnIpDupProtectEntry 1.3.6.1.4.1.9.9.240.1.3.3.1
Entry containing the start and end IP address in the address range. An Entry with start IP > end IP is not allowed. No new entry will be accepted if that would cause any IP address(es) to be represented by more than one row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  CGgsnIpDupProtectEntry  

cGgsnMsExcludeRangeStartIpType 1.3.6.1.4.1.9.9.240.1.3.3.1.1
The type of Internet address by which cGgsnMsExcludeRangeStartIp is reachable. The value of this object should be same as cGgsnMsExcludeRangeEndIpType.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

cGgsnMsExcludeRangeStartIp 1.3.6.1.4.1.9.9.240.1.3.3.1.2
Starting IP address in the address range.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4..20)  

cGgsnMsExcludeRangeEndIpType 1.3.6.1.4.1.9.9.240.1.3.3.1.3
The type of Internet address by which cGgsnMsExcludeRangeEndIp is reachable. The value of this object should be same as cGgsnMsExcludeRangeStartIpType.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

cGgsnMsExcludeRangeEndIp 1.3.6.1.4.1.9.9.240.1.3.3.1.4
Ending IP address in the address range.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4..20)  

cGgsnIpDupProtectRowStatus 1.3.6.1.4.1.9.9.240.1.3.3.1.5
This object is used to create a new row or delete an existing row in this table. To create a row, set this object to 'createAndGo' and the objects cGgsnMsExcludeRangeStartIpv6Prefixlen and cGgsnMsExcludeRangeEndIpv6Prefixlen should be set to valid values. To delete a row, set this object to 'destroy'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cGgsnMsExcludeRangeStartIpv6Prefixlen 1.3.6.1.4.1.9.9.240.1.3.3.1.6
This object represents the IPv6 prefix length supplied for the cGgsnMsExcludeRangeStartIp.The value of this object will be zero when cGgsnMsExcludeRangeStartIpType is IPv4.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressPrefixLength  

cGgsnMsExcludeRangeEndIpv6Prefixlen 1.3.6.1.4.1.9.9.240.1.3.3.1.7
This object represents the IPv6 prefix length supplied for the cGgsnMsExcludeRangeEndIp.The value of this object will be zero when cGgsnMsExcludeRangeEndIpType is IPv4.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressPrefixLength  

cGgsnDefaultAggregTable 1.3.6.1.4.1.9.9.240.1.3.4
This table contains the list of default aggregate routes configured on the GGSN. GGSN uses a static host route to forward user data packets for each PDP context received from Gi interface to Gn interface. Using the aggregate route (address range), the total number of static routes implemented in the GGSN for PDP requests can be greatly reduced.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CGgsnDefaultAggregEntry

cGgsnDefaultAggregEntry 1.3.6.1.4.1.9.9.240.1.3.4.1
An Entry contains the IP network prefix which is used to combine the routes of PDP requests for the same network as a single route on the GGSN.
Status: current Access: not-accessible
OBJECT-TYPE    
  CGgsnDefaultAggregEntry  

cGgsnDefaultAggregIpAddrType 1.3.6.1.4.1.9.9.240.1.3.4.1.1
This object specifies the type of Internet address denoted by cGgsnDefaultAggregIpAddr.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

cGgsnDefaultAggregIpAddr 1.3.6.1.4.1.9.9.240.1.3.4.1.2
This object specifies the IP address whose network prefix is going to be defined by cGgsnDefaultAggregIpMask.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4..20)  

cGgsnDefaultAggregIpMask 1.3.6.1.4.1.9.9.240.1.3.4.1.3
This object specifies the net-mask pertaining to cGgsnDefaultAggregIpAddr.
Status: current Access: not-accessible
OBJECT-TYPE    
  CiscoInetAddressMask  

cGgsnDefaultAggregRowStatus 1.3.6.1.4.1.9.9.240.1.3.4.1.4
This object is used to create a new row or delete an existing row in this table. To create a row, set this object to 'createAndGo'. To delete a row, set this object to 'destroy'. The values 'createAndWait' and 'notInService' are not supported.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cGgsnDefaultAaaAuthServerGroup 1.3.6.1.4.1.9.9.240.1.3.5
This object specifies the AAA radius server group that is used for authentication by all APN's on this GGSN.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

cGgsnDefaultAaaAccServerGroup 1.3.6.1.4.1.9.9.240.1.3.6
This object specifies the AAA radius server group that is used for accounting by all APN's on this GGSN.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

cGgsnPppVirtualTemplate 1.3.6.1.4.1.9.9.240.1.3.7
This object represents the virtual template interface used by PPP Type PDP's.
Status: current Access: read-write
OBJECT-TYPE    
  InterfaceIndexOrZero  

cGgsnPppRegenVirtualTemplate 1.3.6.1.4.1.9.9.240.1.3.8
This object represents the virtual template interface used for PPP Regeneration by the APN's on which PPP Regeneration is configured. The value zero indicates that no interface is specified.
Status: current Access: read-write
OBJECT-TYPE    
  InterfaceIndexOrZero  

cGgsnPlmnIpAddrRangeTable 1.3.6.1.4.1.9.9.240.1.3.9
This table contains the range of IP addresses that belong to the PLMN nodes in a GPRS network. This range does not include address of various entities like RADIUS, DHCP, DNS servers, etc., which are not part of PLMN.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CGgsnPlmnIpAddrRangeEntry

cGgsnPlmnIpAddrRangeEntry 1.3.6.1.4.1.9.9.240.1.3.9.1
Entry containing the first and last IP address in the address range. An Entry with first-IP > last-IP is not allowed. No new entry will be accepted if that would cause any IP address(es) to be represented by more than one row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  CGgsnPlmnIpAddrRangeEntry  

cGgsnPlmnAddrRangeIpAddrType 1.3.6.1.4.1.9.9.240.1.3.9.1.1
The address type for cGgsnPlmnAddrRangeFirstIp and cGgsnPlmnAddrRangeLastIp addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

cGgsnPlmnAddrRangeFirstIp 1.3.6.1.4.1.9.9.240.1.3.9.1.2
First IP address in the address range.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4..20)  

cGgsnPlmnAddrRangeLastIp 1.3.6.1.4.1.9.9.240.1.3.9.1.3
Last IP address in the address range.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4..20)  

cGgsnPlmnAddrRangeRowStatus 1.3.6.1.4.1.9.9.240.1.3.9.1.4
This object is used to create a new row or delete an existing row in this table. To create a row, set this object to 'createAndGo' and the objects cGgsnPlmnAddrRangeFirstIpv6Prefixlen and cGgsnPlmnAddrRangeLastIpv6Prefixlen should be set to valid values. To delete a row, set this object to 'destroy'. To modify a row, the row needs to be deleted and created fresh with new values.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cGgsnPlmnAddrRangeUsage 1.3.6.1.4.1.9.9.240.1.3.9.1.5
This object specifies how the address range will be used by the GGSN. When set to 'security', the address range is used for GGSN security feature i.e. any TPDU with destination address that falls in this address range will be discarded. When set to 'sgsn', the address range denotes the sgsn address range in the local PLMN which can be used to check roaming MS.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER security(1), sgsn(2)  

cGgsnPlmnAddrRangeFirstIpv6Prefixlen 1.3.6.1.4.1.9.9.240.1.3.9.1.6
This object represents the IPv6 prefix length supplied for the cGgsnPlmnAddrRangeFirstIp .The value of this object will be zero when cGgsnPlmnAddrRangeFirstIpType is IPv4.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressPrefixLength  

cGgsnPlmnAddrRangeLastIpv6Prefixlen 1.3.6.1.4.1.9.9.240.1.3.9.1.7
This object represents the IPv6 prefix length supplied for the cGgsnPlmnAddrRangeLastIp .The value of this object will be zero when cGgsnPlmnAddrRangeLastIpType is IPv4.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressPrefixLength  

cGgsnImsConfigurations 1.3.6.1.4.1.9.9.240.1.3.10
OBJECT IDENTIFIER    

cGgsnPdfTable 1.3.6.1.4.1.9.9.240.1.3.10.1
This table contains the details of PDF server that the GGSN supports. The table elements describes their properties. PDF's are the server's to which the client GGSN makes the TCP connection using the COPS protocol over the Go interface. GGSN can have connections with multiple PDF's.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CGgsnPdfEntry

cGgsnPdfEntry 1.3.6.1.4.1.9.9.240.1.3.10.1.1
Entry containing the PDF servers details (name and IP address) and also how the GGSN should communicate with PDF, like timeout when there is no response, number of retries.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  CGgsnPdfEntry  

cGgsnPdfGroupName 1.3.6.1.4.1.9.9.240.1.3.10.1.1.1
This object specifies the PDF group name. Currently this group name is just an identity to this group.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..100)  

cGgsnPdfDomainName 1.3.6.1.4.1.9.9.240.1.3.10.1.1.2
This is a Fully Qualified Domain Name (FQDN), which has to be configured along with the IP address of the PDF. There will be no name resolving for the FQDN, it will be used as it is.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  InetAddressDNS Size(1..100)  

cGgsnPdfIpAddressType 1.3.6.1.4.1.9.9.240.1.3.10.1.1.3
This object specifies the type of IP address of the PDF server.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

cGgsnPdfIpAddress 1.3.6.1.4.1.9.9.240.1.3.10.1.1.4
This object specifies the IP address of the PDF server. The type of the address is specified by the object cGgsnPdfIpAddressType.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  InetAddress  

cGgsnPdfRowStatus 1.3.6.1.4.1.9.9.240.1.3.10.1.1.5
This object is used to create a new row or delete an existing row in this table. To create a row, set this object to 'createAndGo(4)'. To delete a row, set this object to 'destroy(6)'.
Status: deprecated Access: read-create
OBJECT-TYPE    
  RowStatus  

cGgsnPdfReconnectTimeOut 1.3.6.1.4.1.9.9.240.1.3.10.1.1.6
Whenever a connection outage is detected (by keepalive mechanism etc.) by GGSN to the PDF server. The GGSN waits for the interval configured in this object. Once this timer is expired, another attempt is made for connection establishment.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Unsigned32 1..60  

cGgsnPdfReconnectRetries 1.3.6.1.4.1.9.9.240.1.3.10.1.1.7
This is the number of attempts for connection establishment after the timeout value set in cGgsnPdfReconnectTimeOut. After the configured number of retries, all the COPS sessions (and associated PDP contexts) are cleared. The value '65535' which is default, will be infinite retries.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Unsigned32 0..10 | 65535  

cGgsnPdfReconExpPdpDelete 1.3.6.1.4.1.9.9.240.1.3.10.1.1.8
This objects defines the handling of the PDP context in the connection loss scenario. When this object is set to true, then on connection loss, the PDP delete will be initiated.
Status: deprecated Access: read-create
OBJECT-TYPE    
  TruthValue  

cGgsnPdfReqRetryTimeOut 1.3.6.1.4.1.9.9.240.1.3.10.1.1.9
For each COPS REQ sent to PDF, GGSN will start a request retry timer with this value. If DEC is not received within the timeout, the REQ is resent for cGgsnPdfReqRetries times.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Unsigned32 1..60  

cGgsnPdfReqRetries 1.3.6.1.4.1.9.9.240.1.3.10.1.1.10
This is the number of retries which has to be sent for the COPS REQ being sent. If DEC is not received even after sending the COPS REQ for configured number of retries, the PDP context activation/modification (which had triggered this REQ) is rejected.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Unsigned32 0..10  

cGgsnPcscfTable 1.3.6.1.4.1.9.9.240.1.3.10.2
This table contains the entries of P-CSCF groups with the addresses configured. One or more IP address can be configured per group name. This group in turn will be mapped to the APN. P-CSCF is a network element providing session management services. When the UE request the GGSN for P-CSCF address through activate PDP Request, these addresses will be returned to the UE in the order which they are configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CGgsnPcscfEntry

cGgsnPcscfEntry 1.3.6.1.4.1.9.9.240.1.3.10.2.1
An entry is created when the user configures the group name and an IP address is set.
Status: current Access: not-accessible
OBJECT-TYPE    
  CGgsnPcscfEntry  

cGgsnPcscfGroupName 1.3.6.1.4.1.9.9.240.1.3.10.2.1.1
This group name is the identifier for the P-CSCF addresses configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..100)  

cGgsnPcscfIpAddressType 1.3.6.1.4.1.9.9.240.1.3.10.2.1.2
This object specifies the type of the P-CSCF IP address.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

cGgsnPcscfIpAddress 1.3.6.1.4.1.9.9.240.1.3.10.2.1.3
This object specifies the IP address of the P-CSCF. The type of this address is specified by the object cGgsnPcscfIpAddressType.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

cGgsnPcscfRowStatus 1.3.6.1.4.1.9.9.240.1.3.10.2.1.4
This object is used to create a new row or delete an existing row in this table. To create a row, set this object to 'createAndGo(4)'. To delete a row, set this object to 'destroy(6)'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cGgsnMemoryThreshold 1.3.6.1.4.1.9.9.240.1.3.11
GGSN memory overload protection is a mechanism to prevent GGSN from completely running out of memory when GGSN is running near its capacity or in some failure scenarios like CG down. A protection mechanism was put into place where charging triggers would be ignored, PDP create would be rejected, PDP update request will delete PDP, once the available memory on the GGSN drops below a configured threshold. Charging triggers occurs due to certain criteria's like volume limit, time limit. When one of the conditions is met , the CDR's are closed and will be updated to the charging gateway.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..1024  

cGgsnServiceMode 1.3.6.1.4.1.9.9.240.1.3.12
GGSN supports this GPRS service mode for maintenance purposes. Two modes are supported in GGSN, operational and maintenance mode. 'inService' mode represents nominal operation, and there will be no change in the way the GGSN operates. 'maintenance' mode imposes restrictions, such as some of the configurations allowed by the GGSN, and no new PDPs will be accepted. 'maintenance' mode can be useful to make some changes to the configuration of the GGSN without affecting the existing PDPs. 'maintenance' mode gloablly applies to the GGSN, which means the whole box will be put in maintenance mode. There also exists APN level maintenance mode, which is defined in CISCO-GPRS_ACC-PT-MIB, and charging maintenance mode which is defined in CISCO-GPRS-CHARGING-MIB, which is out of scope of this MIB. Internally GGSN maintains three states (inService, maintenance and outOfService ), which can be viewed with cGgsnServiceModeStatus. The SNMP entity generates notification when switching modes. It uses the cGgsnInServiceNotif and cGgsnMaintenanceNotif for this purpose.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER inService(1), maintenance(2)  

cGgsnPlmnTable 1.3.6.1.4.1.9.9.240.1.3.13
Mobile Country Code (MCC) and Mobile Network Code (MNC) together identify a GPRS PLMN of an operator. PLMN Ids other than home PLMNs are considered as foreign. There will be some situations where some foreign PLMNs has to be treated as trusted PLMNs. This table contains the list of PLMNs, there can be one home PLMN entry and multiple trusted PLMN entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CGgsnPlmnEntry

cGgsnPlmnEntry 1.3.6.1.4.1.9.9.240.1.3.13.1
Entry containing list of home PLMN Ids and the Trusted PLMN Ids.
Status: current Access: not-accessible
OBJECT-TYPE    
  CGgsnPlmnEntry  

cGgsnPlmnMcc 1.3.6.1.4.1.9.9.240.1.3.13.1.1
The Mobile Country Code (MCC) is part of the PLMN Id.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(3)  

cGgsnPlmnMnc 1.3.6.1.4.1.9.9.240.1.3.13.1.2
The Mobile Network Code (MNC) is part of the PLMN Id.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(2..3)  

cGgsnPlmnRowStatus 1.3.6.1.4.1.9.9.240.1.3.13.1.3
This object is used to create a new row or delete an existing row in this table. To create a row, set this object to 'createAndGo'. To delete a row, set this object to 'destroy'. To modify a row, the row needs to be deleted and created fresh with new values.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cGgsnPlmnScope 1.3.6.1.4.1.9.9.240.1.3.13.1.4
This object specifies whether the PLMN is home or trusted. Only one PLMN entry can be home
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER home(1), trusted(2)  

cGgsnSessionTimeout 1.3.6.1.4.1.9.9.240.1.3.14
This object specifies the PDP context timeout value. The PDP context will be terminated after this timer expiry. The value present in this will have meaning when the object cGgsnRadAttrSessTimeout is set to 'true' and if the attribute#27 not received from the AAA.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 30..4294967  

cGgsnThruputIntervalOne 1.3.6.1.4.1.9.9.240.1.3.15
This object and cGgsnThruputIntervalTwo specifies the interval at which the data throughput needs to be collected per APN/SGSN. Once this object is set to some valid value, the data throughput collections gets started for per configured APN and per PATH created. The data throughput collection is updated periodically (each expiry of configured throughput interval) to the corresponding objects (cGgsnSgsnStatTable for per SGSN and cgprsAccPtThruputStatsTable for per APN). When this object is set to '0', the collection for this interval get stopped and the data related to this interval is deleted from the tables (cGgsnSgsnStatTable and cgprsAccPtThruputStatsTable). INCONSISTENT value SNMP error will happen when trying to set cGgsnThruputIntervalOne and cGgsnThruputIntervalTwo with same value expect '0'. Setting the same value to the same object will reset the value / collection status for that interval.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

cGgsnThruputIntervalTwo 1.3.6.1.4.1.9.9.240.1.3.16
This object specifies the time interval TWO for collecting the throughput per APN/SGSN. This object is same as cGgsnThruputIntervalOne. It's just an option for a second throughput collection for a different throughput interval time. The value 0 means the timer TWO will be disabled. INCONSISTENT value SNMP error will happen when trying to set cGgsnThruputIntervalOne and cGgsnThruputIntervalTwo with same value expect '0'. Setting the same value to the same object will reset the value / collection status for that interval.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

cGgsnCompliance3GppGgsn 1.3.6.1.4.1.9.9.240.1.3.17
This object specifies the compliance level for the particular GGSN version present in cGgsnVersion. This object can be used to set back the compliance level to the previous GGSN version. When set to 'default', the compliance level for that GGSN version indicated by the object cGgsnVersion will be considered. Currently, when the cGgsnVersion is holding a value of 'release50', the compliance level can be set back to 'release40'. This object is deprecated as the standard GGSN 8.0 release deprecated this configuration.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER default(0), release40(1)  

cGgsnCreateReqV1UpdExistPdp 1.3.6.1.4.1.9.9.240.1.3.18
This object is used for backward compatibility due to to implementation of CR 311. CR 311: The SGSN shall not send a Create PDP Context Request for an already active context. If a new Create PDP Context Request is incoming on TEID 0 for an already active PDP context, this Create PDP Context Request must be considered related to a new session. The existing PDP context shall be torn down locally, and the associated PDP contexts deleted locally, before the new session is created. If a new Create PDP Context Request is incoming on a TEID which is different from 0 and this TEID is already allocated to one or more activated PDP contexts, and the NSAPI IE value in this message matches the NSAPI value of an active PDP context, the GGSN shall send back a Create PDP Context Response with a rejection cause code. It is implementation dependent deciding whether to teardown or keep the existing PDP context. 'false' - The changes due to CR 311 will be applicable. 'true' - The changes due to CR 311 will not be taken into account. This object has no meaning when the object cGgsnCompliance3GppGgsn holds a value of 'release40'. This object is deprecated as the standerd GGSN release 5.2 deprecated this configuration.
Status: deprecated Access: read-write
OBJECT-TYPE    
  TruthValue  

cGgsnRadAttrSessTimeout 1.3.6.1.4.1.9.9.240.1.3.19
This object is used for enabling the session timeout feature on the global (router) level set using cGgsnSessionTimeout, APN level (cgprsAccPtAbsoluteSessionTimer, which is defined in CISCO-GPRS-ACC-PT-MIB and is outside the scope of this MIB) and also parse the RADIUS attribute #27 present in the access-accept request. 'true' - Session timeout is enabled. 'false' - Session timeout is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cGgsnDownlinkVerifyMsDisable 1.3.6.1.4.1.9.9.240.1.3.20
This object enables the feature which will allow the GGSN to route IP packets beyond MS. This works only if a static route is added in GGSN to the node beyond the MS. On enabling this feature, GGSN will route the packets in both process switch path and cef switch path. This is supported only for IP PDP type. This feature has some limitations: - This is not scalable, since the operator has to add static route to all the node beyond the MS. - Only works for MS having static address. - In case of GTPv1 the MS has to select TFT's so as to allow traffic flow in the downlink direction. - IP address assignment/Radius for the devices behind the MS needs to be done within the scope of that network; the GGSN will not provide this facility in anyway for the hosts behind the MS. - In case for MWAM and Cat6500/7600 environment, the static route should be added only on that particular GGSN on the MWAM from where the MS is reachable. 'true' - Routing beyond MS is enabled. 'false' - Routing beyond MS is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cGgsnSlbMode 1.3.6.1.4.1.9.9.240.1.3.21
GTP SLB can operate in two modes-dispatched and directed. - 'dispatched' mode: It forwards the create request without changing the destination IP address (vserver address) and the create response comes from the same (vserver) address. - 'directed' mode: It changes the destination IP address to that of GGSN's VT and the create response comes from the GGSN VT.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER directed(1), dispatched(2)  

cGgsnSlbNotif 1.3.6.1.4.1.9.9.240.1.3.22
This object is used to enable or disable the GGSN behavior of sending CAC failure notification to SLB, or session failure notification to SLB. If this object is set to cacFailure(1), then this object is required to enable the feature in the dispatched mode of operation of SLB. If this object is set to sessionDeletion(2), then GGSN will send delete notification message to SLB when the last PDP associated with a IMSI is deleted. This object is deprecated by cGgsnSlbNotifyCacFailure and cGgsnSlbNotifySessionDeletion.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER cacFailure(1), sessionDeletion(2)  

cGgsnSlbVserverTable 1.3.6.1.4.1.9.9.240.1.3.23
This table includes the different virtual servers (IP address of virtual servers) and the elements gives the interface to reach these servers. The table is indexed on the vserver address. The table objects can be modified, when the RowStatus (cGgsnSlbVserRowStatus) is active.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CGgsnSlbVserverEntry

cGgsnSlbVserverEntry 1.3.6.1.4.1.9.9.240.1.3.23.1
Entry contains the Virtual server details(IP address type, IP address)and next hop address and VRF name.
Status: current Access: not-accessible
OBJECT-TYPE    
  CGgsnSlbVserverEntry  

cGgsnSlbVserAddrType 1.3.6.1.4.1.9.9.240.1.3.23.1.1
This object specifies the address type of the vserver.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

cGgsnSlbVserAddress 1.3.6.1.4.1.9.9.240.1.3.23.1.2
This object specifies the address of GTP vservers. It is required only in directed mode. If SLB is running in directed mode and this object is not configured, then the feature remains disabled. If SLB is running in the dispatched mode, the vserver that forwarded the create request is known to the GGSN and thus it is possible to send the notification directly to the vserver.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4..20)  

cGgsnSlbVserNextHopAddrType 1.3.6.1.4.1.9.9.240.1.3.23.1.3
This object specifies the IP address type to reach the virtual server.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

cGgsnSlbVserNextHopAddress 1.3.6.1.4.1.9.9.240.1.3.23.1.4
This object specifies the IP address to reach the vserver.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress Size(4..20)  

cGgsnSlbVserVrfName 1.3.6.1.4.1.9.9.240.1.3.23.1.5
This object specifies the VRF name on an interface on GGSN connected to SLB, to reach the vserver.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

cGgsnSlbVserRowStatus 1.3.6.1.4.1.9.9.240.1.3.23.1.6
This object will create new row into the table or deletes the existing one. To create a row, set this object to 'createAndGo(4)'. To delete a row, set this object to 'destroy(6)'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cGgsnSlbNotifyCacFailure 1.3.6.1.4.1.9.9.240.1.3.24
This object is used to enable or disable the GGSN behavior of sending CAC failure notification to SLB. CAC fails on GGSN if either the maximum number of PDPs reaches limit or there is not enough bandwidth for the traffic class for the APN. If this object is set to 'true', GGSN sends the notification to all the SLB vservers when UMTS CAC fails.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cGgsnSlbNotifySessionDeletion 1.3.6.1.4.1.9.9.240.1.3.25
This object is used to enable or disable the GGSN behavior of sending session deletion notification to SLB. If this object is set to 'true', GGSN sends delete notification message to SLB when the last PDP associated with a IMSI is deleted.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cGgsnVersion 1.3.6.1.4.1.9.9.240.1.4.1
This object specifies the which release of GPRS image is currently running on the GGSN.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER release14(1), release30(2), release40(3), release31(4), release50(5), release60(6), release70(7), release80(8), release90(9), release100(10)  

cGgsnActiveNetworkInitPdps 1.3.6.1.4.1.9.9.240.1.4.2
This object represents the number of network initiated PDP contexts that are currently active. Trigger Condition: This counter is incremented / decremented by the create/delete PDP context request message respectively.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnActivePppPdps 1.3.6.1.4.1.9.9.240.1.4.3
This object represents the number of PPP PDP contexts that are currently active. Trigger Condition: This counter is incremented / decremented by the create/delete PPP PDP context request message respectively.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnActivePppRegenPdps 1.3.6.1.4.1.9.9.240.1.4.4
This object represents the number of PPP-Regen PDP contexts that are currently active. Trigger Condition: This counter is incremented / decremented by the create/delete PPP Regeneration PDP context request message respectively.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnPendingPppRegenPdps 1.3.6.1.4.1.9.9.240.1.4.5
This object represents the current number of pending PPP regeneration sessions. Trigger Condition: This counter is triggered by the create PPP Regeneration PDP context request message.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnActiveGtpVersion0Pdps 1.3.6.1.4.1.9.9.240.1.4.6
This object represents the current number of active GTP v0 PDP contexts. Trigger Condition: This counter is incremented / decremented by the create/delete PDP context request message respectively.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnActiveGtpVersion1Pdps 1.3.6.1.4.1.9.9.240.1.4.7
This object represents the current number of active GTP v1 PDP contexts. Trigger Condition: This counter is incremented / decremented by the create/delete PDP context request message respectively.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnGtpEncapInterface 1.3.6.1.4.1.9.9.240.1.4.8
This object represents the ifIndex of the interface on which gtp encapsulation is configured. Only one interface can be configured with gtp encapsulation on the GGSN. A zero value indicates that no interface is configured with gtp encapsulation.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

cGgsnServiceModeStatus 1.3.6.1.4.1.9.9.240.1.4.9
This object represents the internal service mode which GGSN maintains. The service switching is done with object cGgsnServiceMode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inService(1), maintenance(2), outOfServiceInProgress(3), outOfService(4)  

cGgsnConfigVersion 1.3.6.1.4.1.9.9.240.1.4.10
This object specifies the config version of GPRS image. The value of this object will be of the form Version.Release.Maintenence. This object provides information on the ability of the devices to support configuration operations.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

cGgsnPrepaidPDPs 1.3.6.1.4.1.9.9.240.1.4.11
This object specifies the number of prepaid PDPs created since the last clearance of statistics (GPRS service aware statistics).
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnPostpaidPDPs 1.3.6.1.4.1.9.9.240.1.4.12
This object specifies the current number of postpaid PDPs, created since the last clearance of statistics (GPRS service aware statistics).
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnActivatedIpv6Gtpv0Pdp 1.3.6.1.4.1.9.9.240.1.4.13
This object represents the current number of active GTP v0 ipv6 PDP contexts. Trigger Condition: This counter is incremented by the create PDP context request and decremented by the delete PDP context request message.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnActivatedIpv6Gtpv1Pdp 1.3.6.1.4.1.9.9.240.1.4.14
This object represents the current number of active GTP v1 ipv6 PDP contexts. Trigger Condition: This counter is incremented by the create PDP context request and decremented by the delete PDP context request message.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnActivatedIpv6Ms 1.3.6.1.4.1.9.9.240.1.4.15
This object represents the current number of MS with active IPv6 PDPs.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cGgsnGtpEncapsuTable 1.3.6.1.4.1.9.9.240.1.4.16
This table contains information about ifIndex of the interfaces on which gtp encapsulation is configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CGgsnGtpEncapsuEntry

cGgsnGtpEncapsuEntry 1.3.6.1.4.1.9.9.240.1.4.16.1
The cGgsnGtpEncapsuEntry represents the ifIndex of the interface on which gtp encapsulation is configured. Only one interface can be configured with gtp encapsulation on the GGSN. Entry in the table created whenever interface is configured with gtp encapsulation, Entry is deleted whenever unconfiguring the gtp encapsulation from the interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  CGgsnGtpEncapsuEntry  

cGgsnGtpEncapsuInterface 1.3.6.1.4.1.9.9.240.1.4.16.1.1
This object represents the ifIndex of the interface on which gtp encapsulation is configured. Only one interface can be configured with gtp encapsulation on the GGSN. A zero value indicates that no interface is configured with gtp encapsulation.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

cGgsnPdfServerAddrType 1.3.6.1.4.1.9.9.240.1.5.1
This object specifies the type of IP address of the PDF server.
Status: deprecated Access: accessible-for-notify
OBJECT-TYPE    
  InetAddressType  

cGgsnPdfServerAddr 1.3.6.1.4.1.9.9.240.1.5.2
This object specifies the IP address of the PDF server. The type of this address is specified by the object cGgsnPdfServerAddrType.
Status: deprecated Access: accessible-for-notify
OBJECT-TYPE    
  InetAddress  

cGgsnNotifAccessPointName 1.3.6.1.4.1.9.9.240.1.5.3
This object specifies the Access Point Name and is used specify the name in the cGgsnAccessPointNameNotif notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  SnmpAdminString Size(1..100)  

cGgsnNotifPdpImsi 1.3.6.1.4.1.9.9.240.1.5.4
This object specifies the International Mobile Subscriber Identity (IMSI) of the user for whom the notification is generated. This object is used to specify IMSI of the user in the cGgsnPacketDataProtocolNotif notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  SnmpAdminString Size(1..8)  

cGgsnGlobalErrorTypes 1.3.6.1.4.1.9.9.240.1.5.5
This object indicates the types of global errors as follows. 'ggsnServiceUp' - GGSN service has started 'ggsnServiceDown' - GGSN service is shutdown 'mapSgsnUp' - MAP-SGSN service has started 'mapSgsnDown' - MAP-SGSN service is shutdown 'noDHCPServer' -- DHCP server is not configured
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER ggsnServiceUp(1), ggsnServiceDown(2), mapSgsnUp(3), mapSgsnDown(4), noDHCPServer(5)  

cGgsnAccessPointErrorTypes 1.3.6.1.4.1.9.9.240.1.5.6
This object indicates the types access point errors as follows. 'noRadius' - RADIUS Server is not configured. 'ipAllocationFail' - Unable to allocate IP address. 'apnUnreachable' - Unable to reach access point.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER noRadius(1), ipAllocationFail(2), apnUnreachable(3)  

cGgsnPacketDataProtoErrorTypes 1.3.6.1.4.1.9.9.240.1.5.7
This object indicates the types of Packet Data Protocol errors as follows. 'noResource' - Mobile Station initiated PDP count reaches the specified limit or Network initiated PDP count reaches the specified limit. 'authenticationFail' - Authentication failed. 'ccrInitFail' - CCR(initial)is sent to diameter server, and Tx timer expires before getting CCA (initial) response. The action on the PDP context creation is determined by the configured failure handling, as specified in cGgsnSADccaCcfh object in CISCO-GGSN-SERVICE-AWARE-MIB. 'quotaPushFail' - Quota Push failed, when the path between CSG-QS is down or when CSG sends a negative Response for quota push request.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER noResource(1), authenticationFail(2), ccrInitFail(3), quotaPushFail(4)  

cGgsnNotifPdpMsisdn 1.3.6.1.4.1.9.9.240.1.5.8
This object specifies the Mobile Subscriber ISDN (MSISDN) value of the user for whom the notification is generated. This object is used to specify MSISDN of the user in the cGgsnPacketDataProtocolNotif notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  SnmpAdminString  

cGgsnNotifPrefix 1.3.6.1.4.1.9.9.240.2
OBJECT IDENTIFIER    

cGgsnNotifications 1.3.6.1.4.1.9.9.240.2.0
OBJECT IDENTIFIER    

cGgsnNotification 1.3.6.1.4.1.9.9.240.2.0.1
This notification indicates the occurrence of a GGSN related alarm. If and when additional useful information is available for specific types of alarms, then that information may be appended to the end of the notification in additional varbinds.
Status: deprecated Access: accessible-for-notify
NOTIFICATION-TYPE    

cGgsnInServiceNotif 1.3.6.1.4.1.9.9.240.2.0.2
A notification of this type is generated when GGSN is placed in inService mode which is specified by cGgsnServiceModeStatus.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

cGgsnMaintenanceNotif 1.3.6.1.4.1.9.9.240.2.0.3
A notification of this type is generated when GGSN is placed in maintenance mode which is specified by cGgsnServiceModeStatus.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

cGgsnMemThresholdReachedNotif 1.3.6.1.4.1.9.9.240.2.0.4
A notification of this type is generated when GGSN reaches the memory threshold value specified by cGgsnMemoryThreshold.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

cGgsnMemThresholdClearedNotif 1.3.6.1.4.1.9.9.240.2.0.5
A notification of this type is generated when GGSN retains the memory and falls below threshold value speficied by cGgsnMemoryThreshold.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

cGgsnPdfStateUpNotif 1.3.6.1.4.1.9.9.240.2.0.6
A notification of this type is generated when PDF connection comes UP.
Status: deprecated Access: accessible-for-notify
NOTIFICATION-TYPE    

cGgsnPdfStateDownNotif 1.3.6.1.4.1.9.9.240.2.0.7
A notification of this type is generated when PDF connection goes DOWN.
Status: deprecated Access: accessible-for-notify
NOTIFICATION-TYPE    

cGgsnGlobalErrorNotif 1.3.6.1.4.1.9.9.240.2.0.8
This notification indicates the occurrence of a GGSN related alarm.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

cGgsnAccessPointNameNotif 1.3.6.1.4.1.9.9.240.2.0.9
This notification indicates the occurrence of a APN related alarm.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

cGgsnPacketDataProtocolNotif 1.3.6.1.4.1.9.9.240.2.0.10
This notification indicates the occurrence of a User related alarm.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

cGgsnMIBConformances 1.3.6.1.4.1.9.9.240.3
OBJECT IDENTIFIER    

cGgsnMIBCompliances 1.3.6.1.4.1.9.9.240.3.1
OBJECT IDENTIFIER    

cGgsnMIBGroups 1.3.6.1.4.1.9.9.240.3.2
OBJECT IDENTIFIER    

cGgsnMIBCompliance 1.3.6.1.4.1.9.9.240.3.1.1
The compliance statements for entities which implement the CISCO GGSN MIB. This is deprecated by cGgsnMIBComplianceRev1.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

cGgsnMIBComplianceRev1 1.3.6.1.4.1.9.9.240.3.1.2
The compliance statements for entities which implement the CISCO GGSN MIB. This is deprecated by cGgsnMIBComplianceRev2
Status: deprecated Access: accessible-for-notify
MODULE-COMPLIANCE    

cGgsnMIBComplianceRev2 1.3.6.1.4.1.9.9.240.3.1.3
The compliance statements for entities which implement the CISCO GGSN MIB.
Status: deprecated Access: accessible-for-notify
MODULE-COMPLIANCE    

cGgsnMIBComplianceRev3 1.3.6.1.4.1.9.9.240.3.1.4
The compliance statements for entities which implement the CISCO GGSN MIB. This is deprecated by cGgsnMIBComplianceRev4.
Status: deprecated Access: accessible-for-notify
MODULE-COMPLIANCE    

cGgsnMIBComplianceRev4 1.3.6.1.4.1.9.9.240.3.1.5
The compliance statements for entities which implement the CISCO GGSN MIB. This is deprecated by cGgsnMIBComplianceRev5.
Status: deprecated Access: accessible-for-notify
MODULE-COMPLIANCE    

cGgsnMIBComplianceRev5 1.3.6.1.4.1.9.9.240.3.1.6
The compliance statements for entities which implement the CISCO GGSN MIB. This is deprecated by cGgsnMIBComplianceRev6.
Status: deprecated Access: accessible-for-notify
MODULE-COMPLIANCE    

cGgsnMIBComplianceRev6 1.3.6.1.4.1.9.9.240.3.1.7
The compliance statements for entities which implement the CISCO GGSN MIB.
Status: deprecated Access: accessible-for-notify
MODULE-COMPLIANCE    

cGgsnMIBComplianceRev7 1.3.6.1.4.1.9.9.240.3.1.8
The compliance statements for entities which implement the CISCO GGSN MIB. This is deprecated by cGgsnMIBComplianceRev8.
Status: deprecated Access: accessible-for-notify
MODULE-COMPLIANCE    

cGgsnMIBComplianceRev8 1.3.6.1.4.1.9.9.240.3.1.9
The compliance statements for entities which implement the CISCO GGSN MIB.This is deprecated by cGgsnMIBComplianceRev9.
Status: deprecated Access: accessible-for-notify
MODULE-COMPLIANCE    

cGgsnMIBComplianceRev9 1.3.6.1.4.1.9.9.240.3.1.10
The compliance statements for entities which implement the CISCO GGSN MIB.This is deprecated by cGgsnMIBComplianceRev10.
Status: deprecated Access: accessible-for-notify
MODULE-COMPLIANCE    

cGgsnMIBComplianceRev10 1.3.6.1.4.1.9.9.240.3.1.11
The compliance statements for entities which implement the CISCO GGSN MIB.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

cGgsnStatisticsGroup 1.3.6.1.4.1.9.9.240.3.2.1
A collection of statistics on GGSN.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

cGgsnNotifMgmtGroup 1.3.6.1.4.1.9.9.240.3.2.2
A collection of objects related with notification management on GGSN.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

cGgsnConfigurationsGroup 1.3.6.1.4.1.9.9.240.3.2.3
A collection of objects related with configurations on GGSN. This is deprecated by cGgsnConfigurationsGroupRev1.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

cGgsnNotifGroup 1.3.6.1.4.1.9.9.240.3.2.4
A collection of notifications.
Status: deprecated Access: accessible-for-notify
NOTIFICATION-GROUP    

cGgsnStatusGroup 1.3.6.1.4.1.9.9.240.3.2.5
A collection of objects representing status on GGSN.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

cGgsnConfigurationsGroupRev1 1.3.6.1.4.1.9.9.240.3.2.6
A collection of objects related with configurations on GGSN.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

cGgsnUmtsGroup 1.3.6.1.4.1.9.9.240.3.2.7
A collection of objects pertaining to GTP v1.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

cGgsnStatisticsGroupRev1 1.3.6.1.4.1.9.9.240.3.2.8
A collection of statistics on GGSN. This group is deprecated by cGgsnStatisticsGroupRev2.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

cGgsnNotifGroupRev1 1.3.6.1.4.1.9.9.240.3.2.9
A collection of notifications.
Status: deprecated Access: accessible-for-notify
NOTIFICATION-GROUP    

cGgsnConfigurationsGroupRev2 1.3.6.1.4.1.9.9.240.3.2.10
A collection of objects related with configurations on GGSN. This object group is superceded by cGgsnConfigurationsGroupRev3.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

cGgsnStatusGroupRev1 1.3.6.1.4.1.9.9.240.3.2.11
A collection of objects representing status on GGSN.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

cGgsnNotifInfoGroup 1.3.6.1.4.1.9.9.240.3.2.12
A collection of objects representing Notif Info on GGSN.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

cGgsnNotifGroupRev2 1.3.6.1.4.1.9.9.240.3.2.13
A collection of notifications. This object group is superceded by cGgsnNotifGroupRev3.
Status: deprecated Access: accessible-for-notify
NOTIFICATION-GROUP    

cGgsnNotifInfoGroupRev1 1.3.6.1.4.1.9.9.240.3.2.14
A collection of objects representing Notif Info on GGSN. This object group is superceded by cGgsnNotifInfoGroupRev2.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

cGgsnNotifMgmtGroupRev1 1.3.6.1.4.1.9.9.240.3.2.15
A collection of objects related with notification management on GGSN. This object group is superceded by cGgsnNotifMgmtGroupRev2.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

cGgsnStatusGroupConfigVer 1.3.6.1.4.1.9.9.240.3.2.16
A collection of objects representing config version of GGSN.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

cGgsnConfigurationsGroupR60 1.3.6.1.4.1.9.9.240.3.2.17
A collection of objects representing configurations on GGSN. This group is deprecated by cGgsnConfigurationsGroupR60Rev1.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

cGgsnStatisticsGroupR60 1.3.6.1.4.1.9.9.240.3.2.18
A collection of objects related with statistics.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

cGgsnStatusGroupR60 1.3.6.1.4.1.9.9.240.3.2.19
A collection of objects related to gtp status.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

cGgsnNotifInfoGroupR60 1.3.6.1.4.1.9.9.240.3.2.20
A collection of objects representing the Notif info on GGSN.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

cGgsnConfigurationsGroupR60Rev1 1.3.6.1.4.1.9.9.240.3.2.21
A collection of objects representing configurations on GGSN.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

cGgsnStatisticsGroupRev2 1.3.6.1.4.1.9.9.240.3.2.22
A collection of objects related with statistics.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

cGgsnStatusGroupR70 1.3.6.1.4.1.9.9.240.3.2.23
A collection of objects related with status.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

cGgsnConfigurationsGroupRev3 1.3.6.1.4.1.9.9.240.3.2.24
A collection of objects related with configurations on GGSN. This is deprecated by cGgsnConfigurationsGroupRev4.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

cGgsnNotifMgmtGroupRev2 1.3.6.1.4.1.9.9.240.3.2.25
A collection of objects related with notification management on GGSN.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

cGgsnNotifGroupRev3 1.3.6.1.4.1.9.9.240.3.2.26
A collection of notifications.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

cGgsnNotifInfoGroupRev2 1.3.6.1.4.1.9.9.240.3.2.27
A collection of objects representing Notif Info on GGSN.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

cGgsnConfigurationsGroupRev4 1.3.6.1.4.1.9.9.240.3.2.28
A collection of objects related with configurations on GGSN.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

cGgsnStatusGroupR90 1.3.6.1.4.1.9.9.240.3.2.29
A collection of objects which maintains the mapping between CGSN interfaces and gtp encapsulated interfaces.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

cGgsnConfigurationsGroupSup1 1.3.6.1.4.1.9.9.240.3.2.30
This group is supplementary to cGgsnConfigurationsGroupRev4.
Status: current Access: accessible-for-notify
OBJECT-GROUP