CISCO-CAS-IF-MIB

File: CISCO-CAS-IF-MIB.mib (95702 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB CISCO-TC CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
RowStatus TruthValue DisplayString
MODULE-COMPLIANCE OBJECT-GROUP InterfaceIndex
ifIndex CountryCode ciscoMgmt

Defined Types

CcasDs1IfCfgEntry  
SEQUENCE    
  ccasDs1IfCfgDs0ChannelsConfigurable OCTET STRING

CcasGrpCfgEntry  
SEQUENCE    
  ccasGrpCfgIndex Integer32
  ccasGrpCfgType INTEGER
  ccasGrpCfgDs0Channels OCTET STRING
  ccasGrpCfgServiceType INTEGER
  ccasGrpCfgRowStatus RowStatus

CcasGrpEMCfgEntry  
SEQUENCE    
  ccasGrpEMCfgDialType INTEGER
  ccasGrpEMCfgDnisAni BITS
  ccasGrpEMCfgLmrMCap INTEGER
  ccasGrpEMCfgLmrECap INTEGER
  ccasGrpEMCfgAutoGainControl TruthValue

CcasGrpEMTmEntry  
SEQUENCE    
  ccasGrpEMTmClearWaitDuration Integer32
  ccasGrpEMTmMaxWinkWaitDuration Integer32
  ccasGrpEMTmMaxWinkDuration Integer32
  ccasGrpEMTmDelayStart Integer32
  ccasGrpEMTmMaxDelayDuration Integer32
  ccasGrpEMTmMinDelayPulseWidth Integer32
  ccasGrpEMTmDigitDuration Integer32
  ccasGrpEMTmInterDigitDuration Integer32
  ccasGrpEMTmPulseRate Integer32
  ccasGrpEMTmPulseInterDigitDuration Integer32
  ccasGrpEMTmVoiceHangover Integer32
  ccasGrpEMTmLmrTeardown Integer32
  ccasGrpEMTmPttXmt Integer32
  ccasGrpEMTmPttRcv Integer32
  ccasGrpEMTmDelayVoice Integer32

CcasGrpLineCfgEntry  
SEQUENCE    
  ccasGrpLineCfgNumberRings Integer32
  ccasGrpLineCfgSupDisconnect TruthValue
  ccasGrpLineCfgDialType INTEGER

CcasGrpLineTmEntry  
SEQUENCE    
  ccasGrpLineTmDigitDuration Integer32
  ccasGrpLineTmInterDigitDuration Integer32
  ccasGrpLineTmPulseRate Integer32
  ccasGrpLineTmPulseInterDigitDuration Integer32

CcasGrpStaCfgEntry  
SEQUENCE    
  ccasGrpStaCfgNumberRings Integer32
  ccasGrpStaCfgDialType INTEGER

CcasGrpStaTmEntry  
SEQUENCE    
  ccasGrpStaTmDigitDuration Integer32
  ccasGrpStaTmInterDigitDuration Integer32
  ccasGrpStaTmPulseRate Integer32
  ccasGrpStaTmPulseInterDigitDuration Integer32

CcasGrpABCDCfgEntry  
SEQUENCE    
  ccasGrpABCDCfgInvertBits BITS
  ccasGrpABCDCfgUnusedBits BITS

CcasChannelCfgEntry  
SEQUENCE    
  ccasChannelCfgDS1IfIndex InterfaceIndex
  ccasChannelCfgGroup Integer32
  ccasChannelCfgTimeSlot Integer32
  ccasChannelCfgBusyOut TruthValue

CcasChannelStatusEntry  
SEQUENCE    
  ccasChannelStatusRecvSignalBits BITS
  ccasChannelStatusBusyOut TruthValue
  ccasChannelStatusInfoType INTEGER
  ccasChannelStatusXmitSignalBits BITS

CcasVoiceCfgEntry  
SEQUENCE    
  ccasVoiceCfgNoiseRegEnable TruthValue
  ccasVoiceCfgNonLinearProcEnable TruthValue
  ccasVoiceCfgMusicOnHoldThreshold Integer32
  ccasVoiceCfgInGain Integer32
  ccasVoiceCfgOutAttn Integer32
  ccasVoiceCfgEchoCancelEnable TruthValue
  ccasVoiceCfgEchoCancelCoverage INTEGER
  ccasVoiceCfgConnectionMode INTEGER
  ccasVoiceCfgConnectionNumber DisplayString
  ccasVoiceCfgInitialDigitTimeOut Integer32
  ccasVoiceCfgInterDigitTimeOut Integer32
  ccasVoiceCfgRegionalTone CountryCode

CcasXgcpCfgEntry  
SEQUENCE    
  ccasXgcpCfgCotToneCo1 Integer32
  ccasXgcpCfgCotToneCo2 Integer32

Defined Values

ciscoCasIfMIB 1.3.6.1.4.1.9.9.85
Channel Associated Signal Interface MIB module. This MIB manages the generic CAS (Channel Associated Signal)or DS0 clear channel Interfaces in the router.
MODULE-IDENTITY    

ccasIfObjects 1.3.6.1.4.1.9.9.85.1
OBJECT IDENTIFIER    

ccasDS1Objects 1.3.6.1.4.1.9.9.85.1.1
OBJECT IDENTIFIER    

ccasGrpObjects 1.3.6.1.4.1.9.9.85.1.2
OBJECT IDENTIFIER    

ccasChannelObjects 1.3.6.1.4.1.9.9.85.1.3
OBJECT IDENTIFIER    

ccasVoiceCfgObjects 1.3.6.1.4.1.9.9.85.1.4
OBJECT IDENTIFIER    

ccasXgcpCfgObjects 1.3.6.1.4.1.9.9.85.1.5
OBJECT IDENTIFIER    

ccasGrpGeneralObjects 1.3.6.1.4.1.9.9.85.1.2.1
OBJECT IDENTIFIER    

ccasGrpEMObjects 1.3.6.1.4.1.9.9.85.1.2.2
OBJECT IDENTIFIER    

ccasGrpLineObjects 1.3.6.1.4.1.9.9.85.1.2.3
OBJECT IDENTIFIER    

ccasGrpStaObjects 1.3.6.1.4.1.9.9.85.1.2.4
OBJECT IDENTIFIER    

ccasGrpABCDObjects 1.3.6.1.4.1.9.9.85.1.2.5
OBJECT IDENTIFIER    

ccasDs1IfCfgTable 1.3.6.1.4.1.9.9.85.1.1.1
The CAS/DS0 General Configuration Table for T1/E1. It contains the CAS/DS0 related standard configuration information for T1/E1.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcasDs1IfCfgEntry

ccasDs1IfCfgEntry 1.3.6.1.4.1.9.9.85.1.1.1.1
An entry in the configuration table for each T1/E1. The entry is created when a T1/E1 hardware is detected.
Status: current Access: not-accessible
OBJECT-TYPE    
  CcasDs1IfCfgEntry  

ccasDs1IfCfgDs0ChannelsConfigurable 1.3.6.1.4.1.9.9.85.1.1.1.1.1
This object contains the bit map of the available DS0 channel in the DS1. The MSB (most significant bit) is DS0 channel number 1. The missing bytes is default to a value of 0. A 1-bit indicates the channel is available for configuration and a 0-bit indicates it isn't. The length of this object is either 3 octets (for T1) or 4 octets (for E1). The most significant bit is transmitted first.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..4)  

ccasGrpCfgTable 1.3.6.1.4.1.9.9.85.1.2.1.1
The CAS/DS0 Group Standard Configuration Table. It contains the general configuration information for the CAS/DS0 group of T1/E1 interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcasGrpCfgEntry

ccasGrpCfgEntry 1.3.6.1.4.1.9.9.85.1.2.1.1.1
A CAS/DS0 group entry. Each entry consists of the CAS group type and the CAS/DS0 group associated DS0 channels in a T1/E1. The value of ccasGrpCfgDs0Channels must be specified with at least one available DS0 channel in the CAS group associated T1/E1 before a new row in this table can become active(1). The entry of this table can only be created if the CAS/DS0 group associated DS1 ifEntry already exists.
Status: current Access: not-accessible
OBJECT-TYPE    
  CcasGrpCfgEntry  

ccasGrpCfgIndex 1.3.6.1.4.1.9.9.85.1.2.1.1.1.1
An arbitrary index that uniquely identifies a DS0 group in a T1/E1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..30  

ccasGrpCfgType 1.3.6.1.4.1.9.9.85.1.2.1.1.1.2
The Signaling type of the DS0 group. emWinkStart - CAS E&M Wink Start. emWinkStartFgd - CAS E&M Wink Start with Feature group D. emImmedStart - CAS E&M Immediate Start. emDelayDial - CAS E&M Delay Dial. fxsLoopStart - CAS FXS Loop Start. fxsGroundStart - CAS FXS Ground Start. sasLoopStart - CAS SAS Loop Start. sasGroundStart - CAS SAS Ground Start. r2Analog - R2 ITU Q411. r2Digital - R2 ITU Q421. r2Pulse - R2 ITU Supplement 7. p7 - P7 switch. fgdOS - Bellcore Feature Group D : Operator Services Signaling nullSignaling - 64k clear channel r1Itu - R1 ITU. r1Modified - R1 Modified. r1Turkey - R1 Turkey. fgdEANA - FGD Exchange Access North American. emMelImmedStart - CAS E&M Melcas Immediate Start emMelWink - CAS E&M Melcas Wink Start emMelDelayDial - CAS E&M Melcas Delay Dial fxsMelcas - CAS FXS Melcas fxoMelcas - CAS FXO Melcas extsig - External Signal emLmr - CAS E&M Land Mobil Radio(LMR) interface
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER emWinkStart(1), emWinkStartFgd(2), emImmedStart(3), emDelayDial(4), fxsLoopStart(5), fxsGroundStart(6), sasLoopStart(7), sasGroundStart(8), r2Analog(9), r2Digital(10), r2Pulse(11), p7(12), fxoLoopStart(13), fxoGroundStart(14), fgdOS(15), nullSignaling(16), r1Itu(17), r1Modified(18), r1Turkey(19), fgdEANA(20), emMelImmedStart(21), emMelWink(22), emMelDelayDial(23), fxsMelcas(24), fxoMelcas(25), extsig(26), emLmr(27)  

ccasGrpCfgDs0Channels 1.3.6.1.4.1.9.9.85.1.2.1.1.1.3
This object contains the bit map of the selected DS0 channels to be added into this group. The MSB (most significant bit) is DS0 channel number 1. For T1, only higher 24 bits are used to specify the the CAS channels for the CAS group. A 1-bit indicates the channel to be added into group and a 0-bit indicates it isn't.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(4)  

ccasGrpCfgServiceType 1.3.6.1.4.1.9.9.85.1.2.1.1.1.5
Specify the Service type of the CAS/DS0 group. none - no service type casServSw56 - sw56 service for CAS casServModme - modem service for CAS casServAuto - auto service for CAS sgcp - Simple Gateway Control Protocol (SGCP) service. Used when DS0 is configured for null signaling. mgcp - Media Gateway Control Protocol (MGCP) service. Used when DS0 is configured for null signaling. other - none of the above and the below. trunkingService - This DS0 group is handled by trunking service application. h248 - ITU H.248 Media Gateway Control service. Used when DS0 is configured for null signaling. ds0xconn - Used for DS0 cross connection. xgcp - Media Gateway Control Protocol (MGCP) extension service including TGCP (Trunking Gateway Control Protocol) profiles feature. Used when DS0 is configured for null signaling.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), casServSw56(2), casServModem(3), casServAuto(4), sgcp(5), mgcp(6), other(7), trunkingService(8), h248(9), ds0xconn(10), xgcp(11)  

ccasGrpCfgRowStatus 1.3.6.1.4.1.9.9.85.1.2.1.1.1.4
This object is used to create a new row or modify or delete an existing row in this table. The corresponding instance of ccasGrpCfgType can not be modified while this object has the value 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ccasGrpEMCfgTable 1.3.6.1.4.1.9.9.85.1.2.2.1
The CAS Group E&M Standard Configuration Table. It contains the CAS E&M group standard configuration information of T1/E1.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcasGrpEMCfgEntry

ccasGrpEMCfgEntry 1.3.6.1.4.1.9.9.85.1.2.2.1.1
An entry in the configuration table for each CAS E&M Group in the T1/E1. The entry is created when the ccasGrpCfgType is configured as 'em' on a T1/E1 via configuration command. The entry is deleted when the CAS Group is de-configured from T1/E1.
Status: current Access: not-accessible
OBJECT-TYPE    
  CcasGrpEMCfgEntry  

ccasGrpEMCfgDialType 1.3.6.1.4.1.9.9.85.1.2.2.1.1.1
Specify the addressing type of the CAS group. dtmf - Dual Tone Multi-Frequency (DTMF) digit. pulse - dial pulse. mf - Multi-Frequency (MF) digit. The default value of this object is dtmf(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dtmf(1), pulse(2), mf(3)  

ccasGrpEMCfgDnisAni 1.3.6.1.4.1.9.9.85.1.2.2.1.1.2
Specify the type of Destination Number Identification Service (DNIS) and Automatic Number Identification (ANI) support. MF tone supports both ANI and DNIS services. The DTMF tone only supports both incoming and outgoing DNIS. incomingDnis - support incoming DNIS feature. incomingAni - support incoming ANI feature. outgoingDnis - support outgoing DNIS feature. outgoingAni - support outgoing ANI feature. The default value of this object is '00'H.
Status: current Access: read-write
OBJECT-TYPE    
  BITS incomingDnis(0), incomingAni(1), outgoingDnis(2), outgoingAni(3)  

ccasGrpEMCfgLmrMCap 1.3.6.1.4.1.9.9.85.1.2.2.1.1.3
The M lead behavior of E&M LMR interface. inact - The m-lead status should be ignored. audio - The m-lead status is used to control generating voice packet. dial - The first m-lead off to on status indicates call setup request. The following m-lead status change during the call should be ignored.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER inact(1), audio(2), dial(3)  

ccasGrpEMCfgLmrECap 1.3.6.1.4.1.9.9.85.1.2.2.1.1.4
The E lead behavior of E&M LMR interface. seize - The e-lead used as seize signal. voice - The e-lead status is used to indicate voice packet received or not. inactive -- e-lead is inactive.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER seize(4), voice(5), inactive(6)  

ccasGrpEMCfgAutoGainControl 1.3.6.1.4.1.9.9.85.1.2.2.1.1.5
This object is used to enabling or disabling automatic gain control on this interface. AGC allows dsp to adjust the input voice volume and avoid rapid voice volume change.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ccasGrpEMTmTable 1.3.6.1.4.1.9.9.85.1.2.2.2
The E&M interface Timing Parameters table. It contains the configuration of the various E&M signaling protocol timing parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcasGrpEMTmEntry

ccasGrpEMTmEntry 1.3.6.1.4.1.9.9.85.1.2.2.2.1
An entry in the E&M Timing Parameters Table for each E&M interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  CcasGrpEMTmEntry  

ccasGrpEMTmClearWaitDuration 1.3.6.1.4.1.9.9.85.1.2.2.2.1.1
Time of Inactive incoming seizure signal to declare call cleared. This object is relevant to the interfaces in the CAS group if the ccasGrpCfgType object is emWinkStart(1) or emWinkStartFgd(2). The default value of this object is 400 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 200..2000  

ccasGrpEMTmMaxWinkWaitDuration 1.3.6.1.4.1.9.9.85.1.2.2.2.1.2
Maximum wink wait duration for sending out wink start signaling. This object is relevant to the interfaces in the CAS group if the ccasGrpCfgType object is emWinkStart(1) or emWinkStartFgd(2). The default value of this object is 200 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..5000  

ccasGrpEMTmMaxWinkDuration 1.3.6.1.4.1.9.9.85.1.2.2.2.1.3
Maximum wink duration for sending out wink start signaling. This object is relevant to the interfaces in the CAS group if the ccasGrpCfgType object is emWinkStart(1) or emWinkStartFgd(2). The default value of this object is 200 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..3000  

ccasGrpEMTmDelayStart 1.3.6.1.4.1.9.9.85.1.2.2.2.1.4
Timing of generation of outgoing delayed start signal from detection of incoming seizure. This object is relevant to the interfaces of the CAS group if the ccasGrpCfgType object is emDelayDial(4). The default value of this object is 300 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 20..2000  

ccasGrpEMTmMaxDelayDuration 1.3.6.1.4.1.9.9.85.1.2.2.2.1.5
Maximum delay signal duration for sending out delay dial signaling. This object is relevant to the interfaces in the CAS group if the ccasGrpCfgType object is emDelayDial(4). The default value of this object is 2000 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..5000  

ccasGrpEMTmMinDelayPulseWidth 1.3.6.1.4.1.9.9.85.1.2.2.2.1.6
Minimum delay-dial pulse duration for incoming call. If the value of this object is 0, then no delay-dial is sent to the far end for the incoming call. This object is relevant to the interfaces in the CAS group if the ccasGrpCfgType object is emDelayDial(4). The default value of this object is 140 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 140..5000  

ccasGrpEMTmDigitDuration 1.3.6.1.4.1.9.9.85.1.2.2.2.1.7
Outgoing DTMF/MF digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpCfgDialType is dtmf or R2 tone. The default value of this object is 100 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 50..500  

ccasGrpEMTmInterDigitDuration 1.3.6.1.4.1.9.9.85.1.2.2.2.1.8
Outgoing DTMF/MF inter-digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpCfgDialType is dtmf or R2 tone. The default value of this object is 100 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 50..500  

ccasGrpEMTmPulseRate 1.3.6.1.4.1.9.9.85.1.2.2.2.1.9
Outgoing Pulse dialing rate in pulses per second (pps). This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpCfgDialType is pulse. The default value of this object is 10 pps.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..20  

ccasGrpEMTmPulseInterDigitDuration 1.3.6.1.4.1.9.9.85.1.2.2.2.1.10
Outgoing Pulse dialing inter-digit timing in milliseconds. This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpCfgDialType is pulse. The default value of this object is 500 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..1000  

ccasGrpEMTmVoiceHangover 1.3.6.1.4.1.9.9.85.1.2.2.2.1.11
The hangover time used to determine there is no more voice packet arrived. The default value of this object is 250 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10000  

ccasGrpEMTmLmrTeardown 1.3.6.1.4.1.9.9.85.1.2.2.2.1.12
LMR port tear down timeout. This object is relevant to the waiting time of teardown call on LMR port. If the value of this object is '-1', then the timeout is disable.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 5..60000  

ccasGrpEMTmPttXmt 1.3.6.1.4.1.9.9.85.1.2.2.2.1.13
This object signifies LMR port maximum transmit time. This object is relevant to how long LMR port can continue transmit voice packet without pause.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..30  

ccasGrpEMTmPttRcv 1.3.6.1.4.1.9.9.85.1.2.2.2.1.14
This object signifies LMR port maximum receive time. This object is relevant to how long LMR port can continue receive voice packet without pause.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..30  

ccasGrpEMTmDelayVoice 1.3.6.1.4.1.9.9.85.1.2.2.2.1.15
This object is relevant to how long LMR will delay sending the voice packet to the LMR port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..1500  

ccasGrpLineCfgTable 1.3.6.1.4.1.9.9.85.1.2.3.1
The CAS Group FXS/SAS Standard Configuration Table. It contains the CAS FXS/SAS group standard configuration information of T1/E1.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcasGrpLineCfgEntry

ccasGrpLineCfgEntry 1.3.6.1.4.1.9.9.85.1.2.3.1.1
An entry in the configuration table for each CAS FXS/SAS Group in the T1/E1. The entry is created when the ccasGrpCfgType is configured as 'fxs' or 'sas' on a T1/E1 via configuration command. The entry is deleted when the CAS Group is de-configured from T1/E1.
Status: current Access: not-accessible
OBJECT-TYPE    
  CcasGrpLineCfgEntry  

ccasGrpLineCfgNumberRings 1.3.6.1.4.1.9.9.85.1.2.3.1.1.1
The number of rings detected before closing loop. If the value of this object is 0, then the managed system answers immediately after the interface detects a incoming seizure if the ccasGrpCfgType is 'fxsGroundStart' or 'sasGroundStart'. The default value of this object is 1 ring.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10  

ccasGrpLineCfgSupDisconnect 1.3.6.1.4.1.9.9.85.1.2.3.1.1.2
Specifies whether a supervisory disconnect signal will be presented to the interface when the connected party at the interface hangs up. this object is only relevant to the ccasGrpCfgType is fxsLoopStart or sasLoopStart. The default value of this object is 'true'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ccasGrpLineCfgDialType 1.3.6.1.4.1.9.9.85.1.2.3.1.1.3
Specify the addressing type of the CAS group. dtmf - Dual Tone Multi-Frequency (DTMF) digit. pulse - dial pulse. The default value of this object is dtmf(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dtmf(1), pulse(2)  

ccasGrpLineTmTable 1.3.6.1.4.1.9.9.85.1.2.3.2
The FXS/SAS interface Timing Parameters table. It contains the configuration of the various FXS/SAS signaling protocol timing parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcasGrpLineTmEntry

ccasGrpLineTmEntry 1.3.6.1.4.1.9.9.85.1.2.3.2.1
An entry in the FXS/SAS Timing Parameters Table for each FXS/SAS interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  CcasGrpLineTmEntry  

ccasGrpLineTmDigitDuration 1.3.6.1.4.1.9.9.85.1.2.3.2.1.1
Outgoing DTMF digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpLineCfgDialType is dtmf. The default value of this object is 100 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 50..500  

ccasGrpLineTmInterDigitDuration 1.3.6.1.4.1.9.9.85.1.2.3.2.1.2
Outgoing DTMF inter-digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpLineCfgDialType is dtmf. The default value of this object is 100 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 50..500  

ccasGrpLineTmPulseRate 1.3.6.1.4.1.9.9.85.1.2.3.2.1.3
Outgoing Pulse dialing rate in pulses per second (pps). This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpStaCfgDialType is pulse. The default value of this object is 10 pps.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..20  

ccasGrpLineTmPulseInterDigitDuration 1.3.6.1.4.1.9.9.85.1.2.3.2.1.4
Outgoing Pulse dialing inter-digit timing in milliseconds. This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpStaCfgDialType is pulse. The default value of this object is 500 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..1000  

ccasGrpStaCfgTable 1.3.6.1.4.1.9.9.85.1.2.4.1
The FXO/SAO standard configuration table. It contains FXO/SAO configuration parameters, one entry per FXO/SAO interface. The configuration information of this table is set by its default setting when the CAS group is created by the configuration commands.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcasGrpStaCfgEntry

ccasGrpStaCfgEntry 1.3.6.1.4.1.9.9.85.1.2.4.1.1
An entry in the standard configuration table for each FXO/SAO Group. The entry is created when the ccasGrpCfgType is configured as 'fxo' or 'sao' on a T1/E1 via configuration command. The entry is deleted when the CAS Group is de-configured from T1/E1.
Status: current Access: not-accessible
OBJECT-TYPE    
  CcasGrpStaCfgEntry  

ccasGrpStaCfgNumberRings 1.3.6.1.4.1.9.9.85.1.2.4.1.1.1
The number of rings sent before sending reorder to the originator and releasing resources. If the value of this object is 0, then sending reorder to the originator is disabled. The default value of this object is 20 rings.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1000  

ccasGrpStaCfgDialType 1.3.6.1.4.1.9.9.85.1.2.4.1.1.2
Specify the addressing type of the CAS group. dtmf - Dual Tone Multi-Frequency (DTMF) digit. pulse - dial pulse. The default value of this object is dtmf(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dtmf(1), pulse(2)  

ccasGrpStaTmTable 1.3.6.1.4.1.9.9.85.1.2.4.2
The FXO/SAO interface Timing Parameters table. It contains the configuration of the various FXO/SAO signaling protocol timing parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcasGrpStaTmEntry

ccasGrpStaTmEntry 1.3.6.1.4.1.9.9.85.1.2.4.2.1
An entry in the FXO/SAO Timing Parameters Table for each FXO/SAO interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  CcasGrpStaTmEntry  

ccasGrpStaTmDigitDuration 1.3.6.1.4.1.9.9.85.1.2.4.2.1.1
Outgoing DTMF digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpStaCfgDialType is dtmf. The default value of this object is 100 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 50..500  

ccasGrpStaTmInterDigitDuration 1.3.6.1.4.1.9.9.85.1.2.4.2.1.2
Outgoing DTMF inter-digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpStaCfgDialType is dtmf. The default value of this object is 100 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 50..500  

ccasGrpStaTmPulseRate 1.3.6.1.4.1.9.9.85.1.2.4.2.1.3
Outgoing Pulse dialing rate in pulses per second (pps). This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpStaCfgDialType is pulse. The default value of this object is 10 pps.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..20  

ccasGrpStaTmPulseInterDigitDuration 1.3.6.1.4.1.9.9.85.1.2.4.2.1.4
Outgoing Pulse dialing inter-digit timing in milliseconds. This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpStaCfgDialType is pulse. The default value of this object is 500 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..1000  

ccasGrpABCDCfgTable 1.3.6.1.4.1.9.9.85.1.2.5.1
The CAS group custom ABCD bits configuration table for E1. It contains A/B/C/D bits handling objects, one entry per CAS group on an E1 interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcasGrpABCDCfgEntry

ccasGrpABCDCfgEntry 1.3.6.1.4.1.9.9.85.1.2.5.1.1
An entry in the custom ABCD configuration table for each CAS Group on an E1 interface. The entry is created when a CAS group is configured on a E1. The entry is deleted when the CAS Group is de-configured from E1.
Status: current Access: not-accessible
OBJECT-TYPE    
  CcasGrpABCDCfgEntry  

ccasGrpABCDCfgInvertBits 1.3.6.1.4.1.9.9.85.1.2.5.1.1.1
Specify the A/B/C/D bit mask to invert the A/B/C/D bits value before the A/B/C/D bits are sent or after the A/B/C/D bits are received. 1-bit - enable bit inversion. 0-bit - disable bit inversion. The default value of this object is '00'H.
Status: current Access: read-write
OBJECT-TYPE    
  BITS dBit(0), cBit(1), bBit(2), aBit(3)  

ccasGrpABCDCfgUnusedBits 1.3.6.1.4.1.9.9.85.1.2.5.1.1.2
Specify the Unused A/B/C/D bit values to transmit. If any A/B/C/D bit is unused, the bit values in this object will be used to transmit for the unused A/B/C/D bits. The default value of this object is '00'H
Status: current Access: read-write
OBJECT-TYPE    
  BITS dBit(0), cBit(1), bBit(2), aBit(3)  

ccasChannelCfgTable 1.3.6.1.4.1.9.9.85.1.3.1
The CAS channel Standard Configuration Table. It contains the standard configuration information of CAS channel of T1/E1.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcasChannelCfgEntry

ccasChannelCfgEntry 1.3.6.1.4.1.9.9.85.1.3.1.1
An entry in the configuration table for each CAS channel. The entry is created when a CAS channel is configured on a T1/E1 via configuration command. The entry is deleted when the CAS channel is de-configured from T1/E1.
Status: current Access: not-accessible
OBJECT-TYPE    
  CcasChannelCfgEntry  

ccasChannelCfgDS1IfIndex 1.3.6.1.4.1.9.9.85.1.3.1.1.1
the ifIndex of this CAS channel associated T1/E1.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

ccasChannelCfgGroup 1.3.6.1.4.1.9.9.85.1.3.1.1.2
The CAS channel associated CAS group number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..30  

ccasChannelCfgTimeSlot 1.3.6.1.4.1.9.9.85.1.3.1.1.3
The CAS channel associated T1/E1 timeslot.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..31  

ccasChannelCfgBusyOut 1.3.6.1.4.1.9.9.85.1.3.1.1.4
The CAS channel busyout configuration. true - the CAS channel is busied out. false - the CAS is normal. The default value for this object is 'false'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ccasChannelStatusTable 1.3.6.1.4.1.9.9.85.1.3.2
The CAS channel Status Table. It contains general information about the status of CAS channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcasChannelStatusEntry

ccasChannelStatusEntry 1.3.6.1.4.1.9.9.85.1.3.2.1
An entry in the status table for each CAS channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  CcasChannelStatusEntry  

ccasChannelStatusRecvSignalBits 1.3.6.1.4.1.9.9.85.1.3.2.1.1
The receive ABCD signaling bits for the CAS channel. aBit - the signaling bit in the 6th frame bBit - the signaling bit in the 12th frame cBit - the signaling bit in the 18th frame dBit - the signaling bit in the 24th frame the cBit and dBit are only valid for E1 or T1 interface is operating in extended superframe (ESF) mode.
Status: current Access: read-only
OBJECT-TYPE    
  BITS dBit(0), cBit(1), bBit(2), aBit(3)  

ccasChannelStatusBusyOut 1.3.6.1.4.1.9.9.85.1.3.2.1.2
The CAS channel busyout state. true - the CAS channel is busied out. false - the CAS is normal.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ccasChannelStatusInfoType 1.3.6.1.4.1.9.9.85.1.3.2.1.3
The Information Transfer Capability for the current or last call. unknown - If since system startup there has been no call on this interface, this object has a value of unknown(1). speech - refers to a non-data connection data56 - 56k data. audio31 - audio 3.1 kHz; refers to data mode connections audio7 - audio 7 kHz; refer to data mode connections; 'Unrestricted digital information with tones/ announcements'. video - as defined in Q.931 fax - Facsimile modem - V.3x modem
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), speech(2), data56(3), audio31(4), audio7(5), video(6), fax(7), modem(8)  

ccasChannelStatusXmitSignalBits 1.3.6.1.4.1.9.9.85.1.3.2.1.4
The transmit ABCD signaling bits for the CAS channel. aBit - the signaling bit in the 6th frame bBit - the signaling bit in the 12th frame cBit - the signaling bit in the 18th frame dBit - the signaling bit in the 24th frame the cBit and dBit are only valid for E1 or T1 interface is operating in extended superframe (ESF) mode.
Status: current Access: read-only
OBJECT-TYPE    
  BITS dBit(0), cBit(1), bBit(2), aBit(3)  

ccasVoiceCfgTable 1.3.6.1.4.1.9.9.85.1.4.1
The voice specific configuration Table. It contains information about the voice related configuration parameters for a CAS group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcasVoiceCfgEntry

ccasVoiceCfgEntry 1.3.6.1.4.1.9.9.85.1.4.1.1
An entry in the voice specific configuration table for each CAS/DS0 group of a DS1. The entry is created if the associated CAS/DS0 group is created and the voice hardware is detected to support the voice capability for the CAS/DS0 group in the managed system. The entry is deleted when its associated CAS/DS0 group is deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  CcasVoiceCfgEntry  

ccasVoiceCfgNoiseRegEnable 1.3.6.1.4.1.9.9.85.1.4.1.1.1
The object indicates whether or not the background noise should be played to fill silence gaps if VAD is activated. The default value of this object is 'true'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ccasVoiceCfgNonLinearProcEnable 1.3.6.1.4.1.9.9.85.1.4.1.1.2
The object indicates whether or not the Nonlinear Processing is enabled for the interface. The default value of this object is 'true'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ccasVoiceCfgMusicOnHoldThreshold 1.3.6.1.4.1.9.9.85.1.4.1.1.3
The object specifies the Music On Hold Threshold for the interface. The default value of this object is -38 dBm.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -70..-30  

ccasVoiceCfgInGain 1.3.6.1.4.1.9.9.85.1.4.1.1.4
This object contains the amount of gain inserted at the receiver side of the interface. The input gain settings only define a gain/loss relative to the 0 dB setting. The absolute loss at the 0 dB setting could be implementation dependent based on the desired network loss plan. The default value of this object is 0 dB (decibel).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -6..14  

ccasVoiceCfgOutAttn 1.3.6.1.4.1.9.9.85.1.4.1.1.5
This object contains the amount of attenuation inserted at the transmit side of the interface. The output attenuation settings only define a loss relative to the 0 dB setting. The absolute loss at the 0 dB setting could be implementation dependent based on the desired network loss plan. The default value of this object is 0 dB (decibel).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..14  

ccasVoiceCfgEchoCancelEnable 1.3.6.1.4.1.9.9.85.1.4.1.1.6
The object specifies whether or not the Echo Cancellation is enabled for the interface. The default value of this object is 'true'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ccasVoiceCfgEchoCancelCoverage 1.3.6.1.4.1.9.9.85.1.4.1.1.7
The object specifies the Echo Canceller coverage for the interface. This object is valid if the ccasVoiceCfgEchoCancelEnable object is 'true'. echoCanceller8ms - 8 milliseconds echo canceller coverage. echoCanceller16ms - 16 milliseconds echo canceller coverage. echoCanceller24ms - 24 milliseconds echo canceller coverage. echoCanceller32ms - 32 milliseconds echo canceller coverage. echoCanceller64ms - 64 milliseconds echo canceller coverage. echoCanceller128ms- 128 milliseconds echo canceller coverage. The default value of this object is echoCanceller8ms.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER echoCanceller8ms(1), echoCanceller16ms(2), echoCanceller24ms(3), echoCanceller32ms(4), echoCanceller64ms(5), echoCanceller128ms(6)  

ccasVoiceCfgConnectionMode 1.3.6.1.4.1.9.9.85.1.4.1.1.8
The object indicates the connection mode of the interface. normal - the interface acts normally to handle incoming and outgoing call. trunk - the interface acts in trunking mode. trunking mode causes two interfaces (on either the same or different routers) to be always conferenced together, and for telephony signaling to be passed transparently through the VoIP system rather than trapped and interpreted by the session application on the router(s). plar - the interface acts in PLAR (private line automatic ringdown) mode. PLAR is handled by associating a peer directly with an interface such that when the interface goes off-hook, that peer is used to setup the second call leg and conference them together without the caller having to dial any digits.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), trunk(2), plar(3)  

ccasVoiceCfgConnectionNumber 1.3.6.1.4.1.9.9.85.1.4.1.1.9
This is the E.164 phone number that is used to establish connection with trunking mode or PLAR mode. If the ccasVoiceCfgConnectionMode is 'normal', then this object will be a zero length string.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

ccasVoiceCfgInitialDigitTimeOut 1.3.6.1.4.1.9.9.85.1.4.1.1.10
This is the initial digit timeout that indicates the amount of time the managed system waits for an initial input digit from the caller. The timer is activated when the call is accepted and is deactivated upon digit input. If the timer expires, the caller is signaled through the appropriate tone and the call is abandoned. The value of zero disables the timer. The default value of this object is 10 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..120  

ccasVoiceCfgInterDigitTimeOut 1.3.6.1.4.1.9.9.85.1.4.1.1.11
This is the inter-digit timeout that indicates the amount of time the managed system waits for a subsequent input digit from the caller. The timer is started upon receipt of an input digit and restarted as each digit is received until the destination address is identified. If the timer expires and no destination address is identified, the caller is signaled through the appropriate tone and the call is abandoned. The value of zero disables the timer. The default value of this object is 10 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..120  

ccasVoiceCfgRegionalTone 1.3.6.1.4.1.9.9.85.1.4.1.1.12
This object contains the current regional setting for the call progress tone to be used by this CAS group.
Status: current Access: read-write
OBJECT-TYPE    
  CountryCode  

ccasXgcpCfgTable 1.3.6.1.4.1.9.9.85.1.5.1
The XGCP configuration Table contains information about DS0 usage by XGCP(SGCP/MGCP). XGCP is meant to represent both Simple Gateway Control Protocol (SGCP) and Media Gateway Control Protocol (MGCP).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcasXgcpCfgEntry

ccasXgcpCfgEntry 1.3.6.1.4.1.9.9.85.1.5.1.1
An entry in the configuration table for each DS0 group of a DS1. The entry is created if the DS0 group is configured as null-signaling and ccasGrpCfgServiceType is configured as either sgcp or mgcp. The entry is deleted when the signaling type is configured as non null-signaling.
Status: current Access: not-accessible
OBJECT-TYPE    
  CcasXgcpCfgEntry  

ccasXgcpCfgCotToneCo1 1.3.6.1.4.1.9.9.85.1.5.1.1.1
This object specifies the continuity test tone frequencies for co1. Co1 is the COT tone frequency from the terminating switch in transponder mode and is from the originating switch in loopback mode.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 280..3800  

ccasXgcpCfgCotToneCo2 1.3.6.1.4.1.9.9.85.1.5.1.1.2
This object specifies the continuity test tone frequencies for co2. Co2 is the COT tone frequency from the originating switch only in transponder mode.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 280..3800  

ccasIfMIBConformance 1.3.6.1.4.1.9.9.85.3
OBJECT IDENTIFIER    

ccasIfMIBCompliances 1.3.6.1.4.1.9.9.85.3.1
OBJECT IDENTIFIER    

ccasIfMIBGroups 1.3.6.1.4.1.9.9.85.3.2
OBJECT IDENTIFIER    

ccasIfMIBCompliance 1.3.6.1.4.1.9.9.85.3.1.1
The compliance statement for entities which implement the Cisco Voice Digital interface MIB
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

ccasIfMIBComplianceRev1 1.3.6.1.4.1.9.9.85.3.1.2
The compliance statement for entities which implement the Cisco Voice Digital interface MIB
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ccasIfMIBComplianceRev2 1.3.6.1.4.1.9.9.85.3.1.3
The compliance statement for entities which implement the Cisco Voice Digital interface MIB
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ccasIfMIBComplianceRev3 1.3.6.1.4.1.9.9.85.3.1.4
The compliance statement for entities which implement the Cisco Voice Digital interface MIB
Status: current Access: read-only
MODULE-COMPLIANCE    

ccasIfDS1Group 1.3.6.1.4.1.9.9.85.3.2.1
The collection of objects providing CAS/DS0 related T1/E1 information.
Status: current Access: read-only
OBJECT-GROUP    

ccasGeneralInfoGroup 1.3.6.1.4.1.9.9.85.3.2.2
A collection of objects providing general information applicable to Channel Associated Signaling interfaces.
Status: obsolete Access: read-only
OBJECT-GROUP    

ccasEMGroup 1.3.6.1.4.1.9.9.85.3.2.3
A collection of objects providing information applicable to the CAS E&M signal interfaces.
Status: deprecated Access: read-only
OBJECT-GROUP    

ccasLineGroup 1.3.6.1.4.1.9.9.85.3.2.4
A collection of objects providing information applicable to the CAS FXS/SAS signal interfaces.
Status: current Access: read-only
OBJECT-GROUP    

ccasStaGroup 1.3.6.1.4.1.9.9.85.3.2.5
A collection of objects providing information applicable to the CAS FXO/SAO signal interfaces.
Status: current Access: read-only
OBJECT-GROUP    

ccasCustomABCDGroup 1.3.6.1.4.1.9.9.85.3.2.6
A collection of objects providing ABCD bits configuration information applicable to the CAS group on E1 interface.
Status: current Access: read-only
OBJECT-GROUP    

ccasVoiceGroup 1.3.6.1.4.1.9.9.85.3.2.7
A collection of objects providing information applicable to the CAS/DS0 group that supports voice capability.
Status: current Access: read-only
OBJECT-GROUP    

ccasGeneralInfoGroupRev1 1.3.6.1.4.1.9.9.85.3.2.8
A collection of objects providing general information applicable to CAS/DS0 interfaces.
Status: current Access: read-only
OBJECT-GROUP    

ccasChannelInfoGroup 1.3.6.1.4.1.9.9.85.3.2.9
A collection of objects providing channel signaling information applicable to Channel Associated Signaling interfaces.
Status: current Access: read-only
OBJECT-GROUP    

ccasXgcpCfgGroup 1.3.6.1.4.1.9.9.85.3.2.10
A collection of objects providing XGCP specific information applicable to DS0.
Status: current Access: read-only
OBJECT-GROUP    

ccasEMGroupRev1 1.3.6.1.4.1.9.9.85.3.2.11
A collection of objects providing information applicable to the CAS E&M signal interfaces.
Status: deprecated Access: read-only
OBJECT-GROUP    

ccasEMGroupRev2 1.3.6.1.4.1.9.9.85.3.2.12
A collection of objects providing information applicable to the CAS E&M signal interfaces.
Status: current Access: read-only
OBJECT-GROUP