CISCO-ATM-TRAFFIC-MIB

File: CISCO-ATM-TRAFFIC-MIB.mib (11575 bytes)

Imported modules

SNMPv2-SMI ATM-MIB CISCO-SMI
SNMPv2-CONF SNMP-FRAMEWORK-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE OBJECT-IDENTITY
atmTrafficDescrParamEntry ciscoExperiment MODULE-COMPLIANCE
OBJECT-GROUP SnmpAdminString

Defined Types

AtmTrafficDescrParamExtEntry  
SEQUENCE    
  atmTrafficExplicitServCategory INTEGER
  atmTrafficDerivedServCategory INTEGER
  atmTrafficDescriptorName SnmpAdminString

Defined Values

ciscoAtmTrafficExtMIB 1.3.6.1.4.1.9.10.11
This MIB module is an extension to traffic OIDs and variables defined in rfc1695.
MODULE-IDENTITY    

ciscoAtmTrafficExtMIBObjects 1.3.6.1.4.1.9.10.11.1
OBJECT IDENTIFIER    

ciscoAtmTrafficTypeExt 1.3.6.1.4.1.9.10.11.1.1
OBJECT IDENTIFIER    

ciscoAtmTrafficTableExt 1.3.6.1.4.1.9.10.11.1.2
OBJECT IDENTIFIER    

atmNoClpNoScrCdvt 1.3.6.1.4.1.9.10.11.1.1.1
Specifies peak cell rate for CLP, and cell delay variation tolerance: Parameter 1: CLP=0+1 peak cell rate in cells per second Parameter 2: CDVT in cell-times Parameter 3: not used Parameter 4: not used Parameter 5: not used. This traffic descriptor is for cbr, abr or ubr service categories, desiring to specify the cdvt as well as pcr.
OBJECT-IDENTITY    

atmClpScrMbsCdvt 1.3.6.1.4.1.9.10.11.1.1.2
This traffic descriptor is for Peak Cell Rate (PCR), Sustained Cell Rate (SCR), Maximum Burst Size applied to SCR, and Cell Delay Variation Tolerance applied to PCR. The use of the parameter vector for this type: Parameter 1: CLP=0+1 peak cell rate in cells per second Parameter 2: CLP=0 sustained cell rate in cells per second. Parameter 3: maximum burst size in cells Parameter 4: CDVT in cell-times Parameter 5: not used.
OBJECT-IDENTITY    

atmNoClpScrMbsCdvt 1.3.6.1.4.1.9.10.11.1.1.3
This traffic descriptor is for Peak Cell Rate (PCR), Sustained Cell Rate (SCR), Maximum Burst Size applied to SCR, and Cell Delay Variation Tolerance applied to PCR. The use of the parameter vector for this type: Parameter 1: CLP=0+1 peak cell rate in cells per second Parameter 2: CLP=0+1 sustained cell rate in cells per second. Parameter 3: maximum burst size in cells Parameter 4: CDVT in cell-times Parameter 5: not used.
OBJECT-IDENTITY    

atmNoClpMcr 1.3.6.1.4.1.9.10.11.1.1.4
This traffic descriptor is for Peak Cell Rate (PCR) and Minimum Cell Rate (MCR). The use of the parameter vector for this type: Parameter 1: CLP=0+1 peak cell rate in cells per second Parameter 2: CLP=0+1 minimum cell rate in cells per second. Parameter 3: not used. Parameter 4: not used. Parameter 5: not used.
OBJECT-IDENTITY    

atmNoClpMcrCdvt 1.3.6.1.4.1.9.10.11.1.1.5
This traffic descriptor is for Peak Cell Rate (PCR), Minimum Cell Rate (MCR), and Cell Delay Variation Tolerance applied to PCR. The use of the parameter vector for this type: Parameter 1: CLP=0+1 peak cell rate in cells per second Parameter 2: CDVT in cell-times Parameter 3: CLP=0+1 minimum cell rate in cells per second. Parameter 4: not used. Parameter 5: not used.
OBJECT-IDENTITY    

atmTrafficDescrParamExtTable 1.3.6.1.4.1.9.10.11.1.2.1
Provide additional information specifying traffic parameters for a VC/VP.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmTrafficDescrParamExtEntry

atmTrafficDescrParamExtEntry 1.3.6.1.4.1.9.10.11.1.2.1.1
An entry in the Traffic Parameter Descriptor extension table.
OBJECT-TYPE    
  AtmTrafficDescrParamExtEntry  

atmTrafficExplicitServCategory 1.3.6.1.4.1.9.10.11.1.2.1.1.1
This objects indicates the Service Category specified by the Traffic Descriptor. If it is defined, the setting of this object determines the Service Category used for the connection. This then limits the possible Traffic Descriptor Types as follows: Explicit Service Category Type may only be ----------------------------------------- cbr atmNoClpNoScr. atmClpNoTaggingNoScr atmClpTaggingNoScr atmNoClpNoScrCdvt abr/ubr atmNoTrafficDescriptor atmNoClpNoScr. atmNoClpNoScrCdvt atmNoClpMcr -- ubr+/abr atmNoClpMcrCdvt -- ubr+/abr vbr atmNoClpScr atmClpNoTaggingScr atmClpTaggingScr atmClpScrMbsCdvt atmNoClpScrMbsCdvt ----------------------------------------- If the settings of Service Category and Traffic Descriptor Type are not compatible, the row can not be made active.
OBJECT-TYPE    
  INTEGER cbr(1), vbrRt(2), vbrNrt(3), abr(4), ubr(5), notDef(6)  

atmTrafficDerivedServCategory 1.3.6.1.4.1.9.10.11.1.2.1.1.2
This object indicates the Service Category derived from the Traffic Descriptor. If the object atmTrafficExplicitServCategory has a defined value, then this object mirrors that value. If Explicit Service Category has the value notDef, then this object reflects the Service Category derived from the Traffic Descriptor Type as follows: Traffic Descriptor Service Type Category ----------------------------------------- atmNoTrafficDescriptor ubr atmNoClpMcr abr atmNoClpMcrCdvt abr atmNoClpNoScr --| atmClpNoTaggingNoScr |-- cbr atmClpTaggingNoScr | atmNoClpNoScrCdvt --| atmNoClpScr --| atmClpNoTaggingScr |-- vbr-rt atmClpScrMbsCdvt | atmNoClpScrMbsCdvt | atmClpTaggingScr --| -----------------------------------------
OBJECT-TYPE    
  INTEGER cbr(1), vbrRt(2), vbrNrt(3), abr(4), ubr(5)  

atmTrafficDescriptorName 1.3.6.1.4.1.9.10.11.1.2.1.1.3
A human readable string that contains the unique name of this Traffic Descriptor. This object will return a zero-length string if value is not set.
OBJECT-TYPE    
  SnmpAdminString  

ciscoAtmTrafficExtMIBConformance 1.3.6.1.4.1.9.10.11.3
OBJECT IDENTIFIER    

ciscoAtmTrafficExtMIBCompliances 1.3.6.1.4.1.9.10.11.3.1
OBJECT IDENTIFIER    

ciscoAtmTrafficExtMIBGroups 1.3.6.1.4.1.9.10.11.3.2
OBJECT IDENTIFIER    

ciscoAtmTrafficExtMIBCompliance 1.3.6.1.4.1.9.10.11.3.1.1
The compliance statement for the Cisco ATM Traffic Extension MIB.
MODULE-COMPLIANCE    

ciscoAtmTrafficExtMIBComplianceRev1 1.3.6.1.4.1.9.10.11.3.1.2
This group is optional.
MODULE-COMPLIANCE    

ciscoAtmTrafficTableExtMIBGroup 1.3.6.1.4.1.9.10.11.3.2.1
A collection of objects which provide extensions to the ATM Traffic Parameter Descriptor Table.
OBJECT-GROUP    

ciscoAtmTrafficNmsGroup 1.3.6.1.4.1.9.10.11.3.2.2
A collection of objects which provide additional information for a management system.
OBJECT-GROUP